Caterpillarengine - generator setgenerator set
Caterpillar G3516
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar G3516 is a stationary, spark-ignited natural gas engine-generator set built around Cat's V-16, four-stroke 3500-series gas engine block, offered in lean-burn and turbocharged rich-burn configurations. It displaces roughly 67-69 liters from a 170 mm (6.7 in) bore and 190 mm (7.5 in) stroke, with a compression ratio that varies by configuration from about 8:1 on lean-burn ratings up to 11.5:1 on turbocharged standby ratings, and is offered naturally aspirated or turbocharged-aftercooled, running at 1200 rpm for 60 Hz output or 1500 rpm for 50 Hz output. Package output spans roughly 750 ekW continuous up to 1500 ekW standby, plus a mechanical-drive rating near 1029 bkW, depending on configuration. Bare engine weight runs around 9,200 kg (20,400 lb), and a complete packaged genset - generator end, cooling, and control panel included - ranges from around 11,800 kg (26,000 lb) on a continuous-rated package up to about 18,300 kg (40,400 lb) on a standby-rated package. The 3500-series block the G3516 is built on dates to the mid-1980s; the gas-fueled G3516 followed as part of Cat's lean-burn and rich-burn gas generator lineup and was offered with radiator, remote-radiator, or heat-exchanger cooling, set up for pipeline natural gas, landfill gas, or digester gas fuel.
Across the G3516 family, the biggest changes are in engine management and output rather than the base architecture. The original G3516 used earlier electronic governing and ignition control; later G3516B, G3516C, and G3516E generations added Cat's ADEM digital engine management, tighter detonation control, and higher power ratings, while today's G3516H pushes further into the higher-output class. That long, incremental development is why the G3516 still turns up widely in oil and gas, landfill and digester gas, and industrial standby service, and why used units and running cores stay easy to find. Because the gas engine shares its long block, crankshaft, and much of its architecture with the diesel 3516, parts availability and rebuild expertise are broad, which keeps overhaul costs and downtime lower than for less common gas engine platforms.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar G3516 specifications
Engine
| Configuration | V-16, 4-stroke-cycle spark-ignited natural gas engine built on the G3500 platform. Offered in turbocharged-aftercooled rich-burn (TA) and lean-burn (LE) configurations depending on rating. |
| Cylinders | 16 (V-16) |
| Bore x Stroke | 170 mm x 190 mm (6.7 x 7.5 in) on 1200-1400 rpm continuous and mechanical-drive ratings. Catalog listings for 1800 rpm, 1061-1500 ekW standby ratings show 170 mm x 215 mm (6.7 x 8.5 in) - bore/stroke varies by rating package, confirm the exact rating code with a dealer. |
| Displacement | 67.4-69 L (4210-4211 cu in) on 1200-1400 rpm ratings. 78 L (4765 cu in) listed for 1800 rpm, 1061-1500 ekW standby ratings. |
| Compression ratio | 8:1, 9:1 or 11:1 depending on rating (lean-burn LE vs rich-burn TA). 11.5:1 listed for 1800 rpm standby ratings. |
| Aspiration | Turbocharged, aftercooled. Single-stage aftercooling on continuous LE/TA ratings; two-stage aftercooling on the high-output mechanical-drive rating. |
| Governing / control | Electronic governor (Woodward 2301A) on generator-set ratings. Digital engine management (ADEM A4) on the mechanical-drive rating. |
| Power range | 1380 bhp (1029 bkW) at 1400 rpm, mechanical-drive rating. 750-770 ekW (937-962 kVA) continuous at 1200 rpm, 60 Hz. Up to 1500 ekW standby (0.8 pf) at 1800 rpm, 60 Hz. Power varies widely by rating package - not a single fixed output. |
| Emissions | Rich-burn (TA) configuration meets NSPS / nonattainment-area limits only with a customer-supplied three-way catalyst; uncatalyzed NOx runs high (over 20 g/bhp-hr) on this config. Lean-burn (LE) configuration runs low NOx (about 2 g/bhp-hr) without a catalyst. Standby ratings carry U.S. EPA stationary non-emergency certification. |
Weights
| Bare engine weight (wet) | 9,232 kg (20,352 lb) - mechanical-drive TA rating |
| Generator set weight, continuous rating | approx. 11,793 kg (26,000 lb) - 1200 rpm, 750-770 ekW low-voltage package |
| Generator set weight, standby rating | approx. 18,315 kg (40,384 lb) - 1800 rpm, 1061-1500 ekW package |
| Ground pressure | not applicable - stationary generator set / engine, not a mobile undercarriage machine |
Dimensions
| Bare engine footprint | length 3,654 mm (143.8 in), width 1,973 mm (77.7 in), height 2,281 mm (89.8 in) |
| Package dimensions, continuous rating | length 4,902 mm (193 in), width 1,753 mm (69 in), height 1,905 mm (75 in) - 1200 rpm, 750-770 ekW package, approximate, not for installation design |
| Package dimensions, standby rating | length 7,000 mm (275.6 in), width 2,345 mm (92.3 in), height 3,265 mm (128.5 in) - 1800 rpm, 1061-1500 ekW package |
| Note | Package dimensions vary with radiator or remote cooling, enclosure, and control-panel options - treat figures above as approximate for a base configuration. |
Performance
| Continuous rating (60 Hz, 1200 rpm) | 750-770 ekW / 937-962 kVA at 0.8-1.0 pf |
| Mechanical-drive rating (1400 rpm) | 1,380 bhp (1029 bkW) |
| Standby rating (60 Hz, 1800 rpm) | up to 1500 ekW at 0.8 pf |
| Electrical efficiency | about 32.5-35.1% at 1.0 pf, continuous rating |
| Thermal efficiency (heat recovery) | about 50-55%, depending on configuration |
| Generator voltage range | 480 V up to 4,160 V typical |
| Altitude capability | up to 1,524 m (5,000 ft) at rated torque/output and 25-38 degC ambient on most ratings; about 1,065 m (3,494 ft) on the higher-compression-ratio lean-burn setup. Output derates beyond the listed altitude. |
| Fuel consumption at 100% load | about 224-232 Nm3/hr (8,344-8,651 scf/hr) on continuous 1200 rpm ratings; 10.32 MJ/bkW-hr (7,300 Btu/bhp-hr) on the mechanical-drive rating |
| Motor-starting capability | about 1,950 skVA typical, at 30% voltage dip, synchronous driver assumed |
Service capacities (summary)
| Fuel | pipeline-quality natural gas, 800 to 1,200 Btu/cu ft (31.5-47.2 MJ/Nm3). Gas supply pressure 221-241 kPa (32-35 psig) to the engine fuel control valve. Hydrogen-blend fuel accepted up to 5% on some standby ratings. |
| Engine oil system (refill) | 401 L (106 gal) on continuous generator-set ratings; 423 L (112 gal) on the mechanical-drive TA rating. Oil change interval about 1,500 hours. |
| Cooling system, total capacity | about 218-225 L (57.5-59.2 gal), split roughly 200-205 L (53-54 gal) jacket water and 17-20 L (4.5-5.2 gal) aftercooler circuit - varies by rating/configuration |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
G3516 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with oil filter) | 424 L (112 US gal) refill capacity. Figure recurs consistently across TA (turbocharged-aftercooled) and LE (low-emission) rated G3516 builds. Standard oil change interval is 1000 hours, extendable in 250-hour steps once an oil analysis program supports it. | Cat Natural Gas Engine Oil (NGEO), SAE 40 single-grade only — Caterpillar does not recommend multigrade oils in gas engines. Preferred order of choice: Cat NGEO EL350, then Cat NGEO EL250, then standard Cat NGEO. Sulfated ash is held to 0.40-0.60%; Total Base Number runs roughly 5.6-6.5 depending on the specific grade. SAE 40 covers cold start-up down to about 5°C (41°F) ambient and operation up to 50°C (122°F); below that, an oil heater is recommended. A commercial gas-engine-specific oil that has passed a 7000-hour field evaluation is an acceptable second choice — never substitute a diesel- or gasoline-engine oil. |
| Cooling system (jacket water + aftercooler circuits) | 217.7 L total (57.5 US gal) on the G3516 LE rating, split as jacket water circuit 200.6 L (53 US gal) plus aftercooler (SCAC) circuit 17 L (4.5 US gal). A G3516B LE build runs slightly higher at 221.5 L (58.5 US gal) total. Treat as varies by configuration/series and confirm against the site-specific cooling system sizing sheet for the actual radiator or heat-exchanger package fitted. | Cat Natural Gas Engine Coolant (NGEC), a 50/50 premix of ethylene glycol and water, protects to about -37°C (-34°F). Do not use Cat ELC (Extended Life Coolant) — it is not formulated for gas engines. Acceptable alternates are Cat DEAC or a commercial heavy-duty coolant meeting ASTM D6210, mixed to 100-275 ppm silicates in the 50/50 blend and dosed with the correct Supplemental Coolant Additive. On sour or landfill/digester gas, hold jacket water outlet temperature to a minimum of 110°C (230°F) to limit acid condensation in the crankcase. Service life runs about three years for NGEC or DEAC when properly maintained, shorter for an ASTM-only commercial coolant. |
| Fuel system (natural/gaseous fuel) | No fillable tank. This is a spark-ignited gaseous-fuel engine fed continuously from an external gas supply rather than drawing from an onboard reservoir. | Runs on pipeline natural gas, wellhead/field gas, propane (must meet HD-5 spec with low-compression pistons), or treated bio-gas/digester gas. Minimum methane number 80 for standard engine timing; gas below a methane number of 30 needs pretreatment before use. Typical fuel inlet pressure runs about 35-40 psig on TA-rated builds. Sour gas above roughly 0.43 mg H2S per MJ requires fuel treatment plus the higher jacket water outlet temperature noted above. |
| Grease (general lubrication points) | Not a filled reservoir — applied at generator bearing, linkage, and accessory-drive grease points on the maintenance schedule; no bulk capacity is specified. | Cat Multipurpose Grease, an NLGI 2 lithium-complex grease, covers general-duty points at moderate temperatures. Where a point calls for heavier protection, Cat's gas-engine lubrication guide points to Cat Advanced 3Moly (NLGI 2 with 3% moly) or Cat Ultra 5Moly for severe-duty or high-load joints. Match the grease to each joint's own callout and purge fully when switching types rather than mixing. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar G3516 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
| Every 8,000 h |
|
| Every 20,000 h |
|
| Every 60,000 h |
|
| Every 100,000 h |
|
Servicing the G3516 beyond the schedule
Predictive Maintenance & Fluid Analysis
The G3516's gas-fueled V16 rewards condition monitoring over fixed swaps. Track engine oil samples for silicon, potassium, and sulfur picked up from pipeline or landfill gas fuel streams, and trend cylinder compression and crankcase blowby to catch ring and liner wear early. Log knock and detonation sensor data through the ignition module to spot pre-ignition before it damages pistons. Pair jacket water coolant sampling (additive level, pH) with generator bearing vibration readings to plan downtime around actual wear, not the calendar.
Corrective & Common Repairs
Most unscheduled G3516 downtime traces to the ignition and control side rather than the long block. Coil-on-plug ignition components and detonation sensors degrade with heat cycling and drive erratic timing or unwanted derates. Air/fuel ratio control valves and gas pressure regulators need periodic recalibration to hold lean-burn stability. Jacket water pump seals and heat exchanger or radiator cores foul over time and cause overheating shutdowns. EMCP and ADEM control faults, plus generator-end bearing or winding issues, round out the common repair list.
Overhaul & Rebuild Points
Cat's own service life guidance for the 3500 gas block spans tens of thousands of hours between major work. Expect a top-end overhaul of heads, valves, liners, and rings well before an in-frame overhaul of pistons, rods, and main bearings, with a major overhaul touching the crankshaft and block reserved for well past that on properly maintained units. Turbocharged units also need turbocharger core exchange on its own cycle, and the generator end may need bearing replacement or a rewind at major overhaul.
Seasonal & Environment Servicing
As stationary standby or prime power equipment, the G3516 sees seasonal swings in starting and cooling demand rather than ground conditions. Cold climates need jacket water heaters and reliable air- or battery-start systems kept warm between runs. Hot enclosures need clear radiator or heat exchanger airflow and clean cooling media. Landfill- and digester-gas installations should shorten oil-sample intervals because siloxanes and hydrogen sulfide in the fuel accelerate wear and corrosion compared with pipeline natural gas.
G3516 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 4P-4720 | Filter Element-Fuel | Fuel system service | Check fitment → |
| 134-6307 | Filter Element As-Fuel | Fuel system service | Check fitment → |
| 1D-4540 | Bolt,Machine Fuel Filter Mounting | Fuel system service | Check fitment → |
| 6V-3907 | Seal-O-Ring | Fuel system service | Check fitment → |
| 6I-2507 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
G3516 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| AL1 | High jacket water (coolant) temperature alarm | Overload, dirty radiator or heat exchanger, low coolant, failed water pump, stuck thermostat | Check coolant level and system for blockage or fouling, verify water pump and thermostat operation, confirm sensor reading against a manual gauge |
| AL2 | Low jacket water (coolant) temperature alarm | Jacket water heater failure on a standby unit, thermostat stuck open, cold ambient conditions | Check jacket water heater operation and thermostat, verify temperature sensor and setpoint |
| AL3 | Low engine oil pressure alarm | Low oil level, worn or failing oil pump, clogged oil filter, faulty pressure sensor or wiring | Check oil level and filter condition, verify actual pressure with a mechanical gauge, inspect sensor and connector |
| AL5 | Low engine coolant level fault | Coolant leak, blown hose or gasket, low system fill, faulty coolant level switch | Visually inspect coolant level and check the system for leaks, verify the level switch/sensor operation |
| AL6 | High engine oil temperature fault | Sustained overload, fouled or restricted oil cooler, degraded oil, low oil level | Check oil cooler for fouling and coolant flow, verify oil condition and level, review generator loading |
| AL7 | Generator over voltage fault (protective relay function) | Voltage regulator (AVR) fault or misadjustment, sudden loss of load, incorrect sensing leads | Check AVR settings and sensing connections, verify voltage regulator operation, review recent load changes |
| AL8 | Generator under voltage fault (protective relay function) | Sustained overload, AVR fault, low engine speed affecting output | Check load level against rating, verify AVR operation and sensing leads, confirm engine speed is at rated setpoint |
| AL9 | Generator over frequency fault (engine overspeed condition seen electrically) | Sudden loss of load, governor or actuator fault, incorrect speed setpoint | Check governor and actuator response, verify rated speed setpoint, review load-shedding history |
| AL10 | Generator under frequency fault (engine speed sagging under load) | Overload, restricted fuel gas supply, governor fault, air/fuel ratio control issue | Check load against set rating, verify fuel gas supply pressure, check governor and speed control response |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
G3516 attachments & work tools
Enclosure options
Offered as an open, dead-front skid unit with a lockable access door for indoor engine rooms, or as a factory weatherproof outdoor enclosure. Larger outdoor packages use a walk-in style housing that can carry the remote radiator on the same base skid.
Sound attenuation packages
Weatherproof outdoor enclosures are offered with a sound-attenuation package for noise-sensitive sites; the attenuation level and resulting dBA rating vary by package and measuring distance, so confirm the figure for the ordered enclosure with your dealer. Enclosures in this power class are generally rated for ambient up to roughly 45 deg C (113 deg F), with a cold-weather kit available for sub-freezing sites.
Cooling arrangement
Standard cooling is a skid-mounted jacket-water radiator, with the aftercooler run on its own separate circuit from jacket water. Remote-radiator (radiator on a second skid, piped to the set) and heat-exchanger (site water or cooling-tower loop) arrangements are also offered where enclosure footprint or ambient airflow is limited. A jacket-water heater option keeps standby units at temperature for a fast start.
Control panel / genset control
Earlier-build sets use the EMCP II panel for engine/generator monitoring and start-stop logic, with analog or digital voltage regulation depending on the generator end fitted. Later production is offered with EMCP 4-series digital control (EMCP 4.2/4.3 base, EMCP 4.4 upgrade) adding Ethernet connectivity for remote monitoring and building-management integration.
Paralleling / switchgear
Sets fitted with EMCP 4.4, or the synchronizing-light option on earlier panels, can be paralleled with other gas or diesel generator sets or with utility power through Cat switchgear and paralleling control packages. Several sets can be networked from one control point for load sharing and sequencing in multi-unit plants.
Fuel system / gas configuration
Base fuel setup is tuned for dry pipeline-quality natural gas within a defined heating-value and supply-pressure window, metered through a carburetor, gas pressure regulator, and gas shutoff valve. The same engine platform is also set up for digester gas, landfill gas, or other biogas with lower methane content, with output derated as gas quality drops.
Starting system
Offered with electric starting motor(s) as the standard method, or a pneumatic (air) starting system with its own air lines and silencer for sites without reliable station power or where repeated restart attempts are expected. Dual electric or dual air-start arrangements are available for standby duty where fast, redundant starting matters.
