JCBagriculturalbackhoe loader 3cx,4cx,214,215,217
Jcb 3CX-2
Maintenance schedule, common problems & OEM parts breakdown
The JCB 3CX-2 is a compact backhoe loader designed for utility, municipal, and general contracting work in tight urban environments. Produced from 2008 through 2025, it succeeded the 3CX-1 and preceded the 3CX Plus generation. The machine features a JCB DieselMax 4-cylinder turbocharged engine delivering 74.6 kW (100 hp) or a JCB EcoMAX variant, with an operating weight ranging from approximately 6,616 kg (14,586 lb) to 8,300 kg (18,300 lb) depending on configuration. Configurations include 2-wheel drive (2WD) and 4-wheel drive (4WD) options, with standard 4-wheel steering and a compact footprint optimized for road repair and trenching.
Across its production run, the 3CX-2 evolved from earlier 3CX models by integrating Tier 4 Final emissions compliance without using Diesel Exhaust Fluid (DEF) or a Diesel Particulate Filter (DPF). This architectural choice eliminated aftertreatment regeneration cycles and DEF consumption, significantly reducing annual maintenance overhead compared to competitors. The machine remains critical in the used and parts market because its simplified emissions architecture avoids the complex sensor and filter failures common in DEF-equipped backhoes, while its 500-hour engine oil interval offers superior uptime for high-utilization contractors.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Jcb 3CX-2 specifications
Engine
| Model | JCB DieselMax (444 series) |
| Net Power | 74.6 kW (100 hp) |
| Gross Power | 61.67 kW (82.7 hp) |
| Displacement | 4,401.58 cm³ (268.6 in³) |
| Cylinders | 4 |
| Emissions Tier | Tier 4 Final / Stage V |
Weights
| Operating Weight | 8,300 kg (18,300 lb) |
| Operating Weight (Variants) | 7,370–8,070 kg (16,250–17,800 lb) |
Dimensions
| Transport Length | 6,160 mm (242.5 in) |
| Transport Width | 2,400 mm (94.5 in) |
| Transport Height | 3,890 mm (153.1 in) |
| Wheelbase | 2,480 mm (97.6 in) |
| Ground Clearance | 380 mm (15.0 in) |
Performance
| Travel Speed (Forward) | 40 km/h (24.9 mph) |
| Travel Speed (Reverse) | 36.21 km/h (22.5 mph) |
| Max Digging Depth | 5,870 mm (19.3 ft) |
| Max Reach from Swing Post | 6,245 mm (20.5 ft) |
| Loader Lift Capacity | 3,300 kg (7,275 lb) |
| Loader Bucket Capacity | 1.0–1.3 m³ (1.3–1.7 yd³) |
| Backhoe Bucket Capacity | 0.2–0.3 m³ (0.26–0.39 yd³) |
Service capacities (summary)
| Fuel Tank | 130 L (34.3 gal) |
| Hydraulic System | 160 L (42.2 gal) |
| Engine Oil | 15.14 L (4.0 gal) |
| Cooling System | 18.55 L (4.9 gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
3CX-2 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 11.1 L (2.5 US gal) | JCB 15W/40 Multigrade (–10 °C to 50 °C / 14 °F to 122 °F); JCB Super Universal Agricultural (–15 °C to 30 °C / 5 °F to 86 °F) |
| Cooling system | Not documented for this exact serial range — verify with your dealer | Not documented for this exact serial range — verify with your dealer |
| Fuel tank | 83.2 L (18.3 US gal) | Diesel Oil (See Types of Fuel) |
| Transmission | Not documented for this exact serial range — verify with your dealer | JCB Special Transmission Fluid (for machines from serial 320,000); ATF D2 (red) noted in field use |
| Final drives | Not documented for this exact serial range — verify with your dealer | Not documented for this exact serial range — verify with your dealer |
| Hydraulic system AND tank | Not documented for this exact serial range — verify with your dealer | JCB HP46 or ISO 46 hydraulic fluid |
| Axles/differentials | Not documented for this exact serial range — verify with your dealer | JCB HD90 Gear Oil (front axle); JCB Special Gear Oil (rear axle); SUTO 15/40 (suitable for wet brakes) noted for rear axle |
| Grease | Not applicable | Not documented for this exact serial range — verify with your dealer |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Jcb 3CX-2 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 100 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
Servicing the 3CX-2 beyond the schedule
Predictive Maintenance & Fluid Analysis
Baseline fluid analysis at the 500-hour interval is mandatory for the 3CX-2. Sample the engine, hydraulic, front axle, and rear axle systems to detect early wear metals or silicate separation in the coolant. JCB coolant relies on silicate coatings; brown sludge in the expansion tank indicates failure. Monitor hydraulic oil for viscosity changes and fuel dilution. Use JCB High Performance Hydraulic Oil ISO VG46 for temperatures above 38°C (100°F) and HP32 ISO VG32 for lower temperatures. Regular sampling prevents catastrophic pump failure by identifying contamination before it reaches the variable flow pump.
Corrective & Common Repairs
The 3CX-2 DieselMax engine utilizes high-pressure common-rail injection up to 2000 bar. Contaminated fuel is the primary cause of injector failure; ensure the fuel water separator is drained daily and filters are replaced at 500 hours. The transmission uses a wet-disc brake system requiring JCB Super Universal Agricultural oil or equivalent 15W-40 diesel oil meeting API specs. Inspect the slew ring bolts on the rear frame for torque loss. Check the variable geometry turbocharger (VGT) vanes for carbon buildup if power drops. Replace drive belts every 2,000–4,000 hours or upon visible cracking.
Overhaul & Rebuild Points
The 2,000-hour interval marks the start of major component life assessment. Inspect the hydraulic pump swash plate and valve block for wear. Check the transmission torque converter for slippage or overheating signs. The rear slew gearbox has a separate oil sump; drain and refill with 90-weight gear oil to prevent bearing failure. Inspect the front axle reduction hubs for seal leaks. The engine valve clearance must be checked at 2,000 hours and adjusted to specification. Monitor the wet-disc brake packs for wear; replacement typically occurs between 4,000 and 6,000 hours depending on road use.
Seasonal & Environment Servicing
The 3CX-2 operates in temperatures from -20°C to +46°C. In cold weather, use JCB 15W/40 Multigrade oil rated for -10°C to 50°C. Ensure the fuel water separator is drained frequently to prevent ice blockage. In hot climates, switch to JCB HP46 hydraulic oil to maintain viscosity. Check the A/C evaporator and cabin filter at the 2,000-hour service. Inspect the engine coolant silicate levels annually; low silicate leads to liner cavitation. Grease all pivot points more frequently in dusty or abrasive environments to prevent premature bushing wear.
3CX-2 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 32/400101 | Head, Fuel Filter | Fuel system service | Check fitment → |
| 200/44600 | Filter, Assembly, Fuel Sediment | Fuel system service | Check fitment → |
| 01/107400R | Engine, Imperial, 4.236 Nat/Aspirated, Engine, Imperial, 4.236 Nat/Aspirated | Fuel system service | Check fitment → |
| 01/111100R | Engine, Imperial, 4.236 Compensated | Fuel system service | Check fitment → |
| 02/100182 | Pipe, Assembly, Fuel, L/Pump To Filter | Fuel system service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
3CX-2 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| P0400-00 | Exhaust Gas Recirculation (EGR) flow fault | Blocked EGR passage or restricted tube; EGR valve malfunction | Inspect EGR tube for blockage or restriction; clean or replace components as necessary |
| P02A6-00 | Fuel trim for cylinder #4 at maximum limit | Fuel delivery issue or injector performance deviation in cylinder 4 | Clear code and reset computer system; inspect fuel system and injector circuit for cylinder 4 |
| P0087 | Fuel rail/system pressure too low | Fuel filter blockage or fuel pump failure | Check and replace fuel filters; inspect fuel pump operation |
| P0117 | Engine coolant temperature sensor circuit low voltage | Faulty coolant temperature sensor or wiring issue | Inspect sensor connector for corrosion; check wiring harness for damage; test sensor resistance |
| P0521 | Engine oil pressure sensor range/performance issue | Faulty oil pressure sensor or low oil level | Check engine oil level; inspect sensor and wiring; test sensor output with multimeter |
| P2047 | DEF/AdBlue injector circuit open (SCR system fault) | Open circuit in reductant injector wiring or faulty injector | Inspect injector wiring harness and connectors for damage; test injector circuit continuity |
| U0100 | Lost communication with Engine Control Module (ECM) | CAN bus communication failure or ECM power/ground issue | Check battery voltage and ground straps; inspect CAN bus wiring for damage or corrosion |
| 101 | Low transmission clutch pressure detected | Transmission hydraulic pressure loss or sensor fault | Check transmission fluid level and condition; inspect hydraulic lines and pressure sensor |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
3CX-2 attachments & work tools
Loader Buckets
Standard heavy-duty loader buckets are available with capacities ranging from 1.0 to 1.3 cubic meters (1.3 to 1.7 cubic yards) and widths of 2.35 meters (92.5 inches). Some configurations utilize a 6-in-1 shovel design with flip-over forks for dozing, loading, and grading. Bucket widths vary by configuration, with specific heavy-duty options noted at 96 inches (2.44 meters) for enhanced breakout force.
Backhoe Buckets
Standard backhoe buckets are 24 inches (610 mm) wide with a capacity of 0.2 to 0.3 cubic meters (0.26 to 0.39 cubic yards). The backhoe arm features an extending dipper option that provides an extra 1 meter (3.3 feet) of reach and dig depth. Dual-position tipping links allow operators to maximize tearout force or rotation for straight-wall digging.
Augers and Planers
The machine is compatible with auger and planer attachments to enhance capability. These tools utilize the bi-directional auxiliary hydraulic lines available on the 3CX series. Specific sizes are not documented for the 3CX-2 in the provided sources; verify with your dealer for exact diameter options.
Skid Steer Attachments
The 3CX Compact variant is equipped with a skid steer loader quick-hitch to engage skid steer attachments. This allows the machine to function with the versatility of a skid steer loader for tasks such as trenching or material handling. Standard 3CX models do not list this quick-hitch as standard; it is specific to the compact range.
Hydraulic Breakers and Tools
Bi-directional and hammer auxiliary lines are available to support a wider range of attachments, including hydraulic breakers. A handheld tool circuit is available on the 3CX Compact to power water pumps, disc cutters, and handheld breakers. Auxiliary flow rates vary by configuration, with the Compact offering 120 liters per minute (31.7 gallons per minute) and standard models up to 150 liters per minute (39.6 gallons per minute).
Quick Couplers and Mounting
JCB buckets feature a unique hanger pickup style designed to sit flush with the machine when the backhoe arm is retracted. The 3CX Compact includes a factory-fitted skid steer quick-hitch for rapid attachment changes. Standard loader and backhoe buckets use fixed mounting points rather than hydraulic quick couplers.
Safety and Guarding
Machines are certified to meet ROPS and FOPS compliance standards. LED lights are fitted as standard to provide optimum visibility at night. The cab includes a new boom lock cable allowing the operator to safely lock the boom from inside. Immobilizers with programmable numerical keycodes are available to prevent unauthorized use.
