JCBvibromaxvibromax vm

Jcb VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420)

Q: What engine powers the JCB VMT160 (FIXED) and what are the key fluid capacities?

The VMT160 (FIXED) uses a Kubota EB engine block, specifically the D1005 Tier 4 variant. The machine features a 45-litre diesel tank and a 125-litre water tank. The operating weight varies by configuration, ranging from 2670 kg (5886 lb) to 3050 kg (6724 lb). The engine power is rated at 16.8 kW (22.5 hp). Fluid specifications for the engine oil, coolant, and hydraulic systems are detailed in the factory service manual for the VMT160/VMT260 Tier 2 and Tier 4 range; specific JCB fluid designations should be verified against the machine's identification plate and service schedule.

Q: How does the hydraulic drive system differ between the VMT160 and VMT260 models?

The drum drive motors on the left side of each drum are connected in series on the VMT160, whereas they are connected in parallel on the VMT260. Both models are always driven with all drum drive engaged. The vibration system utilizes hydraulic motors driven by a charge pump, with specific pressure measurement points and flushing circuits documented in the hydraulic schematic for the VMT160/VMT260 range.

Q: What are the common electrical issues and component locations for the VMT160?

The starter relay and fuse are located in the electric frame assembly. The starter relay is labeled 'Relay, 12V/W 40A/60A WDiode; the OEM part reference-0001'. Fuse types include a 10A fuse and a 15A fuse. Common electrical faults involve the CAN-bus, EMS electrical messages, and sensor circuits. Operators should check the wiring harness for damage, particularly in the front and rear harnesses, and verify the alternator charging circuit and starter motor starting circuit if electrical faults occur.

Q: What undercarriage and drum wear patterns are typical for the VMT160?

The VMT160 is a tandem roller with smooth drums. Wear patterns typically involve the drum bearings (exciter bearings) and the vibration motor seals. The machine is available in 800mm and 900mm drum widths, with Total Side Clearance (TSC) options for the VMT160-80 and VMT160-90 models. Drum offset can be adjusted manually (left/right) as an option. Regular inspection of the drum scraper and rubber buffers is required to maintain compaction efficiency and prevent material buildup.

Q: What are the known engine quirks or maintenance points for the Kubota D1005 Tier 4 engine in this machine?

The Kubota D1005 Tier 4 engine requires attention to the fuel system, including low fuel level checks, tank draining, and fuel filter element changes. Bleeding the system is a critical procedure after filter replacement. The engine cooling pack must be inspected for blockages. Fault codes related to rail pressure control, injectors, intake pressure/temperature sensors, and turbocharger overboost are possible indicators of engine issues. Verify the engine serial number against the machine identification plate to ensure correct service procedures.

Q: What are the serial number ranges applicable to the VMT160 service manual?

The service manual for the VMT160/VMT260 Tier 2 and Tier 4 applies to specific serial number ranges. For the VMT 160-90, the applicable serial numbers are from the OEM part reference to the OEM part reference and from the OEM part reference to the OEM part reference. The machine identification plate and component identification plates must be checked to confirm the exact serial number and model variant (e.g., VMT160 (FIXED) vs. VMT160 (FIXED T.S.C)).

Q: What to check when buying a used VMT160 (FIXED)?

Verify the serial number matches the the OEM part reference-the OEM part reference or the OEM part reference-the OEM part reference ranges for the relevant Tier 2/Tier 4 manual. Check the drum bearings and vibration motor for play or leaks. Inspect the hydraulic hoses for 'Torque Stop' system integrity and 'O' Ring Face Seal connections. Test the starter relay (the OEM part reference-0001) and fuses (10A/15A) in the electric frame assembly. Confirm the engine is the Kubota D1005 Tier 4 and check for fault codes related to the ECU. Have your dealer verify the hydraulic pressure settings and engine performance specifications.

Maintenance schedule, common problems & OEM parts breakdown

Search live VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) parts

The JCB VMT160 (FIXED) is a tandem vibratory roller in the compaction class, specifically the Fixed T.S.C. configuration with serial ranges 07141/98420 and 9714101018. It is powered by a Kubota D1005 Tier 4 engine delivering 16.8 kW (22.5 hp). Operating weight ranges from 2670 to 3050 kg (5886 to 6724 lb) depending on drum width (800 mm or 900 mm). Production years span 2008 to 2019. It succeeds earlier Vibromax models and is succeeded by the VMT260 series. Configurations include Fixed T.S.C. and standard drum widths.

Across generations, the VMT160 evolved from Tier 2 to Tier 4 emissions compliance, requiring engine upgrades and DEF system integration. The Fixed T.S.C. variant introduced total side clearance for improved edge compaction. The machine matters in the used/parts market due to its widespread use in road construction and the availability of Kubota engine components. Serial breaks at the OEM part reference and the OEM part reference distinguish Tier 2 and Tier 4 service manuals, affecting parts compatibility and maintenance procedures.

Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.

