Caterpillar G3508
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar G3508 is a stationary, spark-ignited natural gas engine from Cat's G3500 series, built on the same 34.5 L (2105 cu in) V-8 block as the diesel 3508 but converted to gas fuel and ignition. It runs turbocharged and aftercooled with ADEM A3 electronic control, detonation-sensitive ignition timing, and per-cylinder knock sensing. Gross output spans roughly 391-514 bkW (524-690 bhp) at 1200-1400 rpm depending on the emissions rating ordered, and Cat-packaged generator sets built on it are commonly seen from about 330 kW up to roughly 500 kW continuous at 1200 rpm/60 Hz or 1500 rpm/50 Hz, varying by voltage and frequency selected. Bare-engine net dry weight runs about 3,940-5,420 kg (8,690-11,950 lb) depending on rating and accessories; a complete packaged genset adds the generator end, radiator, and enclosure on top of that. It was offered both as a bare engine for mechanical-drive or gas-compression duty and as a complete Cat generator set on an open skid or in a sound-attenuated weatherproof enclosure, with rich-burn and lean-burn combustion options and several NOx ratings to fit different site rules. The plain G3508 followed Cat's earlier mechanically governed big-bore gas engines into the ADEM-controlled G3500 lineup and was later followed on the same architecture by the G3508B, alongside gas-compression-specific G3508 LE and G3508J variants.
The defining change on this platform is the move from mechanical governing to ADEM electronic control with individual-cylinder detonation sensing, which let Cat raise power while holding emissions down and gave technicians a fault-code trail instead of guesswork. The later G3508B carries that further with two-stage aftercooling and a revised combustion setup that cuts engine-out NOx enough to meet current stationary spark-ignited limits without the customer-supplied aftertreatment a plain G3508 usually needs. Because the G3508 shares its base iron with the diesel 3508 and the newer G3508B, rebuilt long blocks and shared hardware still circulate even though it isn't a current new-unit offering; buyers should always confirm the exact nameplate and serial before ordering parts, since ignition, fuel, and emissions hardware don't cross over cleanly between the diesel 3508, the G3508, and the G3508B. The engine remains common in existing gas-lift, wellhead compression, and prime or standby generator installations, so overhaul kits, ignition components, and rebuild parts for it stay in steady demand on the used and parts market even though it is no longer a current new-build option.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar G3508 specifications
Engine
| Model / family | G3508 — V-8, 4-stroke, spark-ignited natural gas engine, part of the Cat G3500 series (shares the 3508 iron with the diesel 3508, but uses a gas fuel/ignition system, not the diesel fuel system) |
| Bore x stroke | 170 mm x 190 mm (6.7 in x 7.5 in) |
| Displacement | 34.5 L (2105 cu in) |
| Cylinders | 8, V-configuration |
| Aspiration | Turbocharged, aftercooled |
| Governor / control system | Electronic digital engine management (ADEM A3) with detonation-sensitive variable ignition timing, integrated protection and diagnostics |
| Combustion type | Low-emission lean-burn |
| Gross power range | About 391-514 bkW (524-690 bhp) at 1200-1400 rpm, varying by emissions rating and site altitude/ambient conditions; one common low-NOx rating lists 500 bkW (670 bhp) at 1400 rpm |
| Emissions tier | Meets U.S. EPA spark-ignited stationary NSPS requirements for the rating's model year; the lowest published rating is about 2 g/bhp-hr NOx, not-to-exceed |
Weights
| Engine net dry weight | About 5,420 kg (11,950 lb) on the 500 bkW/1400 rpm rating; some lower-output ratings on the same base engine publish a lighter net dry weight near 3,940 kg (8,690 lb) — weight varies by rating and accessory/cooling package |
| Shipping weight (bare engine) | About 5,420 kg (11,950 lb) for the 500 bkW/1400 rpm configuration |
| Ground pressure | Not applicable — stationary industrial engine/generator-set package, not a tracked or wheeled machine |
Dimensions
| Transport length | About 2,440 mm (96.1 in) bare engine on the 500 bkW/1400 rpm rating; other published ratings list a footprint up to about 2,520 mm (99 in) — varies by configuration |
| Transport width | About 1,768 mm (69.6 in) bare engine on the 500 bkW/1400 rpm rating; other ratings list up to about 2,010 mm (79 in) |
| Transport height | About 1,921 mm (75.6 in) bare engine on the 500 bkW/1400 rpm rating; other ratings list up to about 2,130 mm (84 in) |
| Wheelbase / track gauge | Not applicable — stationary engine/generator set |
| Ground clearance | Not applicable — stationary engine/generator set |
Performance
| Continuous mechanical-drive power | About 391-514 bkW (524-690 bhp) at 1200-1400 rpm, depending on the emissions rating chosen and site altitude/ambient temperature |
| Reference full-load rating | 500 bkW (670 bhp) at 1400 rpm on the 2 g/bhp-hr NOx (not-to-exceed) rating |
| Generator-set package output | Continuous electrical packages built on this engine are reported near 334-360 ekW at 1200 rpm / 60 Hz / 480V, and near 500 ekW (625 kVA) at 1500 rpm / 50 Hz / 400V; other export packages list about 480 ekW (600 kVA) at 60 Hz / 400V — output depends on the generator end, voltage, and frequency selected |
| Altitude / speed derate | Full rated torque and speed available to about 610 m (2,000 ft) altitude at 38°C (100°F) ambient; roughly 25% speed turndown available above that altitude to hold rated torque |
| Travel speed / gradeability | Not applicable — stationary engine/generator set, not a mobile machine |
Service capacities (summary)
| Fuel supply | Pipeline/wellhead natural gas through a gas pressure regulator, not a stored fuel tank; required inlet gas pressure about 242-276 kPa (35-40 psig) |
| Hydraulic system | Not applicable — no hydraulic system on this stationary engine/generator set |
| Engine oil (lube system refill) | About 230.9 L (61 gal); factory-recommended oil-change interval about 1000 hours |
| Cooling system | Total system about 124.9 L (33 gal), made up of a jacket-water circuit near 113.6 L (30 gal) and a separate aftercooler circuit near 11.4 L (3 gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
G3508 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with oil filters) | 230.9 L (61 US gal) refill capacity including filter change, on the V-8, 34.5 L (2105 cu in) G3508 block. Standard oil change interval is 1000 hours; extend only in 250-hour steps backed by oil analysis. Some generator-set skids with an add-on oil cooler or deep sump can vary slightly from this figure. | Cat Natural Gas Engine Oil (NGEO), SAE 40 only — Cat does not recommend multigrade oils in gas engines. Order of preference: Cat NGEO EL350, then Cat NGEO EL250, then standard Cat NGEO. Sulfated ash must stay in the 0.40-0.60% range; oils formulated for gasoline or diesel engines are not acceptable. Viscosity-by-climate: SAE 30 covers cold start down to 0C (32F) up to a 40C (104F) max ambient; SAE 40 covers 5C (41F) cold start up to a 50C (122F) max ambient. Below 10C (50F) ambient an oil heater is recommended for reliable cold starts. |
| Cooling system - jacket water circuit | 113.6 L (30 US gal) jacket water, out of a 124.9 L (33 US gal) total cooling system volume for the single-stage-aftercooled G3508. | Preferred: Cat Natural Gas Engine Coolant (NGEC), factory-fill 50/50 glycol-water premix, 3-year service life under a monitored coolant-analysis program. Acceptable alternative: Cat Diesel Engine Antifreeze/Coolant (DEAC), or a commercial heavy-duty coolant meeting the ASTM D6210 or D4985 spec (2-year and 1-year service life respectively). Do not use standard Extended Life Coolant (ELC) - it is not formulated for gas engines. Dose with Cat Supplemental Coolant Additive at 3-6% in a glycol/water mix. On sour or high-sulfur gas, hold the jacket water outlet at a minimum of 110C (230F) and keep the temperature rise across the engine under 8.3C (15F) to limit acid condensation in the crankcase. |
| Aftercooler (SCAC) circuit | 11.4 L (3 US gal), included within the 124.9 L (33 US gal) total cooling system capacity above; kept separate from jacket water by its own thermostat and pump. | Same coolant as the jacket water circuit - Cat NGEC preferred, Cat DEAC or an ASTM D6210/D4985 commercial heavy-duty coolant as the alternative. |
| Fuel system | No stored fuel volume - this engine burns piped natural gas fed at roughly 48-345 kPa (7-50 psig) depending on the rating, not liquid fuel carried in an onboard tank. | Pipeline-quality dry natural gas with a methane number of at least 30 (verify with a methane number analysis before commissioning). Wellhead, digester, landfill, or other sour/bio-gas sources need a matched engine arrangement, gas treatment, and shorter oil-sampling intervals. Size the fuel gas filter to capture at least 99% of 1-micron particles; no brand-name fuel product applies since this is a gaseous-fuel engine. |
| Hydraulic system and tank | Not applicable. The G3508 is a stationary gaseous-fuel engine driving a generator; it has no vehicle-type hydraulic propulsion or implement circuit. | Not applicable. |
| Transmission / final drives / axles | Not applicable. The engine couples directly to the generator through its flywheel and SAE No. 00 flywheel housing; there is no transmission, final drive, or axle in this package. | Not applicable. |
| Grease (chassis and accessory-drive points) | Spec only - no refill volume is published for generator-set mounting, linkage, or accessory-drive grease points. | Cat Multipurpose Grease (NLGI 2, lithium complex) covers general, moderate-duty points in moderate temperatures. For heavier-loaded or higher-temperature joints, step up to Cat Advanced 3Moly (NLGI 2, 3% moly) or Cat Ultra 5Moly (available NLGI 0, 1, or 2, 5% moly); pick the NLGI grade for your climate - grade 0 pumps down to about -43C (-45F), grade 2 suits warmer, more moderate operating temperatures. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar G3508 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
| Every 8,000 h |
|
| Every 12,000 h |
|
Servicing the G3508 beyond the schedule
Predictive maintenance and fluid analysis
Track engine oil condition with a sample at every 250-hour interval and hold the standard 1000-hour oil change unless trend data supports stretching it. Pull a Level 1 coolant sample at 250 hours and a full Level 2 sample at 2000 hours, since jacket-water and aftercooler coolant both carry the heat load of a lean-burn gas engine. Watch the ADEM A3 event log for detonation and knock codes, and monitor oil consumption and blowby, both early warnings of wet-stacking or ignition drift before a top-end job is needed.
Corrective and common repairs
Most non-mechanical downtime on the G3508 traces to ignition and sensor faults, not the base engine. Expect knock/detonation sensor and harness failures on either cylinder bank, lost or degraded speed/timing pickup signals causing no-start or shutdown events, and ignition transformer opens on individual cylinders. Spark plugs and ignition components wear faster here than on an equivalent diesel and are routine replacement items, not exceptions. Voltage-regulation faults and control-panel alarms round out the common list; pull stored fault and event codes before chasing a mechanical cause.
Overhaul and rebuild points
Reported top-end overhaul windows on this platform fall in the roughly 9,000-16,000 hour range, with in-frame work further out and major overhaul beyond that, all shifting earlier or later with fuel quality, load factor, and detonation history. Before scoping an overhaul, check for wet-stacking signs (oily exhaust and turbo deposits) from light-load duty, review the knock-event log, and confirm cylinder pressure and blowby trends. Valve lash, valve stem wear, and spark plug and ignition condition at recent 1000-hour services are the best predictors of what a teardown will find.
Seasonal and environment servicing
Cold-site starts need attention: below 10C (50F) ambient, fit an oil heater and match viscosity grade (SAE 30 down to 0C cold-start, SAE 40 for warmer climates) to avoid a hard start on the gas admission system. Keep jacket-water and aftercooler coolant on the same natural-gas-rated antifreeze, since standard extended-life coolant isn't approved for this engine. On wellhead, digester, or associated gas sites, re-verify methane number and BTU content each season, since fuel composition swings force a power derate. Drain the aftercooler circuit more often in humid or high-load seasons.
G3508 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1D-4540 | Bolt,Machine Fuel Filter Mounting | Fuel system service | Check fitment → |
| 4P-4720 | Filter Element-Fuel | Fuel system service | Check fitment → |
| 134-6307 | Filter Element As-Fuel | Fuel system service | Check fitment → |
| 6V-3907 | Seal-O-Ring | Fuel system service | Check fitment → |
| 8N-2556 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
G3508 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| 100-01 | Engine oil pressure below the normal operating range | Low oil level, restricted or plugged oil filter, worn oil pump, or a faulty oil pressure sensor/wiring | Check oil level and filter condition first, confirm the sensor reading against a manual gauge, and shut the unit down if pressure is genuinely low |
| 110-00 | Jacket water (coolant) temperature above the normal operating range | Low coolant level, blocked radiator or heat exchanger, failed thermostat, or water pump fault | Check coolant level and flow, inspect the cooling circuit for blockage or fouling, and verify the sensor reading against a manual gauge |
| 190-08 | Engine speed/timing signal abnormal - erratic, lost, or out-of-range frequency from the speed sensor, which can trigger overspeed protection | Damaged speed/timing sensor, chafed wiring, loose connector, or incorrect sensor air gap | Inspect the speed/timing sensor and its wiring, check and reset the sensor gap, and reseat connectors before restarting |
| 168-01 | System/battery voltage below the normal operating range | Weak or discharged starting battery, charging system fault, or corroded/loose battery cable connections | Test battery condition and charging output, clean and tighten connections, and replace the battery or charging component if it fails test |
| 318-01 | Loss of or abnormally low signal from the right-bank detonation (knock) sensor, so the control can no longer monitor knock on that bank | Failed or disconnected detonation sensor, damaged sensor wiring, or a loose/corroded connector | Inspect the right-bank sensor connector and wiring, test sensor resistance, and replace the sensor if it fails test |
| 319-01 | Loss of or abnormally low signal from the left-bank detonation (knock) sensor, so the control can no longer monitor knock on that bank | Failed or disconnected detonation sensor, damaged sensor wiring, or a loose/corroded connector | Inspect the left-bank sensor connector and wiring, test sensor resistance, and replace the sensor if it fails test |
| 325 | Detonation (knock) detected on one or more cylinders; the ignition control is retarding timing to protect the engine, or has reached its retard limit | Off-spec fuel gas quality or composition, incorrect air-fuel ratio setting, high intake air temperature, or worn ignition components | Check fuel gas quality and the air-fuel ratio setting, inspect the ignition system, and review load and ambient conditions before returning to full load |
| 313-05 | Open circuit on a cylinder's ignition transformer primary circuit (one of a numbered series, one code per cylinder position) | Failed ignition transformer, broken or chafed primary wiring, or a loose connector at that cylinder | Identify the flagged cylinder position, inspect and test the ignition transformer and its primary wiring, and replace the transformer if it fails test |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
G3508 attachments & work tools
Ground-engaging work tools
Not applicable. This is a bare gas engine-generator power unit, not a mobile machine, so no buckets, blades, forks, rippers, or hydraulic quick-couplers exist for it. Any "attachments" for this model are packaging and control options rather than ground-engaging tools.
Cooling system configuration
Offered with an engine-driven, skid-mounted radiator as the standard cooling arrangement, or as a remote-radiator arrangement where the radiator ships separately for sites with ducting or space constraints. Jacket-water and lube-oil cooling are combined into one circuit on this engine family, and the choice between radiator styles is a site-layout decision, not a rating-driven one.
Enclosure and weather/noise protection
Available as an open, skid-mounted set for indoor or engine-room installs, or in a factory sound-attenuated, weatherproof enclosure for outdoor or noise-sensitive sites. Enclosed packages typically integrate the exhaust silencer and, on some builds, a fluid-containment base under the skid.
Control panel and monitoring
Standard factory control on this genset is a digital control panel handling metering, protection, and engine/generator monitoring over the Cat data link. Sets meant to run in parallel with other units or with utility power can be specified with a later switchgear-and-paralleling control platform instead of the base panel.
Exhaust and silencing
A critical-grade exhaust silencer option is offered for noise-sensitive sites, either mounted inside a sound-attenuated enclosure or supplied loose for remote stack routing on open-skid installs.
Generator end and output configuration
Paired with a brushless generator end sized to the ordered output; published continuous ratings for this set span roughly 330-500 kW depending on voltage, frequency (50 Hz or 60 Hz), and speed (1200 or 1500/1800 rpm) selected, so exact alternator frame size varies by the configuration ordered rather than being fixed.
