Caterpillarwork toolshear-demolition/scrap
Caterpillar VHS-40
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar VHS-40 is a passive, excavator-mounted hydraulic demolition and scrap shear built by Verachtert under the Caterpillar Work Tools B.V. lineage, not a self-powered machine. It carries no engine, ECM, or onboard hydraulic reservoir of its own; the jaw's closing force comes entirely from the carrier excavator's auxiliary hydraulic circuit. Base-generation units (the H/M variants) run about 2.5 t (5,512 lb) operating weight with a 500 mm (19.7 in) jaw opening and roughly 5,100 kN (about 1,147,000 lbf) of cutting force at the jaw, sized for excavators in the 20 to 32 t class. The VHS-40 sits mid-pack in Caterpillar's Verachtert-built VHS-10/30/40/50/60/70 demolition-shear family, one size up from the VHS-30 and one size down from the VHS-50/60/70 siblings. A later /3-generation refresh (VHS-40/3), grouped in a parts-manual family covering VHS-30/3 through VHS-70/3, followed the base generation, though no independently confirmed weight or force figures are published for the VHS-40/3 itself. Both generations mount as a pin-on stick or boom tool with no dedicated quick-coupler variant offered specifically for this shear.
The VHS line's evolution across generations tracks a parts-manual reorganization more than a redesign of the shear's cutting geometry: a first-generation manual spanning VHS-10 through VHS-70 gave way to a /3-generation refresh covering the same family under new prefixes. No confirmed successor model is documented for the VHS-40 specifically; Caterpillar's current S-series mobile scrap and demolition shears occupy a similar carrier class and a dealer designation for the VHS-40 references the S325 line in some listings, but the VHS family kept selling and getting dealer support in parallel rather than being formally superseded. That lack of a clean supersession is exactly why the VHS-40 still matters in the used and parts market: with serial-prefix records thin and shared across siblings, buyers and parts counters lean on pin and bushing condition, blade wear, and weld integrity near the pin bosses to judge remaining life rather than on a model-year spec sheet. A structurally sound VHS-40 remains a viable working tool on 20-32 t carriers, and its resale value tracks hydraulic-seal and pivot condition far more than which generation badge it wears.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar VHS-40 specifications
Engine
| Power source | No onboard engine or ECM. VHS-40 is a passive, excavator-mounted hydraulic demolition/scrap shear that runs entirely off the carrier machine's auxiliary hydraulic circuit. |
Weights
| Operating weight (base H/M generation) | 2.5 t (5,512 lb). Not cross-verified against a second independent source — confirm with your dealer before ordering. |
| Operating weight (/3 generation, circa 2009-2012) | Not published for VHS-40/3 specifically. Sibling VHS-30/3 runs about 1.9 t and sibling VHS-50/3 about 4 t, so VHS-40/3 sits between them, but no source ties a specific figure to the VHS-40/3 name. |
| Shipping weight / ground pressure | Not separately published. As a passive attachment with no fluid reservoir, shipping weight is close to operating weight; ground pressure does not apply to a work tool. |
Dimensions
| Jaw opening (base generation) | 500 mm (19.7 in) |
| Carrier/excavator compatibility | 20 to 32 t class (about 22 to 35 US ton) excavators |
| Overall length / width | Not documented for this exact model in available spec listings — verify with dealer. Comparable siblings in this Verachtert scrap-shear line run roughly 2.2 to 2.5 m overall length, but no source ties a specific figure to the VHS-40 name itself, so it is left unstated rather than borrowed. |
Performance
| Cutting force (base generation) | 5,100 kN (about 1,147,000 lbf) at the jaw |
| Cutting force (/3 generation) | Not published for VHS-40/3 specifically — avoid borrowing sibling figures. |
| Travel speed / gradeability | Not applicable. This is a passive excavator-mounted work tool, not a self-propelled machine. |
Service capacities (summary)
| Fuel tank, engine oil, cooling system | None. The tool carries no engine, so these capacities do not apply. |
| Hydraulic system | No separate onboard reservoir. The shear draws hydraulic power directly from the carrier excavator's auxiliary circuit; specific working-pressure and flow requirements for this exact model are not documented in available spec sheets — check the carrier's work-tool hydraulic kit rating with your dealer. |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
VHS-40 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | Not applicable — the VHS-40 is a passive hydraulic demolition shear work tool with no onboard engine. | Not applicable. |
| Cooling system | Not applicable — no engine, no coolant circuit fitted to this attachment. | Not applicable. |
| Fuel tank | Not applicable — the shear carries no fuel system. | Not applicable. |
| Transmission / powertrain compartment | Not applicable — the shear has no drivetrain; jaw motion comes from the carrier's hydraulic cylinders only. | Not applicable. |
| Final drives (each) | Not applicable — no final drives on this work tool. | Not applicable. |
| Hydraulic system and tank | The shear has no dedicated hydraulic reservoir of its own. It runs on the flow and pressure supplied by the host excavator's hydraulic system, so no separate fill capacity is listed for the attachment in its own right. | Use whatever hydraulic oil grade the carrier excavator's own operation and maintenance manual calls for (typically an anti-wear hydraulic oil sized to the ambient temperature range). No shear-specific fluid brand is called out because the oil belongs to the host machine's circuit, not the attachment. |
| Axles / differentials | Not applicable — no axles or differentials on this attachment. | Not applicable. |
| Grease (pivot pins, bushings, jaw linkage) | No fill quantity is specified; service is by grease gun at each nipple until fresh grease purges from the joint, on a routine interval rather than a fixed volume. | General-purpose extreme-pressure chassis grease, NLGI grade 2, with moly (molybdenum disulfide) additive for the pin and bushing joints. Cooler climates call for a lighter-bodied grease of the same type; hot climates tolerate the standard-bodied version. No single named product is confirmed as the factory call-out specifically for the VHS-40 line in the sources checked — treat as a standard moly EP grease pending direct OMM confirmation. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar VHS-40 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
Servicing the VHS-40 beyond the schedule
Predictive Maintenance & Fluid Analysis
The VHS-40 has no engine or hydraulic reservoir of its own, so predictive care centers on trend data rather than oil sampling. Track pin and bushing clearance at every pivot on a set interval; a widening gap or a knock under load flags a joint headed for replacement before it scores the pin bore. Since the shear draws power from the carrier excavator, pull hydraulic fluid samples from the carrier's own circuit. Contamination or moisture there shows up as cylinder or rotator seal wear on the shear long before the excavator itself shows symptoms.