Jcb VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) specifications

Engine

Model	Kubota EB (Tier 4)
Power (Net)	16.8 kW (22.5 hp)
Emissions Tier	Tier 4

Weights

Operating Weight

2670 – 3050 kg (5886 – 6724 lb)

Dimensions

Transport Length	2.05 – 2.14 m (6 ft 9 in – 7 ft 0 in)
Transport Width	0.88 – 1.08 m (2 ft 11 in – 3 ft 7 in)
Transport Height	2.32 m (7 ft 7 in)
Drum Width	800 – 1000 mm (31.5 – 39.4 in)

Performance

Exciter Frequency	Not documented for this exact serial range — verify with your dealer
Nominal Amplitude	Not documented for this exact serial range — verify with your dealer
Centrifugal Force (each drum)	Not documented for this exact serial range — verify with your dealer

Service capacities (summary)

Fuel Tank	45 L (11.9 gal)
Water Tank	125 L (33.0 gal)

Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.

Jcb VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) maintenance schedule

Service interval	Tasks
Every 10 h	Check engine oil level. Check coolant level. Check hydraulic oil level. Check water tank level. Inspect drum condition. Check seat and seat belt.
Every 250 h	Change engine oil. Replace engine oil filter. Replace engine fuel filter element. Bleed fuel system. Check drive belt tension. Inspect hydraulic hoses and fittings.
Every 500 h	Replace hydraulic oil filter. Replace water filter element. Clean sprinkler system. Check battery electrolyte specific gravity. Inspect ROPS structure. Check articulation joint.
Every 1,000 h	Replace hydraulic oil. Replace engine air filter. Inspect vibration system. Check exciter bearing clearance. Inspect drum offset mechanism. Check electrical connections.
Every 2,000 h	Replace coolant. Inspect vibration motors. Check hydraulic pump pressures. Inspect steering control unit. Check drum drive motor condition. Inspect all grease points.

Servicing the VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) beyond the schedule

Predictive Maintenance & Fluid Analysis

Monitor hydraulic oil quality in the VMT160 propulsion and vibration circuits. Check exciter bearing clearance during fluid changes to detect wear. Analyze engine oil for Kubota D1005 contamination. Inspect drum offset mechanism hydraulic lines for leaks. Track water filter element condition to prevent sprinkler system clogging. Monitor vibration frequency and amplitude for consistency.

Corrective & Common Repairs

Replace engine fuel filter and bleed system if Kubota D1005 starts poorly. Fix hydraulic hose leaks using 'O' Ring Face Seal or 'Torque Stop' systems. Replace vibration motor seals if drum vibration is weak. Repair drum offset hydraulic rams for manual adjustment issues. Check starter relay and fuses in the electric frame assembly for electrical faults. Inspect articulation joint for steering play.

Overhaul & Rebuild Points

Rebuild vibration motors at 2000 hours or if performance drops. Overhaul drum drive hydraulic motors if traction fails. Replace exciter bearings if noise or heat indicates failure. Rebuild hydraulic pumps if pressure tests show deviation. Inspect Kubota D1005 engine block for wear. Check drum structure for cracks near weld points. Replace all seals in the vibration system during major service.

Seasonal & Environment Servicing

Drain and clean sprinkler system to prevent freezing in cold weather. Check coolant mixture for antifreeze protection. Inspect rubber buffers on drums for wear in abrasive environments. Clean engine cooling pack to prevent overheating in dusty conditions. Grease all articulation and vibration system points regularly. Check battery charge and electrolyte level for cold starts.

VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) common service parts

Part number	Part	Notes
4029/69675	Filter, Fuel	Fuel system service	Check fitment →
7141/50122	Filter, Fuel	Fuel system service	Check fitment →
32/925742	Element, Air Filter	Air intake service	Check fitment →
7141/54102	Element, Safety (Air)	Air intake service	Check fitment →
7170/54100	Filter, Air Cleaner	Air intake service	Check fitment →

Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.

VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) fault codes & troubleshooting

Code	Meaning	Likely cause	What to do
E001	High hydraulic oil temperature	Oil cooler failure, low oil level, or excessive load	Check the cooler, fill oil to proper level, avoid operating under excessive load
E002	Low hydraulic oil level	Leak in the hydraulic system	Refill oil level, locate and repair the leak
E011	Low engine oil pressure	Oil pump failure, oil filter clogging, or low oil level	Check and repair oil pump, filter, and level as necessary
E034	Hydraulic oil filter clogged	Excessive filter contamination	Replace the hydraulic oil filter
E041	Fuel filter clogged	Excessive filter contamination	Replace the fuel filter
E050	Air filter clogged	Excessive filter contamination	Replace the air filter
E060	High water temperature	Cooling system failure, low water level, or excessive load	Check cooling system, fill water level, avoid operating under load
E080	Left joystick fault	Left joystick malfunction	Check and repair or replace the left joystick
E100	Safety latch disengaged	Safety latch is disengaged	Engage the safety latch
P2201	NOx Sensor Signal Out of Range (Bank 1)	NOx sensor dirty, failing, or wiring damaged	Check wiring harness for breaks or corrosion at the connector

Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.

VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) attachments & work tools

Drum Width Configurations

The VMT160 is offered in 800mm and 900mm drum widths, designated as VMT160-80 and VMT160-90 respectively. These configurations are available in both Fixed and Total Side Clearance (TSC) variants, with the TSC versions specifically noted for the 800mm and 900mm widths.

Operating Weight Class

Operating weight varies by configuration and series, ranging from 2670 kg (5886 lb) to 3050 kg (6724 lb). Specific model variants include the VMT160-80 at approximately 1.6 tons and the VMT160-100 at approximately 1.81 tons.

Engine Specifications

The machine utilizes a Kubota D1005 Tier 4 engine, delivering 16.8 kW (22.5 hp). This engine configuration is associated with the VMT160 (FIXED) designation and serial ranges starting from JCB 28 020 75-.

Fluid Capacities

The VMT160 features a 45-litre diesel fuel tank and a 125-litre water tank for the sprinkler system. These capacities are standard across the VMT160 range to support extended operation times.

Serial Number Applicability

Service documentation for the VMT160-90 applies to serial numbers the OEM part reference to the OEM part reference and the OEM part reference to the OEM part reference. Parts catalogs for the VMT160 (FIXED T.S.C) cover serial range the OEM part reference to the OEM part reference.

Hydraulic System Configuration

The vibration system uses hydraulic motors driven by a dedicated vibration/charge pump. On the VMT160, the drum drive motors are connected in series, whereas the VMT260 uses a parallel connection. The system employs 'O' Ring Face Seal and 'Torque Stop' hose systems.

Transport Dimensions

Transport dimensions vary by model variant. The VMT160-80 measures 2.05 m in length and 0.88 m in width. The VMT160-100 measures 2.14 m in length and 1.08 m in width. Both variants have a transport height of 2.32 m.

All VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) assemblies by section

Every catalogued assembly group for the Jcb VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420). Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.

B Bodywork, Cab

B1-12-2 Scraper, Complete, 800 Mm > S/N 2802386

13***9Z	Setscrew, M8x35	40
13***8Z	Bolt, M10 X 30	8
13***3Z	Nut, Self Lock, M8	40
14***7Z	Washer, Plain, M8; Replaces Khn1550, San 12620	76

See all parts with full part numbers in Heavy Parts AI →

B1-2-10 Articulation Joint, Fixed, Salvage

13***0Z	Screw, M12 X 40 mm Long	1
14***9Z	Washer	1
20***20	Capscrew, M8x20	12
22***30	Bearing	2

See all parts with full part numbers in Heavy Parts AI →

B1-12-10 Scraper, Complete, 900 Mm < S/N 2802385

20***35	Screw, Hexagon M8x35	36
20***30	Screw, Hexagon M10 X 30	8
21***20	Nut, M20	8
21***00	Nut, M8	40

See all parts with full part numbers in Heavy Parts AI →

B1-12-20 Scraper, Complete, 1000 Mm < S/N 2802385

20***35	Screw, Hexagon M8x35	56
20***30	Screw, Hexagon M10 X 30	8
21***20	Nut, M20	8
21***00	Nut, M8	56

See all parts with full part numbers in Heavy Parts AI →

B1-1-1 Chassis, Hydraulic Tank

13***3Z	Screw, M8 X 16	8
20***16	Screw, Hexagom M8x16	8
20***20	Screw, Hexagon M8x20	4
20***30	Capscrew, M6x30	4

See all parts with full part numbers in Heavy Parts AI →

B1-3-1 Water Tank

20***20	Screw, Hexagon M8x20	6
71***00	Tank, Water	1
71***01	Cap, Water Tank	1
71***11	Cover	1

See all parts with full part numbers in Heavy Parts AI →

B1-2-1 Articulation Joint, Fixed

20***25	Screw, Hexagon M10x25	1
20***20	Capscrew, M8x20	12
21***00	Nut, M16	2
22***10	Washer, M10	1

See all parts with full part numbers in Heavy Parts AI →

B1-12-21 Scraper, Complete, 1000 Mm > S/N 2802386

13***9Z	Setscrew, M8x35	60
13***8Z	Bolt, M10 X 30	8
13***3Z	Nut, Self Lock, M8	60
14***7Z	Washer, Plain, M8; Replaces Khn1550, San 12620	120

See all parts with full part numbers in Heavy Parts AI →

B1-12-11 Scraper, Complete, 900 Mm > S/N 2802386

13***9Z	Setscrew, M8x35	40
13***8Z	Bolt, M10 X 30	8
13***3Z	Nut, Self Lock, M8	40
14***7Z	Washer, Plain, M8; Replaces Khn1550, San 12620	80

See all parts with full part numbers in Heavy Parts AI →

B1-12-1 Scraper, Complete, 800 Mm < S/N 2802385

20***35	Screw, Hexagon M8x35	36
20***30	Screw, Hexagon M10 X 30	8
21***20	Nut, M20	8
21***00	Nut, M8	40