All G3508 assemblies by section
Every catalogued assembly group for the Caterpillar G3508. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
9y-3187 Accumulator Gp-Turbocharger
| 06***56 | Seal-O-Ring | 2 |
| 06***04 | Spacer; (0.459x0.625x1.188-In Thk) | 4 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
7w-9828 Adapter Gp-Air Cleaner
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 48 |
| 5N***30 | Gasket | 2 |
| 7W***28 | Adapter Group-Air Cleaner | 1 |
7n-8549 Adapter Gp-Air Cleaner
| 1W***31 | Strip | 8 |
| 1W***32 | Strip | 4 |
| 1W***33 | Strip | 8 |
4p-5698 Aftercooler Gp-Raw Water
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 40 |
| 2D***34 | Bolt-Socket Head; (3/8-16x1-In) | 24 |
| 4P***31 | Bonnet | 1 |
4p-7448 Aftercooler Gp-Raw Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 20 |
| 4P***98 | Aftercooler Group-Raw Water | 1 |
| 4P***48 | Aftercooler Group-Raw Water | 1 |
4p-8882 Aftercooler Gp-Treated Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 72 |
| 15***05 | Gasket | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 16 |
9y-0673 Air Cleaner Gp -Industrial
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 12 |
214-6134 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
| 21***34 | Air Cleaner Group | 1 |
8n-3378 Air Cleaner Gp
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
| 2K***73 | Locknut Inside Guard Assembly | 4 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 2 |
5n-7822 Air Cleaner Gp
| 5N***22 | Air Cleaner Group; -2 Required | 1 |
| 8N***56 | Filter Element As-Air; (Secondary) | 1 |
| 8N***59 | Gasket-Air Cleaner Cover | 1 |
5n-7904 Air Cleaner Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 48 |
| 20***54 | Bolt; (5/8-11x2.5-In) | 6 |
| 20***55 | Bolt; (5/8-11x2.75-In) | 4 |
4p-9088 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 10 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 8 |
| 13***83 | Air Cleaner Group | 2 |
137-8721 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 6 |
| 13***21 | Air Cleaner Group | 1 |
7e-8228 Air Cleaner Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 6 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 18 |
133-7380 Air Cleaner Gp
| 13***79 | Housing As-Air Cleaner | 1 |
| 13***80 | Air Cleaner Group | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
131-2183 Air Cleaner Gp
| 13***83 | Air Cleaner Group | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 2 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 2 |
9y-5313 Arrestor Gp-Flame
| 10***74 | Arrestor As, .. Bushing | 1 |
| 15***55 | Gasket-Manifold | 1 |
| 9Y***13 | Arrestor Group-Flame | 1 |
146-0758 Bypass Gp-Exhaust
| 10***19 | Base As | 1 |
| 11***72 | Diaphragm | 1 |
| 14***51 | Cover As | 1 |
4w-5947 Bypass Gp-Exhaust
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 14***58 | Bypass Group-Exhaust | 1 |
| 16***00 | Locknut; (High Temperature) | 4 |
4w-2277 Cartridge Gp-Turbocharger
| 15***36 | Shaft As-Turbine | 1 |
| 15***37 | Nut | 1 |
| 1P***11 | Bearing-Thrust | 1 |
133-4817 Conversion Ar-Air Cleaner
| 00***01 | Elbow (To Serial No 1md225) | 1 |
| 03***44 | Elbow)Hose Connection From Check | 1 |
| 03***19 | Elbow | 1 |
8n-8487 Elbow Gp-Exhaust
| 1D***66 | Bolt Bracket Assembly To Yoke | 2 |
| 1D***69 | Bolt 107.95 mm(4.25 In.) Long; Bolt (Plate To Front Housing) | 2 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
5l-7520 Elbow-Exhaust
| 5L***20 | Elbow-Exhaust | 1 |
5n-2458 Elbow-Exhaust
| 5N***58 | Elbow-Exhaust | 1 |
7n-6967 Fitting Gp-Exhaust -Flexible
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 24***12 | Gasket; (Exhaust) | 1 |
| 2B***58 | Plug--To Block Upper Front Air Manifold | 1 |
7n-6968 Fitting Gp-Exhaust
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 3V***08 | Washer-Hard; (10.2x20.5x2.5-mm Thk)(Shield To Head) | 8 |
| 5L***73 | Gasket-Exhaust Elbow | 1 |
5n-2457 Fitting Gp-Exhaust -Flexible
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 8 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 21***45 | Bellows As | 1 |
2w-7863 Flange Gp-Exhaust
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 8 |
| 2W***63 | Flange Group-Exhaust | 1 |
| 2W***64 | Flange-Exhaust | 1 |
2w-7871 Flange Gp-Exhaust
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 12 |
| 1B***55 | Nut,Plain,Hexagon Turbocharger Mounting | 12 |
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 12 |
7n-6962 Flange Gp-Exhaust
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 12 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 12 |
| 7N***54 | Flange | 1 |
2w-7866 Flange Gp-Exhaust
| 1B***57 | Nut-Full; 19.05mm(.75in)O.D. | 12 |
| 2W***66 | Flange Group-Exhaust | 1 |
| 2W***67 | Flange-Exhaust | 1 |
7n-6961 Flange Gp-Exhaust
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 3V***08 | Washer-Hard; (10.2x20.5x2.5-mm Thk)(Shield To Head) | 16 |
| 5L***73 | Gasket-Exhaust Elbow | 1 |
4p-9597 Indicator Gp-Air Filter Change
| 3B***85 | Nipple-Pipe | 1 |
| 4P***97 | Indicator Group-Air Filter Change | 1 |
| 4W***20 | Indicator-Air Filter Change | 2 |
213-1412 Indicator Gp-Air Filter Change
| 21***12 | Indicator Group-Air Filter Change | 1 |
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
7w-1678 Indicator Gp-Air Filter Change
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 4W***20 | Indicator-Air Filter Change | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
7n-6782 Indicator Gp-Air Filter Change
| 3B***52 | Elbow; --Cross To Hose Assembly To Air Gauge | 2 |
| 5L***33 | Fitting (To Air Cleaner) | 2 |
| 6I***33 | Indicator Group-Air Filter Change | 2 |
6i-0666 Lines Gp-Air -Purge
| 00***01 | Elbow (To Serial No 1md225) | 1 |
| 03***50 | Elbow (Check Valve Drain Tube) | 1 |
| 03***19 | Elbow | 1 |
9y-1221 Lines Gp-Air -Carburetor Inlet
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 4 |
| 4W***02 | Gasket | 1 |
9y-0779 Lines Gp-Turbocharger Air -Turbocharger To Aftercooler
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 2 |
9y-0781 Manifold Gp-Exhaust
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 16 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***19 | Plug-Cup | 2 |
4p-8330 Manifold Gp-Inlet
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 18 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 10 |
214-6133 Mounting Gp-Air Cleaner
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 6 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 12 |
| 21***33 | Mounting Group-Air Cleaner | 1 |
4w-6341 Mounting Gp-Air Cleaner
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 1K***49 | Spacer Alternator To Brackets | 1 |
206-7137 Mounting Gp-Air Cleaner
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 1K***49 | Spacer Alternator To Brackets | 1 |
2w-4075 Muffler
| 2W***75 | Muffler | 1 |
2w-4073 Muffler
| 2W***73 | Muffler | 1 |
152-0596 Muffler Gp-Spark Arrestor
| 15***96 | Muffler Group-Spark Arrestor | 1 |
5n-7831 Precleaner Gp
| 2M***79 | Seal-O-Ring | 1 |
| 5N***31 | Precleaner Group | 1 |
| 5N***33 | Body As | 1 |
127-4516 Turbocharger Gp
| 10***16 | Plug-Cup | 4 |
| 12***16 | Turbocharger Group | 1 |
| 13***02 | Cartridge Group-Turbocharger | 1 |
7e-8464 Turbocharger Gp
| 12***36 | Gasket; (Turbocharger) | 2 |
| 16***00 | Locknut; (High Temperature) | 8 |
| 2A***39 | Bolt,Machine Tube To Torque Converter And Tube To Oil Cooler | 8 |
7e-8465 Turbocharger Gp
| 1B***74 | Plug,Pipe Base Assembly,Engine Oil Filter Assembly | 2 |
| 1C***69 | Bolt (1/2 In. Long 5/16 In. Dia.); Support Assembly To Heater Group | 6 |
| 1P***12 | Clamp; (Turbine) | 3 |
138-4183 Turbocharger Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 12***36 | Gasket; (Turbocharger) | 2 |
| 12***16 | Turbocharger Group | 2 |
8n-8483 Valve Gp-Air Control -Rh
| 1L***73 | Valve Group-Pressure Reducing; -Rh | 1 |
| 3L***93 | Nipple-Close; (1 1/2-11 1/2 Npt Thd) | 1 |
| 5B***66 | Elbow; (90 Degree, 1-1/2-11-1/2 Npt) | 1 |
4w-5424 Valve Gp-Air Control
| 2W***20 | Valve-Control | 1 |
| 32***82 | Knob | 1 |
| 4W***24 | Valve Group-Air Control; (Engine Start Control) | 1 |
Basic Engine
7n-8711 Balancer Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 10***65 | Plate-Thrust | 1 |
| 4W***98 | Shaft-Cluster Gear | 1 |
253-2468 Barring Gp -Rh
| 25***68 | Barring Group; -Rh | 1 |
| 3R***37 | Device-Barring | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
5r-7425 Barring Gp -Lh
| 3R***37 | Device-Barring | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
| 5R***25 | Barring Group; Barring Group-Engine | 1 |
114-2903 Camshaft Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 10***58 | Camshaft; (Rh) | 1 |
5n-3765 Coupling Gp-Flexible -Viscous Dampened
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 12 |
| 1A***37 | Bolt Clutch Assembly To Bracket (Fan Support) | 12 |
| 3N***66 | Coupling-Drive | 1 |
268-6475 Coupling Gp-Flexible -Generator
| 24***08 | Coupling Group-Flexible; -Generator | 1 |
| 26***75 | Coupling Group-Flexible; -Generator | 1 |
| 4M***53 | Washer-Hard; (24x38x3.5-mm Thk) | 8 |
247-0308 Coupling Gp-Flexible -Generator
| 24***91 | Coupling; (Outer) | 1 |
| 24***08 | Coupling Group-Flexible; -Generator | 1 |
| 24***32 | Washer; (17x30x3-mm Thk) | 12 |
8n-7152 Coupling Gp-Flexible
| 1D***85 | Cap Screw (3 1/4" Long) | 12 |
| 5N***78 | Plate As | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
153-0395 Coupling Gp-Generator
| 15***95 | Coupling Group-Generator | 1 |
| 5N***93 | Plate Group-Generator Coupling | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
3n-8594 Cover Gp-Engine Lifting Eye
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 1 |
| 3N***93 | Cover-Eye | 1 |
| 3N***94 | Cover Group | 1 |
4p-8325 Cover Gp-Cylinder Block -Central Structure
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 36 |
| 1N***14 | Cover-Cylinder Block Side | 8 |
225-7845 Cover Gp-Engine Lifting Eye
| 22***45 | Cover Group-Engine Lifting Eye | 1 |
| 22***46 | Cover-Lifting Eye | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 1 |
226-1771 Cover Gp-Engine Lifting Eye
| 22***71 | Cover Group-Engine Lifting Eye | 1 |
| 22***81 | Cover-Lifting Eye | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 1 |
4p-8309 Cover Gp-Flywheel Housing
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
4p-8304 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 24 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 23***46 | Seal-O-Ring | 1 |
4w-4839 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 34 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 1C***51 | Bolt--Installation Of 2v***26 Retainer | 1 |
4p-8305 Cover Gp-Front Housing
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 17 |
| 1B***18 | Washer; (25/64 X 5/8 X .064in Thk) | 6 |
| 23***46 | Seal-O-Ring | 1 |
2w-5616 Cover Gp-Oil Pan
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***64 | Cover As | 1 |
| 2W***16 | Cover Group-Oil Pan | 1 |
4p-8310 Cover Gp-Valve Mechanism
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 27***57 | Seal; (Valve Cover To Breather) | 1 |
| 4P***10 | Cover Group-Valve Mechanism | 1 |
226-1781 Cover-Lifting Eye
| 22***81 | Cover-Lifting Eye | 1 |
225-7846 Cover-Lifting Eye
| 22***46 | Cover-Lifting Eye | 1 |
7n-8707 Crankshaft Gp
| 12***45 | Bolt As; (5/8-18x4.25-In)(Counterweight) | 18 |
| 14***31 | Bearing As-Main; (Standard) | 5 |
| 14***32 | Bearing-Main; (0.63-mm Us Id) | 0 |
106-2778 Cylinder Block As
| 10***78 | Cylinder Block As | 1 |
| 22***96 | Cap-Crankshaft Bearing | 5 |
| 4W***13 | Plug; (2-1/4-12 Thd) | 2 |
101-1171 Cylinder Block As
| 10***71 | Cylinder Block As | 1 |
| 21***26 | Liner-Cylinder Block | 8 |
| 22***96 | Cap-Crankshaft Bearing | 5 |
115-3503 Cylinder Block Gp
| 03***42 | Seal-O-Ring; (11.89mm Id) | 6 |
| 10***78 | Cylinder Block As | 1 |
| 11***03 | Cylinder Block Group | 1 |
115-3502 Cylinder Block Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 2 |
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 8 |
| 10***71 | Cylinder Block As | 1 |
4p-6571 Cylinder Head As
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 5 |
| 3B***45 | Plug Flywheel Housing Turbocharger Drain Hole | 5 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 2 |
4p-8300 Cylinder Head As
| 4P***71 | Cylinder Head As | 1 |
| 4P***00 | Cylinder Head As | 1 |
| 7N***02 | Dowel | 2 |
206-1556 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 2 |
| 19***66 | Guide-Valve; (Inlet)(Standard) | 2 |
| 19***99 | Rotocoil As | 4 |
206-1555 Cylinder Head Gp
| 19***60 | Insert-Valve Seat; (Exhaust)(Standard) | 2 |
| 20***46 | Insert-Valve Seat; (Exhaust 0.254-mm Os Od) | 0 |
| 20***47 | Insert-Valve Seat; (Exhaust 0.508-mm Os Od) | 0 |
4p-6570 Cylinder Head Gp
| 10***84 | Valve-Exhaust & Inlet | 4 |
| 13***14 | Rotocoil As | 4 |
| 2A***29 | Lock,Valve Spring R Cylinder Head | 8 |
206-1558 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 13***20 | Fastener Group-Cylinder Head | 6 |
| 13***21 | Fastener Group-Cylinder Head | 2 |
4p-6569 Cylinder Head Gp
| 11***91 | Gasket-Cylinder Head | 1 |
| 12***12 | Seal-Water; (11.2mm Id) | 4 |
| 12***13 | Seal-Water; (21.2mm Id) | 4 |
8n-7182 Damper Gp
| 19***88 | Damper As | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 10 |
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
4w-0278 Damper Gp
| 19***88 | Damper As | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 10 |
| 3B***15 | Bolt Guard Assembly To Accessory Drive Housing | 18 |
202-8640 Drain Gp-Engine Oil -Rear
| 20***40 | Drain Group-Engine Oil; -Rear | 1 |
| 3B***70 | Nipple,Pipe Hose To Flange | 1 |
| 3B***45 | Nipple-Pipe; (3/4-14 Npt Thd)(Both Ends) | 1 |
9y-7876 Drain Gp-Engine Oil -Pan
| 1F***60 | Nipple-Pipe | 1 |
| 3E***30 | Plug-Pipe; (3/4-14 Nptf) | 1 |
| 6F***68 | Gasket; (Oil Pan) | 1 |
110-6206 Drain Gp-Engine Oil
| 11***06 | Drain Group-Engine Oil | 1 |
| 11***07 | Valve; (Engine Oil Drain) | 1 |
| 3B***96 | Fitting; (Nipple) | 1 |
216-7097 Drive Gp-Accessory -Upper, Rh
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 21***97 | Drive Group-Accessory; -Upper, Rh | 1 |
| 5P***47 | Washer (Bracket To Valve Support) | 2 |
7n-4871 Drive Gp-Accessory -Upper, Rh
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 2 |
8n-9166 Drive Gp-Accessory -Upper, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 12***00 | Bearing-Sleeve | 2 |
8n-5678 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
8n-9167 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
155-8502 Gear Gp-Front
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
7e-7647 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
| 12***00 | Bearing-Sleeve | 1 |
1w-9553 Drive Gp-Accessory -Lower, Lh
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
| 11***65 | Bearing | 1 |
3n-8647 Fastener Gp-Coupling
| 20***99 | Bolt-12 Point Head; (7/8-9x3-In) | 8 |
| 3N***47 | Fastener Group-Coupling; Fastener Group--Shaft And Hub | 1 |
| 8C***13 | Washer-Hard; (24x41.5x4-mm Thk) | 8 |
2w-8772 Flywheel Gp
| 23***43 | Gear-Flywheel; (183-Teeth) | 1 |
| 24***19 | Flywheel As | 1 |
| 2W***72 | Flywheel Group | 1 |
122-9281 Gear Gp-Front -Low Speed, Standard Rotation
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 2 |
8n-7174 Gear Gp-Front -Standard Rotation
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 5 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
112-5677 Gear Gp-Rear
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
| 10***65 | Plate-Thrust | 1 |
| 10***68 | Washer-Thrust; (19.50 X 106 X 1.9mm Thk) | 2 |
7w-5780 Guard Gp-Belt -Alternator
| 27***35 | Spacer; (13.87x21.34x11-mm Thk) | 2 |
| 28***74 | Guard As-Alternator | 1 |
| 7W***80 | Guard Group-Belt; -Alternator | 1 |
271-9270 Guard Gp-Belt -Alternator
| 21***41 | Spacer; (13.9x21.3x8-mm Thk) | 2 |
| 26***27 | Plate As | 1 |