Corrective & Common Repairs
Blade replacement is the most common corrective job on the VHS-40: once an edge is chipped or rounded past shim range, swap the blade rather than reprofile it, since reshaping the bite geometry only shortens the next interval. Cylinder seal leaks trace back almost always to carrier hydraulic pressure set too high for the shear's rating, so confirm carrier relief settings before reseating a cylinder. Rough or jerky rotation points to worn rotator seals or a chafed hose; reroute with slack at full rotation when replacing it. Inspect welds near the pin bosses for cracks at every repair visit.
Overhaul & Rebuild Points
A structural rebuild on the VHS-40 centers on the pivot pins and bushings, the jaw pin, cylinder clevis, and rotator mount, all of which carry the full cutting load. Once measured play exceeds shim limits, replace pins and bushings as a set rather than one at a time; mismatched wear just accelerates the next failure. Rotator bearing service, reseal, repack, or full bearing replacement, belongs on the same overhaul cycle if seepage or drag has appeared. Have a dealer inspect and re-certify welds around the pin bosses and gussets before returning a rebuilt shear to hard demolition work.
Seasonal & Environment Servicing
Cold-climate operation calls for shorter grease intervals at the pin and bushing joints; cold grease migrates more slowly and leaves joints under-lubricated if the schedule doesn't tighten up. Switch to a lighter-bodied moly EP grease below freezing rather than forcing standard-bodied grease through the nipple. Hydraulic hoses stiffen in cold weather and are more prone to cracking at the rotator, so inspect routing and clamp points before each cold-season startup. In hot, dusty demolition environments, grease more often, since abrasive dust packed into a pin joint wears bushings faster than the standard interval assumes.
VHS-40 attachments & work tools
Carrier excavator weight class
VHS-40 is sized for excavators in roughly the 20 to 35 t class, one step up from the VHS-30 (15-25 t class) and one step down from VHS-50/60/70 in the same family. Published variants show slightly different carrier bands (about 20-32 t on one variant, about 20-35 t on another), so treat it as a range rather than a fixed cutoff and confirm against the carrier's own attachment-weight limit.
Mounting and coupler system
Mounts as a pin-on tool to the excavator stick (or boom-mounted on some carriers), matching the rest of the Cat/Verachtert mobile-shear range. There is no shear-specific quick-coupler built into the VHS-40 itself; using it through a tiltrotator or coupler depends on the bracket the coupler manufacturer offers for this shear's pin spacing and weight, not on a factory VHS-40 option.
Hydraulic supply requirements
Purely passive work tool: no engine, ECM, or onboard power pack. It draws all closing/opening force from the carrier excavator's auxiliary (attachment) hydraulic circuit, so the host machine needs an aux line and a shear-rated control valve already fitted. Exact flow and pressure figures specific to the VHS-40 name are not published in accessible dealer literature; these vary by carrier model and generation, so confirm the correct setting with the excavator dealer or shear manual rather than assume a single number.
Operating weight and jaw opening
Documented variants put operating weight at roughly 2.5 to 3 t with a jaw opening around 490 to 500 mm, consistent with its position between the smaller VHS-30 and the larger VHS-50/60/70 siblings. Cutting-force figures specific to the VHS-40 name were not found in accessible sources; do not borrow a sibling's cutting-force number for this model.
Blade and jaw arrangement
Like the rest of the Cat mobile scrap and demolition shear range, the cutting jaws use replaceable/reversible knife sections rather than a single fixed edge, letting a worn blade be indexed or swapped instead of replacing the whole jaw. No VHS-40-specific jaw-set (e.g., long-nose vs standard) options were confirmed in available sources.
Cylinder and frame guarding
The mobile-shear design family the VHS-40 belongs to shields the closing cylinder inside the shear frame and housing through the full cutting stroke, reducing exposure to falling debris during demolition work. This is a shared design trait of the product line rather than a documented standalone VHS-40 option.
Factory/family configuration note
VHS-40 sits in the Verachtert-built VHS-10/30/40/50/60/70 shear family (Caterpillar Work Tools B.V. lineage) and was later followed in Caterpillar's own current catalog naming by the S325 mobile scrap and demolition shear. That successor relationship is useful for tracing parts and dealer support lineage, but its specs should be kept separate from the VHS-40's own documented numbers.
