Caterpillarwork toolshear-demolition/scrap
Caterpillar VHS-70
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar VHS-70 is a passive, excavator-mounted hydraulic demolition and scrap shear built by Verachtert and sold under the Cat badge. It carries no engine, ECM, or fuel system of its own; the carrier excavator's auxiliary hydraulic circuit supplies all jaw-closing force. Caterpillar tracks it across at least three factory configurations: a base H/M generation from 1997 to 2000, a /3 generation built through the 2000s, and a /4 generation from roughly 2010 to 2012 built alongside the VHS-60/4 sibling on a shared serial-prefix range. Operating weight runs from about 8 t (17,600 lb) on the base generation to roughly 8.6 t (18,960 lb) on the /3 generation; /4-generation weight is not published in available factory literature. It is part of Caterpillar's wider VHS-10/30/40/50/60/70 shear family and mounts either pin-on to a stick or boom, or through a quick-coupler bracket, matched to a carrier class that runs roughly 65 to 95 tonnes depending on generation and mounting method.
Later generations tightened the jaw opening from 1000 mm on the base H/M generation down to 880 mm on the /3 generation despite a heavier structure, pointing to reinforced castings rather than a bigger bite. Documented cutting force on the base generation runs 11,760 kN, and carrier class crept up toward the 85-95 t stick-mount range as the tool grew heavier through the generations. No source ties the VHS-70 to a confirmed factory successor the way the VHS-60/4 carried forward into Cat's own S365C badge; treat any current S-series equivalent as a size-class comparison, not a documented replacement. That gap doesn't hurt resale: because the tool is purely mechanical/hydraulic, a used VHS-70 of any generation still runs on wear parts - blades, pivot pins, bushings, cylinder seals - sourced through the same Cat/Verachtert parts network as current shears, which keeps scrap yards and demolition contractors buying older units for the lower cost per cut against a new tool.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar VHS-70 specifications
Engine
| Power source | Passive excavator-mounted hydraulic shear — no onboard engine, ECU, or fuel system. Runs entirely off the carrier excavator's auxiliary hydraulic circuit. |
| Emissions tier | Not applicable — tool has no engine. |
Weights
| Operating weight (base H/M generation) | 8 t (17,637 lb) |
| Operating weight (/3 generation) | 8.6 t (18,960 lb) |
| Operating weight (/4 generation) | Not published in available spec sheets — confirm with dealer for the exact configuration |
| Shipping weight | Not published separately from operating weight in available sources |
| Ground pressure | Not applicable — excavator-mounted attachment, no ground contact of its own |
Dimensions
| Total length (base H/M generation) | 5700 mm (224.4 in) |
| Jaw opening (base H/M generation) | 1000 mm (39.4 in) |
| Jaw opening (/3 generation) | 880 mm (34.6 in) — narrower than the base generation despite the heavier /3 operating weight; verify against the exact serial range before quoting |
| Cylinder bore x stroke (/4 generation) | 360 mm x 866 mm (14.2 in x 34.1 in) — shared cylinder spec with the VHS-60/4 sibling tool |
| Transport width/height | Not published in available spec sheets for this model |
Performance
| Cutting force (base H/M generation) | 11,760 kN |
| Cutting force (/3 and /4 generations) | Not published in available sources |
| Travel speed / gradeability | Not applicable — passive excavator-mounted shear, no self-propulsion |
| Host carrier weight class (base H/M generation) | Approx. 65-90 t (72-99 US tons); figures vary by mounting type (direct stick mount vs quick-change coupler) per dealer literature — confirm the exact carrier match with your dealer |
| Host carrier weight class (/3 generation) | Approx. 85-95 t (94-105 US tons) |
Service capacities (summary)
| Hydraulic system | No onboard reservoir. Draws hydraulic power from the carrier excavator's auxiliary circuit — match fluid type and service intervals to the carrier's own hydraulic oil specification |
| Fuel tank | Not applicable — tool has no engine |
| Engine oil | Not applicable — tool has no engine |
| Cooling system | Not applicable — tool has no engine |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
VHS-70 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | Not applicable — the VHS-70 is a passive hydraulic demolition/scrap shear work tool with no onboard engine. | Not applicable. |
| Cooling system | Not applicable — no engine, so no coolant circuit fitted to this attachment. | Not applicable. |
| Fuel tank | Not applicable — the shear carries no fuel system. | Not applicable. |
| Transmission / powertrain compartment | Not applicable — no drivetrain; jaw motion comes entirely from the carrier excavator's hydraulic cylinders. | Not applicable. |
| Final drives (each) | Not applicable — no final drives on this work tool. | Not applicable. |
| Axles/differentials | Not applicable — no axles on this work tool. | Not applicable. |
| Hydraulic system and tank | No dedicated reservoir capacity published for this attachment. The shear has no hydraulic tank of its own; cylinder bore and stroke for the VHS-70/4 configuration are documented at roughly 360 mm (14.2 in) bore by 866 mm (34.1 in) stroke, but that is a cylinder dimension, not a fill volume. | Runs directly off the carrier excavator's auxiliary hydraulic circuit. Fluid type, viscosity grade, and any cold/hot-climate split follow the host machine's own operation and maintenance manual (typically an anti-wear hydraulic oil such as Cat HYDO Advanced graded to ambient temperature), not a VHS-70-specific specification. |
| Grease points (blade pivot pin, jaw linkage, mounting-ear bushings) | No fill quantity specified; serviced by grease gun at each nipple until fresh grease purges from the joint, on a routine interval rather than a fixed volume. | General-purpose extreme-pressure chassis grease, NLGI grade 2, with moly (molybdenum disulfide) additive for pin and bushing joints — consistent with Cat's Advanced 3Moly Grease or Extreme Application Grease product lines used across the Cat work-tool range. Shorten intervals in wet, muddy, or high-debris demolition environments; cooler climates call for a lighter-bodied grease of the same type. No single named product is confirmed as the factory call-out specifically for the VHS-70 line in sources checked — treat as a standard moly EP grease pending direct OMM confirmation. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar VHS-70 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
Servicing the VHS-70 beyond the schedule
Predictive Maintenance & Fluid Analysis
The VHS-70 has no engine to sample, so predictive work runs through the carrier's shared hydraulic circuit. Pull oil samples from the carrier to catch metal particulate shed by cylinder seal or pivot pin wear before it shows up as leakage. Track jaw pivot and mounting-ear bushing clearance across intervals to see wear trending toward the replacement limit. Match carrier auxiliary-circuit flow to the shear's rated requirement, since undersized flow shows up first as slow jaw closing, not a fault code.
