Caterpillarengine - generator setpower module
Caterpillar PMG3516
Maintenance schedule, common problems & OEM parts breakdown
The Cat PMG3516 is a gas-engine power module built around the 16-cylinder, four-stroke, spark-ignited 3516 (G3516) natural gas engine platform rather than a diesel block. It is packaged as a skid-mounted power module or generator set, with typical skid weights running roughly 9,000 to 22,000 kg (20,000 to 49,000 lb) depending on generator-end size, enclosure, and power rating. Typical work is oilfield and gas-plant duty: gas lift, gas gathering, and wellhead gas compression drive packages, plus prime, continuous, and standby electric power for drilling rigs, gas processing sites, and remote or off-grid facilities. Cat offers the base engine in naturally aspirated, turbocharged-aftercooled, and low-emission stoichiometric configurations with three-way catalyst, along with heavy-duty variants built for sour or lower-quality field gas, mounted open-skid or in a sound/weather enclosure with radiator or remote cooling.
The 3516 gas engine platform spans three control-system generations under one basic architecture. The original 3516/G3516 used the ADEM A3 engine management system, integrating ignition, governing, and detonation-sensitive timing control. The 3516B moved to ADEM III, adding sharper emissions control and more configurable ratings, including dual-fuel and blending variants for gensets. The 3516C advanced further to ADEM A4, folding speed governing, air/fuel ratio control, and ignition/detonation management into a single module alongside heavy-duty sour-gas ratings and higher continuous output. Because a PMG3516 nameplate can cover any of these three generations, the module matters in the used and parts market mainly as a source of long-running, field-proven gas-compression and generation capacity — but buyers and parts sourcers need to confirm the exact engine arrangement and serial prefix before assuming ignition, ECM, or emissions hardware interchanges between a base 3516, a 3516B, and a 3516C.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar PMG3516 specifications
Engine
| Engine family | Cat G3516 series V-16, 4-stroke-cycle, spark-ignited natural gas engine. The PMG3516 power module has been built across several G3516 generations (G3516, G3516B, G3516C) depending on production run/serial prefix, not a single fixed engine build. |
| Configuration | V-16, turbocharged, aftercooled (TA/LE low-emission variants); digital engine management on later builds |
| Gross power (varies by rating/series) | Roughly 858-999 bkW (1150-1340 bhp) at 1200-1400 rpm for early G3516 LE builds, up to about 1012-1555 kW at 1800 rpm on later G3516C-based ratings. Exact continuous/standby rating depends on fuel quality, altitude, and the specific power-module rating sheet — treat as a range, not a fixed number. |
| Displacement | 69 L (4210 cu in) |
| Bore x stroke | 170 mm x 190 mm (6.7 in x 7.5 in) |
| Cylinders | 16, V-configuration |
| Compression ratio | About 11:1 to 11.3:1, varies slightly by series (G3516B vs G3516C) |
| Emissions | Later G3516C-based builds are certified for stationary non-emergency use in the US and can meet NOx levels down to 0.5 g/bhp-hr without aftertreatment; lean-burn configurations with customer-supplied aftertreatment reach 0.3-0.5 g/bhp-hr. Emissions certification depends on the specific engine generation and market — verify against the nameplate/serial prefix for the unit in hand. |
Weights
| Packaged module weight | No single factory weight is published under the PMG3516 module designation itself. Dry weight of the underlying genset package runs roughly in the 12,600-14,200 kg (27,800-31,200 lb) class, and varies by engine generation, enclosure, and rating — confirm against the specific power module's data plate. |
| Ground pressure | Not applicable — stationary/skid or containerized power module, not a tracked or wheeled traction machine |
Dimensions
| Transport length | Roughly 4.2-5.6 m (165-219 in), varies by engine generation and enclosure/skid configuration |
| Transport width | Roughly 1.8-2.2 m (72-85 in), varies by configuration |
| Transport height | Roughly 2.3-2.4 m (92-95 in), varies by configuration |
| Note on dimensions | No dimensions are published specifically under the PMG3516 name; figures above come from the underlying gas genset packages the module is built around and should be confirmed against the unit's own data plate/GA drawing before shipping or siting. |
Performance
| Travel speed | Not applicable — stationary power module (skid or container-mounted), not self-propelled |
| Gradeability / drawbar / dig / lift | Not applicable to this machine type |
| Governed speed | Engine speed set at 1200, 1500, or 1800 rpm depending on the rating sheet applied to the specific unit |
Service capacities (summary)
| Fuel supply | Not applicable in the traditional onboard-tank sense — the engine runs on field/pipeline natural gas supplied to the unit, sized for gas with a heating value of roughly 31.5 to 47.2 MJ/Nm3 at a fuel control valve inlet pressure of about 10.2 to 34.5 kPa. No diesel fuel tank is fitted. |
| Engine oil (lube system refill) | About 424 L (112 gal) on G3516/G3516B-based builds; oil change interval commonly 1000 hours (LE ratings) or up to 1500 hours on lower-duty ratings |
| Cooling system | Jacket-water and aftercooler (SCAC) circuits with engine-driven pumps and thermostats; specific system capacity in liters is not documented in available public spec sheets for this module — verify with the cooling package supplier or dealer |
| Hydraulic system | Not applicable — no hydraulic propulsion or work-tool circuit on this power module |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
PMG3516 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (lube oil system, refill with filter change) | approx. 401-405 L (106-107 US gal), consistent across the 3516/3516B/3516C engine family used in this power-module line | Cat DEO (Diesel Engine Oil) meeting Cat ECF-3, API CI-4; SAE 15W-40 for standard/warm ambient service, SAE 10W-30 grade for colder starting-temperature climates per Cat's multi-viscosity guidance |
| Cooling system (engine jacket-water circuit) | engine-only circuit approx. 233-235 L (61.5-62 US gal); full radiator-cooled system on trailer/skid power-module packages approx. 330 L (87 US gal) - varies by configuration/series (radiator-cooled vs remote heat exchanger vs offshore module cooling, which runs substantially higher) | Cat ELC (Extended Life Coolant) is the current factory fill/top-up recommendation; Cat DEAC (conventional heavy-duty antifreeze/coolant) is the alternate conventional coolant referenced in the maintenance schedule for older service intervals |
| Fuel tank | not a fixed OMM figure - varies by configuration/installation; this is a power-module set typically paired with a separate sub-base or bulk site fuel tank sized by the installer rather than a single engine-fixed capacity | ultra-low sulfur No. 2 diesel fuel meeting Cat's fuel specification; fuel system requires no separate additive beyond approved diesel fuel conditioners in cold climates |
| Generator-end bearing (SR4/SR4B generator, single spherical-roller bearing) | grease-lubricated bearing, no fill-volume capacity - periodic re-greasing per service interval, not a fluid fill | Cat Ball Bearing Grease or equivalent NLGI 2 multipurpose grease |
| Grease points - linkages and governor/actuator fittings | spec only, no fill capacity listed | Cat Multipurpose Grease (MPGM), NLGI 2, general-purpose lithium-complex type |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar PMG3516 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 8,000 h |
|
Servicing the PMG3516 beyond the schedule
Predictive Maintenance & Fluid/Oil Analysis
Run S.O.S oil sampling at every service interval to trend low-ash oil condition, wear metals, and coolant intrusion before they show up in the ignition system or main bearings. Pair oil trending with jacket-water coolant samples, Level 1 at routine intervals and Level 2 at extended service, to catch liner or head corrosion early. Track spark-plug electrode wear and detonation-sensor retard activity between changes; rising retard counts on the ADEM ignition system usually flag fuel-quality drift (methane number) before a misfire or knock event forces an unplanned shutdown.
Corrective & Common Repairs
Ignition-system faults are the most frequent unplanned call on a PMG3516: fouled or worn spark plugs, cracked ignition transformers, and chafed high-tension leads. Air/fuel ratio control drift, sticking wastegates on turbocharged variants, and prechamber carbon buildup follow close behind. On the generator end, watch for winding insulation degradation from condensation in enclosed skids and slip-ring or brush wear on brush-type ends. Confirm engine arrangement, base 3516, 3516B, or 3516C, before sourcing ignition or ECM components; they are not interchangeable across the three control-system generations.
Overhaul & Rebuild Points
Track valve-stem projection wear against the factory take-up limit to schedule cylinder-head and top-end work before it forces an unplanned teardown; the top-end overhaul interval shortens as rated engine speed rises. Bottom-end/major overhaul addresses liners, pistons, and main/rod bearings on a longer cycle tied to load factor and gas quality, with sour or wet field gas shortening both. Budget for generator-end rewind or bearing replacement as a separate line item, since rotor and stator life does not track engine overhaul hours on this module.
Seasonal & Environment Servicing
Sour, wet, or low-methane-number field gas accelerates ignition and valve wear on a PMG3516, so re-tune air/fuel ratio control and inspect prechambers more often when running on marginal wellhead gas. In cold climates, confirm jacket-water heater operation and coolant freeze-point protection before shutdown season. In humid or coastal enclosures, check generator winding insulation resistance more frequently to catch moisture ingress. Dusty sites need shortened air-filter and turbocharger-inspection cycles to protect the air/fuel ratio control system from abrasive buildup.
PMG3516 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1D-4540 | Bolt,Machine Fuel Filter Mounting | Fuel system service | Check fitment → |
| 154-9385 | Filter Element-Fuel | Fuel system service | Check fitment → |
| 5D-5957 | Seal-O-Ring | Fuel system service | Check fitment → |
| 6V-3907 | Seal-O-Ring | Fuel system service | Check fitment → |
| 128-1112 | Filter Element-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
PMG3516 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| CID 100-01 | Low engine oil pressure | Oil level low, worn oil pump, plugged filter, or oil pressure sensor giving a false low reading | Check oil level and filter condition first, confirm with a mechanical gauge before condemning the sensor |
| CID 110-00 | High engine coolant temperature | Low coolant level, restricted radiator/heat exchanger, failed thermostat, or overload condition | Check coolant level and flow, inspect cooling package for restriction, verify thermostat operation |
| CID 190-00 | Engine overspeed | Governor/actuator fault, load rejection, or fuel/air control system malfunction letting speed run away | Verify governor and actuator linkage, check for load-rejection event in the event log, inspect speed control wiring |
| CID 190-08 | Engine speed signal abnormal (loss or erratic RPM signal) | Damaged or misadjusted magnetic pickup, loose connector, or wiring fault to the speed sensor | Check sensor air gap and connector, inspect harness for damage, reseat or replace the speed sensor |
| CID 320-02 | Speed/timing sensor fault | Faulty or misadjusted timing sensor, damaged wiring, or loss of the ignition timing reference signal | Inspect sensor gap and mounting, check harness continuity, replace sensor if signal remains erratic |
| CID 318/319-02 | Right/left bank detonation (knock) sensor signal abnormal | Failed knock sensor, damaged wiring, or actual detonation from lean air/fuel mixture or incorrect timing | Check sensor wiring and mounting torque, verify air/fuel ratio and ignition timing before replacing the sensor |
| CID 301-xx | Ignition transformer primary circuit fault (per-cylinder) | Failed ignition transformer, spark plug, or open/shorted primary wiring on the affected cylinder | Isolate the cylinder from the code number, inspect transformer and plug, check primary harness for continuity |
| CID 91-08 | Throttle position signal abnormal | Faulty throttle position sensor, linkage binding, or wiring fault causing an invalid signal to the control module | Check throttle linkage for free movement, inspect sensor connector and wiring, recalibrate or replace sensor |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
PMG3516 attachments & work tools
Generator-end / alternator
The PMG designation identifies a permanent-magnet-generator excited alternator end fitted to the 3516 platform genset, giving stable voltage under nonlinear or motor-starting loads without relying on a shunt-excited residual-magnetism system. It shares the same SR-series brushless alternator family used across other Cat 3500 generator sets, sized to the engine's continuous/standby rating.
Enclosure / mounting
Documented examples of this power module are built as open or canopied skid-mounted packages rather than walk-in housings, matching the general Cat 3500 oilfield/power-module practice of pairing engine, generator, radiator, and base on a common skid. Sound-attenuated and weatherproof enclosure options exist across the wider 3516 genset line, but no source ties a specific enclosure code to the PMG3516 by name.