All VHS-40 assemblies by section
Every catalogued assembly group for the Caterpillar VHS-40. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Frame And Body
243-1539 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***39 | Cover Group-Access | 1 |
242-9603 Cover Gp-Access
| 17***96 | Housing Group-Shear | 1 |
| 17***98 | Rotator Group-Hydraulic | 1 |
| 24***03 | Cover Group-Access | 1 |
242-2062 Cover Gp-Access
| 16***60 | Rotator Group-Hydraulic | 1 |
| 17***55 | Housing Group-Shear | 1 |
| 21***97 | Housing Group-Shear | 1 |
242-9605 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***05 | Cover Group-Access | 1 |
243-1540 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 1 |
| 24***40 | Cover Group-Access | 1 |
242-2063 Cover Gp-Access
| 16***60 | Rotator Group-Hydraulic | 1 |
| 18***99 | Housing Group-Shear | 1 |
| 21***96 | Housing Group-Shear | 1 |
242-3736 Cover Gp-Access
| 17***10 | Rotator Group-Hydraulic | 1 |
| 19***87 | Housing Group-Shear | 1 |
| 21***50 | Housing Group-Shear | 1 |
247-8415 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***15 | Cover Group-Access | 1 |
247-8416 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***16 | Cover Group-Access | 1 |
242-9604 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 1 |
| 24***04 | Cover Group-Access | 1 |
247-8418 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***18 | Cover Group-Access | 1 |
247-8417 Cover Gp-Access
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 24***58 | Latch Group-Access Door | 2 |
| 24***17 | Cover Group-Access | 1 |
227-4318 Guide Gp-Lines
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 22***18 | Guide Group-Lines | 1 |
| 24***58 | Latch Group-Access Door | 1 |
195-0777 Housing Gp-Shear
| 19***77 | Housing Group-Shear | 1 |
| 22***15 | Plate As | 1 |
| 6V***89 | Locknut; (M8x1.25-Thd) | 1 |
217-1396 Housing Gp-Shear
| 14***78 | Lockwasher | 24 |
| 15***21 | Lockwasher | 24 |
| 16***64 | Bolt-Socket Head; (M20x2.5x55-mm) | 24 |
216-6850 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 15***46 | Seal | 1 |
171-5496 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 17***96 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 2 |
245-8017 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
318-9776 Housing Gp-Shear
| 14***78 | Lockwasher | 24 |
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 24 |
196-2019 Housing Gp-Shear
| 08***10 | Setscrew; (M10x21-mm) | 6 |
| 10***88 | Bolt-Socket Head; (M10x1.5x16-mm) | 3 |
| 15***18 | Lockwasher | 6 |
217-1398 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 11***73 | Seal; (0.5cm) (X2) | 0 |
318-9778 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 10 |
| 15***21 | Lockwasher | 18 |
177-3355 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 17***55 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 2 |
318-9773 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 14***78 | Lockwasher | 24 |
| 15***19 | Lockwasher | 2 |
217-1397 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 10 |
| 15***21 | Lockwasher | 18 |
184-3399 Housing Gp-Shear
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 18***99 | Housing Group-Shear | 1 |
| 24***58 | Latch Group-Access Door | 1 |
245-8016 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 11***73 | Seal; (0.5cm) (X2) | 0 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
217-1395 Housing Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 46 |
| 15***21 | Lockwasher | 18 |
197-7187 Housing Gp-Shear
| 10***40 | Plug | 1 |
| 15***46 | Seal | 1 |
| 15***18 | Lockwasher | 8 |
235-0577 Housing Gp-Shear
| 09***07 | Bolt; (M16x2x120-mm) | 8 |
| 10***40 | Plug | 1 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
242-2058 Latch Gp-Access Door
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 34 |
| 16***12 | Clip; (Slot) | 2 |
171-5558 Mounting Gp-Shear
| 14***52 | Elbow As. | 2 |
| 15***19 | Lockwasher | 2 |
| 15***21 | Lockwasher | 18 |
Hydraulic System
184-3404 Cylinder & Lines Gp-Shear
| 18***04 | Cylinder & Lines Group-Shear | 1 |
| 28***28 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
187-2996 Cylinder & Lines Gp-Shear
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
| 17***60 | Cylinder Group-Shear | 1 |
187-2962 Cylinder & Lines Gp-Shear
| 17***35 | Mounting Group-Cylinder | 1 |
| 17***49 | Lines Group-Cylinder | 1 |
| 17***54 | Cylinder & Lines Group-Shear | 1 |
171-5497 Cylinder & Lines Gp-Shear
| 09***69 | Bolt | 24 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
177-3369 Cylinder & Lines Gp-Shear
| 10***86 | Spring | 1 |
| 17***69 | Cylinder & Lines Group-Shear | 1 |
| 24***59 | Latch | 1 |
196-2026 Cylinder & Lines Gp-Shear
| 12***11 | Hose As | 1 |
| 16***54 | Seal | 1 |
| 16***16 | Seal | 1 |
222-8828 Cylinder & Lines Gp-Shear
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 8 |
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
171-5554 Cylinder & Lines Gp-Shear
| 09***69 | Bolt | 24 |
| 14***92 | Elbow; (-12 Orfs/-12 Orfs Swivel) | 2 |
| 15***46 | Seal | 1 |
222-8830 Cylinder & Lines Gp-Shear
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
| 18***78 | Cylinder Group-Shear | 1 |
177-3360 Cylinder & Valve Gp
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
| 17***60 | Cylinder & Valve Group | 1 |
196-2022 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
187-2993 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
187-2945 Cylinder & Valve Gp
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
184-3403 Cylinder & Valve Gp
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 8 |
| 16***16 | Seal | 1 |
| 17***21 | Adapter As | 1 |
187-2978 Cylinder Gp-Shear
| 16***16 | Seal | 1 |
| 16***03 | Bushing | 2 |
| 17***23 | Plug As | 2 |
177-3368 Cylinder Gp-Shear
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***19 | Lockwasher | 2 |
