Caterpillarchallenger
Caterpillar MT835
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar Challenger MT835 is a rubber-belted, track-type row-crop tractor built for high-horsepower tillage, seeding, and grain-cart work. This original generation runs a Caterpillar C12 11.9L turbocharged diesel rated at a gross 340 hp (253 kW), paired with a 16-speed powershift transmission and Caterpillar's rubber Mobil-trac belt undercarriage in place of steel tracks or wheels. Standard fuel capacity is 1154.4 L (305 US gal), with a 1249.0 L (330 US gal) tank offered as an option, and the closed-center, load-sensing hydraulic system holds roughly 264.9 L (70 US gal) at up to 200 bar (2900 psi). Operating weight lands around 18,140 kg (40,000 lb), varying with ballast and configuration. Built from 2002 to 2004 under BAM-prefix serial numbers, the MT835 was among the first Challenger track tractors produced after AGCO acquired Caterpillar's Challenger ag-tractor business in 2002, effectively continuing the high-horsepower, C12-powered role Cat's own DeKalb-built Challenger 75-series tractors had filled, with Caterpillar staying on as long-term supplier of the engine, drivetrain, and Mobil-trac belt system. It was offered with a cab and standard air conditioning, and in more than one belt-width configuration for different row-crop and tillage setups.
AGCO retired the original C12-powered MT835 in 2005 in favor of the MT835B, which reuses the same model number but switches to a larger Caterpillar C15 ACERT 15.2L engine rated near 350 hp and updated electronics. A further MT835C generation followed from 2009 to 2013 with a 410 hp C15 ACERT engine and its own control system. Those later tractors share the MT835 badge but not the engine, fuel system, or electronics of the 2002-2004 original, so parts and service data do not cross over cleanly between generations. For buyers today, the original C12 MT835 sits in the used market as a comparatively simple, pre-emissions-era track tractor with no exhaust aftertreatment to maintain, mechanically more straightforward than the ACERT-generation machines that followed it. Its age puts undercarriage belts, midwheels, and hydraulic components among the parts most commonly sourced for these tractors now, and confirming the BAM serial prefix is the fastest way to verify a listing is the original C12 tractor rather than a later B- or C-series machine wearing the same MT835 name.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar MT835 specifications
Engine
| Engine | Caterpillar C12 turbocharged diesel, 11.9 L (729 cu in), 6-cylinder, bore x stroke 130 x 150 mm (5.118 x 5.906 in), compression ratio 16.0:1 |
| Power | Gross 254 kW (340 hp) at 2100 rpm. PTO claimed 205 kW (275 hp); PTO as tested 267 kW (357.9 hp), per Nebraska/OECD tractor test data |
| Emissions tier | Not documented in available spec sources for this build era - verify with your dealer |
Weights
| Shipping/operating weight | 18,144 kg (40,000 lb) base shipping weight; up to 22,680 kg (50,000 lb) ballasted; maximum rated gross machine weight 27,216 kg (60,000 lb) |
| Ground pressure | Not published in available spec sheets for this model - verify with your dealer |
Dimensions
| Overall length | 675 cm (265.9 in) |
| Overall width | 357-360 cm (140.9-142.1 in), varies by track width fitted |
| Height to cab roof | 350 cm (138.1 in) to cab roof; 352 cm (138.7 in) to exhaust stack |
| Wheelbase | 299 cm (118 in) |
| Ground clearance | 47 cm (18.7 in) |
| Track gauge (center-to-center) | 228-325 cm (90-128 in) adjustable |
| Track width | 46 cm (18 in) standard; wider belts offered as an option up to 91 cm (36 in) |
Performance
| Transmission | 16 forward / 4 reverse full powershift |
| Rear PTO | 1000 rpm, independent rear PTO |
| Steering | Hydrostatic power steering |
| Drawbar power (as tested) | 196 kW (263.3 hp), per Nebraska/OECD tractor test data |
| 3-point hitch | Category III/IVN, rated lift capacity 8845 kg (19,500 lb) |
Service capacities (summary)
| Fuel tank | 1154.4 L (305 gal) standard; 1249.0 L (330 gal) optional larger tank |
| Hydraulic system | Closed-center, load-sensing/pressure-flow-compensated system; reservoir capacity 264.9 L (70 gal) |
| Hydraulic pump flow | 165 L/min (43.5 gpm) standard, 223 L/min (59 gpm) optional high-flow pump, system relief pressure 200 bar (2900 psi) |
| Engine oil capacity | Not documented in available spec sources for this model - verify with dealer or the Cat C12 service manual |
| Cooling system capacity | Not documented in available spec sources for this model - verify with dealer or shop manual |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
MT835 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase, with oil filter (Cat C12, 11.9 L turbocharged diesel) | Approx. 34-38 L (9-10 US gal) engine lube system total; exact ag-chassis sump figure not separately published for this model — confirm against dealer service chart before draining | Cat DEO (Diesel Engine Oil), SAE 15W-40 for above-freezing climates; Cat DEO SYN or 10W-30 multigrade for cold starts below 0°C (32°F) |
| Cooling system | Not published in available documentation for this model — total system volume (block, radiator, degas tank) not confirmed; verify with dealer or OMM cooling section | Cat ELC (Extended Life Coolant) or Cat DEAC antifreeze/coolant, pre-mixed 50/50 water-glycol, year-round formulation |
| Fuel tank | 1154.4 L (305 US gal) standard tank; 1249.0 L (330 US gal) optional large tank | No. 2-D diesel fuel meeting Cat diesel fuel specification |
| Transmission / powertrain compartment (16-speed powershift, hydrostatic steer) | Not separately published. Transmission/drivetrain lubrication draws from its own reservoir apart from the implement-hydraulic tank; no liter figure confirmed in available excerpts | Cat TDTO (Transmission/Drive Train Oil), multi-viscosity, standard factory-fill for powershift and final-drive compartments of this generation |
| Final drives / track drive sprockets, each side | Not published in available excerpts. Each final-drive and bogie-wheel housing is individually oil-filled per the undercarriage lubrication chart; no per-side figure confirmed | Cat TDTO, same drive-train oil spec used in the transmission compartment |
| Hydraulic system (implement hydraulics) and tank | 264.9 L (70 US gal) total system capacity. System pressure 200 bar (2900 psi). Standard pump flow 164.6 L/min (43.5 gpm); optional high-flow pump 223.3 L/min (59 gpm) | Cat HYDO (Hydraulic Oil), multi-viscosity formulation for wide ambient temperature range; some circuits may share Cat TDTO where the OMM specifies a common drivetrain/hydraulic fluid |
| Grease points (chassis, pivots, track rollers) — spec only | N/A — serviced per lubrication interval chart, no reservoir capacity | Cat Multipurpose Grease (NLGI Grade 2 lithium-complex EP) or Cat Advanced 3Moly Grease for high-load undercarriage points |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar MT835 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 3,000 h |
|
| Every 6,000 h |
|
Servicing the MT835 beyond the schedule
Predictive Maintenance & Fluid Analysis
Run oil sampling on the C12 engine, 16-speed powershift, and final drives at every scheduled interval. This non-ACERT C12 has no exhaust aftertreatment to mask early wear, so oil trends give the clearest early warning of injector, turbocharger, or clutch-pack problems. Track coolant condition and fuel-filter restriction closely, since these tractors are now decades old and cooling and fuel systems accumulate scale and varnish over time. Log Mobil-trac belt tension and midwheel temperature during hot-weather work; uneven wear patterns predict belt or roller failure before it strands the tractor mid-field.
Corrective & Common Repairs
On a tractor this age, expect the C12's fuel injectors, turbocharger, and water pump to be the highest-wear failure points; smoke, power loss, or coolant weep at these components is common at high hours. On the drivetrain, powershift clutch packs and steering-brake linkages wear under heavy tillage duty and show up as slipping shifts or drift under load. Undercarriage repairs center on the Mobil-trac belt, midwheels, and front idler, where belt cracking, exposed steel cable, and midwheel play are the most frequently reported field complaints on this generation.
Overhaul & Rebuild Points
A full C12 inframe overhaul is the major rebuild point on a high-hour MT835, usually triggered by falling compression or rising oil consumption rather than a fixed hour mark. The 16-speed powershift and final drives are the next-largest rebuild items, since clutch packs and planetary gearing see constant load reversals during track-tractor tillage work. On the chassis side, complete Mobil-trac belt, midwheel, and idler replacement is normally done as a set to keep the undercarriage tracking straight, rather than piecemeal, once wear shows through the belt's internal steel-cable layers.
