Caterpillarengine - generator setpower module
Caterpillar PM3412
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar PM3412 is a stationary diesel power module: a factory-packaged generator set built onto a fabricated steel mounting skid or trailer sub-base for rental, oilfield, and temporary or standby power duty rather than as a self-propelled machine. It is built around the Caterpillar 3412 or later 3412C TA V-12 diesel, a 27 L (1,650 cu in) turbocharged and aftercooled engine, paired with an SR4-family generator end and an EMCP 3 or EMCP 4 control and protection panel depending on build date. Standard package output centers on roughly 600 kW / 750 kVA at 1800 rpm, 60 Hz, 480 V, though the same engine and generator platform has been packaged at other voltages, frequencies, and ratings up to and above 900 kVA on documented configurations. Dry weight of the bare generator-set engine and alternator assembly runs in the 5.4 to 5.9 metric ton range before the mounting skid, fuel sub-base, enclosure, and cooling package are added, and a fully packaged Power Module weighs measurably more once those items are included. Documented production appears to span roughly the 2000s into the 2010s based on the EMCP 3-to-EMCP 4 control panel transition used on this platform, though exact start and end years are not confirmed, and no verified predecessor or successor model has surfaced in Caterpillar's PM power-module lineup for this unit.
Across its production run the PM3412 platform tracked the base 3412 engine's own evolution toward the 3412C's turbocharged-aftercooled arrangement, and the control panel migrated from EMCP 3 to EMCP 4 electronics as Caterpillar updated the generator-set line. Certain serial prefixes read back to the PM3412 Power Module nameplate directly, while other prefixes surface only in attachment listings and are not independently confirmed. Because these units were built for rental fleets and oilfield service rather than retail sale, used PM3412 modules turn up heavily worked and sometimes re-skidded or re-enclosed, so buyers should verify engine arrangement, generator frame, and control panel generation against the actual nameplate rather than assume it matches a given serial prefix. In the parts market the PM3412 remains relevant mainly as a source of common 3412-family engine components and SR4 generator parts that cross over to other 3412 and 3412C based Cat generator sets, making it a practical donor or rebuild candidate even where the complete power module has aged out of frontline rental service.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar PM3412 specifications
Engine
| Engine model | Cat 3412 diesel V12; later production power modules are built on the 3412C engine platform |
| Configuration | Four-stroke-cycle V12, turbocharged and aftercooled (DITA / 3412C variants) |
| Displacement | 27.0 L (1,649 cu in) |
| Generator set power rating | Most documented power-module packages of this type rate 600 kW (750 kVA) at 1800 rpm, 60 Hz, 480V; the broader 3412 / 3412C generator-set family this unit draws from spans roughly 500-800 ekW depending on rating class and series - varies by configuration |
| Emissions certification | Not published for this exact configuration - not documented, verify certification and serial range with your dealer |
Weights
| Operating weight | Not officially published for this exact unit; comparable trailer-mounted power modules built on the same engine and power class run approximately 8,165 kg (18,000 lb) - treat as an approximate range only |
| Shipping weight | Not documented |
| Ground pressure | Not applicable - trailer-mounted containerized unit, not a tracked or wheeled working machine |
Dimensions
| Transport length | Reported approximately 4.3-5.9 m (14-19 ft) depending on container/trailer configuration - not confirmed for a single fixed spec |
| Transport width | Approximately 2.4 m (8 ft), consistent with a standard container/trailer width |
| Transport height | Approximately 2.9-3.9 m (9.5-13 ft) depending on configuration; lower with any removable exhaust/muffler stack taken off |
| Enclosure | Trailer-mounted, sound-attenuated container; some series ship in a 20 ft container, others in a 40 ft container |
| Wheelbase / track gauge / ground clearance | Not published - the unit is a container mounted on a rental trailer chassis, not a self-propelled undercarriage |
Performance
| Rated frequency / voltage / speed | 60 Hz, 480V, 1800 rpm on documented units |
| Standby / prime output | 600 kW / 750 kVA on the most commonly documented package; the wider engine family this unit is built on covers roughly 500-800 ekW standby depending on rating class - varies by configuration |
| Travel speed / drawbar / gradeability | Not applicable - stationary, trailer-towed power module with no self-propulsion |
Service capacities (summary)
| Fuel tank | Onboard tanks around 2,500 L (660 US gal) reported on comparable containerized power modules in this class - not confirmed as a single fixed figure for this exact unit |
| Cooling system | Engine-only refill approximately 58 L (15.3 US gal); total system capacity runs closer to 67.0 L (17.7 US gal) once the external cooling package is included, per the factory generator-set spec sheet for the 3412C engine |
| Engine oil (lube system) | 139.0 L (36.7 US gal) with filter on twin-turbocharged (DITTA/DITT) arrangements; 60.0 L (15.9 US gal) with filter on single-turbocharged (DIT) arrangements, per the factory generator-set spec sheet for the 3412C engine |
| Hydraulic system | Not applicable - no hydraulic system on this generator set |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
PM3412 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 139 L (147 US qt / approx. 36.7 US gal) with filter, for DITTA and DITT (twin-turbocharged, with or without aftercooling) engine arrangements. 60 L (64 US qt / approx. 15.9 US gal) with filter, for DIT (single turbocharged) engine arrangements. Capacity varies by engine arrangement/aspiration; auxiliary oil filter systems require additional oil beyond these figures. | Cat DEO Multigrade (API CH-4/CG-4). Select viscosity grade by expected ambient temperature at start-up and operation: SAE 0W-20 for -40 to 10 deg C (-40 to 50 deg F), 0W-30 for -40 to 30 deg C (-40 to 86 deg F), 0W-40 for -40 to 40 deg C (-40 to 104 deg F), 5W-30 for -30 to 30 deg C (-22 to 86 deg F), 5W-40 for -30 to 50 deg C (-22 to 122 deg F), 10W-30 for -18 to 40 deg C (0 to 104 deg F), 15W-40 for -9.5 to 50 deg C (15 to 122 deg F). Use the highest viscosity grade available that still meets the cold start-up requirement. |
| Cooling system | Engine-only refill approximately 58 L (62 US qt / approx. 15.3 US gal). Total system capacity depends on the external cooling package (radiator, hoses, any heat exchanger) fitted for the specific installation and is not a fixed figure at the base engine level. | Preferred: Cat ELC Extended Life Coolant or a commercial extended-life coolant meeting the Cat EC-1 specification (rated for six years of service). Acceptable: Cat DEAC or a commercial heavy-duty coolant/antifreeze meeting ASTM D4985 or D5345 (one to three years of service depending on product). Mix water and glycol 1:1 for standard duty. In stationary installations that do not need freeze or boil protection, a water and supplemental coolant additive (SCA) mixture at 6 to 8 percent concentration is acceptable in place of antifreeze. |
| Fuel tank | Not fixed at the engine level. Fuel tank size is set by the generator set packager or enclosure builder and varies by installation; no single capacity applies across configurations. | No. 1-D or No. 2-D diesel fuel per ASTM D975; distillate fuels (diesel fuel, furnace fuel, gas oil, kerosene) are preferred over crude or blended fuels for engine life and performance. Use No. 1 diesel or a No. 1/No. 2 blend in cold weather for better cloud point and pour point behavior. |
| Transmission / powertrain compartment | Not applicable. | This is a stationary engine-generator set with no transmission or powertrain compartment. Engine output couples directly to the generator through the flywheel. |
| Final drives | Not applicable. | No final drives are fitted. The package is stationary and has no travel drivetrain. |
| Hydraulic system and tank | Not applicable. | No hydraulic system is fitted on this engine-generator set. Fuel delivery is controlled by a hydramechanical governor or an electronic control acting on the fuel injection pump, not by a hydraulic circuit. |
| Axles / differentials | Not applicable. | Stationary package; no axles or differentials are present. |
| Grease (spec only) | Applied at individual grease fittings only; no bulk grease fill capacity is specified for this engine. | High-speed ball bearing grease at the fan drive bearing fitting, where equipped. Multipurpose grease at the fuel control linkage grease fittings, where equipped. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar PM3412 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 3,000 h |
|
| Every 5,000 h |
|
| Every 12,000 h |
|
Servicing the PM3412 beyond the schedule
Predictive Maintenance & Fluid Analysis
Pull an S·O·S engine oil sample from the sampling valve every 250 hours and track wear-metal trends across the 3412/3412C V12's cylinder packs. Sample coolant at Level 1 quarterly and Level 2 annually to catch SCA depletion or corrosion risk in the shunt-type cooling system. Megohmmeter-test the SR4 generator stator insulation every three months in humid or marine settings. Log EMCP panel oil pressure, coolant temperature, and battery voltage trends to catch drift before a shutdown fault occurs.
Corrective & Common Repairs
Common PM3412 faults trace to fuel injection nozzle tip wear on the V12, showing up as black smoke, misfire, or rough running, and are isolated cylinder by cylinder before nozzle exchange. A stuck or failed water temperature regulator is a frequent overheating cause in this shunt-design cooling system and should be replaced proactively rather than repaired. Watch the exciter's rotating rectifier diodes for open or shorted faults, and use the EMCP fault-code history to target troubleshooting instead of guessing.
Overhaul & Rebuild Points
Overhaul work centers on the V12's individual cylinder packs, main and rod bearings, and the crankshaft vibration damper, all of which should be replaced rather than reused at teardown regardless of apparent condition. Inspect valve lash, valve rotators, and the turbocharger cartridge for bearing contact with the housing. Pull and pressure-test the oil cooler core and aftercooler core rather than reinstalling them unchecked. A before-failure overhaul on this platform typically runs well under the cost of a comparable new engine and alternator exchange.
Seasonal & Environment Servicing
As a skid-mounted stationary unit often left outdoors on a rental site, the PM3412 depends on its jacket water heater and ether starting aid to start reliably below about 16°C (60°F); verify heater output and ether cylinder charge before cold weather sets in. Use No. 1 diesel or a winter blend to avoid fuel waxing in the primary filter/water separator. In humid or coastal deployments, run generator space heaters whenever the set is idle and recheck stator insulation resistance more often than the standard interval.
PM3412 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1R-0749 | Filter-Fuel | Fuel system service | Check fitment → |
| 134-6307 | Filter Element As-Fuel | Fuel system service | Check fitment → |
| 114-5988 | Film | Fuel system service | Check fitment → |
| 1R-1808 | Filter As-Engine Oil | Lubrication service | Check fitment → |
| 9S-8752 | Nut-Full | Scheduled service item | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
PM3412 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| CID 0100 FMI 01 | Engine oil pressure below the normal operating range | Low oil level, worn oil pump, plugged oil filter, or a failing oil pressure sensor | Check oil level and filter condition first, then verify sensor wiring before condemning the pump |
| CID 0100 FMI 04 | Oil pressure sensor circuit reading voltage below normal (short to ground or open circuit) | Damaged sensor wiring, corroded connector, or a failed sensor | Inspect the sensor harness and connector, then check sensor supply voltage before replacing the sensor |
| CID 0110 FMI 00 | Engine coolant temperature above the normal operating range | Low coolant level, blocked radiator core, failed thermostat, or a slipping fan drive | Check coolant level and radiator airflow, confirm thermostat operation before deeper teardown |
| CID 0111 FMI 01 | Engine coolant level below the normal range | External or internal coolant leak, or a low coolant recovery bottle | Inspect hoses, water pump, and radiator for leaks, then top off coolant and monitor for recurrence |
| CID 0190 FMI 00 | Engine speed above the normal operating range (overspeed) | Governor or fuel-rack actuator malfunction, sticking fuel rack, or a load-rejection event | Check the governor actuator linkage and calibration before returning the set to service |
| CID 0190 FMI 08 | Engine speed/timing signal abnormal or erratic frequency | Damaged or misadjusted speed/timing sensor, loose sensor mounting, or a wiring fault at the ECM connector | Inspect and reseat the speed/timing sensor and its ECM connector, check sensor air gap before replacement |
| CID 0253 FMI 02 | Personality module (ECM programming) data incorrect or corrupted | Mismatched or corrupted engine rating/personality module data in the ECM | Verify the correct personality module is installed, then reload ECM programming with the service tool |
| CID 0001 FMI 05 | Cylinder injector solenoid circuit open, shown here for cylinder 1 but representative of the per-cylinder injector CID range used across the V12 | Broken injector wiring, a disconnected injector connector, or a failed injector solenoid | Inspect the injector wiring harness and connector at the valve cover before replacing the injector |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
PM3412 attachments & work tools
Product type note
PM3412 is a Power Module (skid-packaged diesel engine-generator set) built around the 3412/3412C TA engine, not an implement-carrying machine. There are no work-tool or coupler attachments; the entries below cover the factory configuration, control, and packaging options actually offered for this genset class.
Generator end / alternator
Pairs with an SR4-family generator end (self-excited, 3-phase sensing, reconnectable stator with multiple leads, Class F rise on Class H insulation). Output is factory set at 480V three-phase, 60 Hz, 1800 rpm on most documented units, with other reconnections possible through the alternator's lead arrangement.
Control and monitoring package
Offered with an EMCP digital control panel (generation spans EMCP 3 and EMCP 4 depending on build date) providing engine/generator metering, overspeed and failure-to-start protection, and a data link for remote or accessory modules. Paralleling/synchronizing-capable control is a common upgrade path on this class of power module rather than a base-unit standard.
Enclosure / housing options
Available as an open skid-mounted unit or in a weather-protective or sound-attenuated enclosure; attenuated housings on this generator class are quoted at roughly 25 dBA of noise reduction versus open units, though exact levels vary by enclosure package and test standard. Rental/oilfield-oriented builds are sometimes offered containerized (ISO-style) for transport and site protection.