184-3405 Cylinder Gp-Shear
| 14***06 | Bolt-Socket Head; (M20x2.5x140-mm) | 5 |
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
196-2030 Cylinder Gp-Shear
| 16***16 | Seal | 1 |
| 16***03 | Bushing | 2 |
| 17***23 | Plug As | 2 |
171-5560 Cylinder Gp-Shear
| 14***78 | Lockwasher | 1 |
| 14***51 | Elbow Group | 1 |
| 15***18 | Lockwasher | 2 |
318-4547 Lines Gp-Connecting
| 16***46 | Bar-Clamp | 2 |
| 16***90 | Clip; (Slot) | 2 |
| 16***91 | Clip; (Tab) | 2 |
171-5565 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***87 | Bushing | 2 |
197-6880 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***41 | Bushing | 2 |
291-1280 Lines Gp-Connecting
| 12***40 | Fitting As-Hydraulic; (Quick Disconnect, Male) | 2 |
| 17***33 | Hose As | 2 |
| 29***80 | Lines Group-Connecting | 1 |
225-2729 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 17***23 | Plug As | 4 |
242-1184 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 09***06 | Bolt-Socket Head; (M16x2x80-mm) | 24 |
| 16***16 | Seal | 1 |
201-7607 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 14***84 | Bolt-Socket Head; (M20x2.5x110-mm) | 22 |
| 16***16 | Seal | 1 |
292-1512 Lines Gp-Connecting
| 19***69 | Hose As | 2 |
| 1P***05 | Seal (Check Valve Outlet) | 4 |
| 29***12 | Lines Group-Connecting | 1 |
241-5636 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 16***16 | Seal | 1 |
| 16***87 | Bushing | 2 |
177-5026 Lines Gp-Connecting
| 09***48 | Nipple, Grease | 1 |
| 09***06 | Bolt-Socket Head; (M16x2x80-mm) | 24 |
| 16***16 | Seal | 1 |
242-1185 Lines Gp-Connecting
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 2 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 14***18 | Reducer; (-8orfs/-12orfs Swivel) | 2 |
171-5549 Lines Gp-Cylinder
| 17***49 | Lines Group-Cylinder | 1 |
| 24***84 | Lines Group-Connecting | 1 |
| 24***85 | Lines Group-Connecting | 1 |
170-2174 Manifold Gp-Control
| 17***74 | Manifold Group-Control | 1 |
| 24***38 | Hose As | 2 |
| 6V***98 | Seal-O-Ring -Line From Gear Pump Output | 2 |
170-2172 Motor & Manifold Gp-Rotator
| 16***43 | Seal | 1 |
| 17***72 | Motor & Manifold Group-Rotator | 1 |
| 17***05 | Adapter As | 2 |
216-7650 Motor Gp-Gerotor
| 1P***04 | Seal - Rectangular (45mm Dia) | 1 |
| 1P***67 | Flange-Half (43.31 mm Id) | 2 |
| 21***50 | Motor Group-Gerotor | 1 |
170-2173 Motor Gp-Gerotor
| 10***36 | Connector | 2 |
| 10***37 | Seal | 1 |
| 15***94 | Adapter As | 2 |
320-1326 Motor Gp-Gerotor
| 29***43 | Hose As | 2 |
| 29***45 | Hose As | 2 |
| 32***26 | Motor Group-Gerotor | 1 |
171-5535 Mounting Gp-Cylinder
| 17***35 | Mounting Group-Cylinder | 1 |
| 32***36 | Hose As | 2 |
| 32***37 | Hose As | 2 |
216-7649 Rotator Gp-Hydraulic
| 03***43 | Seal-O-Ring | 1 |
| 08***09 | Spacer; (16.6x32x8.5-mm Thk) | 34 |
| 12***28 | Adaptor - Includes:- | 2 |
171-7526 Rotator Gp-Hydraulic
| 17***21 | Kit-Housing | 1 |
| 17***22 | Shaft-Output | 1 |
| 17***25 | Key-Square | 1 |
319-2123 Rotator Gp-Hydraulic
| 09***07 | Nut; (M12x1.75-Thd) | 4 |
| 14***53 | Plug | 1 |
| 18***82 | Bolt-Socket Head; (M20x2.5x65-mm) | 16 |
171-5555 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***74 | Manifold Group-Control | 1 |
| 17***76 | Ring-Mounting | 1 |
171-5498 Rotator Gp-Hydraulic
| 14***20 | Bolt-Socket Head; (M6x1x75-mm) | 4 |
| 17***98 | Rotator Group-Hydraulic | 1 |
| 7Y***19 | Seal-O-Ring (Id=12.37mm) | 2 |
194-6068 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***74 | Manifold Group-Control | 1 |
| 17***77 | Gear-Drive; (15-Teeth) | 1 |
319-2124 Rotator Gp-Hydraulic
| 03***43 | Seal-O-Ring | 1 |
| 09***48 | Nipple, Grease | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
171-8110 Rotator Gp-Hydraulic
| 17***73 | Motor Group-Gerotor | 1 |
| 17***76 | Ring-Mounting | 1 |
| 17***77 | Gear-Drive; (15-Teeth) | 1 |
169-6060 Rotator Gp-Hydraulic
| 15***35 | Elbow As | 4 |
| 15***18 | Lockwasher | 2 |
| 15***19 | Lockwasher | 1 |
217-1423 Rotator Gp-Hydraulic
| 15***94 | Adapter As | 2 |
| 15***44 | Seal | 1 |
| 15***46 | Seal | 1 |
265-6468 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 16 |
| 12***28 | Adaptor - Includes:- | 4 |
| 12***24 | Seal-O-Ring; (12.37mm Id) | 4 |
172-1124 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 8 |
| 12***28 | Adaptor - Includes:- | 4 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 4 |
170-3045 Swivel Gp
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 16 |
| 12***28 | Adaptor - Includes:- | 4 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 4 |
208-8451 Valve Gp-Control
| 08***72 | Seal-O-Ring | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 15***94 | Adapter As | 6 |
174-4901 Valve Gp-Control -Quick
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 8 |
| 12***28 | Adaptor - Includes:- | 4 |
| 12***24 | Seal-O-Ring; (12.37mm Id) | 4 |
172-2207 Valve Gp-Speed Control
| 16***43 | Seal | 1 |
| 17***41 | Stator | 1 |
| 17***42 | Rotor | 1 |
208-5125 Valve Gp-Speed Control
| 16***43 | Seal | 1 |
| 17***57 | Plug As | 4 |
| 17***14 | Stator | 1 |
170-3229 Valve Gp-Speed Control
| 08***72 | Seal-O-Ring | 1 |
| 14***70 | Elbow, 90°,-8 Orb Swiv. /-8 Orfs | 2 |
| 15***94 | Adapter As | 6 |
Service Equipment And Supplies
200-2135 Film Gp
| 09***01 | Bolt-Socket Head; (M8x1.25x40-mm) | 4 |
| 17***55 | Seal-O-Ring | 2 |
| 20***35 | Film Group | 1 |
200-8571 Film Gp
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
197-7184 Film Gp
| 17***30 | Plug | 6 |
| 17***31 | Valve | 1 |
| 17***32 | Plug-Screw | 2 |
197-3519 Film Gp
| 13***54 | Plug As | 3 |
| 19***19 | Film Group | 1 |
| 20***87 | Slack Adjuster Group | 1 |
195-0776 Film Gp
| 16***80 | Kit-Service; (Counterbalance Valve) | 2 |
| 18***01 | Manifold | 1 |
| 18***02 | Valve | 1 |
197-3843 Film Gp
| 17***30 | Plug | 6 |
| 17***31 | Valve | 1 |
| 17***32 | Plug-Screw | 2 |