See all parts with full part numbers in Heavy Parts AI →

B2-8-1 Rops Frame

20***85	Screw, Hexagon M20x85, Screw,Hex, M20 X 85, 8.8; M20 X 85, Screw,Hex, M20 X 85, 8.8; M20x85	2
20***70	Capscrew, M16x70	4
21***00	Nut, M16	4
21***00	Nut, M20	2

See all parts with full part numbers in Heavy Parts AI →

B2-6-1 Seat, Components

71***00	Seat, Operator	1
71***05	Buffer	1
71***06	Spring, Tension	1
71***07	Buffer, Shock	1

See all parts with full part numbers in Heavy Parts AI →

B2-1-1 Bonnet, Engine Cover

20***16	Screw, Hex, M5x16	8
20***50	Capscrew, M10x50	2
21***00	Nut, M5	8
21***00	Nut, M6	2

See all parts with full part numbers in Heavy Parts AI →

B2-9-1 Cover, Plate

20***13	Screw, Tapping, 8x13	4
21***08	Nut	2
22***08	Washer, M8	2
27***22	Handle	1

See all parts with full part numbers in Heavy Parts AI →

B2-5-1 Operators Stand

20***20	Screw, Hexagon M6x20	4
20***16	Screw, Hexagom M8x16	4
20***30	Capscrew, M5x30	2
20***20	Capscrew, M8x20	8

See all parts with full part numbers in Heavy Parts AI →

B5-4-1 Decals, Service

27***70	Service Decal, German	1
27***71	Service Decal, English	1

See all parts with full part numbers in Heavy Parts AI →

B5-3-1 Decals

33***08	Decal, Warning-Fan Blades, Remove Key From Ign.	2
81***55	Label, Diesel	1
81***52	Label, Battery, Isolator	1
81***04	Decal, Warning,Hot Surfaces, Keep Clear	1

See all parts with full part numbers in Heavy Parts AI →

B5-1-1 Decals, Machine

27***20	Decal, Jcb, Black	2
27***10	Decal, Jcb Black	2
40***57	Decal, Warning Indication	1
40***04	Decal, Warning Indication	1

See all parts with full part numbers in Heavy Parts AI →

B5-2-1 Decals

27***14	Decal, Water	1
27***20	Decal, Sprinkling	1
27***01	Decal, Oil Level	1
27***23	Decal, Hlp 46	1

See all parts with full part numbers in Heavy Parts AI →

C Electrics, Machine, Cab And Engine

C1-2-1 Electrics, Pcb

20***25	Screw, Hexagon M8x25	1
20***12	Capscrew, M3x12	4
20***10	Screw	6
21***03	Nut, Hex M3	4

See all parts with full part numbers in Heavy Parts AI →

C1-3-1 Machine, Lights

20***16	Screw, M6 X 16	2
20***25	Screw, Hexagon M8x25	4
20***25	Screw, Hexagon M10x25	4
20***12	Capscrew, M4x12	16

See all parts with full part numbers in Heavy Parts AI →

C1-3-2 Machine, Lights

13***1Z	Nut, M8	4
14***4Z	Washer, M4; Replaces Khn0424, San 12352	8
20***25	Screw, Hexagon M8x25	4
20***16	Capscrew, M4x16	4

See all parts with full part numbers in Heavy Parts AI →

C1-7-1 Beacon

70***04	Decal, Beacon Switch	1
70***00	Switch, 12v	1
70***37	Gasket, Panel Switch	1
71***00	Beacon, Rotating	1

See all parts with full part numbers in Heavy Parts AI →

C1-1-11 Cover, Instrument Panel, > S/N 2802387

14***6Z	Washer, M6	4
20***10	Capscrew, M6x10	4
20***14	Screw, M6x14	3
29***01	Lock	1

See all parts with full part numbers in Heavy Parts AI →

C1-1-1 Instrument Panel

20***14	Screw, M6x14	1
27***25	Plug, Gl 25	1
33***48	Switch, Vibration, Rear	1
33***49	Switch, Vobration, Front	1

See all parts with full part numbers in Heavy Parts AI →

C1-1-10 Cover, Instrument Panel, < S/N 2802386

20***16	Capscrew, M6x16	9
20***10	Capscrew, M6x10	4
22***06	Washer, M6	13
29***01	Lock	1

See all parts with full part numbers in Heavy Parts AI →

C2-1-1 Battery, & Isolator

20***20	Screw, Hexagon M6x20	2
21***00	Nut, M8	5
21***00	Nut, M6	2
22***08	Washer, M8	6

See all parts with full part numbers in Heavy Parts AI →

D Controls, Machine, Cab And Engine

D3-1-1 Steering Column, Complete

20***35	Screw, Hexagon M10x35	4
25***29	Grommet, Seal, Steering Column	1
33***87	Cap, Steering Wheel	1
33***04	Steering Orbital, Valve	1