Fuel system configuration
A sub-base (belly) fuel tank integrated under the generator skid is a standard offering for outdoor standby and oilfield power-module packages of this size, sized to give extended run time between refueling; a remote/day-tank arrangement is used instead where the sub-base tank isn't practical.
Cooling arrangement
Standard cooling is a skid-mounted radiator sized for the full load rating; a remote radiator option is offered for high-ambient sites, indoor installs, or where engine-room airflow is restricted, matching the flexible-cooling approach used across this 3412-based genset family.
Air intake and exhaust options
Factory options include single-element, dual-element, or heavy-duty air cleaners depending on site dust conditions, plus a choice of industrial-grade or critical-grade (higher-attenuation) exhaust silencers/mufflers to meet site noise limits.
Cold-weather and starting package
Jacket-water/block heaters and a factory battery and battery-charger set are offered to keep the unit start-ready in standby or seasonal service, consistent with other 3412-family generator set packages.
Mounting / base and paralleling
Base configuration is a fabricated steel skid with a built-in mounting arrangement aligning engine and generator at the factory; trailer-mount or containerized basing is used for rental and oilfield mobile power. Multiple power modules of this size are commonly paralleled through external switchgear for load-sharing on drilling-rig or rental power setups, though the switchgear itself is a separate accessory, not a built-in PM3412 feature.
All PM3412 assemblies by section
Every catalogued assembly group for the Caterpillar PM3412. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
4n-8099 Aftercooler Gp-Water
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 16 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
4n-2905 Air Cleaner Gp
| 0L***95 | Washer .25 In.(6.35 mm)Thick | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 8 |
1w-8636 Air Cleaner Gp
| 1W***36 | Air Cleaner Group | 1 |
| 4D***22 | Plate | 1 |
| 4W***48 | Clamp As (Center) | 6 |
126-3884 Cap As-Rain -Exhaust
| 12***84 | Cap As-Rain; -Exhaust | 1 |
9n-3676 Cartridge Gp-Turbocharger
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 4 |
| 1N***51 | Shroud-Turbine Wheel | 1 |
| 1P***20 | Ring-Seal | 1 |
5l-7520 Elbow-Exhaust
| 5L***20 | Elbow-Exhaust | 1 |
2w-7848 Fitting Gp-Exhaust
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 8 |
| 21***45 | Bellows As | 1 |
| 2W***48 | Fitting Group-Exhaust | 1 |
2n-3322 Gauge Gp-Air Cleaner
| 2N***22 | Gauge Group-Air Cleaner; Air Filter Indicator Group | 1 |
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 1 |
| 5L***33 | Fitting (To Air Cleaner) | 1 |
4w-7649 Lines Gp-Air
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 6 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 4 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
8n-8925 Manifold Gp-Exhaust
| 10***06 | Manifold-Exhaust; (End) | 2 |
| 10***07 | Manifold-Exhaust; (Middle) | 2 |
| 10***12 | Manifold-Exhaust | 2 |
202-0048 Manifold Gp-Exhaust
| 10***06 | Manifold-Exhaust; (End) | 2 |
| 10***07 | Manifold-Exhaust; (Middle) | 2 |
| 10***12 | Manifold-Exhaust | 2 |
148-0759 Muffler
| 14***59 | Muffler | 1 |
172-2436 Muffler Gp
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 28 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***84 | Cap As-Rain; -Exhaust | 1 |
172-2843 Muffler Gp
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 28 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***84 | Cap As-Rain; -Exhaust | 1 |
4w-4890 Shield Gp-Manifold
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
6n-9091 Shield Gp-Heat
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 4 |
| 2W***74 | Bracket | 2 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
169-1918 Sleeve-Exhaust Manifold
| 16***18 | Sleeve-Exhaust Manifold | 1 |
4w-7648 Turbocharger Gp
| 14***68 | Turbocharger Group | 1 |
| 2N***66 | Locknut; (3/8-16-Thd)(High Temperature) | 8 |
| 4W***48 | Turbocharger Group | 1 |
144-4568 Turbocharger Gp
| 13***77 | Cover-Compressor | 1 |
| 14***68 | Turbocharger Group | 1 |
| 1W***33 | Housing-Turbine | 1 |
Basic Engine
4n-0965 Camshaft Gp
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 10***74 | Gear-Camshaft Drive; (86-Teeth) | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
270-1482 Coupling Gp-Generator
| 10***68 | Plate-Coupling | 1 |
| 27***82 | Coupling Group-Generator | 1 |
| 3P***19 | Washer; (23x36.5x2.67-mm Thk) | 8 |
108-1467 Coupling Gp-Generator
| 10***67 | Coupling Group-Generator | 1 |
| 10***68 | Plate-Coupling | 1 |
| 3P***19 | Washer; (23x36.5x2.67-mm Thk) | 8 |
4n-6866 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
| 23***37 | Seal-Integral | 1 |
| 23***71 | Seal-Integral | 1 |
6n-1897 Cover Gp-Flywheel Housing
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
4n-6798 Cover Gp-Front Housing
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
4w-2581 Cover Gp-Valve Mechanism
| 27***83 | Seal-O-Ring | 4 |
| 4W***80 | Base-Valve Mechanism Cover | 4 |
| 4W***81 | Cover Group-Valve Mechanism | 1 |
213-3202 Crankshaft As
| 15***40 | Gear-Crankshaft; (99-Teeth) | 1 |
| 21***02 | Crankshaft As | 1 |
| 4N***84 | Dowel; (.75 Long) | 1 |
4n-0922 Crankshaft Gp
| 14***67 | Seal Group-Crankshaft; (Front) | 1 |
| 14***68 | Seal-Crankshaft; (Rear)(Flywheel Housing) | 1 |
| 15***40 | Gear-Crankshaft; (99-Teeth) | 1 |
117-9512 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 12 |
| 11***12 | Cylinder Block As | 1 |
| 14***17 | Seal-O-Ring; (140.20mm Id) | 12 |
126-1372 Cylinder Block As
| 12***72 | Cylinder Block As | 1 |
| 2W***15 | Insert-Liner Seat; (1.605-mm Thk)(1.59mm Thk) | 0 |
| 3P***23 | Bolt-Bearing Cap; (7/8-14x7.75-In) | 14 |
126-1373 Cylinder Block Gp
| 11***27 | Seal-O-Ring; (19.18mm Id) | 8 |
| 12***72 | Cylinder Block As | 1 |
| 12***73 | Cylinder Block Group | 1 |
4n-1201 Cylinder Block Gp
| 10***23 | Insert-Liner Seat; (5.21-mm Thk)(5.21mm Thk) | 0 |
| 10***24 | . Cover, Insert-Liner Seat; (5.16-mm Thk)(0.5-mm Us) | 0 |
| 10***25 | Insert-Liner Seat; (5.26-mm Thk)(0.5-mm Os), . Cover | 0 |
143-0046 Cylinder Head As
| 14***46 | Cylinder Head As | 1 |
| 1W***83 | Insert-Valve Seat; (Exhaust)(Standard) | 12 |
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 12 |
143-0047 Cylinder Head As
| 14***46 | Cylinder Head As | 1 |
| 14***47 | Cylinder Head As | 1 |
| 17***88 | Guide-Valve; (Standard) | 24 |
4w-7007 Cylinder Head Gp
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 19 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 1 |
141-3228 Cylinder Head Gp
| 12***21 | Valve-Exhaust | 12 |
| 12***22 | Valve-Inlet | 12 |
| 14***28 | Cylinder Head Group | 1 |
7w-2365 Damper & Pulley Gp
| 16***31 | Damper As | 1 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 12 |
| 2D***55 | Stud-Taperlock; (1/2-13x3.58-In) | 12 |
7n-8847 Drive Gp-Fan -Blower
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 4 |
314-5047 Fastener Gp-Coupling
| 31***47 | Fastener Group-Coupling | 1 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 16 |
| 8T***22 | Washer-Hard-To Lock Carrier Rollers | 6 |
2w-0763 Flywheel Gp
| 0S***02 | Bolt; (5/8-18x3.5-In) | 12 |
| 2W***63 | Flywheel Group | 1 |
| 2W***65 | Flywheel As | 1 |
4n-6341 Gear Gp-Front -Timing
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 1 |
| 11***17 | Plate-Thrust | 1 |
7e-9054 Guard Gp-Belt
| 1F***50 | Nut Rops Support | 1 |
| 4K***97 | Nut 7.94 mm.3125 In.) Thread | 3 |
| 4P***81 | Bracket As | 1 |
201-7583 Guard Gp-Belt
| 1F***50 | Nut Rops Support | 1 |
| 1S***36 | Spacer | 1 |
| 20***83 | Guard Group-Belt | 1 |
7e-9052 Guard Gp-Belt
| 1F***50 | Nut Rops Support | 1 |
| 1S***36 | Spacer | 1 |
| 4K***97 | Nut 7.94 mm.3125 In.) Thread | 5 |
4n-2931 Housing Gp-Flywheel
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 2 |
4n-5226 Housing Gp-Front
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 2 |
| 16***45 | Gasket-Cylinder Block | 1 |
201-9883 Lifting Gp-Engine
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 1N***22 | Bracket-Lifting; (L.H.-Rear) | 1 |
| 20***83 | Lifting Group-Engine | 1 |
7n-7767 Lifting Gp-Engine
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 8 |
| 1N***22 | Bracket-Lifting; (L.H.-Rear) | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 8 |
4p-4061 Mounting Gp-Alternator
| 1S***89 | Rod End,Generator C Bracket Uoc:Bsu,Bsw | 1 |
| 2R***94 | Spacer; (0.562x1x1.31-In Thk) | 1 |
| 2W***74 | Bracket | 2 |
201-7370 Mounting Gp-Engine
| 1F***50 | Nut Rops Support | 1 |
| 20***70 | Mounting Group-Engine | 1 |
| 2N***66 | Locknut; (3/8-16-Thd)(High Temperature) | 12 |
172-4707 Mounting Gp-Engine
| 15***52 | Plate As | 4 |
| 17***07 | Mounting Group-Engine | 1 |
| 1D***86 | Bolt (3.50" Long--.625" Dia.) | 4 |
162-8685 Mounting Gp-Engine
| 11***19 | Plate As | 4 |
| 14***90 | Plate | 4 |
| 14***54 | Plate | 4 |
155-1390 Mounting Gp-Engine
| 11***54 | Isolator | 1 |
| 15***90 | Mounting Group-Engine | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 2 |
2w-9208 Pan Gp-Oil -Engine
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 40 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 23***72 | Seal-Integral | 2 |
2w-9054 Piston & Rod Gp
| 13***61 | Ring-Piston; (Top)(Top) | 1 |
| 16***78 | Rod As-Connecting | 1 |
| 2P***17 | Ring-Piston; (Intermediate)(Intermediate) | 1 |
127-3512 Plug Gp-Cylinder Block
| 12***12 | Plug Group-Cylinder Block | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 6 |
| 7W***34 | Plug-Pipe (3/8-18 Nptf Thd) | 4 |
7w-5927 Rocker Arm Gp
| 00***03 | Ring-Retaining | 2 |
| 0L***22 | Plug (.656" Dia.) | 2 |
| 10***03 | Screw; (3/8-24x1.67-In)(Intake) | 6 |
7w-5926 Rocker Arm Gp
| 00***03 | Ring-Retaining | 2 |
| 0L***22 | Plug (.656" Dia.) | 2 |
| 10***03 | Screw; (3/8-24x1.67-In)(Intake) | 6 |
319-7401 Seal Gp-Crankshaft -Front
| 14***67 | Seal Group-Crankshaft; (Front) | 1 |
| 31***01 | Seal Group-Crankshaft; -Front | 1 |
319-0785 Seal Gp-Crankshaft -Rear
| 14***68 | Seal-Crankshaft; (Rear)(Flywheel Housing) | 1 |
| 31***85 | Seal Group-Crankshaft; -Rear | 1 |
2w-9183 Support Gp-Engine -Front
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 8 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 12 |
| 2W***83 | Support Group-Engine; -Front | 1 |
4n-7352 Valve Mechanism Gp
| 10***89 | Bridge-Valve | 24 |
| 10***88 | Valve Lifter Assem | 24 |
| 23***85 | Bolt-12 Point Head; (3/4-16x11.5-In) | 1 |
Cooling System
160-6193 Baffle Gp-Radiator
| 15***26 | Baffle As; (Lh), Gear | 1 |
| 15***27 | Gear, Baffle As; (Rh) | 1 |
| 15***28 | Baffle As; (Top) | 1 |
160-5188 Baffle Gp-Radiator
| 16***85 | Baffle As; (Lh) | 1 |
| 16***86 | Baffle As; (Rh) | 1 |
| 16***87 | Baffle As; (Top) | 1 |
160-6197 Baffle Gp-Radiator
| 15***55 | Baffle As; (Lh) | 1 |
| 15***56 | Baffle As; (Rh) | 1 |
| 15***57 | Baffle As; (Top) | 1 |
4n-2388 Cooler Gp-Engine Oil
| 10***77 | Seal-O-Ring; (100.97mm Id) | 2 |
| 4N***88 | Cooler Group-Engine Oil; Engine Oil Cooler Group | 1 |
| 7C***45 | Core As-Oil Cooler; (Water Lines) | 1 |
230-7171 Drain Gp-Coolant
| 00***03 | Adapter-Pipe | 1 |
| 14***74 | Valve Group-Radiator Drain | 1 |
| 23***71 | Drain Group-Coolant | 1 |
6n-4371 Fan Gp-Blower
| 6N***71 | Fan Group-Blower | 1 |
| 7N***06 | Spider As-Fan; (8-Blade) | 1 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 6 |
7w-2035 Guard As-Radiator
| 7W***35 | Guard As-Radiator | 1 |
210-9064 Lines Gp-Coolant Drain