| 27***70 | Guard Group-Belt; -Alternator | 1 |
151-9228 Guard Gp-Belt -Alternator
| 15***28 | Guard Group-Belt; -Alternator | 1 |
| 17***59 | Guard As-Belt; (Alternator) | 1 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 1 |
307-1569 Guard Gp-Belt -Alternator
| 30***32 | Guard-Alternator | 1 |
| 30***69 | Guard Group-Belt; -Alternator | 1 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 1 |
3n-5765 Guard Gp-Coupling -Flywheel
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 10 |
| 1V***23 | Plate | 2 |
203-9448 Guard Gp-Damper
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 6 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 8 |
8n-9639 Guard Gp-Damper
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 6 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 8 |
4p-8307 Housing Gp-Flywheel
| 1A***69 | Bolt (R.H. Side Flywheel Housing) | 2 |
| 1D***90 | Bolt 4.75 In.(120.65 mm) Long | 16 |
| 22***19 | Housing-Flywheel | 1 |
7w-3724 Housing Gp-Front -Accessory Drive
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 10***34 | Housing-Accessory Drive | 1 |
| 1D***93 | Bolt 5.5 In. (13.97 cm) Long | 10 |
3n-5596 Hub-Flexible Coupling
| 3N***96 | Hub-Flexible Coupling | 1 |
4w-5450 Lifting Gp-Engine
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 4 |
| 15***26 | Bracket As | 2 |
| 4W***50 | Lifting Group-Engine | 1 |
7e-4836 Mounting Gp-Alternator
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 14***16 | Belt-Serpentine; (Alternator) | 1 |
| 1A***68 | Bolt 7.50 In. (19.05 cm) Long | 1 |
8n-9567 Mounting Gp-Engine Flexible
| 15***65 | Mount As | 6 |
| 5P***97 | Washer; (17x45x6-mm Thk) | 6 |
| 8N***67 | Mounting Group-Engine Flexible | 1 |
8n-9570 Mounting Gp-Engine Flexible
| 5P***97 | Washer; (17x45x6-mm Thk) | 8 |
| 8N***70 | Mounting Group-Engine Flexible | 1 |
| 8N***70 | Mount Assem. (Generator Set) | 8 |
9y-3086 Pan Gp-Oil
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
7c-6887 Pan Gp-Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 18 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 26 |
133-9376 Piston & Rod Gp
| 10***30 | Bearing-Connecting Rod; (Standard) | 1 |
| 10***31 | Bearing-Connecting Rod; (0.63-mm Us Id) | 0 |
| 10***32 | Bearing-Connecting Rod; (1.27-mm Us Id) | 0 |
126-9496 Piston & Rod Gp
| 10***30 | Bearing-Connecting Rod; (Standard) | 1 |
| 10***31 | Bearing-Connecting Rod; (0.63-mm Us Id) | 0 |
| 10***32 | Bearing-Connecting Rod; (1.27-mm Us Id) | 0 |
102-2256 Piston & Rod Gp
| 10***40 | Body As-Piston | 1 |
| 10***56 | Piston & Rod Group | 1 |
| 10***30 | Bearing-Connecting Rod; (Standard) | 1 |
6i-4610 Piston & Rod Gp
| 10***30 | Bearing-Connecting Rod; (Standard) | 1 |
| 10***31 | Bearing-Connecting Rod; (0.63-mm Us Id) | 0 |
| 10***32 | Bearing-Connecting Rod; (1.27-mm Us Id) | 0 |
7n-4106 Pulley As-Crankshaft
| 4W***35 | Kit-Bushing; (Crankshaft Pulley) | 1 |
| 7N***06 | Pulley As-Crankshaft | 1 |
8n-6564 Pulley As-Crankshaft
| 4W***35 | Kit-Bushing; (Crankshaft Pulley) | 1 |
| 8N***64 | Pulley As-Crankshaft | 1 |
7w-3813 Seal Gp-Crankshaft
| 11***32 | Seal Group-Crankshaft; (Cw Rotation) | 1 |
| 11***33 | Seal Group-Crankshaft; (Ccw Rotation) | 1 |
| 7W***13 | Seal Group-Crankshaft | 1 |
7n-7660 Drive Gp-Fan
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
| 7N***57 | Shaft-Stub | 1 |
| 7N***60 | Shaft Group-Stub; -Crankshaft Pulley | 1 |
150-7947 Shaft Gp-Stub
| 14***83 | Shaft-Stub | 1 |
| 15***47 | Shaft Group-Stub | 1 |
| 5P***50 | Washer-Front Support Frame Assembly To | 6 |
5n-4830 Valve Gp-Explosion Relief -Crankcase
| 27***59 | Seal | 1 |
| 2W***84 | Kit-Repair; (Explosion Relief)(Crankcase) | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
1w-8465 Valve Mechanism Gp
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 12***81 | Bridge As | 2 |
| 13***49 | Base As | 1 |
Cooling System
9y-8179 Connection Gp-Water -Inlet, Outlet
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
4p-7072 Connection Gp-Water -Outlet, Lh
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
8n-8993 Connection Gp-Water -Inlet, Lh
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 16 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 1S***72 | Gasket | 2 |
7w-6372 Connection Gp-Water -Outlet
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 12 |
4w-5893 Cooler Gp-Engine Oil
| 10***32 | Seal-O-Ring | 2 |
| 12***42 | Core As-Oil Cooler; (Engine) | 1 |
| 1A***83 | Bolt (4.75" Long-Location "B") | 3 |
6i-0999 Flange Gp-Coolant Lines
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 8 |
| 1S***72 | Gasket | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 8 |
7n-4885 Switch Gp-Coolant Level
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 2 |
| 2N***68 | Switch-Liquid Level; (Coolant) | 1 |
| 3N***22 | Hose Assem. 29.6 cm(11.65 In.) | 2 |
3n-8889 Heat Exchanger Gp-Sea Water
| 2N***63 | Flange | 2 |
| 3N***88 | Heat Exchanger Group; Heat Exchanger Group-High Capacity | 1 |
| 3N***89 | Heat Exchanger Group; Heat Exchanger Group-High Capacity | 1 |
3n-8888 Heat Exchanger Gp-Sea Water
| 0T***20 | Bolt (1.25 In. Long X .438 In. Dia.) | 12 |
| 0T***68 | Bolt,Machine; Tube Mounting And Tube To Junction Block Uoc:Bsv,Bsx | 12 |
| 1H***00 | Pin--To Compression Release Shaft | 1 |
150-0372 Housing & Regulator Gp -Coolant
| 15***72 | Housing & Regulator Group; -Coolant | 1 |
| 15***17 | Regulator As-Water Temperature; (110-Deg F) | 1 |
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
9y-9090 Housing & Regulator Gp -Outlet Control
| 11***74 | Valve As-Vent Line | 1 |
| 15***10 | Seal-Integral; (Water Temperature Regulator) | 1 |
| 24***33 | Regulator-Water Temperature; (98-Deg C)(Water, Coolant) | 4 |
170-7707 Housing & Regulator Gp
| 17***07 | Housing & Regulator Group | 1 |
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 2 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 2 |
7w-1497 Housing & Regulator Gp -Coolant
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 1 |
| 4P***03 | Housing-Upper | 1 |
7w-6555 Housing & Regulator Gp -Coolant
| 1Y***62 | Washer; (0.328x0.81x0.125-In Thk) | 1 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 1 |
| 4P***03 | Housing-Upper | 1 |
5p-9130 Joint As-Tube
| 5P***30 | Joint As-Tube | 1 |
| 9X***40 | Seal; (140.46mm Id) | 2 |
130-7222 Lines Gp-Auxiliary Fresh Water -Aftercooler
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
4p-3528 Lines Gp-Auxiliary Fresh Water -Aftercooler
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 8 |
7e-8457 Lines Gp-Turbocharger Water
| 00***04 | Fitting-Flared | 1 |
| 00***42 | Elbow | 2 |
| 00***25 | Elbow-Flared | 1 |
122-8619 Lines Gp-Vent
| 00***81 | Tee-Union; (Flared 37-Deg) | 1 |
| 01***24 | Bushing To Supply Port | 2 |
| 03***45 | Reducer-Flared | 1 |
121-3119 Lines Gp-Vent
| 00***81 | Tee-Union; (Flared 37-Deg) | 1 |
| 01***24 | Bushing To Supply Port | 2 |
| 03***45 | Reducer-Flared | 1 |
133-3689 Lines Gp-Water -Manifold
| 00***62 | Seal-O-Ring; (63.17mm Id) | 1 |
| 03***69 | Elbow-Flared; (1/2-14 Nptf) | 2 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 2 |
115-6434 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 19 |
| 11***34 | Lines Group-Water; -Bypass | 1 |
9y-9185 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
1n-4171 Lines Gp-Water -Lower
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***21 | Adapter | 1 |
309-0103 Lines Gp-Water -Bypass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 9 |
| 1D***06 | Bolt; (3/8-16x6-In)(Locations Y) | 3 |
4p-8322 Lines Gp-Water -Upper
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 18 |
4w-5771 Lines Gp-Water -Turbocharger Exhaust
| 00***04 | Fitting-Flared | 2 |
| 00***42 | Elbow | 1 |
| 00***25 | Elbow-Flared | 1 |
2w-1464 Lines Gp-Water -Upper
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 4 |
290-6399 Lines Gp-Water -Bybass
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
7e-9781 Pump Gp-Auxiliary Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
1w-9554 Pump Gp-Auxiliary Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 7 |
| 1T***32 | Seal-O-Ring; (234.54mm Id) | 1 |
| 1T***65 | Bolt 2.54 cm (1" Long) | 1 |
212-8169 Pump Gp-Auxiliary Water -Fresh Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***69 | Pump Group-Auxiliary Water; -Fresh Water | 1 |
291-4313 Pump Gp-Auxiliary Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***00 | Bearing-Sleeve | 1 |
| 21***79 | Shaft; (14-Teeth) | 1 |
2w-9726 Pump Gp-Water
| 14***62 | Seal-O-Ring | 1 |
| 21***76 | Pump Group-Water | 1 |
| 22***53 | Kit-Rebuild; (Water Pump) | 0 |
212-8176 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
166-4377 Pump Gp-Water
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 16***74 | Ring As | 1 |
| 16***76 | Seal Group-Water Pump; (Face Type) | 1 |
7e-4802 Regulator Gp-Temperature -Aftercooler
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 17***07 | Housing & Regulator Group | 1 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 2 |
7w-1427 Regulator Gp-Temperature
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
8n-7643 Housing & Regulator Gp -Inlet Control
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 5 |
| 10***12 | Plate | 2 |
| 1A***83 | Bolt (4.75" Long-Location "B") | 5 |
212-6938 Tank Gp-Expansion
| 20***25 | Tank Group-Expansion | 1 |
| 21***38 | Tank Group-Expansion | 1 |
| 2W***64 | Lines Group-Water; -Upper | 1 |
201-3425 Tank Gp-Expansion
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 11***74 | Valve As-Vent Line | 1 |
8n-7717 Tank Gp-Expansion
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
4p-4694 Tank Gp-Expansion
| 2W***64 | Lines Group-Water; -Upper | 1 |
| 4P***94 | Tank Group-Expansion | 1 |
| 8N***43 | Regulator Group-Temperature; -Inlet Control | 1 |
212-6936 Tank Gp-Water -Coolant Overflow
| 06***37 | Union-Flared | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 8 |
120-8876 Tank Gp-Water -Coolant Overflow
| 06***37 | Union-Flared | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 8 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 9 |
Electrical And Starting System
7c-2700 Control Gp-Manual Voltage
| 7C***00 | Module-Control | 1 |
6n-9294 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 5 |
| 11***19 | Diode As-Alternator | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
4n-3986 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
| 10***62 | Kit-Alternator Terminal | 1 |
331-5717 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
266-7227 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
112-3454 Alternator Gp-Charging
| 11***54 | Alternator Group-Charging | 1 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
| 6N***94 | Alternator Group; (24-Volt, 35-Ampere) | 1 |
112-3455 Alternator Gp-Charging
| 09***19 | Washer; (7.14x15.88x1.58-mm Thk) | 2 |
| 11***55 | Alternator Group-Charging | 1 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
7n-7981 Alternator Gp-Charging
| 09***19 | Washer; (7.14x15.88x1.58-mm Thk) | 2 |
| 2L***73 | Fitting; (Rubber)(Used Only On Positive Pole) | 1 |
| 2N***79 | Machine Screw--Wire Assembly To Panel | 1 |
7c-3874 Battery Charger
| 7C***74 | Battery Charger; Battery Charger-24 Volt, Dc With Failure | 1 |
7w-0408 Battery Charger
| 7W***08 | Battery Charger; Battery Charger--24 Volt Dc | 1 |
131-0832 Battery Charger Gp
| 13***32 | Battery Charger Group | 1 |
| 13***72 | Fuse; (12-Ampere) | 1 |
| 13***74 | Fuse; (15-Ampere) | 1 |
7l-7872 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
7l-7871 Battery Gp
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 2 |
| 2V***97 | Cable Assem. | 1 |
197-8858 Block Gp-Junction
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***18 | Cover-Terminal | 2 |
122-1194 Box & Mounting Gp -Cable Access
| 12***94 | Box & Mounting Group; -Cable Access | 1 |
| 12***33 | Frame As-Box | 1 |
| 12***35 | Cover-Top | 1 |
120-9189 Box As-Extension -Circuit Breaker
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 10 |
| 12***89 | Cover As-Top | 1 |
| 12***89 | Box As-Extension; -Circuit Breaker | 1 |
115-2513 Box Gp-Extension Terminal -Circuit Breaker
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 10 |
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***34 | Cover As-Top | 1 |
141-1808 Box Gp-Generator Connection
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 18 |
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 2 |
120-9193 Bracket As-Circuit Breaker -Circuit Breaker
| 12***93 | Bracket As-Circuit Breaker; -Circuit Breaker | 1 |
252-7458 Bus Bar As
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 6 |
| 20***43 | Bolt; (M12x1.75x42.5-mm) | 12 |
| 25***58 | Bus Bar As | 1 |
121-0280 Cable As-Extension
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***80 | Cable As-Extension | 1 |
120-9195 Cable As-Extension
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 1 |
7w-0825 Cable Gp-Battery
| 1M***19 | Bolt; (5/16-18x1.375-In)(5/16-18x1.375 In) | 2 |
| 1M***20 | Nut-Battery Terminal (5/16-18 Thd); (5/16-18-Thd)(5/16-18x1.375 In) | 1 |
| 1S***51 | Terminal-Cable; (00-Ga, 1/2-In Screw) | 2 |
122-0332 Cable Gp -Circuit Breaker Connection
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 24 |
| 12***32 | Cable Group; -Circuit Breaker Connection | 1 |
252-7538 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***32 | Circuit Breaker Group | 1 |
252-7537 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***31 | Circuit Breaker Group | 1 |
252-7534 Circuit Breaker & Mounting Gp
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 25***20 | Plate | 2 |
| 25***30 | Circuit Breaker Group | 1 |
252-7539 Circuit Breaker & Mounting Gp
| 10***97 | Bar-Circuit Breaker; (3200-Ampere) | 2 |
| 10***16 | Bar-Circuit Breaker; (3200-Ampere) | 3 |
| 10***18 | Bar-Circuit Breaker; (3200-Ampere) | 1 |
270-4565 Circuit Breaker As
| 24***30 | Kit-Bolt; (Circuit Breaker) | 1 |
| 24***27 | Fastener Group; (Bus Bar Box) | 3 |
| 24***50 | Terminal-Circuit Breaker | 1 |
105-7933 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***33 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
4p-3840 Circuit Breaker As
| 4P***40 | Circuit Breaker As | 1 |
| 4P***42 | Circuit Breaker As; (1600-Ampere) | 1 |
7c-0229 Circuit Breaker As
| 3N***85 | Circuit Breaker 1200 Amperes Derated | 1 |
| 7C***29 | Circuit Breaker As | 1 |
270-4537 Circuit Breaker As -1200-Ampere
| 24***30 | Kit-Bolt; (Circuit Breaker) | 1 |
| 24***27 | Fastener Group; (Bus Bar Box) | 3 |
| 24***47 | Terminal-Circuit Breaker | 1 |
7c-0228 Circuit Breaker As
| 5N***58 | Circuit Breaker 1000 Amperes Derated | 1 |
| 7C***28 | Circuit Breaker As | 1 |
4p-3841 Circuit Breaker As
| 4P***41 | Circuit Breaker As | 1 |
| 4P***43 | Circuit Breaker As; (1600-Ampere) | 1 |
105-7934 Circuit Breaker As
| 10***32 | Switch As-Auxiliary | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
7c-0230 Circuit Breaker As
| 5N***57 | Circuit Breaker 1200 Amperes Derated | 1 |
| 7C***30 | Circuit Breaker As | 1 |
7c-0227 Circuit Breaker As
| 3N***84 | Circuit Breaker 1000 Amperes Derated | 1 |
| 7C***27 | Circuit Breaker As | 1 |
105-7926 Circuit Breaker Gp
| 10***26 | Circuit Breaker Group | 1 |
| 10***33 | Circuit Breaker As | 1 |
| 10***05 | Bar; (1600-Ampere) | 3 |
252-7531 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***31 | Circuit Breaker Group | 1 |
| 27***59 | Circuit-Breaker; (2000-Ampere) | 1 |
105-7928 Circuit Breaker Gp
| 10***28 | Circuit Breaker Group | 1 |
| 10***34 | Circuit Breaker As | 1 |
| 10***99 | Bar-Circuit Breaker | 3 |
207-1740 Circuit Breaker Gp
| 10***26 | Circuit Breaker Group | 1 |
| 20***40 | Circuit Breaker Group | 1 |
252-7533 Circuit Breaker Gp
| 25***57 | Bus As; (3200-Ampere) | 2 |
| 25***29 | Circuit Breaker As; (3200-Ampere) | 1 |
| 25***33 | Circuit Breaker Group | 1 |