Control panel / switchgear
Parts and service literature for 3516-family generator sets of this era reference EMCP-series control panels (EMCP 3 and EMCP 4.1/4.2/4.3 variants), providing engine and generator monitoring, protective shutdowns, and local start/stop control. Where units are paralleled or tied to switchgear, Cat's standard and custom switchgear/paralleling control packages apply at the site level rather than as a panel built into the module itself.
Cooling arrangement
Cooling is radiator-based and skid-mounted with the engine and generator, consistent with other 3500-platform power modules; no remote or keel-cooled variant specific to the PMG3516 is documented.
Notable factory configuration
The PMG3516 surfaces in parts catalogs as an engine-generator set on the 3516 platform, and the related 3516B HD power module line was marketed for prime power on SCR-driven drilling rigs (onshore and offshore), suggesting an oilfield/drilling duty niche for this family. This industry link is inferred from the shared 3516 power-module lineage, not from a document naming the PMG3516 directly.
All PMG3516 assemblies by section
Every catalogued assembly group for the Caterpillar PMG3516. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
184-1418 Aftercooler Gp-Treated Water
| 11***67 | Rod-Zinc | 2 |
| 13***96 | Washer; (10.2x39.6x2.3-mm Thk) | 4 |
| 15***51 | Gasket | 2 |
184-1419 Aftercooler Gp-Water
| 06***86 | Connector | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 16 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 4 |
188-9078 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 6 |
| 18***78 | Air Cleaner Group | 1 |
8n-3378 Air Cleaner Gp
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
| 2K***73 | Locknut Inside Guard Assembly | 4 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 2 |
134-3805 Arrestor Gp-Flame
| 13***05 | Arrestor Group-Flame | 1 |
| 13***06 | Arrestor As-Flame | 1 |
| 15***55 | Gasket-Manifold | 1 |
146-0758 Bypass Gp-Exhaust
| 10***19 | Base As | 1 |
| 11***72 | Diaphragm | 1 |
| 14***51 | Cover As | 1 |
165-4406 Bypass Gp-Exhaust
| 14***58 | Bypass Group-Exhaust | 1 |
| 16***06 | Bypass Group-Exhaust | 1 |
| 16***00 | Locknut; (High Temperature) | 4 |
217-4418 Drain Gp-Muffler
| 00***43 | Elbow | 1 |
| 02***34 | Coupling | 2 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 2 |
7w-1678 Indicator Gp-Air Filter Change
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 4W***20 | Indicator-Air Filter Change | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
188-6294 Lines Gp-Air -Plenum
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 48 |
| 13***04 | Elbow | 15 |
| 15***41 | Adapter | 1 |
159-9759 Lines Gp-Air -Turbocharger, Aftercooler
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 12***36 | Flange | 1 |
264-3746 Lines Gp-Air -Bypass
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 13***41 | Joint As | 4 |
| 14***62 | Fitting-Pipe | 1 |
157-5154 Manifold Gp-Exhaust
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0V***75 | Screw,Cap,Hexagon H Shaft Mtg,Accessory Drive | 2 |
| 11***14 | Washer; (10.3x18.3x2.66-mm Thk) | 240 |
227-4489 Muffler Gp
| 14***96 | Insulation As | 1 |
| 15***69 | Insulation As | 2 |
| 21***54 | Adapter As | 1 |
214-7176 Muffler Gp
| 14***96 | Insulation As | 1 |
| 15***69 | Insulation As | 2 |
| 21***54 | Adapter As | 1 |
201-1292 Shield Gp-Exhaust
| 1C***69 | Bolt (1/2 In. Long 5/16 In. Dia.); Support Assembly To Heater Group | 2 |
| 20***92 | Shield Group-Exhaust | 1 |
| 22***39 | Spring | 4 |
188-4605 Turbocharger Gp
| 12***36 | Gasket; (Turbocharger) | 2 |
| 16***10 | Coupling | 2 |
| 16***00 | Locknut; (High Temperature) | 8 |
289-1450 Turbocharger Gp
| 12***75 | Bolt; (3/8x16x1.75-In)(Compressor) | 8 |
| 12***76 | Plate-Clamp; (Compressor) | 4 |
| 17***95 | Cover-Compressor | 1 |
188-6295 Turbocharger Gp
| 12***75 | Bolt; (3/8x16x1.75-In)(Compressor) | 8 |
| 12***76 | Plate-Clamp; (Compressor) | 4 |
| 17***95 | Cover-Compressor | 1 |
Basic Engine
4p-8352 Camshaft Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 4N***50 | Dowel; (1.25in X .376in) | 2 |
153-0395 Coupling Gp-Generator
| 15***95 | Coupling Group-Generator | 1 |
| 5N***93 | Plate Group-Generator Coupling | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
6i-1392 Cover Gp-Accessory Drive -Upper, Rh
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 10 |
| 23***46 | Seal-O-Ring | 1 |
| 25***98 | Seal-O-Ring | 1 |
224-3389 Cover Gp-Cylinder Block -Central Structure
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 15***57 | Cover-Camshaft | 2 |
158-7644 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 15***57 | Cover-Camshaft | 2 |
4p-8309 Cover Gp-Flywheel Housing -Rear Structure
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
4p-8304 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 24 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 23***46 | Seal-O-Ring | 1 |
2w-5616 Cover Gp-Oil Pan
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***64 | Cover As | 1 |
| 2W***16 | Cover Group-Oil Pan | 1 |
4p-8310 Cover Gp-Valve Mechanism
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 27***57 | Seal; (Valve Cover To Breather) | 1 |
| 4P***10 | Cover Group-Valve Mechanism | 1 |
8n-0337 Crankshaft Gp
| 12***45 | Bolt As; (5/8-18x4.25-In)(Counterweight) | 48 |
| 12***88 | Crankshaft As | 1 |
| 14***31 | Bearing As-Main; (Standard) | 9 |
350-1417 Cylinder Block As
| 21***26 | Liner-Cylinder Block | 16 |
| 22***96 | Cap-Crankshaft Bearing | 9 |
| 33***50 | Seal-Liner | 16 |
106-2780 Cylinder Block As
| 10***80 | Cylinder Block As | 1 |
| 22***96 | Cap-Crankshaft Bearing | 9 |
| 4W***13 | Plug; (2-1/4-12 Thd) | 4 |
350-1393 Cylinder Block As
| 22***96 | Cap-Crankshaft Bearing | 9 |
| 35***93 | Cylinder Block As | 1 |
| 4W***13 | Plug; (2-1/4-12 Thd) | 4 |
101-1173 Cylinder Block As
| 10***73 | Cylinder Block As | 1 |
| 21***26 | Liner-Cylinder Block | 16 |
| 22***96 | Cap-Crankshaft Bearing | 9 |
115-5159 Cylinder Block Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 2 |
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 16 |
| 10***73 | Cylinder Block As | 1 |
353-3971 Cylinder Block Gp
| 21***68 | Seal-O-Ring; (11.89-mm Id) | 6 |
| 2W***40 | Plug-Oil Manifold | 8 |
| 35***93 | Cylinder Block As | 1 |
115-5160 Cylinder Block Gp
| 03***42 | Seal-O-Ring; (11.89mm Id) | 6 |
| 10***80 | Cylinder Block As | 1 |
| 11***60 | Cylinder Block Group | 1 |
128-1141 Cylinder Head As
| 12***63 | Insert-Valve Seat | 2 |
| 12***41 | Cylinder Head As | 1 |
| 18***94 | Guide-Valve; (Exhaust)(Standard) | 2 |
212-0939 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 13***20 | Fastener Group-Cylinder Head | 6 |
| 13***21 | Fastener Group-Cylinder Head | 2 |
206-1561 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 2 |
| 19***66 | Guide-Valve; (Inlet)(Standard) | 2 |
| 19***99 | Rotocoil As | 4 |
128-1142 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 4 |
| 12***41 | Cylinder Head As | 1 |
| 12***42 | Cylinder Head Group | 1 |
201-7250 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 12***12 | Seal-Water; (11.2mm Id) | 4 |
| 12***13 | Seal-Water; (21.2mm Id) | 4 |
206-1560 Cylinder Head Gp
| 19***60 | Insert-Valve Seat; (Exhaust)(Standard) | 2 |
| 20***46 | Insert-Valve Seat; (Exhaust 0.254-mm Os Od) | 0 |
| 20***47 | Insert-Valve Seat; (Exhaust 0.508-mm Os Od) | 0 |
8n-7182 Damper Gp
| 19***88 | Damper As | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 10 |
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
202-8640 Drain Gp-Engine Oil -Rear
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 20***40 | Drain Group-Engine Oil; -Rear | 1 |
| 3B***45 | Nipple-Pipe; (3/4-14 Npt Thd)(Both Ends) | 1 |
107-7361 Drive Gp-Accessory -Upper, Rh
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 10***66 | Gear-Accessory Drive; (55-Teeth) | 1 |
7e-7647 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
| 12***00 | Bearing-Sleeve | 1 |
2w-8772 Flywheel Gp
| 23***43 | Gear-Flywheel; (183-Teeth) | 1 |
| 24***19 | Flywheel As | 1 |
| 2W***72 | Flywheel Group | 1 |
8n-7174 Gear Gp-Front -Standard Rotation
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
112-5674 Gear Gp-Rear -Cam Drive
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 10***65 | Plate-Thrust | 1 |
| 10***68 | Washer-Thrust; (19.50 X 106 X 1.9mm Thk) | 2 |
151-9228 Guard Gp-Belt -Alternator
| 15***28 | Guard Group-Belt; -Alternator | 1 |
| 17***59 | Guard As-Belt; (Alternator) | 1 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 1 |
7w-5780 Guard Gp-Belt -Alternator
| 23***89 | Nut-Flange; (1/2-13-Thd) | 2 |
| 28***74 | Guard As-Alternator | 1 |
| 7W***80 | Guard Group-Belt; -Alternator | 1 |
8n-9639 Guard Gp-Damper
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 6 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 8 |
4p-8307 Housing Gp-Flywheel
| 1A***69 | Bolt (R.H. Side Flywheel Housing) | 2 |
| 1D***90 | Bolt 4.75 In.(120.65 mm) Long | 16 |
| 22***19 | Housing-Flywheel | 1 |
7w-3724 Housing Gp-Front -Accessory Drive
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 10***34 | Housing-Accessory Drive | 1 |
| 1D***93 | Bolt 5.5 In. (13.97 cm) Long | 10 |
140-9593 Lifting Gp-Engine
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 14***93 | Lifting Group-Engine | 1 |
| 14***94 | Bracket As | 1 |
7e-4836 Mounting Gp-Alternator
| 05***65 | Sleeve | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 14***16 | Belt-Serpentine; (Alternator) | 1 |
217-2001 Mounting Gp-Engine
| 14***90 | Plate | 1 |
| 14***54 | Plate | 1 |
| 14***68 | Isolator | 1 |
9y-3082 Pan Gp-Oil
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
7c-4711 Pan Gp-Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 18 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 50 |
197-4705 Piston & Rod Gp
| 10***30 | Bearing-Connecting Rod; (Standard) | 1 |
| 10***31 | Bearing-Connecting Rod; (0.63-mm Us Id) | 1 |
| 10***32 | Bearing-Connecting Rod; (1.27-mm Us Id) | 1 |
7w-3813 Seal Gp-Crankshaft
| 11***32 | Seal Group-Crankshaft; (Cw Rotation) | 1 |
| 11***33 | Seal Group-Crankshaft; (Ccw Rotation) | 1 |
| 7W***13 | Seal Group-Crankshaft | 1 |
8n-8510 Valve Gp-Explosion Relief
| 27***59 | Seal | 2 |
| 2W***84 | Kit-Repair; (Explosion Relief)(Crankcase) | 1 |
| 8N***09 | Valve Group-Explosion Relief; (Crankcase) | 2 |
1w-8465 Valve Mechanism Gp
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 12***81 | Bridge As | 2 |
| 13***49 | Base As | 1 |
Cooling System
224-8649 Baffle Gp-Radiator
| 21***35 | Angle | 1 |
| 21***36 | Baffle | 1 |
| 21***37 | Plate | 1 |
190-1328 Baffle Gp-Radiator
| 18***27 | Channel | 2 |
| 19***26 | Baffle As | 1 |
| 19***27 | Baffle As | 1 |
193-1759 Connection Gp-Water -Outlet, Lh
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
9y-8179 Connection Gp-Water -Inlet, Outlet
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
193-9193 Connection Gp-Water -Rh
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
4w-5891 Cooler Gp-Engine Oil
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
| 10***32 | Seal-O-Ring | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
207-6037 Cooling Ar
| 19***28 | Baffle Group-Radiator | 1 |