Generator end and base/guarding
The engine block pairs with generator ends across a range of frame sizes and kW/voltage ratings on a common driveline, so alternator size and rated output vary by the generator end ordered. Standard mounting is engine-and-generator support rails on a common structural base with shipping/handling guards; confirm the exact generator frame and control package for a given serial number with a Cat dealer.
All G3516 assemblies by section
Every catalogued assembly group for the Caterpillar G3516. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
130-3884 Accumulator Gp-Turbocharger
| 03***72 | Elbow; (Flared 90 Degree) | 1 |
| 06***56 | Seal-O-Ring | 2 |
| 06***04 | Spacer; (0.459x0.625x1.188-In Thk) | 4 |
9y-3187 Accumulator Gp-Turbocharger
| 06***56 | Seal-O-Ring | 2 |
| 06***04 | Spacer; (0.459x0.625x1.188-In Thk) | 4 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
7w-9828 Adapter Gp-Air Cleaner
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 48 |
| 5N***30 | Gasket | 2 |
| 7W***28 | Adapter Group-Air Cleaner | 1 |
7n-8549 Adapter Gp-Air Cleaner
| 1W***31 | Strip | 8 |
| 1W***32 | Strip | 4 |
| 1W***33 | Strip | 8 |
4p-5698 Aftercooler Gp-Raw Water
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 40 |
| 2D***34 | Bolt-Socket Head; (3/8-16x1-In) | 24 |
| 4P***31 | Bonnet | 1 |
4p-7448 Aftercooler Gp-Raw Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 20 |
| 4P***98 | Aftercooler Group-Raw Water | 1 |
| 4P***48 | Aftercooler Group-Raw Water | 1 |
4p-8950 Aftercooler Gp-Treated Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 72 |
| 15***05 | Gasket | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 16 |
5n-7904 Air Cleaner Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 48 |
| 20***54 | Bolt; (5/8-11x2.5-In) | 6 |
| 20***55 | Bolt; (5/8-11x2.75-In) | 4 |
131-2183 Air Cleaner Gp
| 13***83 | Air Cleaner Group | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 2 |
6i-2593 Air Cleaner Gp
| 6I***07 | Filter Element As-Air | 1 |
| 6I***08 | Filter Element As-Air | 1 |
| 6I***93 | Air Cleaner Group | 1 |
5n-7822 Air Cleaner Gp
| 5N***22 | Air Cleaner Group; -2 Required | 1 |
| 8N***56 | Filter Element As-Air; (Secondary) | 1 |
| 8N***59 | Gasket-Air Cleaner Cover | 1 |
9y-0673 Air Cleaner Gp -Industrial
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 12 |
7w-1037 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 20 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 8 |
8n-3378 Air Cleaner Gp
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
| 2K***73 | Locknut Inside Guard Assembly | 4 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 2 |
4p-9088 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 10 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 8 |
| 13***83 | Air Cleaner Group | 2 |
4w-2915 Air Cleaner Gp
| 13***56 | Precleaner As | 1 |
| 1M***50 | Bowl | 1 |
| 4W***15 | Air Cleaner Group | 1 |
1w-8161 Air Cleaner Gp
| 1W***61 | Air Cleaner Group | 1 |
| 6N***23 | Cup As-Air Cleaner | 1 |
| 6N***44 | Filter Element As-Air; (Secondary)(Secondary) | 1 |
9y-5313 Arrestor Gp-Flame
| 10***74 | Arrestor As, .. Bushing | 1 |
| 15***55 | Gasket-Manifold | 1 |
| 9Y***13 | Arrestor Group-Flame | 1 |
4w-5947 Bypass Gp-Exhaust
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 14***58 | Bypass Group-Exhaust | 1 |
| 16***00 | Locknut; (High Temperature) | 4 |
146-0758 Bypass Gp-Exhaust
| 10***19 | Base As | 1 |
| 11***72 | Diaphragm | 1 |
| 14***51 | Cover As | 1 |
7s-4411 Cap As-Rain -Exhaust Pipe
| 7S***11 | Cap As-Rain; -Exhaust Pipe | 1 |
7c-3824 Cartridge Gp-Turbocharger
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 4 |
| 1P***20 | Ring-Seal | 1 |
| 1S***70 | Nut (.687" O.D.) | 1 |
8n-8487 Elbow Gp-Exhaust
| 1D***66 | Bolt Bracket Assembly To Yoke | 2 |
| 1D***69 | Bolt 107.95 mm(4.25 In.) Long; Bolt (Plate To Front Housing) | 2 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
5n-2458 Elbow-Exhaust
| 5N***58 | Elbow-Exhaust | 1 |
5l-7520 Elbow-Exhaust
| 5L***20 | Elbow-Exhaust | 1 |
5l-6954 Elbow-Exhaust
| 5L***54 | Elbow-Exhaust | 1 |
8l-9859 Elbow-Exhaust
| 8L***59 | Elbow-Exhaust | 1 |
5n-9527 Fitting Gp-Exhaust -Flexible
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 12 |
| 1B***55 | Nut,Plain,Hexagon Turbocharger Mounting | 12 |
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 12 |
7n-6968 Fitting Gp-Exhaust
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 3V***08 | Washer-Hard; (10.2x20.5x2.5-mm Thk)(Shield To Head) | 8 |
| 5L***73 | Gasket-Exhaust Elbow | 1 |
5n-2457 Fitting Gp-Exhaust -Flexible
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 8 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 21***45 | Bellows As | 1 |
7n-6967 Fitting Gp-Exhaust -Flexible
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 24***12 | Gasket; (Exhaust) | 1 |
| 2B***58 | Plug--To Block Upper Front Air Manifold | 1 |
2w-7847 Fitting Gp-Exhaust -Flexible
| 1B***58 | Nut-Full; (5/8-11-Thd) | 4 |
| 2W***47 | Fitting Group-Exhaust; -Flexible | 1 |
| 3N***17 | Adapter As; (Flexible) | 1 |
2w-7871 Flange Gp-Exhaust
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 12 |
| 1B***55 | Nut,Plain,Hexagon Turbocharger Mounting | 12 |
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 12 |
2w-7866 Flange Gp-Exhaust
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 12 |
| 2W***66 | Flange Group-Exhaust | 1 |
| 2W***67 | Flange-Exhaust | 1 |
7n-6962 Flange Gp-Exhaust
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 12 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 12 |
| 7N***54 | Flange | 1 |
2w-7860 Flange Gp-Exhaust
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 6 |
| 2W***60 | Flange Group-Exhaust | 1 |
| 2W***61 | Flange-Exhaust | 1 |
213-1412 Indicator Gp-Air Filter Change
| 21***12 | Indicator Group-Air Filter Change | 1 |
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
4p-9597 Indicator Gp-Air Filter Change
| 3B***85 | Nipple-Pipe | 1 |
| 4P***97 | Indicator Group-Air Filter Change | 1 |
| 4W***20 | Indicator-Air Filter Change | 2 |
7w-1678 Indicator Gp-Air Filter Change
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 4W***20 | Indicator-Air Filter Change | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
7n-6782 Indicator Gp-Air Filter Change
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
| 6I***33 | Indicator Group-Air Filter Change | 2 |
4w-5773 Lines Gp-Aftercooler Air
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 2 |
4p-8350 Lines Gp-Air -Inlet Manifold
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 48 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 12 |
6i-0670 Lines Gp-Air
| 03***51 | Elbow )-Inlet Port To Valve Group | 1 |
| 03***07 | Connector; (Flared) | 1 |
| 6I***70 | Lines Group-Air | 1 |
9y-1223 Lines Gp-Air -Carburetor Inlet
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 4W***25 | Gasket | 1 |
| 4W***26 | Flange | 1 |
5n-8354 Lines Gp-Air -Prelubrication Pump
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 2 |
| 2H***40 | Union 90 Degrees (.50" Ext. Thd.) | 1 |
| 2H***91 | Union --Block To Hose Assembly; -- Block To Hose Assembly | 1 |
116-9850 Lines Gp-Turbocharger Vent
| 00***81 | Tee-Union; (Flared 37-Deg) | 1 |
| 01***24 | Bushing To Supply Port | 2 |
| 03***45 | Reducer-Flared | 1 |
7e-1822 Manifold Gp-Exhaust
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 32 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***19 | Plug-Cup | 2 |
4w-2516 Manifold Gp-Exhaust
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 32 |
| 1A***60 | Capscrew, Hex Head (1/2 - 13 X 2 G5); (Hex Head) (1/2-13x2 Gd 8 Z) | 8 |
| 1D***06 | Bolt; (3/8-16x6-In)(Locations Y) | 32 |
4w-6341 Mounting Gp-Air Cleaner
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 1K***49 | Spacer Alternator To Brackets | 1 |
206-7137 Mounting Gp-Air Cleaner
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 1K***49 | Spacer Alternator To Brackets | 1 |
2w-4072 Muffler
| 2W***72 | Muffler | 1 |
141-7047 Muffler
| 14***47 | Muffler | 1 |
2w-4075 Muffler
| 2W***75 | Muffler | 1 |
152-0596 Muffler Gp-Spark Arrestor
| 15***96 | Muffler Group-Spark Arrestor | 1 |
124-3237 Precleaner Gp -Air Cleaner
| 12***37 | Precleaner As; -Air Cleaner-Air Inlet | 1 |
| 5P***99 | Clamp; (Hose) | 1 |
| 6H***21 | Body-Pre-Cleaner | 1 |
5n-7831 Precleaner Gp
| 2M***79 | Seal-O-Ring | 1 |
| 5N***31 | Precleaner Group | 1 |
| 5N***33 | Body As | 1 |
4w-2890 Precleaner Gp -Air Cleaner
| 12***37 | Precleaner As; -Air Cleaner-Air Inlet | 1 |
| 4W***90 | Precleaner Group; -Air Cleaner | 1 |
| 4W***49 | Pipe As-Air Inlet | 1 |
7c-3821 Turbocharger Gp
| 1B***74 | Plug,Pipe Base Assembly,Engine Oil Filter Assembly | 7 |
| 4W***36 | Housing As-Turbine; (Turbine) | 1 |
| 7C***21 | Turbocharger Group | 1 |
7w-5268 Turbocharger Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 12***36 | Gasket; (Turbocharger) | 2 |
| 16***00 | Locknut; (High Temperature) | 8 |
4w-5424 Valve Gp-Air Control
| 2W***20 | Valve-Control | 1 |
| 32***82 | Knob | 1 |
| 4W***24 | Valve Group-Air Control; (Engine Start Control) | 1 |
8n-8483 Valve Gp-Air Control -Rh
| 1L***73 | Valve Group-Pressure Reducing; -Rh | 1 |
| 3L***93 | Nipple-Close; (1 1/2-11 1/2 Npt Thd) | 1 |
| 5B***66 | Elbow; (90 Degree, 1-1/2-11-1/2 Npt) | 1 |
Basic Engine
5r-7425 Barring Gp -Lh
| 3R***37 | Device-Barring | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
| 5R***25 | Barring Group; Barring Group-Engine | 1 |
253-2468 Barring Gp -Rh
| 25***68 | Barring Group; -Rh | 1 |
| 3R***37 | Device-Barring | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
4p-8347 Camshaft Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 4N***50 | Dowel; (1.25in X .376in) | 2 |
4p-8352 Camshaft Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 4N***50 | Dowel; (1.25in X .376in) | 2 |
5n-3765 Coupling Gp-Flexible -Viscous Dampened
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 12 |
| 1A***37 | Bolt Clutch Assembly To Bracket (Fan Support) | 12 |
| 3N***66 | Coupling-Drive | 1 |
247-0308 Coupling Gp-Flexible -Generator
| 24***91 | Coupling; (Outer) | 1 |
| 24***08 | Coupling Group-Flexible; -Generator | 1 |
| 24***32 | Washer; (17x30x3-mm Thk) | 12 |
268-6475 Coupling Gp-Flexible -Generator
| 24***08 | Coupling Group-Flexible; -Generator | 1 |
| 26***75 | Coupling Group-Flexible; -Generator | 1 |
| 4M***53 | Washer-Hard; (24x38x3.5-mm Thk) | 8 |
8n-7152 Coupling Gp-Flexible
| 1D***85 | Cap Screw (3 1/4" Long) | 12 |
| 5N***78 | Plate As | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
9y-6123 Cover Gp-Cylinder Block -Central Structure
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 84 |
225-7845 Cover Gp-Engine Lifting Eye
| 22***45 | Cover Group-Engine Lifting Eye | 1 |
| 22***46 | Cover-Lifting Eye | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 1 |
226-1771 Cover Gp-Engine Lifting Eye
| 22***71 | Cover Group-Engine Lifting Eye | 1 |
| 22***81 | Cover-Lifting Eye | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 1 |
4w-1528 Cover Gp-Flywheel Housing
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 36 |
4p-8309 Cover Gp-Flywheel Housing
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
4p-8306 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 14 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 3 |
| 2A***20 | Plug-Drain; (Front Housing) | 3 |
4p-8304 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 24 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 23***46 | Seal-O-Ring | 1 |
4w-4839 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 34 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 1C***51 | Bolt--Installation Of 2v***26 Retainer | 1 |
2w-5616 Cover Gp-Oil Pan
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***64 | Cover As | 1 |
| 2W***16 | Cover Group-Oil Pan | 1 |
4w-1122 Cover Gp-Rear Housing
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 7 |
| 25***74 | Gasket | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 2 |
4p-8310 Cover Gp-Valve Mechanism
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 27***57 | Seal; (Valve Cover To Breather) | 1 |
| 4P***10 | Cover Group-Valve Mechanism | 1 |
226-1781 Cover-Lifting Eye
| 22***81 | Cover-Lifting Eye | 1 |
225-7846 Cover-Lifting Eye
| 22***46 | Cover-Lifting Eye | 1 |
8n-0337 Crankshaft Gp
| 12***45 | Bolt As; (5/8-18x4.25-In)(Counterweight) | 48 |
| 12***88 | Crankshaft As | 1 |
| 14***31 | Bearing As-Main; (Standard) | 9 |
106-2780 Cylinder Block As
| 10***80 | Cylinder Block As | 1 |
| 22***96 | Cap-Crankshaft Bearing | 9 |
| 4W***13 | Plug; (2-1/4-12 Thd) | 4 |
101-1173 Cylinder Block As
| 10***73 | Cylinder Block As | 1 |
| 21***26 | Liner-Cylinder Block | 16 |
| 22***96 | Cap-Crankshaft Bearing | 9 |
115-5160 Cylinder Block Gp
| 03***42 | Seal-O-Ring; (11.89mm Id) | 6 |
| 10***80 | Cylinder Block As | 1 |
| 11***60 | Cylinder Block Group | 1 |
115-5159 Cylinder Block Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 2 |
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 16 |
| 10***73 | Cylinder Block As | 1 |
4p-6571 Cylinder Head As
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 5 |
| 3B***45 | Plug Flywheel Housing Turbocharger Drain Hole | 5 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 2 |
4p-8300 Cylinder Head As
| 4P***71 | Cylinder Head As | 1 |
| 4P***00 | Cylinder Head As | 1 |
| 7N***02 | Dowel | 2 |
4p-6570 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 4 |
| 13***14 | Rotocoil As | 4 |
| 2A***29 | Lock,Valve Spring R Cylinder Head | 8 |
206-1555 Cylinder Head Gp
| 19***60 | Insert-Valve Seat; (Exhaust)(Standard) | 2 |
| 20***46 | Insert-Valve Seat; (Exhaust 0.254-mm Os Od) | 0 |
| 20***47 | Insert-Valve Seat; (Exhaust 0.508-mm Os Od) | 0 |
206-1556 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 2 |
| 19***66 | Guide-Valve; (Inlet)(Standard) | 2 |
| 19***99 | Rotocoil As | 4 |
206-1558 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 13***20 | Fastener Group-Cylinder Head | 6 |
| 13***21 | Fastener Group-Cylinder Head | 2 |
4p-6569 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 12***12 | Seal-Water; (11.2mm Id) | 4 |
| 12***13 | Seal-Water; (21.2mm Id) | 4 |
8n-7182 Damper Gp
| 19***88 | Damper As | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 10 |
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
4w-0278 Damper Gp
| 19***88 | Damper As | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 10 |
| 3B***15 | Bolt Guard Assembly To Accessory Drive Housing | 18 |
202-8640 Drain Gp-Engine Oil -Rear
| 20***40 | Drain Group-Engine Oil; -Rear | 1 |
| 3B***70 | Nipple,Pipe Hose To Flange | 1 |
| 3B***45 | Nipple-Pipe; (3/4-14 Npt Thd)(Both Ends) | 1 |
110-6206 Drain Gp-Engine Oil
| 11***06 | Drain Group-Engine Oil | 1 |
| 11***07 | Valve; (Engine Oil Drain) | 1 |
| 3B***96 | Fitting; (Nipple) | 1 |
9y-7876 Drain Gp-Engine Oil -Pan
| 1F***60 | Nipple-Pipe | 1 |
| 3E***30 | Plug-Pipe; (3/4-14 Nptf) | 1 |
| 6F***68 | Gasket; (Oil Pan) | 1 |
7n-4871 Drive Gp-Accessory -Upper, Rh
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 2 |
1w-9553 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
| 11***65 | Bearing | 1 |
8n-9166 Drive Gp-Accessory -Upper, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 12***00 | Bearing-Sleeve | 2 |
8n-5678 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
3n-8647 Fastener Gp-Coupling
| 20***99 | Bolt-12 Point Head; (7/8-9x3-In) | 8 |
| 3N***47 | Fastener Group-Coupling; Fastener Group--Shaft And Hub | 1 |
| 8C***13 | Washer-Hard; (24x41.5x4-mm Thk) | 8 |
2w-8772 Flywheel Gp
| 23***43 | Gear-Flywheel; (183-Teeth) | 1 |
| 24***19 | Flywheel As | 1 |
| 2W***72 | Flywheel Group | 1 |
122-9281 Gear Gp-Front -Low Speed, Standard Rotation
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
112-5674 Gear Gp-Rear -Cam Drive
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 10***65 | Plate-Thrust | 1 |
| 10***68 | Washer-Thrust; (19.50 X 106 X 1.9mm Thk) | 2 |