Corrective & Common Repairs
Recurring failures on the VHS-70 trace to cyclic jaw-closing loads: pivot pins at the jaw hinge and mounting ears wear first, showing up as knocking or play under a test cut. Blade and piercing-tip edges chip or round off fastest cutting rebar-laden concrete; reversible, indexable blades buy extra service life before a full change. Main cylinder rod seals weep once debris packs the wiper, and a drifting jaw under load signals seal failure, not a simple leak. Hose chafing at the pivot area is another common wear point.
Overhaul & Rebuild Points
Major overhaul on the VHS-70 centers on the jaw structure and main cylinder. Line-bore worn pivot and mounting-ear bores back to tolerance and fit matched pin-and-bushing sets rather than mixing old with new. Pull the main cylinder for a full reseal, honing the barrel if the rod shows scoring. Replace or index all reversible cutting edges together so jaw geometry stays true. Re-torque or replace mounting-bracket and coupler hardware, and run crack testing on jaw castings before the shear returns to service.
Seasonal & Environment Servicing
The VHS-70 carries no coolant or fuel system to winterize, but open pivot lube washes out fast on wet demolition sites, so shorten grease intervals in rain or standing water and switch to a low-temperature grease below freezing. Gritty, rebar-laden concrete debris accelerates blade wear in yard environments, so check edges more often. Flush concrete dust and rebar fines from pivot points after wet work, and protect exposed cylinder rods from corrosion during long outdoor storage.
VHS-70 attachments & work tools
Shear jaw / work tool type
VHS-70 is itself a fixed hydraulic scrap and demolition shear head (Verachtert-built, Cat-badged), not a carrier that takes swap-on tools. No separate pulverizer or grapple jaw is documented for this size in the VHS line; the shear jaw is the fixed work tool.
Cutting capacity class
For the VHS-70/3 generation: girder/H-beam sections up to roughly 600-650mm height and 300mm width, solid round bar to about 130mm diameter, solid square to about 120mm, plate to about 16mm, and pipe to about 500mm diameter x 15mm wall. Closing (jaw) force is on the order of 1,300 ton; figures vary by generation and series.
Carrier / mounting bracket
Two mounting approaches are used: a fixed mounting-bracket group for direct stick or boom mounting, or a CW-70 class pin-grabber quick coupler. Carrier tonnage guidance runs roughly 50-65t for boom mount up to 85-95t for stick mount on the /3 generation, while the CW-70 coupler itself is rated for carriers in the 65-90t range - actual carrier fit varies by mounting configuration and generation.
Hydraulic kit / arrangement
Operation requires a dedicated auxiliary hydraulic shear arrangement plumbed from the carrier's high-flow auxiliary circuit. Jaw open/close typically needs high flow at up to roughly 350 bar. Carriers not already fitted for demolition-shear duty need this auxiliary hydraulic kit added.
Factory generations / configuration
VHS-70 exists in at least two documented factory generations (/3 and /4), each with its own mounting-bracket parts group and serial-prefix scheme; the /3 generation's mounting-bracket documentation is shared with the VHS-30/3 through VHS-60/3 siblings, but carrier-class rating and hydraulic arrangement are specific to the VHS-70 size within that shared manual.