7w-9640 Circuit Breaker Gp
| 3K***06 | Screw-Machine-Relay To Bracket | 2 |
| 4B***63 | Washer; (4.7x11x1.2-mm Thk) | 2 |
| 6T***45 | Circuit Breaker Group; -60-Ampere | 1 |
106-5659 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***59 | Circuit Breaker Group | 1 |
| 10***65 | Circuit Breaker As; (800-Ampere) | 1 |
114-4674 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 11***74 | Circuit Breaker Group | 1 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 9 |
106-5660 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***60 | Circuit Breaker Group | 1 |
| 10***66 | Circuit Breaker As; (1000-Ampere) | 1 |
106-5663 Circuit Breaker Gp
| 10***34 | Circuit Breaker Group; (1000-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***63 | Circuit Breaker Group | 1 |
106-5664 Circuit Breaker Gp
| 10***35 | Circuit Breaker Group; (1200-Ampere) | 1 |
| 10***80 | Shunt | 1 |
| 10***64 | Circuit Breaker Group | 1 |
252-7530 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***30 | Circuit Breaker Group | 1 |
| 27***58 | Circuit-Breaker; (1600-Ampere) | 1 |
270-4658 Circuit Breaker Gp
| 10***95 | Bar As | 2 |
| 10***96 | Bar As | 1 |
| 27***37 | Circuit Breaker As; -1200-Ampere | 1 |
106-5661 Circuit Breaker Gp
| 10***80 | Shunt | 1 |
| 10***61 | Circuit Breaker Group | 1 |
| 10***67 | Circuit Breaker As; (1200-Ampere) | 1 |
270-4615 Circuit Breaker Gp
| 27***55 | Bar As | 2 |
| 27***56 | Bar As | 1 |
| 27***65 | Circuit Breaker As | 1 |
252-7532 Circuit Breaker Gp
| 25***58 | Bus Bar As | 2 |
| 25***32 | Circuit Breaker Group | 1 |
| 27***60 | Circuit Breaker As; (2500-Ampere) | 1 |
105-7927 Circuit Breaker Gp
| 10***27 | Circuit Breaker Group | 1 |
| 10***32 | Switch As-Auxiliary | 1 |
| 10***38 | Contactor-Shunt; (24-Vdc) | 1 |
121-8855 Connection Gp-Electrical
| 12***55 | Connection Group-Electrical | 1 |
| 16***12 | Wire As-Ground | 1 |
| 17***97 | Strip Group-Terminal; -Ac | 1 |
121-9638 Connection Gp-Electrical
| 11***42 | Strip As | 1 |
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 4F***57 | Screw,Cap,Hexagon H Shock Mount To Bracket | 2 |
103-8974 Connection Gp-Electrical
| 10***74 | Connection Group-Electrical | 1 |
| 10***80 | Film-Identification; (Terminal Marker) | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 20 |
121-9639 Connection Gp-Electrical -Thermocouple
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 17***95 | Strip Group-Terminal; -Thermocouple | 1 |
108-0726 Connection Gp-Electrical
| 10***26 | Connection Group-Electrical | 1 |
| 10***80 | Film-Identification; (Terminal Marker) | 1 |
| 2F***47 | Screw-Machine | 6 |
4p-4634 Connection Gp-Electrical
| 03***43 | Screw; (1/4-20x0.625-In) | 2 |
| 17***97 | Strip Group-Terminal; -Ac | 1 |
| 2N***80 | Screw-Machine; (10-24x0.75-In) | 2 |
121-9640 Connection Gp-Electrical -Rtd
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
7c-6795 Connection Gp-Electrical
| 2F***47 | Screw-Machine | 6 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 30 |
| 4D***60 | Strip-Terminal; 21.4cm(8.44in)Lg | 3 |
218-4826 Connection Gp-Electrical -Terminal Block, Rtd
| 16***89 | Bracket-End | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
| 20***44 | Transformer As-Current | 1 |
5n-2126 Connector -Thermocouple
| 5N***26 | Connector; Adapter-.25in Pipe Thread | 1 |
5n-8857 Contactor As-Water Temp
| 5N***57 | Contactor As-Water Temp | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
237-1971 Contactor Gp-Generator -Jacket Water Heater
| 23***71 | Contactor Group-Generator; -Jacket Water Heater | 1 |
| 23***24 | Contactor | 1 |
104-2250 Control & Cover Gp-Eng Elek
| 00***40 | Connector; (Flared) | 1 |
| 03***93 | Adaptor (5wd1-200 And 4sd1-159). | 1 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
154-3850 Control & Cover Gp-Eng Elek
| 03***39 | Seal-O-Ring (Id=9.25mm) | 1 |
| 10***50 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 14***62 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
4p-9565 Control & Cover Gp-Eng Elek
| 00***40 | Connector; (Flared) | 1 |
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 03***39 | Seal-O-Ring (Id=9.25mm) | 1 |
121-5502 Control Gp-Engine Electronic
| 12***24 | Bracket As | 4 |
| 12***02 | Control Group | 1 |
| 13***11 | Junction Box | 1 |
7c-0330 Control Gp-Air Starting
| 2V***56 | Hose Assem. 53.4 cm (21.02 In.) | 1 |
| 4M***17 | Bushing-Reducing; (For Use With Ta Exhaust Man.) | 1 |
| 5F***34 | Valve As-Vent; (Governor Air Compressor) | 1 |
4w-7207 Control Gp-Air Starting -Lh
| 06***95 | Elbow (Between Fuel Lines) | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
147-8337 Control Gp-Air Starting
| 13***77 | Valve Group-Solenoid; -Air Start-Air Starting | 1 |
| 14***37 | Control Group-Air Starting | 1 |
| 2V***56 | Hose Assem. 53.4 cm (21.02 In.) | 1 |
154-3853 Control Gp-Air Starting
| 14***37 | Control Group-Air Starting | 1 |
| 15***53 | Control Group-Air Starting | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
4w-7201 Control Gp-Air Starting -Rh
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
256-7512 Control Gp-Communication -Pl1000e
| 25***12 | Control Group-Communication; -Pl1000e | 1 |
| 33***85 | Film-Warning; (Csa Control Panel Approval) | 1 |
256-7511 Control Gp-Communication -Pl1000t
| 25***11 | Control Group-Communication; -Pl1000t | 1 |
| 33***85 | Film-Warning; (Csa Control Panel Approval) | 1 |
5n-0591 Control Gp-Manual Voltage
| 5N***91 | Control Group-Electronic | 1 |
| 5N***03 | Varistor As | 1 |
| 5N***05 | Plate-Switch | 1 |
9y-6496 Module Gp-Interface
| 6V***75 | Track-Relay; (34-cm) | 0 |
| 6V***87 | Screw-Pan Head; (10-24x1-In) | 2 |
| 8K***44 | Fuse; (1-Ampere) | 10 |
4p-8888 Control Gp-Engine Electronic
| 4P***88 | Control Group-Engine Electronic | 1 |
| 4P***65 | Control & Cover Group-Eng Elek | 1 |
| 4P***95 | Wiring Group-Eis | 1 |
132-4370 Control Gp-Engine Electronic
| 13***70 | Control Group-Engine Electronic | 1 |
| 16***34 | Module Group-System Communication | 1 |
205-0628 Control Gp-Engine Electronic
| 10***87 | Bolt; (M5x0.8x12-mm) | 2 |
| 20***28 | Control Group-Engine Electronic | 1 |
| 2H***15 | Washer; (0.219x0.41x0.031-In Thk) | 4 |
109-7034 Control Gp-Jacket Water Heater
| 10***34 | Control Group-Jacket Water Heater | 1 |
| 3E***64 | Switch Group-Temperature; -Coolant | 1 |
| 3T***48 | Clip Assembly - Housing Plug To Housing Recp. | 1 |
318-6263 Conversion Ar
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
| 15***81 | Relay Group; -Engine Failure | 1 |
158-6172 Conversion Ar
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
| 15***72 | Conversion Ar | 1 |
158-6171 Conversion Ar
| 11***75 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
| 15***71 | Conversion Ar | 1 |
118-7851 Cover-Extension Box
| 11***51 | Cover-Extension Box | 1 |
128-1480 Box Gp-Extension Terminal
| 12***80 | Frame Group-Generator Connection | 1 |
| 1D***72 | Bolt-Carriage; (1/2-13x5.5-In) | 6 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 6 |
270-1732 Harness As-Control -Pl1000t
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
276-0785 Harness As-Control -Pl1000e
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
109-4687 Harness As-Engine
| 09***26 | Splice | 3 |
| 09***04 | Tube-Heat Shrink; (19.1-mm Dia)(6-cm) | 0 |
| 10***49 | Locknut; (1-1/4-11-1/2 Nptf-Thd) | 1 |
129-1631 Harness As-Engine
| 12***31 | Harness As-Engine | 1 |
129-1628 Harness As-Engine
| 12***28 | Harness As-Engine | 1 |
129-1634 Harness As-Engine
| 12***34 | Harness As-Engine | 1 |
122-6072 Harness As-Panel -Eis, Interconnect
| 12***72 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8753 Harness As-Panel -Eis, Interconnect
| 11***53 | Harness As-Panel; -Eis, Interconnect | 1 |
282-0917 Harness As-Panel -Product Link
| 10***38 | End-Wire; (16-Ga) | 10 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
116-8756 Harness As-Panel -Eis, Interconnect
| 11***56 | Harness As-Panel; -Eis, Interconnect | 1 |
118-0474 Harness As-Panel -Eis, Interconnect
| 11***74 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8752 Harness As-Panel -Eis, Interconnect
| 11***52 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8754 Harness As-Panel -Eis, Interconnect
| 11***54 | Harness As-Panel; -Eis, Interconnect | 1 |
116-8755 Harness As-Panel -Eis, Interconnect
| 11***55 | Harness As-Panel; -Eis, Interconnect | 1 |
128-0830 Harness As-Power -Digital Voltage Regulator
| 12***30 | Harness As-Power; -Digital Voltage Regulator | 1 |
242-9752 Harness As-Power -Digital Voltage Regulator
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Terminal As-Ring | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
243-5280 Harness As-Sensor -Exhaust
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 8 |
| 15***22 | Seal; (70mm Od) | 1 |
243-5282 Harness As-Sensor -Exhaust
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 8 |
| 15***22 | Seal; (70mm Od) | 1 |
5n-9366 Harness As-Thermocouple
| 5N***66 | Harness As-Thermocouple; Lead Assembly-See Pyrometer Chart | 1 |
243-4271 Harness As-Wiring -Generator Terminal Strip
| 23***56 | Plug-Connector; (6-Pin) | 1 |
| 23***57 | Plug-Connector; (9-Pin) | 1 |
| 23***58 | Plug-Connector; (12-Pin) | 1 |
240-6834 Harness As-Wiring -Emcp Ii
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 10 |
| 24***34 | Harness As-Wiring; -Emcp Ii | 1 |
240-6833 Harness As-Wiring -Ignition, Lh
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
209-7551 Harness As-Wiring -Shunt Trip
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 2 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
166-8370 Harness As-Wiring -Governor
| 16***70 | Harness As-Wiring; -Governor | 1 |
242-3104 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 22 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
242-3100 Harness As-Wiring -Generator Terminal Strip
| 10***38 | End-Wire; (16-Ga) | 24 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***66 | Wedge-Plug Lock; (3-Pin) | 1 |
279-6642 Heater Gp-Jacket Water
| 27***42 | Heater Group-Jacket Water | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
7e-6247 Heater Gp-Jacket Water
| 12***60 | Thermostat As; (20-Deg C To 80-Deg C)(Jacket Water Heater) | 1 |
| 7E***47 | Heater Group-Jacket Water | 1 |
200-6504 Heater Gp-Jacket Water
| 10***32 | Thermostat; (60 Deg F To 160 Deg F)(Jacket Water Heater) | 1 |
| 20***04 | Heater Group-Jacket Water | 1 |
7e-6248 Heater Gp-Jacket Water
| 10***32 | Thermostat; (60 Deg F To 160 Deg F)(Jacket Water Heater) | 1 |
| 7E***48 | Heater Group-Jacket Water | 1 |
4p-8192 Ignition Gp-Gas Engine
| 03***43 | Screw; (1/4-20x0.625-In) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 1 |
147-2960 Ignition Gp-Gas Engine
| 03***43 | Screw; (1/4-20x0.625-In) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 1 |
320-9979 Installation Gp-Communication
| 22***59 | Cable As-Communication | 1 |
| 25***12 | Control Group-Communication; -Pl1000e | 1 |
| 27***85 | Harness As-Control; -Pl1000e | 1 |
320-9980 Installation Gp-Communication
| 25***11 | Control Group-Communication; -Pl1000t | 1 |
| 27***32 | Harness As-Control; -Pl1000t | 1 |
| 32***80 | Installation Group-Communication | 1 |
8n-8481 Lines Gp-Air Starting
| 11***84 | Lubricator Group-Air Motor | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 2L***11 | Nipple (L.H. Mounting) | 2 |
245-9933 Lines Gp-Air Starting
| 11***84 | Lubricator Group-Air Motor | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 24***33 | Lines Group-Air Starting | 1 |
119-6282 Lubricator Gp-Air Motor
| 11***82 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 6N***84 | Gasket | 1 |
| 6N***85 | Plug-Filler | 2 |
119-6284 Lubricator Gp-Air Motor
| 11***82 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 11***83 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
| 11***84 | Lubricator Group-Air Motor | 1 |
119-6283 Lubricator Gp-Air Motor
| 11***83 | Lubricator Group-Air Motor; Lubrication Gp-Air Motor | 1 |
270-4654 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 10 |
| 27***48 | Bracket | 1 |
106-7709 Mounting Gp-Circuit Breaker
| 10***17 | . Axle, Bracket As | 1 |
| 10***09 | Mounting Group-Circuit Breaker | 1 |
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
7c-2206 Mounting Gp-Circuit Breaker
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 5P***81 | Seal 1.334 M(53.50 In.) | 0 |
122-3488 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***88 | Mounting Group-Circuit Breaker | 1 |
| 12***29 | Bracket | 1 |
7c-0266 Mounting Gp-Circuit Breaker
| 3N***34 | Nut-Spring (3/8-16 Thd) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 5P***81 | Seal 1.334 M(53.50 In.) | 0 |
252-7525 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 25***21 | Support | 2 |
| 25***22 | Panel | 1 |
208-1195 Mounting Gp-Circuit Breaker
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 20***95 | Mounting Group-Circuit Breaker | 1 |
| 5S***03 | Nut-Full; (5/16 X 18 Thd) | 4 |
122-0319 Mounting Gp-Circuit Breaker
| 11***13 | Box Group-Extension Terminal; -Circuit Breaker | 1 |
| 12***93 | Bracket As-Circuit Breaker; -Circuit Breaker | 1 |
| 12***19 | Mounting Group-Circuit Breaker | 1 |
6i-1040 Mounting Gp-Jacket Wtr Heater -Rh
| 03***28 | Clip; (31.8mm Id) | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 1K***37 | Elbow-Pipe | 1 |
6i-1039 Mounting Gp-Jacket Wtr Heater -Lh
| 00***35 | Elbow-External Pipe Thread | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
199-2710 Mounting Gp-Terminal Strip
| 19***58 | Block Group-Junction | 1 |
| 19***10 | Mounting Group-Terminal Strip | 1 |
4p-2454 Mounting Gp-Transformer
| 12***74 | Clip-Loop; (12.7mm Id) | 1 |
| 4P***54 | Mounting Group-Transformer | 1 |
| 6K***06 | Strap-Cable -Lines From Rotate Valve | 3 |
141-1810 Mounting Gp-Transformer
| 14***10 | Mounting Group-Transformer | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 4 |
106-7696 Panel As-Box -Circuit Breaker
| 10***18 | Panel-Circuit Breaker | 1 |
| 10***96 | Panel As-Box; -Circuit Breaker | 1 |
| 7W***91 | Seal (104 cm) | 0 |
9y-8441 Panel As-Box
| 7W***91 | Seal (104 cm) | 0 |
| 9Y***40 | Panel-Box | 1 |
| 9Y***41 | Panel As-Box | 1 |
122-0317 Panel As-Box -Circuit Breaker
| 12***17 | Panel As-Box; -Circuit Breaker | 1 |
| 12***40 | Panel-Circuit Breaker | 1 |
| 7W***91 | Seal (104 cm) | 0 |
252-7535 Panel Gp-Circuit Breaker -Cover
| 10***45 | Bolt-Flange Head; (5/16-18x0.625-In) | 12 |
| 25***23 | Panel | 1 |
| 25***35 | Panel Group-Circuit Breaker; -Cover | 1 |
138-3809 Relay As -Power
| 13***09 | Relay As; (Heater Control)(24 Vdc Pump Energize) | 1 |
134-1157 Relay Gp -Engine Failure
| 12***26 | Relay Group; -Auxiliary | 1 |
| 13***57 | Relay Group; -Engine Failure | 1 |
| 15***81 | Relay Group; -Engine Failure | 1 |
158-6181 Relay Gp
| 15***81 | Relay Group; -Engine Failure | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
122-0335 Relay Gp -Space Heater
| 11***47 | Relay; (2-Pole) | 1 |
| 12***35 | Relay Group; -Space Heater | 1 |
| 12***92 | Base-Relay | 1 |
128-3326 Relay Gp -Auxiliary
| 12***26 | Relay Group; -Auxiliary | 1 |
| 21***40 | Spring; (Relay)(Us Sourced) | 1 |
| 22***70 | Relay; (10-Ampere, 24-Volt)(Us Sourced) | 1 |
221-0752 Relay Gp -Space Heater
| 10***38 | End-Wire; (16-Ga) | 4 |
| 12***99 | Harness As-Wiring; (Main Terminal Strip) | 1 |
| 12***97 | Harness As-Wiring; (Dc Terminal Strip) | 1 |
105-2048 Sensor & Mtg Gp-Radiator
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***48 | Sensor & Mtg Group-Radiator | 1 |
| 11***52 | Harness As-Sensor; (Coolant Level) | 1 |
121-3354 Sensor & Mtg Gp-Radiator
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***54 | Sensor & Mtg Group-Radiator; -Coolant | 1 |
| 12***55 | Harness As-Sensor; (Coolant Level) | 1 |