| 10***45 | Clamp-Hose; (14-21mm Id) | 1 |
| 12***69 | Hose-Hydraulic; (199-In) | 0 |
| 1P***78 | Clamp; (Hose) | 1 |
6n-1898 Lines Gp-Water
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 5 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
6n-4762 Lines Gp-Water -Radiator
| 4P***17 | Tube | 1 |
| 5L***42 | Gasket-Radiator Pipe | 1 |
| 5P***68 | * Hose-Radiator Inlet-16 cm(6.30 In.) | 0 |
6n-4874 Lines Gp-Water
| 5P***62 | (5 Inches) Hose,Preformed Radiator Outlet Elbow | 0 |
| 5P***17 | Clamp-Hose | 2 |
| 5P***68 | Clamp-Hose; (Us Sourced) | 6 |
4n-2452 Lines Gp-Water
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 7 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 10 |
137-1339 Pump Gp-Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***30 | Bearing As-Roller | 1 |
| 11***21 | Plug-Felt; (Water Pump Housing) | 1 |
4n-5837 Pump Gp-Water
| 10***49 | Adapter-Inlet | 1 |
| 11***79 | Seal-O-Ring | 1 |
| 11***80 | Seal-O-Ring | 1 |
7e-9798 Radiator Gp
| 1W***36 | Guard As-Core | 2 |
| 1W***37 | Plate | 1 |
| 2L***56 | Spacer .312 In. (7.93 mm) Thick; (0.344x0.75x0.313-In Thk) | 3 |
7e-9056 Radiator Gp
| 1B***74 | Plug,Pipe Base Assembly,Engine Oil Filter Assembly | 2 |
| 1F***50 | Nut Rops Support | 5 |
| 4M***61 | Bolt-To Assemble Valve As And Plates | 20 |
140-2674 Valve Gp-Radiator Drain
| 14***74 | Valve Group-Radiator Drain | 1 |
| 14***70 | Nipple-Pipe | 1 |
| 14***74 | Coupling-Pipe | 1 |
137-1942 Valve Gp-Radiator Drain
| 13***42 | Valve Group-Radiator Drain | 1 |
| 3B***49 | Fitting; (Nipple) (1-11-1/2 Npt Thd) | 1 |
| 4P***17 | Valve-Ball; (Jacket Water Heater) | 1 |
137-1943 Valve Gp-Radiator Drain
| 11***36 | Valve As-Shutoff; (Jacket Water Heater) | 1 |
| 13***43 | Valve Group-Radiator Drain | 1 |
| 3B***45 | Nipple-Pipe; (3/4-14 Npt Thd)(Both Ends) | 1 |
Electrical And Starting System
7c-2700 Control Gp-Manual Voltage
| 7C***00 | Module-Control | 1 |
105-7185 Harness As-Panel -Circuit Breaker
| 10***85 | Wiring Group; -Circuit Breaker | 1 |
| 10***38 | End-Wire; (16-Ga) | 2 |
| 4B***74 | Washer (Required Only When Bosch Alternator Is Fitted) | 1 |
5n-5692 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 5 |
| 11***19 | Diode As-Alternator | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
131-0831 Battery Charger
| 13***31 | Battery Charger | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
| 13***74 | Fuse; (15-Ampere) | 1 |
131-0829 Battery Charger
| 13***29 | Battery Charger | 1 |
| 13***71 | Fuse; (6-Ampere) | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
131-0830 Battery Charger
| 13***30 | Battery Charger | 1 |
| 13***71 | Fuse; (6-Ampere) | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
131-0832 Battery Charger Gp
| 13***32 | Battery Charger Group | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
| 13***74 | Fuse; (15-Ampere) | 1 |
206-1236 Battery Gp
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 14***09 | Bolt; (Self-Tapping) | 8 |
| 15***53 | Cable-Electrical; (00-Ga, Red)(411-cm) | 0 |
178-3323 Battery Gp
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 15***53 | Cable-Electrical; (00-Ga, Red)(411-cm) | 0 |
| 15***54 | Cable-Electrical; (00-Ga, Black)(411-cm) | 0 |
149-6401 Battery Gp
| 13***54 | Mounting Group-Battery | 1 |
| 14***01 | Battery Group | 1 |
| 6I***64 | Battery Group | 1 |
6i-3164 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
133-6295 Box Gp-Cable Storage
| 0S***79 | Bolt 5.08 cm(2 In.) Long | 20 |
| 13***95 | Box Group-Cable Storage | 1 |
| 13***66 | Handle-Door | 2 |
144-0409 Box Gp-Connection
| 12***26 | Plug-Female; (30 Amp, 125 Volt) | 1 |
| 12***27 | Receptacle; (125-Volt, 30-Ampere) | 1 |
| 12***28 | Plug-Female; (30 Amp, 250 Volt) | 1 |
144-0408 Box Gp-Connection
| 12***28 | Plug-Female; (30 Amp, 250 Volt) | 2 |
| 12***29 | Receptacle; (250-Volt, 30-Ampere) | 2 |
| 13***28 | Film-Information; (Switchgear Phase Ident.) | 1 |
4p-4969 Box Gp-Extension Terminal
| 03***21 | Bolt; (5/16-18x0.625-In) | 10 |
| 2S***47 | Grommet 12.7 mm(.50 In.) Thick) | 1 |
| 4P***82 | Plate-Extension Box | 1 |
267-8480 Box Gp-Terminal -240-Volt Receptacle
| 15***21 | Box | 1 |
| 15***60 | Plate; (Stainless Steel) | 1 |
| 16***44 | Receptacle; (250-Volt, 15-Ampere) | 1 |
102-6843 Box Gp-Terminal
| 10***43 | Box Group-Terminal | 1 |
| 15***21 | Box | 1 |
| 15***60 | Plate; (Stainless Steel) | 1 |
134-0959 Bus Bar Gp
| 12***56 | Insulator; (600-Volt Standoff) | 4 |
| 13***59 | Bus Bar Group | 1 |
270-4537 Circuit Breaker As
| 24***30 | Kit-Bolt; (Circuit Breaker) | 1 |
| 24***27 | Fastener Group; (Bus Bar Box) | 3 |
| 24***47 | Terminal-Circuit Breaker | 1 |
126-1288 Circuit Breaker Gp
| 10***32 | Circuit Breaker Group; (700-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***95 | Bar As | 2 |
108-1062 Circuit Breaker Gp
| 10***34 | Circuit Breaker Group; (1000-Ampere) | 1 |
| 10***95 | Bar As | 2 |
| 10***96 | Bar As | 1 |
270-4658 Circuit Breaker Gp
| 10***95 | Bar As | 2 |
| 10***96 | Bar As | 1 |
| 27***37 | Circuit Breaker As; -1200-Ampere | 1 |
108-1061 Circuit Breaker Gp
| 10***35 | Circuit Breaker Group; (1200-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***95 | Bar As | 2 |
108-1063 Circuit Breaker Gp
| 10***33 | Circuit Breaker Group | 1 |
| 10***95 | Bar As | 2 |
| 10***96 | Bar As | 1 |
6t-3645 Circuit Breaker Gp
| 6T***45 | Circuit Breaker Group; -60-Ampere | 1 |
| 6V***78 | Nut; (10-32-Thd) | 2 |
| 8F***34 | Lockwasher; (External Teeth) | 2 |
202-7904 Conduit Gp-Electrical
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 3 |
| 15***86 | Insert-Nut | 18 |
| 15***76 | Harness As-Wiring | 1 |
209-9170 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 12 |
| 15***05 | Body; (Unilet) | 2 |
| 15***91 | Channel; (426-cm) | 0 |
209-9377 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 24 |
| 15***05 | Body; (Unilet) | 4 |
| 15***91 | Channel; (426-cm) | 0 |
209-8174 Conduit Gp-Electrical
| 19***26 | Clamp; (Conduit) | 2 |
| 20***18 | Connector; (1/2 X 14 Npt) | 4 |
| 20***25 | Connector; (Tee 1/2-14 Npt) | 2 |
208-0720 Conduit Gp-Electrical
| 11***14 | End-Wire; (18-Ga) | 20 |
| 11***97 | End-Wire; (14-Ga) | 44 |
| 11***61 | End-Wire; (10-Ga) | 20 |
209-8272 Conduit Gp-Electrical
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 6 |
| 19***26 | Clamp; (Conduit) | 6 |
| 20***18 | Connector; (1/2 X 14 Npt) | 10 |
211-4369 Conduit Gp-Electrical
| 10***43 | Box Group-Terminal | 1 |
| 15***86 | Insert-Nut | 6 |
| 15***91 | Channel; (426-cm) | 0 |
232-3654 Conduit Gp-Electrical
| 10***52 | Connector-Flexible | 2 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 3 |
| 15***86 | Insert-Nut | 18 |
209-9351 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 18 |
| 15***05 | Body; (Unilet) | 3 |
| 15***91 | Channel; (426-cm) | 0 |
209-9678 Conduit Gp-Electrical
| 15***86 | Insert-Nut | 2 |
| 15***91 | Channel; (426-cm) | 0 |
| 19***26 | Clamp; (Conduit) | 1 |
267-8481 Conduit Gp-Electrical
| 19***26 | Clamp; (Conduit) | 2 |
| 20***18 | Connector; (1/2 X 14 Npt) | 4 |
| 20***25 | Connector; (Tee 1/2-14 Npt) | 2 |
211-4370 Conduit Gp-Electrical
| 10***43 | Box Group-Terminal | 1 |
| 15***86 | Insert-Nut | 6 |
| 15***91 | Channel; (426-cm) | 0 |
209-8419 Conduit Gp-Electrical
| 19***26 | Clamp; (Conduit) | 6 |
| 20***16 | Elbow; (1/2-14 Npt) | 1 |
| 20***18 | Connector; (1/2 X 14 Npt) | 6 |
151-5673 Connection Gp-Electrical
| 15***85 | Duct As-Cable | 1 |
| 15***73 | Connection Group-Electrical | 1 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 1 |
4p-4635 Connection Gp-Electrical
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 2N***80 | Screw-Machine; (10-24x0.75-In) | 3 |
| 4B***47 | Nut,Plain,Square Circuit Breaker Uoc:Bsv,Bsx | 3 |
159-3241 Connection Gp-Electrical
| 10***86 | Marker | 1 |
| 12***30 | Bracket | 1 |
| 12***31 | Bracket | 1 |
147-2673 Connection Gp-Electrical
| 14***73 | Connection Group-Electrical | 1 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
| 4L***55 | Cable As; (0000-Ga) | 2 |
249-4057 Connection Gp-Electrical
| 24***57 | Connection Group-Electrical | 1 |
| 3L***36 | Spacer-Bracket To Diesel Water Passage Cover | 1 |
| 3L***04 | Shield-Terminal | 1 |
151-5675 Connection Gp-Electrical
| 15***11 | Fastener As | 4 |
| 15***46 | Isolator | 4 |
| 15***84 | Duct As-Cable | 1 |
6i-2026 Connection Gp-Electrical
| 10***86 | Marker | 1 |
| 12***30 | Bracket | 1 |
| 12***31 | Bracket | 1 |
103-8974 Connection Gp-Electrical
| 10***74 | Connection Group-Electrical | 1 |
| 10***80 | Film-Identification; (Terminal Marker) | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 20 |
5n-0591 Control Gp-Manual Voltage
| 5N***91 | Control Group-Electronic | 1 |
| 5N***03 | Varistor As | 1 |
| 5N***05 | Plate-Switch | 1 |
191-8573 Control Gp-Solenoid -Fuel Control
| 18***36 | Relay As; (24-Volt) | 1 |
| 19***73 | Control Group-Solenoid; -Fuel Control | 1 |
| 4W***90 | Block-Fuse | 1 |
252-7646 Cover Gp-Circuit Breaker
| 09***72 | Screw-Machine; (M4x0.7x16-mm) | 2 |
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 25***46 | Cover Group-Circuit Breaker; -Circuit Breaker | 1 |
270-4636 Cover Gp-Extension Box
| 25***46 | Cover Group-Circuit Breaker; -Circuit Breaker | 1 |
| 27***35 | Cover | 1 |
| 27***36 | Cover Group-Extension Box | 1 |
108-1056 Cover Gp-Extension Box
| 10***98 | Cover As-Extension | 1 |
| 10***56 | Cover Group-Extension Box | 1 |
| 4L***50 | Nut-Self Lock; (No.10.Unf) | 2 |
241-2624 Cover-Extension Box
| 24***24 | Cover-Extension Box | 1 |
4p-4786 Cover-Extension Box
| 4P***86 | Cover-Extension Box | 1 |
108-1055 Fastener Gp-Extension Box
| 03***21 | Bolt; (5/16-18x0.625-In) | 18 |
| 10***55 | Fastener Group-Extension Box | 1 |
7c-6393 Fastener Gp-Wiring Harness
| 2W***19 | Wire As | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 13 |
| 3S***89 | Bracket | 2 |
242-9752 Harness As-Power -Digital Voltage Regulator
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Terminal As-Ring | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
240-6834 Harness As-Wiring -Emcp Ii
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 10 |
| 24***34 | Harness As-Wiring; -Emcp Ii | 1 |
102-5955 Harness As-Wiring -Control Panel
| 10***55 | Harness As-Wiring; -Control Panel | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
242-3104 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 22 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
200-2316 Harness As-Wiring
| 10***55 | Harness As-Wiring; -Control Panel | 1 |
| 20***16 | Harness As-Wiring | 1 |
240-6833 Harness As-Wiring -Ignition, Lh
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
243-4271 Harness As-Wiring -Generator Terminal Strip
| 23***56 | Plug-Connector; (6-Pin) | 1 |
| 23***57 | Plug-Connector; (9-Pin) | 1 |
| 23***58 | Plug-Connector; (12-Pin) | 1 |
242-3100 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 24 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***66 | Wedge-Plug Lock; (3-Pin) | 1 |
152-2876 Harness As-Wiring
| 15***76 | Harness As-Wiring | 1 |
166-7152 Heater Gp-Battery
| 16***25 | Pad-Heater | 1 |
| 16***26 | Pad-Heater | 3 |
| 16***27 | Cable-Heater; (6-Foot) | 1 |
165-9207 Heater Gp-Battery
| 16***25 | Pad-Heater | 1 |
| 16***26 | Pad-Heater | 1 |
| 16***27 | Cable-Heater; (6-Foot) | 1 |
166-7153 Heater Gp-Battery
| 16***09 | Cable-Heater; (6-Foot) | 1 |
| 16***10 | Pad-Heater | 1 |
| 16***11 | Pad-Heater | 3 |
165-9208 Heater Gp-Battery
| 16***08 | Heater Group-Battery | 1 |
| 16***09 | Cable-Heater; (6-Foot) | 1 |
| 16***10 | Pad-Heater | 1 |
201-9523 Heater Gp-Fuel