7w-5780 Guard Gp-Belt -Alternator
| 27***35 | Spacer; (13.87x21.34x11-mm Thk) | 2 |
| 28***74 | Guard As-Alternator | 1 |
| 7W***80 | Guard Group-Belt; -Alternator | 1 |
151-9228 Guard Gp-Belt -Alternator
| 15***28 | Guard Group-Belt; -Alternator | 1 |
| 17***59 | Guard As-Belt; (Alternator) | 1 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 1 |
3n-5765 Guard Gp-Coupling -Flywheel
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 10 |
| 1V***23 | Plate | 2 |
7w-6669 Guard Gp-Damper
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 3 |
| 2D***35 | Locknut (Visor To Bracket) | 3 |
| 6V***46 | Washer-Hard; (7.2x25x2-mm Thk) | 9 |
8n-9639 Guard Gp-Damper
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 6 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 8 |
4p-8307 Housing Gp-Flywheel
| 1A***69 | Bolt (R.H. Side Flywheel Housing) | 2 |
| 1D***90 | Bolt 4.75 In.(120.65 mm) Long | 16 |
| 22***19 | Housing-Flywheel | 1 |
7w-1530 Housing Gp-Front
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 10***32 | Housing-Front Drive | 1 |
| 1D***93 | Bolt 5.5 In. (13.97 cm) Long | 10 |
7w-3724 Housing Gp-Front -Accessory Drive
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 10***34 | Housing-Accessory Drive | 1 |
| 1D***93 | Bolt 5.5 In. (13.97 cm) Long | 10 |
3n-5596 Hub-Flexible Coupling
| 3N***96 | Hub-Flexible Coupling | 1 |
4w-5450 Lifting Gp-Engine
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 4 |
| 15***26 | Bracket As | 2 |
| 4W***50 | Lifting Group-Engine | 1 |
7e-4836 Mounting Gp-Alternator
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 14***16 | Belt-Serpentine; (Alternator) | 1 |
| 1A***68 | Bolt 7.50 In. (19.05 cm) Long | 1 |
5n-8877 Mounting Gp-Engine Flexible
| 15***64 | Mount As | 8 |
| 5N***77 | Mounting Group-Engine Flexible | 1 |
| 5P***97 | Washer; (17x45x6-mm Thk) | 8 |
9y-3082 Pan Gp-Oil
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
7c-4711 Pan Gp-Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 18 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 50 |
7c-7178 Pan Gp-Oil -Deep Sump
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 18 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 50 |
9y-3085 Pan Gp-Oil -Deep Sump
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
7e-7580 Piston & Rod Gp
| 10***30 | Bearing-Connecting Rod; (Standard) | 0 |
| 10***31 | Bearing-Connecting Rod; (0.63-mm Us Id) | 0 |
| 10***32 | Bearing-Connecting Rod; (1.27-mm Us Id) | 0 |
8n-6564 Pulley As-Crankshaft
| 4W***35 | Kit-Bushing; (Crankshaft Pulley) | 1 |
| 8N***64 | Pulley As-Crankshaft | 1 |
7n-4106 Pulley As-Crankshaft
| 4W***35 | Kit-Bushing; (Crankshaft Pulley) | 1 |
| 7N***06 | Pulley As-Crankshaft | 1 |
7w-3813 Seal Gp-Crankshaft
| 11***32 | Seal Group-Crankshaft; (Cw Rotation) | 1 |
| 11***33 | Seal Group-Crankshaft; (Ccw Rotation) | 1 |
| 7W***13 | Seal Group-Crankshaft | 1 |
7n-7660 Drive Gp-Fan
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
| 7N***57 | Shaft-Stub | 1 |
| 7N***60 | Shaft Group-Stub; -Crankshaft Pulley | 1 |
150-7947 Shaft Gp-Stub
| 14***83 | Shaft-Stub | 1 |
| 15***47 | Shaft Group-Stub | 1 |
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
8n-8510 Valve Gp-Explosion Relief
| 27***59 | Seal | 2 |
| 2W***84 | Kit-Repair; (Explosion Relief)(Crankcase) | 1 |
| 8N***09 | Valve Group-Explosion Relief; (Crankcase) | 2 |
1w-8465 Valve Mechanism Gp
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 12***81 | Bridge As | 2 |
| 13***49 | Base As | 1 |
Cooling System
4p-3531 Connection Gp-Water -Aftercooler
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 8 |
| 4P***32 | Elbow | 1 |
| 4P***33 | Elbow | 1 |
8n-8993 Connection Gp-Water -Inlet, Lh
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 16 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 1S***72 | Gasket | 2 |
7w-6372 Connection Gp-Water -Outlet
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
120-3951 Connection Gp-Water
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
4p-7072 Connection Gp-Water -Outlet, Lh
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
9y-8179 Connection Gp-Water -Inlet, Outlet
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
4w-5891 Cooler Gp-Engine Oil
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
| 10***32 | Seal-O-Ring | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
6i-0999 Flange Gp-Coolant Lines
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 1S***72 | Gasket | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 8 |
7n-4885 Switch Gp-Coolant Level
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 2 |
| 2N***68 | Switch-Liquid Level; (Coolant) | 1 |
| 3N***22 | Hose Assem. 29.6 cm(11.65 In.) | 2 |
150-0372 Housing & Regulator Gp -Coolant
| 15***72 | Housing & Regulator Group; -Coolant | 1 |
| 15***17 | Regulator As-Water Temperature; (110-Deg F) | 1 |
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
7w-1497 Housing & Regulator Gp -Coolant
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 1 |
| 4P***03 | Housing-Upper | 1 |
9y-9090 Housing & Regulator Gp -Outlet Control
| 11***74 | Valve As-Vent Line | 1 |
| 15***10 | Seal-Integral; (Water Temperature Regulator) | 1 |
| 24***33 | Regulator-Water Temperature; (98-Deg C)(Water, Coolant) | 4 |
7w-6555 Housing & Regulator Gp -Coolant
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 1 |
| 4P***03 | Housing-Upper | 1 |
5p-9130 Joint As-Tube
| 5P***30 | Joint As-Tube | 1 |
| 9X***40 | Seal; (140.46mm Id) | 2 |
2w-1441 Lines Gp-Auxiliary Fresh Water
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
4p-3530 Lines Gp-Auxiliary Fresh Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 8 |
7e-0008 Lines Gp-Water -Oil Cooler
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
1n-4421 Lines Gp-Water -Lower
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
7e-3887 Lines Gp-Water -Upper
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
128-7361 Lines Gp-Water -Upper
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 37 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 30 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
129-8217 Lines Gp-Water -Upper
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 43 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 30 |
| 11***76 | Manifold; (Rear, Lh) | 1 |
2w-1437 Lines Gp-Water -Upper
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 34 |
133-3689 Lines Gp-Water -Manifold
| 00***62 | Seal-O-Ring; (63.17mm Id) | 1 |
| 03***69 | Elbow-Flared; (1/2-14 Nptf) | 2 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 2 |
4w-5771 Lines Gp-Water -Turbocharger Exhaust
| 00***04 | Fitting-Flared | 2 |
| 00***42 | Elbow | 2 |
| 00***25 | Elbow-Flared | 1 |
9y-9185 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
4p-8354 Lines Gp-Water -Upper
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 34 |
7e-9781 Pump Gp-Auxiliary Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
1w-9554 Pump Gp-Auxiliary Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 7 |
| 1T***65 | Bolt 2.54 cm (1" Long) | 1 |
| 1W***54 | Pump Group-Auxiliary Water; -Fresh Water | 1 |
291-4313 Pump Gp-Auxiliary Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***79 | Shaft; (14-Teeth) | 1 |
212-8169 Pump Gp-Auxiliary Water -Fresh Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***69 | Pump Group-Auxiliary Water; -Fresh Water | 1 |
2w-9729 Pump Gp-Water
| 16***78 | Pump Group-Water; -Jacket Water | 1 |
| 1H***78 | Seal-O-Ring | 1 |
| 2W***29 | Pump Group-Water; Water Pump Group | 1 |
212-8177 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
7e-0011 Pump Gp-Water
| 16***79 | Pump Group-Water | 1 |
| 1H***78 | Seal-O-Ring | 1 |
| 3B***15 | Bolt Guard Assembly To Accessory Drive Housing | 4 |
166-4378 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
212-8173 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
166-4379 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 0 |
8n-7643 Housing & Regulator Gp -Inlet Control
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 5 |
| 10***12 | Plate | 2 |
| 1A***83 | Bolt (4.75" Long-Location "B") | 5 |
7w-1427 Regulator Gp-Temperature
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
4p-4333 Tank Gp-Expansion
| 20***25 | Tank Group-Expansion | 1 |
| 2W***37 | Lines Group-Water; -Upper | 1 |
| 4P***33 | Tank Group-Expansion | 1 |
201-3425 Tank Gp-Expansion
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 11***74 | Valve As-Vent Line | 1 |
129-8218 Tank Gp-Expansion
| 12***61 | Lines Group-Water; -Upper | 1 |
| 12***18 | Tank Group-Expansion | 1 |
| 20***25 | Tank Group-Expansion | 1 |
113-9480 Tank Gp-Water
| 06***37 | Union-Flared | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 8 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 14 |
Electrical And Starting System
7c-2700 Control Gp-Manual Voltage
| 7C***00 | Module-Control | 1 |
6n-9294 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 5 |
| 11***19 | Diode As-Alternator | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
266-7227 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
112-3454 Alternator Gp-Charging
| 11***54 | Alternator Group-Charging | 1 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
| 6N***94 | Alternator Group; (24-Volt, 35-Ampere) | 1 |
4n-3986 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
| 10***62 | Kit-Alternator Terminal | 1 |
7n-7981 Alternator Gp-Charging
| 09***19 | Washer; (7.14x15.88x1.58-mm Thk) | 2 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
| 2N***79 | Machine Screw--Wire Assembly To Panel | 1 |
112-3455 Alternator Gp-Charging
| 09***19 | Washer; (7.14x15.88x1.58-mm Thk) | 2 |
| 11***55 | Alternator Group-Charging | 1 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
331-5717 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
7w-0408 Battery Charger
| 7W***08 | Battery Charger; Battery Charger--24 Volt Dc | 1 |
131-0832 Battery Charger Gp
| 13***32 | Battery Charger Group | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
| 13***74 | Fuse; (15-Ampere) | 1 |
7l-7872 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
7l-7871 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
115-2513 Box Gp-Extension Terminal -Circuit Breaker
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 10 |
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***34 | Cover As-Top | 1 |
195-0376 Box Gp-Junction
| 19***76 | Box Group-Junction | 1 |
| 4P***83 | Box Group-Junction | 1 |
4p-5283 Box Gp-Junction
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 2N***74 | Screw; (6-32x0.375-In) | 1 |
| 2N***75 | Screw; (6-32x0.5-In) | 1 |
252-7458 Bus Bar As
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 6 |
| 20***43 | Bolt; (M12x1.75x42.5-mm) | 12 |
| 25***58 | Bus Bar As | 1 |
122-0332 Cable Gp -Circuit Breaker Connection
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 24 |
| 12***32 | Cable Group; -Circuit Breaker Connection | 1 |
7w-0825 Cable Gp-Battery
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 1 |
| 1S***51 | Terminal-Cable; (00-Ga, 1/2-In Screw) | 2 |
252-7534 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***30 | Circuit Breaker Group | 1 |
252-7539 Circuit Breaker & Mounting Gp
| 10***97 | Bar-Circuit Breaker; (3200-Ampere) | 2 |
| 10***16 | Bar-Circuit Breaker; (3200-Ampere) | 3 |
| 10***18 | Bar-Circuit Breaker; (3200-Ampere) | 1 |
252-7537 Circuit Breaker & Mounting Gp
| 25***31 | Circuit Breaker Group | 1 |
| 25***37 | Circuit Breaker & Mounting Group | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 18 |
252-7538 Circuit Breaker & Mounting Gp
| 25***32 | Circuit Breaker Group | 1 |
| 25***38 | Circuit Breaker & Mounting Group | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 24 |
7c-0230 Circuit Breaker As
| 5N***57 | Circuit Breaker 1200 Amperes Derated | 1 |
| 7C***30 | Circuit Breaker As | 1 |
270-4537 Circuit Breaker As -1200-Ampere
| 24***30 | Kit-Bolt; (Circuit Breaker) | 1 |
| 24***27 | Fastener Group; (Bus Bar Box) | 3 |
| 24***47 | Terminal-Circuit Breaker | 1 |
7c-0229 Circuit Breaker As
| 3N***85 | Circuit Breaker 1200 Amperes Derated | 1 |
| 7C***29 | Circuit Breaker As | 1 |
4p-3841 Circuit Breaker As
| 4P***41 | Circuit Breaker As | 1 |
| 4P***43 | Circuit Breaker As; (1600-Ampere) | 1 |
4p-3840 Circuit Breaker As
| 4P***40 | Circuit Breaker As | 1 |
| 4P***42 | Circuit Breaker As; (1600-Ampere) | 1 |
105-7934 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
105-7933 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***33 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
7c-0228 Circuit Breaker As
| 5N***58 | Circuit Breaker 1000 Amperes Derated | 1 |
| 7C***28 | Circuit Breaker As | 1 |
7c-0227 Circuit Breaker As
| 3N***84 | Circuit Breaker 1000 Amperes Derated | 1 |
| 7C***27 | Circuit Breaker As | 1 |
207-1740 Circuit Breaker Gp
| 10***26 | Circuit Breaker Group | 1 |
| 20***40 | Circuit Breaker Group | 1 |
252-7530 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***30 | Circuit Breaker Group | 1 |
| 27***58 | Circuit-Breaker; (1600-Ampere) | 1 |
252-7532 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***32 | Circuit Breaker Group | 1 |
| 27***60 | Circuit Breaker As; (2500-Ampere) | 1 |
106-5663 Circuit Breaker Gp
| 10***34 | Circuit Breaker Group; (1000-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***63 | Circuit Breaker Group | 1 |
106-5664 Circuit Breaker Gp
| 10***35 | Circuit Breaker Group; (1200-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***64 | Circuit Breaker Group | 1 |
105-7926 Circuit Breaker Gp
| 10***26 | Circuit Breaker Group | 1 |
| 10***33 | Circuit Breaker As | 1 |
| 10***05 | Bar; (1600-Ampere) | 3 |
114-4674 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 11***74 | Circuit Breaker Group | 1 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 9 |
252-7533 Circuit Breaker Gp
| 25***57 | Bus As; (3200-Ampere) | 2 |
| 25***29 | Circuit Breaker As; (3200-Ampere) | 1 |
| 25***33 | Circuit Breaker Group | 1 |
265-4713 Circuit Breaker Gp
| 24***61 | Shunt-Trip | 1 |
| 26***13 | Circuit Breaker Group | 1 |
270-4658 Circuit Breaker Gp
| 10***95 | Bar As | 2 |
| 10***96 | Bar As | 1 |
| 27***37 | Circuit Breaker As; -1200-Ampere | 1 |
105-7927 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 10***32 | Switch As-Auxiliary | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
106-5661 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***61 | Circuit Breaker Group | 1 |
| 10***67 | Circuit Breaker As; (1200-Ampere) | 1 |
7w-9640 Circuit Breaker Gp
| 3K***06 | Screw-Machine-Relay To Bracket | 2 |
| 4B***63 | Washer; (4.7x11x1.2-mm Thk) | 2 |
| 6T***45 | Circuit Breaker Group; -60-Ampere | 1 |
252-7531 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***31 | Circuit Breaker Group | 1 |
| 27***59 | Circuit-Breaker; (2000-Ampere) | 1 |
106-5659 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***59 | Circuit Breaker Group | 1 |
| 10***65 | Circuit Breaker As; (800-Ampere) | 1 |
106-5660 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***60 | Circuit Breaker Group | 1 |
| 10***66 | Circuit Breaker As; (1000-Ampere) | 1 |
105-7928 Circuit Breaker Gp
| 10***28 | Circuit Breaker Group | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***99 | Bar-Circuit Breaker | 3 |
103-8974 Connection Gp-Electrical
| 10***74 | Connection Group-Electrical | 1 |
| 10***80 | Film-Identification; (Terminal Marker) | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 20 |
4p-4634 Connection Gp-Electrical
| 03***43 | Screw; (1/4-20x0.625-In) | 2 |
| 17***97 | Strip Group-Terminal; -Ac | 1 |
| 2N***80 | Screw-Machine; (10-24x0.75-In) | 2 |
108-0726 Connection Gp-Electrical
| 10***26 | Connection Group-Electrical | 1 |
| 10***80 | Film-Identification; (Terminal Marker) | 1 |
| 2F***47 | Screw-Machine | 6 |
7c-6795 Connection Gp-Electrical
| 2F***47 | Screw-Machine | 6 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 30 |
| 4D***60 | Strip-Terminal; 21.4cm(8.44in)Lg | 3 |