All 3CX-2 assemblies by section
Every catalogued assembly group for the Jcb 3CX-2. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
A Attachments
A1-2-3 Shovel, Clam, 6 In 1, 1.1 Cu.Yd.
| 10***06 | Pin, Pivot | 2 |
| 10***32 | Pin, Pivot | 2 |
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 2 |
A1-2-1 Shovel, Clam, 6 In 1, 1.0 Cu.Yd
| 10***06 | Pin, Pivot | 2 |
| 10***32 | Pin, Pivot | 2 |
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 2 |
A1-3-4 Fork Lift, Shovel Mounted, (42")
| 12***02 | Plate | 2 |
| 12***03 | Plate | 1 |
| 13***24 | Bolt | 2 |
A1-2-2 Shovel, Clam, 6 In 1, 1.2 Cu.Yd.
| 10***06 | Pin, Pivot | 2 |
| 10***32 | Pin, Pivot | 2 |
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 2 |
A1-3-2 Fork Lift, Shovel Mounted
| 12***00 | Fork, Lift, -3c/3cx/3d | 1 |
| 12***01 | Gusset | 4 |
| 12***00 | Fork | 2 |
A1-1-2 Bucket, Side Tip R/H
| 98***66 | Bucket, Lh Side Tip | 1 |
| 98***99 | Plate | 1 |
| 98***00 | Frame | 1 |
A1-4-1 Crane Hook
| 10***23 | Pin, Pivot | 1 |
| 11***00 | Pin, Lynch, With Chain | 1 |
| 12***39 | Attachment, Crane Hook Assembly, Fork Mounted | 1 |
A1-3-3 Fork Lift, 6 In 1 Clam Shovel, Mounted (42")
| 12***00 | Fork, Shovel Mounted | 1 |
| 12***00 | Fork | 2 |
| 12***00 | Bracket | 2 |
A1-3-1 Fork Lift, Shovel Mounted
| 12***00 | Kit-Fork Lift, Shovel, Std | 1 |
| 12***00 | Fork | 4 |
| 12***01 | Gusset, Standard Shovel | 2 |
A1-1-3 Bucket, Side Tip L/H
| 98***66 | Bucket, Lh Side Tip | 1 |
| 98***99 | Plate | 1 |
| 98***00 | Frame | 1 |
A1-1-1 Shovel
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 2 |
| 10***32 | Pin, Pivot | 2 |
| 10***18 | Spacer | 4 |
A2-3-1 Blade, Ditch Cleaning
| 13***12 | Bolt | 3 |
| 13***2Z | Bolt | 3 |
| 13***1Z | Nut | 0 |
A2-4-2 Bucket, Jaw, 305mm Wide
| 10***18 | Pin, Pivot | 1 |
| 10***19 | Pin, Pivot | 1 |
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 1 |
A2-5-1 Attachments, Jaw Bucket
| 10***48 | Pin, Pivot | 1 |
| 13***14 | Bolt | 6 |
| 13***4Z | Bolt, 3/8"Unf X 2" | 6 |
A2-4-1 Bucket, Jaw, 460mm Wide, Jaw, 600mm Wide
| 10***18 | Pin, Pivot | 1 |
| 10***19 | Pin, Pivot | 2 |
| 10***53 | Pin, Pivot; See Note 1. Fit/Funct M/C M585376, Pin, Pivot | 1 |
A2-1-1 Bucket
| 10***04 | Boss, Pivot | 4 |
| 13***14 | Bolt | 6 |
| 13***4Z | Bolt | 6 |
A2-1-2 Bucket
| 10***04 | Boss, Pivot | 4 |
| 13***14 | Bolt | 6 |
| 13***4Z | Bolt | 6 |
A2-2-1 Attachments, Backhoe, Ripper Tooth,B.Blade, Bucket,Clay,Square Hole,T.Ditching
| 10***56 | Pin, Pivot | 3 |
| 10***00 | Lever | 1 |
| 10***00 | Link | 1 |
A3-3-1 Roadbreaker, Stanley
| 12***00 | Breaker, Road | 1 |
| 12***01 | Handle | 1 |
| 12***02 | Grab | 1 |
A3-1-2 Roadbreaker, Installation, 4wd
| 10***06 | Lock; Supply 12***71 | 1 |
| 11***09 | Washer | 3 |
| 12***00 | Pipe | 1 |
A3-2-1 Roadbreaker, Hose Reel
| 12***01 | Plate, Side | 2 |
| 12***02 | Plate | 1 |
| 12***03 | Block | 1 |
A3-1-1 Roadbreaker, Installation, 2wd
| 10***06 | Lock; Supply 12***71 | 1 |
| 12***00 | Carrier | 1 |
| 12***00 | Carrier | 1 |
A3-4-1 Roadbreaker, Steels, Stanley
| 99***14 | Pad, Rammer | 1 |
| 99***15 | Tool, Moil, Tool, Moil; 380mm Long Below Collar. 160mm (6 1/4") Long Above Collar | 1 |
| 99***16 | Tool, Chisel, Narrow | 1 |
A3-5-4 Breaker, Brh 250
| 12***87 | Bracket, Carrier | 1 |
| 16***18 | Adapter | 1 |
| 81***44 | Adapter | 1 |
A3-5-3 Breaker, Brh 125
| 90***00 | Breaker, Hydraulic | 1 |
| 90***01 | Screw | 10 |
| 90***02 | Accumulator, Assembly | 1 |
A3-5-2 Breaker, Brh 125, With Side Plates, Standard
| 10***51 | Spacer | 2 |
| 12***00 | Kit-Installation, Brh125 Breaker | 1 |
| 12***00 | Plate, Side; Part Is Mss Use The Following Parts 12***54, 1 Off, 12***55 1 Off., Plate, Side; Part Is Mss Use The Following Parts 12***54, 1 Off, 12***55 1 Off., For Use On Normal Backhoe. Part Is Mss Use The Following Parts Marked B , Ie 1 Left Hand, 1 Right Hand Plate. | 1 |
A3-5-1 Powerbreaker
| 12***00 | Breaker, Power | 1 |
| 12***01 | Plate | 1 |
| 12***00 | Plate, Pivot | 1 |
A3-6-1 Powerbreaker Steels, Krupp
| 99***06 | Shaft | 1 |
| 99***07 | Pad, Pile Driving | 1 |
| 99***08 | Sleeve, Pile Driving | 1 |
A4-2-1 Highway Parts, Italian
| 12***00 | Strut, Jury | 1 |
| 12***00 | Strap | 1 |
| 12***01 | Washer | 2 |
A4-1-1 Tooth Guard
| 10***00 | Guard, Tooth | 1 |
| 11***00 | Cable, Control, With Plug | 1 |
| 12***00 | Guard, Tooth | 1 |
A4-3-1 Front Mudguard, Swedish
| 12***01 | Guard, Mud | 2 |
| 12***02 | Strap | 4 |
| 12***00 | Platform, Lh | 1 |
B Bodywork, Cab, Loader End
B1-4-2 Stabiliser, Centremount
| 10***04 | Collar | 2 |
| 12***00 | Leg, Stabiliser | 2 |
| 12***00 | Leg, Stabiliser, Lh | 1 |
B1-1-3 Mainframe, Centremount
| 11***09 | Washer | 8 |
| 12***00 | Grille | 1 |
| 12***02 | Guard, Mesh | 1 |
B1-1-4 Mainframe, Loader
| 11***09 | Washer | 4 |
| 11***00 | Pin, Lynch, With Chain | 1 |
| 12***00 | Grille | 1 |
B1-1-6 Mainframe, 8'0" Sideshift, German, Swedish
| 11***09 | Washer | 8 |
| 12***00 | Leg, Outer, Right Hand | 1 |
| 12***00 | Grille | 1 |
B1-1-2 Mainframe, 8'0" Sideshift
| 11***09 | Washer | 8 |
| 12***00 | Leg, Outer, Right Hand | 1 |
| 12***00 | Grille | 1 |
B1-3-1 Tank, Diesel Fuel, Fittings
| 10***06 | Lock; Supply 12***71 | 1 |
| 12***00 | Cap, Filler | 1 |
| 12***00 | Tube, Filler | 1 |
B1-1-5 Mainframe, 7'4" Sideshift, German, Swedish
| 11***09 | Washer | 8 |
| 12***00 | Leg, Outer, Right Hand | 1 |
| 12***00 | Grille | 1 |
B1-4-3 Stabiliser, Centremount
| 10***30 | Pin, Pivot | 2 |
| 10***04 | Collar | 2 |
| 12***01 | Foot, Rubber | 2 |
B1-5-1 Bonnet
| 12***00 | Hinge, Assemble | 2 |
| 12***00 | Stay | 1 |
| 12***00 | Stay, Assembly | 1 |
B1-2-1 Tank, Hydraulic, Fitting
| 12***03 | Indicator | 1 |
| 12***05 | Indicator | 1 |
| 12***00 | Cover | 1 |
B1-1-7 Mainframe, Centremount
| 12***00 | Grille | 1 |
| 12***02 | Guard, Mesh | 1 |
| 12***04 | Spacer | 4 |
B1-4-1 Stabiliser, Sideshift
| 10***10 | Pin, Pivot | 1 |
| 10***37 | Pin, Pivot | 2 |
| 10***02 | Foot; Replaced By 12***66, See San04389 | 4 |
B1-1-1 Mainframe, 7'4" Sideshift
| 10***06 | Spacer | 1 |
| 10***19 | Boss | 1 |
| 11***09 | Washer | 8 |
B2-3-2 Canopy
| 10***00 | Mirror, Interior; Cwe By 12***71 - See San 10750 | 1 |
| 12***00 | Mirror | 2 |
| 12***01 | Bracket | 1 |
B2-2-3 Cab Glazing, Swedish
| 10***00 | Mirror, Interior; Cwe By 12***71 - See San 10750 | 1 |
| 12***00 | Mirror | 2 |
| 12***01 | Bracket | 2 |
B2-3-3 Cab
| 12***01 | Bracket, Interior Light | 1 |
| 12***02 | Cap | 4 |
| 12***05 | Bolt, Closing | 1 |
B2-2-1 Cab Glazing
| 10***00 | Mirror, Interior; Cwe By 12***71 - See San 10750 | 1 |
| 12***00 | Cab, Assembly, With Glass | 1 |
| 12***00 | Cab, Assembly, With Glass | 1 |
B2-3-1 Cab Shell, Unglazed
| 12***00 | Roof, Swedish | 1 |
| 12***00 | Door, Lh | 1 |
| 12***00 | Door, Rh | 1 |
B2-5-3 Basic Seat
| 12***10 | Cushion, Brown, Vinyl | 1 |
| 12***11 | Cushion, Brown, Vinyl | 1 |
| 12***00 | Lever | 1 |
B2-3-4 Cab -, Swedish
| 12***01 | Bracket, Interior Light | 1 |
| 12***02 | Cap | 4 |
| 12***05 | Bolt, Closing | 2 |
B2-6-2 Soundproofing, Engine - Swedish
| 12***01 | Mat | 2 |
| 12***02 | Mat | 2 |
| 12***01 | Lug | 2 |
B2-2-2 Cab Glass
| 10***00 | Mirror, Interior; Cwe By 12***71 - See San 10750 | 1 |
| 12***00 | Mirror | 1 |
| 12***01 | Bracket | 1 |
B2-4-1 Wash/Wipe, Windscreen
| 12***00 | Pump, And Reservoir | 1 |
| 12***01 | Jet | 1 |
| 12***00 | Pump, And Reservoir | 1 |
B2-5-2 9802/8000 B2-5-2
| 11***01 | Stop | 1 |
| 11***00 | Lever | 1 |
| 12***01 | Adapter | 1 |
B2-6-1 Soundproofing, Engine
| 12***00 | Panel, Engine, Lh | 1 |
| 12***00 | Panel, Engine, Rh | 1 |
| 12***01 | Mat | 2 |
B2-5-1 Basic Seat
| 12***00 | Housing | 1 |
| 12***00 | Riser, Seat, Assembly | 1 |
| 12***03 | Cushion | 1 |
B2-5-6 Seat Riser, Standard, German, Swedish, Optional, Uk & World
| 40***01 | Damper | 1 |
| 40***10 | Bracket | 1 |
| 40***11 | Lever | 1 |
B2-5-4 Seat - Optional, Swedish/German,U.K., & World
| 12***00 | Seat, Complete, Low Back | 1 |
| 12***00 | Seat | 1 |
| 40***00 | Seat, Suspension, Fabric | 2 |
B2-1-1 Soundproofing, Cab Base
| 12***02 | Plate, Compression | 8 |
| 12***03 | Mounting, Cab, Rubber; Use 26***05, San 04452 | 4 |
| 12***02 | Mat | 1 |
B2-5-5 Seat With Riser, Standard, German, Swedish, Optional, Uk & World
| 12***00 | Seat, Complete, Low Back | 1 |
| 12***14 | Spacer | 2 |
| 13***6Z | Bolt, Bolt; See Index B3 For Sideshift Arrangement. Refer To Index B3 For Sideshift Arrangement. | 4 |
B2-9-1 Window, Rear, Swedish
| 12***01 | Handle, Right Hand, (M6) | 1 |
| 12***02 | Handle, Left Hand | 1 |
| 12***00 | Handle | 1 |
B3-2-1 Arms, Loader, Parallel Lift
| 10***15 | Pin, Pivot, 165mm Long | 2 |
| 10***21 | Pin, Pivot | 2 |
| 10***26 | Pin, Pivot | 8 |
B3-1-1 Arms, Loader, Basic
| 10***15 | Pin, Pivot, 165mm Long | 4 |
| 10***21 | Pin, Pivot | 2 |
| 10***26 | Pin, Pivot | 6 |
B4-1-1 Kingpost Carriage, Sideshift
| 12***05 | Pin, Lock | 1 |
| 12***07 | Plate | 1 |
| 12***13 | Shaft | 1 |