All VHS-70 assemblies by section
Every catalogued assembly group for the Caterpillar VHS-70. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Frame And Body
242-3736 Cover Gp-Access
| 17***10 | Rotator Group-Hydraulic | 1 |
| 19***87 | Housing Group-Shear | 1 |
| 21***50 | Housing Group-Shear | 1 |
242-9603 Cover Gp-Access
| 17***96 | Housing Group-Shear | 1 |
| 17***98 | Rotator Group-Hydraulic | 1 |
| 24***03 | Cover Group-Access | 1 |
242-9605 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***05 | Cover Group-Access | 1 |
242-2062 Cover Gp-Access
| 16***60 | Rotator Group-Hydraulic | 1 |
| 17***55 | Housing Group-Shear | 1 |
| 21***97 | Housing Group-Shear | 1 |
247-8415 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***15 | Cover Group-Access | 1 |
242-2063 Cover Gp-Access
| 16***60 | Rotator Group-Hydraulic | 1 |
| 18***99 | Housing Group-Shear | 1 |
| 21***96 | Housing Group-Shear | 1 |
243-1539 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***39 | Cover Group-Access | 1 |
243-1540 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 1 |
| 24***40 | Cover Group-Access | 1 |
242-9604 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 1 |
| 24***04 | Cover Group-Access | 1 |
247-8418 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***18 | Cover Group-Access | 1 |
247-8416 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***16 | Cover Group-Access | 1 |
247-8417 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***17 | Cover Group-Access | 1 |
227-4318 Guide Gp-Lines
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 22***18 | Guide Group-Lines | 1 |
| 24***58 | Latch Group-Access Door | 1 |
235-0577 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
196-2019 Housing Gp-Shear
| 08***10 | Setscrew; (M10x21-mm) | 6 |
| 10***88 | Bolt-Socket Head; (M10x1.5x16-mm) | 3 |
| 15***18 | Lockwasher | 6 |
217-1397 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 10 |
| 15***21 | Lockwasher | 18 |
177-3355 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 17***55 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 2 |
216-6850 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 15***46 | Seal | 1 |
217-1395 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 46 |
| 15***21 | Lockwasher | 18 |
245-8017 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
195-0777 Housing Gp-Shear
| 19***77 | Housing Group-Shear | 1 |
| 22***15 | Plate As | 1 |
| 6V***89 | Locknut; (M8x1.25-Thd) | 1 |
184-3399 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 18***99 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 1 |
217-1396 Housing Gp-Shear
| 14***78 | Lockwasher | 24 |
| 15***21 | Lockwasher | 24 |
| 16***64 | Bolt-Socket Head; (M20x2.5x55-mm) | 24 |
318-9778 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 10 |
| 15***21 | Lockwasher | 18 |
318-9773 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 14***78 | Lockwasher | 24 |
| 15***19 | Lockwasher | 2 |
197-7187 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 15***46 | Seal | 1 |
| 15***18 | Lockwasher | 8 |
245-8016 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
318-9776 Housing Gp-Shear
| 14***78 | Lockwasher | 24 |
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 24 |
217-1398 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 11***73 | Seal; (0.5cm) (X2) | 0 |
171-5496 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 17***96 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 2 |
242-2058 Latch Gp-Access Door
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 34 |
| 16***12 | Clip; (Slot) | 2 |
171-5558 Mounting Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 18 |
Hydraulic System
171-5554 Cylinder & Lines Gp-Shear
| 09***69 | Bolt | 24 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
177-3369 Cylinder & Lines Gp-Shear
| 10***86 | Spring | 1 |
| 17***69 | Cylinder & Lines Group-Shear | 1 |
| 24***59 | Latch | 1 |
196-2026 Cylinder & Lines Gp-Shear
| 12***11 | Hose As | 1 |
| 16***54 | Seal | 1 |
| 16***16 | Seal | 1 |
171-5497 Cylinder & Lines Gp-Shear
| 09***69 | Bolt | 24 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
222-8828 Cylinder & Lines Gp-Shear
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 8 |
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
187-2996 Cylinder & Lines Gp-Shear
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
| 17***60 | Cylinder Group-Shear | 1 |
187-2962 Cylinder & Lines Gp-Shear
| 17***35 | Mounting Group-Cylinder | 1 |
| 17***49 | Lines Group-Cylinder | 1 |
| 17***54 | Cylinder & Lines Group-Shear | 1 |
184-3404 Cylinder & Lines Gp-Shear
| 18***04 | Cylinder & Lines Group-Shear | 1 |
| 28***28 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
222-8830 Cylinder & Lines Gp-Shear
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
| 18***78 | Cylinder Group-Shear | 1 |
184-3403 Cylinder & Valve Gp
| 12***11 | Hose As | 1 |
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
187-2945 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
177-3360 Cylinder & Valve Gp
| 12***22 | Bolt; (M14x2x50-mm) | 8 |
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
187-2993 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
196-2022 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
171-5560 Cylinder Gp-Shear
| 14***06 | Bolt-Socket Head; (M20x2.5x140-mm) | 5 |
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
196-2030 Cylinder Gp-Shear
| 16***16 | Seal | 1 |
| 16***03 | Bushing | 2 |
| 17***23 | Plug As | 2 |
187-2978 Cylinder Gp-Shear
| 16***16 | Seal | 1 |
| 16***03 | Bushing | 2 |
| 17***23 | Plug As | 2 |
184-3405 Cylinder Gp-Shear
| 14***06 | Bolt-Socket Head; (M20x2.5x140-mm) | 5 |
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
177-3368 Cylinder Gp-Shear
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***19 | Lockwasher | 2 |
197-6880 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***41 | Bushing | 2 |