Seasonal & Environment Servicing
Ahead of planting or harvest, recheck Mobil-trac belt tension and alignment, since temperature swings shift rubber belt tension more than a steel track. In cold climates, run the correct oil viscosity for the C12, confirm glow/starting-aid function before cold starts, and set coolant freeze protection to factory dilution rather than guessing. In dusty tillage or harvest conditions, service the primary and secondary engine air filters more often than the standard interval and inspect the cab pressurizer filter, since a plugged filter is a common reported cause of power loss on these tractors.
MT835 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1R-0762 | Filter As-Fuel | Fuel system service | Check fitment → |
| 161-1705 | Sensor As-Pressure | Lubrication service | Check fitment → |
| 111-2645 | Valve-Pump Bypass | Lubrication service | Check fitment → |
| 1R-0716 | Filter As-Engine Oil | Lubrication service | Check fitment → |
| 9S-8752 | Nut-Full | Scheduled service item | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
MT835 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| E100 | Engine oil pressure fault | Oil pressure sensor reading out of range, or genuine low pressure from low oil level, worn pump, or a restricted pickup screen | Shut the engine down, check oil level and top off with the correct grade, look for leaks; if the level is correct suspect the sensor or wiring before restarting |
| E102 | Turbo boost / intake manifold pressure fault | Restricted or dirty air filter, a collapsed or leaking charge-air hose, or a failing turbocharger | Inspect the air filter element and intake piping for restriction or leaks, clean or replace the filter, reseat hose clamps, then clear the code and recheck under load |
| E107 | Air filter restriction (intake air pressure) fault | Air filter element loaded with dust or debris, or a collapsed intake hose | Service or replace the air filter element, check the restriction indicator, and inspect the intake ducting for damage |
| E110 | Engine coolant temperature fault (overheat or sensor fault) | Low coolant level, plugged radiator fins or screens, a weak fan drive, or a failed coolant temperature sensor | Let the engine cool, check coolant level and mix, clean the radiator and screens of debris, and verify fan operation before returning to service |
| E94 | Fuel filter / fuel pressure restriction fault | Loaded fuel filter element, water or debris in the fuel, or a weak lift/primer pump | Check fuel level, drain the fuel/water separator, replace the fuel filter, and check the primer pump fuse before further diagnosis |
| E97 | Water detected in fuel | Condensation or contaminated fuel collecting in the water separator bowl | Drain the fuel/water separator, check the fuel supply source for contamination, and replace the fuel filter if water keeps returning |
| E168 | Battery / charging system voltage fault (high or low) | Loose or corroded battery terminals, a failing alternator or regulator, or a weak battery | Check and clean battery terminal connections, test charging voltage at idle and at rated rpm, and load-test the battery |
| D149 / D150 | CAN data-bus communication signal fault between the cab display and machine control modules | Intermittent harness connection, corroded connector pins, or a control module dropping off the data link | Cycle the key off for several seconds to reset the bus, check main harness connectors for corrosion, and check module grounds before deeper diagnosis |
| T4128 | Transmission control unit fault | Internal TCU fault or lost communication with a transmission speed sensor or shift solenoid, dropping the gearbox into a protective mode | Note the conditions when the fault set, cycle the key to see if it clears, and have the transmission control unit and its wiring checked if the fault returns or the transmission stays in protection mode |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
MT835 attachments & work tools
Drawbar systems
Standard wide-swinging roller drawbar (Category 5) swings about ±32° and carries roughly 4990-6804 kg (11,000-15,000 lb) vertical load depending on source. A free-swinging drawbar pairing with the 3-point hitch swings about ±28°. An optional hydraulic-controlled drawbar lets the operator position or dampen it from the cab and carries up to about 6804 kg (15,000 lb).
Three-point hitch
Optional rear 3-point hitch is offered in standard and high-capacity form; standard lift is around 6804 kg (15,000 lb) and the high-capacity version around 9072 kg (20,000 lb), with one steerable version cited near 8845 kg (19,500 lb) - capacity varies by configuration/series. The steerable design ties into the tractor's steering to tighten headland turns under draft load.
PTO
Optional independent rear PTO runs at 1000 rpm on a 44 mm (1.75 in) shaft. It is engaged and monitored from the same cab display used for the transmission, hydraulics, and hitch.
Hydraulic remote kit
Closed-center, load-sensing hydraulic system with roughly 265 L (70 US gal) reservoir capacity. Standard single-pump flow is about 165 L/min (43.5 gpm) feeding 4 rear remote valves; an optional higher-flow pump raises flow to about 223 L/min (59 gpm) and adds up to 6 remote valves total. Quick-hitch couplers come standard for fast implement hookup.
Track/undercarriage
Rubber Mobil-Trac belts are the standard undercarriage for this size class, with 457 mm (18 in) width the common factory fit. Wider and narrower belt widths are offered across the model family for different soil and flotation needs; replacement belts for this platform are sourced through the rubber-track aftermarket.
Ballast and weight kits
Front-mounted and chassis ballast weight kits are available to rebalance the tractor, improve headland handling, and increase drawbar pull with heavier pulled implements.
Factory configuration options
Cab comes standard with air conditioning, heat, and ROPS protection. Factory upgrades for heavier draft work include a larger fuel tank (about 1249 L / 330 gal versus the standard 1154 L / 305 gal) and the higher-flow hydraulic pump noted above.
All MT835 assemblies by section
Every catalogued assembly group for the Caterpillar MT835. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
205-1231 Elbow Gp-Air Inlet
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 10***25 | Gasket; (Air Inlet Manifold)(Intake Manifold Inlet) | 1 |
| 10***03 | Elbow; (Air Inlet) | 1 |
205-1232 Elbow Gp-Air Inlet
| 10***25 | Gasket; (Air Inlet Manifold)(Intake Manifold Inlet) | 1 |
| 10***03 | Elbow; (Air Inlet) | 1 |
| 20***32 | Elbow Group-Air Inlet | 1 |
114-1904 Lines Gp-Air
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 11***04 | Lines Group-Air | 1 |
| 5H***04 | Packing,Preformed Elbow Part Of Kit P/N 5r***26 | 2 |
126-0076 Lines Gp-Air -Turbocharger Outlet
| 12***73 | Elbow | 1 |