| 20***16 | Lines Group-Water; -Jacket Water | 1 |
| 20***17 | Lines Group-Water; -Scac | 1 |
217-1993 Cooling Ar
| 18***00 | Mounting Group-Radiator | 1 |
| 19***28 | Baffle Group-Radiator | 1 |
| 20***16 | Lines Group-Water; -Jacket Water | 1 |
206-6773 Housing & Regulator Gp
| 11***74 | Valve As-Vent Line | 1 |
| 15***10 | Seal-Integral; (Water Temperature Regulator) | 1 |
| 20***73 | Housing & Regulator Group | 1 |
7e-4711 Housing & Regulator Gp
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 2 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 2 |
| 4P***05 | Regulator-Water Temperature; (35-Deg C) | 2 |
216-6217 Housing & Regulator Gp -Aftercooler
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 21***28 | Housing | 1 |
| 21***29 | Adapter | 1 |
212-3557 Lines Gp-Vent
| 03***67 | Connector-Flared -- Adapter To Hose As. | 2 |
| 05***00 | Tee Pilot Valve Drain | 1 |
| 11***79 | Hose - 34.5 In. (876 mm) Drum Clutch Release | 1 |
190-0376 Lines Gp-Vent
| 19***76 | Lines Group-Vent | 1 |
| 20***78 | Hose As | 1 |
| 20***80 | Hose As, . Cover | 1 |
202-6716 Lines Gp-Water -Jacket Water
| 14***09 | Bolt; (Self-Tapping) | 12 |
| 18***85 | Tube As | 1 |
| 18***26 | Tube As | 1 |
174-6061 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
9y-9185 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
202-6717 Lines Gp-Water -Scac
| 12***30 | Gasket | 1 |
| 14***09 | Bolt; (Self-Tapping) | 4 |
| 19***38 | Hose As | 2 |
193-4737 Lines Gp-Water
| 00***04 | Fitting-Flared | 2 |
| 00***81 | Tee-Union; (Flared 37-Deg) | 1 |
| 00***25 | Elbow-Flared | 1 |
200-6977 Lines Gp-Water
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
189-9100 Mounting Gp-Radiator
| 18***00 | Mounting Group-Radiator | 1 |
| 18***01 | Isolator | 4 |
| 3B***10 | Lockwasher Use With Customer'S Grounding Bolt | 4 |
219-0265 Mounting Gp-Radiator
| 18***01 | Isolator | 5 |
| 21***65 | Mounting Group-Radiator | 1 |
| 7X***50 | Bolt (5/8 X 11 X 3.50 In.) | 4 |
212-8166 Pump Gp-Auxiliary Water
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***66 | Pump Group-Auxiliary Water | 1 |
291-4311 Pump Gp-Auxiliary Water -Fresh Water
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***79 | Shaft; (14-Teeth) | 1 |
9y-8175 Pump Gp-Auxiliary Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 7 |
| 1T***65 | Bolt 2.54 cm (1" Long) | 1 |
| 21***66 | Pump Group-Auxiliary Water | 1 |
7e-9782 Pump Gp-Auxiliary Water
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 12***00 | Bearing-Sleeve | 1 |
166-4378 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
212-8177 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
2w-9729 Pump Gp-Water
| 16***78 | Pump Group-Water; -Jacket Water | 1 |
| 1H***78 | Seal-O-Ring | 1 |
| 2W***29 | Pump Group-Water; Water Pump Group | 1 |
208-0273 Radiator Gp
| 12***69 | Hose-Hydraulic; (199-In) | 0 |
| 12***28 | Bearing | 2 |
| 12***46 | Sheave | 1 |
208-3648 Radiator Gp
| 12***79 | Hose-Hydraulic; (915-cm) | 0 |
| 12***28 | Bearing | 2 |
| 12***46 | Sheave | 1 |
270-4025 Regulator Gp-Temperature
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 8 |
7e-3783 Regulator Gp-Temperature -Aftercooler
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 2 |
| 1A***37 | Bolt Clutch Assembly To Bracket (Fan Support) | 2 |
Electrical And Starting System
3n-8278 Adapter-Sensor
| 3N***78 | Adapter-Sensor; Adapter--1/2" Pipe Thread | 1 |
266-7227 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
112-3455 Alternator Gp-Charging
| 09***19 | Washer; (7.14x15.88x1.58-mm Thk) | 2 |
| 11***55 | Alternator Group-Charging | 1 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
4n-3986 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
| 10***62 | Kit-Alternator Terminal | 1 |
331-5717 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
206-1236 Battery Gp
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 14***09 | Bolt; (Self-Tapping) | 8 |
| 15***53 | Cable-Electrical; (00-Ga, Red)(411-cm) | 0 |
6i-3164 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
122-1194 Box & Mounting Gp -Cable Access
| 12***94 | Box & Mounting Group; -Cable Access | 1 |
| 12***33 | Frame As-Box | 1 |
| 12***35 | Cover-Top | 1 |
357-3040 Box & Mounting Gp -Cable Access
| 10***46 | Fastener | 4 |
| 12***35 | Cover-Top | 1 |
| 12***36 | Cover-Bottom | 1 |
224-8647 Box As-Junction
| 15***23 | Hinge As | 2 |
| 22***47 | Box As-Junction | 1 |
| 33***85 | Latch As | 2 |
236-8214 Box Gp-Control
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***61 | Cap-Dust | 1 |
| 10***35 | Plug As-Connector; (37-Pin) | 1 |
115-2513 Box Gp-Extension Terminal -Circuit Breaker
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 10 |
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***34 | Cover As-Top | 1 |
264-0589 Box Gp-Generator Connection
| 14***09 | Box Group-Generator Connection | 1 |
| 26***89 | Box Group-Generator Connection | 1 |
357-3045 Box Gp-Generator Connection
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 18 |
141-1809 Box Gp-Generator Connection
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 18 |
102-6843 Box Gp-Terminal
| 10***43 | Box Group-Terminal | 1 |
| 15***21 | Box | 1 |
| 15***60 | Plate; (Stainless Steel) | 1 |
164-5699 Box Gp-Terminal
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***59 | Receptacle | 1 |
| 10***61 | Cap-Dust | 1 |
158-3516 Box Gp-Terminal
| 15***16 | Box Group-Terminal | 1 |
| 16***98 | Bracket As | 1 |
| 16***99 | Box Group-Terminal | 1 |
252-7458 Bus Bar As
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 6 |
| 20***43 | Bolt; (M12x1.75x42.5-mm) | 12 |
| 25***58 | Bus Bar As | 1 |
122-0332 Cable Gp -Circuit Breaker Connection
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 24 |
| 12***32 | Cable Group; -Circuit Breaker Connection | 1 |
252-7537 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***31 | Circuit Breaker Group | 1 |
252-7538 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***32 | Circuit Breaker Group | 1 |
252-7534 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***30 | Circuit Breaker Group | 1 |
252-7539 Circuit Breaker & Mounting Gp
| 10***97 | Bar-Circuit Breaker; (3200-Ampere) | 2 |
| 10***16 | Bar-Circuit Breaker; (3200-Ampere) | 3 |
| 10***18 | Bar-Circuit Breaker; (3200-Ampere) | 1 |
105-7935 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***35 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
105-7934 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
252-7531 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***31 | Circuit Breaker Group | 1 |
| 27***59 | Circuit-Breaker; (2000-Ampere) | 1 |
220-7973 Circuit Breaker Gp
| 22***73 | Circuit Breaker Group | 1 |
| 22***85 | Control-Electronic; (Circuit Breaker Trip) | 1 |
| 22***86 | Coil; (Shunt Trip) | 1 |
105-7929 Circuit Breaker Gp
| 10***29 | Circuit Breaker Group | 1 |
| 10***35 | Circuit Breaker As | 1 |
| 10***97 | Bar-Circuit Breaker; (3200-Ampere) | 1 |
252-7532 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***32 | Circuit Breaker Group | 1 |
| 27***60 | Circuit Breaker As; (2500-Ampere) | 1 |
106-5664 Circuit Breaker Gp
| 10***35 | Circuit Breaker Group; (1200-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***64 | Circuit Breaker Group | 1 |
221-8599 Circuit Breaker Gp
| 22***85 | Control-Electronic; (Circuit Breaker Trip) | 1 |
| 22***86 | Coil; (Shunt Trip) | 1 |
| 22***87 | Motor-Electric; (Circuit Breaker) | 1 |
114-4674 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 11***74 | Circuit Breaker Group | 1 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 9 |
105-7927 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 10***32 | Switch As-Auxiliary | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
252-7533 Circuit Breaker Gp
| 25***57 | Bus As; (3200-Ampere) | 2 |
| 25***29 | Circuit Breaker As; (3200-Ampere) | 1 |
| 25***33 | Circuit Breaker Group | 1 |
105-7928 Circuit Breaker Gp
| 10***28 | Circuit Breaker Group | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***99 | Bar-Circuit Breaker | 3 |
252-7530 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***30 | Circuit Breaker Group | 1 |
| 27***58 | Circuit-Breaker; (1600-Ampere) | 1 |
208-0387 Conduit Gp-Electrical
| 11***14 | End-Wire; (18-Ga) | 15 |
| 11***97 | End-Wire; (14-Ga) | 30 |
| 11***61 | End-Wire; (10-Ga) | 20 |
209-8419 Conduit Gp-Electrical
| 19***26 | Clamp; (Conduit) | 6 |
| 20***16 | Elbow; (1/2-14 Npt) | 1 |
| 20***18 | Connector; (1/2 X 14 Npt) | 6 |
209-9170 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 12 |
| 15***05 | Body; (Unilet) | 2 |
| 15***91 | Channel; (426-cm) | 0 |
209-9377 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 24 |
| 15***05 | Body; (Unilet) | 4 |
| 15***91 | Channel; (426-cm) | 0 |
209-8272 Conduit Gp-Electrical
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 6 |
| 19***26 | Clamp; (Conduit) | 6 |
| 20***18 | Connector; (1/2 X 14 Npt) | 10 |
211-4369 Conduit Gp-Electrical
| 10***43 | Box Group-Terminal | 1 |
| 15***86 | Insert-Nut | 6 |
| 15***91 | Channel; (426-cm) | 0 |
202-7903 Conduit Gp-Electrical
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 3 |
| 14***09 | Bolt; (Self-Tapping) | 6 |
| 15***86 | Insert-Nut | 36 |
209-8174 Conduit Gp-Electrical
| 19***26 | Clamp; (Conduit) | 2 |
| 20***18 | Connector; (1/2 X 14 Npt) | 4 |
| 20***25 | Connector; (Tee 1/2-14 Npt) | 2 |
209-9678 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 2 |
| 15***91 | Channel; (426-cm) | 0 |
| 19***26 | Clamp; (Conduit) | 1 |
249-0655 Conduit Gp-Electrical
| 10***38 | End-Wire; (16-Ga) | 10 |
| 11***14 | End-Wire; (18-Ga) | 10 |
| 11***97 | End-Wire; (14-Ga) | 10 |
217-0044 Conduit Gp-Electrical
| 20***18 | Connector; (1/2 X 14 Npt) | 2 |
| 20***01 | Conduit; (857-cm) | 0 |
| 21***44 | Conduit Group-Electrical | 1 |
209-9351 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 18 |
| 15***05 | Body; (Unilet) | 3 |
| 15***91 | Channel; (426-cm) | 0 |
215-6424 Conduit Gp-Electrical
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 3 |
| 14***09 | Bolt; (Self-Tapping) | 6 |
| 15***86 | Insert-Nut | 42 |
221-3930 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 10 |
| 15***91 | Channel; (426-cm) | 0 |
| 19***26 | Clamp; (Conduit) | 8 |
211-4370 Conduit Gp-Electrical
| 10***43 | Box Group-Terminal | 1 |
| 15***86 | Insert-Nut | 6 |
| 15***91 | Channel; (426-cm) | 0 |
121-9640 Connection Gp-Electrical -Rtd
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
264-0587 Connection Gp-Electrical -Rtd
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 26***87 | Connection Group-Electrical; -Rtd | 1 |
278-7734 Connection Gp-Electrical
| 23***24 | Contactor | 1 |
| 25***13 | Strip Group-Terminal | 1 |
| 27***34 | Connection Group-Electrical | 1 |
257-9401 Connection Gp-Electrical
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 22***53 | Relay; (24-Volt)(Space Heater) | 1 |
| 22***54 | Socket-Relay | 1 |
213-8045 Connection Gp-Electrical
| 17***99 | Strip Group-Terminal; -Dc | 1 |
| 21***41 | Strip Group-Terminal | 1 |
| 21***42 | Strip Group-Terminal; -Ac | 1 |
121-9638 Connection Gp-Electrical -Basic
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 17***00 | Strip Group-Terminal; -Main | 1 |
| 4F***57 | Screw,Cap,Hexagon H Shock Mount To Bracket | 2 |