| 15***25 | Element-Heating; (240-Volt, 2000-Watt) | 2 |
| 15***23 | Separator Group-Water | 1 |
| 20***23 | Heater Group-Fuel | 1 |
7e-6247 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 7E***47 | Heater Group-Jacket Water | 1 |
7e-6248 Heater Gp-Jacket Water
| 10***32 | Thermostat; (60 Deg F To 160 Deg F)(Jacket Water Heater) | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
200-6504 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 20***04 | Heater Group-Jacket Water | 1 |
9x-1439 Lamp Gp-Flood
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 1 |
| 8T***33 | Nut (M10x1.50 Thd) | 1 |
177-4564 Lighting Gp-Flood
| 15***21 | Box | 1 |
| 17***64 | Lighting Group-Flood | 1 |
| 17***37 | Timer As; (60-Minute) | 1 |
146-9052 Lighting Gp-Generator
| 14***52 | Lighting Group-Generator | 1 |
| 16***36 | Lamp; (240-Volt, 100-Watt) | 3 |
| 16***44 | Receptacle; (250-Volt, 15-Ampere) | 1 |
131-5025 Lighting Gp-Generator
| 13***25 | Lighting Group-Generator | 1 |
| 17***99 | Receptacle; (120-Volt) | 1 |
| 17***00 | Switch-Electric; (120-Volt Light)(Generator Lighting) | 1 |
102-8447 Lighting Gp-Generator
| 10***47 | Lighting Group-Generator | 1 |
213-0420 Mounting Gp -Switch Gear
| 15***46 | Isolator | 6 |
| 21***20 | Mounting Group; -Switch Gear | 1 |
| 7X***87 | Washer; (10.26x22.22x1.9-mm Thk) | 6 |
138-4554 Mounting Gp-Battery
| 03***99 | Nut-Wing; (1/4-20-Thd) | 3 |
| 13***52 | Bracket | 1 |
| 13***54 | Mounting Group-Battery | 1 |
103-7286 Mounting Gp-Circuit Breaker
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 10***86 | Mounting Group-Circuit Breaker | 1 |
| 10***89 | Plate As | 1 |
4p-4968 Mounting Gp-Circuit Breaker
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 4 |
| 4P***85 | Bracket | 1 |
129-4651 Mounting Gp-Circuit Breaker
| 12***86 | Angle-Mounting | 2 |
| 12***87 | Angle-Mounting | 2 |
| 12***88 | Bracket; (Lower) | 1 |
270-4657 Mounting Gp-Circuit Breaker
| 27***45 | Bracket | 1 |
| 27***57 | Mounting Group-Circuit Breaker | 1 |
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
7c-4366 Mounting Gp-Contactor
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 4J***22 | Seal-Interface Between 3rd & Tilt Valve | 1 |
102-9942 Mounting Gp-Contactor
| 10***42 | Mounting Group-Contactor | 1 |
| 3B***63 | Nipple-Pipe | 1 |
| 3B***21 | Bushing-Reducing; (.375in External Thread) | 1 |
7w-3868 Mounting Gp-Jacket Wtr Heater
| 00***62 | Elbow-External Pipe Thread | 1 |
| 00***50 | Adapter-Pipe | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 6 |
106-9697 Neutral Bus Bar As
| 10***97 | Neutral Bus Bar As | 1 |
| 3B***06 | Washer,Lock; Flange,Elbow,Clamp Assembly,Tube To Pump,Tube Assembly To Screen,Clip Mounting,And Tube Assembly To Transmission | 4 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 2 |
262-5313 Plug Gp-Auxiliary Power
| 21***43 | Plug Group-Auxiliary Power | 1 |
| 26***13 | Plug Group-Auxiliary Power | 1 |
| 5S***49 | Bolt; (1/4-20x0.5-In)(1/4-20x.5in) | 14 |
213-4743 Plug Gp-Auxiliary Power
| 20***92 | Receptacle As | 3 |
| 20***06 | Plate | 1 |
| 21***60 | Box As | 1 |
138-3809 Relay As -Power
| 13***09 | Relay As; (Heater Control)(24 Vdc Pump Energize) | 1 |
140-6390 Relay Gp -Time Delay
| 12***44 | Relay-Time Delay; Relay-3 Phase Overvoltage, | 1 |
| 14***90 | Relay Group; -Time Delay | 1 |
131-1976 Relay Gp -Overcurrent
| 11***59 | Relay-Time Delay; (Overcurrent) | 1 |
| 13***76 | Relay Group; -Overcurrent | 1 |
129-4011 Relay Gp
| 10***41 | Spring-Relay | 1 |
| 11***41 | Socket-Relay | 1 |
| 12***15 | Relay; (10-Ampere, 24-Volt)(Fuel Level) | 1 |
140-6391 Relay Gp -Time Delay
| 12***45 | Relay-Time Delay; Relay-3 Phase Overvoltage, | 1 |
| 14***91 | Relay Group; -Time Delay | 1 |
128-3326 Relay Gp -Auxiliary
| 12***26 | Relay Group; -Auxiliary | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
140-6392 Relay Gp -Time Delay
| 12***46 | Relay-Time Delay; (416-Volt) | 1 |
| 14***92 | Relay Group; -Time Delay | 1 |
158-6181 Relay Gp
| 15***81 | Relay Group; -Engine Failure | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
140-6393 Relay Gp -Time Delay
| 12***47 | Relay-Time Delay; Relay-3 Phase Overvoltage, | 1 |
| 14***93 | Relay Group; -Time Delay | 1 |
134-1157 Relay Gp -Engine Failure
| 12***26 | Relay Group; -Auxiliary | 1 |
| 13***57 | Relay Group; -Engine Failure | 1 |
| 15***81 | Relay Group; -Engine Failure | 1 |
140-6394 Relay Gp -Time Delay
| 12***58 | Relay-Time Delay; (575-Volt) | 1 |
| 14***94 | Relay Group; -Time Delay | 1 |
105-2048 Sensor & Mtg Gp-Radiator
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***48 | Sensor & Mtg Group-Radiator | 1 |
| 11***52 | Harness As-Sensor; (Coolant Level) | 1 |
105-2049 Sensor & Mtg Gp-Radiator
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***49 | Sensor & Mtg Group-Radiator | 1 |
| 11***53 | Harness As-Sensor; (Coolant) | 1 |
111-3794 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***94 | Sensor Group-Coolant Level; -Coolant Loss-Aftercooler, Jacket Water | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
165-6634 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***34 | Sensor Group-Coolant Level; (Water, Coolant)(Scac Expansion Tank) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
146-9381 Sensor Gp-Fuel Level
| 12***49 | Lockwasher | 1 |
| 12***50 | Nut; (1-11/16-18-Thd) | 1 |
| 14***33 | Gasket | 1 |
146-9431 Sensor Gp-Fuel Level
| 12***49 | Lockwasher | 1 |
| 12***50 | Nut; (1-11/16-18-Thd) | 1 |
| 14***33 | Gasket | 1 |
204-2518 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 20***18 | Sensor Group-Liquid Level; (Jacket Water) | 1 |
3e-3761 Sensor Gp-Liquid Level
| 11***94 | Sensor Group-Coolant Level; -Coolant Loss-Aftercooler, Jacket Water | 1 |
| 3E***61 | Sensor Group-Liquid Level | 1 |
239-9957 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 23***57 | Sensor Group-Liquid Level; -Coolant Loss | 1 |
216-8684 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***39 | Pin-Connector; (14-Ga To 18-Ga)(For 14 Gauge Wire) | 3 |
| 21***84 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
145-2362 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 14***62 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
4p-7610 Sensor Gp-Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***49 | Strap; (Marker) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
102-0050 Sensor Gp-Temperature
| 10***50 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
5n-8293 Shutoff Gp-Electrical
| 10***15 | Cover-Terminal | 2 |
| 1W***70 | Switch As-Start | 1 |
| 2W***34 | Wire As | 1 |
111-7760 Shutoff Gp-Electrical
| 10***48 | Diode As-Suppressor | 1 |
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
| 11***24 | Block-Contact; (1-Pole)(Normally Closed) | 1 |
165-1677 Shutoff Gp-Electrical
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
| 11***23 | Block-Contact; (1-Pole)(Normally Open) | 1 |
| 11***24 | Block-Contact; (1-Pole)(Normally Closed) | 2 |
111-7761 Shutoff Gp-Electrical
| 10***19 | Control Group-Emcp Electronic | 1 |
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
| 11***23 | Block-Contact; (1-Pole)(Normally Open) | 2 |
4n-1061 Starting Motor Gp-Electric
| 4N***59 | Gasket; (Starting Motor) | 1 |
| 4N***61 | Starting Motor Group-Electric | 1 |
| 6V***90 | Starting Motor Group-Electric; (Delco Remy) | 1 |
237-1962 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 13 |
6v-0890 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
338-3454 Starting Motor Gp-Electric
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 4 |
170-5400 Strip Gp-Terminal -Main
| 17***00 | Strip Group-Terminal; -Main | 1 |
| 22***24 | Support As | 1 |
| 22***25 | Plate-Tread | 1 |
170-5395 Strip Gp-Terminal -Thermocouple
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 15***55 | Fuse; (10-Ampere) | 2 |
| 17***95 | Strip Group-Terminal; -Thermocouple | 1 |
176-1057 Support Gp-Battery
| 17***57 | Support Group-Battery | 1 |
162-0572 Switch As
| 16***72 | Switch As; -Prelubrication | 1 |
105-7931 Switch As-Auxiliary
| 10***31 | Switch As-Auxiliary; -Circuit Breaker | 1 |
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
7n-0718 Switch Gp-Disconnect -Battery
| 11***21 | Plate; (Electrical Switch) | 1 |
| 17***33 | Bracket | 1 |
| 3L***04 | Shield-Terminal | 2 |
141-1598 Switch Gp-Disconnect -Battery
| 14***98 | Switch Group-Disconnect; -Battery | 1 |
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 6 |
| 6T***31 | Nut-Hexagon-(15/32-32 Thd) | 2 |
131-1967 Switch Gp-Governor
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
| 11***23 | Block-Contact; (1-Pole)(Normally Open) | 1 |
| 11***24 | Block-Contact; (1-Pole)(Normally Closed) | 2 |
216-0559 Switch Gp-Shutoff
| 21***59 | Switch Group-Shutoff | 1 |
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 3 |
| 6T***31 | Nut-Hexagon-(15/32-32 Thd) | 2 |
131-1977 Switch Gp-Toggle -Starting Aid
| 13***77 | Switch Group-Toggle; -Starting Aid | 1 |
244-4460 Transformer As -Current
| 24***60 | Transformer As; -Current | 1 |
131-1966 Transformer Gp-Current
| 13***66 | Transformer Group-Current | 1 |
269-5223 Transformer-Current
| 11***61 | End-Wire; (10-Ga) | 11 |
| 16***27 | Ferrule-Wire; (14-Ga) | 13 |
| 19***62 | Film-Identification; (Wire)(Label) | 56 |
209-7811 Wiring Gp-Engine
| 18***54 | Terminal-Cable | 40 |
| 20***11 | Wiring Group-Engine | 1 |
| 20***13 | Cable; (Black)(360-Dm) | 0 |
187-1658 Wiring Gp-Generator -Load
| 10***38 | End-Wire; (16-Ga) | 3 |
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
242-7961 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 9 |
| 24***61 | Wiring Group-Generator | 1 |
| 24***01 | Harness As-Wiring; (Vr6 Voltage Regulator) | 1 |
243-4285 Wiring Gp-Generator
| 20***76 | Wire-Electrical | 0 |
| 24***85 | Wiring Group-Generator | 1 |
| 5P***29 | Wire (No. 14 Gauge) 3.05 M(10ft.) | 0 |
241-3379 Wiring Gp-Generator
| 24***79 | Wiring Group-Generator | 1 |
| 24***00 | Harness As-Wiring; -Generator Terminal Strip | 1 |
242-7960 Wiring Gp-Generator
| 24***04 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***60 | Wiring Group-Generator | 1 |
| 24***52 | Harness As-Power; -Digital Voltage Regulator | 1 |
243-4269 Wiring Gp-Generator
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 24***69 | Wiring Group-Generator | 1 |
| 24***71 | Harness As-Wiring; -Generator Terminal Strip | 1 |
241-3378 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 10 |
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 24***68 | Harness As-Wiring; (Voltage Adjustment) | 1 |
209-8234 Wiring Gp-Machine -Lighting
| 10***55 | Harness As-Wiring; -Control Panel | 1 |
| 20***34 | Wiring Group-Machine; -Lighting | 1 |
| 7C***93 | Fastener Group-Wiring Harness | 1 |
103-1965 Wiring Gp-Panel
| 10***81 | Awning Group-Louver | 4 |
| 10***65 | Wiring Group-Panel | 1 |
Enclosures, Guards And Bases
103-0684 Awning Ar-Louver
| 03***12 | Rivet (To Fuel Tank) | 44 |
| 10***84 | Awning Ar-Louver | 1 |
| 16***36 | Louver As | 1 |
102-8406 Awning Gp-Louver
| 03***12 | Rivet (To Fuel Tank) | 44 |
| 10***06 | Awning Group-Louver | 1 |
| 2Y***20 | Screw; (1/4-20x0.75-In)(Machine) | 14 |
103-0681 Awning Gp-Louver
| 10***81 | Awning Group-Louver | 1 |
| 11***20 | Door As-Radiator | 1 |
| 13***86 | Door As | 1 |
164-7086 Container Ar
| 11***20 | Door As-Radiator | 1 |
| 13***86 | Door As | 1 |
| 13***98 | Floorplate-Galvanized | 9 |
168-8623 Container Ar
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 16***23 | Container Ar | 1 |
| 5N***67 | Seal; 1.52mm(.059in)Thk | 3 |
4p-1802 Cover Gp-Generator