292-1512 Lines Gp-Connecting
| 19***69 | Hose As | 2 |
| 1P***05 | Seal (Check Valve Outlet) | 4 |
| 29***12 | Lines Group-Connecting | 1 |
225-2729 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 17***23 | Plug As | 4 |
241-5636 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***87 | Bushing | 2 |
242-1185 Lines Gp-Connecting
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 2 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 14***18 | Reducer; (-8orfs/-12orfs Swivel) | 2 |
201-7607 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 14***84 | Bolt-Socket Head; (M20x2.5x110-mm) | 22 |
| 16***16 | Seal | 1 |
177-5026 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 09***06 | Bolt-Socket Head; (M16x2x80-mm) | 24 |
| 16***16 | Seal | 1 |
242-1184 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 09***06 | Bolt-Socket Head; (M16x2x80-mm) | 24 |
| 16***16 | Seal | 1 |
318-4547 Lines Gp-Connecting
| 16***46 | Bar-Clamp | 2 |
| 16***90 | Clip; (Slot) | 2 |
| 16***91 | Clip; (Tab) | 2 |
291-1280 Lines Gp-Connecting
| 12***40 | Fitting As-Hydraulic; (Quick Disconnect, Male) | 2 |
| 17***33 | Hose As | 2 |
| 29***80 | Lines Group-Connecting | 1 |
171-5565 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***87 | Bushing | 2 |
171-5549 Lines Gp-Cylinder
| 17***49 | Lines Group-Cylinder | 1 |
| 24***84 | Lines Group-Connecting | 1 |
| 24***85 | Lines Group-Connecting | 1 |
170-2174 Manifold Gp-Control
| 17***74 | Manifold Group-Control | 1 |
| 24***38 | Hose As | 2 |
| 6V***98 | Seal-O-Ring -Line From Gear Pump Output | 2 |
170-2172 Motor & Manifold Gp-Rotator
| 16***43 | Seal | 1 |
| 17***72 | Motor & Manifold Group-Rotator | 1 |
| 17***05 | Adapter As | 2 |
216-7650 Motor Gp-Gerotor
| 1P***04 | Seal - Rectangular (45mm Dia) | 1 |
| 1P***67 | Flange-Half (43.31 mm Id) | 2 |
| 21***50 | Motor Group-Gerotor | 1 |
320-1326 Motor Gp-Gerotor
| 29***43 | Hose As | 2 |
| 29***45 | Hose As | 2 |
| 32***26 | Motor Group-Gerotor | 1 |
170-2173 Motor Gp-Gerotor
| 10***36 | Connector | 2 |
| 10***37 | Seal | 1 |
| 15***94 | Adapter As | 2 |
171-5535 Mounting Gp-Cylinder
| 17***35 | Mounting Group-Cylinder | 1 |
| 32***36 | Hose As | 2 |
| 32***37 | Hose As | 2 |
171-5555 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***74 | Manifold Group-Control | 1 |
| 17***76 | Ring-Mounting | 1 |
194-6068 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***74 | Manifold Group-Control | 1 |
| 17***77 | Gear-Drive; (15-Teeth) | 1 |
319-2123 Rotator Gp-Hydraulic
| 09***07 | Nut; (M12x1.75-Thd) | 4 |
| 14***53 | Plug | 1 |
| 18***82 | Bolt-Socket Head; (M20x2.5x65-mm) | 16 |
216-7649 Rotator Gp-Hydraulic
| 03***43 | Seal-O-Ring | 1 |
| 08***09 | Spacer; (16.6x32x8.5-mm Thk) | 34 |
| 12***28 | Adaptor - Includes:- | 2 |
171-7526 Rotator Gp-Hydraulic
| 17***21 | Kit-Housing | 1 |
| 17***22 | Shaft-Output | 1 |
| 17***25 | Key-Square | 1 |
217-1423 Rotator Gp-Hydraulic
| 15***94 | Adapter As | 2 |
| 15***44 | Seal | 1 |
| 15***46 | Seal | 1 |
171-5498 Rotator Gp-Hydraulic
| 14***20 | Bolt-Socket Head; (M6x1x75-mm) | 4 |
| 17***98 | Rotator Group-Hydraulic | 1 |
| 7Y***19 | Seal-O-Ring (Id=12.37mm) | 2 |
171-8110 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***76 | Ring-Mounting | 1 |
| 17***77 | Gear-Drive; (15-Teeth) | 1 |
169-6060 Rotator Gp-Hydraulic
| 15***35 | Elbow As | 4 |
| 15***18 | Lockwasher | 2 |
| 15***19 | Lockwasher | 1 |
319-2124 Rotator Gp-Hydraulic
| 03***43 | Seal-O-Ring | 1 |
| 09***48 | Nipple, Grease | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
170-3045 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 16 |
| 12***28 | Adaptor - Includes:- | 4 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 4 |
265-6468 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 16 |
| 12***28 | Adaptor - Includes:- | 4 |
| 12***24 | Seal-O-Ring; (12.37mm Id) | 4 |
172-1124 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 8 |
| 12***28 | Adaptor - Includes:- | 4 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 4 |
174-4901 Valve Gp-Control -Quick
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 8 |
| 12***28 | Adaptor - Includes:- | 4 |
| 12***24 | Seal-O-Ring; (12.37mm Id) | 4 |
208-8451 Valve Gp-Control
| 08***72 | Seal-O-Ring | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 15***94 | Adapter As | 6 |
170-3229 Valve Gp-Speed Control
| 08***72 | Seal-O-Ring | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 15***94 | Adapter As | 6 |
208-5125 Valve Gp-Speed Control
| 16***43 | Seal | 1 |
| 17***57 | Plug As | 4 |
| 17***14 | Stator | 1 |
172-2207 Valve Gp-Speed Control
| 16***43 | Seal | 1 |
| 17***41 | Stator | 1 |
| 17***42 | Rotor | 1 |
Service Equipment And Supplies
197-3519 Film Gp
200-2135 Film Gp
200-8571 Film Gp
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
195-0776 Film Gp
| 16***80 | Kit-Service; (Counterbalance Valve) | 2 |
| 18***01 | Manifold | 1 |
| 18***02 | Valve | 1 |
197-3843 Film Gp
197-7184 Film Gp
184-3400 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 15***96 | Film-Notice; (Lift Eye Location) | 5 |
| 15***35 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
200-2134 Kit-Maintenance
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
177-3356 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
235-2732 Kit-Maintenance
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
197-7186 Kit-Maintenance
| 14***08 | Fitting | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
235-2730 Kit-Maintenance
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
183-5625 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
235-0605 Kit-Maintenance
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
195-0775 Kit-Maintenance
| 14***08 | Fitting | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
200-2961 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***92 | Wrench | 1 |