165-6634 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***34 | Sensor Group-Coolant Level; (Water, Coolant)(Scac Expansion Tank) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
111-3794 Sensor Gp-Coolant Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***94 | Sensor Group-Coolant Level; -Coolant Loss-Aftercooler, Jacket Water | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
143-8540 Sensor Gp-Coolant Level
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 14***40 | Sensor Group-Coolant Level | 1 |
| 14***61 | Harness As-Switch; (Coolant Level) | 1 |
9w-5565 Sensor Gp-Temp & Press
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
| 7N***38 | Housing-Receptacle-Sure Seal-Assemble | 1 |
204-2518 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 20***18 | Sensor Group-Liquid Level; (Jacket Water) | 1 |
228-9852 Sensor Gp-Pressure
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 1 |
| 22***52 | Sensor Group-Pressure | 1 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
127-2018 Sensor Gp-Pressure
| 12***18 | Sensor Group-Pressure | 1 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
| 9X***13 | Sleeve (Order By cm)(Use As Required) | 0 |
216-8684 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***39 | Pin-Connector; (14-Ga To 18-Ga)(For 14 Gauge Wire) | 3 |
| 21***84 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
3e-1854 Sensor Gp-Pressure
| 3E***54 | Sensor Group-Pressure | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
163-8516 Sensor Gp-Pressure
| 16***16 | Sensor Group-Pressure; -Boost And Engine Oil | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 1 |
| 19***27 | Harness As-Sensor; (14-Ga Wire)(Engine Oil Temperature) | 1 |
145-2362 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 14***62 | Sensor Group-Pressure; -Torque Converter Oil | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
265-9034 Sensor Gp-Speed
| 11***66 | Seal-O-Ring | 1 |
| 13***07 | Washer; (21.1x28.1x0.9-mm Thk) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
8l-4171 Sensor Gp-Speed
| 8L***71 | Sensor Group-Speed; -Low Output | 1 |
7w-3355 Sensor Gp-Speed
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 4B***81 | Washer--Use With Customer'S Ground Bolt | 1 |
| 7W***55 | Sensor Group-Speed; -Engine Timing | 1 |
102-9029 Sensor Gp-Speed
| 10***29 | Sensor Group-Speed; -Timing-Engine Speed | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 3 |
| 8L***86 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
189-5746 Sensor Gp-Speed -Output
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***36 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 17***49 | Strap; (Marker) | 1 |
9x-5392 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
3e-7886 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
175-5341 Sensor Gp-Temperature
| 17***41 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 8T***32 | Receptacle-Connector; (3-Pin)(Throttle Position Sensor) | 1 |
6i-4908 Sensor Gp-Temperature -Generator Bearing
| 11***52 | Strip-Terminal | 1 |
| 11***21 | Lead As-Sensor | 1 |
| 11***72 | Sender As-Temperature; (100-Ohm) | 2 |
180-5420 Sensor Gp-Temperature
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 18***20 | Sensor Group-Temperature | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
6i-4906 Sensor Gp-Temperature -Generator Bearing
| 11***22 | Sender As-Temperature; (100-Ohm)(Generator Bearing) | 1 |
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
141-4159 Sensor Gp-Temperature -Generator Bearing
| 14***59 | Sensor Group-Temperature; -Generator Bearing | 1 |
141-4160 Sensor Gp-Temperature -Generator Bearing
| 14***60 | Sensor Group-Temperature; -Generator Bearing | 1 |
6i-4907 Sensor Gp-Temperature -Generator Bearing
| 11***99 | Strip-Terminal | 1 |
| 11***46 | Strip-Terminal | 1 |
| 11***47 | Cover | 1 |
141-4161 Sensor Gp-Temperature -Generator Bearing
| 14***61 | Sensor Group-Temperature; -Generator Bearing | 1 |
241-9591 Sensor Gp-Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 24***91 | Sensor Group-Temperature | 1 |
141-4158 Sensor Gp-Temperature -Generator Bearing
| 14***58 | Sensor Group-Temperature; -Generator Bearing | 1 |
102-0050 Sensor Gp-Temperature
| 10***50 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
6i-4909 Sensor Gp-Temperature -Generator Bearing
| 11***52 | Strip-Terminal | 1 |
| 11***21 | Lead As-Sensor | 1 |
| 11***73 | Sender As-Temperature; (10-Ohm)(Generator Bearing) | 2 |
167-5103 Shutoff Gp-Electrical
| 10***50 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 12***18 | Sensor Group-Pressure | 1 |
| 16***03 | Shutoff Group-Electrical | 1 |
108-6424 Shutoff Gp-Electrical
| 10***24 | Shutoff Group-Electrical | 1 |
| 10***71 | Control Group-Engine Monitoring | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
8n-8486 Silencer Gp-Air Starting
| 1D***66 | Bolt Bracket Assembly To Yoke | 2 |
| 1D***69 | Bolt 107.95 mm(4.25 In.) Long; Bolt (Plate To Front Housing) | 2 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
112-6597 Silencer Gp-Air Starting
| 10***69 | Silencer-Air Starting | 1 |
| 11***97 | Silencer Group-Air Starting | 1 |
| 14***96 | Bolt-Socket Head; (1/2-13x1.25-In) | 2 |
7c-0527 Starting Motor Gp-Electric -Dual
| 3L***04 | Shield-Terminal | 4 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 2 |
237-1962 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 13 |
8n-3896 Starting Motor Gp-Electric -Dual
| 3L***36 | Spacer-Bracket To Diesel Water Passage Cover | 1 |
| 3L***04 | Shield-Terminal | 4 |
| 3L***34 | Terminal-Ring; (0000-Ga, 1/2-In Screw) | 2 |
106-8554 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
7c-0526 Starting Motor Gp-Electric -Single
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
| 6V***46 | Starting Motor Group-Electric | 1 |
| 7C***26 | Starting Motor Group-Electric; -Single | 1 |
6v-0927 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
6v-4246 Starting Motor Gp-Electric
| 10***51 | Starting Motor Group-Electric; Motor Gp-Electric Hydraulic Pump | 1 |
| 6V***46 | Starting Motor Group-Electric | 1 |
| 6V***20 | Starting Motor Group-Electric | 1 |
6v-5582 Starting Motor Gp-Electric
| 3E***25 | Cover As; (Starting Motor) | 1 |
| 3E***27 | Kit-Bearing; (Starting Motor)(Incl Bearing Seals & Spacers) | 1 |
| 3E***28 | Kit; (Brush) (Includes O-Rings, Screw, Spring, & Brush) | 1 |
207-1562 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 20***62 | Starting Motor Group-Electric | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
6v-4320 Starting Motor Gp-Electric
| 5C***74 | Nut (M5x.8 Thd); (M5x0.8-Thd) | 2 |
| 6V***20 | Starting Motor Group-Electric | 1 |
| 7X***62 | Washer-Hard; (13.5x19x0.8-mm Thk) | 5 |
6v-5539 Starting Motor Gp-Electric
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
| 6V***39 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 6V***82 | Starting Motor Group-Electric; (Nippondenso) | 1 |
207-1556 Starting Motor Gp-Electric
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 5 |
| 20***56 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
106-8551 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***51 | Starting Motor Group-Electric; Motor Gp-Electric Hydraulic Pump | 1 |
170-5397 Strip Gp-Terminal -Ac
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 5 |
170-5399 Strip Gp-Terminal -Dc
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***06 | Bar | 1 |
| 17***99 | Strip Group-Terminal; -Dc | 1 |
170-5396 Strip Gp-Terminal -Rtd
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 17***96 | Strip Group-Terminal; -Rtd | 1 |
| 31***98 | Block-Terminal; (600-Volt, 25-Ampere) | 34 |
170-5395 Strip Gp-Terminal -Thermocouple
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 16***89 | Bracket-End | 2 |
| 16***17 | Cover-Terminal | 7 |
170-5400 Strip Gp-Terminal -Main
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 15***55 | Fuse; (10-Ampere) | 2 |
| 17***00 | Strip Group-Terminal; -Main | 1 |
126-6830 Strip Gp-Terminal
| 11***40 | Strip As; (Emcp Ii Ac) | 1 |
| 11***41 | Strip As; (Emcp Ii Dc) | 1 |
| 12***97 | Bracket As | 1 |
3n-7056 Support Gp-Battery
| 3N***54 | Support As-Battery | 1 |
| 3N***55 | Board | 1 |
| 3N***56 | Support Group-Battery | 1 |
132-0118 Suppressor Gp-Electronic
| 13***18 | Suppressor Group-Electronic | 1 |
143-7886 Switch As -Circuit Breaker Position, Fault Indicator
| 14***86 | Switch As; -Circuit Breaker Position, Fault Indicator | 1 |
105-7931 Switch As-Auxiliary
| 10***31 | Switch As-Auxiliary; -Circuit Breaker | 1 |
105-7932 Switch As-Auxiliary
| 10***32 | Switch As-Auxiliary | 1 |
158-4240 Switch As-Selector
| 15***40 | Switch As-Selector | 1 |
4w-4755 Switch Gp-Magnetic
| 3B***01 | Lockwasher (Part Of 3f***99 Switch) | 2 |
| 3F***56 | Lockwasher; (8.43x15.5x0.76mm Thk) | 2 |
| 4B***47 | Nut,Plain,Square Circuit Breaker Uoc:Bsv,Bsx | 2 |
119-0801 Switch Gp-Magnetic
| 11***01 | Switch Group-Magnetic | 1 |
| 3B***01 | Lockwasher (Part Of 3f***99 Switch) | 2 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 2 |
119-0800 Switch Gp-Magnetic
| 11***00 | Switch Group-Magnetic | 1 |
| 3B***02 | Washer,Lock Circuit Breaker Uoc:Bsv,Bsx | 2 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 2 |
3e-0075 Switch Gp-Magnetic
| 17***22 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 3E***75 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
175-2324 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
175-2322 Switch Gp-Magnetic
6i-1230 Switch Gp-Magnetic
| 3E***75 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 3E***61 | Plug As-Connector; (2-Pin) | 1 |
| 3E***62 | Wedge-Plug Lock; (2-Pin) | 1 |
169-5384 Switch Gp-Remote -Starting
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 4 |
| 16***84 | Switch Group-Remote; -Starting | 1 |
| 16***85 | Bracket-Switch | 1 |
134-8620 Switch Gp-Start
| 11***54 | Circuit Breaker As; (20-Ampere) | 1 |
| 11***00 | Switch Group-Magnetic | 1 |
| 13***20 | Switch Group-Start | 1 |
134-8621 Switch Gp-Start
| 11***54 | Circuit Breaker As; (20-Ampere) | 1 |
| 11***00 | Switch Group-Magnetic | 1 |
| 11***01 | Switch Group-Magnetic | 1 |
3e-0264 Switch Gp-Temperature
| 3E***64 | Switch Group-Temperature; -Coolant | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
244-9850 Terminal-Circuit Breaker
| 24***50 | Terminal-Circuit Breaker | 1 |
5n-9365 Thermocouple
| 5N***65 | Thermocouple | 1 |
7c-0182 Thermocouple Gp
| 3N***78 | Adapter-Sensor; Adapter--1/2" Pipe Thread | 2 |
| 5N***65 | Thermocouple | 2 |
| 5N***66 | Harness As-Thermocouple; Lead Assembly-See Pyrometer Chart | 2 |
130-8239 Transformer As
| 13***39 | Transformer As | 1 |
130-8240 Transformer As
| 13***40 | Transformer As | 1 |
244-4462 Transformer As -Current
| 24***62 | Transformer As; -Current | 1 |
243-3129 Transformer As
| 24***29 | Transformer As | 1 |
| 24***06 | Transformer | 2 |
| 7E***63 | Strip-Terminal | 1 |
117-9722 Transformer As-Current
| 11***22 | Transformer As-Current | 1 |
204-3544 Transformer As-Current
| 20***44 | Transformer As-Current | 1 |
128-0116 Transformer As-Current
| 12***16 | Transformer As-Current | 1 |
122-6590 Transformer As-Current
| 12***90 | Transformer As-Current; (3000:5 Ratio)(3000:5) | 1 |
122-6585 Transformer As-Current
| 12***85 | Transformer As-Current | 1 |
117-9721 Transformer As-Current
| 11***21 | Transformer As-Current | 1 |
122-6591 Transformer As-Current
| 12***91 | Transformer As-Current | 1 |
119-0976 Transformer As-Current
| 11***76 | Transformer As-Current | 1 |
122-6586 Transformer As-Current
| 12***86 | Transformer As-Current | 1 |
128-0795 Transformer As-Current
| 12***95 | Transformer As-Current | 1 |
117-9724 Transformer As-Current
| 11***24 | Transformer As-Current | 1 |
122-6587 Transformer As-Current
| 12***87 | Transformer As-Current | 1 |
128-0115 Transformer As-Current
| 12***15 | Transformer As-Current | 1 |
119-0977 Transformer As-Current
| 11***77 | Transformer As-Current | 1 |
122-6589 Transformer As-Current
| 12***89 | Transformer As-Current | 1 |
137-0259 Transformer As-Current
| 13***59 | Transformer As-Current | 1 |
117-9723 Transformer As-Current
| 11***23 | Transformer As-Current | 1 |
122-6588 Transformer As-Current
| 12***88 | Transformer As-Current | 1 |
206-0253 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 13***59 | Transformer As-Current | 3 |
| 20***53 | Transformer Group-Current | 1 |
144-9059 Transformer Gp-Current
| 12***89 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***59 | Transformer Group-Current | 1 |
206-0245 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***91 | Transformer As-Current | 3 |
| 20***45 | Transformer Group-Current | 1 |
206-0252 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***95 | Transformer As-Current | 3 |
| 20***52 | Transformer Group-Current | 1 |
206-0247 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***21 | Transformer As-Current | 3 |
| 20***47 | Transformer Group-Current | 1 |
144-9063 Transformer Gp-Current
| 11***21 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***63 | Transformer Group-Current | 1 |
206-0241 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***87 | Transformer As-Current | 3 |
| 20***41 | Transformer Group-Current | 1 |
206-0244 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***90 | Transformer As-Current; (3000:5 Ratio)(3000:5) | 3 |
| 20***44 | Transformer Group-Current | 1 |
206-0240 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***24 | Transformer As-Current | 3 |
| 20***40 | Transformer Group-Current | 1 |
206-0242 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***88 | Transformer As-Current | 3 |
| 20***42 | Transformer Group-Current | 1 |
206-0248 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***22 | Transformer As-Current | 3 |
| 20***48 | Transformer Group-Current | 1 |
206-0250 Transformer Gp-Current
144-9058 Transformer Gp-Current
| 12***88 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***58 | Transformer Group-Current | 1 |
206-0246 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***15 | Transformer As-Current | 3 |
| 20***46 | Transformer Group-Current | 1 |
206-0243 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***89 | Transformer As-Current | 3 |
| 20***43 | Transformer Group-Current | 1 |
144-9065 Transformer Gp-Current
| 11***23 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***65 | Transformer Group-Current; -Droop | 1 |
144-9064 Transformer Gp-Current
| 11***22 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***64 | Transformer Group-Current | 1 |
229-5837 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***85 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
206-0251 Transformer Gp-Current
144-9057 Transformer Gp-Current
| 12***87 | Transformer As-Current | 1 |
| 14***10 | Mounting Group-Transformer | 1 |
| 14***57 | Transformer Group-Current | 1 |
206-0249 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 11***23 | Transformer As-Current | 3 |
| 20***49 | Transformer Group-Current | 1 |
229-5838 Transformer Gp-Current
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***86 | Transformer As-Current | 3 |
| 20***79 | Harness As-Wiring; (Current Transformer) | 1 |
232-6346 Transformer Gp-Ignition
| 12***72 | Seal-O-Ring | 1 |
| 12***38 | Spring-Transformer | 1 |
| 13***51 | Seal; (Pressure Relief) | 1 |
135-8211 Transformer Gp-Potential
| 12***46 | Resistor | 1 |
| 13***22 | Bracket-Transformer | 1 |
| 13***11 | Transformer Group-Potential | 1 |
178-7191 Transformer Gp-Potential
| 15***70 | Shelf; (Transformer) | 1 |
| 17***91 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 3 |
178-7193 Transformer Gp-Potential
| 15***71 | Shelf; (Transformer) | 1 |
| 17***93 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 3 |
154-3475 Transformer Gp-Potential
| 14***03 | Transformer As; (Potential) | 2 |
| 15***70 | Shelf; (Transformer) | 1 |