See all parts with full part numbers in Heavy Parts AI →

E Hydraulics

E1-8-1 Circuit, Test Points

25***08	Adapter	2
25***08	Adapter	2
25***29	Socket, Test	2
25***30	Connector	1

See all parts with full part numbers in Heavy Parts AI →

E1-7-1 Circuit, Oil, Leakage Return Line

22***18	Washer	2
25***12	Connector	1
25***15	Union, Flange	1
25***08	Reducer	2

See all parts with full part numbers in Heavy Parts AI →

E1-2-2 Circuit, Drive, >2802150

20***22	Capscrew, M6x22	14
20***35	Capscrew, M6x35	16
20***60	Capscrew, M8x60	2
22***08	Washer, M8	2

See all parts with full part numbers in Heavy Parts AI →

E1-6-1 Circuit, Cooling

20***20	Screw, Hexagon M8x20	2
20***60	Screw, Hex, M8x60	3
21***00	Nut, M8	3
22***08	Washer, M8	5

See all parts with full part numbers in Heavy Parts AI →

E1-3-1 Circuit, Steering

25***15	Reducer	1
25***12	Adapter	1
25***14	Adapter	1
25***15	Adapter	1

See all parts with full part numbers in Heavy Parts AI →

E1-5-1 Circuit, Park Brake

25***03	Adapter	3
25***08	Adapter	2
25***08	Connector	1
28***86	Hose, 950mm Long	1

See all parts with full part numbers in Heavy Parts AI →

E1-4-1 Circuit, Hydraulic Oil, Filter

25***15	Adapter	3
25***19	Connector	1
25***15	Adapter	2
25***15	Adapter	1

See all parts with full part numbers in Heavy Parts AI →

E1-1-1 Circuit, Propulsion, <2802149

20***20	Screw, Hexagon M8x20	3
22***08	Washer, M8	3
25***12	Connector	2
25***13	Connector	4

See all parts with full part numbers in Heavy Parts AI →

E1-1-2 Circuit, Propulsion, >2802150

20***20	Screw, Hexagon M8x20	3
22***08	Washer, M8	3
25***17	Connector, G16/12-S	1
25***12	Connector, 12-S/A3c	1

See all parts with full part numbers in Heavy Parts AI →

E1-2-1 Circuit, Drive, <2802149

20***22	Capscrew, M6x22	14
20***35	Capscrew, M6x35	16
20***60	Capscrew, M8x60	2
22***08	Washer, M8	2

See all parts with full part numbers in Heavy Parts AI →

E2-4-1 Motor, Drive, Proclain

71***33	O Ring	1
71***08	Plug	1
71***07	Housing, Motor	1
71***08	Seal, Oil	1

See all parts with full part numbers in Heavy Parts AI →

E2-1-1 Hydraulic Pump, Pump Drive, <2802149

13***9Z	Screw, M12 X 35mm, Screw, M12 X 35mm; M12 X 35. Items 21 & 22 Are Used On 23*00 And 23*00 Throttle Brackets	2
14***5Z	Washer, M5; Replaces 69***59	1
20***35	Screw, Hex, M12x35	2
20***20	Capscrew, M5x20	1

See all parts with full part numbers in Heavy Parts AI →

E10-1-1 Sprinkler System

20***70	Screw, Hexagon M8x70	2
20***25	Capscrew, M5x25	4
20***45	Capscrew, M6x45	4
21***00	Nut, M6	4

See all parts with full part numbers in Heavy Parts AI →

E20-2-1 Conversion Kit, Hose, Vmt 160-90 <2802149

23***22	Clamp	15
25***17	Connector, G16/12-S	1
25***16	Reducer	2
25***12	Insert, Reducing	2

See all parts with full part numbers in Heavy Parts AI →

E20-4-1 Conversion Kit, Hose, Vmt 160 Tier 4 <2802149

23***22	Clamp	15
25***17	Connector, G16/12-S	1
25***16	Reducer	2
25***12	Insert, Reducing	2

See all parts with full part numbers in Heavy Parts AI →

E20-1-1 Conversion Kit, Hose, Vmt 160-80 <2805149

23***22	Clamp	15
25***17	Connector, G16/12-S	1
25***16	Reducer	2
25***12	Insert, Reducing	2

See all parts with full part numbers in Heavy Parts AI →

E20-3-1 Conversion Kit, Hose, Vmt 160-100 <2802149

23***22	Clamp	15
25***17	Connector, G16/12-S	1
25***16	Reducer	2
25***12	Insert, Reducing	2

See all parts with full part numbers in Heavy Parts AI →

F Axles, Wheels & Transmission

F1-1-1 Drum, 800 Mm

20***30	Screw	4
20***35	Screw, Hex, M12x35	4
20***55	Screw, Bolt,Hex, M12 X 1.75 X 55mm, Cl 8.8; M12x55x55, Bolt,Hex, M12 X 1.75 X 55mm, Cl 8.8; M12 X 55 X 55	8
20***40	Screw, M16x40	5