| 12***76 | Lines Group-Air; -Turbocharger Outlet | 1 |
| 12***29 | Clamp; (V-Band) | 1 |
135-6552 Manifold Gp-Exhaust
| 10***54 | Manifold-Exhaust; (Center) | 1 |
| 10***08 | Manifold-Exhaust; (End)(End) | 2 |
| 10***92 | Stud-Taperlock; (3/8-16x3.93in) | 11 |
117-2688 Manifold Gp-Exhaust
| 10***13 | Gasket | 6 |
| 11***89 | Manifold-Exhaust; (Center) | 1 |
| 11***15 | Stud-Taperlock; (M10x85-mm Oal) | 12 |
116-5405 Manifold Gp-Inlet
| 11***05 | Manifold Group-Inlet | 1 |
| 11***06 | Manifold; (Inlet) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
191-5108 Turbocharger Gp
| 11***87 | Bolt; (M6x0.04x10.4-mm)(6mm X 0.04 Thd) | 1 |
| 12***53 | Clamp As; (Turbine) | 1 |
| 16***58 | Clip-Hose | 1 |
193-3931 Turbocharger Gp
| 19***08 | Turbocharger Group | 1 |
| 19***31 | Turbocharger Group | 1 |
| 1S***95 | Gasket-Turbocharger To Manifold; Gasket Turbocharger To Manifold | 1 |
192-3032 Turbocharger Gp
| 11***87 | Bolt; (M6x0.04x10.4-mm)(6mm X 0.04 Thd) | 1 |
| 13***75 | Clamp As; (Service Repair) | 1 |
| 16***58 | Clip-Hose | 1 |
191-2248 Turbocharger Gp
| 19***48 | Turbocharger Group | 1 |
| 19***32 | Turbocharger Group | 1 |
| 1S***95 | Gasket-Turbocharger To Manifold; Gasket Turbocharger To Manifold | 1 |
Basic Engine
133-9907 Adapter Gp-Pump Drive
| 13***06 | Adapter | 1 |
| 13***07 | Adapter Group-Pump Drive; -Remote | 1 |
| 1B***67 | Ball Bearing | 2 |
122-1248 Base Gp-Valve Cover & Inj Harn
| 10***18 | Clip | 3 |
| 10***19 | Clip | 3 |
| 10***34 | Kit-Receptacle; (12-Pin)(Valve Cover & Inj Harness) | 1 |
138-2546 Bracket Gp-Support
| 13***46 | Bracket Group-Support; -Refrigerant Compressor | 1 |
| 16***80 | Bracket | 1 |
| 6V***22 | Bolt (M10x1.50x35mm) | 2 |
171-3062 Camshaft Gp
| 11***59 | Cover | 1 |
| 12***11 | Journal | 1 |
| 13***68 | Gasket; (Camshaft Cover) | 1 |
185-9699 Camshaft Gp
| 10***89 | Cover | 1 |
| 11***36 | Screw-Flat Head; (5/16-18x0.875-In) | 3 |
| 18***99 | Camshaft Group; (Single) | 1 |
212-9551 Cover Gp-Cylinder Block
| 06***55 | Seal-O-Ring (Id=47.22mm) | 2 |
| 21***51 | Cover Group-Cylinder Block | 1 |
| 6V***17 | Bolt; (M8x1.25x20-mm)(At Location Y) | 4 |
107-6736 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 4N***99 | Gasket; (Oil Drain) | 1 |
115-2985 Cover Gp-Cylinder Block
| 11***85 | Cover Group-Cylinder Block | 1 |
| 4P***87 | Cover | 1 |
| 6V***50 | Seal-O-Ring (Id=39.34mm) | 1 |
107-6737 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 10***37 | Cover Group-Cylinder Block; -Remote | 1 |
| 4N***99 | Gasket; (Oil Drain) | 1 |
192-2042 Cover Gp-Engine
| 12***81 | Seal-Integral; (Air Compressor Mounting) | 1 |
| 14***14 | Cover | 1 |
| 16***87 | Hose-Fumes Disposal | 1 |
235-8781 Cover Gp-Front Housing
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 10***32 | Gasket | 1 |
| 18***09 | Plug As; (High Temperature) | 1 |
209-6669 Cover Gp-Front Housing
| 12***81 | Seal-Integral; (Air Compressor Mounting) | 1 |
| 14***14 | Cover | 1 |
| 20***69 | Cover Group-Front Housing; (Air Compressor) | 1 |
159-6159 Cover Gp-Front Housing
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 2 |
| 15***59 | Cover Group-Front Housing | 1 |
| 16***71 | Seal | 1 |
150-3135 Cover Gp-Valve Mechanism
| 14***78 | Grommet | 1 |
| 15***57 | Cover-Valve Mech | 1 |
| 15***35 | Cover Group-Valve Mechanism | 1 |
187-1326 Cover Gp-Valve Mechanism
| 14***78 | Grommet | 1 |
| 18***25 | Cover As-Valve | 1 |
| 18***26 | Cover Group-Valve Mechanism | 1 |
187-3316 Cover Gp-Valve Mechanism
| 15***41 | Cover Group-Valve Mechanism | 2 |
| 15***43 | Cover Group-Valve Mechanism | 1 |
| 18***16 | Cover Group-Valve Mechanism | 1 |
159-9343 Cover Gp-Valve Mechanism
| 14***78 | Grommet | 1 |
| 15***43 | Cover Group-Valve Mechanism | 1 |
| 17***39 | Cover As-Valve; (Breather) | 1 |
150-3141 Cover Gp-Valve Mechanism
| 14***76 | Cover-Valve Mechanism | 1 |
| 14***78 | Grommet | 1 |
| 15***41 | Cover Group-Valve Mechanism | 1 |
345-9238 Cover Gp-Valve Mechanism
| 15***35 | Cover Group-Valve Mechanism | 2 |
| 18***26 | Cover Group-Valve Mechanism | 1 |
| 34***38 | Cover Group-Valve Mechanism | 1 |
160-3913 Crankshaft Gp
| 15***32 | Crankshaft As | 1 |
| 16***13 | Crankshaft Group | 1 |
| 16***20 | Gear-Crankshaft; (80-Teeth) | 1 |
160-3912 Crankshaft Gp
| 16***99 | Crankshaft As | 1 |
| 16***12 | Crankshaft Group | 1 |
| 16***20 | Gear-Crankshaft; (80-Teeth) | 1 |
132-3212 Crankshaft Gp
| 12***82 | Bearing-Main; (0.51-mm Us)(.51mm U.S.) | 0 |
| 12***83 | Bearing-Main; (0.76-mm Us)(.76mm U.S.) | 0 |
| 12***84 | Bearing-Main; (0.51-mm Os)(.51mm O.S.) | 0 |
204-3449 Cylinder Block As
| 10***60 | Seal; (Liner) | 6 |
| 16***63 | Shim-Liner; -Cylinder | 0 |
| 16***64 | Shim-Liner; -Cylinder | 0 |
301-3016 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 13***17 | Seal D-Ring | 6 |
| 13***81 | Liner-Cylinder Block | 6 |
200-2054 Cylinder Block As
| 11***66 | Cap; (Bearing) | 7 |
| 17***54 | Bolt-Hex Head; (M16x160mm) | 14 |
| 20***54 | Cylinder Block As | 1 |
155-0741 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 13***17 | Seal D-Ring | 6 |
| 13***81 | Liner-Cylinder Block | 6 |
155-0056 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 14***17 | Seal-O-Ring; (140.20mm Id) | 6 |
| 14***72 | Seal-Liner; (Coolant) | 6 |
267-4632 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 14***17 | Seal-O-Ring; (140.20mm Id) | 6 |
| 14***72 | Seal-Liner; (Coolant) | 6 |
234-9709 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 13***17 | Seal D-Ring | 6 |
| 13***81 | Liner-Cylinder Block | 6 |
267-4631 Cylinder Block As
| 16***81 | Cap-Crankshaft Bearing | 7 |
| 16***83 | Bolt; (7/8-14x7.5-In) | 14 |
| 26***31 | Cylinder Block As | 1 |
115-2983 Cylinder Block Gp
| 11***83 | Cylinder Block Group | 1 |
| 1N***99 | Plug-O-Ring; (Straight Thread) | 2 |
| 20***49 | Cylinder Block As | 1 |
234-5998 Cylinder Block Gp
| 10***99 | Plug | 2 |
| 14***29 | Seal; (Drainback) | 1 |
| 1S***40 | Dowel; (30.23 mm X 9.37 mm) | 1 |
234-5997 Cylinder Block Gp
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 14***17 | Seal-O-Ring; (140.20mm Id) | 6 |
| 14***72 | Seal-Liner; (Coolant) | 6 |
155-0740 Cylinder Block Gp
| 10***99 | Plug | 2 |
| 11***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 14***29 | Seal; (Drainback) | 1 |
155-0057 Cylinder Block Gp
| 10***99 | Plug | 2 |
| 11***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 14***29 | Seal; (Drainback) | 1 |
234-9702 Cylinder Block Gp
| 10***99 | Plug | 2 |
| 14***29 | Seal; (Drainback) | 1 |
| 1S***40 | Dowel; (30.23 mm X 9.37 mm) | 1 |
223-7263 Cylinder Head As
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
243-6741 Cylinder Head As
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
243-0943 Cylinder Head As
| 15***82 | Insert-Valve Seat; (Exhaust)(Standard) | 12 |
| 16***42 | Insert-Valve Seat; (0.76-mm Os Od, Exhaust)(Standard) | 0 |
| 16***43 | Insert-Valve Seat; (0.76-mm Os Od, Inlet) | 0 |