200-2960 Lock Gp-Shear
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
200-2962 Lock Gp-Shear
| 20***62 | Lock Group-Shear | 1 |
199-8486 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
200-2959 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
200-2885 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
Work Tool Arrangement
197-7182 Shear Ar-Hydraulic
| 19***82 | Shear Ar-Hydraulic | 1 |
| 19***84 | Film Group | 1 |
| 19***85 | Shear Group-Hydraulic | 1 |
200-8570 Shear Ar-Hydraulic
| 18***25 | Kit-Maintenance | 1 |
| 19***30 | Shear Group-Hydraulic | 1 |
| 20***70 | Shear Ar-Hydraulic | 1 |
197-3842 Shear Ar-Hydraulic
| 18***00 | Kit-Maintenance | 1 |
| 19***42 | Shear Ar-Hydraulic | 1 |
| 19***43 | Film Group | 1 |
200-2133 Shear Ar-Hydraulic
| 19***17 | Shear Group-Hydraulic | 1 |
| 20***33 | Shear Ar-Hydraulic | 1 |
| 20***34 | Kit-Maintenance | 1 |
197-3518 Shear Ar-Hydraulic
| 17***56 | Kit-Maintenance | 1 |
| 19***18 | Shear Ar-Hydraulic | 1 |
| 19***19 | Film Group | 1 |
195-0772 Shear Ar-Hydraulic
| 19***72 | Shear Ar-Hydraulic | 1 |
| 19***74 | Shear Group-Hydraulic | 1 |
| 19***75 | Kit-Maintenance | 1 |
Work Tools
200-7804 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***04 | Bracket Group-Mounting | 1 |
| 20***10 | Bracket Group-Mounting | 1 |
257-0098 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***98 | Bracket Group-Mounting | 1 |
169-5311 Bracket Gp-Mounting
| 16***11 | Bracket Group-Mounting | 1 |
| 16***16 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
200-7808 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 16***96 | Seal; (Id=99.85mm) | 2 |
179-1651 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 17***18 | Bracket As | 1 |
257-0099 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***99 | Bracket Group-Mounting | 1 |
| 25***02 | Bracket Group-Mounting | 1 |
202-0285 Bracket Gp-Mounting
| 17***61 | Cover | 2 |
| 20***84 | Bracket As | 1 |
| 20***85 | Bracket Group-Mounting | 1 |
257-1041 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***41 | Bracket Group-Mounting | 1 |
291-4097 Bracket Gp-Mounting
| 15***19 | Lockwasher | 8 |
| 29***97 | Bracket Group-Mounting | 1 |
| 29***22 | Bracket As | 1 |
200-7809 Bracket Gp-Mounting
| 14***90 | Bearing-Sleeve; (140.26mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
201-5016 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***14 | Bracket Group-Mounting | 1 |
| 20***16 | Bracket Group-Mounting | 1 |
253-7830 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 1 |
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
201-5014 Bracket Gp-Mounting
| 09***54 | Seal; (Id=79.85mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
201-5015 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***13 | Bracket Group-Mounting | 1 |
| 20***15 | Bracket Group-Mounting | 1 |
169-4971 Bracket Gp-Mounting
| 16***71 | Bracket Group-Mounting | 1 |
| 16***91 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
201-9466 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***97 | Plate-Cover | 1 |
| 20***66 | Bracket Group-Mounting | 1 |
179-1645 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***18 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
222-8507 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 22***07 | Bracket Group-Mounting | 1 |
| 22***13 | Bracket Group-Mounting | 1 |
283-4187 Bracket Gp-Mounting
| 15***97 | Seal-Lip Type | 2 |
| 19***46 | Insert | 1 |
| 26***24 | Bearing-Sleeve | 2 |
291-5775 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 29***75 | Bracket Group-Mounting | 1 |
180-1286 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 18***86 | Bracket Group-Mounting | 1 |
| 19***94 | Bracket Group-Mounting | 1 |
169-5312 Bracket Gp-Mounting
| 16***12 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***54 | Bracket Group-Mounting | 1 |
175-3012 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 17***12 | Bracket Group-Mounting | 1 |
| 17***53 | Bracket Group-Mounting | 1 |
257-0101 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***01 | Bracket Group-Mounting | 1 |
276-7982 Bracket Gp-Mounting
| 15***97 | Seal-Lip Type | 2 |
| 19***46 | Insert | 1 |
| 26***24 | Bearing-Sleeve | 2 |
283-4827 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 23***25 | Plate-Serial Number | 1 |
| 28***27 | Bracket Group-Mounting | 2 |
222-8508 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
275-8137 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 27***37 | Bracket Group-Mounting | 1 |
| 27***77 | Bracket As | 1 |
200-7506 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 16***97 | Plate-Cover | 1 |
169-4970 Bracket Gp-Mounting
| 16***70 | Bracket Group-Mounting | 1 |
| 16***90 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
299-0293 Bracket Gp-Mounting
| 17***09 | Edge-Cutting | 2 |
| 17***10 | Edge-Cutting | 2 |
| 17***11 | Cutter | 1 |
275-9776 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 27***76 | Bracket Group-Mounting | 1 |
| 27***83 | Bracket As | 1 |
169-4969 Bracket Gp-Mounting
| 16***69 | Bracket Group-Mounting | 1 |
| 16***89 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
200-7800 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***00 | Bracket Group-Mounting | 1 |
| 20***06 | Bracket Group-Mounting | 1 |
169-4967 Bracket Gp-Mounting
| 16***67 | Bracket Group-Mounting | 1 |
| 16***86 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
287-6820 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 28***20 | Bracket Group-Mounting | 1 |
| 29***75 | Bracket Group-Mounting | 1 |
199-0719 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 16 |
| 19***40 | Bracket Group-Mounting | 1 |
| 19***19 | Bracket Group-Mounting | 1 |
197-5352 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 48 |
| 19***52 | Bracket Group-Mounting | 1 |
| 19***53 | Bracket Group-Mounting | 1 |