See all parts with full part numbers in Heavy Parts AI →

F1-2-10 Drum, 900 Mm

20***30	Screw, Hex M10x30	16
20***25	Capscrew, M8x25	4
22***08	Washer, M8	4
22***10	Washer, M10	16

See all parts with full part numbers in Heavy Parts AI →

F1-1-10 Drum, 800 Mm

20***30	Screw, Hex M10x30	16
20***25	Capscrew, M8x25	4
22***08	Washer, M8	4
22***10	Washer, M10	16

See all parts with full part numbers in Heavy Parts AI →

F1-3-1 Drum, 1000 Mm

20***50	Screw, Hexagon	8
20***30	Screw	4
20***35	Screw, Hex, M12x35	4
20***40	Screw, M16x40	5

See all parts with full part numbers in Heavy Parts AI →

F1-2-1 Drum, 900 Mm

20***10	Bolt, M12x110mm	8
20***30	Screw	4
20***35	Screw, Hex, M12x35	4
20***40	Screw, M16x40	5

See all parts with full part numbers in Heavy Parts AI →

F1-3-10 Drum, 1000 Mm

20***30	Screw, Hex M10x30	16
20***25	Capscrew, M8x25	4
22***08	Washer, M8	4
22***10	Washer, M10	16

See all parts with full part numbers in Heavy Parts AI →

N Engine D1005 Tier 4, Kubota Eb

N1-6-2 Governor, Fuel Camshaft

02***98	Camshaft, Fuel	1
02***71	Stopper, Fuel.C/Shaft	1
02***15	Pivot, Pin	2
02***16	Holder, ,Gov.Weight	1

See all parts with full part numbers in Heavy Parts AI →

N1-5-1 Fan Drive

02***33	Pulley, ,Fan	1
02***48	Fan, .	1
33***13	Bolt	4
33***16	Spacer, Fan	1

See all parts with full part numbers in Heavy Parts AI →

N1-10-1 Engine Mounting

20***25	Screw	16
20***20	Screw, Hexagon M8x20	8
20***25	Screw, Hexagon M10x25	4
22***10	Washer, M10	4

See all parts with full part numbers in Heavy Parts AI →

N1-6-3 Idler Adjuster

02***69	Gasket	3
02***89	Nut	1
02***72	Nut	2
02***32	Cap	1

See all parts with full part numbers in Heavy Parts AI →

N1-9-1 Alternator, Mountings

02***21	Nut	1
02***40	Pulley, ,Fan Drive	1
02***28	Stay,Dynamo	1
02***33	Pulley, ,Fan	1

See all parts with full part numbers in Heavy Parts AI →

N1-8-1 Flywheel Assy.

02***69	Bolt	8
02***53	Plate	1
02***95	Bolt, Flywheel	6
02***41	Flywheel, Complete	1

See all parts with full part numbers in Heavy Parts AI →

N1-6-1 Timing Cover

02***03	Nut, Flange	1
02***07	Screw	5
02***22	Pin, Straight	2
02***64	Joint, Ring	1

See all parts with full part numbers in Heavy Parts AI →

N1-3-1 Engine Block

02***49	Cap, Sealing	1
02***55	Plug	1
02***63	Pin, Pipe	2
02***72	Plug	3

See all parts with full part numbers in Heavy Parts AI →

N1-6-5 Governor Assembly

02***21	Collar	1
02***23	Cover, ,Fork Lev.Shaft	1
02***24	Bearing	1
02***25	Bearing	1

See all parts with full part numbers in Heavy Parts AI →

N1-7-1 Camshaft And Idler

02***63	Screw, Set	1
02***69	Push Rod	6
02***70	Stopper, Camshaft	1
02***72	Gear, Cam	1

See all parts with full part numbers in Heavy Parts AI →

N1-2-1 Crankshaft Pistons, Conrods

02***16	Ring	1
02***93	Washer, Thrust, Std	2
02***94	Washer, Thrust, +0.20mm	2
02***95	Washer, Thrust, +0.40mm	2

See all parts with full part numbers in Heavy Parts AI →

N1-1-1 Engine, Diesel, Kubota D1005 E3b 16.8kw 3000rpm

71***00	Engine, Kubota Diesel D1005-E3b-Eu-Xl1 16.8kw 3000 Rpm	1
87***02	Engine, Build Assembly	1

See all parts with full part numbers in Heavy Parts AI →

N1-6-6 Throttle Control

02***03	Nut, Flange	2
02***14	O Ring	1
02***87	Seal, Oil	1
02***69	Gasket	1

See all parts with full part numbers in Heavy Parts AI →

N1-6-4 Stop Solenoid

02***48	Solenoid, Stop, Assembly	1
02***12	Bolt, .	2
33***58	Wire, Solenoid; Techweb Bulletin4582	1

See all parts with full part numbers in Heavy Parts AI →

N1-4-1 Bearings, Crankshaft

02***51	Bolt, Bearing Case	6
02***52	Bolt, Bearing Case	2
02***55	Cover, Bearing Case	1
02***84	Bearing, Std	2