| 15***75 | Transformer Group-Potential | 1 |
154-3454 Transformer Gp-Potential
| 15***70 | Shelf; (Transformer) | 1 |
| 15***54 | Transformer Group-Potential | 1 |
| 15***88 | Transformer As; (Low Voltage) | 2 |
243-3205 Transformer Gp-Potential
| 24***29 | Transformer As | 1 |
| 24***05 | Transformer Group-Potential | 1 |
| 6V***89 | Nut-Full (5/16 X 18 Thd) | 4 |
175-7748 Transformer Gp-Potential
| 17***48 | Transformer Group-Potential | 1 |
| 20***18 | Transformer As; (Potential) | 1 |
119-0978 Transformer-Current
| 11***78 | Transformer-Current; (Ratio 800:5) | 1 |
5n-8980 Valve As-Solenoid -Air Start
| 3F***65 | Locknut; (1/2-14-Nptf-Thd) | 1 |
| 5N***43 | Adapter (Small); (.50-14 Thd) | 1 |
| 5N***80 | Valve As; -Air Start | 1 |
1l-2073 Valve Gp-Pressure Reducing -Rh
| 0T***20 | Bolt (1.25 In. Long X .438 In. Dia.) | 1 |
| 1H***69 | Button-Spring | 1 |
| 1H***70 | Chamber | 1 |
130-5177 Valve Gp-Solenoid -Air Start
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***31 | Valve Group-Solenoid; (Air Start) | 1 |
| 13***77 | Valve Group-Solenoid; -Air Start-Air Starting | 1 |
9y-6061 Valve Gp-Solenoid -Gas Shutoff
| 3B***96 | Fitting; (Nipple) | 1 |
| 7X***51 | Elbow-Union | 1 |
| 9Y***61 | Valve Group-Solenoid; -Gas Shutoff | 1 |
4p-9596 Valve Gp-Solenoid -Gas Shutoff
| 13***22 | Harness As-Solenoid; (Fuel Shutoff) | 1 |
| 3B***00 | Elbow | 2 |
| 3B***96 | Fitting; (Nipple) | 4 |
9y-6992 Valve Gp-Solenoid -Gas Shutoff
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 4P***77 | Gasket | 1 |
| 9X***06 | Receptacle As | 1 |
103-0692 Valve Gp-Solenoid -Gas Shutoff
| 10***92 | Valve Group-Solenoid; -Gas Shutoff | 1 |
| 7X***78 | Coil As | 1 |
7c-0301 Harness As-Panel -Circuit Breaker
| 3P***54 | Grommet | 1 |
| 3S***88 | Dispenser Group-Marker Tape; (Numbers 0ne To One Thousand)(No 1 To 1000) | 1 |
| 5P***76 | Terminal-Fork; (14-Ga To 16-Ga, No. 10 Screw)(14-16 Gauge-No. 10 Screw) | 2 |
106-5670 Harness As-Panel -Circuit Breaker
| 10***70 | Wiring Group; -Circuit Breaker | 1 |
| 10***71 | Marker-Wire | 1 |
| 5N***61 | Conduit-Flexible; (12.7mm .50in Id) | 20 |
327-8608 Wiring Gp-Alternator
| 12***87 | Mount-Flexible | 1 |
| 32***08 | Wiring Group-Alternator | 1 |
| 32***09 | Harness As-Power | 1 |
327-8606 Wiring Gp-Alternator
| 12***87 | Mount-Flexible | 1 |
| 32***06 | Wiring Group-Alternator | 1 |
| 32***07 | Harness As-Power | 1 |
113-3382 Wiring Gp-Eis
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 15 |
| 11***82 | Wiring Group-Eis | 1 |
| 11***18 | Clip | 8 |
154-3868 Wiring Gp-Eis
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 15***68 | Wiring Group-Eis | 1 |
| 15***69 | Harness As-Wiring; (Governor Actuator) | 1 |
4p-9895 Wiring Gp-Eis
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 1 |
| 10***25 | Name-Plate (Lubrication), Mounting Group-Instrument Panel | 1 |
226-4165 Wiring Gp-Eis -Rh
| 22***65 | Wiring Group-Eis; -Rh | 1 |
| 4P***28 | Clip; (13.5mm Id) | 2 |
| 4P***81 | Clip (For Use With 7.9mm Wide Tie Wrap) | 6 |
145-5138 Wiring Gp-Electronic Control
| 12***30 | Harness As-Power; -Digital Voltage Regulator | 1 |
| 14***38 | Wiring Group-Electronic Control | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 5 |
129-5684 Wiring Gp-Engine -Eis
| 03***42 | Resistor | 1 |
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 11***43 | Circuit Breaker As; (16-Ampere) | 1 |
154-3865 Wiring Gp-Engine
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 11***18 | Clip | 1 |
| 13***58 | Cable-Electrical; (16-Ga)(3089-cm) | 0 |
154-3851 Wiring Gp-Engine -Electric Start
| 14***63 | Plug As-Connecting | 1 |
| 15***51 | Wiring Group-Engine; -Electric Start | 1 |
| 15***52 | Harness As-Wiring; (Electric Start) | 1 |
166-8368 Wiring Gp-Generator
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 32 |
| 10***39 | End-Wire; (12-Ga) | 8 |
242-7960 Wiring Gp-Generator
| 24***00 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***60 | Wiring Group-Generator | 1 |
261-7168 Wiring Gp-Generator
| 10***71 | Marker-Wire | 1 |
| 10***38 | End-Wire; (16-Ga) | 4 |
| 26***67 | Harness As-Wiring; (Shunt Trip) | 1 |
166-8364 Wiring Gp-Generator
| 16***64 | Wiring Group-Generator | 1 |
| 16***65 | Harness As-Wiring; (Engine Sensors) | 1 |
| 16***66 | Harness As-Wiring; (Governor Controls) | 1 |
241-3379 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 10 |
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 24***68 | Harness As-Wiring; (Voltage Adjustment) | 1 |
243-4285 Wiring Gp-Generator
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 24***71 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***85 | Wiring Group-Generator | 1 |
122-0320 Wiring Gp-Generator -Shunt Trip
| 12***20 | Wiring Group-Generator; -Shunt Trip | 1 |
| 20***51 | Harness As-Wiring; -Shunt Trip | 1 |
| 7K***81 | Strap-Pressure & Return Hoses To | 10 |
243-4269 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 9 |
| 24***69 | Wiring Group-Generator | 1 |
| 24***01 | Harness As-Wiring; (Vr6 Voltage Regulator) | 1 |
241-3378 Wiring Gp-Generator
| 10***38 | End-Wire; (16-Ga) | 3 |
| 11***84 | Switch As-Toggle; (Momentary)(Manual Engine Speed Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
166-8367 Wiring Gp-Generator -Starting Motor
| 16***67 | Wiring Group-Generator; -Starting Motor | 1 |
| 16***71 | Harness As-Wiring; (Starting Controls) | 1 |
| 16***84 | Switch Group-Remote; -Starting | 1 |
242-7961 Wiring Gp-Generator
| 24***04 | Harness As-Wiring; -Generator Terminal Strip | 1 |
| 24***61 | Wiring Group-Generator | 1 |
| 24***52 | Harness As-Power; -Digital Voltage Regulator | 1 |
109-4691 Wiring Gp-Instr & Ignition
| 10***87 | Harness As-Engine | 1 |
| 10***91 | Wiring Group-Instr & Ignition | 1 |
| 1L***61 | Plug (Use Without Ammeter); (Mtd. On Instr. Panel) | 1 |
198-5460 Wiring Gp-Panel -Low Voltage
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***38 | End-Wire; (16-Ga) | 6 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
248-4905 Wiring Gp-Panel -Vr6 Voltage Regulator
| 10***38 | End-Wire; (16-Ga) | 12 |
| 12***70 | Potentiometer; (10,000-Ohm)(Voltage Adjustment) | 1 |
| 24***68 | Harness As-Wiring; (Voltage Adjustment) | 1 |
192-4137 Wiring Gp-Pyrometer
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 15***77 | Washer; (4.445x9.525x1.092-mm Thk) | 4 |
| 16***89 | Plug As-Connector; (70-Pin)(50x80.9mm) | 1 |
192-4134 Wiring Gp-Pyrometer
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 15***77 | Washer; (4.445x9.525x1.092-mm Thk) | 4 |
| 17***41 | Sensor Group-Temperature | 16 |
147-8181 Wiring Gp-Sensor
| 09***26 | Splice | 7 |
| 09***04 | Tube-Heat Shrink; (19.1-mm Dia)(6-cm) | 0 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 7 |
176-5866 Wiring Gp-Sensor
| 13***58 | Cable-Electrical; (16-Ga)(3089-cm) | 0 |
| 17***66 | Wiring Group-Sensor | 1 |
| 17***69 | Harness As-Sensor | 1 |
Enclosures, Guards And Bases
324-4579 Bracket Gp-Support
| 18***14 | Bracket-Support | 2 |
| 18***15 | Plate | 1 |
| 32***79 | Bracket Group-Support | 1 |
141-4987 Cover Gp-Generator -Coupling
| 12***94 | Cover-Drip | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 1D***40 | Bolt,Machine Fuel Filter Mounting | 6 |
128-6149 Cover Gp-Generator -Front
| 12***49 | Cover Group-Generator; -Front | 1 |
| 4F***11 | Plug 3.5 cm(1.37 In.) Hole; Plug-- To Support Assembly | 2 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 8 |
115-2508 Cover Gp-Generator -Top
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 11***08 | Cover Group-Generator; -Top | 1 |
| 5N***67 | Seal; 1.52mm(.059in)Thk | 3 |
131-0539 Cover Gp-Generator -Coupling
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 12***99 | Bracket-Mounting | 2 |
| 13***38 | Cover-Drip | 1 |
4p-9064 Guard Gp-Extension
| 1V***23 | Plate | 4 |
| 2N***85 | Nut-Clip-Damper Guard To Coupling Guard | 8 |
| 4P***63 | Guard As-Extension | 1 |
3n-5764 Guard Gp-Extension
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 16 |
| 1V***23 | Plate | 8 |
| 2N***85 | Nut-Clip-Damper Guard To Coupling Guard | 16 |
160-9800 Pad-Isolator
| 16***00 | Pad-Isolator | 1 |
122-4869 Panel As-Enclosure -Extension Box
| 12***69 | Panel As-Enclosure; -Extension Box | 1 |
195-8037 Rail Gp-Engine Support
| 18***11 | Brace-Engine Support | 2 |
| 19***37 | Rail Group-Engine Support | 1 |
| 19***38 | Support-Rh | 1 |
197-5508 Rail Gp-Engine Support
| 18***11 | Brace-Engine Support | 1 |
| 18***14 | Bracket-Support | 3 |
| 18***15 | Plate | 1 |
7w-3749 Rail Gp-Engine Support
| 1A***58 | Bolt 1.75 In. (44.45 mm) Long | 36 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 36 |
| 7W***49 | Rail Group-Engine Support | 1 |
197-5512 Rail Gp-Engine Support
| 18***11 | Brace-Engine Support | 1 |
| 18***14 | Bracket-Support | 2 |
| 18***15 | Plate | 1 |
9y-0845 Rail Gp-Engine Support
| 8T***94 | Washer; (3/4 Hardened) (Current Adapters) | 28 |
| 8T***98 | Capscrew; (Hex Hd) (3/4-10x1 3/4 Gd 8 Z) (Early Adapters) | 28 |
| 9Y***45 | Rail Group-Engine Support | 1 |
Engine Arrangement
199-2615 Engine Ar
| 10***86 | Actuator Group-Governor | 1 |
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
| 11***03 | Camshaft Group | 1 |
295-1389 Engine Ar
| 10***56 | Piston & Rod Group | 8 |
| 10***47 | Regulator Group-Gas Pressure | 1 |
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
199-2611 Engine Ar
| 10***47 | Regulator Group-Gas Pressure | 1 |
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
| 11***03 | Camshaft Group | 1 |
273-3097 Engine Ar
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
| 11***03 | Camshaft Group | 1 |
| 11***02 | Cylinder Block Group | 1 |
199-2614 Engine Ar
| 10***56 | Piston & Rod Group | 8 |
| 10***47 | Regulator Group-Gas Pressure | 1 |
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
196-2219 Engine Ar
| 11***77 | Gear Group-Rear; -Cam Drive | 1 |
| 11***03 | Camshaft Group | 1 |
| 11***02 | Cylinder Block Group | 1 |
199-2645 General Ar
| 19***14 | Engine Ar | 1 |
| 19***45 | General Ar | 1 |
196-2130 General Ar
| 19***30 | General Ar | 1 |
| 19***19 | Engine Ar | 1 |
291-6049 General Ar
| 27***97 | Engine Ar | 1 |
| 29***49 | General Ar | 1 |
196-2131 General Ar
| 19***31 | General Ar | 1 |
| 19***11 | Engine Ar | 1 |
291-6050 General Ar
| 29***50 | General Ar | 1 |
| 29***89 | Engine Ar | 1 |
199-2646 General Ar
| 19***15 | Engine Ar | 1 |
| 19***46 | General Ar | 1 |
8n-7151 Installation Ar
| 1A***22 | Bolt-Generator To Flywheel Housing | 16 |
| 1B***33 | Nut--Generator To Support Assembly | 4 |
| 1D***37 | Bolt-Generator To Support Assembly | 6 |
Fuel System
118-7590 Actuator As
| 11***90 | Actuator As | 1 |
108-4886 Actuator Gp-Governor
| 10***86 | Actuator Group-Governor | 1 |
| 10***55 | Conduit As | 1 |
| 11***90 | Actuator As | 1 |
154-3867 Actuator Gp-Governor
| 10***55 | Conduit As | 1 |
| 11***90 | Actuator As | 1 |
| 15***67 | Actuator Group-Governor | 1 |
1w-8887 Actuator Gp-Governor
| 14***43 | Governor Group | 1 |
| 1W***35 | Drive Group-Governor; Governor Drive Group | 1 |
| 1W***87 | Actuator Group-Governor | 1 |
178-4530 Actuator Gp-Governor
| 17***29 | Actuator Group-Governor | 1 |
| 17***30 | Actuator Group-Governor | 1 |
| 4P***51 | Control Group-Carburetor | 1 |
178-4529 Actuator Gp-Governor
| 10***55 | Conduit As | 1 |
| 11***90 | Actuator As | 1 |
| 17***29 | Actuator Group-Governor | 1 |
7e-1593 Body As-Carburetor
| 03***13 | Seal-O-Ring | 1 |
| 3F***74 | Nut-Self Locking; (1/4-28 Thd) | 1 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 1 |
106-6497 Carburetor Gp
| 10***97 | Carburetor Group | 1 |
| 10***04 | Gasket | 1 |
| 10***07 | Flange | 1 |
211-1688 Carburetor Gp
| 10***10 | Insert-Carburetor | 2 |
| 21***88 | Carburetor Group | 1 |
106-7948 Carburetor Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 10***97 | Carburetor Group | 2 |
| 10***10 | Insert-Carburetor | 2 |
2w-1469 Carburetor Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 2W***69 | Carburetor Group | 1 |
| 4B***88 | Bolt (5/16 X 28.58 mm); (5/16-18x1.125-In) | 1 |
7e-8282 Carburetor Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 10***97 | Carburetor Group | 2 |
| 5P***60 | Clamp-Hose | 4 |
7e-4064 Carburetor Gp
| 09***24 | Screw As; (12-24x0.625-In) | 6 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
131-5457 Control As-Governor -Speed Control
| 13***57 | Control As-Governor; -Speed Control | 1 |
131-5451 Control As-Governor -Speed Control
| 13***51 | Control As-Governor; -Speed Control | 1 |
293-8356 Control As-Governor -Load Share Module
| 29***56 | Control As-Governor; -Load Share Module | 1 |
131-5452 Control As-Governor -Speed Control
| 13***52 | Control As-Governor; -Speed Control | 1 |
4p-6940 Control Gp-Carburetor
| 11***69 | Sleeve | 6 |
| 12***79 | Rod | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 8 |
4p-6741 Control Gp-Carburetor
| 11***69 | Sleeve | 8 |
| 11***92 | Rod | 1 |
| 12***79 | Rod | 1 |
4p-5251 Control Gp-Carburetor
| 11***69 | Sleeve | 3 |
| 11***92 | Rod | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 7 |
9y-5896 Drive Gp-Governor
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 2 |
| 1A***60 | Capscrew, Hex Head (1/2 - 13 X 2 G5); (Hex Head) (1/2-13x2 Gd 8 Z) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
1w-2135 Drive Gp-Governor
| 06***57 | Seal-O-Ring | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 5 |
4w-5267 Drive Gp-Tachometer
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 8 |
4p-4717 Filter Gp-Fuel
| 4P***17 | Filter Group-Fuel | 1 |
| 4P***20 | Filter Element-Fuel; (Gas) | 1 |
321-6971 Filter Gp-Fuel
| 09***13 | Plug-Pipe | 1 |
| 32***71 | Filter Group-Fuel | 1 |
| 32***85 | Filter Element Group-Fuel; (Gas) | 1 |
321-6970 Filter Gp-Fuel
| 09***13 | Plug-Pipe | 1 |
| 32***70 | Filter Group-Fuel | 1 |
| 32***84 | Filter Element Group-Fuel; (Gas) | 1 |
143-6143 Governor Gp
| 14***43 | Governor Group | 1 |
| 17***86 | Breather; (Governor) | 1 |
| 1W***80 | Gasket | 1 |
107-4471 Governor Gp-Electric
| 10***71 | Governor Group-Electric | 1 |
| 11***90 | Actuator As | 1 |
| 4B***81 | Washer--Use With Customer'S Ground Bolt | 1 |
166-9270 Governor Gp-Electronic
| 12***68 | Potentiometer; (100-Ohm, 2-Watt)(Engine Speed) | 1 |
| 13***51 | Control As-Governor; -Speed Control | 1 |
| 16***70 | Governor Group-Electronic | 1 |
132-5543 Lines Gp-Gas
| 00***81 | Tee-Union; (Flared 37-Deg) | 1 |
| 03***72 | Elbow; (Flared 90 Degree) | 3 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 1 |
7e-3407 Regulator As-Gas Pressure
| 12***52 | Plate-Diaphragm | 2 |
| 12***53 | Case-Diaphragm | 1 |
| 12***54 | Case-Diaphragm | 1 |
335-5764 Regulator As-Gas Pressure
| 12***52 | Plate-Diaphragm | 2 |
| 12***53 | Case-Diaphragm | 1 |
| 12***54 | Case-Diaphragm | 1 |
100-8227 Regulator Gp-Gas Pressure
| 10***27 | Regulator Group-Gas Pressure | 1 |
| 13***84 | Body-Valve; (Gas Pressure Regulator) | 1 |
| 13***86 | Seal-O-Ring | 2 |
4p-9090 Regulator Gp-Gas Pressure
| 05***41 | Elbow | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 10***27 | Regulator Group-Gas Pressure | 2 |
4p-8326 Regulator Gp-Gas Pressure
| 06***93 | Bushing-Reducer; (1/2-14 Nptf) | 1 |
| 09***81 | Spacer; (10.5x20x10.0mm Thk) | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
7e-8190 Regulator Gp-Gas Pressure
| 17***01 | Kit-Repair; (65-mm Regulator) | 1 |
| 7E***90 | Regulator Group-Gas Pressure | 1 |
105-8847 Regulator Gp-Gas Pressure
| 06***93 | Bushing-Reducer; (1/2-14 Nptf) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 10***47 | Regulator Group-Gas Pressure | 1 |
233-7973 Separator Gp-Water -Primary Fuel Filter
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 23***73 | Separator Group-Water; -Primary Fuel Filter | 1 |
4p-7380 Separator Gp-Water
| 13***07 | Filter Element As-Fuel; (Water Separator) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 4 |
7e-1585 Throttle As