264-1456 Connection Gp-Electrical
| 21***45 | Connection Group-Electrical | 1 |
| 26***56 | Connection Group-Electrical | 1 |
249-4057 Connection Gp-Electrical
| 24***57 | Connection Group-Electrical | 1 |
| 3L***36 | Spacer-Bracket To Diesel Water Passage Cover | 1 |
| 3L***04 | Shield-Terminal | 1 |
212-0221 Connection Gp-Electrical
| 21***21 | Connection Group-Electrical | 1 |
| 21***22 | Strip Group-Terminal | 1 |
| 4F***57 | Screw,Cap,Hexagon H Shock Mount To Bracket | 2 |
218-4826 Connection Gp-Electrical -Terminal Block, Rtd
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
| 20***44 | Transformer As-Current | 1 |
| 21***26 | Connection Group-Electrical; -Terminal Block, Rtd | 1 |
256-7511 Control Gp-Communication -Pl1000t
| 12***74 | Screw-Pan Head; (8-32x9.52-mm) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 25***11 | Control Group-Communication; -Pl1000t | 1 |
256-7512 Control Gp-Communication -Pl1000e
| 25***12 | Control Group-Communication; -Pl1000e | 1 |
| 33***85 | Film-Warning; (Csa Control Panel Approval) | 1 |
131-7416 Control Gp-Converter
| 13***15 | Harness As-Wiring; (Rs232) | 1 |
| 13***16 | Control Group-Converter | 1 |
5n-0591 Control Gp-Manual Voltage
| 5N***91 | Control Group-Electronic | 1 |
| 5N***03 | Varistor As | 1 |
| 5N***05 | Plate-Switch | 1 |
210-1438 Control Gp-Electronic
| 11***42 | Timer | 1 |
| 12***68 | Circuit Breaker; (15 Amp, 1 Pole) | 2 |
| 12***70 | Circuit Breaker As; (20-Ampere) | 1 |
210-1436 Control Gp-Electronic
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***44 | Seal | 1 |
| 11***45 | Plug As-Connector; (40-Pin) | 1 |
210-3299 Control Gp-Electronic
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***44 | Seal | 1 |
| 11***45 | Plug As-Connector; (40-Pin) | 1 |
154-6713 Control Gp-Engine Electronic
| 15***13 | Control Group-Engine Electronic | 1 |
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 34***92 | Control Group-Engine Electronic | 1 |
193-5762 Control Gp-Ignition
| 15***14 | Ignition Group-Gas Engine | 1 |
| 15***15 | Thermocouple Group | 1 |
| 19***61 | Wiring Group-Engine | 1 |
215-2903 Detector Gp-Methane
| 21***03 | Detector Group-Methane | 1 |
169-1585 Enclosure Gp-Wiring
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 4 |
| 16***82 | Plate | 1 |
| 16***85 | Enclosure Group-Wiring | 1 |
128-1479 Frame Gp-Generator Connection -Generator Connection
| 12***79 | Frame Group-Generator Connection; -Generator Connection | 1 |
| 1D***72 | Bolt-Carriage; (1/2-13x5.5-In) | 6 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 6 |
357-3041 Frame Gp-Generator Connection
| 1D***72 | Bolt-Carriage; (1/2-13x5.5-In) | 6 |
| 23***54 | Fastener | 12 |
| 35***41 | Frame Group-Generator Connection | 1 |
217-0098 Harness As
| 21***98 | Harness As | 1 |
270-1732 Harness As-Control -Pl1000t
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
276-0785 Harness As-Control -Pl1000e
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
158-3531 Harness As-Engine -Gas Shutoff Valve
| 15***31 | Harness As-Engine; -Gas Shutoff Valve | 1 |
212-0227 Harness As-Panel
| 21***27 | Harness As-Panel; -Interface | 1 |
| 8T***37 | Plug-Seal; (40 Pin Connector) | 1 |
| 9X***87 | Plug As-Connecting | 1 |
231-1941 Harness As-Panel -Customer Connection
| 13***59 | Cable-Electrical; (1520-cm) | 0 |
| 23***41 | Harness As-Panel; -Customer Connection | 1 |
| 5P***09 | Tube-Heat Shrink; (9.52-mm Dia)(0.03-M Each) | 0 |
242-9752 Harness As-Power -Digital Voltage Regulator
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Terminal As-Ring | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
194-0503 Harness As-Sensor
| 19***03 | Harness As-Sensor | 1 |
221-3933 Harness As-Sensor
| 11***97 | End-Wire; (14-Ga) | 2 |
| 19***62 | Film-Identification; (Wire)(Label) | 20 |
| 20***99 | Connector-Wire | 6 |
243-4271 Harness As-Wiring -Generator Terminal Strip
| 23***56 | Plug-Connector; (6-Pin) | 1 |
| 23***57 | Plug-Connector; (9-Pin) | 1 |
| 23***58 | Plug-Connector; (12-Pin) | 1 |
240-6833 Harness As-Wiring -Ignition, Lh
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
242-3104 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 22 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
240-6834 Harness As-Wiring -Emcp Ii
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 10 |
| 24***34 | Harness As-Wiring; -Emcp Ii | 1 |
209-7551 Harness As-Wiring -Shunt Trip
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 2 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
242-3100 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 24 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***66 | Wedge-Plug Lock; (3-Pin) | 1 |
7e-6248 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
7e-6247 Heater Gp-Jacket Water
| 10***32 | Thermostat; (60 Deg F To 160 Deg F)(Jacket Water Heater) | 1 |
| 7E***47 | Heater Group-Jacket Water | 1 |
189-6642 Heater Gp-Jacket Water
| 14***85 | Pump; (Circulation) | 1 |
| 18***42 | Heater Group-Jacket Water | 1 |
| 19***79 | Seal | 2 |
200-6504 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 20***04 | Heater Group-Jacket Water | 1 |
158-3514 Ignition Gp-Gas Engine
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 20 |
| 10***83 | Guard As; (Camshaft) | 1 |
320-9980 Installation Gp-Communication
| 25***11 | Control Group-Communication; -Pl1000t | 1 |
| 27***32 | Harness As-Control; -Pl1000t | 1 |
| 32***80 | Installation Group-Communication | 1 |
320-9979 Installation Gp-Communication
| 22***59 | Cable As-Communication | 1 |
| 25***12 | Control Group-Communication; -Pl1000e | 1 |
| 27***85 | Harness As-Control; -Pl1000e | 1 |
9x-1439 Lamp Gp-Flood
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 1 |
| 8T***33 | Nut (M10x1.50 Thd) | 1 |
177-4564 Lighting Gp-Flood
| 15***21 | Box | 1 |
| 17***64 | Lighting Group-Flood | 1 |
| 17***37 | Timer As; (60-Minute) | 1 |
102-8447 Lighting Gp-Generator
| 10***47 | Lighting Group-Generator | 1 |
203-5892 Motor Starter
| 20***92 | Motor Starter; (Radiator Fan Motor) | 1 |
| 20***93 | Contactor | 1 |
| 20***94 | Relay; (Overload) | 1 |
213-0420 Mounting Gp -Switch Gear
| 15***46 | Isolator | 6 |
| 21***20 | Mounting Group; -Switch Gear | 1 |
| 7X***87 | Washer; (10.26x22.22x1.9-mm Thk) | 6 |
122-0319 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***93 | Bracket As-Circuit Breaker; -Circuit Breaker | 1 |
| 12***19 | Mounting Group-Circuit Breaker | 1 |
252-7525 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 25***21 | Support | 2 |
| 25***22 | Panel | 1 |
122-3488 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***88 | Mounting Group-Circuit Breaker | 1 |
| 12***29 | Bracket | 1 |
208-1195 Mounting Gp-Circuit Breaker
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 20***95 | Mounting Group-Circuit Breaker | 1 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 4 |
270-4654 Mounting Gp-Circuit Breaker
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 27***48 | Bracket | 1 |
| 27***54 | Mounting Group-Circuit Breaker | 1 |
217-4415 Mounting Gp-Gas Detector
| 14***27 | Nut; (3/8-16-Thd) | 2 |
| 15***91 | Channel; (426-cm) | 0 |
| 20***60 | Nut As-Spring; (1/4-20-Thd) | 2 |
208-0812 Mounting Gp-Jacket Wtr Heater -Rh
| 03***07 | Connector; (Flared) | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
134-3159 Mounting Gp-Jacket Wtr Heater -Rh
| 00***70 | Nipple-Strainer To Flange | 1 |
| 03***07 | Connector; (Flared) | 1 |
| 03***28 | Clip; (31.8mm Id) | 4 |
134-3160 Mounting Gp-Jacket Wtr Heater -Lh
| 00***70 | Nipple-Strainer To Flange | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
141-1810 Mounting Gp-Transformer
| 14***10 | Mounting Group-Transformer | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 4 |
122-0317 Panel As-Box -Circuit Breaker
| 12***17 | Panel As-Box; -Circuit Breaker | 1 |
| 12***40 | Panel-Circuit Breaker | 1 |
| 7W***91 | Seal (104 cm) | 0 |
252-7535 Panel Gp-Circuit Breaker -Cover
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 12 |
| 25***23 | Panel | 1 |
| 25***35 | Panel Group-Circuit Breaker; -Cover | 1 |
307-9794 Cover-Extension Box
| 30***94 | Plate-Cover, Twelve Point Cap Screw | 1 |
213-4743 Plug Gp-Auxiliary Power
| 20***92 | Receptacle As | 3 |
| 20***06 | Plate | 1 |
| 21***60 | Box As | 1 |
262-5313 Plug Gp-Auxiliary Power
| 21***43 | Plug Group-Auxiliary Power | 1 |
| 26***13 | Plug Group-Auxiliary Power | 1 |
| 5S***49 | Bolt; (1/4-20x0.5-In)(1/4-20x.5in) | 14 |
221-0752 Relay Gp -Space Heater
| 10***38 | End-Wire; (16-Ga) | 4 |
| 12***99 | Harness As-Wiring; (Main Terminal Strip) | 1 |
| 12***97 | Harness As-Wiring; (Dc Terminal Strip) | 1 |
228-9263 Sensor Gp-Humidity
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 2 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 1 |
212-3426 Sensor Gp-Speed
| 21***58 | Tube-Heat Shrink; (24-mm Dia)(200-cm) | 0 |
| 21***26 | Sensor Group-Speed; -Magnetic | 1 |
| 9X***92 | Sensor Group-Speed; -Timing | 1 |
102-9029 Sensor Gp-Speed
| 10***29 | Sensor Group-Speed; -Timing-Engine Speed | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 3 |
| 8L***86 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
4p-7610 Sensor Gp-Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***49 | Strap; (Marker) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
265-9034 Sensor Gp-Speed
| 11***66 | Seal-O-Ring | 1 |
| 13***07 | Washer; (21.1x28.1x0.9-mm Thk) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
9x-5392 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
6i-4907 Sensor Gp-Temperature -Generator Bearing
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
| 11***47 | Cover | 1 |
175-5341 Sensor Gp-Temperature
| 17***41 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
141-4159 Sensor Gp-Temperature -Generator Bearing
| 14***59 | Sensor Group-Temperature; -Generator Bearing | 1 |
130-9811 Sensor Gp-Temperature -Engine Oil
| 13***11 | Sensor Group-Temperature; (Transmission Lubrication Oil) | 1 |
| 13***45 | Pad; (Connector) | 1 |
6i-4906 Sensor Gp-Temperature -Generator Bearing
| 11***22 | Sender As-Temperature; (100-Ohm)(Generator Bearing) | 1 |
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
241-9591 Sensor Gp-Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 24***91 | Sensor Group-Temperature | 1 |
124-8475 Sensor Gp-Temperature -Generator Bearing
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
| 11***47 | Cover | 1 |
141-4158 Sensor Gp-Temperature -Generator Bearing
| 14***58 | Sensor Group-Temperature; -Generator Bearing | 1 |
180-5420 Sensor Gp-Temperature
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 18***20 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
6v-0890 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
6v-0927 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
237-1962 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 13 |
8n-3896 Starting Motor Gp-Electric -Dual
| 3L***36 | Spacer-Bracket To Diesel Water Passage Cover | 1 |
| 3L***04 | Shield-Terminal | 4 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
170-5399 Strip Gp-Terminal -Dc
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***06 | Bar | 1 |
| 17***99 | Strip Group-Terminal; -Dc | 1 |
170-5396 Strip Gp-Terminal -Rtd
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