B4-5-2 Dipper (Stick), Standard
| 10***47 | Pin, Pivot | 1 |
| 10***59 | Pin, Pivot | 1 |
| 10***33 | Pin, Pivot | 1 |
B4-1-3 Kingpost Carriage, Centremount
| 12***05 | Pin, Lock | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Carriage | 1 |
B4-3-2 Kingpost
| 10***16 | Pin, Pivot | 1 |
| 11***01 | Collar | 1 |
| 12***09 | Breather | 1 |
B4-4-2 Boom
| 10***32 | Pin, Pivot | 1 |
| 10***30 | Pin, Pivot | 1 |
| 10***01 | Adapter | 1 |
B4-2-1 Slew/Swing, Components
| 12***03 | Pin | 1 |
| 12***06 | Bearing | 1 |
| 12***12 | Gear, Pinion | 1 |
B4-1-2 Kingpost Carriage, Centremount
| 12***05 | Pin, Lock | 1 |
| 12***13 | Shaft | 1 |
| 12***20 | Carriage | 1 |
B4-4-4 Boom
| 10***23 | Pin, Pivot | 1 |
| 10***40 | Pin, Pivot | 1 |
| 12***00 | Boom, 2200 M.M. Long | 1 |
B4-3-1 Kingpost
| 10***16 | Pin, Pivot | 1 |
| 10***01 | Collar | 1 |
| 12***09 | Breather | 1 |
B4-6-2 Dipper (Stick), Extending
| 10***32 | Pin, Pivot | 1 |
| 10***40 | Pin, Pivot | 1 |
| 10***59 | Pin, Pivot | 1 |
B4-5-1 Dipper (Stick), Standard
| 10***47 | Pin, Pivot | 1 |
| 10***59 | Pin, Pivot | 1 |
| 10***33 | Pin, Pivot | 1 |
B4-4-3 Boom
| 10***16 | Pin, Pivot | 1 |
| 10***30 | Pin, Pivot | 1 |
| 10***01 | Adapter | 1 |
B4-5-3 Dipper (Stick), Standard
| 10***47 | Pin, Pivot | 1 |
| 10***59 | Pin, Pivot | 1 |
| 10***43 | Pin, Pivot | 1 |
B4-2-2 Slew/Swing, Components
| 12***06 | Bearing | 1 |
| 12***14 | Rack | 1 |
| 12***00 | Plate | 1 |
B4-4-1 Boom
| 10***32 | Pin, Pivot | 1 |
| 10***30 | Pin, Pivot | 1 |
| 10***01 | Adapter | 1 |
B4-6-1 Dipper (Stick), Extending
| 10***25 | Pin, Pivot | 1 |
| 10***40 | Pin, Pivot | 1 |
| 10***59 | Pin, Pivot | 1 |
B5-2-1 Tool Kit, Standard
| 27***00 | Bag, Tool | 1 |
| 82***02 | Spanner, 7/16" X 1/2" A/F | 1 |
| 82***04 | Spanner, Doe, 9/16" X 5/8" A/F | 1 |
B5-4-1 Fire Extinguisher
| 13***02 | Nut | 2 |
| 14***05 | Screw, Self Tapping | 2 |
| 25***00 | Extinguisher, Fire | 1 |
B5-1-1 Paint And Transfers
| 12***02 | Decal, Jcb, Side Door | 2 |
| 42***04 | Paint, Black Gloss Enamel, 1 Lts | 0 |
| 42***04 | Paint, Gloss Yellow, 1 Lts | 0 |
B5-3-1 Tool Kit, Supplementary
| 82***02 | Spanner, 7/16" X 1/2" A/F | 1 |
| 82***04 | Spanner, Doe, 9/16" X 5/8" A/F | 1 |
| 82***05 | Spanner, 11/16" X 3/4" A/F, D.O.E. | 1 |
C Electrics-Machine, Cab & Engine
C1-4-1 Light, Side, Shovel Mounted, German & Swiss
| 12***00 | Bracket | 1 |
| 12***01 | Bracket, Swiss | 2 |
| 12***02 | Bracket, Reflector Mounting, German | 2 |
C1-3-1 Light, Head, Working
| 12***00 | Bracket | 2 |
| 13***4Z | Bolt | 2 |
| 13***3Z | Nut, 5/16" Unf | 2 |
C1-1-1 Electrical Equipment, Cab
| 12***01 | Cover, Front | 1 |
| 12***02 | Cover, Rear | 1 |
| 12***01 | Bracket | 2 |
C1-4-2 Light, Side, Shovel Mounted, German & Swiss
| 12***01 | Bracket, Swiss | 1 |
| 12***02 | Bracket, Reflector Mounting, German | 1 |
| 12***00 | Bracket | 1 |
C1-3-2 Light, Head, Working
| 70***01 | Bulb, 12v 55w, Halogen | 1 |
| 70***03 | Spring | 1 |
| 70***00 | Light, Working, 12 Volt | 2 |
C1-2-2 Side & Rear Lights
| 10***01 | Spring, 24" Bungy | 1 |
| 12***00 | Bracket, Rh | 1 |
| 12***00 | Bracket, Lh | 1 |
C1-5-1 Pump, Diesel, Refuelling
| 12***00 | Kit-Refuelling Pump; Replaced By 12***01, 12***02, 64***01,, 70***01 | 1 |
| 12***01 | Pump, 12v,Refuel | 1 |
| 12***02 | Diesel Pump Bag | 1 |
C1-2-1 Side & Rear Lights
| 10***01 | Spring, 24" Bungy | 1 |
| 70***00 | Light, Rear Fog | 1 |
| 70***00 | Light, Side Front, Supplied Without Bulbs | 2 |
C2-5-4 Motor, Starter, M127 12.Volt, 4.236 Engines
| 12***06 | Cover, Solenoid | 1 |
| 12***03 | Tie, Cable, L=300mm X W=7.6mm | 1 |
| 13***1Z | Nut | 3 |
C2-6-2 Heater, Installation, Swedish
| 11***03 | Tap | 1 |
| 12***01 | Strap | 1 |
| 12***03 | Elbow; Nsp, See San 11129 | 1 |
C2-6-3 Heater, Installation
| 11***03 | Tap | 1 |
| 12***01 | Strap | 1 |
| 12***03 | Elbow; Nsp, See San 11129 | 1 |
C2-1-1 Electrics, Engine
| 02***23 | Switch, Oil Pressure | 1 |
| 04***76 | Switch, Isolating | 1 |
| 04***99 | Switch, Neutral Start | 1 |
C2-4-2 Alternator
| 71***06 | Kit-Bearing, Drive End | 1 |
| 71***00 | Alternator; Lucas Ref 24037. Type Of Alternator Best Identified By Lucas Ref.Stamped On Body., Alternator; Lucas Ref.24037. Type Of Alternator Best Identified By Lucas Ref,Stamped On Body., Alternator; Lucas Ref.24037. Type Of Alternator Best Identified By Lucas Ref. Stamped On Tag At Pulley End., Alternator; Lucas Ref. 24037. Type Of Alternator Best Identified By Lucas Ref,Stamped On Body., Alternator; Lucas Ref.24037. Type Of Alternator Best Identified By Lucas Ref Stamped On Body., Alternator | 1 |
| 71***01 | Cover | 1 |
C2-6-4 Heater, Installation, Swedish
| 11***03 | Tap | 1 |
| 12***01 | Strap | 1 |
| 12***03 | Elbow; Nsp, See San 11129 | 1 |
C2-5-1 Motor, Starter
| 12***06 | Cover, Solenoid | 1 |
| 12***03 | Tie, Cable, L=300mm X W=7.6mm | 1 |
| 70***01 | Bracket, Commutator End | 1 |
C2-8-1 Installation, Reverse Alarm, Optional
| 13***02 | Nut, Lock | 1 |
| 14***14 | Washer, Star | 1 |
| 70***00 | Switch | 1 |
C2-3-2 Alternator Mountings, 4.236 Engine
| 02***73 | Bracket, Alternator Mounting | 1 |
| 02***74 | Bracket, Alternator Support | 1 |
| 02***75 | Lever, Alternator Adjusting | 1 |
C2-3-1 Alternator Mountings, 4.98nt Engine
| 02***88 | Bracket, Support | 1 |
| 02***89 | Tube, Spacer | 1 |
| 02***90 | Link, Adjusting | 1 |
C2-4-4 Alternator, A127-45amp 12.Volt, 4.236 Engines
| 71***01 | Capacitor, Suppression | 1 |
| 71***02 | Regulator, & Brush Box Assembly | 1 |
| 71***03 | Bracket, Slip Ring End | 1 |
C2-1-2 Electrics, Engine, Swedish
| 02***23 | Switch, Oil Pressure | 1 |
| 04***76 | Switch, Isolating | 1 |
| 04***99 | Switch, Neutral Start | 1 |
C2-3-4 Alternator Mountings
| 02***76 | Spacer | 1 |
| 02***01 | Lever, Alternator Adjusting | 1 |
| 02***02 | Bracket, Alternator Mounting | 1 |
C2-3-3 Alternator Mountings
| 02***76 | Spacer | 1 |
| 02***92 | Washer | 3 |
| 02***43 | Bracket, Alternator Mounting | 1 |
C2-7-1 Warning System -, Powerbreaker
| 14***19 | Seal, Dowty | 1 |
| 24***12 | Grommet | 1 |
| 70***00 | Light, Warning | 1 |
C2-6-1 Heater, Installation
| 11***03 | Tap | 1 |
| 12***01 | Strap | 1 |
| 12***03 | Elbow; Nsp, See San 11129 | 1 |
C2-4-3 Alternator, A127-45amp 12.Volt, Blmc 4.98 Engines
| 71***01 | Capacitor, Suppression | 1 |
| 71***02 | Regulator, & Brush Box Assembly | 1 |
| 71***03 | Bracket, Slip Ring End | 1 |
C2-5-5 Motor, Starter, M127 12.Volt, 4.236 Engines
| 02***02 | Stud | 3 |
| 02***59 | Nut | 3 |
| 12***06 | Cover, Solenoid | 1 |
C2-4-1 Alternator
| 02***28 | Pulley | 1 |
| 71***01 | Regulator | 1 |
| 71***02 | Rotor, Assembly | 1 |
C2-5-3 Starter Motor, Type M127 - 12.Volt, Blmc 4.98 Engines, (Alternative)
| 12***06 | Cover, Solenoid | 1 |
| 12***03 | Tie, Cable, L=300mm X W=7.6mm | 1 |
| 13***6Z | Bolt | 3 |
C2-2-1 Battery 12v, Carrier, Standard
| 10***00 | Clamp | 1 |
| 12***01 | Tray | 1 |
| 12***02 | Tray | 1 |
C2-5-2 Motor, Starter, Service Option
| 71***00 | Motor, Starter | 1 |
| 71***01 | Bearing | 1 |
| 71***02 | Bracket, End | 1 |
C3-1-1 Switch, Column
| 11***01 | Key, German | 2 |
| 12***09 | Cover | 1 |
| 12***12 | Cover | 1 |
C3-2-1 Instrument Panel
| 12***03 | Cover | 1 |
| 12***04 | Bracket | 1 |
| 12***06 | Cover | 1 |
C3-2-2 Instrument Panel
| 12***05 | Cover | 1 |
| 12***06 | Cover | 1 |
| 12***00 | Cable, Control | 1 |
D Controls-Machine, Engine
D1-2-4 Controls, Excavator, Swedish
| 10***01 | Knob, Large Dia. | 2 |
| 10***06 | Joint, Ball | 2 |
| 12***02 | Band, Retaining | 1 |
D1-2-3 Controls, Excavator, Standard
| 10***01 | Knob, Large Dia. | 2 |
| 10***06 | Joint, Ball | 2 |
| 12***02 | Band, Retaining | 1 |
D1-3-1 Foot Pedal Controls, - Aux. Valve
| 12***00 | Lever | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Bracket | 1 |
D1-1-2 Controls, Loader Valve, With Lever Lock
| 10***01 | Knob, Large Dia. | 1 |
| 10***05 | Joint, Universal | 2 |
| 10***06 | Joint, Ball | 1 |
D1-1-1 Controls, Loader Valve
| 10***01 | Knob, Large Dia. | 1 |
| 10***05 | Joint, Universal | 2 |
| 10***06 | Joint, Ball | 1 |
D1-3-2 Foot Pedal Controls, - Aux. Valve
| 12***00 | Lever | 1 |
| 12***00 | Bracket | 1 |
| 12***01 | Bar, Locking | 1 |
D1-1-4 Controls, Loader Valve, With Lever Lock
| 10***01 | Knob, Large Dia. | 1 |
| 10***06 | Joint, Ball | 1 |
| 12***01 | Rod | 1 |
D1-4-1 Installation, Shovel Reset
| 12***00 | Bracket | 1 |
| 12***01 | Bar | 1 |
| 12***02 | Bracket, Saddle | 2 |
D1-2-2 Controls, Excavator, Swedish
| 10***01 | Knob, Large Dia. | 2 |
| 10***05 | Joint, Universal | 1 |
| 10***06 | Joint, Ball | 1 |
D1-1-3 Controls, Loader Valve
| 10***01 | Knob, Large Dia. | 1 |
| 10***06 | Joint, Ball | 1 |
| 12***01 | Rod | 1 |
D1-2-1 Controls, Excavator, Standard
| 10***01 | Knob, Large Dia. | 2 |
| 10***05 | Joint, Universal | 1 |
| 10***06 | Joint, Ball | 1 |
D1-5-1 Lever Lock, Excavator Valve, Italian Build
| 12***00 | Kit-Lever Lock | 1 |
| 12***01 | Plate, Lock | 1 |