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 4 |
| 16***96 | Nut; (1/4-20-Thd)(Self-Clinching) | 6 |
| 2D***35 | Locknut (Visor To Bracket) | 6 |
134-2786 Door As
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 15 |
| 13***86 | Door As | 1 |
| 14***27 | Handle-Door | 1 |
156-9152 Door As
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 6 |
| 15***25 | Rod Group-Access Door | 1 |
| 15***78 | Hinge | 3 |
161-2492 Door As
| 16***92 | Door As | 1 |
164-4580 Door As
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 10 |
| 15***52 | Door As | 1 |
| 15***68 | Angle | 1 |
204-5718 Door Gp-Access -Enclosure
| 14***00 | Bellow-Cable | 1 |
| 14***03 | Support-Ca Tray | 3 |
| 14***05 | Adapter-Ca Tray | 1 |
150-6884 Duct As-Cable
| 14***00 | Bellow-Cable | 1 |
| 14***03 | Support-Ca Tray | 2 |
| 14***05 | Adapter-Ca Tray | 1 |
150-6885 Duct As-Cable
| 14***09 | Bolt; (Self-Tapping) | 4 |
| 14***84 | Deflector As | 1 |
| 15***85 | Duct As-Cable | 1 |
149-5237 Enclosure Gp-Generator
| 14***37 | Adapter-Screen | 2 |
| 14***37 | Enclosure Group-Generator | 1 |
| 4M***61 | Bolt-To Assemble Valve As And Plates | 28 |
149-7755 Enclosure Gp-Generator
| 14***55 | Enclosure Group-Generator | 1 |
156-9155 Handle As
| 15***49 | Sheet | 7 |
| 15***50 | Insulation | 56 |
| 15***55 | Handle As; -Door | 1 |
152-8796 Insulation Gp-Generator
| 15***36 | Panel Group-Sound Suppression | 1 |
| 15***38 | Panel; (Sound) | 14 |
| 15***40 | Panel; (Sound) | 7 |
152-8793 Insulation Gp-Generator
| 15***35 | Panel Group-Sound Suppression | 1 |
| 15***40 | Panel; (Sound) | 21 |
| 15***93 | Insulation Group-Generator | 1 |
152-8797 Insulation Gp-Generator
| 15***97 | Insulation Group-Generator | 1 |
152-8792 Insulation Gp-Generator
| 15***37 | Panel | 22 |
| 15***38 | Panel; (Sound) | 9 |
| 15***41 | Angle | 12 |
152-1148 Insulation Gp-Generator
| 15***39 | Panel; (Sound) | 24 |
| 15***40 | Panel; (Sound) | 11 |
| 15***48 | Insulation Group-Generator | 1 |
9y-1391 Ladder As
| 26***02 | Bracket-Latch | 3 |
| 26***03 | Latch | 2 |
| 6C***79 | Rivet-Pop | 16 |
203-0218 Latch Gp-Access Door -Enclosure
| 10***47 | Lighting Group-Generator | 3 |
| 17***99 | Receptacle; (120-Volt) | 1 |
| 17***00 | Switch-Electric; (120-Volt Light)(Generator Lighting) | 1 |
102-6849 Lighting Ar
| 10***49 | Lighting Ar | 1 |
| 10***06 | Awning Group-Louver | 1 |
169-5445 Louver Ar
| 16***45 | Louver Ar | 1 |
169-5444 Louver Ar
| 15***31 | Louver Group | 1 |
| 16***44 | Louver Ar | 1 |
169-5442 Louver Ar
| 16***04 | Louver Group | 1 |
| 16***42 | Louver Ar | 1 |
102-8404 Louver As
| 10***04 | Louver As | 1 |
| 12***67 | Actuator | 1 |
| 15***08 | Bearing | 34 |
163-0103 Louver As
| 03***12 | Rivet (To Fuel Tank) | 44 |
| 12***67 | Actuator | 1 |
| 15***08 | Bearing | 34 |
102-8401 Louver As
| 10***01 | Louver As | 1 |
| 12***67 | Actuator | 1 |
| 15***08 | Bearing | 34 |
102-8402 Louver As
| 10***02 | Louver As | 1 |
167-2035 Louver As
| 12***67 | Actuator | 1 |
| 15***08 | Bearing | 16 |
| 16***35 | Louver As | 1 |
102-8405 Louver As
| 03***12 | Rivet (To Fuel Tank) | 44 |
| 10***05 | Louver As, . Casing; Gear, Case | 1 |
| 12***67 | Actuator | 1 |
191-3518 Louver As
| 10***81 | Awning Group-Louver | 1 |
| 19***18 | Louver As | 1 |
| 4D***16 | Rivet-Pop | 40 |
167-3904 Louver Gp
| 16***04 | Louver Group | 1 |
| 19***18 | Louver As | 1 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 18 |
201-9102 Louver Gp
| 11***76 | Washer-Snubbing | 2 |
| 15***22 | Plate As | 1 |
| 16***61 | Screw; (5/16x1.25-In) | 3 |
154-6731 Louver Gp
| 15***31 | Louver Group | 1 |
| 16***03 | Louver As | 1 |
| 4D***16 | Rivet-Pop | 40 |
163-4716 Louver Gp
| 16***16 | Louver Group | 1 |
| 16***35 | Louver As | 1 |
| 4D***16 | Rivet-Pop | 40 |
155-1701 Mounting Gp-Power Module
| 15***90 | Mounting Group-Engine | 14 |
| 15***01 | Mounting Group-Power Module | 1 |
178-6325 Mounting Gp-Vibration Isolator
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 17***25 | Mounting Group-Vibration Isolator | 1 |
| 1F***60 | Nipple-Pipe | 1 |
161-7354 Mounting Gp-Vibration Isolator
| 15***46 | Isolator | 4 |
| 16***54 | Mounting Group-Vibration Isolator | 1 |
| 8T***96 | Washer-Hard- Line From Pipe As. To Gear | 4 |
7e-1109 Rail Gp-Engine & Gen Support
| 14***30 | Guide As | 1 |
| 14***31 | Guide As | 1 |
| 14***33 | Screw-Torx Head | 30 |
141-3229 Rail Gp-Slide
| 14***29 | Rail Group-Slide | 1 |
| 15***36 | Rod | 1 |
| 16***95 | Bracket | 1 |
151-5625 Rod Gp-Access Door
| 15***25 | Rod Group-Access Door | 1 |
| 2D***35 | Locknut (Visor To Bracket) | 8 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 8 |
155-7444 Shield As
| 15***44 | Shield As | 1 |
| 2D***35 | Locknut (Visor To Bracket) | 11 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 11 |
155-7445 Shield As
| 15***44 | Shield As | 1 |
| 15***45 | Shield As | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 8 |
202-3199 Shield Gp
| 15***45 | Shield As | 1 |
| 20***99 | Shield Group | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 11 |
202-3200 Shield Gp
| 20***00 | Shield Group | 1 |
149-1396 Support As -Reinforcement Base
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 13***90 | Cable As | 1 |
| 14***96 | Support As; -Reinforcement Base | 1 |
Engine Arrangement
189-8854 Engine Ar-Complete
| 14***55 | Pump Group-Fuel Priming | 1 |
| 14***45 | Lines Group-Engine Oil Drain | 1 |
| 18***54 | Engine Ar-Complete | 1 |
190-0986 Engine Ar-Core
| 12***12 | Plug Group-Cylinder Block | 1 |
| 19***86 | Engine Ar-Core | 1 |
| 2W***54 | Piston & Rod Group; Connecting Rod & Piston Group | 12 |
189-5352 General Ar
| 18***52 | General Ar | 1 |
| 18***54 | Engine Ar-Complete | 1 |
Fuel System
7w-6653 Actuator As-Governor
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
4w-5391 Box As-Governor Preregulator
| 4W***91 | Box As-Preregulator | 1 |
| 7T***37 | Fuse; (0.75-Ampere) | 3 |
7e-8396 Control Gp-Fuel -Auxiliary
| 3T***70 | Relay As-24 Volt; (24 Volt) | 1 |
| 4W***90 | Block-Fuse | 1 |
| 7E***96 | Control Group-Fuel; -Auxiliary | 1 |
6n-1656 Drive Gp-Governor
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 1 |
| 1B***35 | Key-Woodruff | 1 |
| 1F***22 | Bearing (.500" Long) | 1 |
6n-8171 Drive Gp-Governor & Fuel Pump
| 4W***87 | Gear-Fuel Pump Drive; (86-Teeth) | 1 |
| 5J***93 | Bolt-12 Point Head; (1/2-13x1.75-In)(Marked Z) | 4 |
| 6N***71 | Drive Group-Governor & Fuel Pump; Governor And Fuel Pump Drive Group | 1 |
6n-4703 Fastener Gp-Governor
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 1 |
| 1B***04 | Spacer; (6.8x10x9.5-mm Thk) | 1 |
| 1D***16 | Nut,Plain,Hexagon Clip Uoc:Bsv,Bsx | 2 |
4n-6925 Filter Gp-Fuel
| 1R***49 | Filter-Fuel; (Advanced Efficiency)(Secondary) | 2 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 4N***25 | Filter Group-Fuel; Filter Group-Fuel | 1 |
7e-1232 Governor As-Electronic
| 11***56 | Washer; (5.6x7.8x0.5-mm Thk) | 1 |
| 13***55 | Control As-Governor | 1 |
| 3K***82 | Fuse; (10-Ampere) | 1 |
4p-2788 Governor As-Electronic
| 13***53 | Control As-Governor | 1 |
| 4P***88 | Governor As-Electronic | 1 |
| 4W***71 | Potentiometer; (100-Ohm)(Engine Speed Control) | 1 |
4w-9314 Governor As-Electronic
| 13***53 | Control As-Governor | 1 |
| 4W***91 | Box As-Preregulator | 1 |
| 4W***71 | Potentiometer; (100-Ohm)(Engine Speed Control) | 1 |
4w-9313 Governor As-Electronic
| 13***53 | Control As-Governor | 1 |
| 4W***71 | Potentiometer; (100-Ohm)(Engine Speed Control) | 1 |
| 4W***72 | Knob; (Engine Speed Control) | 1 |
4n-2117 Housing Gp-Fuel Pump
| 1P***32 | Ball,Bearing | 12 |
| 1P***34 | Pin,Grooved | 12 |
| 1S***99 | Dowel | 1 |
3n-6668 Lines Gp-Flexible Fuel
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 2L***31 | Connector-Pipe | 2 |
| 3N***67 | Hose Assem. | 2 |
229-9548 Lines Gp-Fuel
| 03***06 | Adapter-Pipe; (To Transmission) | 2 |
| 21***97 | Screw; (5/16-18x2.5-In) | 8 |
| 22***48 | Lines Group-Fuel | 1 |
7w-1077 Lines Gp-Fuel Filter
| 03***42 | Elbow Hose Assembly To | 1 |
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 3 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
6i-0349 Lines Gp-Fuel Injection
| 10***32 | Bracket As | 1 |
| 10***39 | Screw As | 6 |
| 11***17 | Plate | 1 |
6i-0350 Lines Gp-Fuel Injection
| 10***31 | Plate As | 1 |
| 10***28 | Name-Plate (Name Of Machine: Zaxis210lck), Clamp As; (Non-Threaded) | 2 |
| 1W***68 | Clamp-Fuel Line; (Non-Threaded)(Thru Hole) | 1 |
7w-0404 Lines Gp-Fuel Injection
| 06***38 | Spacer; (11.12x19.05x7.9-mm Thk) | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 10***39 | Screw As | 6 |
4w-7020 Nozzle As-Fuel Valve
| 11***62 | Seal-O-Ring | 1 |
| 27***89 | Seal-Washer | 1 |
| 4W***20 | Nozzle As-Fuel Valve | 1 |
207-4512 Pump As-Fuel Transfer
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 5 |
| 20***12 | Pump As-Fuel Transfer | 1 |
141-7898 Pump As-Fuel Transfer
| 14***98 | Pump As-Fuel Transfer | 1 |
| 17***07 | Pump As-Fuel Transfer | 1 |
| 17***08 | Motor As | 1 |
170-4007 Pump As-Fuel Transfer
| 17***07 | Pump As-Fuel Transfer | 1 |
| 17***09 | Gasket | 1 |
| 17***10 | Seal | 1 |
4w-6073 Pump Gp-Fuel Injection
| 03***15 | Bolt 5t***53 Cable As To 5t***18 Lever | 1 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 3 |
| 11***18 | Seal-O-Ring; (26.64mm Id) | 12 |
7w-0561 Pump Gp-Fuel Injection
| 1W***87 | Valve As-Check; (Fuel Injection Pump) | 1 |
| 1W***71 | Bonnet-Valve | 1 |
| 7C***78 | Bolt-Plunger Gear; (Fuel Pump) | 1 |
145-8855 Pump Gp-Fuel Priming
| 13***41 | Pump Group-Fuel Priming; (Hand) | 1 |
| 14***55 | Pump Group-Fuel Priming | 1 |
| 1B***90 | Bolt; (5/16-18x1.375-In)(Rh Front Cover) | 1 |
4w-5477 Pump Gp-Fuel Transfer
| 13***36 | Gasket-Liquid; (8-Oz Can) | 0 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 1W***77 | Shaft-Idler | 1 |
4n-1101 Pump Gp-Fuel Transfer
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 2D***76 | Bearing-Flange | 1 |
| 4N***91 | Housing Assem. | 1 |
4w-6074 Pump Gp-Gov Drv,Fuel Inj & Tfr
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 1F***03 | Lever-Governor | 1 |
233-7973 Separator Gp-Water -Primary Fuel Filter
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 23***73 | Separator Group-Water; -Primary Fuel Filter | 1 |
4p-7380 Separator Gp-Water
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 4 |
103-0183 Separator Gp-Water
| 10***83 | Separator Group-Water | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 2 |
241-0879 Tank As-Fuel
| 20***47 | Cap; (Fuel Filler), . Seal; Group | 2 |
| 24***79 | Tank As-Fuel | 1 |
| 3B***90 | Coupling-Pipe | 1 |
147-5682 Tank As-Fuel
| 10***83 | Separator Group-Water | 1 |
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***84 | Film-Information; (Venting Requirements) | 1 |
147-5685 Tank As-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***81 | Sensor Group-Fuel Level | 1 |
| 14***85 | Tank As-Fuel | 1 |
147-6187 Tank As-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***84 | Film-Information; (Venting Requirements) | 1 |
| 14***31 | Sensor Group-Fuel Level; (Level) | 1 |
208-9211 Tank As-Fuel
| 20***47 | Cap; (Fuel Filler), . Seal; Group | 2 |
| 20***11 | Tank As-Fuel | 1 |
| 3B***90 | Coupling-Pipe | 1 |
210-3179 Tank As-Fuel
| 20***47 | Cap; (Fuel Filler), . Seal; Group | 2 |
| 21***79 | Tank As-Fuel | 1 |
| 3B***90 | Coupling-Pipe | 1 |
211-3211 Tank Gp-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 14***33 | Gasket | 1 |
147-6186 Tank Gp-Fuel
| 11***94 | Bracket | 3 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***18 | Nipple-Pipe | 1 |
191-2418 Tank Gp-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***33 | Gasket | 1 |