| 6L***96 | Screw-Pin; (10-32x0.75-In) | 2 |
| 7E***52 | Kit-Shaft & Bearing; (Throttle) | 0 |
| 7E***65 | Lever As-Stop | 2 |
7e-1589 Throttle Gp
| 6L***96 | Screw-Pin; (10-32x0.75-In) | 2 |
| 7E***65 | Lever As-Stop | 2 |
| 7E***89 | Throttle Group | 1 |
7e-9203 Throttle Gp
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 8 |
7e-8284 Throttle Gp
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 4B***88 | Bolt (5/16 X 28.58 mm); (5/16-18x1.125-In) | 1 |
| 4W***92 | Gasket | 1 |
7e-1598 Valve Gp-Fuel
| 12***29 | Plate | 1 |
| 12***30 | Piston | 1 |
| 1H***04 | Screw Assembly Adapter To Mounting Plate; Screw Assembly-Adapter To Mounting Plate | 6 |
Generators
149-6130 Regulator As-Voltage
| 14***30 | Regulator As-Automatic Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
9y-8400 Regulator Gp-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
142-4455 Adapter Gp-Generator Coupling
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 11***77 | Sleeve-Wear | 1 |
| 12***11 | Adapter As | 1 |
6i-4883 Air Filter Gp-Generator
| 1P***86 | Bolt--Alternator Support To Circuit | 2 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
| 4B***38 | Screw-Machine; (10-32x15.88-mm) | 2 |
121-5422 Air Filter Gp-Generator
| 12***22 | Air Filter Group-Generator | 1 |
| 12***11 | Frame As-Air Filter | 1 |
| 12***13 | Filter Element-Air; (Generator) | 1 |
216-9721 Bracket Gp-Mounting
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 11***77 | Sleeve-Wear | 1 |
| 11***68 | Retainer-Bearing | 2 |
236-2490 Cable Gp-Generator Ground -Neutral
| 23***54 | Cable; (Grounding) | 1 |
| 23***90 | Cable Group-Generator Ground; -Neutral | 1 |
7c-2561 Connection Gp-Generator Leads
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 3 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 30 |
| 5S***82 | Capscrew; (Hex Hd) (1/2-13x1 3/8, Gd8, Z) | 12 |
9y-0873 Connection Gp-Generator Leads
| 1D***17 | Nut-Plate And Angle Assembly To Hydraulic And Fuel Tanks; Nut Plate And Angle Assembly To Hydraulic And Fuel Tanks | 4 |
| 2A***39 | Bolt,Machine Tube To Torque Converter And Tube To Oil Cooler | 2 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 2 |
106-7715 Connection Gp-Generator Leads
| 10***15 | Connection Group-Generator Leads | 1 |
| 5S***82 | Capscrew; (Hex Hd) (1/2-13x1 3/8, Gd8, Z) | 9 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 28 |
106-7707 Connection Gp-Generator Leads
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 10***07 | Connection Group-Generator Leads | 1 |
| 10***11 | Bar-Neutral | 1 |
121-9480 Connection Gp-Terminal Strip
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 12***80 | Connection Group-Terminal Strip | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
122-0328 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 9 |
| 12***28 | Connection Group-Terminal Strip | 1 |
116-9827 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
147-7258 Connection Gp-Terminal Strip
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 2 |
| 12***13 | Panel As | 1 |
| 12***14 | Panel As | 1 |
122-0329 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 12 |
| 12***29 | Connection Group-Terminal Strip | 1 |
121-5132 Connection Gp-Terminal Strip
| 12***32 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 12 |
| 5N***85 | Tape-Electrical; (Varnished Cambric) | 1 |
154-1902 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
115-3056 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 34 |
122-0331 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 18 |
| 12***31 | Connection Group-Terminal Strip | 1 |
9y-0903 Connection Gp-Terminal Strip
| 03***25 | Terminal-Ring; (For 3/8" Fastener) | 1 |
| 18***11 | Cable; (0000-Ga, Dark Green)(97-cm) | 0 |
| 1D***17 | Nut-Plate And Angle Assembly To Hydraulic And Fuel Tanks; Nut Plate And Angle Assembly To Hydraulic And Fuel Tanks | 1 |
9y-2582 Connection Gp-Terminal Strip
| 11***02 | Strip-Terminal, Plate | 3 |
| 11***03 | Strip-Terminal | 1 |
| 11***04 | Bracket | 1 |
118-9430 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 16 |
| 11***32 | Strip-Terminal | 3 |
126-7571 Connection Gp-Terminal Strip
| 12***30 | Strip Group-Terminal | 1 |
| 12***71 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 30 |
147-0902 Connection Gp-Terminal Strip
| 14***02 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 12 |
| 5N***85 | Tape-Electrical; (Varnished Cambric) | 1 |
122-0330 Connection Gp-Terminal Strip
| 03***95 | Terminal-Ring; (0000-Ga, 3/8-In Screw) | 2 |
| 12***95 | Cable As-Extension | 15 |
| 12***30 | Connection Group-Terminal Strip | 1 |
147-0904 Connection Gp-Terminal Strip
| 14***04 | Connection Group-Terminal Strip | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 12 |
| 5N***85 | Tape-Electrical; (Varnished Cambric) | 0 |
154-1901 Connection Gp-Terminal Strip
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 36 |
122-3487 Conversion Gp-Generator
| 11***12 | Box Group-Extension Terminal; (Low Voltage) | 1 |
| 12***94 | Box & Mounting Group; -Cable Access | 1 |
| 12***87 | Conversion Group-Generator | 1 |
5n-9421 Exciter & Heat Sink As
| 3N***45 | Screw-Forming; (5/16-18x1-In) | 4 |
| 4B***03 | Bolt (4 In. Long)--101.6 mm) | 3 |
| 4P***53 | Hub-Holder | 1 |
142-4450 Exciter Gp -Permanent Magnet
| 10***49 | Rotor As-Magnetic | 1 |
| 12***25 | Stator As-Magnet | 1 |
| 14***50 | Exciter Group; -Permanent Magnet | 1 |
215-2402 Exciter Gp -Power
| 20***24 | Rotor-Exciter | 1 |
| 21***02 | Exciter Group; -Power | 1 |
| 21***04 | Stator-Exciter | 1 |
142-4448 Exciter Gp -Power
| 10***50 | Rotor-Exciter | 1 |
| 12***12 | Stator-Exciter | 1 |
| 14***48 | Exciter Group; -Power | 1 |
178-1618 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 17***17 | Generator Group | 1 |
| 17***18 | Generator Ar | 1 |
147-9444 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***43 | Generator Group | 1 |
144-1840 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***39 | Generator Group | 1 |
147-9442 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***41 | Generator Group | 1 |
7c-3068 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
144-1976 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***75 | Generator Group | 1 |
144-2028 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***27 | Generator Group | 1 |
144-1750 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***49 | Generator Group | 1 |
6i-4854 Generator Ar
| 22***84 | Film-Identification; (Cat) | 2 |
| 22***24 | Film-Warning; (Automatic Engine Start) | 2 |
| 22***27 | Film-Warning; (Hot Surface) | 2 |
284-8214 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
144-1752 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***51 | Generator Group | 1 |
144-1838 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***37 | Bracket, Generator Group | 1 |
144-2030 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***29 | Generator Group | 1 |
144-1768 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***67 | Generator Group | 1 |
7c-3069 Generator Ar
| 10***61 | Plate-Generator; (Grease Bearing) | 1 |
| 1W***48 | Plate-Serial Number On Upper R.H.Side Of | 1 |
| 22***84 | Film-Identification; (Cat) | 2 |
144-1978 Generator Ar
| 11***08 | Film-Instruction; (Generator Notice) | 1 |
| 13***54 | Kit-Parts; (Generator) | 1 |
| 14***77 | Generator Group | 1 |
144-1767 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
7w-8678 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 8 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
147-9443 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1977 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
7w-8677 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***43 | Screw; (1/4-20x0.625-In) | 10 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
6i-4853 Generator Gp
| 03***84 | Plug 12.7 mm(.50 In.) Dia. | 4 |
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 05***71 | Mount | 4 |
147-9441 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1751 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1749 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
178-1617 Generator Gp
| 12***39 | Connection Group-Electrical; -Thermocouple | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1837 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
284-8213 Generator Gp
| 14***87 | Cover Group-Generator; -Coupling | 1 |
| 14***50 | Exciter Group; -Permanent Magnet | 1 |
| 14***52 | Rectifier Group-Revolving | 1 |
144-1975 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-2029 Generator Gp
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-1839 Generator Gp
| 12***40 | Connection Group-Electrical; -Rtd | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
144-2027 Generator Gp
| 12***38 | Connection Group-Electrical; -Basic | 1 |
| 12***97 | Sleeve-Shaft | 1 |
| 14***87 | Cover Group-Generator; -Coupling | 1 |
125-2114 Heat Sink As
| 11***22 | Rectifier; (Positive) | 1 |
| 11***24 | Rectifier; (Negative) | 1 |
| 11***56 | Washer; (5.6x7.8x0.5-mm Thk) | 4 |
9y-7174 Heat Sink As-Negative
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***15 | Strip-Terminal; (Terminal) | 1 |
5n-5030 Heat Sink As-Negative
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***15 | Strip-Terminal; (Terminal) | 1 |
5n-5027 Heat Sink As-Positive
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***59 | Resistor Assem. | 1 |
9y-7175 Heat Sink As-Positive
| 3D***99 | Screw-Machine; (8-32x0.875-In) | 2 |
| 3N***58 | Tube (Insulating) | 2 |
| 3N***59 | Resistor Assem. | 1 |
7w-8708 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 6 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 2 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
104-6203 Installation Ar-Generator
| 10***03 | Installation Ar-Generator | 1 |
| 13***33 | Shim Pack; (Includes 13-Shims) | 4 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 4 |
247-0305 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 4 |
| 24***05 | Installation Ar-Generator | 1 |
| 24***08 | Coupling Group-Flexible; -Generator | 1 |
153-0191 Installation Ar-Generator
| 13***33 | Shim Pack; (Includes 13-Shims) | 6 |
| 15***91 | Installation Ar-Generator | 1 |
| 4B***03 | Setscrew-Square Head; (3/4-10x2-In) | 4 |
4w-8212 Insulator -Circuit Breaker Mount
| 4W***12 | Insulator; -Circuit Breaker Mount | 1 |
126-6604 Kit-Generator Repair
| 10***60 | Ball Bearing | 1 |
| 10***61 | Ball Bearing | 1 |
| 11***22 | Rectifier; (Positive) | 1 |
147-9521 Mounting Gp-Generator
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 11***77 | Sleeve-Wear | 1 |
| 11***68 | Retainer-Bearing | 2 |
124-1563 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
243-4270 Mounting Gp-Voltage Regulator
| 24***70 | Mounting Group-Voltage Regulator | 1 |
| 4L***25 | Lockwasher | 4 |
| 7X***01 | Bolt-Plt; (1/4unc X 1 1/4) | 4 |
242-3487 Mounting Gp-Voltage Regulator
| 03***75 | Washer; (0.266x1.25x0.06-In Thk) | 6 |
| 24***87 | Mounting Group-Voltage Regulator | 1 |
| 24***64 | Spacer; (8.5x12.7x94.3-mm Thk) | 3 |
123-8591 Mounting Gp-Voltage Regulator
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 24***26 | Washer-Hard; (7.2x32x1-mm Thk) | 6 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 1 |
5n-0593 Plate Gp-Generator Coupling
| 5N***93 | Plate Group-Generator Coupling | 1 |
| 5N***78 | Plate As | 1 |
| 5N***79 | Shim .80mm(.031in)Thk | 3 |
298-3817 Rectifier Gp-Revolving
| 11***72 | Harness As-Wiring; (Rectifier) | 1 |
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 29***48 | Heat Sink As | 1 |
142-4452 Rectifier Gp-Revolving
| 11***72 | Harness As-Wiring; (Rectifier) | 1 |
| 12***14 | Heat Sink As | 1 |
| 14***52 | Rectifier Group-Revolving | 1 |
5n-9440 Regulator As-Voltage
| 1N***67 | Circuit Breaker As; (7.5 Amp) | 1 |
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***87 | Transformer As. | 2 |
5n-9093 Regulator As-Voltage
| 4W***79 | Guide-Card | 4 |
| 4W***33 | Board As; (M3) | 1 |
| 5N***19 | Board Assem.; (M2) | 1 |
5n-9439 Regulator As-Voltage
| 3N***50 | Fuse (10 Amps); Fuse - 15 Amp. | 1 |
| 4W***87 | Transformer As. | 1 |
| 4W***40 | Protector (Thermal) | 1 |
5n-5081 Regulator As-Voltage
| 4W***79 | Guide-Card | 4 |
| 5N***19 | Board Assem.; (M2) | 1 |
| 5N***81 | Regulator As; (Voltage-Perm. Magnet) | 1 |
155-3832 Regulator As-Voltage -Digital
| 15***32 | Regulator As-Voltage; -Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
309-1019 Regulator As-Voltage
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 30***19 | Regulator As-Voltage; -Digital | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
7e-8261 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
202-8634 Regulator As-Voltage -Digital
| 20***34 | Regulator As-Voltage; -Sensing | 1 |
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 8 |
155-3835 Regulator As-Voltage -Digital
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 4 |
7e-8262 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
314-7755 Regulator As-Voltage -Digital
| 24***58 | Film-Warning; (Shock, Electrocution Hazard)(Shock, Electrocution Hazard) | 1 |
| 31***55 | Regulator As-Voltage; -Generator | 1 |
235-5725 Regulator As-Voltage -Digital
| 21***84 | Film-Warning; (Shock, Electrocution Hazard)(Voltage Regulator) | 1 |
| 23***25 | Regulator As-Voltage; -Digital-Generator | 1 |
7c-2662 Regulator As-Voltage
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
| 4P***26 | Block-Fuse | 1 |
155-3820 Regulator As-Voltage
| 15***20 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
114-5510 Regulator As-Voltage
| 11***10 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
114-5511 Regulator As-Voltage
| 11***11 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
105-4401 Regulator As-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
155-3819 Regulator As-Voltage
| 15***19 | Regulator As-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 2 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
116-7846 Regulator Gp-Voltage -Digital
| 11***46 | Regulator Group-Voltage; -Digital | 1 |
| 12***87 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
121-6200 Regulator Gp-Voltage
| 12***00 | Regulator Group-Voltage | 1 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
| 15***20 | Regulator As-Voltage | 1 |
108-1872 Regulator Gp-Voltage
| 10***72 | Regulator Group-Voltage | 1 |
| 15***24 | Regulator Group-Voltage | 1 |
| 7E***74 | Film-Instruction; (Voltage Control Adjustment) | 1 |
121-6201 Regulator Gp-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 12***01 | Regulator Group-Voltage | 1 |
| 12***91 | Mounting Group-Voltage Regulator | 1 |
116-7847 Regulator Gp-Voltage
| 11***47 | Regulator Group-Voltage | 1 |
| 15***33 | Regulator As; (Voltage) | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
121-6203 Regulator Gp-Voltage -Digital
| 12***03 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
108-1870 Regulator Gp-Voltage
| 10***01 | Regulator As-Voltage | 1 |
| 10***70 | Regulator Group-Voltage | 1 |
| 7E***74 | Film-Instruction; (Voltage Control Adjustment) | 1 |
116-7850 Regulator Gp-Voltage
| 11***50 | Regulator Group-Voltage | 1 |
| 15***36 | Regulator As; (Voltage) | 1 |
| 2F***06 | Screw-Machine (6-32x. 25in); (6-32x0.25-In) | 25 |
155-3824 Regulator Gp-Voltage
| 15***24 | Regulator Group-Voltage | 1 |
| 4B***42 | Screw-Machine; (12-24x0.375-In) | 1 |
| 4B***74 | Washer; (6.4x14.5x1.6-mm Thk) | 4 |
121-6202 Regulator Gp-Voltage -Digital
| 12***02 | Regulator Group-Voltage; -Digital | 1 |
| 12***63 | Mounting Group-Voltage Regulator | 1 |
| 15***32 | Regulator As-Voltage; -Digital | 1 |
242-9703 Regulator Gp-Voltage -Digital
| 21***48 | Film-Instruction; (Voltage Control Adjustment) | 1 |
| 24***03 | Regulator Group-Voltage; -Digital | 1 |