281-1640 Cylinder Head As
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
179-9459 Cylinder Head As
| 11***02 | Sleeve; (Injector) | 6 |
| 13***06 | Insert-Valve Seat; (Inlet)(Standard) | 12 |
| 14***52 | Insert-Valve Seat; (0.508-mm Os Od)(0.508-mm Os Od) | 12 |
148-2149 Cylinder Head Gp
| 10***50 | Guide-Valve; (Standard) | 24 |
| 13***29 | Valve; (Exhaust) | 12 |
| 14***49 | Cylinder Head Group | 1 |
234-9185 Cylinder Head Gp
| 10***73 | Fastener Group-Cylinder Head; (Marked X) | 10 |
| 12***54 | Bolt-12 Point Head; (3/4-16x8.5-In) | 1 |
| 12***55 | Bolt-12 Point Head; (3/4-16x7.638-In) | 1 |
191-8423 Cylinder Head Gp
| 12***54 | Bolt-12 Point Head; (3/4-16x8.5-In) | 10 |
| 12***55 | Bolt-12 Point Head; (3/4-16x7.638-In) | 16 |
| 18***96 | Cylinder Head Group | 1 |
183-5296 Cylinder Head Gp
| 15***24 | Valve; (Exhaust) | 12 |
| 16***78 | Seal-Valve Stem; (Exhaust) | 24 |
| 17***18 | Cylinder Head Group | 1 |
263-5055 Cylinder Head Gp
| 15***24 | Valve; (Exhaust) | 12 |
| 16***78 | Seal-Valve Stem; (Exhaust) | 24 |
| 18***01 | Rotocoil Assem. | 24 |
116-1085 Cylinder Head Gp
| 11***85 | Cylinder Head Group | 1 |
| 14***49 | Cylinder Head Group | 1 |
| 18***07 | Gasket As-Cylinder Head | 1 |
223-9250 Cylinder Head Gp
| 15***23 | Valve; (Inlet) | 12 |
| 15***24 | Valve; (Exhaust) | 12 |
| 16***78 | Seal-Valve Stem; (Exhaust) | 24 |
176-9918 Cylinder Head Gp
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
192-8982 Damper & Pulley Gp
| 16***25 | Damper Assem. | 1 |
| 17***92 | Adapter | 1 |
| 19***82 | Damper & Pulley Group | 1 |
193-2261 Damper & Pulley Gp
| 14***71 | Bolt; (5/8-18x9-In) | 6 |
| 16***26 | Damper Assem. | 1 |
| 19***61 | Damper & Pulley Group | 1 |
6i-3638 Drive Gp-Pump
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 3 |
| 13***07 | Adapter Group-Pump Drive; -Remote | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
116-1083 Fastener Gp-Cylinder Head
| 11***83 | Fastener Group-Cylinder Head; (Cylinder Head) | 1 |
| 12***84 | Bolt; (Hex Head) (M16x2x160mm) | 26 |
| 2S***58 | Washer-Hard; (17x29x3-mm Thk)(Engine Brake) | 26 |
4p-6846 Fastener Gp-Front Housing
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 4P***46 | Fastener Group-Front Housing; -Remote | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 2 |
108-9382 Fastener Gp-Front Housing
| 10***82 | Fastener Group-Front Housing | 1 |
| 14***68 | Stud-Taperlock | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 2 |
112-2644 Fastener Gp-Front Housing
| 11***44 | Fastener Group-Front Housing | 1 |
| 14***67 | Stud-Taperlock, Plug,Female | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 2 |
204-5024 Fastener Gp-Front Housing
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 2 |
| 20***48 | Stud-Taperlock | 2 |
| 20***24 | Fastener Group-Front Housing | 1 |
138-2539 Fastener Gp-Front Housing
| 13***39 | Fastener Group-Front Housing | 1 |
| 6V***49 | Nut-Hard; (M12 X 1.75) | 2 |
| 7D***49 | Washer (Flywheel Counter Balance Weight) | 2 |
176-7007 Fastener Gp-Oil Pan
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 24 |
| 17***07 | Fastener Group-Oil Pan | 1 |
| 24***14 | Sleeve As | 24 |
109-1657 Fastener Gp-Valve Mechanism
| 10***57 | Fastener Group-Valve Mechanism | 1 |
| 5J***94 | Screw,Cap,Socket He Manifold Mtg | 12 |
| 8L***13 | Strap-Cable(Tie 5.50" Long) | 6 |
102-3596 Flywheel Gp
| 10***96 | Flywheel Group | 1 |
| 16***24 | Flywheel As | 1 |
| 4N***14 | Gear; (113-Teeth)(Flywheel Starter) | 1 |
154-6189 Flywheel Gp
| 0S***76 | Bolt 5.08 cm(2 In.) Long | 12 |
| 13***76 | Flywheel As | 1 |
| 15***89 | Flywheel Group | 1 |
204-9316 Gear Gp-Camshaft
| 10***26 | Dowel | 1 |
| 20***16 | Gear Group-Camshaft | 1 |
| 9X***72 | Bolt-Locking; (3/8-16x0.875-In) | 16 |
117-2750 Gear Gp-Front
| 11***50 | Gear Group-Front | 1 |
| 13***83 | Shaft | 1 |
| 13***86 | Gear As; (Idler) (71 Teeth) | 1 |
208-9490 Gear Gp-Front
| 03***85 | Bolt-12 Point Hd-Engine Flywheel To | 6 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 10***68 | Bearing-Sleeve | 1 |
205-1230 Housing Gp-Flywheel
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
| 14***68 | Seal-Crankshaft; (Rear)(Flywheel Housing) | 1 |
117-2775 Housing Gp-Flywheel
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 11***75 | Housing Group-Flywheel | 1 |
| 14***73 | Housing-Flywheel, Threaded Tie-Rod, Threaded Tie-Rod; Replaces 421694a1 | 1 |
212-8137 Housing Gp-Front
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 11 |
133-7075 Housing Gp-Front
| 11***24 | Gear; (Pump Drive) (34 Teeth) | 1 |
| 13***75 | Housing Group-Front | 1 |
| 16***66 | Seal Group-Crankshaft; (Front) | 1 |
159-8621 Housing Gp-Front
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 11 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
192-1563 Idler Gp-Belt -Alternator, Refrigerant Compressor
| 14***11 | Pulley As-Idler | 1 |
| 14***01 | Cover-Dust; (Rear) | 1 |
| 15***98 | Spacer; (10.4x38.1x20-mm Thk) | 1 |
148-2063 Lifter Gp-Valve -Mechanism
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 2 |
| 12***93 | Dowel | 1 |
| 14***63 | Lifter Group-Valve; -Mechanism | 1 |
111-2088 Lifting Gp-Engine
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 10***85 | Eye-Lifting | 1 |
| 11***88 | Lifting Group-Engine; (Rear) | 1 |
112-2418 Lifting Gp-Engine
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 10***86 | Eye-Lifting | 1 |
| 11***18 | Lifting Group-Engine | 1 |
117-2748 Lifting Gp-Engine
| 11***05 | Plate; (Lifting Eye) | 2 |
| 11***48 | Lifting Group-Engine | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 6 |
148-7482 Mechanism Gp-Fuel Pump & Valve
| 14***82 | Mechanism Group-Fuel Pump & Valve | 1 |
| 19***98 | Rocker Arm Group | 3 |
| 6I***58 | Bridge-Valve | 12 |
190-0009 Mechanism Gp-Fuel Pump & Valve
| 19***09 | Mechanism Group-Fuel Pump & Valve | 1 |
| 32***36 | Rocker Arm Group; -Non-Brake | 3 |
| 6I***58 | Bridge-Valve | 12 |
252-5557 Mounting Gp-Belt Tensioner
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
197-7433 Mounting Gp-Belt Tensioner
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
243-3014 Mounting Gp-Belt Tensioner
| 15***00 | Bolt; (M10x1.5x54.25-mm) | 1 |
| 16***58 | Cover; (Dust) | 1 |
| 17***98 | Pulley As-Idler; (8-Groove) | 2 |
197-7432 Mounting Gp-Belt Tensioner
| 14***01 | Cover-Dust; (Rear) | 1 |
| 15***00 | Bolt; (M10x1.5x54.25-mm) | 2 |
| 16***58 | Cover; (Dust) | 1 |
138-2550 Mounting Gp-Fan Drive
| 12***64 | Stud; (M12x1.75x86.3-mm Oal) | 2 |
| 13***50 | Mounting Group-Fan Drive; (Short) | 1 |
| 5R***37 | Washer; (Seal) (1.27mm Thk) | 2 |
116-5408 Mounting Gp-Valve Mechanism
| 11***83 | Fastener Group-Cylinder Head; (Cylinder Head) | 1 |
| 11***08 | Mounting Group-Valve Mechanism | 1 |
| 17***68 | Bridge As-Valve; (Intake) | 12 |
250-1884 Pan Gp-Oil
| 06***58 | Seal-O-Ring; (Oil Pan Drain Plug) | 2 |
| 10***08 | Gasket; (Oil Pan) | 1 |
| 12***57 | Bell As; (Suction) | 1 |