5n-2126 Connector -Thermocouple
| 5N***26 | Connector; Adapter-.25in Pipe Thread | 1 |
237-1971 Contactor Gp-Generator -Jacket Water Heater
| 23***71 | Contactor Group-Generator; -Jacket Water Heater | 1 |
| 23***24 | Contactor | 1 |
4p-9565 Control & Cover Gp-Eng Elek
| 00***40 | Connector; (Flared) | 1 |
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 03***39 | Seal-O-Ring (Id=9.25mm) | 1 |
121-5502 Control Gp-Engine Electronic
| 12***24 | Bracket As | 4 |
| 12***02 | Control Group | 1 |
| 13***11 | Junction Box | 1 |
7c-0330 Control Gp-Air Starting
| 2V***56 | Hose Assem. 53.4 cm (21.02 In.) | 1 |
| 4M***17 | Bushing-Reducing; (For Use With Ta Exhaust Man.) | 1 |
| 5F***34 | Valve As-Vent; (Governor Air Compressor) | 1 |
4w-7209 Control Gp-Air Starting -Lh
| 06***95 | Elbow (Between Fuel Lines) | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
147-8337 Control Gp-Air Starting
| 13***77 | Valve Group-Solenoid; -Air Start-Air Starting | 1 |
| 14***37 | Control Group-Air Starting | 1 |
| 2V***56 | Hose Assem. 53.4 cm (21.02 In.) | 1 |
4w-7203 Control Gp-Air Starting -Rh
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
154-3853 Control Gp-Air Starting
| 14***37 | Control Group-Air Starting | 1 |
| 15***53 | Control Group-Air Starting | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
5n-0591 Control Gp-Manual Voltage
| 5N***91 | Control Group-Electronic | 1 |
| 5N***03 | Varistor As | 1 |
| 5N***05 | Plate-Switch | 1 |
9y-6496 Module Gp-Interface
| 6V***75 | Track-Relay; (34-cm) | 0 |
| 6V***87 | Screw-Pan Head; (10-24x1-In) | 2 |
| 8K***44 | Fuse; (1-Ampere) | 10 |
4p-8890 Control Gp-Engine Electronic
| 4P***90 | Control Group-Engine Electronic | 1 |
| 4P***65 | Control & Cover Group-Eng Elek | 1 |
| 4P***75 | Wiring Group-Engine | 1 |
205-0628 Control Gp-Engine Electronic
| 10***87 | Bolt; (M5x0.8x12-mm) | 2 |
| 20***28 | Control Group-Engine Electronic | 1 |
| 2H***15 | Washer; (0.219x0.41x0.031-In Thk) | 4 |
132-4370 Control Gp-Engine Electronic
| 13***70 | Control Group-Engine Electronic | 1 |
| 16***34 | Module Group-System Communication | 1 |
109-7034 Control Gp-Jacket Water Heater
| 10***34 | Control Group-Jacket Water Heater | 1 |
| 3E***64 | Switch Group-Temperature; -Coolant | 1 |
| 3T***48 | Clip Assembly - Housing Plug To Housing Recp. | 1 |
158-6172 Conversion Ar
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
| 15***72 | Conversion Ar | 1 |
120-6124 Conversion Ar
| 11***58 | Lines Group-Engine Oil | 1 |
| 12***51 | Connection Group-Water | 1 |
| 12***24 | Conversion Ar | 1 |
129-8220 Conversion Ar
| 11***58 | Lines Group-Engine Oil | 1 |
| 12***51 | Connection Group-Water | 1 |
| 12***17 | Lines Group-Water; -Upper | 1 |
158-6171 Conversion Ar
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
| 15***71 | Conversion Ar | 1 |
116-8752 Harness As-Panel -Eis, Interconnect
| 11***52 | Harness As-Panel; -Eis, Interconnect | 1 |
118-0474 Harness As-Panel -Eis, Interconnect
| 11***74 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8755 Harness As-Panel -Eis, Interconnect
| 11***55 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8756 Harness As-Panel -Eis, Interconnect
| 11***56 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8753 Harness As-Panel -Eis, Interconnect
| 11***53 | Harness As-Panel; -Eis, Interconnect | 1 |
122-6072 Harness As-Panel -Eis, Interconnect
| 12***72 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8754 Harness As-Panel -Eis, Interconnect
| 11***54 | Harness As-Panel; -Eis, Interconnect | 1 |
242-9752 Harness As-Power -Digital Voltage Regulator
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Terminal As-Ring | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
243-5282 Harness As-Sensor -Exhaust
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 8 |
| 15***22 | Seal; (70mm Od) | 1 |
5n-9366 Harness As-Thermocouple
| 5N***66 | Harness As-Thermocouple; Lead Assembly-See Pyrometer Chart | 1 |
240-6833 Harness As-Wiring -Ignition, Lh
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
242-3100 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 24 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***66 | Wedge-Plug Lock; (3-Pin) | 1 |
129-1626 Harness As-Wiring
| 12***26 | Harness As-Wiring | 1 |
209-7551 Harness As-Wiring -Shunt Trip
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 2 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
243-4271 Harness As-Wiring -Generator Terminal Strip
| 23***56 | Plug-Connector; (6-Pin) | 1 |
| 23***57 | Plug-Connector; (9-Pin) | 1 |
| 23***58 | Plug-Connector; (12-Pin) | 1 |
130-4618 Harness As-Wiring -Rectifier
| 13***18 | Harness As-Wiring; -Rectifier | 1 |
107-7542 Harness As-Wiring -Eis
| 10***42 | Harness As-Wiring; -Eis | 1 |
| 12***26 | Harness As-Wiring | 1 |
| 12***29 | Harness As-Wiring | 1 |
129-1629 Harness As-Wiring
| 12***29 | Harness As-Wiring | 1 |
129-1632 Harness As-Wiring
| 12***32 | Harness As-Wiring | 1 |
242-3104 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 22 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
240-6834 Harness As-Wiring -Emcp Ii
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 10 |
| 24***34 | Harness As-Wiring; -Emcp Ii | 1 |
7e-6248 Heater Gp-Jacket Water
| 10***32 | Thermostat; (60 Deg F To 160 Deg F)(Jacket Water Heater) | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
7e-6247 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 7E***47 | Heater Group-Jacket Water | 1 |
200-6504 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 20***04 | Heater Group-Jacket Water | 1 |
279-6642 Heater Gp-Jacket Water
| 27***42 | Heater Group-Jacket Water | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
4p-7489 Ignition Gp-Gas Engine
| 03***43 | Screw; (1/4-20x0.625-In) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 1 |
126-5667 Ignition Gp-Gas Engine
| 03***43 | Screw; (1/4-20x0.625-In) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 1 |
8n-8481 Lines Gp-Air Starting
| 11***84 | Lubricator Group-Air Motor | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 2L***11 | Nipple (L.H. Mounting) | 2 |
8n-8489 Lines Gp-Air Starting -Rh
| 00***33 | Tee-Pipe | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
245-9933 Lines Gp-Air Starting
| 11***84 | Lubricator Group-Air Motor | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 24***33 | Lines Group-Air Starting | 1 |
119-6284 Lubricator Gp-Air Motor
| 11***82 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 11***83 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 11***84 | Lubricator Group-Air Motor | 1 |
7w-0522 Lubricator Gp-Air Motor
| 15***45 | Valve-Needle | 1 |
| 15***46 | Gauge-Sight; (Lubricant)(Fluid Level) | 1 |
| 15***47 | Tube-Glass | 1 |
119-6282 Lubricator Gp-Air Motor
| 11***82 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 6N***84 | Gasket | 1 |
| 6N***85 | Plug-Filler | 2 |
119-6283 Lubricator Gp-Air Motor
| 11***83 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
106-7708 Mounting Gp-Circuit Breaker
| 10***17 | . Axle, Bracket As | 1 |
| 10***08 | Mounting Group-Circuit Breaker | 1 |
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
7c-0266 Mounting Gp-Circuit Breaker
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 5P***81 | Seal 1.334 M(53.50 In.) | 0 |
7c-2206 Mounting Gp-Circuit Breaker
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 5P***81 | Seal 1.334 M(53.50 In.) | 0 |
252-7525 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 25***21 | Support | 2 |
| 25***22 | Panel | 1 |
106-7709 Mounting Gp-Circuit Breaker
| 10***17 | . Axle, Bracket As | 1 |
| 10***09 | Mounting Group-Circuit Breaker | 1 |
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
122-3488 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***88 | Mounting Group-Circuit Breaker | 1 |
| 12***29 | Bracket | 1 |
6i-1044 Mounting Gp-Jacket Wtr Heater -Rh
| 03***76 | Elbow-To Hose As. | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 3 |
| 1K***37 | Elbow-Pipe | 1 |
266-4317 Mounting Gp-Jacket Wtr Heater -Lh
| 00***62 | Elbow-External Pipe Thread | 1 |
| 09***19 | Plug-Pipe | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
6i-1043 Mounting Gp-Jacket Wtr Heater -Lh
| 00***35 | Elbow-External Pipe Thread | 1 |
| 05***58 | "P" Clip | 6 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
4p-2454 Mounting Gp-Transformer
| 12***74 | Clip-Loop; (12.7mm Id) | 1 |
| 4P***54 | Mounting Group-Transformer | 1 |
| 6K***06 | Strap-Cable -Lines From Rotate Valve | 3 |
106-7696 Panel As-Box -Circuit Breaker
| 10***18 | Panel-Circuit Breaker | 1 |
| 10***96 | Panel As-Box; -Circuit Breaker | 1 |
| 7W***91 | Seal (104 cm) | 0 |
106-7695 Panel As-Box -Circuit Breaker
| 10***19 | Panel-Circuit Breaker | 1 |
| 10***95 | Panel As-Box; -Circuit Breaker | 1 |
| 7W***91 | Seal (104 cm) | 0 |
9y-8441 Panel As-Box
| 7W***91 | Seal (104 cm) | 0 |
| 9Y***40 | Panel-Box | 1 |
| 9Y***41 | Panel As-Box | 1 |
252-7535 Panel Gp-Circuit Breaker -Cover
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 12 |
| 25***23 | Panel | 1 |
| 25***35 | Panel Group-Circuit Breaker; -Cover | 1 |
138-3809 Relay As -Power
| 13***09 | Relay As; (Heater Control)(24 Vdc Pump Energize) | 1 |
134-1157 Relay Gp -Engine Failure
| 12***26 | Relay Group; -Auxiliary | 1 |
| 13***57 | Relay Group; -Engine Failure | 1 |
| 15***81 | Relay Group; -Engine Failure | 1 |
158-6181 Relay Gp
| 15***81 | Relay Group; -Engine Failure | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
128-3326 Relay Gp -Auxiliary
| 12***26 | Relay Group; -Auxiliary | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
250-6621 Sender As-Temperature
| 25***21 | Sender As-Temperature | 1 |
105-2048 Sensor & Mtg Gp-Radiator
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***48 | Sensor & Mtg Group-Radiator | 1 |
| 11***52 | Harness As-Sensor; (Coolant Level) | 1 |
111-3794 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***94 | Sensor Group-Coolant Level; -Coolant Loss-Aftercooler, Jacket Water | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
143-8540 Sensor Gp-Coolant Level
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 14***40 | Sensor Group-Coolant Level | 1 |
| 14***61 | Harness As-Switch; (Coolant Level) | 1 |
165-6634 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***34 | Sensor Group-Coolant Level; (Water, Coolant)(Scac Expansion Tank) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
9w-5565 Sensor Gp-Temp & Press
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
| 7N***38 | Housing-Receptacle-Sure Seal-Assemble | 1 |
204-2518 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 20***18 | Sensor Group-Liquid Level; (Jacket Water) | 1 |
239-9957 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 23***57 | Sensor Group-Liquid Level; -Coolant Loss | 1 |
163-8516 Sensor Gp-Pressure
| 16***16 | Sensor Group-Pressure; -Boost And Engine Oil | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 1 |
| 19***27 | Harness As-Sensor; (14-Ga Wire)(Engine Oil Temperature) | 1 |
3e-1854 Sensor Gp-Pressure
| 3E***54 | Sensor Group-Pressure | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
228-9852 Sensor Gp-Pressure
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 1 |
| 22***52 | Sensor Group-Pressure | 1 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
7w-3355 Sensor Gp-Speed
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 4B***81 | Washer--Use With Customer'S Ground Bolt | 1 |
| 7W***55 | Sensor Group-Speed; -Engine Timing | 1 |
9x-5392 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
189-5746 Sensor Gp-Speed -Output
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***36 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 17***49 | Strap; (Marker) | 1 |
265-9034 Sensor Gp-Speed
| 11***66 | Seal-O-Ring | 1 |
| 13***07 | Washer; (21.1x28.1x0.9-mm Thk) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
8l-4171 Sensor Gp-Speed
| 8L***71 | Sensor Group-Speed; -Low Output | 1 |
102-9029 Sensor Gp-Speed
| 10***29 | Sensor Group-Speed; -Timing-Engine Speed | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 3 |
| 8L***86 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
3e-7886 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
6i-4909 Sensor Gp-Temperature -Generator Bearing
| 11***52 | Strip-Terminal | 1 |
| 11***21 | Lead As-Sensor | 1 |
| 11***73 | Sender As-Temperature; (10-Ohm)(Generator Bearing) | 2 |
6i-4907 Sensor Gp-Temperature -Generator Bearing
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
| 11***47 | Cover | 1 |
180-5420 Sensor Gp-Temperature
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 18***20 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
175-5341 Sensor Gp-Temperature
| 17***41 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
141-4161 Sensor Gp-Temperature -Generator Bearing
| 14***61 | Sensor Group-Temperature; -Generator Bearing | 1 |
141-4160 Sensor Gp-Temperature -Generator Bearing
| 14***60 | Sensor Group-Temperature; -Generator Bearing | 1 |
6i-4908 Sensor Gp-Temperature -Generator Bearing
| 11***52 | Strip-Terminal | 1 |
| 11***21 | Lead As-Sensor | 1 |
| 11***72 | Sender As-Temperature; (100-Ohm) | 2 |
6i-4906 Sensor Gp-Temperature -Generator Bearing
| 11***22 | Sender As-Temperature; (100-Ohm)(Generator Bearing) | 1 |
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
241-9591 Sensor Gp-Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 24***91 | Sensor Group-Temperature | 1 |
108-6424 Shutoff Gp-Electrical
| 10***24 | Shutoff Group-Electrical | 1 |
| 10***71 | Control Group-Engine Monitoring | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
8n-8486 Silencer Gp-Air Starting
| 1D***66 | Bolt Bracket Assembly To Yoke | 2 |
| 1D***69 | Bolt 107.95 mm(4.25 In.) Long; Bolt (Plate To Front Housing) | 2 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
112-6597 Silencer Gp-Air Starting
| 10***69 | Silencer-Air Starting | 1 |
| 11***97 | Silencer Group-Air Starting | 1 |
| 14***96 | Bolt-Socket Head; (1/2-13x1.25-In) | 2 |
6v-5582 Starting Motor Gp-Electric
| 3E***25 | Cover As; (Starting Motor) | 1 |
| 3E***27 | Kit-Bearing; (Starting Motor)(Incl Bearing Seals & Spacers) | 1 |
| 3E***28 | Kit; (Brush) (Includes O-Rings, Screw, Spring, & Brush) | 1 |
6v-4246 Starting Motor Gp-Electric
| 10***51 | Starting Motor Group-Electric; Motor Gp-Electric Hydraulic Pump | 1 |
| 6V***46 | Starting Motor Group-Electric | 1 |
| 6V***20 | Starting Motor Group-Electric | 1 |
106-8551 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***51 | Starting Motor Group-Electric; Motor Gp-Electric Hydraulic Pump | 1 |
207-1556 Starting Motor Gp-Electric
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 5 |
| 20***56 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
207-1562 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 20***62 | Starting Motor Group-Electric | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
6v-5539 Starting Motor Gp-Electric
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
| 6V***39 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 6V***82 | Starting Motor Group-Electric; (Nippondenso) | 1 |
237-1962 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 13 |
106-8554 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
6v-0927 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
7c-0527 Starting Motor Gp-Electric -Dual
| 20***62 | Starting Motor Group-Electric | 2 |
| 3L***04 | Shield-Terminal | 4 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
8n-3896 Starting Motor Gp-Electric -Dual
| 3L***36 | Spacer-Bracket To Diesel Water Passage Cover | 1 |
| 3L***04 | Shield-Terminal | 4 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
6v-4320 Starting Motor Gp-Electric
| 5C***74 | Nut (M5x.8 Thd); (M5x0.8-Thd) | 2 |
| 6V***20 | Starting Motor Group-Electric | 1 |
| 7X***62 | Washer-Hard; (13.5x19x0.8-mm Thk) | 5 |
121-2516 Strip As-Terminal
| 12***16 | Strip As-Terminal | 1 |
170-5397 Strip Gp-Terminal -Ac
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 5 |