| 31***98 | Block-Terminal; (600-Volt, 25-Ampere) | 34 |
212-0222 Strip Gp-Terminal
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 21***22 | Strip Group-Terminal | 1 |
| 21***23 | Film-Identification; (Terminal Marker) | 1 |
258-8713 Strip Gp-Terminal
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 17***55 | Marker-Terminal | 1 |
213-8041 Strip Gp-Terminal
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 4 |
213-8042 Strip Gp-Terminal -Ac
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 2 |
170-5400 Strip Gp-Terminal -Main
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 15***55 | Fuse; (10-Ampere) | 2 |
| 17***00 | Strip Group-Terminal; -Main | 1 |
176-1057 Support Gp-Battery
| 17***57 | Support Group-Battery | 1 |
| 22***24 | Support As | 1 |
| 22***25 | Plate-Tread | 1 |
169-5384 Switch Gp-Remote -Starting
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 4 |
| 16***84 | Switch Group-Remote; -Starting | 1 |
| 16***85 | Bracket-Switch | 1 |
3n-5979 Switch-Rotary
| 3N***79 | Switch-Rotary | 1 |
158-3515 Thermocouple Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 12***94 | Wire As-Ground | 1 |
264-1068 Transformer As
| 14***64 | Transformer Group-Current | 1 |
| 26***68 | Transformer As | 1 |
204-3544 Transformer As-Current
| 20***44 | Transformer As-Current | 1 |
122-6586 Transformer As-Current
| 12***86 | Transformer As-Current | 1 |
122-6588 Transformer As-Current
| 12***88 | Transformer As-Current | 1 |
122-6585 Transformer As-Current
| 12***85 | Transformer As-Current | 1 |
117-9724 Transformer As-Current
| 11***24 | Transformer As-Current | 1 |
137-0259 Transformer As-Current
| 13***59 | Transformer As-Current | 1 |
128-0115 Transformer As-Current
| 12***15 | Transformer As-Current | 1 |
117-9722 Transformer As-Current
| 11***22 | Transformer As-Current | 1 |
117-9723 Transformer As-Current
| 11***23 | Transformer As-Current | 1 |
122-6587 Transformer As-Current
| 12***87 | Transformer As-Current | 1 |
122-6590 Transformer As-Current
| 12***90 | Transformer As-Current; (3000:5 Ratio)(3000:5) | 1 |
117-9721 Transformer As-Current
| 11***21 | Transformer As-Current | 1 |
119-0976 Transformer As-Current
| 11***76 | Transformer As-Current | 1 |
119-0977 Transformer As-Current
| 11***77 | Transformer As-Current | 1 |
122-6589 Transformer As-Current
| 12***89 | Transformer As-Current | 1 |
128-0116 Transformer As-Current
| 12***16 | Transformer As-Current | 1 |
122-6591 Transformer As-Current
| 12***91 | Transformer As-Current | 1 |
128-0795 Transformer As-Current
| 12***95 | Transformer As-Current | 1 |
327-9373 Transformer Gp
| 23***50 | Transformer Group-Ignition | 1 |
| 31***62 | Spring | 1 |
| 32***73 | Transformer Group | 1 |
264-1066 Transformer Gp-Current
| 14***60 | Transformer Group-Current; -Droop | 1 |
| 26***66 | Transformer Group-Current | 1 |
144-9064 Transformer Gp-Current
| 11***22 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***64 | Transformer Group-Current | 1 |
144-9060 Transformer Gp-Current
| 12***90 | Transformer As-Current; (3000:5 Ratio)(3000:5) | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***60 | Transformer Group-Current; -Droop | 1 |
144-9061 Transformer Gp-Current
| 12***91 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***61 | Transformer Group-Current | 1 |
144-9066 Transformer Gp-Current
| 11***77 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***66 | Transformer Group-Current | 1 |
229-5837 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***85 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
229-5838 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***86 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
144-9058 Transformer Gp-Current
| 12***88 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***58 | Transformer Group-Current | 1 |
144-9059 Transformer Gp-Current
| 12***89 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***59 | Transformer Group-Current | 1 |
232-6350 Transformer Gp-Ignition
| 12***38 | Spring-Transformer | 1 |
| 13***51 | Seal; (Pressure Relief) | 1 |
| 16***90 | Terminal As | 1 |
178-7193 Transformer Gp-Potential
| 15***71 | Shelf; (Transformer) | 1 |
| 17***93 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 3 |
154-3477 Transformer Gp-Potential
| 15***71 | Shelf; (Transformer) | 1 |
| 15***77 | Transformer Group-Potential | 1 |
| 15***88 | Transformer As; (Low Voltage) | 2 |
125-9326 Transformer Gp-Potential
| 12***26 | Transformer Group-Potential | 1 |
154-3478 Transformer Gp-Potential
| 15***71 | Shelf; (Transformer) | 1 |
| 15***78 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 2 |
264-1455 Transformer Gp-Potential
| 15***77 | Transformer Group-Potential | 1 |
| 26***55 | Transformer Group-Potential | 1 |
119-0978 Transformer-Current
| 11***78 | Transformer-Current; (Ratio 800:5) | 1 |
269-5223 Transformer-Current
| 26***23 | Transformer-Current | 1 |
103-0692 Valve Gp-Solenoid
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 7X***78 | Coil As | 1 |
9y-6992 Valve Gp-Solenoid
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 4P***77 | Gasket | 1 |
| 9X***06 | Receptacle As | 1 |
220-0586 Wiring Gp-Alternator
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 13***24 | Circuit Breaker As; (30-Ampere) | 1 |
| 21***31 | Harness As-Wiring; (Alternator) | 1 |
219-9756 Wiring Gp-Alternator
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 21***31 | Harness As-Wiring; (Alternator) | 1 |
| 21***56 | Wiring Group-Alternator | 1 |
169-1584 Wiring Gp-Electric Starting
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 11***64 | Connector | 1 |
| 16***10 | Harness As-Wiring; (Electric Start) | 1 |
145-5138 Wiring Gp-Electronic Control
| 12***30 | Harness As-Power; -Digital Voltage Regulator | 1 |
| 14***38 | Wiring Group-Electronic Control | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 5 |
168-2029 Wiring Gp-Engine
| 16***28 | Harness As-Wiring; (Jumper) | 1 |
| 16***29 | Wiring Group-Engine | 1 |
216-9609 Wiring Gp-Engine
| 11***61 | End-Wire; (10-Ga) | 3 |
| 20***91 | Wire-Electrical | 0 |
| 20***95 | Wire-Electrical | 0 |
215-6849 Wiring Gp-Engine
| 21***49 | Wiring Group-Engine | 1 |
| 2K***73 | Locknut Inside Guard Assembly | 3 |
| 5M***62 | Bolt; (3/8-16x0.75-In) | 3 |
216-9610 Wiring Gp-Engine
| 11***61 | End-Wire; (10-Ga) | 2 |
| 20***99 | Connector-Wire | 7 |
| 20***00 | Cap | 7 |
166-4155 Wiring Gp-Engine
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 16***55 | Wiring Group-Engine | 1 |
| 16***84 | Wiring Group-Electric Starting | 1 |
209-7811 Wiring Gp-Engine
| 11***61 | End-Wire; (10-Ga) | 11 |
| 16***27 | Ferrule-Wire; (14-Ga) | 13 |
| 19***62 | Film-Identification; (Wire)(Label) | 56 |
193-5761 Wiring Gp-Engine
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 7 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 14 |
216-9025 Wiring Gp-Engine
| 21***25 | Wiring Group-Engine | 1 |
| 2K***73 | Locknut Inside Guard Assembly | 3 |
| 5M***62 | Bolt; (3/8-16x0.75-In) | 3 |
242-7960 Wiring Gp-Generator
| 24***00 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***60 | Wiring Group-Generator | 1 |
241-3379 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 10 |
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 24***68 | Harness As-Wiring; (Voltage Adjustment) | 1 |
264-1461 Wiring Gp-Generator
| 24***60 | Wiring Group-Generator | 1 |
| 26***61 | Wiring Group-Generator | 1 |
242-7961 Wiring Gp-Generator
| 24***04 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***61 | Wiring Group-Generator | 1 |
| 24***52 | Harness As-Power; -Digital Voltage Regulator | 1 |
166-8368 Wiring Gp-Generator
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 32 |
| 10***39 | End-Wire; (12-Ga) | 8 |
243-4285 Wiring Gp-Generator
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 24***71 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***85 | Wiring Group-Generator | 1 |
241-3378 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 3 |
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
261-7168 Wiring Gp-Generator
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 4 |
| 26***67 | Harness As-Wiring; (Shunt Trip) | 1 |
243-4269 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 9 |
| 24***69 | Wiring Group-Generator | 1 |
| 24***01 | Harness As-Wiring; (Vr6 Voltage Regulator) | 1 |
122-0320 Wiring Gp-Generator -Shunt Trip
| 12***20 | Wiring Group-Generator; -Shunt Trip | 1 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
| 7K***81 | Strap-Pressure & Return Hoses To | 10 |
209-8234 Wiring Gp-Machine -Lighting
| 20***76 | Wire-Electrical | 0 |
| 20***34 | Wiring Group-Machine; -Lighting | 1 |
| 5P***29 | Wire (No. 14 Gauge) 3.05 M(10ft.) | 0 |
Enclosures, Guards And Bases
217-2344 Base As
| 21***44 | Base As | 1 |
221-0813 Chassis Gp
| 22***13 | Chassis Group | 1 |
219-3406 Container As
| 11***19 | Plate As | 8 |
| 14***31 | Channel | 10 |
| 14***90 | Screw-Wood | 160 |
225-7903 Container As
| 11***19 | Plate As | 8 |
| 13***18 | Support-Ladder | 2 |
| 14***31 | Channel | 10 |
223-1721 Container As
| 13***18 | Support-Ladder | 2 |
| 14***90 | Screw-Wood | 160 |
| 14***27 | Nut; (3/8-16-Thd) | 22 |
225-7900 Container As
| 13***18 | Support-Ladder | 2 |
| 14***31 | Channel | 10 |
| 14***90 | Screw-Wood | 159 |
219-3408 Container Gp
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 21***07 | Container Group | 1 |
| 21***08 | Container Group | 1 |
217-4599 Container Gp
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 21***61 | Container Group | 1 |
| 21***99 | Container Group | 1 |
214-1660 Container Gp
| 11***19 | Plate As | 8 |
| 13***98 | Floorplate-Galvanized | 9 |
| 14***90 | Screw-Wood | 118 |
219-3407 Container Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
217-6608 Container Gp
| 13***25 | Holder | 2 |
| 21***07 | Container Group | 1 |
| 21***08 | Container Group | 1 |
217-6606 Container Gp
| 11***19 | Plate As | 8 |
| 13***98 | Floorplate-Galvanized | 18 |
| 14***90 | Screw-Wood | 118 |
217-6607 Container Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
223-1723 Container Gp
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 21***43 | Plug Group-Auxiliary Power | 1 |
| 22***22 | Container Group | 1 |
223-1722 Container Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
214-1661 Container Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
219-8028 Containment Gp-Fluid
| 14***09 | Bolt; (Self-Tapping) | 16 |
| 21***57 | Plate | 1 |
| 21***28 | Containment Group-Fluid | 1 |
226-3522 Cover Gp-Access
| 14***09 | Bolt; (Self-Tapping) | 8 |
| 22***20 | Cover As | 1 |
| 22***22 | Cover Group-Access | 1 |
131-0539 Cover Gp-Generator -Coupling
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 12***99 | Bracket-Mounting | 2 |
| 13***38 | Cover-Drip | 1 |
141-4987 Cover Gp-Generator -Coupling
| 12***94 | Cover-Drip | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 1D***40 | Bolt,Machine Fuel Filter Mounting | 6 |
156-9152 Door As
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 6 |
| 15***25 | Rod Group-Access Door | 1 |
| 15***78 | Hinge | 3 |
151-6381 Door As
| 15***81 | Door As | 1 |
| 15***80 | Handle | 1 |
| 16***96 | Nut; (1/4-20-Thd)(Self-Clinching) | 10 |
216-1644 Door As
| 03***60 | Rivets | 47 |