196-2111 Pan Gp-Oil
| 06***58 | Seal-O-Ring; (Oil Pan Drain Plug) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
126-0144 Pan Gp-Oil -Engine
| 06***58 | Seal-O-Ring; (Oil Pan Drain Plug) | 2 |
| 10***08 | Gasket; (Oil Pan) | 1 |
| 12***57 | Bell As; (Suction) | 1 |
134-3071 Piston & Rod Gp
| 13***71 | Piston & Rod Group | 1 |
| 13***05 | Ring-Piston; (Oil Control) | 1 |
| 14***30 | Ring-Piston; (Intermediate) | 1 |
176-5745 Piston & Rod Gp
| 13***63 | Skirt-Piston | 1 |
| 13***61 | Ring-Piston; (Top)(Top) | 1 |
| 15***25 | Bolt; (7/16-14-2a-Thd) | 1 |
130-0863 Piston & Rod Gp
| 11***99 | Plug-Pin | 2 |
| 11***16 | Rod Assem. | 1 |
| 11***72 | Bearing-Connecting Rod | 1 |
234-9706 Plug Gp-Cylinder Block
| 23***06 | Plug Group-Cylinder Block; -Remote | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
| 6V***09 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
191-6520 Plug Gp-Cylinder Block
| 19***20 | Plug Group-Cylinder Block | 1 |
| 21***66 | Seal-O-Ring; (Engine Oil) | 1 |
| 30***30 | Accessory Drive Pulley, Plug As | 1 |
247-8211 Plug Gp-Cylinder Block
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 13***27 | Seal-O-Ring; (19.18mm Id Base Side) | 1 |
| 18***09 | Plug As; (High Temperature) | 1 |
235-1591 Plug Gp-Cylinder Block
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 13***27 | Seal-O-Ring; (19.18mm Id Base Side) | 1 |
| 18***09 | Plug As; (High Temperature) | 1 |
138-2028 Plug Gp-Cylinder Block
| 13***28 | Plug Group-Cylinder Block | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
305-9196 Plug Gp-Cylinder Block
| 30***96 | Plug Group-Cylinder Block | 1 |
| 6V***65 | O-Ring - For Oil Fill Plug | 1 |
| 9S***10 | Plug; (Straight Thread O-Ring)(Cylinder Head) | 1 |
117-0165 Plug Gp-Cylinder Block
| 11***65 | Plug Group-Cylinder Block; -Oil Gallery, End | 1 |
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 1 |
117-0185 Plug Gp-Cylinder Block
| 11***85 | Plug Group-Cylinder Block; (Cylinder Block) | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 1 |
| 9S***06 | Plug (Front 5 Stem Main Control Valve) | 1 |
110-1116 Plug Gp-Cylinder Head
| 11***16 | Plug Group-Cylinder Head | 1 |
| 7W***92 | Plug-Pipe; (1/2-14 Nptf Thd)(Use Without Air Compressor) | 1 |
234-9184 Plug Gp-Cylinder Head
| 18***08 | Plug As; (High Temperature) | 4 |
| 23***84 | Plug Group-Cylinder Head; -Remote | 1 |
| 6V***51 | Seal-O-Ring (Id=19.18mm) | 1 |
234-9775 Plug Gp-Engine
| 23***75 | Plug Group-Engine; -Remote | 1 |
| 6V***09 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
| 8L***86 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
234-9776 Plug Gp-Engine
| 23***76 | Plug Group-Engine; -Remote | 1 |
| 6V***09 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
| 9S***05 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
328-4238 Rocker Arm Gp
| 06***39 | Seal-O-Ring | 1 |
| 19***51 | Button; (24-mm Od) | 1 |
| 19***69 | Screw-Arm Adjustment; (9/16-18x2-In) | 1 |
115-9397 Rocker Arm Gp
| 09***14 | Pin; (Spring) | 1 |
| 11***97 | Rocker Arm Group | 1 |
| 11***98 | Arm; (Valve Rocker) (Exhaust) | 2 |
328-4236 Rocker Arm Gp
| 30***22 | Shaft As-Rocker Arm, Exhaust Manifold | 1 |
| 32***96 | Rocker Arm Group; -Intake | 4 |
| 32***36 | Rocker Arm Group; -Non-Brake | 1 |
278-1931 Rocker Arm Gp
| 06***39 | Seal-O-Ring | 2 |
| 19***51 | Button; (24-mm Od) | 2 |
| 19***69 | Screw-Arm Adjustment; (9/16-18x2-In) | 2 |
198-9898 Rocker Arm Gp
| 03***13 | Seal-O-Ring | 2 |
| 06***39 | Seal-O-Ring | 2 |
| 19***51 | Button; (24-mm Od) | 2 |
278-1929 Rocker Arm Gp
| 06***39 | Seal-O-Ring | 2 |
| 19***51 | Button; (24-mm Od) | 2 |
| 19***69 | Screw-Arm Adjustment; (9/16-18x2-In) | 2 |
320-2796 Rocker Arm Gp -Intake
| 25***21 | Button | 1 |
| 27***91 | Screw-Arm Adjustment; (3/8-24x1.20-In) | 1 |
| 27***17 | Nut; (3/8-24-Thd) | 1 |
116-1091 Seal Gp-Crankshaft
| 10***80 | Seal-O-Ring (Id=177.17mm) | 1 |
| 11***91 | Seal Group-Crankshaft; -Single Lip | 1 |
| 16***23 | Cover | 1 |
319-7401 Seal Gp-Crankshaft -Front
| 14***67 | Seal Group-Crankshaft; (Front) | 1 |
| 31***01 | Seal Group-Crankshaft; -Front | 1 |
193-7413 Support Gp-Engine
| 19***65 | Support As | 1 |
| 19***13 | Support Group-Engine | 1 |
| 2H***88 | Bolt- 12 cm(4.75 In.) Long-Location "F" | 8 |
193-7412 Support Gp-Engine
| 19***61 | Support As | 1 |
| 19***12 | Support Group-Engine | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 8 |
117-2749 Valve Mechanism Gp -Engine
| 10***42 | Base-Valve Mechanism Cover | 1 |
| 10***67 | Pushrod; (Valve) | 12 |
| 10***68 | Pushrod-Injector | 6 |
Cooling System
115-2990 Cooler Gp-Engine Oil
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 10***25 | Gasket | 1 |
| 11***90 | Cooler Group-Engine Oil; (Engine Oil) | 1 |
163-1628 Fastener Gp-Oil Cooler -Engine
| 16***28 | Fastener Group-Oil Cooler; -Engine | 1 |
| 17***99 | Stud; (3/8-16-Thd) | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 1 |
117-2792 Fastener Gp-Oil Cooler -Engine
| 11***92 | Fastener Group-Oil Cooler; -Engine | 1 |
| 6V***17 | Bolt; (M8x1.25x30-mm)(Location Z) | 1 |
| 9M***74 | Washer-Hard; (8.8x16x2-mm Thk)(Hard) | 1 |
109-2373 Fastener Gp-Water Pump
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***73 | Fastener Group-Water Pump; (Water Pump Cover) | 1 |
116-5456 Housing & Regulator Gp -Engine Coolant Temperature
| 11***56 | Housing & Regulator Group; -Engine Coolant Temperature | 1 |
| 11***00 | Housing As-Regulator | 1 |
| 12***11 | Stud; (M8x1.25-Thd)(M8x1.25 Thd Both Ends) | 4 |
116-5460 Lines Gp-Water -Bypass
| 10***08 | Flange | 1 |
| 10***95 | Tube | 1 |
| 11***60 | Lines Group-Water; -Bypass | 1 |
117-2783 Lines Gp-Water -Single Thermostat
| 11***56 | Housing & Regulator Group; -Engine Coolant Temperature | 1 |
| 11***83 | Lines Group-Water; -Single Thermostat | 1 |
| 11***97 | Gasket | 4 |
195-7999 Lines Gp-Water
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 5 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
116-5446 Lines Gp-Water -Water Pump Inlet Elbow
| 10***35 | Gasket | 1 |
| 11***46 | Lines Group-Water; -Water Pump Inlet Elbow | 1 |
| 11***57 | Elbow-Water Pump | 1 |
117-2789 Plug Gp-Water Lines
| 11***89 | Plug Group-Water Lines; -Engine Oil Cooler | 1 |
| 6V***27 | Seal-O-Ring (Id=8.92mm) | 1 |
| 8T***67 | Plug-Pipe; (Oil Cooler Bonnet Drain) | 1 |
174-5986 Pump Gp-Water
| 10***77 | Seal-O-Ring; (100.97mm Id) | 1 |
| 12***72 | Seal-O-Ring (215.49mm Id) | 1 |
| 16***19 | Pump Group-Water | 1 |
161-5719 Pump Gp-Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***30 | Bearing As-Roller | 1 |
| 12***17 | Seal Group; (Water Pump) | 1 |
117-2674 Pump Gp-Water
| 11***74 | Pump Group-Water | 1 |
| 17***00 | Pump Group-Water | 1 |
| 6V***21 | Bolt; (M8x1.25x80-mm) | 2 |
176-7000 Pump Gp-Water
| 10***10 | Gasket | 1 |
| 14***88 | Seal As; (Water Pump) | 1 |
| 17***95 | Cover-Pump | 1 |
Electrical And Starting System
124-2674 Connection Gp-Electrical