170-5396 Strip Gp-Terminal -Rtd
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
| 31***98 | Block-Terminal; (600-Volt, 25-Ampere) | 34 |
170-5395 Strip Gp-Terminal -Thermocouple
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 7 |
126-6830 Strip Gp-Terminal
| 11***40 | Strip As; (Emcp Ii Ac) | 1 |
| 11***41 | Strip As; (Emcp Ii Dc) | 1 |
| 12***97 | Bracket As | 1 |
170-5399 Strip Gp-Terminal -Dc
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***06 | Bar | 1 |
| 17***99 | Strip Group-Terminal; -Dc | 1 |
170-5400 Strip Gp-Terminal -Main
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 15***55 | Fuse; (10-Ampere) | 2 |
| 17***00 | Strip Group-Terminal; -Main | 1 |
3n-7056 Support Gp-Battery
| 3N***54 | Support As-Battery | 1 |
| 3N***55 | Board | 1 |
| 3N***56 | Support Group-Battery | 1 |
143-7886 Switch As -Circuit Breaker Position, Fault Indicator
| 14***86 | Switch As; -Circuit Breaker Position, Fault Indicator | 1 |
105-7931 Switch As-Auxiliary
| 10***31 | Switch As-Auxiliary; -Circuit Breaker | 1 |
105-7932 Switch As-Auxiliary
| 10***32 | Switch As-Auxiliary | 1 |
158-4240 Switch As-Selector
| 15***40 | Switch As-Selector | 1 |
4w-4755 Switch Gp-Magnetic
| 3B***01 | Lockwasher (Part Of 3f***99 Switch) | 2 |
| 3F***56 | Lockwasher; (8.43x15.5x0.76mm Thk) | 2 |
| 4B***47 | Nut,Plain,Square Circuit Breaker Uoc:Bsv,Bsx | 2 |
175-2322 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***22 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
119-0800 Switch Gp-Magnetic
| 11***00 | Switch Group-Magnetic | 1 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 2 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 2 |
175-2324 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
3e-0075 Switch Gp-Magnetic
| 17***22 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 3E***75 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
6i-1230 Switch Gp-Magnetic
| 3E***75 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 3E***61 | Plug As-Connector; (2-Pin) | 1 |
| 3E***62 | Wedge-Plug Lock; (2-Pin) | 1 |
119-0801 Switch Gp-Magnetic
| 11***01 | Switch Group-Magnetic | 1 |
| 3B***01 | Lockwasher (Part Of 3f***99 Switch) | 2 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 2 |
134-8621 Switch Gp-Start
| 11***54 | Circuit Breaker As; (20-Ampere) | 1 |
| 11***00 | Switch Group-Magnetic | 1 |
| 11***01 | Switch Group-Magnetic | 1 |
3e-0264 Switch Gp-Temperature
| 3E***64 | Switch Group-Temperature; -Coolant | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
4p-2126 Switch Gp-Temperature
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 4P***26 | Switch Group-Temperature | 1 |
| 7E***91 | Switch As-Temperature; (Inlet Air) | 1 |
5n-9365 Thermocouple
| 5N***65 | Thermocouple | 1 |
244-4462 Transformer As -Current
| 24***62 | Transformer As; -Current | 1 |
243-3129 Transformer As
| 24***29 | Transformer As | 1 |
| 24***06 | Transformer | 2 |
| 7E***63 | Strip-Terminal | 1 |
7c-7542 Transformer As
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 4P***55 | Transformer | 1 |
| 4P***56 | Holder-Fuse | 1 |
244-4460 Transformer As -Current
| 24***60 | Transformer As; -Current | 1 |
130-8240 Transformer As
| 13***40 | Transformer As | 1 |
130-8239 Transformer As
| 13***39 | Transformer As | 1 |
243-3128 Transformer As
| 24***28 | Transformer As | 1 |
| 24***06 | Transformer | 2 |
| 4P***55 | Transformer | 1 |
204-3544 Transformer As-Current
| 20***44 | Transformer As-Current | 1 |
206-0247 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***21 | Transformer As-Current | 3 |
| 20***47 | Transformer Group-Current | 1 |
206-0244 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***90 | Transformer As-Current; (3000:5 Ratio)(3000:5) | 3 |
| 20***44 | Transformer Group-Current | 1 |
206-0251 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***78 | Transformer-Current; (Ratio 800:5) | 3 |
| 20***51 | Transformer Group-Current | 1 |
206-0242 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***88 | Transformer As-Current | 3 |
| 20***42 | Transformer Group-Current | 1 |
229-5838 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***86 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
206-0245 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***91 | Transformer As-Current | 3 |
| 20***45 | Transformer Group-Current | 1 |
206-0240 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***24 | Transformer As-Current | 3 |
| 20***40 | Transformer Group-Current | 1 |
206-0249 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***23 | Transformer As-Current | 3 |
| 20***49 | Transformer Group-Current | 1 |
206-0250 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***77 | Transformer As-Current | 3 |
| 20***50 | Transformer Group-Current | 1 |
206-0243 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***89 | Transformer As-Current | 3 |
| 20***43 | Transformer Group-Current | 1 |
206-0248 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***22 | Transformer As-Current | 3 |
| 20***48 | Transformer Group-Current | 1 |
229-5837 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***85 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
206-0246 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***15 | Transformer As-Current | 3 |
| 20***46 | Transformer Group-Current | 1 |
206-0253 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 13***59 | Transformer As-Current | 3 |
| 20***53 | Transformer Group-Current | 1 |
206-0241 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***87 | Transformer As-Current | 3 |
| 20***41 | Transformer Group-Current | 1 |
206-0252 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***95 | Transformer As-Current | 3 |
| 20***52 | Transformer Group-Current | 1 |
232-6346 Transformer Gp-Ignition
| 12***72 | Seal-O-Ring | 1 |
| 12***38 | Spring-Transformer | 1 |
| 13***51 | Seal; (Pressure Relief) | 1 |
175-7748 Transformer Gp-Potential
| 17***48 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 1 |
243-3204 Transformer Gp-Potential
| 24***28 | Transformer As | 1 |
| 24***04 | Transformer Group-Potential | 1 |
| 6V***89 | Nut-Full (5/16 X 18 Thd) | 4 |
243-3205 Transformer Gp-Potential
| 24***29 | Transformer As | 1 |
| 24***05 | Transformer Group-Potential | 1 |
| 6V***89 | Nut-Full (5/16 X 18 Thd) | 4 |
135-8211 Transformer Gp-Potential
| 12***46 | Resistor | 1 |
| 13***22 | Bracket-Transformer | 1 |
| 13***11 | Transformer Group-Potential | 1 |
178-7193 Transformer Gp-Potential
| 15***71 | Shelf; (Transformer) | 1 |
| 17***93 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 3 |
5n-8980 Valve As-Solenoid -Air Start
| 3F***65 | Locknut; (1/2-14-Nptf-Thd) | 1 |
| 5N***43 | Adapter (Small); (.50-14 Thd) | 1 |
| 5N***80 | Valve As; -Air Start | 1 |
1l-2073 Valve Gp-Pressure Reducing -Rh
| 0T***20 | Bolt (1.25 In. Long X .438 In. Dia.) | 1 |
| 1H***69 | Button-Spring | 1 |
| 1H***70 | Chamber | 1 |
4p-9596 Valve Gp-Solenoid -Gas Shutoff
| 13***22 | Harness As-Solenoid; (Fuel Shutoff) | 1 |
| 3B***00 | Elbow | 2 |
| 3B***96 | Fitting; (Nipple) | 4 |
9y-6992 Valve Gp-Solenoid -Gas Shutoff
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 4P***77 | Gasket | 1 |
| 9X***06 | Receptacle As | 1 |
9y-6061 Valve Gp-Solenoid -Gas Shutoff
| 3B***96 | Fitting; (Nipple) | 1 |
| 7X***51 | Elbow-Union | 1 |
| 9Y***61 | Valve Group-Solenoid; -Gas Shutoff | 1 |
103-0692 Valve Gp-Solenoid -Gas Shutoff
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 7X***78 | Coil As | 1 |
130-5177 Valve Gp-Solenoid -Air Start
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***31 | Valve Group-Solenoid; (Air Start) | 1 |
| 13***77 | Valve Group-Solenoid; -Air Start-Air Starting | 1 |
7c-0301 Harness As-Panel -Circuit Breaker
| 3P***54 | Grommet | 1 |
| 3S***88 | Dispenser Group-Marker Tape; (Numbers 0ne To One Thousand)(No 1 To 1000) | 1 |
| 5P***76 | Terminal-Fork; (14-Ga To 16-Ga, No. 10 Screw)(14-16 Gauge-No. 10 Screw) | 2 |
106-5670 Harness As-Panel -Circuit Breaker
| 10***70 | Wiring Group; -Circuit Breaker | 1 |
| 10***71 | Marker-Wire | 1 |
| 5N***61 | Conduit-Flexible; (12.7mm .50in Id) | 20 |
113-3380 Wiring Gp-Eis
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 15 |
| 11***80 | Wiring Group-Eis | 1 |
| 11***18 | Clip | 16 |
145-5138 Wiring Gp-Electronic Control
| 12***30 | Harness As-Power; -Digital Voltage Regulator | 1 |
| 14***38 | Wiring Group-Electronic Control | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 5 |
4p-9575 Wiring Gp-Engine
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 1 |
| 10***25 | Name-Plate (Lubrication), Mounting Group-Instrument Panel | 1 |
154-3851 Wiring Gp-Engine -Electric Start
| 14***63 | Plug As-Connecting | 1 |
| 15***51 | Wiring Group-Engine; -Electric Start | 1 |
| 15***52 | Harness As-Wiring; (Electric Start) | 1 |
241-3378 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 3 |
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
242-7961 Wiring Gp-Generator
| 24***04 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***61 | Wiring Group-Generator | 1 |
| 24***52 | Harness As-Power; -Digital Voltage Regulator | 1 |
243-4269 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 9 |
| 24***69 | Wiring Group-Generator | 1 |
| 24***01 | Harness As-Wiring; (Vr6 Voltage Regulator) | 1 |
241-3379 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 10 |
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 24***68 | Harness As-Wiring; (Voltage Adjustment) | 1 |
242-7960 Wiring Gp-Generator
| 24***00 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***60 | Wiring Group-Generator | 1 |
261-7168 Wiring Gp-Generator
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 4 |
| 26***67 | Harness As-Wiring; (Shunt Trip) | 1 |
243-4285 Wiring Gp-Generator
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 24***71 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***85 | Wiring Group-Generator | 1 |
122-0320 Wiring Gp-Generator -Shunt Trip
| 12***20 | Wiring Group-Generator; -Shunt Trip | 1 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
| 7K***81 | Strap-Pressure & Return Hoses To | 10 |
107-7541 Wiring Gp-Instr & Ignition
| 10***41 | Wiring Group-Instr & Ignition | 1 |
| 10***42 | Harness As-Wiring; -Eis | 1 |
| 1L***61 | Plug (Use Without Ammeter); (Mtd. On Instr. Panel) | 1 |
192-4134 Wiring Gp-Pyrometer
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 15***77 | Washer; (4.445x9.525x1.092-mm Thk) | 4 |
| 17***41 | Sensor Group-Temperature | 16 |
176-5866 Wiring Gp-Sensor
| 13***58 | Cable-Electrical; (16-Ga)(3089-cm) | 0 |
| 17***66 | Wiring Group-Sensor | 1 |
| 17***69 | Harness As-Sensor | 1 |
Enclosures, Guards And Bases
324-2403 Bracket Gp-Support
| 16***76 | Brace | 2 |
| 18***13 | Plate | 1 |
| 32***03 | Bracket Group-Support | 1 |
324-4576 Bracket Gp-Support
| 18***12 | Brace-Engine Support | 2 |
| 18***13 | Plate | 1 |
| 32***76 | Bracket Group-Support | 1 |
4p-9064 Guard Gp-Extension
| 1V***23 | Plate | 4 |
| 2N***85 | Nut-Clip-Damper Guard To Coupling Guard | 8 |
| 4P***63 | Guard As-Extension | 1 |
3n-5764 Guard Gp-Extension
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 1V***23 | Plate | 8 |
| 2N***85 | Nut-Clip-Damper Guard To Coupling Guard | 16 |
160-9800 Pad-Isolator
| 16***00 | Pad-Isolator | 1 |
122-4869 Panel As-Enclosure -Extension Box
| 12***69 | Panel As-Enclosure; -Extension Box | 1 |
153-1030 Rail Gp-Engine & Gen Support
| 15***30 | Rail Group-Engine & Gen Support | 1 |
| 18***10 | Brace-Engine Support | 1 |
| 18***21 | Support As; (Lh) | 1 |
153-1031 Rail Gp-Engine & Gen Support
| 15***31 | Rail Group-Engine & Gen Support | 1 |
| 18***10 | Brace-Engine Support | 1 |
| 18***23 | Support As; (Rh) | 1 |
150-2536 Rail Gp-Engine & Gen Support
| 15***36 | Rail Group-Engine & Gen Support | 1 |
| 15***51 | Support As; (Rh) | 1 |
| 15***52 | Support As; (Lh) | 1 |
245-8735 Rail Gp-Engine & Gen Support
| 23***06 | Rail As | 1 |
| 24***35 | Rail Group-Engine & Gen Support | 1 |
| 7X***70 | Bolt-Plt; (3/4unc X 3 1/2) | 36 |
167-0503 Rail Gp-Engine Support
| 16***01 | Support-Engine & Radiator; (Rh) | 1 |
| 16***03 | Rail Group-Engine Support | 1 |
| 33***16 | Support-Engine & Radiator; (Lh) | 1 |
200-2601 Rail Gp-Engine Support
| 18***11 | Brace-Engine Support | 1 |
| 20***01 | Rail Group-Engine Support | 1 |
| 20***41 | Support-Lh | 1 |
195-8094 Rail Gp-Engine Support
| 18***11 | Brace-Engine Support | 2 |
| 19***94 | Rail Group-Engine Support | 1 |
| 19***95 | Support-Rh | 1 |
9y-0851 Rail Gp-Engine Support
| 33***12 | Support-Engine; (Lh) | 1 |
| 8T***94 | Washer; (3/4 Hardened) (Current Adapters) | 28 |
| 8T***98 | Capscrew; (Hex Hd) (3/4-10x1 3/4 Gd 8 Z) (Early Adapters) | 28 |
7w-3759 Rail Gp-Engine Support
| 1A***58 | Bolt 1.75 In. (44.45 mm) Long | 44 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 44 |
| 7W***59 | Rail Group-Engine Support | 1 |
7n-8384 Rail Gp-Engine Support
| 1A***58 | Bolt 1.75 In. (44.45 mm) Long | 40 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 40 |
| 7N***84 | Rail Group-Engine Support | 1 |
Engine Arrangement
199-2601 Engine Ar
| 11***74 | Gear Group-Rear; -Cam Drive | 1 |
| 11***59 | Cylinder Block Group | 1 |
| 12***81 | Gear Group-Front; -Low Speed, Standard Rotation | 1 |
199-2600 Engine Ar
| 11***74 | Gear Group-Rear; -Cam Drive | 1 |
| 11***59 | Cylinder Block Group | 1 |
| 11***50 | Lines Group-Turbocharger Vent | 1 |
199-2637 General Ar
| 19***01 | Engine Ar | 1 |
| 19***37 | General Ar | 1 |
199-2878 General Ar
| 19***00 | Engine Ar | 1 |
| 19***78 | General Ar | 1 |
8n-7151 Installation Ar
| 1A***22 | Bolt-Generator To Flywheel Housing | 16 |
| 1B***33 | Nut--Generator To Support Assembly | 4 |
| 1D***37 | Bolt-Generator To Support Assembly | 6 |
Fuel System
118-7590 Actuator As
| 11***90 | Actuator As | 1 |
1w-8887 Actuator Gp-Governor
| 14***43 | Governor Group | 1 |
| 1W***35 | Drive Group-Governor; Governor Drive Group | 1 |
| 1W***87 | Actuator Group-Governor | 1 |
178-4529 Actuator Gp-Governor
| 10***55 | Conduit As | 1 |
| 11***90 | Actuator As | 1 |
| 17***29 | Actuator Group-Governor | 1 |
178-4530 Actuator Gp-Governor
| 17***29 | Actuator Group-Governor | 1 |
| 17***30 | Actuator Group-Governor | 1 |
| 4P***51 | Control Group-Carburetor | 1 |
241-6966 Carburetor As
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 12***19 | Valve-Gas; (Carburetor) | 2 |
| 24***26 | Throttle As | 1 |
9y-3007 Carburetor Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 6 |
| 4B***88 | Bolt (5/16 X 28.58 mm); (5/16-18x1.125-In) | 1 |
| 4W***65 | Gasket | 1 |
6i-0773 Carburetor Gp
| 09***24 | Screw As; (12-24x0.625-In) | 12 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 20 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 12 |
6i-2343 Carburetor Gp
| 06***40 | Seal-O-Ring (Id=37.69mm) | 1 |
| 09***24 | Screw As; (12-24x0.625-In) | 6 |
| 10***39 | Body As; (Low Pressure) | 1 |
9y-4352 Carburetor Gp
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 6 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 6 |
| 5P***80 | Seal-O-Ring | 2 |
131-5457 Control As-Governor -Speed Control
| 13***57 | Control As-Governor; -Speed Control | 1 |
131-5452 Control As-Governor -Speed Control
| 13***52 | Control As-Governor; -Speed Control | 1 |
131-5451 Control As-Governor -Speed Control
| 13***51 | Control As-Governor; -Speed Control | 1 |
4p-5251 Control Gp-Carburetor
| 11***69 | Sleeve | 3 |
| 11***92 | Rod | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 7 |
4p-6942 Control Gp-Carburetor
| 11***69 | Sleeve | 6 |
| 12***80 | Rod | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 8 |
1w-2135 Drive Gp-Governor
| 06***57 | Seal-O-Ring | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 5 |
9y-5896 Drive Gp-Governor
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 2 |
| 1A***60 | Capscrew, Hex Head (1/2 - 13 X 2 G5); (Hex Head) (1/2-13x2 Gd 8 Z) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
4w-5267 Drive Gp-Tachometer