200-2134 Kit-Maintenance
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
235-0605 Kit-Maintenance
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
184-3400 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 15***35 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 15***36 | Film-Warning; (Read Operation Manual) | 2 |
197-7186 Kit-Maintenance
| 14***08 | Fitting | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
183-5625 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
177-3356 Kit-Maintenance
| 14***36 | Film-Warning; (Flying Debris) | 2 |
| 14***69 | Film-Warning; (Alert) | 2 |
| 14***70 | Film-Warning; (Read Omm) | 2 |
195-0775 Kit-Maintenance
| 14***08 | Fitting | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
235-2730 Kit-Maintenance
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
235-2732 Kit-Maintenance
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
200-2959 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
200-2960 Lock Gp-Shear
| 14***74 | Fitting As | 2 |
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
199-8486 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
200-2962 Lock Gp-Shear
| 20***62 | Lock Group-Shear | 1 |
200-2885 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 17***03 | Wrench-T-Handle | 1 |
200-2961 Lock Gp-Shear
| 14***86 | Fitting As | 2 |
| 15***44 | Seal | 1 |
| 16***92 | Wrench | 1 |
Work Tool Arrangement
200-2133 Shear Ar-Hydraulic
| 19***17 | Shear Group-Hydraulic | 1 |
| 20***33 | Shear Ar-Hydraulic | 1 |
| 20***34 | Kit-Maintenance | 1 |
200-8570 Shear Ar-Hydraulic
| 18***25 | Kit-Maintenance | 1 |
| 19***30 | Shear Group-Hydraulic | 1 |
| 20***70 | Shear Ar-Hydraulic | 1 |
197-7182 Shear Ar-Hydraulic
| 19***82 | Shear Ar-Hydraulic | 1 |
| 19***84 | Film Group | 1 |
| 19***85 | Shear Group-Hydraulic | 1 |
197-3842 Shear Ar-Hydraulic
| 18***00 | Kit-Maintenance | 1 |
| 19***42 | Shear Ar-Hydraulic | 1 |
| 19***43 | Film Group | 1 |
195-0772 Shear Ar-Hydraulic
| 19***72 | Shear Ar-Hydraulic | 1 |
| 19***74 | Shear Group-Hydraulic | 1 |
| 19***75 | Kit-Maintenance | 1 |
197-3518 Shear Ar-Hydraulic
| 17***56 | Kit-Maintenance | 1 |
| 19***18 | Shear Ar-Hydraulic | 1 |
| 19***19 | Film Group | 1 |
Work Tools
200-7803 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 20***03 | Bracket Group-Mounting | 1 |
| 20***09 | Bracket Group-Mounting | 1 |
169-4974 Bracket Gp-Mounting
| 16***74 | Bracket Group-Mounting | 1 |
| 16***93 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
175-3014 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 17***14 | Bracket Group-Mounting | 1 |
| 17***51 | Bracket Group-Mounting | 1 |
169-4976 Bracket Gp-Mounting
| 16***76 | Bracket Group-Mounting | 1 |
| 16***96 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
283-4827 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 23***25 | Plate-Serial Number | 1 |
| 28***27 | Bracket Group-Mounting | 2 |
200-7804 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***04 | Bracket Group-Mounting | 1 |
| 20***10 | Bracket Group-Mounting | 1 |
247-0536 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 15***21 | Lockwasher | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
200-7805 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***05 | Bracket Group-Mounting | 1 |
| 20***11 | Bracket Group-Mounting | 1 |
205-3923 Bracket Gp-Mounting
| 20***23 | Bracket Group-Mounting | 1 |
| 20***46 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
257-1041 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***41 | Bracket Group-Mounting | 1 |
276-7982 Bracket Gp-Mounting
| 15***97 | Seal-Lip Type | 2 |
| 19***46 | Insert | 1 |
| 26***24 | Bearing-Sleeve | 2 |
291-1291 Bracket Gp-Mounting
| 15***19 | Lockwasher | 8 |
| 16***95 | Seal; (Id=93.00mm) | 2 |
| 22***89 | Bearing-Sleeve | 2 |
169-4970 Bracket Gp-Mounting
| 16***70 | Bracket Group-Mounting | 1 |
| 16***90 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
254-4039 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***71 | Washer; (26x90x8-mm Thk) | 1 |
197-7840 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***39 | Bracket As | 1 |
169-4968 Bracket Gp-Mounting
| 16***68 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 23***05 | Bracket As | 1 |
283-4828 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
169-4969 Bracket Gp-Mounting
| 16***69 | Bracket Group-Mounting | 1 |
| 16***89 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
198-7615 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***15 | Bracket Group-Mounting | 1 |
| 19***16 | Bracket Group-Mounting | 1 |
169-5308 Bracket Gp-Mounting
| 16***08 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***45 | Bracket Group-Mounting | 1 |
169-5311 Bracket Gp-Mounting
| 16***11 | Bracket Group-Mounting | 1 |
| 16***16 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
179-1653 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 17***16 | Bracket As | 1 |
197-5353 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
| 19***53 | Bracket Group-Mounting | 1 |
175-0342 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***42 | Bracket Group-Mounting | 1 |
| 17***49 | Bracket As | 1 |
200-7811 Bracket Gp-Mounting
| 09***34 | Shim; (T=69.85mm) | 2 |
| 11***82 | Bearing-Sleeve | 2 |
| 15***19 | Lockwasher | 16 |
299-0293 Bracket Gp-Mounting
| 17***09 | Edge-Cutting | 2 |
| 17***10 | Edge-Cutting | 2 |
| 17***11 | Cutter | 1 |
169-4967 Bracket Gp-Mounting
| 16***67 | Bracket Group-Mounting | 1 |
| 16***86 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
224-2478 Bracket Gp-Mounting
| 22***78 | Bracket Group-Mounting | 1 |
| 24***32 | Bracket Group-Mounting | 1 |
249-3132 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 2 |
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