200-7803 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 20***03 | Bracket Group-Mounting | 1 |
| 20***09 | Bracket Group-Mounting | 1 |
254-4039 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***71 | Washer; (26x90x8-mm Thk) | 1 |
169-4978 Bracket Gp-Mounting
| 16***78 | Bracket Group-Mounting | 1 |
| 16***97 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
169-4968 Bracket Gp-Mounting
| 16***68 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 23***05 | Bracket As | 1 |
169-5307 Bracket Gp-Mounting
| 16***07 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***47 | Bracket Group-Mounting | 1 |
199-7008 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***07 | Bracket Group-Mounting | 1 |
| 19***08 | Bracket Group-Mounting | 1 |
257-1047 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 25***47 | Bracket Group-Mounting | 1 |
| 27***38 | Bracket As | 1 |
175-0342 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***42 | Bracket Group-Mounting | 1 |
| 17***49 | Bracket As | 1 |
200-7805 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***05 | Bracket Group-Mounting | 1 |
| 20***11 | Bracket Group-Mounting | 1 |
246-9991 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 24***91 | Bracket Group-Mounting | 1 |
283-4186 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 28***86 | Bracket Group-Mounting | 2 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
200-7807 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 20***07 | Bracket Group-Mounting | 1 |
201-5013 Bracket Gp-Mounting
| 09***54 | Seal; (Id=79.85mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
198-7616 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***13 | Bracket As | 1 |
222-3345 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 16 |
| 22***45 | Bracket Group-Mounting | 1 |
| 22***11 | Bracket Group-Mounting | 1 |
169-4980 Bracket Gp-Mounting
| 16***80 | Bracket Group-Mounting | 1 |
| 16***98 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
291-1291 Bracket Gp-Mounting
| 15***19 | Lockwasher | 8 |
| 16***95 | Seal; (Id=93.00mm) | 2 |
| 22***89 | Bearing-Sleeve | 2 |
200-7801 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***01 | Bracket Group-Mounting | 1 |
| 20***07 | Bracket Group-Mounting | 1 |
222-8513 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 22***13 | Bracket Group-Mounting | 1 |
| 22***78 | Bracket Group-Mounting | 1 |
175-3014 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 17***14 | Bracket Group-Mounting | 1 |
| 17***51 | Bracket Group-Mounting | 1 |
199-1258 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
169-4976 Bracket Gp-Mounting
| 16***76 | Bracket Group-Mounting | 1 |
| 16***96 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
175-0338 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***38 | Bracket Group-Mounting | 1 |
| 17***46 | Bracket Group-Mounting | 1 |
248-7980 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 24***80 | Bracket Group-Mounting | 1 |
245-8009 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 20***59 | Plate-Serial Number | 1 |
249-3132 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 2 |
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
200-7802 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***02 | Bracket Group-Mounting | 1 |
| 20***08 | Bracket Group-Mounting | 1 |
179-1653 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 17***16 | Bracket As | 1 |
257-0102 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***02 | Bracket Group-Mounting | 1 |
| 25***47 | Bracket Group-Mounting | 1 |
169-4981 Bracket Gp-Mounting
| 16***81 | Bracket Group-Mounting | 1 |
| 16***99 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
205-3923 Bracket Gp-Mounting
| 20***23 | Bracket Group-Mounting | 1 |
| 20***46 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
205-3920 Bracket Gp-Mounting
| 20***20 | Bracket Group-Mounting | 1 |
| 20***70 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
217-0996 Bracket Gp-Mounting
| 15***19 | Lockwasher | 18 |
| 17***61 | Cover | 2 |
| 21***96 | Bracket Group-Mounting | 1 |
200-7810 Bracket Gp-Mounting
| 09***34 | Shim; (T=69.85mm) | 2 |
| 11***82 | Bearing-Sleeve | 2 |
| 15***19 | Lockwasher | 16 |
193-9094 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
| 19***94 | Bracket Group-Mounting | 1 |
222-8512 Bracket Gp-Mounting
| 14***90 | Bearing-Sleeve; (140.26mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
247-0536 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 15***21 | Lockwasher | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
179-1646 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***97 | Plate-Cover | 1 |
| 17***45 | Bracket As | 1 |
198-7615 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***15 | Bracket Group-Mounting | 1 |
| 19***16 | Bracket Group-Mounting | 1 |
199-1259 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 19***58 | Bracket Group-Mounting | 1 |
| 19***59 | Bracket Group-Mounting | 1 |
199-7007 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***06 | Bracket As | 1 |
222-8511 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 22***11 | Bracket Group-Mounting | 1 |
202-0286 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 48 |
| 20***85 | Bracket Group-Mounting | 1 |
| 20***86 | Bracket Group-Mounting | 1 |
224-2477 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 22***77 | Bracket Group-Mounting | 1 |
179-1654 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***15 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
197-7840 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***39 | Bracket As | 1 |
222-8506 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 22***06 | Bracket Group-Mounting | 1 |
| 22***12 | Bracket Group-Mounting | 1 |
336-0800 Bracket Gp-Mounting
| 14***87 | Screw-Flat Head | 2 |
| 14***75 | Bolt; (M20x2.5x75-Thd) | 6 |
| 16***85 | Edge-Cutting | 4 |