| 15***80 | Handle | 1 |
| 16***96 | Nut; (1/4-20-Thd)(Self-Clinching) | 5 |
169-3185 Door As
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 6 |
| 15***25 | Rod Group-Access Door | 1 |
| 15***78 | Hinge | 3 |
171-4917 Door Gp-Access -Air Vent
| 16***60 | Door Group; (Vent) | 1 |
| 17***37 | Gasket | 1 |
| 17***17 | Door Group-Access; -Air Vent | 1 |
204-5718 Door Gp-Access -Enclosure
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 10 |
| 15***52 | Door As | 1 |
| 15***68 | Angle | 1 |
217-8072 Door Gp-Access
| 15***80 | Handle | 1 |
| 16***96 | Nut; (1/4-20-Thd)(Self-Clinching) | 10 |
| 16***97 | Stud; (1/4-20x0.75-In) | 4 |
113-1204 Door Gp-Access -Switchgear Door
| 11***04 | Door Group-Access; -Switchgear Door-Switchgear Room | 1 |
| 14***27 | Handle-Door | 1 |
| 15***22 | Handle | 1 |
217-8071 Door Gp-Access
| 15***80 | Handle | 1 |
| 16***96 | Nut; (1/4-20-Thd)(Self-Clinching) | 10 |
| 16***97 | Stud; (1/4-20x0.75-In) | 4 |
215-6851 Duct Gp-Cable
| 14***00 | Bellow-Cable | 1 |
| 14***04 | Flange-Bellow | 2 |
| 14***06 | Panel; (Side)(Bottom) | 1 |
217-9328 Duct Gp-Cable
| 14***00 | Bellow-Cable | 2 |
| 14***79 | Insulator-Cable | 1 |
| 15***86 | Insert-Nut | 34 |
212-7108 Enclosure As
| 12***12 | Door-Holdback | 2 |
| 12***14 | Handle-T | 2 |
| 21***08 | Enclosure As | 1 |
212-7109 Enclosure As
| 12***12 | Door-Holdback | 2 |
| 12***14 | Handle-T | 2 |
| 21***09 | Enclosure As | 1 |
225-7902 Enclosure Gp-Generator
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 22***01 | Enclosure Group-Generator | 1 |
| 22***02 | Enclosure Group-Generator | 1 |
225-7905 Enclosure Gp-Generator
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 22***04 | Enclosure Group-Generator | 1 |
| 22***05 | Enclosure Group-Generator | 1 |
225-7901 Enclosure Gp-Generator
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
225-7904 Enclosure Gp-Generator
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 24 |
| 03***60 | Rivets | 28 |
| 15***52 | Door As | 3 |
151-8106 Fan Gp-Circulating
| 11***27 | Fan As | 1 |
| 15***20 | Frame As | 1 |
| 15***23 | Control | 1 |
203-0218 Latch Gp-Access Door -Enclosure
| 20***18 | Latch Group-Access Door; -Enclosure | 1 |
| 26***02 | Bracket-Latch | 3 |
| 26***03 | Latch | 2 |
189-8562 Louver As
| 18***62 | Louver As | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 30 |
| 6C***77 | Rivet-Pop | 371 |
215-7535 Louver As
| 15***08 | Bearing | 10 |
| 21***41 | Flange | 2 |
| 21***42 | Flange | 2 |
216-3513 Louver As
| 15***08 | Bearing | 16 |
| 21***44 | Link As | 1 |
| 21***45 | Link | 8 |
187-9758 Louver As
| 18***58 | Louver As | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 42 |
| 6C***77 | Rivet-Pop | 357 |
216-4994 Louver Gp
| 21***13 | Louver As | 1 |
| 21***94 | Louver Group | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 18 |
189-6425 Louver Gp
| 18***25 | Louver Group | 1 |
| 18***62 | Louver As | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 26 |
202-1295 Louver Gp
| 18***58 | Louver As | 1 |
| 20***95 | Louver Group | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 18 |
216-4993 Louver Gp
| 21***35 | Louver As | 1 |
| 21***93 | Louver Group | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 26 |
178-6325 Mounting Gp-Vibration Isolator
| 15***46 | Isolator | 4 |
| 17***25 | Mounting Group-Vibration Isolator | 1 |
| 8T***96 | Washer-Hard- Line From Pipe As. To Gear | 4 |
122-4869 Panel As-Enclosure -Extension Box
| 12***69 | Panel As-Enclosure; -Extension Box | 1 |
214-1658 Panel Gp-Sound Suppression
| 18***77 | Nut; (5/16-18 Thd) | 32 |
| 1L***66 | Button (Plug) | 2 |
| 20***77 | Guard As | 1 |
216-8950 Panel Gp-Sound Suppression
| 20***34 | Angle | 1 |
| 21***97 | Screw; (5/16-18x2.5-In) | 5 |
| 21***58 | Panel Group-Sound Suppression | 1 |
224-8650 Panel Gp-Sound Suppression
| 18***27 | Channel | 2 |
| 19***27 | Baffle As | 1 |
| 22***49 | Baffle Group-Radiator | 1 |
151-5625 Rod Gp-Access Door
| 15***25 | Rod Group-Access Door | 1 |
| 15***36 | Rod | 1 |
| 16***95 | Bracket | 1 |
155-7444 Shield As
| 15***44 | Shield As | 1 |
| 2D***35 | Locknut (Visor To Bracket) | 8 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 8 |
202-3199 Shield Gp
| 15***44 | Shield As | 1 |
| 20***99 | Shield Group | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 8 |
Engine Arrangement
209-7391 Engine Ar
| 11***74 | Gear Group-Rear; -Cam Drive | 1 |
| 11***59 | Cylinder Block Group | 1 |
| 12***32 | Lines Group-Turbocharger Oil | 1 |
195-2865 General Ar
| 19***65 | General Ar | 1 |
| 20***91 | Engine Ar | 1 |
Fuel System
211-8175 Actuator Gp-Electronic
| 21***75 | Actuator Group-Electronic | 1 |
| 21***76 | Actuator Group-Electronic | 1 |
196-9529 Actuator Gp-Electronic
| 19***28 | Actuator Group-Electronic | 1 |
| 19***29 | Actuator Group-Electronic | 1 |
211-8176 Actuator Gp-Electronic
| 03***32 | Seal-O-Ring | 2 |
| 10***28 | Solenoid As; (Governor Actuator) | 1 |
| 12***74 | Bolt-Socket Head; (M4x0.7x60-mm) | 4 |
196-9528 Actuator Gp-Electronic
| 03***32 | Seal-O-Ring | 2 |
| 10***28 | Solenoid As; (Governor Actuator) | 1 |
| 12***74 | Bolt-Socket Head; (M4x0.7x60-mm) | 4 |
202-4869 Control As-Governor -Load Share
| 20***69 | Control As-Governor; -Load Share | 1 |
264-3742 Lines Gp-Fuel
| 18***58 | Gasket | 2 |
| 1A***60 | Capscrew, Hex Head (1/2 - 13 X 2 G5); (Hex Head) (1/2-13x2 Gd 8 Z) | 8 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 8 |
188-9084 Lines Gp-Fuel
| 18***58 | Gasket | 2 |
| 18***84 | Lines Group-Fuel | 1 |
| 19***78 | Tube As | 2 |
216-8583 Lines Gp-Gas
| 12***37 | Clip-Loop | 1 |
| 14***09 | Bolt; (Self-Tapping) | 8 |
| 14***70 | Gasket | 4 |
208-1798 Lines Gp-Gas
| 12***37 | Clip-Loop | 1 |
| 14***09 | Bolt; (Self-Tapping) | 8 |
| 14***70 | Gasket | 4 |
207-8856 Lines Gp-Gas
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 14***07 | Elbow | 2 |
| 15***93 | Clamp-Hose | 1 |
207-8821 Support Gp-Filter
| 16***61 | Screw; (5/16x1.25-In) | 4 |
| 20***49 | Bracket As | 1 |
| 20***21 | Support Group-Filter | 1 |
151-8677 Throttle Gp
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 6 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 14***41 | Rod | 1 |
175-3140 Throttle Gp
| 15***69 | Body-Throttle | 1 |
| 15***70 | Seal-O-Ring | 1 |
| 15***73 | Plate-Throttle | 1 |
151-0428 Throttle Gp
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 15***28 | Throttle Group | 1 |
191-1820 Valve & Mtg Gp-Fuel
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 8 |
| 18***10 | Valve Group-Fuel | 1 |
| 18***58 | Gasket | 1 |
185-5310 Valve Gp-Fuel
| 18***10 | Valve Group-Fuel | 1 |
| 20***02 | Washer-Hard; (4.45x9.52x1-mm Thk) | 22 |
| 24***20 | Seal | 1 |
Generators
235-2277 Adapter -Lower
| 23***77 | Adapter; -Lower | 1 |
235-2276 Adapter -Upper
| 23***76 | Adapter; -Upper | 1 |
121-5423 Air Filter Gp-Generator
| 12***23 | Air Filter Group-Generator | 1 |
| 12***10 | Frame As-Filter | 1 |
| 12***12 | Filter Element-Air; (Generator) | 1 |
121-5422 Air Filter Gp-Generator
| 12***22 | Air Filter Group-Generator | 1 |
| 12***11 | Frame As-Air Filter | 1 |
| 12***13 | Filter Element-Air; (Generator) | 1 |
152-5179 Bracket Gp-Mounting -Opposite Drive End
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 12***74 | Seal | 1 |
| 13***54 | Bar-Support | 1 |
236-2490 Cable Gp-Generator Ground -Neutral
| 23***54 | Cable; (Grounding) | 1 |
| 23***90 | Cable Group-Generator Ground; -Neutral | 1 |
215-6848 Connection Gp-Generator Leads
| 14***75 | Hood | 1 |
| 20***42 | Terminal-Cable; (17-mm) | 32 |
| 20***13 | Cable; (Black)(360-Dm) | 0 |
217-9341 Connection Gp-Generator Leads
| 14***70 | Connector | 1 |
| 14***71 | Connector | 1 |
| 14***75 | Hood | 1 |
116-9827 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
122-0330 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 15 |
| 12***30 | Connection Group-Terminal Strip | 1 |
122-0328 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 9 |
| 12***28 | Connection Group-Terminal Strip | 1 |
115-3056 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
154-1901 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 36 |
154-1902 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
122-0331 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 18 |
| 12***31 | Connection Group-Terminal Strip | 1 |
118-9430 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 16 |
| 11***32 | Strip-Terminal | 3 |
122-0329 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 12 |
| 12***29 | Connection Group-Terminal Strip | 1 |
121-9480 Connection Gp-Terminal Strip
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 12***80 | Connection Group-Terminal Strip | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
121-5132 Connection Gp-Terminal Strip
| 12***32 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 12 |
| 5N***85 | Tape-Electrical; (Varnished Cambric) | 1 |
122-3487 Conversion Gp-Generator
| 11***12 | Box Group-Extension Terminal; (Low Voltage) | 1 |
| 12***94 | Box & Mounting Group; -Cable Access | 1 |
| 12***87 | Conversion Group-Generator | 1 |
130-8306 Cover-Drip
| 13***06 | Cover-Drip | 1 |
142-4457 Exciter Gp -Power
| 12***26 | Stator-Exciter | 1 |
| 14***57 | Exciter Group; -Power | 1 |
| 1F***42 | Bolt Cover To Shut-Off Housing | 4 |
215-2401 Exciter Gp -Power
| 1F***42 | Bolt Cover To Shut-Off Housing | 4 |
| 20***24 | Rotor-Exciter | 1 |
| 21***01 | Exciter Group; -Power | 1 |
215-2402 Exciter Gp -Power
| 20***24 | Rotor-Exciter | 1 |
| 21***02 | Exciter Group; -Power | 1 |
| 21***04 | Stator-Exciter | 1 |
142-4453 Exciter Gp -Permanent Magnet
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 10***49 | Rotor As-Magnetic | 1 |
| 11***17 | Ring; (Support) | 1 |
144-1820 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***52 | Film; (Information)(Generator) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
264-5021 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***52 | Film; (Information)(Generator) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
164-4946 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***52 | Film; (Information)(Generator) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
141-2018 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 14***17 | Generator Group | 1 |
| 14***18 | Generator Ar | 1 |
144-2080 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***79 | Generator Group | 1 |
264-5024 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
144-1992 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 14***91 | Generator Group | 1 |
| 14***92 | Generator Ar | 1 |
226-1216 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***52 | Film; (Information)(Generator) | 1 |
| 17***19 | Kit-Parts; -Generator | 1 |
147-9494 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***52 | Film; (Information)(Generator) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
147-9493 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***59 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-2079 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***59 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1819 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***59 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
276-4653 Generator Gp