| 14***31 | Sensor Group-Fuel Level; (Level) | 1 |
208-9210 Tank Gp-Fuel
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 11***21 | Switch-Level; (Fuel) | 1 |
191-2411 Tank Gp-Fuel
| 11***94 | Bracket | 5 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 15***93 | Clamp-Hose | 1 |
198-0325 Tank Gp-Fuel
| 11***94 | Bracket | 8 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 2 |
| 13***33 | Pipe; (50-cm) | 0 |
213-2380 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 15***10 | Fastener As | 2 |
201-9526 Tank Gp-Fuel
| 11***94 | Bracket | 5 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***18 | Nipple-Pipe | 1 |
201-9527 Tank Gp-Fuel
| 11***94 | Bracket | 5 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 15***10 | Fastener As | 2 |
204-6824 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 15***10 | Fastener As | 2 |
201-9524 Tank Gp-Fuel
| 14***33 | Gasket | 1 |
| 14***81 | Sensor Group-Fuel Level | 1 |
| 15***61 | Step | 1 |
191-2423 Tank Gp-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 14***98 | Pump As-Fuel Transfer | 1 |
211-3210 Tank Gp-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***33 | Gasket | 1 |
| 14***31 | Sensor Group-Fuel Level; (Level) | 1 |
241-0885 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 15***10 | Fastener As | 2 |
241-0884 Tank Gp-Fuel
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***33 | Gasket | 1 |
141-7901 Tank Gp-Fuel
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 1 |
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 2 |
| 14***01 | Tank Group-Fuel | 1 |
201-9525 Tank Gp-Fuel
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***33 | Gasket | 1 |
| 14***81 | Sensor Group-Fuel Level | 1 |
141-7896 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 14***96 | Tank Group-Fuel | 1 |
| 14***85 | Tank As-Fuel | 1 |
212-0209 Tank Gp-Fuel
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***68 | Film-Warning; (Transport Restriction) | 1 |
| 14***33 | Gasket | 1 |
191-2408 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 15***10 | Fastener As | 2 |
196-9263 Tank Gp-Fuel
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***75 | Hose-Hydraulic; (21-Inches) | 0 |
| 15***10 | Fastener As | 2 |
153-0180 Vent Gp-Fuel Tank
| 12***08 | Hose-Hydraulic; (21.3-Inches) | 0 |
| 15***80 | Vent Group-Fuel Tank | 1 |
| 3B***92 | Coupling-Pipe; (1-1/2-11-1/2 Npt Thd) | 1 |
Generators
108-1060 Cable Gp-Generator Ground
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 10***60 | Cable Group-Generator Ground | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
108-1058 Cable Gp-Generator Ground
| 10***88 | Cable As | 8 |
| 10***58 | Cable Group-Generator Ground | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 8 |
108-1059 Cable Gp-Generator Ground
| 10***88 | Cable As | 12 |
| 10***59 | Cable Group-Generator Ground | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 16 |
108-1057 Cable Gp-Generator Ground
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 10***57 | Cable Group-Generator Ground | 1 |
| 13***90 | Cable As | 1 |
210-8556 Connection Gp-Generator Leads
| 20***46 | Cable; (0000-Ga)(1279-cm) | 0 |
| 21***56 | Connection Group-Generator Leads | 1 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 36 |
224-5378 Connection Gp-Generator Leads
| 22***78 | Connection Group-Generator Leads | 1 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 12 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 24 |
210-8523 Connection Gp-Generator Leads
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 4 |
| 14***00 | Bellow-Cable | 1 |
| 14***04 | Flange-Bellow | 2 |
142-8324 Connection Gp-Generator Leads
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 14***24 | Connection Group-Generator Leads | 1 |
| 15***46 | Isolator | 4 |
126-0738 Connection Gp-Terminal Strip
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 2 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 12***46 | Resistor | 1 |
168-5049 Conversion Gp-Generator
| 13***26 | Film-Control Panel; (Generator Wiring Diagram) | 1 |
| 16***49 | Conversion Group-Generator | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
342-0548 Generator Ar
| 13***25 | Film-Generator Wiring; (Control Panel) | 1 |
| 34***48 | Generator Ar | 1 |
| 34***11 | Generator Group | 1 |
9y-0449 Generator Ar
| 13***26 | Film-Control Panel; (Generator Wiring Diagram) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 2K***19 | Drive Screw--For Mounting Name Plate | 2 |
9y-1447 Generator Ar
| 13***26 | Film-Control Panel; (Generator Wiring Diagram) | 1 |
| 9Y***47 | Generator Ar | 1 |
332-6412 Generator Ar
| 13***25 | Film-Generator Wiring; (Control Panel) | 1 |
| 33***12 | Generator Ar | 1 |
| 34***47 | Generator Group | 1 |
330-9340 Generator Ar
| 13***25 | Film-Generator Wiring; (Control Panel) | 1 |
| 33***40 | Generator Ar | 1 |
| 34***60 | Generator Group | 1 |
344-2712 Generator Ar
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 10***49 | Stator-Exciter | 1 |
| 10***22 | Retainer | 2 |
9y-0442 Generator Ar
| 13***26 | Film-Control Panel; (Generator Wiring Diagram) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 2K***19 | Drive Screw--For Mounting Name Plate | 2 |
9y-0391 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 10***96 | Stator As-Magnet | 1 |
9y-1429 Generator Gp
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 10***96 | Stator As-Magnet | 1 |
| 10***49 | Stator-Exciter | 1 |
9y-0384 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 10***96 | Stator As-Magnet | 1 |
344-2711 Generator Gp
| 11***56 | Washer; (5.6x7.8x0.5-mm Thk) | 2 |
| 34***11 | Generator Group | 1 |
| 4B***74 | Washer (Required Only When Bosch Alternator Is Fitted) | 2 |
340-5960 Generator Gp
| 10***67 | Coupling Group-Generator | 1 |
| 10***96 | Stator As-Magnet | 1 |
| 10***49 | Stator-Exciter | 1 |
342-0547 Generator Gp
| 10***96 | Stator As-Magnet | 1 |
| 10***49 | Stator-Exciter | 1 |
| 10***22 | Retainer | 2 |
124-3287 Heat Sink As
| 12***87 | Heat Sink As | 1 |
4p-4488 Heat Sink As
| 11***56 | Washer; (5.6x7.8x0.5-mm Thk) | 2 |
| 12***88 | Heat Sink | 1 |
| 2R***59 | Bolt-Socket Head; (10-32x1.5-In) | 2 |
290-5565 Heat Sink As
| 29***65 | Heat Sink As | 1 |
290-5564 Heat Sink As
| 29***64 | Heat Sink As | 1 |
102-6826 Heater As-Space
| 10***26 | Heater As-Space, Carrier | 1 |
175-6987 Heater Gp-Space
| 17***87 | Heater Group-Space | 1 |
| 24***26 | Washer-Hard; (7.2x32x1-mm Thk) | 6 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 1 |
242-3487 Mounting Gp-Voltage Regulator
| 24***87 | Mounting Group-Voltage Regulator | 1 |
| 4L***25 | Lockwasher | 4 |
| 7X***01 | Bolt-Plt; (1/4unc X 1 1/4) | 4 |
123-8591 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
124-1563 Mounting Gp-Voltage Regulator
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 24***26 | Washer-Hard; (7.2x32x1-mm Thk) | 6 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 6 |
130-3481 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 13***81 | Mounting Group-Voltage Regulator | 1 |
| 24***64 | Spacer; (8.5x12.7x94.3-mm Thk) | 3 |
243-4270 Mounting Gp-Voltage Regulator
| 24***70 | Mounting Group-Voltage Regulator | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3820 Regulator As-Voltage
| 15***20 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3821 Regulator As-Voltage
| 15***21 | Regulator As-Voltage | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
155-3832 Regulator As-Voltage -Digital
| 15***32 | Regulator As-Voltage; -Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
309-1019 Regulator As-Voltage -Digital
| 24***58 | Film-Warning; (Shock, Electrocution Hazard)(Shock, Electrocution Hazard) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
155-3835 Regulator As-Voltage -Digital
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
202-8634 Regulator As-Voltage -Digital
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
259-4020 Regulator As-Voltage
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 25***20 | Regulator As-Voltage | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
114-5510 Regulator As-Voltage
| 11***10 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
314-7755 Regulator As-Voltage -Digital
| 30***19 | Regulator As-Voltage; -Digital | 1 |
| 31***55 | Regulator As-Voltage; -Generator | 1 |
| 7E***74 | Film-Instruction; (Voltage Control Adjustment) | 1 |
235-5725 Regulator As-Voltage -Digital
| 23***25 | Regulator As-Voltage; -Digital-Generator | 1 |
| 25***19 | Film-Identification; (Voltage Regulator)(24-Volt Dc) | 1 |
105-4401 Regulator As-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
121-6203 Regulator Gp-Voltage -Digital
| 12***03 | Regulator Group-Voltage; -Digital | 1 |
| 6V***74 | Screw-Machine (6-32x0.25in); (6-32x0.25-In) | 19 |
116-7849 Regulator Gp-Voltage -Digital
| 11***49 | Regulator Group-Voltage; -Digital | 1 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 15***20 | Regulator As-Voltage | 1 |
121-6200 Regulator Gp-Voltage
| 12***00 | Regulator Group-Voltage | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
202-8635 Regulator Gp-Voltage
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
| 20***35 | Regulator Group-Voltage | 2 |
6i-2963 Regulator Gp-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 6I***63 | Regulator Group-Voltage | 1 |
| 7E***74 | Film-Instruction; (Voltage Control Adjustment) | 1 |
108-1870 Regulator Gp-Voltage
| 10***70 | Regulator Group-Voltage | 1 |
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
121-6202 Regulator Gp-Voltage -Digital
| 12***02 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
202-8638 Regulator Gp-Voltage
| 20***38 | Regulator Group-Voltage | 1 |
| 4P***73 | Disc | 2 |
| 5N***32 | Bolt-Special | 16 |
116-7846 Regulator Gp-Voltage -Digital
| 11***46 | Regulator Group-Voltage; -Digital | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
126-5031 Rotor As
| 11***89 | Spacer; (15.9x50.8x6.3-mm Thk) | 4 |
| 12***31 | Rotor As | 1 |
| 15***86 | Insert-Nut | 4 |
126-5028 Rotor As
| 12***28 | Rotor As | 1 |
| 4P***73 | Disc | 1 |
| 5N***32 | Bolt-Special | 16 |
Lubrication System
2n-8220 Breather Gp -Crankcase
| 2N***09 | Clamp; (V-Band) | 1 |
| 2N***20 | Breather Group; Breather Gp-Crankcase | 1 |
| 4F***90 | Seal (2.10" Inside Diameter) | 1 |
4n-2481 Fastener Gp-Oil Pump Mounting -Engine
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 4N***81 | Fastener Group-Oil Pump Mounting; Oil Pump Mounting Fastener Group | 1 |
2w-6537 Filler Gp-Engine Oil
| 12***97 | Tube As | 1 |
| 2N***09 | Clamp; (V-Band) | 1 |
| 2W***37 | Filler Group-Oil | 1 |
4n-2387 Filter Gp-Engine Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 10 |
| 1R***08 | Filter As-Engine Oil; (Advanced Efficiency)(High Efficiency) | 2 |
6n-7305 Fumes Disposal Gp
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 1 |
| 1S***96 | Clip (Tube To Bracket) | 1 |
4p-7773 Fumes Disposal Gp
| 2J***40 | Clamp--To Hose Ends | 4 |
| 4P***73 | Fumes Disposal Group | 1 |
| 4P***64 | Tube As | 2 |
4w-4699 Fumes Disposal Gp
| 4W***99 | Fumes Disposal Group | 1 |
| 4W***88 | Tube; (Fumes Disposal)(Rh) | 1 |
| 4W***91 | Tube; (Fumes Disposal)(Lh) | 1 |
7e-4261 Fumes Disposal Gp
| 4P***80 | Tube As | 2 |
| 5N***33 | Hose; Hose 122 cm (48 In.) | 2 |
| 7E***61 | Fumes Disposal Group | 1 |
2w-9203 Gauge Gp-Oil Level (Dipstick) -Engine
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 1 |
| 11***68 | Seal-O-Ring; (15.54mm Id) | 1 |
2w-9182 Lines Gp-Engine Oil