| 12***02 | Pin, Pivot | 1 |
D1-3-3 Foot Pedal Controls, - Aux. Valve
| 12***01 | Bar, Locking | 1 |
| 12***02 | Plate | 1 |
| 12***00 | Bracket | 1 |
D2-2-1 Control, Parking Brake
| 12***05 | Bracket | 1 |
| 12***01 | Plate | 1 |
| 12***02 | Plate | 1 |
D2-1-1 Control Pedal, Brake
| 10***01 | Knob, Large Dia. | 1 |
| 12***04 | Pin, Pivot | 1 |
| 12***06 | Plate, Lock | 1 |
D3-1-1 Throttle Controls, Blmc 4.98 Engine
| 02***82 | Spring | 1 |
| 10***00 | Bracket | 1 |
| 10***01 | Bracket | 1 |
D3-1-4 Throttle Controls, 4.236 Engine, Swedish Builds
| 02***83 | Spring, Stop/Return | 1 |
| 02***84 | Spring, Throttle Return | 1 |
| 10***01 | Connector | 1 |
D3-1-3 Throttle Controls, 4.236 Engine
| 02***83 | Spring, Stop/Return | 1 |
| 02***84 | Spring, Throttle Return | 1 |
| 12***00 | Pedal, Throtle Control | 1 |
D3-1-2 Throttle Controls, Blmc 4.98 Engines, Swedish Builds
| 02***82 | Spring | 1 |
| 10***01 | Connector | 1 |
| 10***00 | Bracket | 1 |
D3-2-1 Controls, Forward & Reverse, Transmission Dump
| 12***05 | Pin, Pivot | 1 |
| 12***00 | Pedal | 1 |
| 12***1P | Bracket | 1 |
D3-2-2 Controls, Forward & Reverse, Transmission Dump, 2/4wd Selector
| 12***00 | Pedal | 1 |
| 12***01 | Bracket | 1 |
| 12***02 | Bracket | 1 |
E Hydraulics
E1-4-2 Circuit, Excavator, Valve To Kingpost, Iso Controls
| 12***00 | Cluster, Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Base | 1 |
E1-5-4 Circuit, Backhoe, Standard Dipper, Centremount/7
| 12***00 | Pipe | 1 |
| 13***03 | Nut | 3 |
| 61***00 | Hose | 2 |
E1-9-3 Circuit, Auxiliary, Hydraulic Breaker
| 14***11 | Seal, Bonded | 1 |
| 14***14 | Washer, Seal | 1 |
| 14***17 | Seal | 7 |
E1-3-5 Circuit, Pole Planter, Installation
| 12***01 | Manifold | 1 |
| 12***02 | Bracket | 1 |
| 12***03 | Connector | 1 |
E1-6-5 Auxiliary Circuit, Powerbreaker
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***01 | Plate | 1 |
E1-3-2 Circuit, Auxiliary, Loader Arm, Self Level
| 12***02 | Plate | 2 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-4-6 Circuit, Excavator, Valve To Kingpost, Iso Controls
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-1-4 Circuit, Roadbreaker
| 12***02 | Plate | 2 |
| 12***00 | Pipe | 1 |
| 12***00 | Bracket | 1 |
E1-6-7 Auxiliary Circuit, Hose And Pipework, Powerbreaker (Krupp)
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***01 | Plate | 1 |
E1-7-1 Circuit, Hydraclamp, Sideshift
| 12***05 | Pin, Lock | 4 |
| 12***05 | Seal | 1 |
| 12***01 | Housing | 4 |
E1-6-1 Circuit, Auxiliary, Backhoe, Standard Dipper, Sideshift
| 12***07 | Guide | 2 |
| 12***00 | Pipe, Assembly | 1 |
| 12***00 | Pipe | 1 |
E1-8-4 Circuit, Backhoe, Extradig Dipper, Centremount 1550/1900
| 12***00 | Pipe | 2 |
| 12***00 | Pipe | 1 |
| 13***04 | Bolt | 2 |
E1-2-2 Circuit, Loader Arm, Self Level
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 13***08 | Bolt | 6 |
E1-7-2 Circuit, Hydraclamp, Sideshift
| 12***05 | Pin, Lock | 4 |
| 12***01 | Housing | 4 |
| 12***00 | Bracket, Support | 1 |
E1-6-9 Circuit, Auxiliary, Backhoe, Standard Dipper, Sideshift/7
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***01 | Plate | 1 |
E1-6-6 Auxiliary Circuit, Powerbreaker
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***01 | Plate | 1 |
E1-4-1 Circuit, Excavator, Valve To Kingpost, Iso Controls
| 12***00 | Cluster, Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Base | 1 |
E1-1-1 Circuit, Neutral, Single Pump
| 12***00 | Pipe | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Pipe | 1 |
E1-6-3 Circuit, Auxiliary, Backhoe, Standard Dipper, Centermount
| 12***07 | Guide | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-2-4 Hose And Pipework, Loader Arm, Self Level
| 12***00 | Pipe, Assembly | 1 |
| 13***08 | Bolt | 2 |
| 13***03 | Nut | 2 |
E1-3-4 Circuit, Auxiliary, Loader Arm, Self Level
| 13***08 | Bolt | 2 |
| 13***12 | Bolt | 1 |
| 14***03 | Washer | 3 |
E1-9-2 Circuit, Auxiliary, Breaker Brh125, Standard Dipper
| 12***02 | Guide | 2 |
| 12***01 | Plate | 1 |
| 12***02 | Guide | 1 |
E1-5-1 Circuit, Backhoe, Standard Dipper, Sideshift
| 12***00 | Pipe | 1 |
| 13***03 | Nut | 2 |
| 61***00 | Hose | 2 |
E1-1-3 Neutral Circuit, Loading Shovel
| 12***00 | Pipe | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Pipe | 1 |
E1-2-3 Circuit, Loader Arm, Basic
| 12***00 | Pipe, Assembly | 1 |
| 13***8Z | Bolt | 2 |
| 13***8Z | Bolt | 4 |
E1-5-2 Circuit, Backhoe, Standard Dipper, Sideshift
| 12***00 | Pipe | 1 |
| 13***03 | Nut | 1 |
| 61***00 | Hose, 1/4"Bsp X 1200mm | 2 |
E1-4-7 Circuit, Excavator, Valve To Kingpost, Jcb Controls
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-6-2 Circuit, Auxiliary, Backhoe, Standard Dipper, Sideshift
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-4-5 Circuit, Excavator, Valve To Kingpost, Iso Controls
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-3-1 Circuit, Auxiliary, Loader Arm, Basic
| 12***02 | Plate | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-6-8 Hose And Pipework, Aux. Circuit, Powerbreaker
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***01 | Plate | 1 |
E1-4-4 Circuit, Excavator, Valve To Kingpost, Jcb Controls
| 12***00 | Cluster, Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Base | 1 |
E1-8-2 Circuit, Backhoe, Extradig Dipper, Sideshift
| 12***00 | Pipe | 2 |
| 12***00 | Pipe | 1 |
| 12***00 | Clamp, Base, Standard & Auxiliary. | 1 |
E1-1-5 Neutral Circuit, Auxiliary Valve, Powerbreaker
| 13***05 | Bolt | 3 |
| 14***19 | Seal, Dowty | 1 |
| 14***26 | Washer, Seal | 2 |
E1-5-3 Circuit, Backhoe, Standard Dipper, Centremount
| 12***00 | Pipe | 1 |
| 12***00 | Hose | 1 |
| 13***03 | Nut | 2 |
E1-1-2 Circuit, Neutral, Twin Pump
| 12***00 | Pipe | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Pipe | 1 |
E1-8-1 Circuit, Backhoe, Extradig Dipper, Sideshift
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 2 |
| 12***00 | Clamp, Base, Standard & Auxiliary. | 1 |
E1-9-1 Circuit, Auxiliary, Breaker Brh125, Standard Dipper
| 12***02 | Guide | 2 |
| 12***01 | Plate | 1 |
| 12***02 | Guide | 1 |
E1-6-4 Circuit, Auxiliary, Backhoe, Standard Dipper, Centermount
| 12***07 | Guide | 2 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-8-3 Circuit, Backhoe, Extradig Dipper, Centremount 1400/1600
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 2 |
| 12***00 | Pipe, Rh | 2 |
E1-4-8 Circuit, Excavator, Valve To Kingpost, Jcb Controls
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
E1-3-3 Circuit, Auxiliary, Loader Arm, Basic
| 13***12 | Bolt | 1 |
| 14***03 | Washer | 1 |
| 14***06 | Washer | 1 |
E1-2-1 Circuit, Loader Arm, Basic
| 12***00 | Pipe | 1 |
| 12***00 | Pipe | 1 |
| 13***14 | Bolt, Long | 4 |
E1-8-5 Hose & Pipework, Extended Dipper, Centremount Circuit
| 12***00 | Pipe, R.H | 1 |
| 12***00 | Pipe, L.H. | 1 |
| 12***00 | Pipe | 1 |
E1-5-5 Circuit, Backhoe, Standard Dipper, Centremount/7
| 12***00 | Pipe | 1 |
| 13***04 | Bolt | 2 |
| 13***03 | Nut | 1 |
E1-4-3 Circuit, Excavator, Valve To Kingpost, Jcb Controls
| 12***00 | Cluster, Pipe | 1 |
| 12***00 | Pipe | 1 |
| 12***00 | Base | 1 |
E2-2-1 Pump, Main Hydraulic, Double, Standard, Extradig Dipper, Optional, Auxiliary
| 13***10 | Bolt | 4 |
| 13***14 | Bolt | 2 |
| 13***03 | Nut | 2 |
E2-3-1 Shaft, Pump Drive
| 11***02 | Adapter, Drive | 1 |
| 12***02 | Adapter, Drive | 1 |
| 13***06 | Bolt | 4 |
E2-1-1 Pump, Main Hydraulic, Single, Standard
| 13***10 | Bolt | 4 |
| 13***03 | Nut | 2 |
| 14***21 | Seal, Bonded 3/4" Bsp | 1 |
E3-6-3 Valve, Section, Excavator Valve, Seventh Spool
| 24***15 | O Ring | 1 |
| 24***11 | O Ring | 1 |
| 91***00 | Valve, Section, Assembly | 1 |
E3-1-1 Valve, Loader
| 12***01 | Mounting, Rubber | 3 |
| 13***30 | Bolt | 1 |
| 13***03 | Nut | 6 |
E3-5-2 Valve, Assembly, Excavator, Sideshift
| 12***00 | Restrictor | 2 |
| 13***34 | Bolt | 2 |
| 13***03 | Nut | 1 |
E3-6-1 Valve, Components, Excavator
| 13***06 | Bolt | 12 |
| 24***14 | O Ring | 1 |
| 24***04 | O Ring | 1 |
E3-7-1 Filter, Hydraulic
| 13***01 | Plug, Drain | 1 |
| 13***01 | Nut | 2 |
| 14***11 | Seal, Bonded | 1 |
E3-6-2 Valve, Components, Excavator
| 24***07 | O Ring | 12 |
| 24***17 | O Ring | 7 |
| 92***22 | Seal, Wiper | 6 |
E3-7-2 Filter -, Powerbreaker
| 32***00 | Filter | 1 |
| 32***01 | Element | 1 |
| 32***02 | Seal | 1 |
E3-6-4 Valve, Rotary Clamp
| 14***11 | Seal, Bonded | 1 |
| 24***15 | O Ring | 1 |
| 92***54 | O Ring | 1 |
E3-8-1 Lubricants & Filters
| 02***73 | Element, Oil Filter, Canister Type - Long | 1 |
| 02***84 | Element, Oil Filter, Canister Type-Short | 1 |
| 02***17 | Element, Spin-On Canister | 1 |
E3-2-2 Valve, Relief, Check & Overload, Loader Valve
| 13***02 | Nut | 1 |
| 24***07 | O Ring | 1 |
| 24***11 | O Ring | 2 |
E3-5-1 Valve, Assembly, Excavator, Centremount
| 13***34 | Bolt | 1 |
| 13***01 | Nut | 2 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 12 |
E3-2-1 Loader Valve M.R.V.