See all parts with full part numbers in Heavy Parts AI →

N2-2-2 Rocker Assembly, And Valves

02***83	Bolt, .	2
02***68	Collet,Valve Spring, Set	6
02***70	Nut	3
02***71	Washer, Plain	3

See all parts with full part numbers in Heavy Parts AI →

N2-3-1 Rocker Cover

02***08	Screw, Pan-Head	4
02***25	Clamp, Hose	1
02***93	Gasket	3
02***94	Nut	3

See all parts with full part numbers in Heavy Parts AI →

N2-1-1 Cylinder Head, Lifting Brackets

02***67	Cap, Sealing	2
02***72	Plug	2
02***78	Cap, Sealing	1
02***46	Hook, Engine	1

See all parts with full part numbers in Heavy Parts AI →

N3-3-1 Air Filter

20***20	Screw, Hexagon M8x20	2
20***30	Screw, Hexagon M10 X 30	4
21***00	Nut, M8	2
22***08	Washer, M8	4

See all parts with full part numbers in Heavy Parts AI →

N3-4-3 Exhaust System, Hose Installation

20***20	Screw, Hexagon M8x20	2
20***25	Screw, Hexagon M8x25	2
22***08	Washer, M8	4
25***37	Clamp	1

See all parts with full part numbers in Heavy Parts AI →

N3-1-1 Inlet Manifold

02***74	Clamp, Cord	1
02***56	Joint,Breather Pipe	1
02***59	Gasket, In-Manifold	1
02***39	Bolt	3

See all parts with full part numbers in Heavy Parts AI →

N3-4-1 Exhaust Silencer

02***60	Gasket, Ex-Manifold	1
33***71	Silencer, Assembly	1
33***90	Cover, Silencer	1
33***95	Bolt	3

See all parts with full part numbers in Heavy Parts AI →

N4-3-1 Hose Water Pump

02***46	Pipe, Water	1
02***24	Pipe, Water	1
02***74	Clamp	2

See all parts with full part numbers in Heavy Parts AI →

N4-2-1 Thermostat Housing

02***31	Cover, Thermostat	1
02***30	Pipe, Water Return	1
02***31	Band,Pipe	2
02***32	Pipe, Water Return	1

See all parts with full part numbers in Heavy Parts AI →

N4-4-1 Expansion Bottle

02***14	Gasket, Seal	1
02***17	Clip, Pipe	1
33***18	Pipe, Water Over Flow	1
33***22	Pipe, Over Flow	1

See all parts with full part numbers in Heavy Parts AI →

N4-1-1 Water Pump

02***85	Bolt	2
02***45	Gasket, Water Pump	1
02***48	Pump, Water. Assembly	1
02***01	Bolt, .	4

See all parts with full part numbers in Heavy Parts AI →

N4-3-2 Installation Cooler, Radiator & Hoses

02***36	Clamp, Hose	2
02***42	Clamp, Hose	2
07***75	Kit, Sealing Strip	1
13***9Z	Setscrew, M8x35	2

See all parts with full part numbers in Heavy Parts AI →

N5-3-1 Oil Pump

02***19	O Ring	4
02***24	Bolt	6
02***18	O Ring, .	1
02***21	O Ring, .	1

See all parts with full part numbers in Heavy Parts AI →

N5-1-2 Sump, Drain

22***18	Washer	4
25***15	Plug	1
25***12	Connector	1
25***12	Adapter	1

See all parts with full part numbers in Heavy Parts AI →

N5-1-1 Sump

02***41	Plug, Drain	1
02***60	Bolt	22
02***74	Plug, Drain	1
02***39	Filter, Oil	1

See all parts with full part numbers in Heavy Parts AI →

N5-2-1 Dipstick

02***13	O Ring	1
02***62	Guide, Oil Gauge, Assembly	1
02***18	Gauge, Oil	1
02***97	Plug, ,Oil Gauge	1

See all parts with full part numbers in Heavy Parts AI →

N5-4-1 Oil Filter

02***91

Cartridge, Oil Filter

See all parts with full part numbers in Heavy Parts AI →

N6-2-2 Fuel Pump Plate

02***03	Nut, Flange	1
02***71	Cover	1
02***80	Gasket, Fuel Pump	1
02***22	Pump, Fuel Assembly	1

See all parts with full part numbers in Heavy Parts AI →

N6-2-4 Fuel Injector

02***84	Gasket	1
02***11	Nozzle, Nut	1
02***13	Nut	1
02***14	Washer, Plain	1

See all parts with full part numbers in Heavy Parts AI →

N6-1-1 Injection Pump

02***78	Screw	1
02***88	Stud	2
02***91	Nut	2
02***95	Gasket	2

See all parts with full part numbers in Heavy Parts AI →

N6-2-1 Fuel Filter, Fuel Lines

20***12	Screw, Hexagon M6x12	1
20***25	Screw, Hexagon M8x25	2
22***08	Washer, M8	2
23***09	Clamp	10

See all parts with full part numbers in Heavy Parts AI →

VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) serial number reference

Locate the machine identification plate on the frame to verify the serial number and configuration. Confirm applicability with a JCB dealer.