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 8 |
4p-4717 Filter Gp-Fuel
| 4P***17 | Filter Group-Fuel | 1 |
| 4P***20 | Filter Element-Fuel; (Gas) | 1 |
143-6143 Governor Gp
| 14***43 | Governor Group | 1 |
| 17***86 | Breather; (Governor) | 1 |
| 1W***80 | Gasket | 1 |
107-4471 Governor Gp-Electric
| 10***71 | Governor Group-Electric | 1 |
| 11***90 | Actuator As | 1 |
| 4B***81 | Washer--Use With Customer'S Ground Bolt | 1 |
2w-7978 Regulator As-Gas Pressure
| 1H***20 | Seal-O-Ring; (59.92mm Id) | 1 |
| 2B***08 | Plug-- Hydraulic Pump Mounting Cage | 1 |
| 2W***78 | Regulator As-Gas Pressure | 1 |
7c-9083 Regulator Gp-Gas Pressure
| 00***40 | Connector; (37 Degree) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 4 |
4p-9090 Regulator Gp-Gas Pressure
| 05***41 | Elbow | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 10***27 | Regulator Group-Gas Pressure | 2 |
100-8227 Regulator Gp-Gas Pressure
| 10***27 | Regulator Group-Gas Pressure | 1 |
| 13***84 | Body-Valve; (Gas Pressure Regulator) | 1 |
| 13***86 | Seal-O-Ring | 2 |
233-7973 Separator Gp-Water -Primary Fuel Filter
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 23***73 | Separator Group-Water; -Primary Fuel Filter | 1 |
4p-7380 Separator Gp-Water
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 4 |
240-8926 Throttle As
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 4 |
| 23***16 | Kit-Governor Shaft | 0 |
| 24***26 | Throttle As | 1 |
241-6968 Throttle As
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 4 |
| 23***16 | Kit-Governor Shaft | 1 |
| 24***79 | Kit-Repair; (Throttle) | 1 |
7e-9201 Throttle Gp
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 4 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 4 |
| 6L***96 | Screw-Pin; (10-32x0.75-In) | 2 |
7e-9202 Throttle Gp
| 24***68 | Throttle As | 1 |
| 4B***88 | Bolt (5/16 X 28.58 mm); (5/16-18x1.125-In) | 1 |
| 4W***65 | Gasket | 1 |
7e-1586 Throttle Gp
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 4 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 4 |
| 6L***96 | Screw-Pin; (10-32x0.75-In) | 2 |
7e-1598 Valve Gp-Fuel
| 12***29 | Plate | 1 |
| 12***30 | Piston | 1 |
| 1H***04 | Screw Assembly Adapter To Mounting Plate; Screw Assembly-Adapter To Mounting Plate | 6 |
133-7592 Valve Gp-Fuel
| 12***29 | Plate | 1 |
| 12***30 | Piston | 1 |
| 13***92 | Valve Group-Fuel | 1 |
Generators
9y-8400 Regulator Gp-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
7c-2663 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
149-6130 Regulator As-Voltage
| 14***30 | Regulator As-Automatic Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
7c-2664 Regulator Gp-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 6V***74 | Screw-Machine (6-32x0.25in); (6-32x0.25-In) | 16 |
202-0993 Adapter Gp-Generator Coupling
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0V***75 | Screw,Cap,Hexagon H Shaft Mtg,Accessory Drive | 6 |
6i-4883 Air Filter Gp-Generator
| 1P***86 | Bolt--Alternator Support To Circuit | 2 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
| 4B***38 | Screw-Machine; (10-32x15.88-mm) | 2 |
164-2473 Bracket & Mtg Gp-Generator
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 8 |
| 12***74 | Seal | 1 |
236-4504 Bracket Gp-Mounting
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 11***94 | Bracket As-Housing | 1 |
| 11***77 | Sleeve-Wear | 1 |
236-2490 Cable Gp-Generator Ground -Neutral
| 23***54 | Cable; (Grounding) | 1 |
| 23***90 | Cable Group-Generator Ground; -Neutral | 1 |
7c-2561 Connection Gp-Generator Leads
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 3 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 30 |
| 5S***82 | Capscrew; (Hex Hd) (1/2-13x1 3/8, Gd8, Z) | 12 |
106-7707 Connection Gp-Generator Leads
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 10***07 | Connection Group-Generator Leads | 1 |
| 10***11 | Bar-Neutral | 1 |
9y-0873 Connection Gp-Generator Leads
| 1D***17 | Nut-Plate And Angle Assembly To Hydraulic And Fuel Tanks; Nut Plate And Angle Assembly To Hydraulic And Fuel Tanks | 4 |
| 2A***39 | Bolt,Machine Tube To Torque Converter And Tube To Oil Cooler | 2 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 2 |
106-7715 Connection Gp-Generator Leads
| 10***15 | Connection Group-Generator Leads | 1 |
| 5S***82 | Capscrew; (Hex Hd) (1/2-13x1 3/8, Gd8, Z) | 9 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 28 |
122-0329 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 12 |
| 12***29 | Connection Group-Terminal Strip | 1 |
122-0331 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 18 |
| 12***31 | Connection Group-Terminal Strip | 1 |
147-7258 Connection Gp-Terminal Strip
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 2 |
| 12***13 | Panel As | 1 |
| 12***14 | Panel As | 1 |
126-7571 Connection Gp-Terminal Strip
| 12***30 | Strip Group-Terminal | 1 |
| 12***71 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 30 |
122-0330 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 15 |
| 12***30 | Connection Group-Terminal Strip | 1 |
9y-2582 Connection Gp-Terminal Strip
| 11***02 | Strip-Terminal, Plate | 3 |
| 11***03 | Strip-Terminal | 1 |
| 11***04 | Bracket | 1 |
122-0328 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 9 |
| 12***28 | Connection Group-Terminal Strip | 1 |
121-9480 Connection Gp-Terminal Strip
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 12***80 | Connection Group-Terminal Strip | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
9y-0903 Connection Gp-Terminal Strip
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
| 1D***17 | Nut-Plate And Angle Assembly To Hydraulic And Fuel Tanks; Nut Plate And Angle Assembly To Hydraulic And Fuel Tanks | 1 |
154-6193 Conversion Gp-Generator
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 11***17 | Ring; (Support) | 1 |
| 15***93 | Conversion Group-Generator | 1 |
5n-9421 Exciter & Heat Sink As
| 3N***45 | Screw-Forming; (5/16-18x1-In) | 4 |
| 4B***03 | Bolt (4 In. Long)--101.6 mm) | 3 |
| 4P***53 | Hub-Holder | 1 |
4p-8897 Air Filter Gp-Generator
| 1P***86 | Bolt--Alternator Support To Circuit | 2 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
| 4B***38 | Screw-Machine; (10-32x15.88-mm) | 2 |
9y-7181 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
128-7418 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 12***17 | Generator Group | 1 |
| 12***18 | Generator Ar | 1 |
7c-3069 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
7c-3073 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
7c-3074 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
7c-4914 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***09 | Regulator As-Voltage | 1 |
| 15***21 | Regulator As-Voltage | 1 |
7c-3072 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
4p-7271 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
4p-7273 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
6i-4850 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***09 | Regulator As-Voltage | 1 |
| 15***21 | Regulator As-Voltage | 1 |
121-3199 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 11***09 | Regulator As-Voltage | 1 |
| 12***98 | Generator Group | 1 |
128-7416 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 12***15 | Generator Group | 1 |
| 12***16 | Generator Ar | 1 |
126-8024 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 12***23 | Generator Group | 1 |
| 12***24 | Generator Ar | 1 |
6i-4854 Generator Ar
| 22***84 | Film-Identification; (Cat) | 2 |
| 22***24 | Film-Warning; (Automatic Engine Start) | 2 |
| 22***27 | Film-Warning; (Hot Surface) | 2 |
6i-4848 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
7c-3068 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
121-3201 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 12***00 | Generator Group | 1 |
| 12***01 | Generator Ar | 1 |
121-3200 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
9y-7180 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
7w-8677 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***43 | Screw; (1/4-20x0.625-In) | 10 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
4p-7270 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 05***71 | Mount | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 8 |
6i-4847 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
128-7417 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***64 | Nipple | 1 |
| 05***71 | Mount | 4 |
7c-4913 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***43 | Screw; (1/4-20x0.625-In) | 10 |
| 05***71 | Mount | 4 |
7w-8678 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 8 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
7w-8685 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
7w-8687 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
4p-7272 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 05***71 | Mount | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
6i-4853 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
7w-8686 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
128-7415 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***64 | Nipple | 1 |
| 05***71 | Mount | 4 |
121-3198 Generator Gp
| 05***71 | Mount | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
6i-4849 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 05***71 | Mount | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
130-4616 Heat Sink As
| 13***16 | Heat Sink As | 1 |
| 13***17 | Rectifier | 3 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
4p-6007 Heat Sink As
| 4P***07 | Heat Sink As | 1 |
| 4P***08 | Rectifier | 3 |
| 4P***09 | Varistor | 1 |
9y-7174 Heat Sink As-Negative
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***15 | Strip-Terminal; (Terminal) | 1 |
5n-5030 Heat Sink As-Negative
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***15 | Strip-Terminal; (Terminal) | 1 |
9y-7175 Heat Sink As-Positive
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***59 | Resistor Assem. | 1 |
5n-5027 Heat Sink As-Positive
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***59 | Resistor Assem. | 1 |
7w-8708 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 6 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 2 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
153-0191 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 6 |
| 15***91 | Installation Ar-Generator | 1 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 4 |
4w-8212 Insulator -Circuit Breaker Mount
| 4W***12 | Insulator; -Circuit Breaker Mount | 1 |
243-4270 Mounting Gp-Voltage Regulator
| 24***70 | Mounting Group-Voltage Regulator | 1 |
| 4L***25 | Lockwasher | 4 |
| 7X***01 | Bolt-Plt; (1/4unc X 1 1/4) | 4 |
242-3487 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 24***87 | Mounting Group-Voltage Regulator | 1 |
| 24***64 | Spacer; (8.5x12.7x94.3-mm Thk) | 3 |
124-1563 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
5n-9093 Regulator As-Voltage
| 4W***79 | Guide-Card | 4 |
| 4W***33 | Board As; (M3) | 1 |
| 5N***19 | Board Assem.; (M2) | 1 |
5n-5103 Regulator As-Voltage
| 1N***67 | Circuit Breaker As; (7.5 Amp) | 1 |
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***86 | Transformer As | 2 |
5n-5081 Regulator As-Voltage
| 4W***79 | Guide-Card | 4 |
| 5N***19 | Board Assem.; (M2) | 1 |
| 5N***81 | Regulator As; (Voltage-Perm. Magnet) | 1 |
7c-4903 Regulator As-Voltage
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***87 | Transformer As. | 2 |
| 4W***40 | Protector (Thermal) | 1 |
5n-9439 Regulator As-Voltage
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***87 | Transformer As. | 1 |
| 4W***40 | Protector (Thermal) | 1 |
5n-5100 Regulator As-Voltage
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***86 | Transformer As | 1 |
| 4W***40 | Protector (Thermal) | 1 |
5n-9440 Regulator As-Voltage
| 1N***67 | Circuit Breaker As; (7.5 Amp) | 1 |
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***87 | Transformer As. | 2 |
309-1019 Regulator As-Voltage
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
105-4401 Regulator As-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
7e-8261 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
114-5509 Regulator As-Voltage
| 11***09 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
114-5510 Regulator As-Voltage
| 11***10 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3835 Regulator As-Voltage -Digital
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
155-3820 Regulator As-Voltage
| 15***20 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
114-5511 Regulator As-Voltage
| 11***11 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3821 Regulator As-Voltage
| 15***21 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3832 Regulator As-Voltage -Digital
| 15***32 | Regulator As-Voltage; -Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
7e-8262 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
235-5725 Regulator As-Voltage -Digital
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 23***25 | Regulator As-Voltage; -Digital-Generator | 1 |
314-7755 Regulator As-Voltage -Digital
| 24***58 | Film-Warning; (Shock, Electrocution Hazard)(Shock, Electrocution Hazard) | 1 |
| 31***55 | Regulator As-Voltage; -Generator | 1 |
202-8634 Regulator As-Voltage -Digital
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
7c-2662 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
155-3819 Regulator As-Voltage
| 15***19 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
116-7849 Regulator Gp-Voltage -Digital
| 11***49 | Regulator Group-Voltage; -Digital | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
116-7847 Regulator Gp-Voltage
| 11***47 | Regulator Group-Voltage | 1 |
| 15***33 | Regulator As; (Voltage) | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
108-1870 Regulator Gp-Voltage
| 10***70 | Regulator Group-Voltage | 1 |
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
121-6202 Regulator Gp-Voltage -Digital
| 12***02 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
116-7850 Regulator Gp-Voltage
| 11***50 | Regulator Group-Voltage | 1 |
| 15***36 | Regulator As; (Voltage) | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
242-9702 Regulator Gp-Voltage
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
| 24***02 | Regulator Group-Voltage | 1 |
| 24***04 | Transformer Group-Potential | 1 |
155-3824 Regulator Gp-Voltage
| 15***24 | Regulator Group-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
116-7845 Regulator Gp-Voltage
| 11***45 | Regulator Group-Voltage | 1 |
| 12***87 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***31 | Regulator As-Voltage; (Digital) | 1 |
116-7848 Regulator Gp-Voltage
| 11***48 | Regulator Group-Voltage | 1 |
| 15***34 | Regulator Group-Voltage | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
242-9703 Regulator Gp-Voltage -Digital
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
| 24***03 | Regulator Group-Voltage; -Digital | 1 |
| 24***05 | Transformer Group-Potential | 1 |
116-7846 Regulator Gp-Voltage -Digital
| 11***46 | Regulator Group-Voltage; -Digital | 1 |
| 12***87 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
108-1869 Regulator Gp-Voltage
| 10***69 | Regulator Group-Voltage | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 21***81 | Regulator As-Voltage | 1 |
108-1872 Regulator Gp-Voltage
| 10***72 | Regulator Group-Voltage | 1 |
| 15***24 | Regulator Group-Voltage | 1 |
| 7E***74 | Film-Instruction; (Voltage Control Adjustment) | 1 |
7c-2711 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
| 2N***81 | Fan As; (8-Blade) | 1 |
4p-9018 Rotor As
| 10***61 | Ball Bearing | 1 |
| 2L***44 | Bearing-Roller | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
7c-2709 Rotor Gp-Generator
| 10***60 | Ball Bearing | 1 |
| 1N***10 | Ring-Retaining | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
9y-2901 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
| 2N***81 | Fan As; (8-Blade) | 1 |