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 14***53 | Exciter Group; -Permanent Magnet | 1 |
| 14***01 | Screen Group-Air | 1 |
226-1215 Generator Gp
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 14***53 | Exciter Group; -Permanent Magnet | 1 |
| 14***01 | Screen Group-Air | 1 |
144-1991 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***59 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
164-4945 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 14***53 | Exciter Group; -Permanent Magnet | 1 |
276-4652 Generator Gp
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 14***52 | Rectifier Group-Revolving | 1 |
| 14***53 | Exciter Group; -Permanent Magnet | 1 |
141-2017 Generator Gp
| 14***17 | Generator Group | 1 |
125-2114 Heat Sink As
| 11***22 | Rectifier; (Positive) | 1 |
| 11***24 | Rectifier; (Negative) | 1 |
| 11***56 | Washer; (5.6x7.8x0.5-mm Thk) | 4 |
102-6826 Heater As-Space
| 10***26 | Heater As-Space, Carrier | 1 |
264-1449 Installation Ar-Generator
| 15***91 | Installation Ar-Generator | 1 |
| 26***49 | Installation Ar-Generator | 1 |
153-0191 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 6 |
| 15***91 | Installation Ar-Generator | 1 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 4 |
242-3487 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 24***87 | Mounting Group-Voltage Regulator | 1 |
| 24***64 | Spacer; (8.5x12.7x94.3-mm Thk) | 3 |
243-4270 Mounting Gp-Voltage Regulator
| 24***70 | Mounting Group-Voltage Regulator | 1 |
| 4L***25 | Lockwasher | 4 |
| 7X***01 | Bolt-Plt; (1/4unc X 1 1/4) | 4 |
123-8591 Mounting Gp-Voltage Regulator
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 24***26 | Washer-Hard; (7.2x32x1-mm Thk) | 6 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 1 |
124-1563 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
5n-0593 Plate Gp-Generator Coupling
| 5N***93 | Plate Group-Generator Coupling | 1 |
| 5N***78 | Plate As | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
298-3817 Rectifier Gp-Revolving
| 11***72 | Harness As-Wiring; (Rectifier) | 1 |
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 29***48 | Heat Sink As | 1 |
142-4452 Rectifier Gp-Revolving
| 11***72 | Harness As-Wiring; (Rectifier) | 1 |
| 12***14 | Heat Sink As | 1 |
| 14***52 | Rectifier Group-Revolving | 1 |
155-3820 Regulator As-Voltage
| 15***20 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3835 Regulator As-Voltage -Digital
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
202-8634 Regulator As-Voltage -Digital
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
259-4020 Regulator As-Voltage
| 25***19 | Film-Identification; (Voltage Regulator)(24-Volt Dc) | 1 |
| 25***20 | Regulator As-Voltage | 1 |
309-1019 Regulator As-Voltage
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
155-3832 Regulator As-Voltage -Digital
| 15***32 | Regulator As-Voltage; -Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
235-5725 Regulator As-Voltage -Digital
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 23***25 | Regulator As-Voltage; -Digital-Generator | 1 |
314-7755 Regulator As-Voltage -Digital
| 24***58 | Film-Warning; (Shock, Electrocution Hazard)(Shock, Electrocution Hazard) | 1 |
| 31***55 | Regulator As-Voltage; -Generator | 1 |
105-4401 Regulator As-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
121-6202 Regulator Gp-Voltage -Digital
| 12***02 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
121-6201 Regulator Gp-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 12***01 | Regulator Group-Voltage | 1 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
263-8921 Regulator Gp-Voltage
| 12***02 | Regulator Group-Voltage; -Digital | 1 |
| 26***21 | Regulator Group-Voltage | 1 |
121-6200 Regulator Gp-Voltage
| 12***00 | Regulator Group-Voltage | 1 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 15***20 | Regulator As-Voltage | 1 |
121-6203 Regulator Gp-Voltage -Digital
| 12***03 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
208-0388 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 15***32 | Ball Bearing | 1 |
| 20***88 | Rotor Group-Generator | 1 |
208-0396 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 15***32 | Ball Bearing | 1 |
| 20***96 | Rotor Group-Generator | 1 |
208-0389 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 15***32 | Ball Bearing | 1 |
| 20***89 | Rotor Group-Generator | 1 |
167-3841 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 15***32 | Ball Bearing | 1 |
| 16***41 | Rotor Group-Generator | 1 |
145-7462 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 14***62 | Rotor Group-Generator | 1 |
| 15***32 | Ball Bearing | 1 |
145-7464 Rotor Gp-Generator
| 13***01 | Kit-Rotor Lead | 1 |
| 14***64 | Rotor Group-Generator | 1 |
| 15***32 | Ball Bearing | 1 |
145-6001 Screen Gp-Air
| 12***59 | Screen As-Air | 2 |
| 14***01 | Screen Group-Air | 1 |
| 3E***23 | Bolt-Flange Head; (1/4-20x1-In) | 4 |
166-7466 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 26 |
| 12***88 | Heater As-Space; (600-Watt) | 2 |
| 12***56 | Bar; (Heater Mounting) | 4 |
145-7595 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 26 |
| 12***88 | Heater As-Space; (600-Watt) | 2 |
| 12***56 | Bar; (Heater Mounting) | 4 |
145-7590 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 26 |
| 12***88 | Heater As-Space; (600-Watt) | 2 |
| 12***56 | Bar; (Heater Mounting) | 4 |
145-7612 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 26 |
| 12***88 | Heater As-Space; (600-Watt) | 2 |
| 12***56 | Bar; (Heater Mounting) | 4 |
145-7619 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 26 |
| 12***88 | Heater As-Space; (600-Watt) | 2 |
| 12***56 | Bar; (Heater Mounting) | 4 |
Lubrication System
191-0618 Breather Gp -Crankcase
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 15***17 | Elbow As | 2 |
| 15***30 | Breather As; (Engine Oil) | 4 |
7n-1875 Filler Gp-Engine Oil -Cylinder Block
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 2W***52 | Gasket | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
155-4843 Filter Gp-Engine Oil
| 14***91 | Filter-Oil; (Advanced Efficiency) | 1 |
| 15***43 | Filter Group-Engine Oil | 1 |
147-3172 Filter Gp-Engine Oil -Rh
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
193-3941 Filter Gp-Engine Oil -Lh
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 7 |
191-2303 Filter Gp-Fumes Disposal
| 19***01 | Filter Element-Fumes Disposal | 1 |
| 19***02 | Gauge Group-Oil Filter Press Diff | 1 |
| 19***03 | Filter Group-Fumes Disposal | 1 |
254-5305 Filter Gp-Fumes Disposal
| 19***02 | Gauge Group-Oil Filter Press Diff | 1 |
| 19***11 | Blower Group-Fumes Disposal | 1 |
| 25***04 | Filter Element-Fumes Disposal | 1 |
219-7814 Filter Gp-Fumes Disposal
| 19***01 | Filter Element-Fumes Disposal | 1 |
| 19***02 | Gauge Group-Oil Filter Press Diff | 1 |
| 21***14 | Filter Group-Fumes Disposal | 1 |
217-1438 Fumes Disposal Gp
| 21***38 | Fumes Disposal Group | 1 |
| 3P***47 | Clamp | 1 |
| 5P***97 | Clamp Fumes Disposal | 2 |
7e-6342 Gauge Gp-Oil Level (Dipstick)
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 4P***84 | Gauge As-Oil Level (Dipstick) | 1 |
194-1463 Lines Gp-Engine Oil -Lh
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 3 |
188-9086 Lines Gp-Engine Oil -Hydrac Discharge
| 00***86 | Connector-Hose (1/4-18nptf Thd) | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 03***33 | Seal-O-Ring; (12.42mm Id) | 6 |
134-3749 Lines Gp-Engine Oil
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
201-7287 Lines Gp-Engine Oil
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
174-4107 Lines Gp-Prelubrication
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 06***56 | Seal-O-Ring | 2 |
| 11***47 | Valve; (Pilot Operated) | 1 |
121-7732 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
190-5980 Manifold Gp-Engine Oil
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
| 10***34 | Grommet | 2 |
8n-6152 Pump Gp-Engine Oil -2-Section Gear
| 29***87 | Seal-O-Ring | 1 |
| 4P***38 | Pump Group-Engine Oil; -2-Section Gear | 1 |
| 4S***82 | Bolt 7.25 In. (18.42 cm) Long | 3 |
4p-5638 Pump Gp-Engine Oil -2-Section Gear
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 9 |
| 11***49 | Gasket | 1 |
113-4174 Pump Gp-Prelubrication
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
2n-7613 Pump Gp-Prelubrication
| 2N***13 | Pump Group-Prelubrication | 1 |
| 7N***09 | Capacitor | 1 |
| 7N***10 | Motor Assem. | 1 |
219-7412 Pump Gp-Sump
| 1K***37 | Elbow-Pipe | 1 |
| 21***12 | Pump Group-Sump | 1 |
| 22***28 | Bracket | 1 |
5n-6237 Pump Gp-Engine Oil -Manual Lubrication
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 2 |
| 3N***97 | Pin-Tapered | 2 |
| 3N***99 | Gasket Set; (Includes 4 Gaskets) | 1 |
5n-4659 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
216-8347 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
102-6845 Tank Gp-Engine Oil
| 00***44 | Elbow; (45-Deg) | 1 |
| 10***45 | Tank Group-Engine Oil | 1 |
| 11***11 | Hose As | 2 |
222-9116 Tank Gp-Engine Oil
| 00***44 | Elbow; (45-Deg) | 1 |
| 11***11 | Hose As | 2 |
| 13***05 | Valve | 1 |
Marine Transmission
225-7906 Control Gp-Power Train
| 11***40 | Terminal-Double | 2 |
| 11***23 | Dial-Vernier | 2 |
| 12***41 | Lamp-Base | 2 |
Operator Station
178-9030 Box As-Storage
| 17***30 | Box As-Storage | 1 |
| 4S***64 | Rivet; (On Front L.H. Of Seat Support) | 4 |
| 5P***37 | Seal 1.667 M(65.25 In.) | 0 |
236-8213 Box Gp-Control Panel
| 16***98 | Bracket As | 1 |
| 23***13 | Box Group-Control Panel | 1 |
| 23***14 | Box Group-Control | 1 |
130-3349 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
118-0175 Control Gp-Emcp Electronic
| 10***27 | Screw-Pan Head; (10-24x0.25-In) | 8 |
| 11***75 | Control Group-Emcp Electronic | 1 |
| 15***65 | Kit-Connecting Plug; (8-Pin)(Electronic Control Channel) | 1 |
118-2070 Control Gp-Emcp Electronic
| 11***70 | Control Group-Emcp Electronic; -Generator Set Control + | 1 |
| 13***15 | Film-Control Panel; (Generator Set Control +)(Emcpii+) | 1 |
| 13***50 | Control Group-Electronic; (Relay Module)(Generator Set Control +) | 1 |
141-1956 Control Gp-Engine Monitoring
| 14***56 | Control Group-Engine Monitoring | 1 |
| 17***86 | Control Group-Engine Monitoring | 1 |
203-4162 Control Gp-Motor Starter
| 20***46 | Heater As; (106 To 144-Ampere)(Starting Motor) | 1 |
| 20***33 | Circuit Breaker As; (175-Ampere) | 1 |
| 20***62 | Control Group-Motor Starter | 1 |
203-8340 Control Gp-Motor Starter
| 10***02 | Terminal; (Single) | 3 |
| 12***41 | Lamp-Base | 2 |
| 12***43 | Lamp-Lens; (Red) | 2 |
168-6426 Door Gp-Access -Switchgear Room
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 11***04 | Door Group-Access; -Switchgear Door-Switchgear Room | 1 |
| 14***09 | Bolt; (Self-Tapping) | 2 |
121-5421 Filter As-Electronic
| 12***21 | Filter As-Electronic; -Radio Frequency Interference | 1 |
145-7571 Filter Gp-Electronic -Radio Frequency Interference
| 12***21 | Filter As-Electronic; -Radio Frequency Interference | 1 |
| 14***70 | Bar; (Grounding) | 2 |
| 14***71 | Filter Group-Electronic; -Radio Frequency Interference | 1 |
230-4194 Fire Extinguisher Gp
| 15***78 | Bracket As | 1 |
| 23***94 | Fire Extinguisher Group | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 3 |