| 12***74 | Connection Group-Electrical; -Ground | 1 |
| 5C***61 | Nut (M8x1.25 Thd); (M8x1.25 Thd) | 1 |
| 6V***64 | Washer-Hard; (8.8x25.5x5-mm Thk) | 1 |
126-7631 Connection Gp-Electrical
| 12***31 | Connection Group-Electrical; (Cylinder Block Ground) | 1 |
| 12***49 | Stud; (3/8-16, 5/8-18x3.1-In) | 1 |
| 5P***47 | Washer (Bracket To Valve Support) | 1 |
159-9107 Connection Gp-Electrical -Cylinder Head Ground
| 15***07 | Connection Group-Electrical; -Cylinder Head Ground | 1 |
| 17***99 | Stud; (3/8-16-Thd) | 1 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 1 |
168-4490 Control & Mtg Gp-Engine Elek
| 16***90 | Control & Mtg Group-Engine Elek | 1 |
| 16***94 | Spacer; (8.5x12.7x54.1-mm) | 2 |
| 21***49 | Control Group-Engine Electronic | 1 |
191-5208 Control & Mtg Gp-Engine Elek
| 12***11 | Spacer; (3x15x17-mm Thk) | 1 |
| 15***96 | Support As | 1 |
| 15***98 | Support As | 1 |
210-0849 Control Gp-Engine Electronic
| 21***49 | Control Group-Engine Electronic | 1 |
| 32***03 | Control Group-Engine Electronic | 1 |
210-0848 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 21***48 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
322-3603 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 32***03 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
240-5304 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 24***04 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
178-3091 Control Gp-Engine Electronic
| 17***91 | Control Group-Engine Electronic | 1 |
| 21***48 | Control Group-Engine Electronic | 1 |
192-1623 Mounting Gp-Sensor
| 16***93 | Adapter | 1 |
| 19***23 | Mounting Group-Sensor | 1 |
| 1T***20 | Bolt-12 Point Head; (3/8-16x1.25-In) | 1 |
235-4557 Sensor Gp-Engine
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 11***82 | Seal-O-Ring; (16.36mm Id) | 1 |
| 13***11 | Sensor Group-Temperature; (Transmission Lubrication Oil) | 3 |
192-0883 Sensor Gp-Engine
| 00***17 | Elbow | 1 |
| 03***78 | Connector-Filtered Fuel To Adapter | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
197-8395 Sensor Gp-Pressure
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
| 19***95 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
194-6724 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 3 |
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
194-6722 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 19***22 | Sensor Group-Pressure; -Atmospheric Air | 1 |
197-8394 Sensor Gp-Pressure
| 16***05 | Sensor As-Pressure; (Unfiltered Engine Oil) | 1 |
| 19***94 | Sensor Group-Pressure; -Engine Oil | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
194-6725 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 19***25 | Sensor Group-Pressure; -Engine Oil | 1 |
197-8393 Sensor Gp-Pressure
| 16***03 | Sensor Group-Pressure; (Turbocharger Inlet, Rh) | 1 |
| 19***93 | Sensor Group-Pressure; -Atmospheric | 1 |
| 21***68 | Seal-O-Ring; (11.89-mm Id) | 1 |
197-8396 Sensor Gp-Speed
| 18***11 | Sensor Group-Speed; (Crankshaft Timing) | 1 |
| 19***96 | Sensor Group-Speed; -Timing, Crankshaft | 1 |
| 20***40 | Seal-O-Ring; (13.94mm Id) | 1 |
197-8397 Sensor Gp-Speed
| 18***01 | Sensor Group-Speed; (Camshaft Timing) | 1 |
| 19***97 | Sensor Group-Speed; -Timing, Camshaft | 1 |
| 20***40 | Seal-O-Ring; (13.94mm Id) | 1 |
197-8391 Sensor Gp-Temperature
| 13***11 | Sensor Group-Temperature; (Transmission Lubrication Oil) | 1 |
| 13***45 | Pad; (Connector) | 1 |
| 19***91 | Sensor Group-Temperature; -Air Inlet Manifold | 1 |
197-8392 Sensor Gp-Temperature
| 13***45 | Pad; (Connector) | 1 |
| 19***92 | Sensor Group-Temperature; -Coolant, Water | 1 |
| 26***97 | Sensor Group-Temperature; (Air Inlet Manifold) | 1 |
191-6130 Wiring Gp-Electronic Control
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***76 | Bolt 5.08 cm(2 In.) Long | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
226-2312 Wiring Gp-Engine
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***76 | Bolt 5.08 cm(2 In.) Long | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
171-1103 Wiring Gp-Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***89 | Clip; (Ladder) | 1 |
117-2760 Wiring Gp-Unit Injector
| 11***60 | Wiring Group-Unit Injector | 1 |
| 2V***16 | Clip; (9.52mm Id) | 4 |
| 4P***37 | Harness Assembly-Wiring; (Unit Injector) | 1 |
Engine Arrangement
235-4673 Engine Ar-Complete
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***37 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***12 | Fitting Group-Quick Disconnect; -Fuel | 1 |
235-4672 Engine Ar-Complete
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***37 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***12 | Fitting Group-Quick Disconnect; -Fuel | 1 |
172-6955 Engine Ar-Complete
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***37 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***12 | Fitting Group-Quick Disconnect; -Fuel | 1 |
172-6946 Engine Ar-Complete
| 10***96 | Flywheel Group | 1 |
| 11***85 | Cover Group-Cylinder Block | 1 |
| 11***90 | Cooler Group-Engine Oil; (Engine Oil) | 1 |
172-6957 Engine Ar-Complete
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***37 | Cover Group-Cylinder Block; -Remote | 1 |
| 10***12 | Fitting Group-Quick Disconnect; -Fuel | 1 |
172-6945 Engine Ar-Complete
| 10***96 | Flywheel Group | 1 |
| 11***85 | Cover Group-Cylinder Block | 1 |
| 11***90 | Cooler Group-Engine Oil; (Engine Oil) | 1 |
185-6147 Engine Ar-Core
| 11***83 | Cylinder Block Group | 1 |
| 11***85 | Cylinder Head Group | 1 |
| 11***05 | Manifold Group-Inlet | 1 |
185-6150 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 13***71 | Piston & Rod Group | 6 |
235-3450 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 14***82 | Mechanism Group-Fuel Pump & Valve | 1 |
235-3451 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 13***71 | Piston & Rod Group | 6 |
185-6149 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 14***82 | Mechanism Group-Fuel Pump & Valve | 1 |
185-6148 Engine Ar-Core
| 11***83 | Cylinder Block Group | 1 |
| 11***85 | Cylinder Head Group | 1 |
| 11***05 | Manifold Group-Inlet | 1 |
Fuel System
116-5436 Filter Gp-Fuel
| 11***36 | Filter Group-Fuel; -Secondary | 1 |
| 1R***62 | Filter As-Fuel; (Advanced Efficiency)(Secondary) | 1 |
213-5207 Fitting Gp-Fuel Lines
| 21***07 | Fitting Group-Fuel Lines | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 6V***98 | Seal-O-Ring -Line From Gear Pump Output | 1 |
116-5434 Fitting Gp-Fuel Lines
| 11***34 | Fitting Group-Fuel Lines | 1 |
| 11***35 | Connector | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
213-5208 Fitting Gp-Fuel Lines
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 21***08 | Fitting Group-Fuel Lines | 1 |
| 2R***06 | Connector Valve Assembly To; Connector- Tube Assembly To Logic Valve | 1 |
108-2312 Fitting Gp-Quick Disconnect
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 10***12 | Fitting Group-Quick Disconnect; -Fuel | 1 |