Prefix	Identifies	Notes
1700515 to 1701469	JCB Vibromax VMT160-90 (Tier 2 and Tier 4)
2802000 to 2804999	JCB Vibromax VMT160-90 (Tier 2 and Tier 4)
02802000 to 02804999	JCB Vibromax VMT160 (FIXED T.S.C) 800mm, 900mm
02802332 to 02804999	JCB Vibromax VMT160 800mm
JCB 28 020 75-	JCB Vibromax VMT160 (FIXED)

Frequently asked questions

What engine does the VMT160 (FIXED) use?

Kubota D1005 Tier 4

What is the operating weight?

2670 to 3050 kg (5886 to 6724 lb)

What replaced the VMT160?

VMT260 series

What VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) owners discuss

What engine powers the JCB VMT160 (FIXED) and what are the key fluid capacities?

The VMT160 (FIXED) uses a Kubota EB engine block, specifically the D1005 Tier 4 variant. The machine features a 45-litre diesel tank and a 125-litre water tank. The operating weight varies by configuration, ranging from 2670 kg (5886 lb) to 3050 kg (6724 lb). The engine power is rated at 16.8 kW (22.5 hp). Fluid specifications for the engine oil, coolant, and hydraulic systems are detailed in the factory service manual for the VMT160/VMT260 Tier 2 and Tier 4 range; specific JCB fluid designations should be verified against the machine's identification plate and service schedule.

How does the hydraulic drive system differ between the VMT160 and VMT260 models?

The drum drive motors on the left side of each drum are connected in series on the VMT160, whereas they are connected in parallel on the VMT260. Both models are always driven with all drum drive engaged. The vibration system utilizes hydraulic motors driven by a charge pump, with specific pressure measurement points and flushing circuits documented in the hydraulic schematic for the VMT160/VMT260 range.

What are the common electrical issues and component locations for the VMT160?

The starter relay and fuse are located in the electric frame assembly. The starter relay is labeled 'Relay, 12V/W 40A/60A WDiode; the OEM part reference-0001'. Fuse types include a 10A fuse and a 15A fuse. Common electrical faults involve the CAN-bus, EMS electrical messages, and sensor circuits. Operators should check the wiring harness for damage, particularly in the front and rear harnesses, and verify the alternator charging circuit and starter motor starting circuit if electrical faults occur.

What undercarriage and drum wear patterns are typical for the VMT160?

The VMT160 is a tandem roller with smooth drums. Wear patterns typically involve the drum bearings (exciter bearings) and the vibration motor seals. The machine is available in 800mm and 900mm drum widths, with Total Side Clearance (TSC) options for the VMT160-80 and VMT160-90 models. Drum offset can be adjusted manually (left/right) as an option. Regular inspection of the drum scraper and rubber buffers is required to maintain compaction efficiency and prevent material buildup.

What are the known engine quirks or maintenance points for the Kubota D1005 Tier 4 engine in this machine?

The Kubota D1005 Tier 4 engine requires attention to the fuel system, including low fuel level checks, tank draining, and fuel filter element changes. Bleeding the system is a critical procedure after filter replacement. The engine cooling pack must be inspected for blockages. Fault codes related to rail pressure control, injectors, intake pressure/temperature sensors, and turbocharger overboost are possible indicators of engine issues. Verify the engine serial number against the machine identification plate to ensure correct service procedures.

What are the serial number ranges applicable to the VMT160 service manual?

The service manual for the VMT160/VMT260 Tier 2 and Tier 4 applies to specific serial number ranges. For the VMT 160-90, the applicable serial numbers are from the OEM part reference to the OEM part reference and from the OEM part reference to the OEM part reference. The machine identification plate and component identification plates must be checked to confirm the exact serial number and model variant (e.g., VMT160 (FIXED) vs. VMT160 (FIXED T.S.C)).

What to check when buying a used VMT160 (FIXED)?

Verify the serial number matches the the OEM part reference-the OEM part reference or the OEM part reference-the OEM part reference ranges for the relevant Tier 2/Tier 4 manual. Check the drum bearings and vibration motor for play or leaks. Inspect the hydraulic hoses for 'Torque Stop' system integrity and 'O' Ring Face Seal connections. Test the starter relay (the OEM part reference-0001) and fuses (10A/15A) in the electric frame assembly. Confirm the engine is the Kubota D1005 Tier 4 and check for fault codes related to the ECU. Have your dealer verify the hydraulic pressure settings and engine performance specifications.

Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.

Serial-range & configuration variants

This page covers the Jcb VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420). Related factory variants of the same model family:

VMT160(800mm, 900mm, 1000mm (Tier 2))VMT160 (FIXED T.S.C)(VMT160 (FIXED T.S.C))

Need a specific VMT160 (FIXED)(FIXED VMT (9714101018) 07141/98420) part?

Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.

Search parts in the app