| 13***02 | Nut | 1 |
| 24***06 | O Ring | 2 |
| 25***01 | Nut | 1 |
E3-3-1 Valve, Auxiliary, & Adapters
| 14***11 | Seal, Bonded | 1 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 5 |
| 16***04 | Adapter, Male/Male | 4 |
E3-2-4 Valve, Spool, Mechanical Detent, Loader Valve
| 24***05 | O Ring | 1 |
| 24***20 | O Ring | 2 |
| 24***07 | O Ring | 1 |
E3-4-1 Components, Auxiliary Valve
| 13***02 | Nut | 1 |
| 24***06 | O Ring | 2 |
| 24***16 | O Ring | 1 |
E3-5-3 Valve, Assembly, Excavator, Centremount, Sideshift
| 12***00 | Restrictor | 3 |
| 13***34 | Bolt | 1 |
| 13***36 | Bolt | 1 |
E3-2-6 Valve, Relief, Loader Valve
| 13***02 | Nut | 1 |
| 24***06 | O Ring | 1 |
| 24***07 | O Ring | 1 |
E3-2-5 Valve, Spool, Electric Detent, Loader Valve
| 24***07 | O Ring | 2 |
| 25***09 | O Ring | 2 |
| 25***18 | Spacer | 2 |
E3-2-3 Valve, Spool, Standard, Loader Valve
| 24***07 | O Ring | 2 |
| 25***09 | O Ring | 2 |
| 25***18 | Spacer | 2 |
E4-1-1 Ram, Lift, Basic Loader Arm
| 12***15 | Bush | 1 |
| 12***18 | Bush | 1 |
| 14***01 | Washer, Aluminium | 1 |
E4-3-5 Ram, Stabiliser, Centremount
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 14***11 | Seal, Bonded | 4 |
E4-6-3 Valve, Ram Lockout, Check
| 13***30 | Bolt | 2 |
| 13***03 | Nut | 2 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 6 |
E4-2-4 Ram, Backhoe, With Check Valve
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-6-2 Check Valve, Components
| 14***15 | Washer, Seal; Replaces Khj0891 | 1 |
| 14***16 | Seal, Bonded | 2 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 2 |
E4-7-1 Ram, Assembly, Service Exchange
E4-3-4 Ram, Stabiliser, Sideshift
| 55***01 | Cap, End | 1 |
| 55***02 | Head, Piston | 1 |
| 55***00 | Ram, Stabiliser, Sideshift; Standard. X= Early Type See E4-3-1. Y= Later Type See List Below., Ram, Stabiliser, Sideshift | 1 |
E4-2-7 Ram, Backhoe
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-2-6 Ram, Backhoe
| 12***15 | Bush | 1 |
| 12***20 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-4-2 Ram, Clamshovel, 6 In 1
| 12***11 | Bush | 1 |
| 12***19 | Bush | 1 |
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 2 |
E4-5-1 Seal Kits, Backhoe Rams
| 24***01 | O Ring | 1 |
| 24***15 | O Ring | 1 |
| 24***18 | O Ring | 1 |
E4-2-8 Ram, Backhoe, With Check Valve
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-5-2 Seal Kits, Extension Ram, Jaw Bucket
| 21***13 | Pin, Cotter, Split | 1 |
| 21***16 | Pin, Split | 1 |
| 24***26 | O Ring, 4.00in | 1 |
E4-1-2 Ram, Lift, Selflevel Loader Arm
| 12***15 | Bush | 1 |
| 12***18 | Bush | 1 |
| 14***01 | Washer, Aluminium | 1 |
E4-3-2 Ram, Stabiliser, Centremount
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 2 |
E4-2-2 Ram, Backhoe
| 12***15 | Bush | 2 |
| 12***21 | Bush | 2 |
| 12***17 | Bush | 2 |
E4-3-3 Ram Assy., Stabiliser With Chec, K Valve - Sideshift
| 55***01 | Head, Piston | 1 |
| 55***00 | Rod, Piston | 1 |
| 55***01 | Cap, End | 1 |
E4-3-7 Ram, Stabiliser, Centremount
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***29 | Bracket | 2 |
E4-2-1 Ram, Backhoe
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-6-4 Valve, Check
| 13***06 | Bolt | 2 |
| 14***11 | Seal, Bonded | 4 |
| 14***04 | Washer | 2 |
E4-8-1 Ram, Side Tip Shovel
| 98***01 | Ram | 1 |
| 98***03 | Pin, Rod End | 1 |
| 98***09 | Rod, Piston | 1 |
E4-6-1 Check Valve, Components
| 14***15 | Washer, Seal; Replaces Khj0891 | 1 |
| 24***09 | O Ring | 1 |
| 24***13 | O Ring | 2 |
E4-2-5 Ram, Backhoe
| 12***15 | Bush | 1 |
| 12***21 | Bush | 2 |
| 14***01 | Washer, Aluminium | 1 |
E4-4-3 Ram, Clamshovel, 6 In 1
| 12***11 | Bush | 1 |
| 12***19 | Bush | 1 |
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 2 |
E4-3-1 Ram, Stabiliser, Sideshift
| 55***01 | Head, Piston | 1 |
| 55***00 | Rod, Piston | 1 |
| 55***01 | Cap, End | 1 |
E4-2-3 Ram, Backhoe, With Check Valve
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-3-6 Ram, Stabiliser, Sideshift, With Check Valve
| 14***11 | Seal, Bonded | 4 |
| 16***02 | Adapter | 2 |
| 16***02 | Adapter, 1/4" Bsp M/M | 2 |
E4-4-1 Ram, Attachment
| 12***15 | Bush | 1 |
| 12***18 | Bush | 1 |
| 12***22 | Bush | 1 |
E4-1-4 Ram, Lift, Selflevel Loader Arm
| 12***15 | Bush | 1 |
| 14***01 | Washer, Aluminium | 1 |
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 1 |
E4-2-9 Ram, Backhoe, With Check Valve
| 12***15 | Bush | 1 |
| 12***21 | Bush | 1 |
| 12***17 | Bush | 2 |
E4-1-3 Ram, Lift, Basic Loader Arm
| 12***15 | Bush | 1 |
| 12***18 | Bush | 1 |
| 14***01 | Washer, Aluminium | 1 |
F Axles, Wheels & Transmission
F1-2-1 Gear Change
| 05***16 | Rod | 1 |
| 05***17 | Spring | 1 |
| 05***18 | Ball | 2 |
F1-4-1 Mountings, 498 Engine, Transmission
| 11***09 | Washer | 6 |
| 11***01 | Mounting, Metalastik | 1 |
| 12***00 | Mounting | 1 |
F1-4-2 Mountings, 4.236 Engine, Transmission
| 11***09 | Washer | 6 |
| 11***01 | Mounting, Metalastik | 4 |
| 12***00 | Mounting | 1 |
F1-3-1 Gearbox Components
| 05***55 | Shim, 0.003in | 0 |
| 05***06 | Seal, Oil | 1 |
| 05***08 | Seal, Oil | 2 |
F1-1-1 Gearbox Housing
| 05***01 | Gasket | 1 |
| 05***02 | Cover; N.L.A. Recommend Customer Go'S To Used Parts, Dealer. B Borsley'S Requested This. | 1 |
| 05***03 | Bolt | 6 |
F2-3-1 Clutch, Reverse, & Drive Pump
| 04***01 | Seal | 2 |
| 04***02 | Bearing | 1 |
| 04***03 | Carrier, Assembly | 1 |
F2-5-2 Flywheel & Housing, 4.236 Engine
| 02***76 | Washer, Tab | 3 |
| 02***77 | Flywheel, Assembly | 1 |
| 02***78 | Gear, Starter Ring | 1 |
F2-6-1 Circuit, Oil Cooler, Torque Converter
| 04***90 | Pipe; Use 04/50***04. | 1 |
| 04***91 | Elbow | 1 |
| 04***92 | Pipe | 1 |
F2-7-1 Propshaft, Transmission Drive
| 13***12 | Bolt | 8 |
| 13***03 | Nut | 8 |
| 14***03 | Nipple, Grease | 1 |
F2-2-1 Forward Clutch
| 04***01 | Seal | 2 |
| 04***20 | Gear, Drive | 1 |
| 04***21 | Gear, Hub | 1 |
F2-5-1 Flywheel & Housing, 498 Engine
| 02***18 | Plate | 1 |
| 02***19 | Bolt | 6 |
| 02***20 | Ring, Starter | 1 |
F2-1-1 Transmission, Shuttle Reverser
| 04***47 | Housing; Use Baffle 04/50***01 + 81***53 With The Abo, Ve., Lowing Parts 81***78 + 04/50***01 Ti Gen046. W When Fitting New Housing Please Order The Fol, Housing; Use Baffle 04/50***01 + 81***53 With The Abo, Ve. | 1 |
| 04***48 | Sleeve | 1 |
| 04***49 | Ring, Spacer | 1 |
F2-8-1 Filter
| 02***09 | Seal | 1 |
| 32***00 | Filter | 1 |
| 98***38 | Element, Oil Filter | 1 |
F2-4-1 Valve, Shuttle
| 04***58 | Spring | 1 |
| 04***59 | Valve, Assembly, Forward/Reverse | 1 |
| 04***61 | Seal | 1 |
F3-1-1 Axle Assembly - Std., 18.295 : 1
| 10***01 | Nut | 16 |
| 13***52 | Bolt | 4 |
| 13***09 | Bolt | 28 |
F3-4-1 Wheels & Tyres
| 10***01 | Nut | 1 |
| 41***00 | Wheel, 18.4/15x26 | 1 |
| 41***00 | Wheel, 14x28 | 1 |
F3-3-1 Crown Wheel & Pinion, - Std.