6i-4875 Rotor As
| 10***61 | Ball Bearing | 1 |
| 1N***10 | Ring-Retaining | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
7c-2712 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
| 2N***81 | Fan As; (8-Blade) | 1 |
7c-5070 Rotor Gp-Generator
| 1F***11 | Bolt 3.50 In. (8.89 cm) Long | 12 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
| 2N***81 | Fan As; (8-Blade) | 1 |
4p-8795 Rotor As
| 10***61 | Ball Bearing | 1 |
| 2L***44 | Bearing-Roller | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
117-9581 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 11***67 | Cap-Bearing; (Drive End) | 1 |
| 11***81 | Rotor Group-Generator | 1 |
137-5512 Rotor Gp-Generator
| 11***66 | Cap-Bearing | 1 |
| 11***67 | Cap-Bearing; (Drive End) | 1 |
| 13***12 | Rotor Group-Generator | 1 |
117-9580 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 11***67 | Cap-Bearing; (Drive End) | 1 |
| 11***80 | Rotor Group-Generator | 1 |
136-1736 Rotor Gp-Generator
| 11***66 | Cap-Bearing | 1 |
| 11***67 | Cap-Bearing; (Drive End) | 1 |
| 13***36 | Rotor Group-Generator | 1 |
236-5552 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 15***32 | Ball Bearing | 1 |
| 23***52 | Rotor Group-Generator | 1 |
108-1194 Rotor Gp-Generator
| 10***94 | Rotor Group-Generator | 1 |
| 10***61 | Ball Bearing | 1 |
| 10***39 | Cap-Bearing | 1 |
236-5551 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 15***32 | Ball Bearing | 1 |
| 23***51 | Rotor Group-Generator | 1 |
110-4171 Heat Sink As
| 11***71 | Sink As-Heat | 1 |
| 11***22 | Rectifier; (Positive) | 1 |
| 11***24 | Rectifier; (Negative) | 1 |
137-5516 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 19 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 10***34 | Cover-Stator | 1 |
136-1995 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 22 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 10***34 | Cover-Stator | 1 |
4p-9019 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 19 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 10***34 | Cover-Stator | 1 |
4p-8794 Stator Gp-Main
| 03***43 | Screw; (1/4-20x0.625-In) | 22 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 10***34 | Cover-Stator | 1 |
Lubrication System
4p-8312 Breather Gp -Crankcase
| 03***31 | Seal-O-Ring | 1 |
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 4P***12 | Breather Group; -Crankcase | 1 |
7n-1875 Filler Gp-Engine Oil -Cylinder Block
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 2W***52 | Gasket | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
7e-9284 Filter Gp-Engine Oil -Bypass
| 00***12 | Connector-Flared | 2 |
| 00***25 | Elbow-Flared | 1 |
| 03***70 | Adapter-Pipe | 1 |
4w-6874 Filter Gp-Engine Oil -Rh
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
134-0975 Filter Gp-Engine Oil -Duplex
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
130-8164 Gauge Gp-Oil Filter Press Diff
| 11***90 | Hose As | 2 |
| 13***64 | Gauge Group-Oil Filter Press Diff | 1 |
| 13***65 | Lines Group-Instrument Panel; -Rh | 1 |
7c-6366 Gauge Gp-Oil Level (Dipstick)
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 4P***84 | Gauge As-Oil Level (Dipstick) | 1 |
7c-9784 Gauge Gp-Oil Level (Dipstick) -Deep Sump
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
3n-4869 Hose As
| 3N***69 | Hose As | 1 |
3n-4513 Hose As
| 3N***13 | Hose As | 1 |
235-1780 Hose As
| 23***80 | Hose As | 1 |
| 3N***10 | Hose As | 1 |
8n-0856 Hose As
| 8N***56 | Hose As | 1 |
235-4431 Hose As
| 23***31 | Hose As | 1 |
| 3N***68 | Hose As | 1 |
235-4434 Hose As
| 23***34 | Hose As | 1 |
| 3N***69 | Hose As | 1 |
114-4358 Lines Gp-Engine Oil
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
134-3749 Lines Gp-Engine Oil
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
7e-9285 Lines Gp-Engine Oil Filter
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 3R***59 | Flange,Pipe Hose To Oil Filter | 1 |
1w-3941 Lines Gp-Oil Supply -Prelubrication
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 7 |
5n-6241 Lines Gp-Prelubrication -Rh
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 13***45 | Clip-Loop | 3 |
4w-5770 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
4p-5638 Pump Gp-Engine Oil -2-Section Gear
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 9 |
| 11***49 | Gasket | 1 |
8n-6152 Pump Gp-Engine Oil -2-Section Gear
| 29***87 | Seal-O-Ring | 1 |
| 4P***38 | Pump Group-Engine Oil; -2-Section Gear | 1 |
| 4S***82 | Bolt 7.25 In. (18.42 cm) Long | 3 |
1w-4776 Pump Gp-Prelubrication
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 9 |
| 1H***59 | Seal-Lip Type | 2 |
4p-4926 Pump & Lines Gp-Prelubrication -Deep Sump
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
4p-4925 Pump & Lines Gp-Prelubrication -Shallow Sump
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 3 |
1w-4674 Pump Gp-Prelubrication
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 1M***81 | Spacer; (0.438x0.75x1-In Thk) | 4 |
| 1W***74 | Pump Group-Prelube | 1 |
3t-3735 Pump Gp-Prelubrication
| 00***94 | Key | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 9 |
113-4174 Pump Gp-Prelubrication
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
113-6996 Pump Gp-Prelubrication
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
2n-7613 Pump Gp-Prelubrication
| 2N***13 | Pump Group-Prelubrication | 1 |
| 7N***09 | Capacitor | 1 |
| 7N***10 | Motor Assem. | 1 |
229-8349 Pump Gp-Sump
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 4 |
5n-6237 Pump Gp-Sump
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 2 |
| 3N***97 | Pin-Tapered | 2 |
| 3N***99 | Gasket Set; (Includes 4 Gaskets) | 1 |
5n-4659 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
138-1968 Regulator Gp-Oil Level
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
216-8347 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
7w-7319 Regulator Gp-Oil Level
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
7w-3816 Valve Gp-Fluid Control -Duplex Oil
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 2W***13 | Cover Assem. | 1 |
| 2W***10 | Valve As-Oil; (Duplex) | 1 |
147-3738 Valve Gp-Fluid Sampling -Oil
| 14***38 | Valve Group-Fluid Sampling; -Engine Oil | 1 |
| 7X***87 | Valve As-Fluid Sampling; (Oil Cooler) | 1 |
| 8C***45 | Cap-Dust; (Engine Oil Quick Disconnect) | 1 |
Operator Station
123-6323 Box Gp-Control Panel
| 12***97 | Mounting Group-Instrument Panel | 1 |
| 12***23 | Box Group-Control Panel | 1 |
| 19***69 | Box Group-Control Panel | 1 |
195-4769 Box Gp-Control Panel
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 2 |
| 11***70 | Bushing; (Capped) | 2 |
| 12***16 | Mount-Flexible | 4 |
194-2461 Box Gp-Control Panel
| 12***72 | Seal; (135-cm) | 0 |
| 15***15 | Latch As | 2 |
| 15***23 | Hinge As | 2 |
4p-9571 Box Gp-Control Panel
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***01 | Kit-Marker | 1 |
| 10***02 | Terminal; (Single) | 50 |
130-3349 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
9y-2906 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 7C***30 | Film-Identification | 1 |
| 8C***46 | Strap-Jumper | 1 |
9y-2907 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 9Y***47 | Film-Identification; (Control Panel) | 1 |
| 9Y***07 | Control Group-Alarm Module | 1 |
7e-1234 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 7E***34 | Control Group-Alarm Module | 1 |
| 9Y***76 | Film; (Annunciator)(Control Panel) | 1 |
101-0225 Control Gp-Emcp Electronic
| 10***22 | Housing As; (Transformer Box-Emcp Ii) | 1 |
| 10***25 | Control Group-Emcp Electronic | 1 |
| 10***03 | Channel As; (Transformer-Emcp Ii) | 1 |
151-6261 Control Gp-Emcp Electronic
| 15***60 | Control Group-Emcp Electronic | 1 |
| 15***61 | Control Group-Emcp Electronic | 1 |
| 4P***07 | Film-Emcp Ii; (Graphic/Text) | 1 |
118-0175 Control Gp-Emcp Electronic
| 10***27 | Screw-Pan Head; (10-24x0.25-In) | 8 |
| 11***75 | Control Group-Emcp Electronic | 1 |
| 15***65 | Kit-Connecting Plug; (8-Pin)(Electronic Control Channel) | 1 |
137-5525 Control Gp-Emcp Electronic
| 13***25 | Control Group-Emcp Electronic | 1 |
| 1S***74 | Seal-O-Ring (164.69mm Id) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
151-6260 Control Gp-Emcp Electronic
| 15***60 | Control Group-Emcp Electronic | 1 |
| 1S***74 | Seal-O-Ring (164.69mm Id) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
137-5526 Control Gp-Emcp Electronic
| 13***15 | Film-Control Panel; (Generator Set Control +)(Emcpii+) | 1 |
| 13***25 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
6v-6148 Control Gp-Engine Monitoring
| 3E***36 | Film-Identification; (Status) | 1 |
| 3E***48 | Control Group-Engine Monitoring | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
124-4564 Control Gp-Engine Monitoring
| 12***64 | Control Group-Engine Monitoring | 1 |
| 20***28 | Control Group-Engine Electronic | 1 |
3e-8542 Control Gp-Engine Monitoring
| 3E***42 | Control Group-Engine Monitoring | 1 |
125-3668 Control Gp-Engine Monitoring
| 12***64 | Control Group-Engine Monitoring | 1 |
| 12***68 | Control Group-Engine Monitoring | 1 |
6v-6149 Control Gp-Engine Monitoring -Spark Ignited
| 6V***48 | Control Group-Engine Monitoring | 1 |
| 6V***49 | Control Group-Engine Monitoring; -Spark Ignited | 1 |
| 8C***88 | Seal-Security | 1 |
3e-7848 Control Gp-Engine Monitoring
| 1S***91 | Screw-Machine; (6-32x.25in) | 16 |
| 2L***77 | Terminal; (14-Ga To 16-Ga, 1/4-In Screw)(14-16 Gage, 6.4mm Screw) | 4 |
| 3E***73 | Relay As | 7 |
108-7871 Control Gp-Engine Monitoring
| 10***81 | Film-Control Panel | 1 |
| 10***71 | Control Group-Engine Monitoring | 1 |
| 6V***48 | Control Group-Engine Monitoring | 1 |
107-9023 Gauge As-Pressure -Engine Oil
| 03***41 | Elbow; (7/16-20 Str Thd) | 1 |
| 03***61 | Elbow; (45 Degree) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
130-8169 Gauge As-Pressure -Engine Oil
| 03***41 | Elbow; (7/16-20 Str Thd) | 1 |
| 03***61 | Elbow; (45 Degree) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
107-9026 Gauge As-Pressure -Differential Oil
| 10***04 | Lines Group-Instrument Panel | 1 |
| 10***26 | Gauge As-Pressure; -Differential Oil | 1 |
| 11***91 | Hose As | 2 |
130-8170 Gauge As-Pressure -Auxiliary Water
| 03***61 | Elbow; (45 Degree) | 1 |
| 11***97 | Film-Gauge Identification; (Auxiliary Water Pressure) | 1 |
| 11***91 | Hose As | 1 |
108-3921 Gauge Gp-Air Inlet Temperature
| 10***21 | Gauge Group-Air Inlet Temperature | 1 |
| 2W***15 | Plate-Air Inlet Manifold; (Cooler Coolant) | 1 |
| 3E***36 | Gauge-Temperature; (Manifold Air Temperature) | 1 |
3n-9012 Ammeter Gp
| 3N***90 | Film-Gauge Identification; (Ammeter) | 1 |
| 3N***92 | Ammeter As; (60-Ampere) | 1 |
| 3N***12 | Gauge Group-Ammeter; (60-Ampere) | 1 |
107-9028 Gauge Gp-Coolant Pressure
| 10***28 | Gauge Group-Coolant Pressure | 1 |
| 11***97 | Film-Gauge Identification; (Auxiliary Water Pressure) | 1 |
| 11***91 | Hose As | 1 |
108-3854 Gauge Gp-Coolant Temperature
| 10***54 | Gauge Group-Coolant Temperature | 1 |
| 3E***37 | Gauge Group-Coolant Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
107-9024 Gauge Gp-Coolant Temperature
| 10***24 | Gauge Group-Coolant Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
107-9021 Gauge Gp-Manifold Air Temp
| 10***21 | Gauge Group-Manifold Air Temp | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 2W***15 | Plate-Air Inlet Manifold; (Cooler Coolant) | 1 |
107-9025 Gauge Gp-Manifold Pressure
| 03***61 | Elbow; (45 Degree) | 1 |
| 10***22 | Lines Group-Instrument Panel | 1 |
| 10***25 | Gauge Group-Manifold Pressure | 1 |
107-9029 Gauge Gp-Oil Temperature
| 10***29 | Gauge Group-Oil Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
130-8163 Gauge Gp-Vacuum
| 11***90 | Hose As | 1 |
| 13***63 | Gauge Group-Vacuum | 1 |
| 13***68 | Lines Group-Instrument Panel | 1 |
107-9030 Gauge Gp-Vacuum
| 03***61 | Elbow; (45 Degree) | 1 |
| 10***22 | Lines Group-Instrument Panel | 1 |
| 10***30 | Gauge Group-Vacuum | 1 |
130-8162 Gauge Gp-Water Pressure Diff
| 03***61 | Elbow; (45 Degree) | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 11***96 | Film-Gauge Identification; (Engine Coolant Pressure) | 1 |
6i-2118 Gauge Gp-Water Pressure Diff
| 3E***35 | Gauge As-Pressure; (Water) | 1 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
| 6I***18 | Gauge Group-Water Pressure Diff | 1 |
107-9032 Gauge Gp-Water Pressure Diff
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***32 | Gauge Group-Water Pressure Diff | 1 |
333-2392 Kit-Electronic Conversion -Generator Set Control +
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***25 | Control Group-Emcp Electronic | 1 |
| 33***92 | Kit-Electronic Conversion; -Generator Set Control + | 1 |
130-8168 Lines Gp-Instrument Panel
| 00***40 | Connector; (Flared) | 1 |
| 06***95 | Elbow (Between Fuel Lines) | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
231-0529 Lines Gp-Instrument Panel -Water Pressure Differential
| 00***40 | Connector; (Flared) | 2 |
| 11***96 | Film-Gauge Identification; (Engine Coolant Pressure) | 1 |
| 11***91 | Hose As | 2 |
104-5904 Lines Gp-Instrument Panel
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 1 |
| 10***04 | Lines Group-Instrument Panel | 1 |
130-8165 Lines Gp-Instrument Panel -Rh
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 1 |
| 13***65 | Lines Group-Instrument Panel; -Rh | 1 |
243-5031 Lines Gp-Instrument Panel -Water Pressure Differential
| 00***40 | Connector; (Flared) | 1 |
| 1B***13 | Bolt,Machine Governor And Decelerator Control | 2 |
| 24***30 | Tube As | 1 |
104-5722 Lines Gp-Instrument Panel
| 00***40 | Connector; (Flared) | 1 |
| 06***95 | Elbow (Between Fuel Lines) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
107-9020 Meter Gp-Service
| 10***20 | Meter Group-Service | 1 |
| 2W***60 | Plug As | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 6 |
118-7862 Meter Gp-Volt
| 10***57 | Voltmeter Group; (24-Volt)(Instrument Panel) | 1 |
| 11***62 | Meter Group-Volt | 1 |
| 11***63 | Bracket | 1 |
121-4717 Module Gp-Alarm
| 12***17 | Module Group-Alarm | 1 |
| 9Y***06 | Control Group-Alarm Module | 1 |
121-4707 Module Gp-Alarm
| 12***07 | Module Group-Alarm | 1 |
| 7E***34 | Control Group-Alarm Module | 1 |
121-4716 Module Gp-Alarm
| 12***16 | Module Group-Alarm | 1 |
| 9Y***07 | Control Group-Alarm Module | 1 |
9x-0203 Module Gp-Relay Driver
| 2D***63 | Bolt; (1/4-28x1.75-In) | 2 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 2 |
| 9X***03 | Module Group-Relay Driver | 1 |
121-4710 Module Gp-Synchronizing Lights
| 10***71 | Module Group-Synchronizing Lights | 1 |
| 12***10 | Module Group-Synchronizing Lights | 1 |
| 12***88 | Harness As-Panel; -Reverse Power Relay | 1 |
106-5171 Module Gp-Synchronizing Lights
| 10***64 | Cover; (Synchronizing Lights Module) | 1 |
| 10***71 | Module Group-Synchronizing Lights | 1 |
| 17***81 | Nut; (1/4-20-Thd) | 2 |
162-8734 Module Gp-System Communication
| 10***85 | Battery; (Lithium)(Internal Backup) | 1 |
| 10***37 | Film-Display; (Communication Module) | 1 |
| 10***38 | Film-Interface; (Communication Module)(Rear) | 1 |
7w-0919 Mounting Gp-Control Panel
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
| 3K***60 | Nut, Hex (3/8 - 16 Nc, Plastic Insert) | 2 |
104-4704 Mounting Gp-Control Panel -Emcp Ii
| 10***04 | Mounting Group-Control Panel; -Emcp Ii | 1 |
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
7e-7078 Mounting Gp-Instrument Panel
| 1H***38 | Lockwasher, External Tooth (1/4); W/O Freespool Qty Is 6 | 4 |
| 6V***85 | Nut-Full (1/4-20 Thd); (1/4-20-Thd)(Full) | 4 |
| 7C***75 | Seal-Bellows | 1 |
101-8925 Mounting Gp-Instrument Panel
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 6 |
120-5297 Mounting Gp-Instrument Panel
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 6 |
136-6924 Panel Gp-Control
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***25 | Control Group-Emcp Electronic | 1 |
103-6193 Panel Gp-Control
| 10***93 | Panel Group-Control | 1 |
| 10***66 | Film-Control Panel; (Eis) | 1 |