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 10***78 | Seal-O-Ring; (37.47-mm Id) | 1 |
149-7545 Lines Gp-Engine Oil Drain
| 14***11 | Elbow-90 Degree | 1 |
| 14***45 | Lines Group-Engine Oil Drain | 1 |
| 4P***17 | Valve-Ball; (Jacket Water Heater) | 1 |
204-7439 Lines Gp-Engine Oil Drain
| 14***11 | Elbow-90 Degree | 1 |
| 20***39 | Lines Group-Engine Oil Drain | 1 |
| 3B***80 | Nipple--Priming Pump Bottom | 1 |
4n-2934 Lines Gp-Turbocharger Oil
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
6n-1030 Pump Gp-Engine Oil
| 12***56 | Cover As-Pump | 1 |
| 1M***44 | Bolt; (3/8-16x2-1/4 In) | 2 |
| 1W***38 | Shaft As-Pump Drive; (8-Teeth) | 1 |
102-6845 Tank Gp-Engine Oil
| 00***44 | Elbow; (45-Deg) | 1 |
| 10***45 | Tank Group-Engine Oil | 1 |
| 11***11 | Hose As | 2 |
Operator Station
141-7883 Box As-Storage
| 14***83 | Box As-Storage | 1 |
| 4S***64 | Rivet; (On Front L.H. Of Seat Support) | 4 |
| 5P***37 | Seal 1.667 M(65.25 In.) | 0 |
178-9030 Box As-Storage
| 13***07 | Circuit Breaker; (15 Amp, 1 Pole) | 1 |
| 13***09 | Relay As; (Heater Control)(24 Vdc Pump Energize) | 1 |
| 13***15 | Kit-Mounting Foot | 4 |
177-8940 Box Gp-Control Panel
| 11***75 | Control Group-Emcp Electronic | 1 |
| 11***70 | Control Group-Emcp Electronic; -Generator Set Control + | 1 |
| 11***71 | Control Group-Emcp Electronic | 1 |
141-2858 Control Ar-Emcp Electronic
| 13***49 | Control Group-Alarm Module | 1 |
| 14***58 | Control Ar-Emcp Electronic | 1 |
| 9Y***76 | Film; (Annunciator)(Control Panel) | 1 |
9y-2907 Control Gp-Alarm Module
| 26***89 | Indicator As; (Fuel Pressure) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 5P***28 | Adapter-O-Ring; (1/8-27 Nptf Thd) | 1 |
130-3333 Module Gp-Alarm
| 13***24 | Module Group-Alarm | 1 |
| 13***26 | Film-Control Panel; (Custom Alarm Module Idents) | 1 |
| 13***28 | Film-Control Panel; (Custom Alarm Module) | 1 |
130-3332 Control Gp-Alarm Module
| 13***32 | Control Group-Alarm Module | 1 |
| 9Y***07 | Control Group-Alarm Module | 1 |
9y-2906 Control Gp-Alarm Module
| 15***78 | Bracket As | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 3 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 6 |
9w-3577 Module Gp-Alarm
| 14***90 | Screw-Wood | 3 |
| 15***78 | Bracket As | 1 |
| 9W***77 | Control Group-Alarm Module | 1 |
130-3349 Control Gp-Alarm Module
| 13***26 | Film-Control Panel; (Custom Alarm Module Idents) | 1 |
| 13***27 | Film-Control Panel; (Custom Alarm Module) | 1 |
| 13***32 | Control Group-Alarm Module | 1 |
7e-1234 Control Gp-Alarm Module
| 2D***35 | Locknut (Visor To Bracket) | 4 |
| 7E***34 | Control Group-Alarm Module | 1 |
| 8T***05 | Washer, Flat-Thin(1/4); W/O Freespool Qty Is 12 | 8 |
133-6350 Control Gp-Emcp Electronic
| 13***50 | Control Group-Emcp Electronic; -Generator Set Control | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
148-5368 Module Gp-Relay Driver
| 10***83 | Screw-Machine; (10-24x2.5-In) | 2 |
| 10***64 | Cover; (Synchronizing Lights Module) | 1 |
| 14***68 | Control Group-Emcp Electronic | 1 |
102-8619 Control Gp-Emcp Electronic
| 10***19 | Control Group-Emcp Electronic | 1 |
| 13***49 | Control Group-Alarm Module | 1 |
| 7C***30 | Film-Identification | 1 |
118-0175 Control Gp-Emcp Electronic
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***49 | Control Group-Alarm Module | 1 |
| 9Y***47 | Film-Identification; (Control Panel) | 1 |
101-0225 Control Gp-Emcp Electronic
| 10***25 | Control Group-Emcp Electronic | 1 |
| 13***49 | Control Group-Alarm Module | 1 |
| 17***90 | Wire; (18-Ga, White)(42.5-cm Ea) | 0 |
118-2071 Control Gp-Emcp Electronic
| 11***71 | Control Group-Emcp Electronic | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
118-2070 Control Gp-Emcp Electronic
| 11***70 | Control Group-Emcp Electronic; -Generator Set Control + | 1 |
| 17***90 | Wire; (18-Ga, White)(42.5-cm Ea) | 0 |
| 2W***80 | Boot-Switch | 2 |
103-6101 Control Gp-Engine Monitoring
| 10***01 | Control Group-Engine Monitoring | 1 |
| 13***29 | Film-Control Panel; (Alarm Module) | 1 |
| 13***49 | Control Group-Alarm Module | 1 |
149-8661 Control Gp-Engine Monitoring
| 10***22 | Housing As; (Transformer Box-Emcp Ii) | 1 |
| 10***03 | Channel As; (Transformer-Emcp Ii) | 1 |
| 10***16 | Seal-Interface | 1 |
146-0806 Door As-Access -Fuel
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 14***06 | Door As-Access; -Fuel | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
149-8841 Door Gp-Access
| 13***15 | Film-Control Panel; (Generator Set Control +)(Emcpii+) | 1 |
| 13***50 | Control Group-Electronic; (Relay Module)(Generator Set Control +) | 1 |
| 14***41 | Door Group-Access | 1 |
113-1204 Door Gp-Access -Switchgear Door
| 10***27 | Screw-Pan Head; (10-24x0.25-In) | 8 |
| 11***04 | Door Group-Access; -Switchgear Door-Switchgear Room | 1 |
| 15***65 | Kit-Connecting Plug; (8-Pin)(Electronic Control Channel) | 1 |
168-6426 Door Gp-Access -Switchgear Room
| 10***00 | Control Group-Electronic; (Relay Module) | 1 |
| 13***16 | Film-Information; (Control Panel)(Emcp Ii - Graphic/Text) | 1 |
| 16***26 | Door Group-Access; -Switchgear Room | 1 |
171-4917 Door Gp-Access -Air Vent
| 10***50 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 14***62 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
| 17***17 | Door Group-Access; -Air Vent | 1 |
109-3355 Fastener Gp-Rfi Filter
| 10***55 | Fastener Group-Rfi Filter | 1 |
230-4194 Fire Extinguisher Gp
| 14***27 | Handle-Door | 1 |
| 15***22 | Handle | 1 |
| 15***23 | Carrier | 1 |
102-6818 Fire Extinguisher Gp
| 10***18 | Fire Extinguisher Group | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 16 |
| 8T***05 | Washer, Flat-Thin(1/4); W/O Freespool Qty Is 12 | 16 |
6n-8878 Gauge Gp-Fuel Pressure
| 14***45 | Actuator As | 2 |
| 4M***25 | B. 5/16 N.C. X 1" | 16 |
| 6N***78 | Gauge Group-Fuel Pressure | 1 |
332-8866 Kit-Electronic Conversion -Generator Set Control +
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 11***04 | Door Group-Access; -Switchgear Door-Switchgear Room | 1 |
| 11***05 | Bracket As | 1 |
129-4018 Lamp Gp-Panel Illumination
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 11***04 | Door Group-Access; -Switchgear Door-Switchgear Room | 1 |
| 12***18 | Lamp Group-Panel Illumination | 1 |
4n-2328 Meter Gp-Service
| 16***60 | Door Group; (Vent) | 1 |
| 17***37 | Gasket | 1 |
| 17***18 | Screw; (No 10x5/8-In) | 12 |
131-1958 Module Gp-Alarm
| 12***30 | Film-Identification; (Caterpillar)(Emcpii Relay Driver Module) | 1 |
| 13***58 | Module Group-Alarm | 1 |
| 2D***63 | Bolt; (1/4-28x1.75-In) | 2 |
130-3325 Module Gp-Alarm
| 13***25 | Module Group-Alarm; (Custom) | 1 |
| 1P***23 | Kit-Meter Window Service; (Window) | 1 |
| 4M***03 | Packing,Preformed Hourmeter Mtg | 1 |
121-4716 Module Gp-Alarm
| 11***75 | Control Group-Emcp Electronic | 1 |
| 11***70 | Control Group-Emcp Electronic; -Generator Set Control + | 1 |
| 12***16 | Module Group-Alarm | 1 |
131-1956 Module Gp-Alarm
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 13***56 | Module Group-Alarm | 1 |
130-3324 Module Gp-Alarm
| 12***41 | Lamp-Base | 1 |
| 12***43 | Lamp-Lens; (Red) | 1 |
| 12***55 | Lamp-Led; (24-Volt, Red)(Emergency Stop) | 1 |
130-3350 Module Gp-Alarm
| 13***25 | Module Group-Alarm; (Custom) | 1 |
| 13***50 | Module Group-Alarm | 1 |
123-7450 Module Gp-Relay Driver
| 12***50 | Module Group-Relay Driver; Control Gp-Engine Monitoring | 2 |
| 6V***75 | Track-Relay; (34-cm) | 0 |
| 6V***87 | Screw-Pan Head; (10-24x1-In) | 2 |
106-5171 Module Gp-Synchronizing Lights
| 10***69 | Module Group-Synchronizing Lights | 1 |
| 10***71 | Module Group-Synchronizing Lights | 2 |
106-5169 Module Gp-Synchronizing Lights
| 10***64 | Cover; (Synchronizing Lights Module) | 1 |
| 10***69 | Module Group-Synchronizing Lights | 1 |
| 17***81 | Nut; (1/4-20-Thd) | 2 |
131-1970 Module Gp-Synchronizing Lights
| 13***70 | Module Group-Synchronizing Lights | 1 |
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
131-1969 Module Gp-Synchronizing Lights
| 10***69 | Module Group-Synchronizing Lights | 1 |
| 10***71 | Module Group-Synchronizing Lights | 1 |
| 13***69 | Module Group-Synchronizing Lights | 1 |
104-4704 Mounting Gp-Control Panel -Emcp Ii
| 10***04 | Mounting Group-Control Panel; -Emcp Ii | 1 |
| 1H***38 | Lockwasher, External Tooth (1/4); W/O Freespool Qty Is 6 | 4 |
| 6V***85 | Nut-Full (1/4-20 Thd); (1/4-20-Thd)(Full) | 4 |
7e-7078 Mounting Gp-Instrument Panel
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 5 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
| 6K***06 | Strap-Cable -Lines From Rotate Valve | 1 |
262-5314 Padlock Gp
| 06***88 | Locknut; (1-11-1/2-Thd) | 3 |
| 10***25 | Control Group-Emcp Electronic | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
177-8941 Panel Ar-Control
| 12***99 | Wrap-Spiral; (3/8-In Od)(307-cm) | 0 |
| 12***67 | Jumper-Terminal | 3 |
| 12***11 | Relay Group; -Fuel Level | 3 |
130-7237 Panel Ar-Control
| 12***68 | Circuit Breaker; (15 Amp, 1 Pole) | 2 |
| 13***37 | Panel Ar-Control | 1 |
| 13***07 | Circuit Breaker; (15 Amp, 1 Pole) | 1 |
146-9839 Panel Gp-Control
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 12***78 | Bracket | 1 |
| 14***39 | Panel Group-Control | 1 |
170-6481 Panel Gp-Control
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 12***26 | Relay Group; -Auxiliary | 1 |
| 17***81 | Panel Group-Control | 1 |
146-9838 Panel Gp-Control
| 11***23 | Block-Contact; (1-Pole)(Normally Open) | 5 |
| 11***24 | Block-Contact; (1-Pole)(Normally Closed) | 3 |
| 12***99 | Wrap-Spiral; (3/8-In Od)(307-cm) | 0 |
121-4712 Panel Gp-Electronic
| 12***12 | Panel Group-Electronic | 1 |
| 13***25 | Module Group-Alarm; (Custom) | 1 |
| 4P***60 | Washer; (Retaining Ring) | 6 |
131-1962 Panel Gp-Instrument
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 13***62 | Panel Group-Instrument | 1 |
| 4P***60 | Washer; (Retaining Ring) | 6 |
131-1961 Panel Gp-Instrument
| 13***61 | Panel Group-Instrument | 1 |
| 4P***60 | Washer; (Retaining Ring) | 6 |
| 4P***61 | Screw | 6 |
131-1960 Panel Gp-Instrument
| 13***25 | Module Group-Alarm; (Custom) | 1 |
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 13***60 | Panel Group-Instrument | 1 |
131-1965 Panel Gp-Instrument -Emcp Ii
| 10***72 | Seal; (Control) | 1 |
| 13***65 | Panel Group-Instrument; -Emcp Ii | 1 |
| 5L***80 | Washer; (0.490x0.875x0.050-In Thk) | 3 |
131-1963 Panel Gp-Instrument
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 13***50 | Module Group-Alarm | 1 |
| 13***63 | Panel Group-Instrument | 1 |
103-8975 Seal Gp-Enclosure
| 10***72 | Seal; (Control) | 1 |
| 10***75 | Seal Group-Enclosure | 1 |
| 5L***80 | Washer; (0.490x0.875x0.050-In Thk) | 3 |
121-4705 Seal Gp-Enclosure
| 12***05 | Seal Group-Enclosure | 1 |
Prime Package
210-5558 Box Gp-Storage
| 13***98 | Floorplate-Galvanized | 1 |
| 14***90 | Screw-Wood | 12 |
| 21***58 | Box Group-Storage | 1 |
149-6400 Floorplate Gp
| 14***00 | Floorplate Group | 1 |
9y-1392 Jack Gp-Height Adjuster
| 9Y***92 | Jack Group-Height Adjuster | 1 |
151-5714 Ladder Gp
| 15***14 | Ladder Group | 1 |
| 22***97 | Ladder As | 1 |
| 22***99 | Handrail As | 1 |
224-1196 Ladder Gp
| 22***96 | Ladder Group | 1 |
| 7X***86 | Deflector | 2 |
9y-1386 Undercarriage Ar
| 7X***86 | Deflector | 2 |
| 9Y***86 | Undercarriage Ar | 1 |
137-5055 Undercarriage Ar
| 13***55 | Undercarriage Ar | 1 |
136-1147 Undercarriage Ar
| 13***47 | Undercarriage Ar | 1 |
| 7X***86 | Deflector | 2 |
9y-1387 Undercarriage Ar
| 7X***86 | Deflector | 2 |
| 9Y***87 | Undercarriage Ar | 1 |