291-1266 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 29***66 | Bracket Group-Mounting | 1 |
| 29***97 | Bracket Group-Mounting | 1 |
224-2478 Bracket Gp-Mounting
| 22***78 | Bracket Group-Mounting | 1 |
| 24***32 | Bracket Group-Mounting | 1 |
193-4497 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***97 | Bracket Group-Mounting | 1 |
| 20***66 | Bracket Group-Mounting | 1 |
200-7811 Bracket Gp-Mounting
| 09***34 | Shim; (T=69.85mm) | 2 |
| 11***82 | Bearing-Sleeve | 2 |
| 15***19 | Lockwasher | 16 |
254-4463 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***71 | Washer; (26x90x8-mm Thk) | 2 |
| 25***63 | Bracket Group-Mounting | 1 |
169-5308 Bracket Gp-Mounting
| 16***08 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***45 | Bracket Group-Mounting | 1 |
200-7806 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 20***06 | Bracket Group-Mounting | 1 |
283-4828 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
175-0341 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***41 | Bracket Group-Mounting | 1 |
| 17***48 | Bracket As | 1 |
255-0001 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***01 | Bracket Group-Mounting | 1 |
| 25***99 | Bracket Group-Mounting | 1 |
169-4974 Bracket Gp-Mounting
| 16***74 | Bracket Group-Mounting | 1 |
| 16***93 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
197-5353 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
| 19***53 | Bracket Group-Mounting | 1 |
179-1647 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***19 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
171-5499 Edge Gp-Cutting
| 14***98 | Screw-Flat Head; (M20x2.5x90-mm) | 12 |
| 14***87 | Screw-Flat Head | 3 |
| 16***85 | Edge-Cutting | 1 |
217-1413 Edge Gp-Cutting
| 11***30 | Bolt-Socket Head; (M20x2.5x150-mm) | 4 |
| 14***78 | Lockwasher | 4 |
| 21***13 | Edge Group-Cutting | 1 |
195-0780 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 7 |
| 14***87 | Screw-Flat Head | 7 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
236-2204 Edge Gp-Cutting
| 20***86 | Plate-Lock | 2 |
| 23***04 | Edge Group-Cutting | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
196-2023 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 7 |
| 14***87 | Screw-Flat Head | 7 |
| 14***78 | Lockwasher | 3 |
234-1339 Edge Gp-Cutting
| 14***78 | Lockwasher | 3 |
| 17***93 | Bolt-Socket Head; (M20x2.5x80-mm) | 3 |
| 22***49 | Plate-Wear | 1 |
217-1410 Edge Gp-Cutting
| 14***87 | Screw-Flat Head | 2 |
| 14***75 | Bolt; (M20x2.5x75-Thd) | 6 |
| 15***21 | Lockwasher | 3 |
234-9152 Edge Gp-Cutting
| 19***00 | Bar | 1 |
| 23***52 | Edge Group-Cutting | 1 |
| 8T***89 | Locknut; (M10x1.15-Thd) | 2 |
217-1412 Edge Gp-Cutting
| 14***78 | Lockwasher | 3 |
| 17***80 | Bolt-Socket Head; (M20x2.5x120-mm) | 3 |
| 21***12 | Edge Group-Cutting | 1 |
184-7651 Edge Gp-Cutting
| 14***66 | Screw-Flat Head; (M24x3x160-mm) | 9 |
| 14***25 | Screw-Flat Head | 9 |
| 17***81 | Edge-Cutting | 1 |
216-7648 Edge Gp-Cutting
| 14***98 | Screw-Flat Head; (M20x2.5x90-mm) | 12 |
| 14***87 | Screw-Flat Head | 3 |
| 15***21 | Lockwasher | 3 |
197-7455 Edge Gp-Cutting
| 11***30 | Bolt-Socket Head; (M20x2.5x150-mm) | 4 |
| 14***66 | Screw-Flat Head; (M24x3x160-mm) | 9 |
| 14***25 | Screw-Flat Head | 9 |
177-3359 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 14 |
| 14***81 | Screw-Flat Head | 3 |
| 16***85 | Edge-Cutting | 1 |
197-7185 Shear Gp-Hydraulic
| 17***26 | Rotator Group-Hydraulic | 1 |
| 19***77 | Housing Group-Shear | 1 |
| 19***85 | Shear Group-Hydraulic | 1 |
199-8930 Shear Gp-Hydraulic
| 19***68 | Rotator Group-Hydraulic | 1 |
| 19***19 | Housing Group-Shear | 1 |
| 19***30 | Shear Group-Hydraulic | 1 |
196-2017 Shear Gp-Hydraulic
| 19***17 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
195-0774 Shear Gp-Hydraulic
| 19***74 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
197-3844 Shear Gp-Hydraulic
| 19***44 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
197-3520 Shear Gp-Hydraulic
| 19***20 | Shear Group-Hydraulic | 1 |
| 20***17 | Plate-Lock | 2 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
VHS-70 serial number reference
On this Cat/Verachtert shear the PIN plate is a riveted metal tag mounted on the shear body or top mounting bracket near the pivot housing, not on a carrier machine frame, since this is a work tool and not a self-propelled unit. The plate shows the full Product Identification Number; the first three characters are the prefix identifying model and generation, and the digits that follow are the sequential unit serial for that prefix.
| Prefix | Identifies | Notes |
|---|---|---|
| B1Y | VHS-70/3 (3rd-generation shear; prefix shared across the VHS-30/3, VHS-40/3, VHS-50/3, VHS-60/3 and VHS-70/3 line, all covered by the same factory parts manual) | Passive hydraulic shear jaw, no engine or ECM of its own. Mounts on an excavator stick or on a quick coupler. Carrier class runs roughly 60 to 90 t for stick mounting; quick-coupler mounting is quoted much wider in some sources, so treat carrier weight as varying by mounting method and source rather than one fixed figure. No plant or region breakout published for this prefix. Open serial range (00001-UP). |
| M1C | VHS-70/4 (4th-generation shear; prefix shared with the VHS-60/4 sibling under the same parts manual) | Passive attachment, no engine. The VHS-60/4 sharing this prefix corresponds to the Cat-badged S365C shear; no separate Cat S-number was confirmed tied specifically to VHS-70/4, so treat that equivalence as unconfirmed and check with a dealer if it matters. Carrier class figures found for this generation vary by source (a narrower stick-mount range versus a much wider quick-coupler range), so treat as varying by configuration. No plant/region info published. Open serial range (00001-UP). |
Frequently asked questions
What engine does the Caterpillar VHS-70 use?