| 6V***52 | Cap-Dust; (Fuel Supply Tee Connection) | 1 |
203-7685 Injector Gp-Fuel
| 11***84 | Seal-O-Ring; (32.99mm Id) | 1 |
| 20***85 | Injector Group-Fuel | 1 |
| 21***98 | Seal-O-Ring; (34.56mm Id) | 1 |
170-5252 Injector Gp-Fuel
| 11***84 | Seal-O-Ring; (32.99mm Id) | 1 |
| 17***52 | Injector Group-Fuel | 1 |
| 9X***17 | Seal-O-Ring; (9.6mm Id) | 1 |
128-8510 Injector Gp-Fuel
| 10***72 | Spacer; (9.8x15.85x37.6-mm Thk) | 1 |
| 12***10 | Injector Group-Fuel | 1 |
| 21***25 | Injector Group-Fuel | 1 |
216-7887 Lines Gp-Fuel
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 2 |
| 11***02 | Hose As | 1 |
| 11***16 | Hose Assem. | 1 |
193-1561 Lines Gp-Fuel
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 2 |
| 03***28 | Seal-O-Ring | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 12 |
189-0351 Pump Gp-Fuel Injection
| 15***01 | Bolt; (8x1.25x7-mm)(M8x1.25x70mm) | 1 |
| 18***51 | Pump Group-Fuel Injection | 1 |
| 20***85 | Injector Group-Fuel | 1 |
116-5411 Pump Gp-Fuel Priming -Hand
| 11***11 | Pump Group-Fuel Priming; -Hand | 1 |
| 13***41 | Pump Group-Fuel Priming; (Hand) | 1 |
| 1P***36 | Gasket; (Fuel Priming Pump)(Fuel Priming Pump) | 1 |
145-1695 Pump Gp-Fuel Transfer
| 09***70 | Washer-Sealing | 2 |
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 1 |
| 14***95 | Pump Group-Fuel Transfer | 1 |
139-9094 Pump Gp-Fuel Transfer
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 2 |
| 13***03 | Cover-Pump | 1 |
| 13***94 | Pump Group-Fuel Transfer; -Remote | 1 |
139-9095 Pump Gp-Fuel Transfer
| 0S***73 | Stud | 2 |
| 10***72 | Cover; (Hydraulic Pump Drive) | 1 |
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 2 |
156-5783 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 15***83 | Valve Group-Check; -Fuel | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
238-0296 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 23***96 | Valve Group-Check; -Fuel Filter | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
233-6742 Valve Gp-Check -Fuel
| 23***42 | Valve Group-Check; -Fuel Filter | 1 |
| 28***25 | Valve Group-Check; -Fuel | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 1 |
281-2725 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 28***25 | Valve Group-Check; -Fuel | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
Lubrication System
176-1363 Base Gp-Oil Filter -Engine
| 17***63 | Base Group-Oil Filter; -Engine | 1 |
| 2P***04 | Stud-Hollow; (1.5-16x1.339-In) | 1 |
| 9L***57 | Plug-Cup | 2 |
154-4327 Base Gp-Oil Filter -Engine
| 15***27 | Base Group-Oil Filter; -Engine | 1 |
| 17***63 | Base Group-Oil Filter; -Engine | 1 |
| 1P***67 | Plunger; (Engine Oil Cooler Relief Valve) | 2 |
166-1329 Base Gp-Oil Filter -Engine
| 11***45 | Valve-Pump Bypass; (Engine Oil Filter) | 1 |
| 16***28 | Base Assem. | 1 |
| 16***29 | Base Group-Oil Filter; -Engine | 1 |
155-5005 Base Gp-Oil Filter
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***80 | Elbow | 1 |
209-6302 Base Gp-Oil Filter -Engine
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***27 | Base Group-Oil Filter; -Engine | 1 |
117-2786 Cover Gp-Oil Filter Base -Engine
| 11***86 | Cover Group-Oil Filter Base; -Engine | 1 |
| 5S***34 | Seal-O-Ring; (97.79mm Id) | 1 |
| 7C***42 | Cover; (Filter Base) | 1 |
4n-2481 Fastener Gp-Oil Pump Mounting -Engine
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 4N***81 | Fastener Group-Oil Pump Mounting; Oil Pump Mounting Fastener Group | 1 |
192-8992 Filler Gp-Engine Oil
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 1 |
| 19***92 | Filler Group-Engine Oil | 1 |
| 19***53 | Bracket | 1 |
192-8993 Filler Gp-Engine Oil
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 19***93 | Filler Group-Engine Oil | 1 |
| 19***32 | Cap As; (Engine Oil Filler) | 1 |
110-8876 Filler Gp-Engine Oil
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 10***99 | Tube As-Oil Filler; (Engine) | 1 |
| 11***76 | Filler Group-Engine Oil | 1 |
226-2313 Filler Gp-Engine Oil -Left Front
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 19***32 | Cap As; (Engine Oil Filler) | 1 |
| 22***58 | Tube-Oil Filler | 1 |
154-4325 Filter Gp-Engine Oil
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 12***72 | Stud-Mounting; (3/8-16x1.564-In)(3/8-16 Thd) | 2 |
209-5777 Filter Gp-Engine Oil
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
117-2751 Filter Gp-Engine Oil
| 11***51 | Filter Group-Engine Oil | 1 |
| 13***45 | Bolt-Hex Head; (M10x1.50x30) | 6 |
| 16***29 | Base Group-Oil Filter; -Engine | 1 |
123-0783 Valve Gp-Fluid Sampling
| 12***83 | Fitting Group-Fuel Lines; -Fuel | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6V***52 | Cap-Dust; (Fuel Supply Tee Connection) | 1 |
212-8218 Fumes Disposal Gp
| 19***32 | Hose As-Fumes; (Disposal) | 1 |
| 19***49 | Bracket | 1 |
| 21***18 | Fumes Disposal Group | 1 |
143-2656 Gauge Gp-Oil Level (Dipstick)
| 12***19 | Gauge As-Oil Level (Dipstick) | 1 |
| 14***54 | Tube As-Gauge Guide | 1 |
| 14***56 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
217-4518 Guide Gp-Oil Level Gauge
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 11***68 | Seal-O-Ring; (15.54mm Id) | 1 |
| 16***70 | Plug | 3 |
138-4773 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 10***44 | Elbow | 1 |
209-7314 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 10***44 | Elbow | 1 |
| 11***87 | Seal-O-Ring (23.16 mm Id) | 1 |
211-2820 Lines Gp-Turbocharger Oil
| 10***69 | Tube As; (Oil) | 1 |
| 11***87 | Seal-O-Ring (23.16 mm Id) | 1 |
| 11***42 | Adapter | 1 |
235-2421 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 10***44 | Elbow | 1 |
| 11***87 | Seal-O-Ring (23.16 mm Id) | 1 |
165-0592 Lines Gp-Turbocharger Oil
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 11***87 | Seal-O-Ring (23.16 mm Id) | 1 |
| 11***42 | Adapter | 1 |
161-4113 Pump Gp-Engine Oil
| 12***56 | Cover As-Pump | 1 |
| 16***13 | Pump Group-Engine Oil | 1 |
| 1M***44 | Bolt; (3/8-16x2-1/4 In) | 2 |
233-5220 Pump Gp-Engine Oil
| 23***20 | Pump Group-Engine Oil | 1 |
| 6D***46 | Seal-O-Ring (Id=101.27mm) | 1 |
| 6V***17 | Bolt; (M8x1.25x30-mm)(Location Z) | 4 |
117-2746 Pump Gp-Engine Oil
| 06***61 | Seal-O-Ring (Id=40.87mm) | 1 |
| 11***03 | Tube Assem. | 1 |
| 11***46 | Pump Group-Engine Oil | 1 |
138-2535 Valve Gp-Fluid Sampling -Engine Oil
| 13***35 | Valve Group-Fluid Sampling; -Engine Oil | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 5P***17 | Adapter- To Logic Valve 1u***59 | 1 |
MT835 serial number reference
The PIN/serial plate is mounted on the left side of the tractor's main frame. The plate shows the full Product Identification Number; the first three letters are the serial-number prefix that ties the unit to its model family (BAM for MT835), and the digits that follow are the sequential build number, which also tracks roughly with the production year.