9y-1385 Undercarriage Ar
| 7X***86 | Deflector | 2 |
| 9Y***85 | Undercarriage Ar | 1 |
Service Equipment And Supplies
4w-8145 Chart-Circuit Breaker
| 4W***45 | Chart-Circuit Breaker | 1 |
129-4053 Chart-Control Panel
| 12***53 | Chart-Control Panel | 1 |
4w-8000 Chart-Control Panel
| 4W***00 | Chart-Control Panel | 1 |
7e-4300 Chart-Instrument Panel
| 11***88 | Film; (Identification) (Fuel Filter) (On Secondary Fuel Filter) | 2 |
| 11***52 | Plate & Film Group; -Engine Information | 1 |
| 3N***69 | Tag-Instruction; (Engine Prestart)(English And Spanish) | 1 |
6l-4502 Chart-Plate & Film
| 20***19 | Film-Identification; (Caterpillar) | 1 |
| 20***23 | Film; (Www.Cat.Com) | 2 |
| 20***25 | Film-Identification; (Electric Power) | 2 |
309-5969 Film Gp
| 12***27 | Bar-Bus | 1 |
| 12***28 | Insulator | 1 |
| 30***69 | Film Group | 1 |
224-6549 Film Gp -Power Module
| 20***46 | Film-Information; (Phone, Internet Contact) | 2 |
| 22***49 | Film Group; -Power Module | 1 |
| 29***46 | Film-Identification; (Cat) | 1 |
201-7730 Film Gp
| 08***17 | Film-Instruction; (Manuals Inside) | 1 |
| 10***08 | Film-Caution; (High Trailer) | 3 |
| 10***69 | Film-Information | 2 |
4p-1799 Kit-Bus Bar
| 4P***99 | Kit-Bus Bar | 1 |
4p-3317 Kit-Installation -Exciter
| 11***10 | Regulator As-Voltage | 1 |
| 15***20 | Regulator As-Voltage | 1 |
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
161-0080 Kit-Parts
| 16***80 | Kit-Parts | 1 |
| 9Y***68 | Kit-Rfi Filter | 1 |
7e-5034 Kit-Rfi Filter
| 11***98 | Lead As | 1 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 4D***66 | Strip (Terminal) | 1 |
4p-1788 Kit-Space Heater -Generator
| 4P***88 | Kit-Space Heater; -Generator | 1 |
115-5852 Plate & Film Gp -Engine Information
| 11***52 | Plate & Film Group; -Engine Information | 1 |
| 4B***58 | Screw (Identification Plate) Mounting | 4 |
205-5940 Plate & Film Gp
| 20***40 | Plate & Film Group | 1 |
PM3412 serial number reference
The PIN/serial plate on a PM3412 power module is riveted to the module skid or generator-end frame, usually near the control panel or engine flywheel housing, and duplicated on an ID tag inside the control cabinet. The serial reads as a 3-character prefix followed by a sequential unit number (for example CAJ00123). The prefix identifies the build series or parts-manual coverage for that unit; the digits are the running unit count within that series.
| Prefix | Identifies | Notes |
|---|---|---|
| 5FL | PM3412 Power Module, 3412C engine | Base prefix for the PM3412 power module built on the 3412C diesel, unit 00001-up. Reads back to the PM3412 power module on Caterpillar's own serial-number-prefix identification chart and repeats across the module's parts-manual listings tied to the 3412C engine arrangement. |
| CAJ | PM3412 Power Module | Second base prefix for the PM3412 power module, listed alongside 5FL on Caterpillar's prefix identification chart and repeated across parts-catalog listings for the module. Also covers a 3000-ampere fixed-mount breaker bus bar group for switchgear without a rear extension, starting at unit 1-up. |
| 6EJ | PM3412 Power Module - confirm with dealer | Covers PM3412 attachment groups (circuit breaker mounting, EMCP electronic control, coupling fastener) starting at unit 1-up, always paired with 7AJ. Listed in the module's own parts manual but absent from the general prefix identification chart, so treat as a running-production or attachment-specific block and confirm exact coverage with a dealer. |
| 7AJ | PM3412 Power Module - confirm with dealer | Appears in the same PM3412 attachment groups as 6EJ (circuit breaker mounting, EMCP control, coupling fastener), always cited together with 6EJ starting at unit 1-up. Listed in the module's parts manual but not on the general prefix chart - confirm with dealer. |
| BLG | PM3412 Power Module - confirm with dealer | Covers a 3000-ampere fixed-mount breaker bus bar group for switchgear without a rear extension, listed as BLG175-up paired with CAJ1-up in the module's own parts manual. Narrow attachment-specific range, not on the general prefix chart - confirm with dealer before relying on it. |
Frequently asked questions
What engine powers the Caterpillar PM3412?
The PM3412 power module is built around the Caterpillar 3412 or 3412C TA V-12 diesel engine, a 27 L (1,650 cu in) turbocharged and aftercooled unit confirmed against the serial prefixes tied to this power module's nameplate.
What does the PM3412 weigh?
The bare generator-set engine and alternator assembly on this platform weighs roughly 5.4 to 5.9 metric tons (about 12,000 to 13,000 lb) dry; a fully packaged Power Module with mounting skid, fuel sub-base, and enclosure weighs more, and the exact packaged weight varies by configuration.
What replaced the PM3412?
No confirmed successor model has been documented for the PM3412 in Caterpillar's PM power-module lineup. Treat any specific successor claim as unverified and confirm current equivalents with a Cat dealer.
What PM3412 owners discuss
How reliable is the 3412/3412C engine inside the PM3412 power module, and what kind of service life should an owner expect?
The V12 3412 family has a strong reputation for long-term durability in genset duty. Properly maintained units commonly run toward 10,000 hours before a major overhaul, and the mechanical (non-electronic-common-rail) architecture on early units makes field repair straightforward. Hour count alone is a poor predictor of remaining life on a power module though - duty cycle matters more. A unit that sat at low load (lightly loaded standby or partial rental duty) for most of its hours tends to wear injectors and rings faster than one run near rated load, due to incomplete combustion and cylinder glazing at light load. Ask about load history, not just total hours, when judging condition.
What HEUI fuel system quirks show up on 3412/3412C engines in these power modules?
Hard starting after the unit sits idle for a week or more (especially in cooler weather) is a recurring complaint, traced to check valves in the injector oil-return circuit bleeding down and slowing initial oil pressure buildup to the injectors. Carbon buildup in the injector sleeves is also common on units with irregular run hours - this can cause a new injector to hang up or crack on installation if the sleeve isn't cleaned first. Misfire, laboring, or smoke tied to one specific cylinder usually points to a single failed injector or its driver circuit rather than a fuel-supply problem. Injector and injector-sleeve work affects combustion and emissions - have your dealer verify injector condition and sleeve cleanliness before returning the unit to service.
What generator-end (alternator) issues are typical on skid/trailer power modules like the PM3412 after years of rental or standby use?
Brush and slip-ring wear is the most common maintenance item on brushed generator ends - carbon dust from brush wear accumulates on the rings and needs periodic cleaning, and worn brushes eventually cause intermittent excitation or voltage regulation faults. Main bearing wear is the other recurring issue; if the bearing goes long enough undetected, the rotor can rub the stator, causing localized overheating and stator winding damage. Listen for new bearing noise or vibration at speed and check for discoloration or a burnt smell around the stator housing on inspection - these point to bearing failure in progress. Bearing and rotor/stator work is safety- and performance-critical - have your dealer verify generator-end condition before continued service.
What do owners commonly run into with the EMCP control panel on these units?
Nuisance alarms and sensor-related fault codes are the most reported EMCP complaint - a flaky coolant temperature, oil pressure, or speed/frequency sensor (or a corroded connector) can trip a shutdown or warning even when the engine itself is fine, so a fault code should prompt a sensor and wiring check before assuming an engine problem. Panel generation matters for parts and diagnostic support: older EMCP II/3 panels are more basic and increasingly hard to source spares for, while EMCP 4 panels (4.2/4.3/4.4) add a larger graphical display and remote annunciator/HMI support, which rental and standby operators generally prefer for remote monitoring. When buying or servicing a used unit, confirm which EMCP generation is installed, since programming, wiring, and diagnostic tools differ between them.
How does the cooling system on a trailer/skid-mounted PM3412 behave under sustained load, and what causes overheating complaints?
These units rely on an engine-driven radiator inside a sound-attenuated enclosure, so cooling performance depends heavily on enclosure airflow, not just radiator condition. Undersized or restricted inlet/outlet louvers are a common root cause of overheating in the field - inlet ducting needs to be noticeably larger than the outlet, and any added louvers or screens reduce effective airflow and may need enlarging. Sustained heavy load in hot ambient or dusty environments (common on rental and oilfield sites) accelerates radiator fin fouling and belt/hose wear, so a unit with a documented history in a hot or dusty application deserves a closer cooling-system inspection than one that ran mostly indoors or in mild climates.
Do these engines show turbo or exhaust manifold issues under prolonged full-load generator duty?
Yes - turbo overheating and exhaust manifold discoloration under sustained heavy load are recurring complaints, generally traced to intake or exhaust restriction (dirty air filters, collapsed piping, or a partially fouled turbo) rather than a turbo defect itself. Because a generator set often runs at a fixed, sustained load rather than the varying load of mobile equipment, any airflow restriction shows up faster as heat than it would on a machine that cycles load constantly. Persistent high exhaust temperature or visible manifold discoloration warrants a full air-intake and exhaust-restriction check before condemning the turbocharger. Turbo and exhaust system faults affect engine safety and emissions compliance - have your dealer verify before further operation.
What should a buyer check when looking at a used Cat PM3412 power module?
Confirm rated kW/kVA, voltage, phase, and frequency configuration match the intended use, since 3412-based power modules were built in multiple output and voltage configurations. Get the hour meter reading and cross-check it against visible wear on the engine, generator end, and enclosure - a low hour count with heavy wear, or a high hour count with light wear, both deserve an explanation. Ask for maintenance records and, ideally, a recent load-bank test report; a documented load-bank test is the single best evidence the unit will perform at rated load rather than just at no-load idle. Note which EMCP control panel generation is fitted, since this affects parts availability and remote monitoring options. Physically inspect the radiator core and enclosure louvers for fouling or damage, check for fuel, oil, or coolant leaks around the engine, and ask whether the unit was used for standby (light, intermittent duty) or continuous rental/prime power, since duty cycle drives wear on injectors, rings, and the generator-end bearing. On any unit without a recent load-bank test, budget for one - have your dealer perform it before you rely on the machine for real load.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific PM3412 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.