| 13***05 | Bolt | 1 |
| 13***08 | Bolt | 12 |
| 45***03 | Trunnion | 1 |
F3-1-3 Axle Assembly, 15.587 : 1
| 10***01 | Nut | 16 |
| 13***52 | Bolt | 4 |
| 13***09 | Bolt | 28 |
F3-3-3 Crown Wheel & Pinion
| 13***05 | Bolt | 1 |
| 13***08 | Bolt | 12 |
| 45***03 | Trunnion | 1 |
F3-1-2 Axle Assembly, German, 24.494 : 1
| 10***01 | Nut | 16 |
| 13***52 | Bolt | 4 |
| 13***09 | Bolt | 28 |
F3-2-4 9802/8000 F3-2-4
| 13***05 | Bolt | 1 |
| 13***10 | Bolt | 1 |
| 14***06 | Washer | 1 |
F3-2-1 Differential, Assembly
| 13***05 | Bolt | 14 |
| 13***09 | Bolt | 16 |
| 13***10 | Bolt | 16 |
F3-3-4 9802/8000 F3-3-4
| 13***08 | Bolt | 1 |
| 45***03 | Trunnion | 1 |
| 45***07 | Pin, Lock | 1 |
F3-3-2 Crown Wheel & Pinion, - German
| 13***05 | Bolt | 1 |
| 13***08 | Bolt | 12 |
| 45***03 | Trunnion | 1 |
F3-2-3 Differential, Assembly
| 13***05 | Bolt | 14 |
| 13***09 | Bolt | 16 |
| 13***10 | Bolt | 16 |
F3-2-2 Differential, Assembly - German
| 13***05 | Bolt | 14 |
| 13***09 | Bolt | 16 |
| 13***10 | Bolt | 16 |
F4-4-1 Propshafts, Axle Drive 4wd
| 12***01 | Strap | 1 |
| 12***02 | Plate | 1 |
| 12***03 | Clip, Steady | 1 |
F4-3-1 Crown Wheel & Pinion, 4wd
| 13***05 | Bolt | 1 |
| 13***08 | Bolt | 12 |
| 45***03 | Trunnion | 1 |
F4-2-2 Differential, Housing Assembly, 4wd - German
| 13***05 | Bolt | 14 |
| 13***09 | Bolt | 16 |
| 13***10 | Bolt | 16 |
F4-2-1 Differential, Housing Assembly, 4wd
| 13***05 | Bolt | 14 |
| 13***09 | Bolt | 16 |
| 13***10 | Bolt | 16 |
F4-1-1 Axle Assembly, 4wd
| 10***01 | Nut | 16 |
| 13***09 | Bolt | 28 |
| 13***52 | Bolt | 4 |
F4-5-1 Wheels & Tyres, 4wd
| 10***14 | Nut | 1 |
| 10***15 | Washer | 1 |
| 10***01 | Nut | 26 |
F4-1-2 Axle Assembly, 4wd, German
| 10***01 | Nut | 16 |
| 13***09 | Bolt | 28 |
| 13***52 | Bolt | 4 |
F4-3-2 Crown Wheel & Pinion, 4wd - German
| 13***05 | Bolt | 1 |
| 13***08 | Bolt | 12 |
| 45***03 | Trunnion | 1 |
G Brakes
G1-1-1 Brake System
| 12***00 | Pipe, Rh | 1 |
| 12***00 | Pipe, Lh | 1 |
| 12***00 | Pipe, Rh | 1 |
G1-2-1 Brake Assembly
| 13***09 | Bolt | 16 |
| 13***07 | Capscrew | 12 |
| 45***01 | Plate, Back | 2 |
G1-3-1 Brake, Parking
| 13***10 | Bolt | 4 |
| 14***08 | Washer, Spring | 4 |
| 15***01 | Pivot, Seat; Replaced By Nla, See San 11411 | 1 |
H Steering
H1-6-1 Valve, Shock, Steering, Optional
| 13***10 | Screw, Cap | 2 |
| 35***00 | Valve, Complete | 1 |
| 35***02 | Valve, Assembly, Shock | 1 |
H1-3-2 Steering Column
| 11***03 | Clip | 4 |
| 12***08 | Spacer | 2 |
| 12***01 | Wheel, Steering; Re J Smith Is Only Available From Manufacture, In Qty Of 500 Use 11***22, 11***08 | 1 |
H1-7-2 Ram, Steering
| 13***10 | Bolt | 2 |
| 13***16 | Bolt | 1 |
| 14***15 | Washer, Seal; Replaces Khj0891 | 2 |
H1-4-1 Pump, Steering, 4.98nt Engine
| 03***02 | Pump, Steering | 1 |
| 13***30 | Bolt, Long | 4 |
| 14***06 | Washer | 4 |
H1-3-1 Steering Column
| 11***03 | Clip | 4 |
| 12***03 | Mounting | 1 |
| 12***06 | Washer, Grooved | 1 |
H1-4-2 Pump, Steering, 4.236 Engine
| 12***02 | Gear | 1 |
| 13***12 | Bolt | 1 |
| 13***18 | Bolt | 2 |
H1-1-1 Axle Assembly Front, And Steering 2-Wd
| 12***01 | Pin, King | 2 |
| 12***02 | Pin, Cotter | 2 |
| 12***03 | Axle, Stub | 2 |
H1-2-2 Circuit, Steering
| 14***11 | Seal, Bonded | 1 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 1 |
| 16***04 | Adapter, Male/Female | 1 |
H1-2-1 Circuit, Steering
| 14***11 | Seal, Bonded | 1 |
| 61***00 | Hose; See Note 1. Kit Is Supplied With Connection Hoses 61***00, Hose; See Note 1. Kit Is Supplied With Hoses 61***00, Hose | 2 |
| 61***00 | Hose | 1 |
H1-7-1 Ram, Steering
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 2 |
| 22***56 | Circlip | 1 |
| 24***15 | O Ring | 1 |
H1-5-1 Valve, Steering
| 14***18 | Seal, Bonded, 1/2" Bsp | 4 |
| 16***07 | Adapter | 2 |
| 16***10 | Adapter | 2 |
H2-3-1 Hub & Components
| 10***14 | Nut | 12 |
| 10***15 | Washer | 12 |
| 10***17 | Nipple | 4 |
H2-2-1 Knuckle, Steering, 4wd Axle
| 10***02 | Pin, King | 4 |
| 10***05 | Seal | 4 |
| 10***06 | Shim, 0.1 | 4 |
H2-8-2 Knuckle, Steering, 4wd Axle
| 12***01 | Pin, Lock | 2 |
| 13***05 | Bolt | 2 |
| 13***08 | Bolt | 16 |
H2-8-3 Hub & Components
| 10***01 | Nut | 10 |
| 13***07 | Bolt | 32 |
| 13***08 | Bolt | 12 |
H2-8-1 Axle Assembly
| 12***01 | Pin, Lock | 2 |
| 13***28 | Bolt | 1 |
| 13***05 | Bolt | 2 |
H2-6-1 Ram, Steering, 4wd, Front
| 14***01 | Nipple, Grease, Straight, 1/8 Bsp | 2 |
| 22***56 | Circlip | 1 |
| 24***15 | O Ring | 1 |
H2-6-2 Ram, Steering, 4wd, Jcb Axle
| 14***01 | Washer, Aluminium | 2 |
| 14***01 | Nipple, Grease, 90deg. Angle | 2 |
| 24***06 | O Ring | 1 |
H2-4-1 Differential, Housing Assembly
| 10***01 | Housing | 1 |
| 10***02 | Bracket | 1 |
| 10***03 | Flange | 1 |
H2-5-1 Differential, Assembly, 4wd Axle
| 10***00 | Differential, Assembly | 1 |
| 10***01 | Housing | 1 |
| 10***02 | Flange | 1 |
H2-7-2 Circuit, Steering, 4wd
| 14***11 | Seal, Bonded | 1 |
| 14***18 | Seal, Bonded, 1/2" Bsp | 1 |
| 16***04 | Adapter, Male/Female | 1 |
H2-7-1 Circuit, Steering, 4wd
| 14***11 | Seal, Bonded | 1 |
| 61***00 | Hose | 2 |
| 61***00 | Hose | 1 |
H2-8-4 Differential, Assembly, 4wd Axle
| 10***00 | Differential, Assembly | 1 |
| 10***01 | Housing | 1 |
| 10***02 | Stud | 4 |
H2-1-1 Axle Assembly Front, 4wd And Steering
| 10***00 | Axle, Assembly, Steering | 1 |
| 10***01 | Casing | 1 |
| 10***03 | Pin, Pivot | 2 |
K Engine, Blmc 4.98nt
K1-5-1 Timing Gears
| 01***01 | Pulley, And Adapter | 1 |
| 02***01 | Block, Assembly, Cylinder | 1 |
| 02***02 | Belt, Drive | 1 |
K1-3-1 Crankshaft, Bearings, Pistons, Con-Rods, & Cylinder Liners
| 02***01 | Liner, Cylinder | 4 |
| 02***02 | Shim, 0.004in.(0.102mm) | 0 |
| 02***03 | Shim, 0.005in.(0.127mm) | 0 |
K1-7-1 Mountings, 4.98 Engine, Transmission
| 11***09 | Washer | 6 |
| 11***01 | Mounting, Metalastik | 1 |
| 12***00 | Mounting | 1 |
K1-1-1 Engine Basic
| 01***00 | Engine, Complete, 4.98nt Nat/Aspirated | 1 |
| 01***00 | Engine, Complete, 4.98tt Turbocharged | 1 |
| 01***00 | Engine, Complete, 4.98nt Nat/Aspirated | 1 |
K1-2-1 Block Assembly
| 02***94 | Tap, Drain | 1 |
| 02***00 | Block, Cylinder | 1 |
| 02***01 | Dowel, Hollow | 2 |
K1-4-1 Timing Case
| 02***08 | Casing, Timing | 1 |
| 02***09 | Cover, Timing | 1 |
| 02***10 | Plate, Lifting, Front | 1 |
K1-8-1 Flywheel & Housing, 4.98 Engine
| 02***18 | Plate | 1 |
| 02***19 | Bolt | 6 |
| 02***20 | Ring, Starter | 1 |
K1-1-0 Engine Build, Identification
K1-6-1 Gears, Oil Pump Drive
| 02***10 | Washer | 1 |
| 02***11 | Spindle | 1 |
| 02***12 | Collar | 1 |
K2-1-0 Engine Build, Identification
K2-4-1 Gasket Sets
| 81***04 | Gasket, Decarbonising | 1 |
| 81***05 | Kit-Gasket, Supplementary | 1 |
| 81***52 | Kit-Gasket, Decarbonising | 1 |
K2-3-1 Covers, Rocker & Tappet
| 02***42 | Cover | 1 |
| 02***44 | Pipe, Vent | 1 |
| 02***45 | Cover, Tappet | 1 |
K2-1-1 Cylinder Head
| 01***03 | Plate, Rear | 1 |
| 02***15 | Valve, Inlet | 4 |
| 02***16 | Valve, Exhaust | 4 |
K2-2-1 Rocker Assembly, Push Rods & Tappets
| 02***29 | Shaft, Rocker | 2 |
| 02***30 | Lever, Rocker | 8 |
| 02***31 | Spacer, 1/2in.(6.35mm) | 8 |
K2-1-2 Cylinder Head
| 01***03 | Plate, Rear | 1 |
| 02***16 | Valve, Exhaust | 4 |
| 02***20 | Holder, Collet | 8 |
K3-1-1 Manifold, Induction, Nat/Aspirated
| 02***46 | Adapter | 1 |
| 02***47 | Manifold | 1 |
| 12***01 | Plate, Adaptor | 1 |
K3-2-1 Filter, Air, Nat/Aspirated
| 12***05 | Bracket | 1 |
| 13***06 | Bolt | 2 |
| 13***04 | Bolt | 4 |
K3-3-1 Manifold, Exhaust, & Silencer, Nat/Aspirated
| 02***50 | Manifold | 1 |
| 02***51 | Nut | 2 |
| 12***00 | Silencer | 1 |
K3-1-0 Engine Build, Identification
K3-2-2 Filter, Air, Turbo
| 12***00 | Tube | 1 |
| 12***00 | Bracket | 1 |
| 12***00 | Tube | 1 |
K3-3-2 Manifold, Exhaust, & Silencer, Turbo
| 02***04 | Turbocharger | 1 |
| 02***05 | Manifold | 1 |
| 02***25 | Bolt | 4 |
K3-1-2 Manifold, Induction, Turbo
| 02***47 | Manifold | 1 |
| 02***02 | Pipe, Air Induction, Adapter | 1 |
| 02***03 | Hose, Air Induction | 1 |
K4-3-2 Radiator, Hoses & Fittings, Turbo
| 02***02 | Belt, Drive | 1 |
| 02***43 | Hose, By-Pass, L Shaped | 1 |
| 02***43 | Hose | 1 |
K4-2-1 Radiator, Fittings & Mountings, Nat/Aspirated
| 11***03 | Bracket, Top | 1 |
| 11***04 | Guard, Right Hand | 1 |
| 11***05 | Guard, Left Hand | 1 |
K4-3-1 Radiator, Hoses & Fittings, Nat/Aspirated
| 02***02 | Belt, Drive | 1 |
| 02***43 | Hose, By-Pass, L Shaped | 1 |
| 12***02 | Tube | 1 |
K4-1-1 Pump, Water
| 02***52 | Pulley | 1 |
| 02***53 | Spacer, Distance Piece | 1 |
| 02***54 | Body | 1 |
K4-2-2 Radiator, Fittings & Mountings, Turbo
| 11***03 | Bracket, Top | 1 |
| 11***04 | Guard, Right Hand | 1 |
| 11***05 | Guard, Left Hand | 1 |
K4-1-0 Engine Build, Identification
K4-1-2 Pump, Water
| 02***52 | Pulley | 1 |
| 02***54 | Body | 1 |
| 02***45 | Pulley | 1 |
K4-4-1 Thermostat, Housing, Inlet & Outlet
| 02***55 | Connector, Outlet | 1 |
| 02***56 | Thermostat, 82 Degree C | 1 |
| 02***57 | Thermostat, 74 Degree C | 1 |
K4-4-2 Thermostat, Housing, Inlet & Outlet
| 02***56 | Thermostat, 82 Degree C | 1 |
| 02***57 | Thermostat, 74 Degree C | 1 |
| 02***58 | Housing, Thermostat | 1 |
K5-1-0 Engine Build, Identification
K5-3-1 Filter, Oil
| 02***01 | Bolt | 1 |
| 02***02 | Collar | 1 |
| 02***03 | Seal | 1 |
K5-2-1 Pump, Oil
| 02***62 | Shim, .002in (0.51mm) | 0 |
| 02***63 | Shim, .003in.(.076mm) | 0 |
| 02***64 | Pipe, Suction | 1 |
K5-2-2 Pump, Oil
| 02***62 | Shim, .002in (0.51mm) | 0 |
| 02***63 | Shim, .003in.(.076mm) | 0 |
| 02***64 | Pipe, Suction | 1 |
K5-1-1 Sump, Oil
| 02***59 | Sump | 1 |
| 02***60 | Dipstick | 1 |
| 02***61 | Tube, Guide | 1 |
K5-4-1 Oil Feed Pipework
| 02***67 | Pipe, Overflow | 1 |
| 02***68 | Pipe | 1 |
| 02***04 | Pipe | 1 |