None. The VHS-70 is a passive hydraulic shear with no engine, ECM, or crankcase of its own. It draws all cutting force from the carrier excavator's auxiliary hydraulic circuit; factory literature for the /3 generation documents an oil flow around 690 l/min for jaw opening and closing, so match the carrier's auxiliary output to the shear's rated flow rather than looking for an onboard powerplant.
What is the operating weight of the Caterpillar VHS-70?
It varies by generation. The base H/M generation (1997-2000) runs about 8 t (17,600 lb). The /3 generation, built through the 2000s, runs heavier at roughly 8.6 t (18,960 lb) despite a narrower jaw opening. Operating weight for the later /4 generation (around 2010-2012) is not published in available factory literature - confirm the exact figure against the serial prefix with your dealer before matching it to a carrier.
What replaced the Caterpillar VHS-70?
No confirmed factory successor is documented specifically for the VHS-70. Unlike its VHS-60/4 sibling, which carried forward directly into Cat's own S365C badge, no source ties the VHS-70 to a named replacement model. Caterpillar's current S3-series shears cover a similar size class today, but treat that as a market comparison, not a documented lineage - verify cross-reference with your Cat dealer if you need a direct like-for-like replacement.
What VHS-70 owners discuss
What generations of the VHS-70 are out there, and do they differ much?
Owners report at least three distinct builds under the VHS-70 name: an early M-configuration unit from the late 1990s, an H-configuration unit rated for roughly 65-90 t (143,000-198,000 lb) carriers, and a later /4-generation unit built alongside the VHS-60/4 sharing the same serial-prefix range. Operating weight varies from about 8 t up to 11.5 t (17,600-25,350 lb) depending which one you have, so treat any single spec sheet as configuration-specific, not universal. Confirm generation from the serial prefix stamped on the housing before ordering parts or comparing specs.
What hydraulic flow and pressure does the VHS-70 actually need from the carrier?
This is a passive attachment with no engine or onboard power source of its own — every bit of cutting force comes from the host excavator's auxiliary hydraulic circuit. Operators consistently say an undersized pump or restrictive plumbing shows up as slow jaw closing speed and weak cutting force long before anything breaks, not as a fault code. Matching flow and pressure to the carrier's rated auxiliary output, and to this shear's weight class, is the single biggest factor in getting rated cutting force. Have your dealer verify your specific carrier's auxiliary circuit output against the shear's requirement before buying or fitting.
How much wear should I expect on the jaw and cutting blades, and how is it serviced?
Community consensus on this class of shear is consistent: the cutting blades are the fastest-wearing item and are designed to be indexed — rotated to a fresh edge — well before they need outright replacement. Chipping, a rounded-over cutting edge, or a visible radius where a sharp corner used to be are the signs it's time to index or swap. The upper jaw casting itself can be built back up by a competent shop, but the blades cannot; they're a hardened alloy that doesn't take a weld repair well. Bolt-on wear tips and edges save the main structure from taking the abuse directly.
What's the pin and bushing wear pattern like on the shear's mounting ears and jaw pivot?
Same story owners report across the whole demolition-shear category: the mounting pins (stick/dipper ears) and the main jaw pivot pin see the most cyclic load and wear first, with bushings wearing a bit slower. Symptoms of neglect are a knocking or clunking under load, visible play when you rock the jaw by hand, and an egged-out bore if it's gone too long between greasings. A tight lubrication interval matters more here than on a bucket because the jaw pivot sees full hydraulic force on every cut, not just digging resistance. Excess pivot play is a safety item — have your dealer verify pin and bushing clearances before returning the tool to service.
Does the VHS-70 rotate 360 degrees on the carrier?
No — the VHS-70 is a fixed-jaw shear. It mounts pin-on to the stick, or through a quick-coupler bracket sized to the carrier class, but it does not have an independent continuous-rotation drive built into the tool itself. Continuous 360-degree rotation on this family of shears is a separate, dedicated rotating product line, not a VHS feature. If a used listing shows independent rotation, that's a different tool wearing a similar badge — confirm before assuming interchangeability.
What hydraulic cylinder or hose issues come up with age on this shear?
The two complaints that come up repeatedly across this style of shear: seal weep at the main closing cylinder after enough duty cycles, and slow cylinder drift under sustained load once seals start to go, which shows up as the jaw creeping open while holding a piece rather than staying clamped. Hose chafing at the pivot and mounting-ear area is the other common wear point, since those hoses flex on every open/close cycle. Neither symptom is usually urgent day one, but a drifting cylinder under load is a pinch-point safety concern — have your dealer verify seal condition and cylinder holding pressure rather than running it loaded.
What should I check before buying a used VHS-70?
Start with the serial prefix to pin down which generation and weight class you're actually looking at, since the name alone covers a wide spread of configurations. Then walk the blade edges for chipping or rounding and confirm how much indexing life is left before replacement is due. Check the jaw pivot and mounting-ear pins for play by hand and listen for knocking under a test cut. Cycle the main cylinder under load and watch for drift or weep at the rod seal. Finally confirm the mounting style (pin-on stick vs quick-coupler bracket) and carrier weight class actually match the excavator you intend to run it on — a mismatch on flow, pressure, or carrier class is the most common reason these show up for resale cheap. Have your dealer verify pin/bushing clearances and cylinder condition as part of any pre-purchase inspection.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific VHS-70 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.