| 10***02 | Terminal; (Single) | 45 |
4p-9566 Panel Gp-Control
| 10***66 | Film-Control Panel; (Eis) | 1 |
| 10***02 | Terminal; (Single) | 45 |
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
121-4712 Panel Gp-Electronic
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 12***12 | Panel Group-Electronic | 1 |
| 12***26 | Relay Group; -Auxiliary | 1 |
7e-8270 Panel Gp-Instrument
| 11***65 | Film-Panel; (Instrument) | 1 |
| 2W***99 | Diode As | 1 |
| 3N***14 | Relay As; (24-Volt) | 1 |
6l-7004 Potentiometer
| 6L***04 | Potentiometer | 1 |
124-3676 Pyrometer Gp
| 12***76 | Pyrometer Group | 1 |
| 19***34 | Wiring Group-Pyrometer | 1 |
| 28***70 | Pyrometer Group; (Exhaust Temperature Scanner) | 1 |
3n-4416 Pyrometer Gp
| 3N***16 | Pyrometer Group | 1 |
107-9022 Pyrometer Gp
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***22 | Pyrometer Group | 1 |
| 11***70 | Bushing; (Capped) | 1 |
121-4705 Seal Gp-Enclosure
| 10***72 | Seal; (Control) | 1 |
| 12***05 | Seal Group-Enclosure | 1 |
| 5L***80 | Washer; (0.490x0.875x0.050-In Thk) | 3 |
107-9019 Tachometer Gp
| 10***19 | Tachometer Group | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 6 |
| 7E***59 | Tachometer Group-Electric; Tachometer Group-Electric | 1 |
7e-3159 Tachometer Gp-Electric
| 19***48 | Tachometer Group | 1 |
| 6V***77 | Nut (8-32 Thd) | 2 |
| 7E***59 | Tachometer Group-Electric; Tachometer Group-Electric | 1 |
105-1457 Voltmeter Gp
| 10***57 | Voltmeter Group; (24-Volt)(Instrument Panel) | 1 |
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 2 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 2 |
Prime Package
9y-5587 Accumulator Gp -Uncharged
| 9T***47 | Seal-Kit | 1 |
| 9Y***87 | Accumulator Group; -Uncharged | 1 |
Service Equipment And Supplies
4w-8145 Chart-Circuit Breaker
| 4W***45 | Chart-Circuit Breaker | 1 |
4w-8000 Chart-Control Panel
| 4W***00 | Chart-Control Panel | 1 |
7e-4300 Chart-Instrument Panel
| 7E***00 | Chart-Instrument Panel | 1 |
6l-4502 Chart-Plate & Film
| 10***59 | Film-Warning; (Electric Shock)(Shock Read Man.) | 2 |
| 15***14 | Plate-Information; (Gas Engine) | 1 |
| 1H***50 | Plate-Notice; On L.H. Front Side Cover & Rear R.H. Cover | 2 |
208-7825 Film Gp -Generator
| 20***67 | Film; (Cat) | 2 |
| 20***68 | Film-Caterpillar | 1 |
| 20***25 | Film Group; -Generator | 1 |
236-7516 Kit-Governor Shaft
| 23***16 | Kit-Governor Shaft | 1 |
4p-3317 Kit-Installation -Exciter
| 4P***17 | Kit-Installation; -Exciter | 1 |
351-1745 Kit-Maintenance
| 12***72 | Seal-O-Ring | 16 |
| 13***51 | Seal; (Pressure Relief) | 16 |
| 19***18 | Spark Plug; (Ignition) | 16 |
351-1749 Kit-Maintenance
| 13***58 | Seal-O-Ring | 16 |
| 14***16 | Belt-Serpentine; (Alternator) | 1 |
| 31***62 | Spring | 16 |
351-1740 Kit-Maintenance
| 1R***26 | Filter Element As-Engine Oil; (Standard Efficiency) | 3 |
| 35***40 | Kit-Maintenance | 1 |
| 6V***49 | Seal-O-Ring; (196.22mm Id) | 2 |
121-9272 Kit-Marine Generator Parts
| 12***72 | Kit-Marine Generator Parts | 1 |
4p-7283 Kit-Parts -Generator
| 10***61 | Ball Bearing | 1 |
| 11***11 | Regulator As-Voltage | 1 |
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
4p-7282 Kit-Parts -Generator
| 10***60 | Ball Bearing | 1 |
| 11***10 | Regulator As-Voltage | 1 |
| 15***20 | Regulator As-Voltage | 1 |
4p-7286 Kit-Parts -Generator
| 10***61 | Ball Bearing | 1 |
| 11***11 | Regulator As-Voltage | 1 |
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
7e-5035 Kit-Rfi Filter
| 7E***35 | Kit-Rfi Filter | 1 |
7e-5034 Kit-Rfi Filter
| 7E***34 | Kit-Rfi Filter | 1 |
| 9Y***68 | Kit-Rfi Filter | 1 |
7c-2696 Kit-Space Heater
| 3N***45 | Screw-Forming; (5/16-18x1-In) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
7w-8710 Kit-Space Heater
| 3N***45 | Screw-Forming; (5/16-18x1-In) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
7w-9986 Kit-Space Heater
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
7w-9967 Kit-Space Heater
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
140-2304 Programmer-Gov Elek Control
| 14***04 | Programmer-Gov Elek Control | 1 |
137-8533 Shim Pack
| 13***33 | Shim Pack; (Includes 13-Shims) | 1 |
| 13***34 | Shim; (0.025-mm Thk) | 1 |
| 13***35 | Shim; (0.0508-mm Thk) | 1 |
G3516 serial number reference
The PIN/serial plate on a G3516 is on the engine block (left front area near the flywheel housing) for a bare engine, or on the generator-set skid rail or control panel nameplate for a packaged genset. The plate shows the full Product Identification Number; read the first three characters as the serial prefix that identifies the specific build/configuration, and the digits that follow as the sequential unit number within that prefix run (for example, prefix plus 00123 reads as unit 123 of that run). On full 17-character PINs used on later product, this same prefix and sequence make up the last 8 characters of the PIN.
| Prefix | Identifies | Notes |
|---|---|---|
| 3RC | Gas engine - SITA (spark-ignited, turbocharged aftercooled) natural gas configuration | Seen on natural gas generator set builds from the mid-2000s, rated in the high-700 kW range on 60 Hz packages. |
| 4EK | Gas engine - SITA / SI TA turbocharged aftercooled natural gas configuration | Widest-documented G3516 prefix, spanning units built from the late 1990s into the late 2010s. Covers prime and continuous duty ratings from roughly 750 kW up past 1,800 kW depending on voltage and speed. |
| 8LD | Gas engine - natural gas, engine-only (non-packaged) | Documented on a standalone natural gas engine parts manual rather than a packaged generator set. No further configuration or year detail found. |
| E6Z | Generator set package | Covered by its own operation and maintenance manual and a matching parts catalog. No additional configuration or year detail found. |
| L6A | Generator set package | One of the best-documented G3516 prefixes: full parts catalog, electrical and schematic manual, and factory service-information coverage all exist under this prefix alone. |
| L6G | Generator set package | Has its own dedicated service manual. Reported in the same production window as L6E and L6F prefixed units (around 2012), though those two carry lower confidence individually - confirm with dealer. |
| WPW | Gas engine - natural gas | Covered by a dedicated operation and maintenance manual. At least one documented built unit carries a 2006 build date. |
| WPT | Gas engine - natural gas | Appears on multiple dealer-listed units noted as originally built under this prefix, i.e. the factory-original engine serial rather than a later replacement engine. |
| ZBA | Generator set, including TA (turbocharged aftercooled) configuration | Seen on later-build units (around 2018) rated near 1,000 kW; at least one unit under this prefix is tagged as the TA configuration. |
| L6J | Generator set package, prime rated | confirm with dealer - seen on one documented 2013-built prime-rated unit (1,030 kW, 400V). Not found on general serial-prefix reference charts, so treat as a single-source data point pending dealer confirmation. |
| L6E | Generator set package | confirm with dealer - appears only on general serial-prefix reference charts alongside L6F and L6G; no dedicated manual or unit listing independently found. |
| L6F | Generator set package | confirm with dealer - same caveat as L6E: reference-chart listing only, no independent manual or unit listing found. |
| WPS | Gas engine - natural gas | confirm with dealer - appears on general serial-prefix reference charts only; no dedicated manual or real unit listing found. |
| CPG | Generator set package | confirm with dealer - reference-chart listing only. |
| CSZ | Generator set package | confirm with dealer - reference-chart listing only. The same code also turns up elsewhere tied to the diesel-fueled 3516 generator set, so verify the fuel type/model suffix carefully before relying on it. |
| ZAZ | Generator set package | confirm with dealer - reference-chart listing only. |
| 8BZ | Gen set engine | confirm with dealer - reference-chart listing only. |
Frequently asked questions
What engine does the Caterpillar G3516 generator set use?
It uses Cat's own V-16, four-stroke natural gas engine from the 3500 series, offered in lean-burn and turbocharged rich-burn configurations, about 67-69 liters displacement from a 170 mm bore and 190 mm stroke, rated at 1200 rpm for 60 Hz or 1500 rpm for 50 Hz genset duty.
How much does the Caterpillar G3516 generator set weigh?
Weight varies by configuration: the bare engine runs around 9,200 kg (20,400 lb), while a complete packaged genset with generator end, cooling package, and control panel ranges from about 11,800 kg (26,000 lb) on a continuous-rated package up to roughly 18,300 kg (40,400 lb) on a standby-rated package. Confirm against the arrangement drawing for your specific cooling and enclosure setup.
What replaced the Caterpillar G3516 generator set?
Cat kept expanding the platform rather than dropping it outright. G3516B added ADEM digital engine management, and later G3516C and G3516E generations pushed output and emissions control further, with G3516H now covering the top of that gas-engine range; Cat's C175 platform serves as the newer high-density alternative above the 3500-series gas engines.
What G3516 owners discuss
What do techs report about detonation control on the G3516's ignition system?
The ADEM engine control fitted to this platform runs detonation-sensitive ignition timing that retards spark on a per-cylinder basis when knock is sensed, instead of pulling timing back across the whole engine. Operators like that this protects the engine through fuel-quality swings (methane number changes in the gas supply), but note it can mask a developing problem: persistent retard logged against one or two cylinders is treated by mechanics as an early warning of a fouled plug, a lean cylinder, or a local cooling issue, not just a number to clear. Because uncorrected detonation risks piston and ring damage, have your dealer verify a repeating per-cylinder retard trend with the diagnostic tool before returning the unit to full load.
How long do spark plugs and ignition components actually last in the field?
Reported life varies a lot by configuration and gas quality. Figures discussed for engines in this displacement class range from roughly 2,000-4,000 hours on higher-compression setups up to 3,000-5,000 hours on lower-compression or prechamber-style plugs, with load factor and fuel wobbe index/methane number doing most of the swinging between those numbers. Few operators run to a fixed calendar interval — the common practice is pulling plugs based on trend data (misfire counts, per-cylinder exhaust temperature deviation) and replacing early on any cylinder running hot or misfiring, since one weak cylinder left in service is a common path to knock damage on the rest of the bank.
What air/fuel ratio quirks come up between the different G3516 configurations?
This nameplate covers both rich-burn (naturally aspirated and turbocharged-aftercooled) and lean-burn versions, and the two behave differently when air/fuel ratio control drifts. Rich-burn units run closer to stoichiometric to work with an exhaust catalyst and tolerate small ratio drift reasonably well. Lean-burn versions run a narrower combustion window; a wandering air/fuel ratio valve or a fouled oxygen sensor on these tends to show up first as misfire and rough load acceptance from running too lean, and can trip an air/fuel ratio fault before a detonation event ever appears. Mechanics recommend confirming which configuration is fitted before troubleshooting a knock or misfire complaint against generic gas-engine advice, since the failure signature runs opposite between the two.
How does the cooling system behave under load, and what usually causes overheating complaints?
Jacket water is thermostatically controlled, staying inside the block until it reaches roughly 80-85°C (176-185°F) before the thermostat opens flow to the radiator or heat-exchanger loop; the aftercooler and oil cooling circuits normally run separate from jacket water off the same pump. Field reports trace most high-jacket-water-temperature alarms to, in rough order of frequency: low coolant or trapped air in the system, a radiator or heat exchanger fouled on the air or raw-water side, and a slipping belt or weakening jacket water pump — the thermostat itself is rarely the actual cause. Because many of these units sit in enclosures or indoor rooms, restricted enclosure airflow or hot-air recirculation is also flagged as a load-dependent overheating cause that only shows up once the unit is carrying real load, not at idle.
What control-panel and sensor faults come up most often?
Two patterns dominate the reports. One is an abnormal/incorrect-data fault on the engine start/run/stop control input, where the control module expects two complementary signals from the control switch and a wiring or switch fault that makes them agree (or disagree) incorrectly throws the code — exact fault numbering varies by which control panel generation is fitted. The other is a false low-oil-pressure shutdown traced to a corroded or poorly crimped connector at the oil pressure sensor rather than an actual pressure problem, confirmed by comparing the panel reading against a mechanical gauge. A basic panel reset (control switch to off/reset, remove battery power briefly, reapply, cycle to stop) clears a good share of nuisance faults; when it doesn't, the pattern points to the harness and connectors before the sensor or panel itself. Because a false shutdown during a genuine low-oil-pressure event is the more dangerous failure direction, have your dealer verify sensor and wiring integrity with the factory diagnostic tool rather than just clearing the fault and returning to service.
What generator-end (alternator) issues come up as these units rack up hours?
Apart from the engine, owners point to winding insulation breakdown from heat or oil/moisture contamination as the main long-term wear path — it shows up as a slow decline in insulation resistance before an outright short, not a sudden failure. Drive-end and non-drive-end bearing wear or noise is the other common item, usually traced to a grease interval that slipped. On brush-type excitation systems, dirty slip rings or worn brushes are a frequent cause of loss-of-excitation or no-voltage-buildup complaints and are generally treated as routine cleaning rather than a real fault. Reported good practice is a periodic insulation-resistance (megger) check on the windings and a listen/vibration check on the bearings, not just watching output voltage stay in range.
What should I check before buying a used G3516 genset?
Compare total hours against the roughly 30,000-hour major-overhaul benchmark commonly cited for this platform when properly maintained, but ask specifically whether that clock has already been reset by a prior top-end or in-frame overhaul rather than trusting the hour meter alone. Get maintenance records — oil analysis trend history and whether spark plug/valve intervals were actually followed on schedule — and ask for a recent load bank test report; a genset that sat on standby duty with light or no real load history is a real risk for wet-stacking and carbon buildup even with low hours showing. Confirm which configuration is fitted (rich-burn vs lean-burn) and which control system generation is installed, since spare parts, air/fuel tuning, and emissions compliance differ by variant. Finally check the generator end's insulation resistance and bearing condition separately from the engine — sellers often report only engine hours and skip generator-end condition entirely.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Serial-range & configuration variants
This page covers the Caterpillar G3516. Related factory variants of the same model family:
G3516G3516
Need a specific G3516 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.