K5-5-1 Cooler, Oil Filter, Turbocharger Pipework
| 02***42 | Element, Oil Filter | 1 |
| 02***06 | Pipe, Turbo Oil Feed | 1 |
| 02***07 | Hose, Turbo Oil Feed | 1 |
K6-1-1 Fuel System
| 02***73 | Clamp | 2 |
| 02***74 | Pipe, Nylon | 1 |
| 02***75 | Clip | 1 |
K6-5-2 Filter, Fuel, Short
| 20***06 | Seal | 2 |
| 20***07 | Bolt, Centre | 1 |
| 20***08 | Washer | 1 |
K6-4-1 Pump, Fuel Lift
| 12***00 | Rod, Pull | 1 |
| 13***03 | Screw, 1/4 Unf X .625 | 1 |
| 13***06 | Bolt | 1 |
K6-5-1 Filter, Fuel, Long
| 13***16 | Bolt | 2 |
| 13***01 | Nut | 2 |
| 14***03 | Washer | 2 |
K6-4-2 Pump, Fuel Lift
| 17***00 | Pump, Fuel Lift | 1 |
| 17***11 | Kit-Repair | 1 |
| 17***12 | Kit-Seal | 1 |
K6-6-1 Filter, Fuel Sediment
| 13***03 | Nut | 2 |
| 20***00 | Filter, Assembly, Fuel Sediment | 1 |
| 20***01 | Head, Sediment Filter | 1 |
K6-2-1 Pump, Fuel Injection, Installation
| 02***77 | Bracket, Support | 1 |
| 02***78 | Plug | 1 |
| 02***79 | Hub | 1 |
K6-3-1 Injectors, Fuel
| 13***09 | Bolt | 2 |
| 14***05 | Washer; Replaces 82***03 | 2 |
| 17***05 | Nut | 1 |
K6-1-0 Engine Build, Identification
L Engine, 4.236
L1-1-3 Block Assembly, Imperial, Lj Build
| 02***01 | Thimble | 10 |
| 02***02 | Bolt | 10 |
| 02***03 | Liner, Press Fit; With Flame Ring. Special Tools For Fitting, Boring And Honing Required, General Service Use Slip Fit Type., Liner, Press Fit; With Flame Ring. Special Tools For Fitting, Boring And Honing Required, General Service Use Slip-Fit Type., Liner, Press Fit; Flame Ring Type. Special Tools Required, For General Service, Use Slip-Fit Type., Liner, Press Fit, Liner, Press Fit; Flame Ring Type. Special Tools Required, For General Service, Use Slip Fit Type., Liner, Press Fit; Flame Ring Type. This Requires Specialised Tools For Fitting, For General Service Use Slip-Fit Type., Liner, Press Fit; Flame Ring Type. Special Tools For Fitting, Boring And Honing Required, General Service Use Slip Fit Type., Liner, Press Fit; Refer To Service Workshop Manual. Special Tools Required For Fitting, Boring And Honing,For General Service Use Slip-Fit., Liner, Press Fit; Refer To Service Workshop Manual. Special Tools Required For Fitting, Boring And Honing, General Service Use Slip-Fit Type., Liner, Press Fit; Refer To Workshop Manual. Special Tools Required For Fitting, Boring And Honing, General Service Use Slip-Fit Type., Liner, Press Fit; Flame Ringed Type. This Requires Specialised Tools For Fitting, For General Service, Use Slip-Fit Type., Liner, Press Fit; Flame Ringed Type. Special Tools For Fitting, Boring And Honing Required, General Service Use Slip-Fit Type. | 4 |
L1-8-1 Short Engine
| 02***25 | Engine, Short, Imperial | 1 |
L1-8-3 Engine, Short, Imperial, Lh & Lj Builds
| 02***09 | Engine, Short, Imperial | 1 |
L1-4-1 Flywheel & Housing, Ld,Lh & Lj Builds
| 02***76 | Washer, Tab | 3 |
| 02***77 | Flywheel, Assembly | 1 |
| 02***78 | Gear, Starter Ring | 1 |
L1-7-1 Engine, Complete, Ld Build
| 01***00 | Engine, Imperial, Complete, 4.236 Nat/Aspirated | 1 |
| 01***0R | Engine, Imperial, 4.236 Nat/Aspirated, Engine, Imperial, 4.236 Nat/Aspirated; See Note 2. Fuel Filter & Pipework, Fan Belt, Thermostat,Outlet Connection & Inlet, Exhaust Manifolds. | 1 |
| 01***00 | Engine, Imperial, Complete, 4.236 Nat/Aspirated | 1 |
L1-2-1 Crankshaft, Bearings, Pistons, Con-Rods, Pulley & Fan Belt, Ld & Lh Builds
| 02***07 | Piston, Assembly, 5 Ring | 4 |
| 02***08 | Piston, Assembly, Oversize - .030inch | 4 |
| 02***09 | Kit-Piston Ring | 4 |
L1-7-3 Engine, Complete, Lj Build
| 01***00 | Engine, Imperial, Complete, 4.236 Turbocharged | 1 |
| 01***0R | Engine, Imperial, 4.236 Turbocharged | 1 |
| 01***00 | Engine, Imperial, Complete, 4.236 Turbocharged; Lj50183 Superseded By N.S.P. Part No Longer Available Use 01/11***00 And Refer To T.I.K135/H, K129/E., Engine, Imperial, Complete, 4.236 Turbocharged; Lj50183 S/Seded By N.S.P. Part No Longer Available Use 02/11***00 And Refer To T.I.K135/H - K129/E., Engine, Imperial, Complete, 4.236 Turbocharged, Engine, Imperial, Complete, 4.236 Turbocharged; Lj50183 Supersede By N.S.P. Part No Longer Available, Use 01/11***00 And Refer To T.I.K135/H K129/E. | 1 |
L1-3-2 Timing Case, Camshaft & Gears, Lj Build
| 02***02 | Casing, Timing | 1 |
| 02***05 | Gasket, Timing Case | 1 |
| 02***06 | Gasket, Timing Cover | 1 |
L1-3-1 Timing Case, Camshaft & Gears, Ld & Lh Builds
| 02***02 | Casing, Timing | 1 |
| 02***03 | Cover, Timing | 0 |
| 02***04 | Seal, Front Oil | 0 |
L1-1-1 Block Assembly, Imperial, Ld & Lh Builds
| 02***16 | Bolt, 89mm | 6 |
| 02***17 | Bolt, 105mm | 12 |
| 02***01 | Thimble | 10 |
L1-6-1 Engine Mountings, Ld,Lh & Lj Builds
| 11***09 | Washer | 6 |
| 11***01 | Mounting, Metalastik | 4 |
| 12***00 | Mounting | 1 |
L1-2-3 Crankshaft, Bearings, Pistons, Con-Rods, Pulley & Fan Belt, Lj Build
| 02***38 | Key | 1 |
| 02***27 | Bolt | 1 |
| 02***28 | Nut | 1 |
L1-7-2 Engine, Complete, Lh Build
| 01***00 | Engine, Imperial, Complete, 4.236 Compensated | 1 |
| 01***0R | Engine, Imperial, 4.236 Compensated | 1 |
| 01***0R | Engine, Imperial, 4.236 Compensated; & 1, Lh50205. Fuel Filter & Pipework,Fan Belt,Outlet Connection & Inlet/Exhaust Manifolds., Engine, Imperial, 4.236 Compensated | 1 |
L2-2-1 Rocker Cover, Ld Build
| 02***35 | Cover, Rocker | 1 |
| 02***36 | Gasket, Rocker Cover | 1 |
| 02***80 | Pipe | 1 |
L2-4-1 Turbo, Heatshield, Lh & Lj Builds
| 02***15 | Guard, Heat | 1 |
| 02***00 | Guard, Heat | 1 |
| 02***80 | Shield, Heat | 1 |
L2-1-1 Cylinder Head, Ld Build
| 02***14 | Head, Assembly, Cylinder | 1 |
| 02***15 | Nut | 2 |
| 02***18 | Spring, Valve, Inner | 8 |
L2-3-2 Rocker Assembly, Push Rods & Tappets, Ld, Lh & Lj Builds
| 02***27 | Shaft, Rocker | 1 |
| 02***28 | Spring, Long | 2 |
| 02***29 | Spring, Short | 2 |
L2-2-2 Rocker Cover, Lh & Lj Builds
| 02***37 | Cap, Oil Filler | 1 |
| 02***80 | Pipe | 1 |
| 02***22 | Seal | 1 |
L2-1-4 Cylinder Head, Lj Build
| 02***18 | Spring, Valve, Inner | 8 |
| 02***19 | Spring, Valve, Outer | 8 |
| 02***21 | Holder, Collet | 8 |
L2-1-2 Cylinder Head, Lj Build
| 02***18 | Spring, Valve, Inner | 8 |
| 02***19 | Spring, Valve, Outer | 8 |
| 02***20 | Seat, Spring | 8 |
L2-1-3 Cylinder Head, Ld & Lh Builds
| 02***24 | Collet | 8 |
| 02***26 | O Ring; Exhaust. Used Only With Cylinder Heads 02/10***82 And 02/10***24., O Ring, O Ring; Inlet & Exhaust. No Longer Required | 4 |
| 02***48 | Plug | 1 |
L2-3-1 Rocker Assembly, Push Rods & Tappets, Ld Build
| 02***27 | Shaft, Rocker | 1 |
| 02***28 | Spring, Long | 2 |
| 02***29 | Spring, Short | 2 |
L3-5-6 Silencer & Extension, Lh & Lj Builds
| 02***52 | Gasket | 1 |
| 12***00 | Pipe, Exhaust Extension | 1 |
| 12***00 | Pipe, Exhaust | 1 |
L3-4-1 Filter, Air, Ld Build
| 12***00 | Bracket, Air Filter Mounting | 1 |
| 12***02 | Bracket | 1 |
| 12***03 | Pad, Mounting | 4 |
L3-2-1 Manifold, Exhaust, Ld Build
| 02***49 | Manifold, Exhaust | 1 |
| 02***50 | Gasket | 2 |
| 02***51 | Nut | 4 |
L3-1-2 Manifold, Induction, Lh & Lj Builds
| 02***16 | Manifold, Induction | 1 |
| 02***07 | Gasket | 1 |
| 02***08 | Gasket | 1 |
L3-4-8 Filter, Air, Ld Build
| 12***02 | Bracket | 1 |
| 13***04 | Bolt | 2 |
| 13***10 | Bolt | 1 |
L3-4-6 Filter, Air, Lh & Lj Builds
| 12***00 | Bracket | 1 |
| 12***00 | Hose, Assembly, Induction | 1 |
| 12***01 | Hose, Induction Elbow | 1 |
L3-2-2 Manifold, Exhaust, Lh & Lj Builds
| 02***50 | Gasket | 1 |
| 02***51 | Nut | 4 |
| 02***17 | Manifold, Exhaust | 1 |
L3-1-1 Manifold, Induction, Ld Build
| 02***45 | Manifold, Induction | 1 |
| 02***46 | Gasket | 1 |
| 02***47 | Gasket | 1 |
L3-5-1 Silencer & Extension, Ld Build
| 02***52 | Gasket | 1 |
| 12***00 | Pipe, Exhaust Extension | 1 |
| 12***00 | Pipe, Exhaust Extension | 2 |
L4-4-7 Radiator, Hoses & Fittings, Ld Build
| 12***00 | Bracket | 1 |
| 12***00 | Bottle, Expansion, Assembly | 1 |
| 12***03 | Hose, Overflow Assembly | 1 |
L4-3-3 Thermostat, Housing, Inlet & Outlet, Lh & Lj Builds
| 02***95 | Plug, Taper | 2 |
| 02***99 | Gasket | 1 |
| 02***59 | Connector, Water Outlet | 1 |
L4-3-1 Thermostat, Housing, Inlet & Outlet, Ld Build
| 02***71 | Thermostat | 1 |
| 02***98 | Housing, Thermostat | 1 |
| 02***99 | Gasket | 1 |
L4-4-1 Radiator & Hoses
| 12***02 | Tube | 1 |
| 12***00 | Bottle, Expansion | 1 |
| 12***02 | Cap, Filler | 1 |
L4-1-3 Pump, Water, Lh & Lj Builds
| 02***67 | Gasket | 1 |
| 02***94 | Body, Rear | 1 |
| 02***95 | Plug, Taper | 1 |
L4-1-4 Pump, Water, Lh & Lj Builds
| 02***67 | Gasket | 1 |
| 02***94 | Body, Rear | 1 |
| 02***95 | Plug, Taper | 1 |
L4-1-1 Pump, Water, Ld Build
| 02***66 | Pump, Water | 1 |
| 02***67 | Gasket | 1 |
| 02***70 | Kit-Repair, Water Pump; Contains Items 3,4,5,6.7.8.9.10,1.11.12.13.27. Items 7,9.10,1 & 11 No Longer Required,Repaired And Replaced By Kit 02/10***87., Kit-Repair, Water Pump; Contains Items 3.4.5.6.7.8.9.10,1.11.12.13.27. Items 7.9.10,1 & 11 No Longer Required,Repaired And Replaced By Kit 02/10***87., Kit-Repair, Water Pump, Kit-Repair, Water Pump; Contains Items 3.4.5.6.7.8.9.10,1.11.12.13.27. Items 7.9.10,1. & 11 No Longer Required,Repaired And Replaced By Kit 02/10***87., Kit-Repair, Water Pump; Contains Items 3.4.5.6.7.8.9.10,1.11.12.13.27. Items 7.9.10,1 & 11 No Longer Required,Repaired And Replaced By Kit., Kit-Repair, Water Pump; Contains Items 3,4,5,6,7,8,9,10,11,12,13 & 27. Items 7,8,9 & 11, Repaired And Replaced By K It 02/10***87., Kit-Repair, Water Pump; Contains Items 3,4,5,6.7.8.9.10,1.11.12.13.27. Items 7.9.10,1 & 11 Are No Longer Required, Repaired And Replaced By Kit 02/10***87. | 1 |
L4-4-6 Radiator, Hoses & Fittings, Lh & Lj Builds
| 12***00 | Bracket | 1 |
| 12***00 | Bottle, Expansion, Assembly | 1 |
| 12***03 | Hose, Overflow Assembly | 1 |