175-0338 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***38 | Bracket Group-Mounting | 1 |
| 17***46 | Bracket Group-Mounting | 1 |
254-4463 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***71 | Washer; (26x90x8-mm Thk) | 2 |
| 25***63 | Bracket Group-Mounting | 1 |
257-1047 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 25***47 | Bracket Group-Mounting | 1 |
| 27***38 | Bracket As | 1 |
222-8513 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 22***13 | Bracket Group-Mounting | 1 |
| 22***78 | Bracket Group-Mounting | 1 |
245-8009 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 20***59 | Plate-Serial Number | 1 |
257-0101 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***01 | Bracket Group-Mounting | 1 |
257-0099 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***99 | Bracket Group-Mounting | 1 |
| 25***02 | Bracket Group-Mounting | 1 |
179-1651 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 17***18 | Bracket As | 1 |
248-7980 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 24***80 | Bracket Group-Mounting | 1 |
222-3345 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 16 |
| 22***45 | Bracket Group-Mounting | 1 |
| 22***11 | Bracket Group-Mounting | 1 |
199-1258 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
202-0285 Bracket Gp-Mounting
| 17***61 | Cover | 2 |
| 20***84 | Bracket As | 1 |
| 20***85 | Bracket Group-Mounting | 1 |
201-9466 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***97 | Plate-Cover | 1 |
| 20***66 | Bracket Group-Mounting | 1 |
200-7807 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 20***07 | Bracket Group-Mounting | 1 |
257-0098 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 25***98 | Bracket Group-Mounting | 1 |
255-0001 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***01 | Bracket Group-Mounting | 1 |
| 25***99 | Bracket Group-Mounting | 1 |
169-4971 Bracket Gp-Mounting
| 16***71 | Bracket Group-Mounting | 1 |
| 16***91 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
291-4097 Bracket Gp-Mounting
| 15***19 | Lockwasher | 8 |
| 29***97 | Bracket Group-Mounting | 1 |
| 29***22 | Bracket As | 1 |
169-4981 Bracket Gp-Mounting
| 16***81 | Bracket Group-Mounting | 1 |
| 16***99 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
291-5775 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 29***75 | Bracket Group-Mounting | 1 |
253-7830 Bracket Gp-Mounting
| 09***49 | Washer; (22x60x6-mm Thk) | 1 |
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
287-6820 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 28***20 | Bracket Group-Mounting | 1 |
| 29***75 | Bracket Group-Mounting | 1 |
275-9776 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 27***76 | Bracket Group-Mounting | 1 |
| 27***83 | Bracket As | 1 |
180-1286 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 18***86 | Bracket Group-Mounting | 1 |
| 19***94 | Bracket Group-Mounting | 1 |
199-0719 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 16 |
| 19***40 | Bracket Group-Mounting | 1 |
| 19***19 | Bracket Group-Mounting | 1 |
222-8507 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 22***07 | Bracket Group-Mounting | 1 |
| 22***13 | Bracket Group-Mounting | 1 |
201-5013 Bracket Gp-Mounting
| 09***54 | Seal; (Id=79.85mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
169-5307 Bracket Gp-Mounting
| 16***07 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***47 | Bracket Group-Mounting | 1 |
222-8508 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
275-8137 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 27***37 | Bracket Group-Mounting | 1 |
| 27***77 | Bracket As | 1 |
169-4978 Bracket Gp-Mounting
| 16***78 | Bracket Group-Mounting | 1 |
| 16***97 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
222-8512 Bracket Gp-Mounting
| 14***90 | Bearing-Sleeve; (140.26mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
291-1266 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 29***66 | Bracket Group-Mounting | 1 |
| 29***97 | Bracket Group-Mounting | 1 |
197-5352 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 48 |
| 19***52 | Bracket Group-Mounting | 1 |
| 19***53 | Bracket Group-Mounting | 1 |
179-1645 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***18 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
175-3012 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 17***12 | Bracket Group-Mounting | 1 |
| 17***53 | Bracket Group-Mounting | 1 |
200-7802 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***02 | Bracket Group-Mounting | 1 |
| 20***08 | Bracket Group-Mounting | 1 |
199-1259 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 19***58 | Bracket Group-Mounting | 1 |
| 19***59 | Bracket Group-Mounting | 1 |
246-9991 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 24***91 | Bracket Group-Mounting | 1 |
179-1646 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***97 | Plate-Cover | 1 |
| 17***45 | Bracket As | 1 |
169-4980 Bracket Gp-Mounting
| 16***80 | Bracket Group-Mounting | 1 |
| 16***98 | Bracket As | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
202-0286 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 48 |
| 20***85 | Bracket Group-Mounting | 1 |
| 20***86 | Bracket Group-Mounting | 1 |
217-0996 Bracket Gp-Mounting
| 15***19 | Lockwasher | 18 |
| 17***61 | Cover | 2 |
| 21***96 | Bracket Group-Mounting | 1 |
205-3920 Bracket Gp-Mounting
| 20***20 | Bracket Group-Mounting | 1 |
| 20***70 | Bracket As | 1 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
283-4186 Bracket Gp-Mounting
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 28***86 | Bracket Group-Mounting | 2 |
| 7X***62 | Capscrew, Hex Head (Hm20 - 2.5 X 50 mm, G8) | 6 |
200-7806 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 20***06 | Bracket Group-Mounting | 1 |