102-6818 Fire Extinguisher Gp
| 10***18 | Fire Extinguisher Group | 1 |
| 14***90 | Screw-Wood | 3 |
| 15***78 | Bracket As | 1 |
104-4704 Mounting Gp-Control Panel -Emcp Ii
| 10***04 | Mounting Group-Control Panel; -Emcp Ii | 1 |
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
217-4532 Mounting Gp-Control Panel
| 15***46 | Isolator | 7 |
| 21***44 | Base As | 1 |
| 21***32 | Mounting Group-Control Panel | 1 |
262-5314 Padlock Gp
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 5 |
| 26***14 | Padlock Group | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
210-1437 Panel Gp-Control -Relay
| 11***40 | Terminal-Double | 2 |
| 11***23 | Dial-Vernier | 2 |
| 12***41 | Lamp-Base | 2 |
221-2780 Panel Gp-Control -Relay
| 11***40 | Terminal-Double | 2 |
| 11***23 | Dial-Vernier | 2 |
| 12***41 | Lamp-Base | 2 |
220-8269 Panel Gp-Electrical -Circuit Breaker
| 22***69 | Panel Group-Electrical; -Circuit Breaker | 1 |
| 22***29 | Circuit Breaker As; (15-Ampere) | 2 |
| 22***30 | Circuit Breaker As; (30-Ampere) | 5 |
212-4726 Panel Gp-Switchgear
| 21***26 | Panel Group-Switchgear | 1 |
| 21***08 | Enclosure As | 1 |
| 21***14 | Panel Group-Switchgear | 1 |
212-4727 Panel Gp-Switchgear
| 21***27 | Panel Group-Switchgear | 1 |
| 21***09 | Enclosure As | 1 |
| 21***14 | Panel Group-Switchgear | 1 |
212-4728 Panel Gp-Switchgear
| 12***71 | Fuse; (20-Ampere) | 1 |
| 12***14 | Handle-T | 4 |
| 18***65 | Fuse; (30-Ampere) | 2 |
212-7114 Panel Gp-Switchgear
| 11***42 | Timer | 1 |
| 12***68 | Circuit Breaker; (15 Amp, 1 Pole) | 1 |
| 12***70 | Circuit Breaker As; (20-Ampere) | 1 |
213-9898 Switchgear Ar
| 21***36 | Control Group-Electronic | 1 |
| 21***38 | Control Group-Electronic | 1 |
| 21***28 | Panel Group-Switchgear | 1 |
213-9896 Switchgear Ar
| 21***37 | Panel Group-Control; -Relay | 1 |
| 21***99 | Control Group-Electronic | 1 |
| 21***26 | Panel Group-Switchgear | 1 |
213-9897 Switchgear Ar
| 21***37 | Panel Group-Control; -Relay | 1 |
| 21***99 | Control Group-Electronic | 1 |
| 21***27 | Panel Group-Switchgear | 1 |
Prime Package
210-5558 Box Gp-Storage
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 15***86 | Insert-Nut | 4 |
| 17***30 | Box As-Storage | 1 |
224-1196 Ladder Gp
| 22***96 | Ladder Group | 1 |
| 22***97 | Ladder As | 1 |
| 22***99 | Handrail As | 1 |
217-9339 Panel As
| 15***41 | Angle | 12 |
| 15***44 | Channel | 12 |
| 15***45 | Channel | 2 |
225-9379 Panel As
| 15***37 | Panel | 16 |
| 15***38 | Panel; (Sound) | 8 |
| 15***41 | Angle | 12 |
216-1597 Panel As
| 15***37 | Panel | 16 |
| 15***38 | Panel; (Sound) | 8 |
| 15***41 | Angle | 12 |
Service Equipment And Supplies
7e-4300 Chart-Instrument Panel
| 7E***00 | Chart-Instrument Panel | 1 |
6l-4502 Chart-Plate & Film
| 12***60 | Film-Information; (Silver Ultraplate)(Certification)(Ce Mark) | 1 |
| 12***61 | Film-Information; (Laminate) | 1 |
| 14***42 | Film-Warning; (Hot Surface) | 2 |
309-5970 Film Gp
| 20***46 | Film-Information; (Phone, Internet Contact) | 2 |
| 20***47 | Film-Information; (Phone, Internet Contact) | 2 |
| 29***46 | Film-Identification; (Cat) | 1 |
264-5354 Film Gp
| 20***60 | Film Group; -Product Identification | 1 |
| 26***54 | Film Group | 1 |
205-7860 Film Gp -Product Identification
| 20***60 | Film Group; -Product Identification | 1 |
| 23***86 | Plate-Identification; (Machine)(17-Pin) | 1 |
121-9272 Kit-Marine Generator Parts
| 12***72 | Kit-Marine Generator Parts | 1 |
202-8587 Kit-Marine Generator Parts
| 20***87 | Kit-Marine Generator Parts; -Retrofit | 1 |
171-6719 Kit-Parts -Generator
| 17***19 | Kit-Parts; -Generator | 1 |
137-8533 Shim Pack
| 13***33 | Shim Pack; (Includes 13-Shims) | 1 |
| 13***34 | Shim; (0.025-mm Thk) | 1 |
| 13***35 | Shim; (0.0508-mm Thk) | 1 |
PMG3516 serial number reference
On a PMG3516 gas power module the PIN/serial plate sits on the module skid frame rail, usually near the control panel end or bolted to the engine block data plate on the same skid. The plate reads the model code PMG3516 followed by a 3-character letter prefix identifying the build lot/configuration and a sequential unit number, e.g. JKK00123 or GJK1-UP style ranges shown in parts listings.
| Prefix | Identifies | Notes |
|---|---|---|
| JKK | PMG3516 gas power module, engine-side build (piston group, water pump, battery group, generator drive coupling) | Documented on the PMG3516 power module parts manual for engine-side groups. Piston group is listed as a closed range while the generator drive coupling and other engine-side groups run open-ended, consistent with a running change partway through the lot. |
| GJK | PMG3516 gas power module, control and electrical side (electronic control group, control-box enclosure, oil-level regulator) | Documented as its own range across multiple control-side assemblies on the PMG3516 power module parts manual, separate from the JKK engine-side range. |
| XL6 | PMG3516 gas power module, cylinder head assembly | Documented as XL61-UP on the PMG3516 power module cylinder head group listing. Only one listing found tying it to this range — confirm with dealer before relying on it. |
| KAD | PMG3516 gas power module, accessory drive (upper right-hand accessory drive, standard rotation, not usable with mechanical governor) | Documented as KAD1-UP on the PMG3516 power module accessory-drive parts listing. Only one listing found — confirm with dealer before relying on it. |
Frequently asked questions
What engine powers the Cat PMG3516?
A Caterpillar 3516 (G3516) V-16, four-stroke, spark-ignited natural gas engine. The platform spans three generations, base 3516, 3516B, and 3516C, offered in naturally aspirated, turbocharged-aftercooled, and low-emission configurations.
What does a PMG3516 power module weigh?
Skid weight typically runs roughly 9,000 to 22,000 kg (20,000 to 49,000 lb), varying with generator-end size, enclosure, and power rating. Weight varies by configuration and series, so confirm the exact figure against the specific unit's nameplate.
What replaced the PMG3516, or what is the current equivalent?
There is no separate successor model number. Cat's current gas-engine power module and generator-set line continues under the same G3516 family, now offered in NA, TA, low-emission, heavy-duty, and dynamic-gas-blending configurations built around the ADEM A4 engine management system.
What PMG3516 owners discuss
What's the main thing people say is different about running a PMG3516 versus a diesel Cat power module?
It's detonation sensitivity to fuel gas quality. Owners running the 3516 gas engine on wellhead, associated, or gathering gas keep an eye on methane number because BTU content and inert-gas ratio drift as the field changes. Once methane number sags into the mid-50s or lower, the engine needs a deration or a timing pull-back to stay out of detonation, and skids fed straight off a wellhead with no gas conditioning see the widest swings. A gas analyzer and routine sampling at the skid catch this before it shows up as spark knock or a timing-retard event on the panel.
How long do spark plugs and ignition components actually last on these gas engines?
Plug wear is one of the most predictable consumables people budget around. Running continuous duty under load, plug tips erode and gas-side fouling builds well before a major overhaul is due, and the first sign is usually a rough-running cylinder or an uneven exhaust-temperature spread rather than an outright miss. Most operators pull and inspect plugs on a fixed hour interval instead of waiting for a misfire to show up, since chasing a single dead cylinder after the fact costs more downtime than a scheduled swap.
Is valve lash something to worry about more than on a diesel unit?
Yes, several operators running 3516B gas packages hard in compression service say they end up checking intake valve lash closer to every 1000 hours rather than stretching the interval, because valve recession creeps up faster than expected under gas-engine heat and load cycling. Catching lash drift early is a cheap check next to the cost of a dropped valve. If lash is found consistently out of spec sooner than the book predicts, have your dealer verify valve and seat condition before it turns into a bigger repair.
Does this engine need special oil, and how do people decide when to change it?
Yes. It runs a low-ash oil, generally held under roughly 0.6% sulfated ash, and putting a diesel-spec higher-ash oil in a gas engine by mistake is a known way to build deposits on valves and the upper piston area over time. Rather than changing oil purely on the calendar, most operators run a regular oil-sample program and let a trending TBN/TAN crossover decide the actual drain interval. Clean pipeline-quality gas can let drains stretch well past the factory-default hours if the analysis supports it, while dirtier field gas usually shortens them.
The EMCP panel keeps tripping the unit offline - is that usually the engine or something else?
Most people troubleshooting nuisance trips end up finding a wiring or sensor fault rather than an actual engine problem. The panel separates warning events, which just annunciate and let the set keep running, from shutdown events, which stop the engine and need the underlying condition cleared before they'll reset. Loose or corroded connectors at pressure and temperature sensors are the most commonly reported cause of a shutdown event that turns out not to be a real engine fault. Because a shutdown event is by design tied to something the panel considers unsafe to ignore, have your dealer verify the actual sensor or wiring fault before repeatedly resetting and restarting the set.
What about the generator end itself - anything specific to watch after a unit has sat idle?
The generator end is the part people say gets overlooked on a module that sat in standby duty or between contracts. Moisture can get into the stator windings during a long sit and drop insulation resistance, so a megger check on the windings before re-energizing after storage is standard practice, along with confirming any space heaters actually ran while the unit was down. A reading well below the expected minimum for the winding's rated voltage is a stop-and-check situation - have your dealer verify winding condition before putting the set back on line.
What should I check before buying a used PMG3516 power module?
Beyond hours and a walk-around, buyers focus on a documented top-end history (has the head or piston area ever been opened, and for what reason), oil and coolant analysis trend records rather than a single recent sample, and whether the unit ran prime/continuous duty or sat mostly in standby, since that changes how hard the hours were worked. Ask for ignition and detonation-control fault history off the control logs, and get a generator-end insulation resistance reading before committing. A unit with a full analysis and service paper trail is worth more than one with clean-looking hours and no records, and a compression check plus an independent inspection before money changes hands is the standard advice from people who've bought these before.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific PMG3516 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.