L5-1-1 Sump, Oil Pump, & Fittings, Ld,Lh & Lj Builds
| 02***59 | Sump, Oil | 1 |
| 02***60 | Gasket, Oil Sump | 1 |
| 02***61 | Pump, Oil | 1 |
L5-2-3 Filter, Oil & Cooler, Lh & Lj Builds
| 02***63 | Gasket | 1 |
| 02***71 | Head, Filter | 1 |
| 02***84 | Element, Oil Filter, Canister Type-Short | 1 |
L5-2-1 Filter, Oil, Ld Build
| 02***63 | Gasket | 1 |
| 02***73 | Element, Oil Filter, Canister Type - Long | 1 |
| 02***71 | Head, Filter | 1 |
L5-2-4 Filter, Oil & Cooler, Lh & Lj Builds
| 02***63 | Gasket | 0 |
| 02***71 | Head, Filter | 0 |
| 02***84 | Element, Oil Filter, Canister Type-Short | 0 |
L6-3-2 Controls, Throttle & Stop, Swedish Builds
| 02***83 | Spring, Stop/Return | 1 |
| 02***84 | Spring, Throttle Return | 1 |
| 10***01 | Connector | 1 |
L6-1-2 Pump, Fuel Injection, Ld & Lh Builds
| 17***00 | Pump, Fuel Injection | 1 |
| 17***00 | Pump, Fuel Injection | 1 |
| 17***02 | Screw | 1 |
L6-2-1 Bracket, Throttle & Stop
| 02***83 | Spring, Stop/Return | 1 |
| 02***84 | Spring, Throttle Return | 1 |
| 02***90 | Bracket | 2 |
L6-9-1 Fuel System, Ld & Lh Builds
| 02***82 | Pipe, Assembly, Fuel, L/Pump To Filter | 1 |
| 02***83 | Pipe, Fuel, Assembly, Filter To Inj/Pump | 1 |
| 02***84 | Pipe, Fuel, Assembly, Inj/Pump To Filter | 1 |
L6-4-2 Pump, Fuel Lift, Alternative
| 17***12 | Kit-Seal | 1 |
| 17***00 | Pump, Fuel Lift | 1 |
| 17***19 | Kit-Repair, Fuel Lift Pump | 1 |
L6-3-1 Controls, Throttle & Stop
| 02***83 | Spring, Stop/Return | 1 |
| 02***84 | Spring, Throttle Return | 1 |
| 12***00 | Pedal, Throtle Control | 1 |
L6-9-6 Fuel System, Lj Build
| 02***82 | Pipe, Assembly, Fuel, L/Pump To Filter | 1 |
| 02***83 | Pipe, Fuel, Assembly, Filter To Inj/Pump | 1 |
| 02***84 | Pipe, Fuel, Assembly, Inj/Pump To Filter | 1 |
L6-6-1 Filter, Fuel Sediment, Ld,Lh & Lj Builds
| 20***00 | Filter, Assembly, Fuel Sediment | 1 |
| 20***01 | Head, Sediment Filter | 1 |
| 20***03 | Element, Assembly | 1 |
L6-1-4 Pump, Fuel Injection, Lj Build
| 17***00 | Pump, Fuel Injection; 0r 3241f881 If Totally Stuck Use 3348f212 To, Modify And Recalibrate To Make 3241f790 | 1 |
| 17***02 | Screw | 1 |
| 17***03 | Nut | 3 |
L6-7-1 Filter, Fuel, Ld,Lh & Lj Builds
| 02***89 | Bracket | 1 |
| 02***94 | Banjo | 1 |
| 02***95 | Valve, Non-Return | 1 |
L6-1-3 Fuel Injection, Equipment, Lj Build
| 02***53 | Washer | 4 |
| 02***81 | Washer | 8 |
| 02***90 | Bolt | 3 |
L6-4-1 Pump, Fuel Lift, Ld,Lh & Lj Builds
| 02***80 | Gasket | 1 |
| 02***72 | Plate, Keep | 2 |
| 02***98 | Screw | 1 |
L6-1-1 Fuel Injection, Equipment, Ld & Lh Builds
| 02***53 | Washer | 4 |
| 02***54 | Pipe, No.1 Cylinder | 1 |
| 02***55 | Pipe, No.2 Cylinder | 1 |
L8-3-2 Turbo, Pipework, Lh & Lj Builds
| 02***51 | Nut | 4 |
| 02***87 | Olive | 1 |
| 02***10 | Washer | 4 |
L8-2-2 Turbocharger, Lh & Lj Builds
| 02***56 | Turbocharger | 1 |
| 02***57 | Housing, Assembly, Centre | 1 |
| 02***58 | Nut, Lock | 1 |
L8-3-3 Turbo, Pipework, Lh & Lj Builds
| 02***51 | Nut | 4 |
| 02***58 | Union | 1 |
| 02***87 | Olive | 1 |
L9-1-2 Gasket Sets, Turbo Engine
| 02***97 | Kit-Gasket, Top | 1 |
| 02***98 | Kit-Gasket, Bottom | 1 |
| 02***89 | Kit-Gasket, Top; Lh50133,Lh50205 & Lj50183. Refer To Service Workshop Manual, Kit-Gasket, Top | 1 |
L9-2-3 Kit, Engine Overhaul, Lj Build
| 02***06 | Liner, Slip Fit | 4 |
| 02***35 | Seal, Front Oil | 1 |
| 02***36 | Seal, Rear Oil | 1 |
L9-2-1 Kit, Engine Overhaul, Ld Build
| 02***07 | Piston, Assembly, 5 Ring | 4 |
| 02***06 | Liner, Slip Fit | 4 |
| 02***35 | Seal, Front Oil | 1 |
L9-1-1 Gaskets Sets
| 02***66 | Kit-Gasket, Bottom | 1 |
| 02***87 | Kit-Gasket, Top | 1 |
| 02***88 | Kit-Gasket, Bottom | 1 |
L9-2-2 Kit, Engine Overhaul, Lh Build
| 02***06 | Liner, Slip Fit | 4 |
| 02***20 | Kit-Piston Ring | 4 |
| 02***35 | Seal, Front Oil | 1 |
3CX-2 serial number reference
On JCB 3CX and 4CX backhoe loaders, the machine identification plate is located on the right-hand side of the loader tower or cab frame. Major components such as the engine, axles, and gearbox carry their own serial plates; the loader-tower PIN alone is insufficient for parts identification. For machines without a visible plate, check stamped numbers on the cab side near the rear wheel or confirm applicability with a JCB dealer.
| Prefix | Identifies | Notes |
|---|---|---|
| 00930000-00959999 | JCB 3CX-2 Sitemastr Backhoe Loader; Parts Catalogue Manual applicability | . Source text contains typos ('BACKOHE') but explicitly links the range to the 3CX-2 model. |
Frequently asked questions
What engine does the JCB 3CX-2 use?
The JCB 3CX-2 uses a JCB DieselMax 4-cylinder turbocharged diesel engine or a JCB EcoMAX variant, delivering 74.6 kW (100 hp) and 440 Nm of torque at 1,600 rpm. It meets Tier 4 Final standards without DEF or DPF.
What is the operating weight of the JCB 3CX-2?
The operating weight varies by configuration, ranging from approximately 6,616 kg (14,586 lb) for lighter setups to 8,300 kg (18,300 lb) for heavier 4WD configurations with standard attachments.
What model replaced the JCB 3CX-2?
The JCB 3CX Plus replaced the 3CX-2 generation, introduced around 2021. It features updated emissions compliance and modernized cab ergonomics while retaining the compact backhoe loader platform.
What 3CX-2 owners discuss
What are the common powertrain and hydraulic behaviors reported for the JCB 3CX-2 regarding forward movement and torque converter performance?
Operators report that early 3CX models (circa 1980s) may exhibit 'lazy' movement or lack of power in forward gear while retaining full power in reverse. This is often attributed to the torque converter stall ratio or slipping shuttle drive packs. Electrical failures in the forward/reverse microswitches or solenoids are also frequent causes of forward drive loss. For 2013+ models, low drive power can stem from a faulty electric transfer/supply pump or deadman switch issues. Hydraulic leaks are common, particularly from the extend-a-hoe boom cylinders and valve block seals, causing the boom to drop under its own weight.
What undercarriage, axle, and wear patterns are typical for the JCB 3CX series?
Wear patterns vary by generation. Older models (pre-1990s) often feature 8-bolt axles, while later models use 5-bolt axles with reduction hubs. The slew gearbox is a separate system from the main hydraulics and requires its own 90-weight gear oil; water accumulation in the slew kingpin area is a known issue requiring periodic draining. Front axle hubs and the rear slew gearbox are distinct service points. The machine is prone to hydraulic leaks at the pump shaft and cylinder seals.
What engine quirks and fuel system issues are associated with the JCB 3CX-2 and related 3CX generations?
Early 3CX models (1980s) used non-turbo Perkins engines (e.g., LD series 4.236L/236 ci) and shared fuel systems with the older 3C3. A common issue is fuel strainer blockage in the lift pump due to 'fuel bug' or grunge in the tank, which is often a welded section of the frame. Later models (2015+) use the JCB Ecomax T4f engine. The 2020+ 3CX uses the JCB DieselMax 4-cylinder turbocharged engine (74.6 kW/100 hp). White sludge in filters indicates water contamination or silicate separation in the coolant system.
What are the common electrical and sensor issues for the JCB 3CX-2?
The forward/reverse shuttle lever operates microswitches that activate hydraulic solenoids on the transmission body. Failure of the forward microswitch or solenoid causes loss of forward drive. The inhibitor switch (neutral start switch) prevents starting in gear; if bridged or faulty, it can cause starting issues. Newer models (2016+) may exhibit flashing warning lights or error codes related to DEF systems or electronic controls that require dealer-level clearing.
What specific fluids and lubricants are recommended for the JCB 3CX-2 and its variants?
Engine oil: JCB 15W/40 Multigrade or equivalent diesel-rated oil (e.g., SUTO 15/40 for older non-turbo models). Hydraulic fluid: JCB HP46 or ISO 46 hydraulic fluid. Transmission and wet brakes: JCB Super Universal Agricultural oil or multipurpose oil suitable for wet brake systems. Axle hubs and front axles: 90-weight gear oil (e.g., JCB HD90 Gear Oil). Slew gearbox: 90-weight gear oil in a separate sump. Coolant: Must be changed at recommended intervals to prevent silicate separation and brown sludge formation.
What is the recommended 'what to check when buying a used 3CX-2' entry?
Verify the exact serial number and engine type (Perkins LD vs. JCB DieselMax/Ecomax) to ensure correct manual and parts compatibility. Check the forward/reverse microswitches and solenoids for electrical continuity. Inspect the torque converter filter for metal filings indicating internal wear. Test the extend-a-hoe boom for drift (dropping under weight), which indicates inner/outer seal or valve block failure. Check for water in the slew gearbox kingpin drain. Verify the fuel lift pump strainer is clean and the tank is free of 'fuel bug' grunge. Confirm the condition of the turbo exhaust housing for cracks.
What safety-critical fixes require dealer verification?
Clearing persistent error codes on newer electronic models (2016+) and verifying DEF system functionality. Any repair involving the high-pressure common rail fuel injection system (up to 2000 bar/29,010 psi) or turbocharger replacement. Verification of brake system integrity, particularly the master cylinder fluid level and wet brake operation.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Serial-range & configuration variants
This page covers the Jcb 3CX-2. Related factory variants of the same model family:
3CX-2
Need a specific 3CX-2 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.