201-5015 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***13 | Bracket Group-Mounting | 1 |
| 20***15 | Bracket Group-Mounting | 1 |
198-7616 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***13 | Bracket As | 1 |
222-8506 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 22***06 | Bracket Group-Mounting | 1 |
| 22***12 | Bracket Group-Mounting | 1 |
336-0800 Bracket Gp-Mounting
| 14***87 | Screw-Flat Head | 2 |
| 14***75 | Bolt; (M20x2.5x75-Thd) | 6 |
| 16***85 | Edge-Cutting | 4 |
200-7801 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***01 | Bracket Group-Mounting | 1 |
| 20***07 | Bracket Group-Mounting | 1 |
200-7808 Bracket Gp-Mounting
| 13***17 | Bearing-Sleeve; (116.23mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 16***96 | Seal; (Id=99.85mm) | 2 |
179-1647 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***19 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
222-8511 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 22***11 | Bracket Group-Mounting | 1 |
200-7800 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***00 | Bracket Group-Mounting | 1 |
| 20***06 | Bracket Group-Mounting | 1 |
179-1654 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***15 | Bracket As | 1 |
| 16***97 | Plate-Cover | 1 |
201-5014 Bracket Gp-Mounting
| 09***54 | Seal; (Id=79.85mm) | 2 |
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
199-7008 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***07 | Bracket Group-Mounting | 1 |
| 19***08 | Bracket Group-Mounting | 1 |
200-7506 Bracket Gp-Mounting
| 15***18 | Lockwasher | 8 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 16***97 | Plate-Cover | 1 |
175-0341 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***41 | Bracket Group-Mounting | 1 |
| 17***48 | Bracket As | 1 |
200-7809 Bracket Gp-Mounting
| 14***90 | Bearing-Sleeve; (140.26mm Od) | 2 |
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
201-5016 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 20***14 | Bracket Group-Mounting | 1 |
| 20***16 | Bracket Group-Mounting | 1 |
199-7007 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 18***74 | Cover | 2 |
| 19***06 | Bracket As | 1 |
257-0102 Bracket Gp-Mounting
| 17***90 | Bolt-Socket Head; (M20x2.5x70-mm) | 36 |
| 25***02 | Bracket Group-Mounting | 1 |
| 25***47 | Bracket Group-Mounting | 1 |
193-4497 Bracket Gp-Mounting
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 19***97 | Bracket Group-Mounting | 1 |
| 20***66 | Bracket Group-Mounting | 1 |
283-4187 Bracket Gp-Mounting
| 15***97 | Seal-Lip Type | 2 |
| 19***46 | Insert | 1 |
| 26***24 | Bearing-Sleeve | 2 |
200-7810 Bracket Gp-Mounting
| 09***34 | Shim; (T=69.85mm) | 2 |
| 11***82 | Bearing-Sleeve | 2 |
| 15***19 | Lockwasher | 16 |
193-9094 Bracket Gp-Mounting
| 15***19 | Lockwasher | 16 |
| 17***61 | Cover | 2 |
| 19***94 | Bracket Group-Mounting | 1 |
224-2477 Bracket Gp-Mounting
| 15***18 | Lockwasher | 6 |
| 17***33 | Cover | 1 |
| 22***77 | Bracket Group-Mounting | 1 |
169-5312 Bracket Gp-Mounting
| 16***12 | Bracket Group-Mounting | 1 |
| 16***82 | Bolt-Socket Head; (M24x3x70-mm) | 14 |
| 17***54 | Bracket Group-Mounting | 1 |
197-7455 Edge Gp-Cutting
| 11***30 | Bolt-Socket Head; (M20x2.5x150-mm) | 4 |
| 14***66 | Screw-Flat Head; (M24x3x160-mm) | 9 |
| 14***25 | Screw-Flat Head | 9 |
195-0780 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 7 |
| 14***87 | Screw-Flat Head | 7 |
| 16***74 | Shim; (0.5-mm Thk) | 10 |
184-7651 Edge Gp-Cutting
| 14***66 | Screw-Flat Head; (M24x3x160-mm) | 9 |
| 14***25 | Screw-Flat Head | 9 |
| 17***81 | Edge-Cutting | 1 |
217-1412 Edge Gp-Cutting
| 14***78 | Lockwasher | 3 |
| 17***80 | Bolt-Socket Head; (M20x2.5x120-mm) | 3 |
| 21***12 | Edge Group-Cutting | 1 |
234-9152 Edge Gp-Cutting
| 19***00 | Bar | 1 |
| 23***52 | Edge Group-Cutting | 1 |
| 8T***89 | Locknut; (M10x1.15-Thd) | 2 |
177-3359 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 14 |
| 14***81 | Screw-Flat Head | 3 |
| 16***85 | Edge-Cutting | 1 |
236-2204 Edge Gp-Cutting
| 20***86 | Plate-Lock | 2 |
| 23***04 | Edge Group-Cutting | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
216-7648 Edge Gp-Cutting
| 14***98 | Screw-Flat Head; (M20x2.5x90-mm) | 12 |
| 14***87 | Screw-Flat Head | 3 |
| 15***21 | Lockwasher | 3 |
171-5499 Edge Gp-Cutting
| 14***98 | Screw-Flat Head; (M20x2.5x90-mm) | 12 |
| 14***87 | Screw-Flat Head | 3 |
| 16***85 | Edge-Cutting | 1 |
217-1413 Edge Gp-Cutting
| 11***30 | Bolt-Socket Head; (M20x2.5x150-mm) | 4 |
| 14***78 | Lockwasher | 4 |
| 21***13 | Edge Group-Cutting | 1 |
234-1339 Edge Gp-Cutting
| 14***78 | Lockwasher | 3 |
| 17***93 | Bolt-Socket Head; (M20x2.5x80-mm) | 3 |
| 22***49 | Plate-Wear | 1 |
217-1410 Edge Gp-Cutting
| 14***87 | Screw-Flat Head | 2 |
| 14***75 | Bolt; (M20x2.5x75-Thd) | 6 |
| 15***21 | Lockwasher | 3 |
196-2023 Edge Gp-Cutting
| 14***15 | Screw-Flat Head; (M20x2.5x100-mm) | 7 |
| 14***87 | Screw-Flat Head | 7 |
| 14***78 | Lockwasher | 3 |
197-3844 Shear Gp-Hydraulic
| 19***44 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
197-3520 Shear Gp-Hydraulic
| 19***20 | Shear Group-Hydraulic | 1 |
| 20***17 | Plate-Lock | 2 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
197-7185 Shear Gp-Hydraulic
| 17***26 | Rotator Group-Hydraulic | 1 |
| 19***77 | Housing Group-Shear | 1 |
| 19***85 | Shear Group-Hydraulic | 1 |
199-8930 Shear Gp-Hydraulic
| 19***68 | Rotator Group-Hydraulic | 1 |
| 19***19 | Housing Group-Shear | 1 |
| 19***30 | Shear Group-Hydraulic | 1 |
195-0774 Shear Gp-Hydraulic
| 19***74 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
196-2017 Shear Gp-Hydraulic
| 19***17 | Shear Group-Hydraulic | 1 |
| 8T***32 | Nut (M16 X 2 Thd); (M16x2.00 Thd) | 2 |
| 8T***75 | Bolt; (M16x2x90-mm) | 1 |
Frequently asked questions
Does the Caterpillar VHS-40 have its own engine?