| Prefix | Identifies | Notes |
|---|---|---|
| BAM | MT835 track tractor (base model, Caterpillar/Challenger-badged; not the later B or C generation) | Sole serial prefix tied to the plain MT835 track tractor, built 2002-2004. Sequence numbers climbed with model year: BAM20000-range for 2002-built units, BAM30000-range for 2003, BAM40000-range for 2004 production, with a parts manual scoping the tail of that run to BAM40001-59999. Fitted with a turbocharged Caterpillar C-12 diesel, 11.9 L (729 cu in), 6-cylinder, rated near 340 hp (253 kW) gross. Early 2002 and early-2003 units were assembled at the former Caterpillar track-tractor plant in DeKalb, Illinois during the Caterpillar-to-AGCO ownership changeover; that plant stopped track-tractor production by mid-2003 and the line shifted to AGCO's Jackson, Minnesota plant, which built the balance of 2003 output and all 2004 output. Later MT835B (2005-2008, Caterpillar 15.2L/C15 engine) and MT835C (2009-2013) generations use their own serial designations and are not covered by this prefix - confirm with your dealer if working from a B- or C-suffix machine. |
Frequently asked questions
What engine does the Caterpillar Challenger MT835 use?
The original 2002-2004 MT835 runs a Caterpillar C12 11.9L inline-six turbo-diesel rated at a gross 340 hp (253 kW), a mechanical, non-ACERT engine with no exhaust aftertreatment. Later tractors badged MT835B (2005-2008) and MT835C (2009-2013) reuse the same model number but carry a larger Caterpillar C15 ACERT engine instead, so always confirm the serial prefix before assuming which engine a given machine has.
What is the operating weight of the MT835?
Base operating weight is approximately 18,140 kg (40,000 lb), though the figure varies by belt width, ballast, and optional equipment fitted. Fuel tank size (1154.4 L/305 US gal standard, 1249.0 L/330 US gal optional) and any added counterweights shift the number further, so treat 40,000 lb as a nominal reference rather than an exact figure for any one unit.
What replaced the Caterpillar Challenger MT835?
AGCO replaced the original C12-powered MT835 with the MT835B starting in 2005, which carries a larger Caterpillar C15 ACERT engine rated near 350 hp. A further MT835C generation followed from 2009 to 2013 with a 410 hp C15 ACERT engine. Both later tractors share the MT835 model number but not the engine or electronics of the 2002-2004 original.
What MT835 owners discuss
What do owners and techs say about the Cat C12 engine in the original MT835?
The 11.9L C12 turbo-diesel in this generation (2002-2004, BAM-prefix serials) uses mechanically actuated, electronically controlled unit injection with air-to-air aftercooling, rated 340 hp (254 kW) gross - it predates the ACERT emissions-era engines and carries no EGR or DPF. Consensus among diesel techs is that it's a strong, torquey block that's straightforward to work on and holds up well when serviced on schedule. The main wear item to watch is injector balance: as the high-pressure oil pump and unit injectors age, cylinder balance can drift, and that's the first thing to check on a rough-running or low-power complaint before chasing fuel filters. With no glow-plug-free cold-start aid on this engine, cold weather starts lean on glow plugs plus ether; a stubborn cold no-start is more often a weak battery or failing glow-plug relay than a fuel problem.
How does the 16-speed powershift transmission and hydraulic reverser hold up?
This generation runs a 16-forward/4-reverse electronically controlled powershift, not the CVT used on the wheeled Challenger line - don't compare wear patterns across the two. If the transmission throws a fault during clutch-fill calibration, techs point to two causes: a worn clutch pack or a leaking modulating valve/seal at that gear's apply piston, since a worn pack lets the piston travel further before it seats, showing up as a long fill time. The hydraulic reverser sees hard use in loader-style front work, and running it in high range wears its clutch pack faster than normal shuttle-range use - a commonly cited cause of premature reverser wear. Otherwise the powershift and final drives are described as durable for this class of machine when fluid and filter service isn't skipped.
What undercarriage wear points come up most for the rubber Mobil-Trac belt system?
Belt tension is held by a nitrogen-charged accumulator and hydraulic cylinder rather than a mechanical adjuster, with tension pressure viewable from the cab monitor - it should be checked routinely rather than trusted to the warning light alone. Mid-roller and front-idler rubber wears with soil type and abrasiveness; once that rubber layer thins to only a few millimeters, the rollers and idlers need re-rubbering or replacing. Belt life itself is heavily duty-cycle dependent (row-crop vs. tillage work), and the two things that end a belt's service life are outer cleat wear and stone damage cutting through to the inner carcass canvas. A track that feels soft or slow to firm back up usually points to a weeping accumulator seal rather than a bad cylinder. Nitrogen accumulators are pressurized and must only be charged with dry nitrogen, never oxygen or shop air - have your dealer verify accumulator condition and charge pressure before servicing.
What hydraulic quirks show up on these Challenger track tractors?
Remote/implement circuits use quick couplers at the valve stack, and owners report coupler tips can work loose or pop out under pressure if not fully seated - if a remote loses pressure intermittently, reseat the coupler and check its retaining collar before suspecting the valve. On the loader/tilt circuit, driving an attachment into the ground while the tractor is still moving is the classic way to blow the OEM O-rings on the tilt side of the control valve; it's a simple reseal, but easy to avoid by lifting the implement before repositioning. When running implements with their own case-drain return (some grain-cart meter drives), match the implement's case-drain flow to what the tractor's factory case-drain circuit is rated for - exceeding it backs up return oil and causes seal problems.
What sensor and electrical fault issues come up most on this generation?
Diagnostic references for this tractor commonly list oil-pressure sensor circuit faults (open or short), clutch-point pressure sensor faults on the high/low clutch circuits, and 5V-supply or main-relay faults in the ECU wiring - most of these trace back to a connector or harness fault rather than a bad sensor itself. On the transmission side, a clogged transmission-filter sensor code or a parking-brake sensor fault is usually exactly what it reports: change the filter or check brake switch adjustment before chasing wiring. As with any tractor of this age, chafed harness sections at grommets and pinch points are a common root cause behind intermittent or hard-to-reproduce fault codes.
What's the overall reliability consensus for this generation of MT835?
General consensus among owners and techs is that the engine and drivetrain are strong and comparatively simple to work on next to newer ACERT-era equipment, and well-maintained units are reported still running their original engine and transmission well into their service life. The recurring complaint isn't the machine itself but dealer support: Caterpillar exited the agricultural tractor business in the mid-2000s and the Challenger brand moved to AGCO, so parts and service for this generation route through AGCO/Challenger dealers rather than Cat dealers, and owners in some regions report having to travel farther for authorized service than they did when the machine was new.
What should I check before buying a used MT835?
First confirm you're actually looking at the original MT835 (2002-2004, C12 engine, BAM-prefix serial) and not a later MT835B or MT835C - those are different platforms with a different engine and rating despite sharing the model name, and pricing/parts don't cross over. Then check hours against maintenance records rather than relying on hours alone. Inspect the belts for outer cleat wear and any stone damage that exposes the inner carcass canvas - as a rule of thumb, half-worn tracks should be reflected in roughly half the value of new belts in the asking price. Check mid-roller and front-idler rubber thickness, and confirm track tension pressure holds rather than bleeding down overnight (a sign of a weeping accumulator). Run the transmission through every range and watch for a clutch-fill calibration fault, and specifically test the hydraulic reverser in high range since that's the fastest-wearing use case. On the engine, check the breather for excess smoke or blow-by and inspect intake hoses for cracks. Cycle the hydraulic remotes and couplers under load, and check the drawbar and frame for cracks or repair welds. Have your dealer verify any track tension, hydraulic, or transmission calibration reading that looks borderline before you commit to a price.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific MT835 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.