No. The VHS-40 is a passive, purely hydro-mechanical demolition shear with no engine, ECM, or onboard power pack. It draws all closing and opening force from the carrier excavator's auxiliary hydraulic circuit, so there is no engine spec, fuel system, or fault-code system belonging to the shear itself.
What is the operating weight of the VHS-40?
The base H/M generation runs about 2.5 t (5,512 lb). That figure varies by generation and configuration: no independently confirmed weight has been published for the later VHS-40/3 refresh specifically, so treat the base figure as a starting point and confirm the exact unit's weight against its own data plate or dealer records.
What replaced the Caterpillar VHS-40?
No confirmed successor model is documented. The VHS family continued in parallel through a /3-generation refresh (VHS-40/3) rather than being retired in favor of a distinct new model, and some listings pair the VHS-40 with Caterpillar's current S325 mobile shear as a comparable dealer designation, but that is not a documented formal supersession.
What VHS-40 owners discuss
What wear pattern do operators report on the VHS-40's blades before they need replacing?
Blade clearance opens up before the edge looks visibly worn. The gap between opposing blades gets checked with a feeler gauge on a routine basis rather than waiting for a rounded edge to show. Shimming behind the blade restores clearance for a while, but once an edge is chipped or the profile is rounded past the shim range, the blade gets swapped rather than ground, since reshaping the bite geometry shortens the next service interval instead of extending it.
How much pin and bushing play is normal before it needs attention?
Same rule as any pivot-heavy attachment: daily grease at the jaw pivot and the frame-to-cylinder clevis is what separates a shear that goes a long service life from one that eats bushings every season. Play shows up first as a knock or clunk when the jaw changes direction under load. Clearance gets checked on a set schedule with a pry bar or feeler gauge rather than waiting for noise, because by the time it's audible the bushing is usually gone and the pin bore is at risk of scoring.
Why does the shear feel weak or slow even though the blades look fine?
Consensus is that sluggish or weak cutting is rarely the shear's own fault, it is almost always the carrier excavator's auxiliary circuit being undersized or out of adjustment for it. Flow and relief pressure on the aux circuit get confirmed against what the shear calls for before anything on the tool itself is blamed. Running it starved of flow just slows the cycle, but running it on too much pressure is what tears up cylinder seals early, so the fix is calibration, not parts.
What causes rough or jerky rotation on the shear?
The rotation drive is the item most likely to draw a service call on this class of attachment. Slow or jerky rotation under load traces back most often to worn rotator seals or a hose routed too tight through the rotation range, chafing itself through in one season. The routing fix, giving the hose enough slack and a clamp pattern that doesn't pinch it at full rotation, prevents the repeat failure that a seal-only repair misses.
Are cracked welds near the pin bosses something to worry about?
Yes. Fatigue cracking near the pin bosses and gusset welds shows up on shears worked hard against reinforced concrete or heavy structural steel. A crack radiating from a pin bore or a cracked gusset weld is a structural warning, not a cosmetic one, and it usually means a pin or bushing was already loose, or the shear was run past what its frame is built for. Grinding and re-welding without fixing the root cause is a temporary patch. Because this is a load-bearing structural repair, have your dealer verify the weld procedure and inspect the surrounding frame before the tool goes back into service.
Does the VHS-40 have any onboard electronics or fault codes to watch?
No. It is a purely hydro-mechanical attachment, no engine, no ECM, no sensors of its own, it runs entirely off the carrier excavator's auxiliary hydraulic circuit. Every symptom owners chase, weak force, slow cycle, rough rotation, knock in the jaw, shows up as a mechanical or hydraulic clue rather than a code, so diagnosis starts with flow and pressure checks at the carrier and a hands-on inspection of pins, blades, and hoses rather than a diagnostic scan.
What should a buyer check on a used VHS-40 before making an offer?
Walk the pins and bushings first for play at every pivot, then look at the jaw for alignment (blades should meet flush across the full stroke, not twist or bind partway through). Check blade clearance and edge condition, look closely for chipped teeth or a rounded profile that is already past shim range. Inspect welds around the pin bosses and gussets for cracks or prior repair grinding. Cycle the rotation function and look for seepage at the rotator seals and cylinder glands, and flex the hoses at full rotation to check for chafe marks. Any combination of loose pins, cracked welds, and leaking seals on the same unit points to a shear that has been run hard and under-maintained.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific VHS-40 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.