| 24***05 | Transformer Group-Potential | 1 |
116-7849 Regulator Gp-Voltage -Digital
| 11***49 | Regulator Group-Voltage; -Digital | 1 |
| 12***86 | Film-Instruction; (Voltage Adjustment) | 1 |
| 15***35 | Regulator As-Voltage; -Sensing, Digital | 1 |
7c-2709 Rotor Gp-Generator
| 10***60 | Ball Bearing | 1 |
| 1N***10 | Ring-Retaining | 1 |
| 2N***36 | Screw; (5/16-18x1.25-In) | 1 |
215-3159 Rotor Gp-Generator
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 12 |
| 10***61 | Ball Bearing | 2 |
| 12***03 | Hub-Flexible Coupling | 1 |
145-7454 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 13***01 | Kit-Rotor Lead | 1 |
| 14***54 | Rotor Group-Generator | 1 |
215-3148 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 13***01 | Kit-Rotor Lead | 1 |
| 21***48 | Rotor Group-Generator | 1 |
215-3144 Rotor Gp-Generator
| 10***61 | Ball Bearing | 1 |
| 13***01 | Kit-Rotor Lead | 1 |
| 21***44 | Rotor Group-Generator | 1 |
145-7455 Rotor Gp-Generator
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 12 |
| 10***61 | Ball Bearing | 2 |
| 12***03 | Hub-Flexible Coupling | 1 |
145-6002 Screen Gp-Air
| 10***51 | Screen As; (Air) | 2 |
| 14***02 | Screen Group-Air; -Generator | 1 |
| 3E***23 | Bolt-Flange Head; (1/4-20x1-In) | 4 |
145-6000 Screen Gp-Air -Generator
| 12***45 | Screen As-Air | 2 |
| 14***00 | Screen Group-Air; -Generator | 1 |
| 3E***23 | Bolt-Flange Head; (1/4-20x1-In) | 4 |
148-2610 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
148-2614 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
148-2616 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
145-7532 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
148-2617 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
145-7524 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
145-7529 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
148-2613 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
213-2266 Stator Gp-Main
| 21***66 | Stator Group-Main | 1 |
148-2612 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
145-7520 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
145-7521 Stator Gp-Main
| 00***92 | Screw-Washer Head; (1/4-20x0.5-In) | 9 |
| 03***43 | Screw; (1/4-20x0.625-In) | 17 |
| 11***49 | Cover-Stator | 1 |
Lubrication System
4p-8312 Breather Gp -Crankcase
| 03***31 | Seal-O-Ring | 1 |
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 4 |
| 4P***12 | Breather Group; -Crankcase | 1 |
7n-1875 Filler Gp-Engine Oil -Cylinder Block
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 2W***52 | Gasket | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
134-0975 Filter Gp-Engine Oil -Duplex
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
4w-6874 Filter Gp-Engine Oil -Rh
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
4w-9968 Filter Gp-Engine Oil -Duplex
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
130-8164 Gauge Gp-Oil Filter Press Diff
| 11***90 | Hose As | 2 |
| 13***64 | Gauge Group-Oil Filter Press Diff | 1 |
| 13***65 | Lines Group-Instrument Panel; -Rh | 1 |
7c-6366 Gauge Gp-Oil Level (Dipstick)
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 4P***84 | Gauge As-Oil Level (Dipstick) | 1 |
7c-9784 Gauge Gp-Oil Level (Dipstick) -Deep Sump
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 4 |
7e-6342 Gauge Gp-Oil Level (Dipstick)
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 4B***40 | Cover; (Prelubrication) | 1 |
| 4P***84 | Gauge As-Oil Level (Dipstick) | 1 |
235-4434 Hose As
| 23***34 | Hose As | 1 |
| 3N***69 | Hose As | 1 |
235-1780 Hose As
| 23***80 | Hose As | 1 |
| 3N***10 | Hose As | 1 |
235-4431 Hose As
| 23***31 | Hose As | 1 |
| 3N***68 | Hose As | 1 |
3n-4513 Hose As
| 3N***13 | Hose As | 1 |
3n-4869 Hose As
| 3N***69 | Hose As | 1 |
134-3749 Lines Gp-Engine Oil
| 06***56 | Seal-O-Ring | 4 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
5n-6241 Lines Gp-Prelubrication -Rh
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 13***45 | Clip-Loop | 3 |
113-4238 Lines Gp-Prelubrication
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
| 03***48 | Elbow (3/4" Tapped Pumps) - 2nd Type | 1 |
| 03***30 | Hose As | 1 |
4w-5770 Lines Gp-Turbocharger Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
9y-3476 Lines Gp-Turbocharger Oil
| 00***73 | Elbow, Each Including: | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 4 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
7w-0053 Pump Gp-Engine Oil -2-Section Gear
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 9 |
| 11***49 | Gasket | 1 |
7n-8715 Pump Gp-Engine Oil -2-Section Gear
| 29***87 | Seal-O-Ring | 1 |
| 4S***82 | Bolt 7.25 In. (18.42 cm) Long | 3 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 3 |
2n-7613 Pump Gp-Prelubrication
| 2N***13 | Pump Group-Prelubrication | 1 |
| 7N***09 | Capacitor | 1 |
| 7N***10 | Motor Assem. | 1 |
113-4174 Pump Gp-Prelubrication
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
113-6996 Pump Gp-Prelubrication
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
264-1452 Pump Gp-Sump
| 26***52 | Pump Group-Sump | 1 |
| 7W***04 | Pump Group-Sump | 1 |
229-8349 Pump Gp-Sump
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 4 |
5n-6237 Pump Gp-Sump
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 2 |
| 3N***97 | Pin-Tapered | 2 |
| 3N***99 | Gasket Set; (Includes 4 Gaskets) | 1 |
7w-9704 Pump Gp-Sump
| 00***63 | Elbow, 90 Deg Street, 3/4in. N.P.T. | 1 |
| 0L***01 | Nut; (1-1/2-12-Thd) | 1 |
| 1K***37 | Elbow-Pipe | 1 |
7w-7319 Regulator Gp-Oil Level
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
5n-4659 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
216-8347 Regulator Gp-Oil Level
| 03***67 | Connector-Flared -- Adapter To Hose As. | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
7w-3816 Valve Gp-Fluid Control -Duplex Oil
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 2W***13 | Cover Assem. | 1 |
| 2W***10 | Valve As-Oil; (Duplex) | 1 |
147-3738 Valve Gp-Fluid Sampling -Oil
| 14***38 | Valve Group-Fluid Sampling; -Engine Oil | 1 |
| 7X***87 | Valve As-Fluid Sampling; (Oil Cooler) | 1 |
| 8C***45 | Cap-Dust; (Engine Oil Quick Disconnect) | 1 |
Operator Station
4p-9571 Box Gp-Control Panel
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***01 | Kit-Marker | 1 |
| 10***02 | Terminal; (Single) | 50 |
195-4769 Box Gp-Control Panel
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 2 |
| 11***70 | Bushing; (Capped) | 2 |
| 12***16 | Mount-Flexible | 4 |
194-2461 Box Gp-Control Panel
| 12***72 | Seal; (135-cm) | 0 |
| 15***15 | Latch As | 2 |
| 15***23 | Hinge As | 2 |
123-6323 Box Gp-Control Panel
| 12***97 | Mounting Group-Instrument Panel | 1 |
| 12***23 | Box Group-Control Panel | 1 |
| 19***69 | Box Group-Control Panel | 1 |
9y-2907 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 9Y***47 | Film-Identification; (Control Panel) | 1 |
| 9Y***07 | Control Group-Alarm Module | 1 |
130-3332 Control Gp-Alarm Module
| 13***32 | Control Group-Alarm Module | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
9y-2906 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 7C***30 | Film-Identification | 1 |
| 8C***46 | Strap-Jumper | 1 |
9w-3577 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 17***90 | Wire; (18-Ga, White)(42.5-cm Ea) | 0 |
| 2W***80 | Boot-Switch | 1 |
130-3333 Module Gp-Alarm
| 13***26 | Film-Control Panel; (Custom Alarm Module Idents) | 1 |
| 13***27 | Film-Control Panel; (Custom Alarm Module) | 1 |
| 13***32 | Control Group-Alarm Module | 1 |
130-3349 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 9S***02 | Plug-O-Ring; (Straight Thread O-Ring) | 1 |
7e-1234 Control Gp-Alarm Module
| 13***49 | Control Group-Alarm Module | 1 |
| 7E***34 | Control Group-Alarm Module | 1 |
| 9Y***76 | Film; (Annunciator)(Control Panel) | 1 |
101-0225 Control Gp-Emcp Electronic
| 10***22 | Housing As; (Transformer Box-Emcp Ii) | 1 |
| 10***25 | Control Group-Emcp Electronic | 1 |
| 10***03 | Channel As; (Transformer-Emcp Ii) | 1 |
118-0175 Control Gp-Emcp Electronic
| 10***27 | Screw-Pan Head; (10-24x0.25-In) | 8 |
| 11***75 | Control Group-Emcp Electronic | 1 |
| 15***65 | Kit-Connecting Plug; (8-Pin)(Electronic Control Channel) | 1 |
137-5525 Control Gp-Emcp Electronic
| 13***25 | Control Group-Emcp Electronic | 1 |
| 1S***74 | Seal-O-Ring (164.69mm Id) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
151-6260 Control Gp-Emcp Electronic
| 15***60 | Control Group-Emcp Electronic | 1 |
| 1S***74 | Seal-O-Ring (164.69mm Id) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
154-3864 Control Gp-Emcp Electronic
| 15***50 | Control & Cover Group-Eng Elek | 1 |
| 15***64 | Control Group-Emcp Electronic | 1 |
| 15***65 | Wiring Group-Engine | 1 |
151-6261 Control Gp-Emcp Electronic
| 15***60 | Control Group-Emcp Electronic | 1 |
| 15***61 | Control Group-Emcp Electronic | 1 |
| 4P***07 | Film-Emcp Ii; (Graphic/Text) | 1 |
137-5526 Control Gp-Emcp Electronic
| 13***15 | Film-Control Panel; (Generator Set Control +)(Emcpii+) | 1 |
| 13***25 | Control Group-Emcp Electronic | 1 |
| 13***26 | Control Group-Emcp Electronic | 1 |
3e-7848 Control Gp-Engine Monitoring
| 1S***91 | Screw-Machine; (6-32x.25in) | 16 |
| 2L***77 | Terminal; (14-Ga To 16-Ga, 1/4-In Screw)(14-16 Gage, 6.4mm Screw) | 4 |
| 3E***73 | Relay As | 7 |
3e-8542 Control Gp-Engine Monitoring
| 3E***42 | Control Group-Engine Monitoring | 1 |
6v-6149 Control Gp-Engine Monitoring -Spark Ignited
| 6V***48 | Control Group-Engine Monitoring | 1 |
| 6V***49 | Control Group-Engine Monitoring; -Spark Ignited | 1 |
| 8C***88 | Seal-Security | 1 |
124-4564 Control Gp-Engine Monitoring
| 12***64 | Control Group-Engine Monitoring | 1 |
| 20***28 | Control Group-Engine Electronic | 1 |
108-7871 Control Gp-Engine Monitoring
| 10***81 | Film-Control Panel | 1 |
| 10***71 | Control Group-Engine Monitoring | 1 |
| 6V***48 | Control Group-Engine Monitoring | 1 |
6v-6148 Control Gp-Engine Monitoring
| 3E***36 | Film-Identification; (Status) | 1 |
| 3E***48 | Control Group-Engine Monitoring | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
147-8180 Control Gp-Engine Monitoring
| 10***50 | Control & Cover Group-Eng Elek | 1 |
| 14***80 | Control Group-Engine Monitoring | 1 |
| 14***81 | Wiring Group-Sensor | 1 |
125-3668 Control Gp-Engine Monitoring
| 12***64 | Control Group-Engine Monitoring | 1 |
| 12***68 | Control Group-Engine Monitoring | 1 |
121-5421 Filter As-Electronic
| 12***21 | Filter As-Electronic; -Radio Frequency Interference | 1 |
145-7571 Filter Gp-Electronic -Radio Frequency Interference
| 12***21 | Filter As-Electronic; -Radio Frequency Interference | 1 |
| 14***70 | Bar; (Grounding) | 2 |
| 14***71 | Filter Group-Electronic; -Radio Frequency Interference | 1 |
130-8170 Gauge As-Pressure -Auxiliary Water
| 03***61 | Elbow; (45 Degree) | 1 |
| 11***97 | Film-Gauge Identification; (Auxiliary Water Pressure) | 1 |
| 11***91 | Hose As | 1 |
107-9023 Gauge As-Pressure -Engine Oil
| 03***41 | Elbow; (7/16-20 Str Thd) | 1 |
| 03***61 | Elbow; (45 Degree) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
107-9026 Gauge As-Pressure -Differential Oil
| 10***04 | Lines Group-Instrument Panel | 1 |
| 10***26 | Gauge As-Pressure; -Differential Oil | 1 |
| 11***91 | Hose As | 2 |
130-8169 Gauge As-Pressure -Engine Oil
| 03***41 | Elbow; (7/16-20 Str Thd) | 1 |
| 03***61 | Elbow; (45 Degree) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
108-3921 Gauge Gp-Air Inlet Temperature
| 10***21 | Gauge Group-Air Inlet Temperature | 1 |
| 2W***15 | Plate-Air Inlet Manifold; (Cooler Coolant) | 1 |
| 3E***36 | Gauge-Temperature; (Manifold Air Temperature) | 1 |
3n-9012 Ammeter Gp
| 3N***90 | Film-Gauge Identification; (Ammeter) | 1 |
| 3N***92 | Ammeter As; (60-Ampere) | 1 |
| 3N***12 | Gauge Group-Ammeter; (60-Ampere) | 1 |
107-9028 Gauge Gp-Coolant Pressure
| 10***28 | Gauge Group-Coolant Pressure | 1 |
| 11***97 | Film-Gauge Identification; (Auxiliary Water Pressure) | 1 |
| 11***91 | Hose As | 1 |
130-8160 Gauge Gp-Coolant Pressure
| 03***61 | Elbow; (45 Degree) | 1 |
| 11***91 | Hose As | 1 |
| 12***67 | Gauge As-Pressure; (Engine Coolant) | 1 |
107-9024 Gauge Gp-Coolant Temperature
| 10***24 | Gauge Group-Coolant Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
108-3854 Gauge Gp-Coolant Temperature
| 10***54 | Gauge Group-Coolant Temperature | 1 |
| 3E***37 | Gauge Group-Coolant Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
107-9021 Gauge Gp-Manifold Air Temp
| 10***21 | Gauge Group-Manifold Air Temp | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 4 |
| 2W***15 | Plate-Air Inlet Manifold; (Cooler Coolant) | 1 |
130-8166 Gauge Gp-Manifold Pressure
| 11***90 | Hose As | 1 |
| 13***66 | Gauge Group-Manifold Pressure | 1 |
| 13***68 | Lines Group-Instrument Panel | 1 |
107-9025 Gauge Gp-Manifold Pressure
| 03***61 | Elbow; (45 Degree) | 1 |
| 10***22 | Lines Group-Instrument Panel | 1 |
| 10***25 | Gauge Group-Manifold Pressure | 1 |
107-9029 Gauge Gp-Oil Temperature
| 10***29 | Gauge Group-Oil Temperature | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 10 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
107-9030 Gauge Gp-Vacuum
| 03***61 | Elbow; (45 Degree) | 1 |
| 10***22 | Lines Group-Instrument Panel | 1 |
| 10***30 | Gauge Group-Vacuum | 1 |
130-8163 Gauge Gp-Vacuum
| 11***90 | Hose As | 1 |
| 13***63 | Gauge Group-Vacuum | 1 |
| 13***68 | Lines Group-Instrument Panel | 1 |
107-9032 Gauge Gp-Water Pressure Diff
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***32 | Gauge Group-Water Pressure Diff | 1 |
130-8162 Gauge Gp-Water Pressure Diff
| 03***61 | Elbow; (45 Degree) | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 11***96 | Film-Gauge Identification; (Engine Coolant Pressure) | 1 |
6i-2118 Gauge Gp-Water Pressure Diff
| 3E***35 | Gauge As-Pressure; (Water) | 1 |
| 4B***49 | Nut-Valve To Bracket; 3.18mm(.125in)Thk | 2 |
| 6I***18 | Gauge Group-Water Pressure Diff | 1 |
104-5904 Lines Gp-Instrument Panel
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 1 |
| 10***04 | Lines Group-Instrument Panel | 1 |
243-5029 Lines Gp-Instrument Panel -Water Pressure
| 00***40 | Connector; (Flared) | 1 |
| 1B***13 | Bolt,Machine Governor And Decelerator Control | 2 |
| 24***29 | Lines Group-Instrument Panel; -Water Pressure | 1 |
130-8165 Lines Gp-Instrument Panel -Rh
| 03***46 | Elbow, 90 Deg Adj., 1/4in. J.I.C. X 7/16in.-14 Str. Thd. | 1 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 1 |
| 13***65 | Lines Group-Instrument Panel; -Rh | 1 |
104-5722 Lines Gp-Instrument Panel
| 00***40 | Connector; (Flared) | 1 |
| 06***95 | Elbow (Between Fuel Lines) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
130-8168 Lines Gp-Instrument Panel
| 00***40 | Connector; (Flared) | 1 |
| 06***95 | Elbow (Between Fuel Lines) | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
243-5031 Lines Gp-Instrument Panel -Water Pressure Differential
| 00***40 | Connector; (Flared) | 1 |
| 1B***13 | Bolt,Machine Governor And Decelerator Control | 2 |
| 24***30 | Tube As | 1 |
107-9020 Meter Gp-Service
| 10***20 | Meter Group-Service | 1 |
| 2W***60 | Plug As | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 6 |
118-7862 Meter Gp-Volt
| 10***57 | Voltmeter Group; (24-Volt)(Instrument Panel) | 1 |
| 11***62 | Meter Group-Volt | 1 |
| 11***63 | Bracket | 1 |
130-3350 Control Gp-Alarm Module
| 13***29 | Film-Control Panel; (Alarm Module) | 1 |
| 13***49 | Control Group-Alarm Module | 1 |
| 13***50 | Module Group-Alarm | 1 |
187-9372 Module Gp-Alarm
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 16***08 | Block-Fuse | 1 |
| 18***72 | Module Group-Alarm | 1 |
121-4707 Module Gp-Alarm
| 12***07 | Module Group-Alarm | 1 |
| 7E***34 | Control Group-Alarm Module | 1 |
121-4717 Module Gp-Alarm
| 12***17 | Module Group-Alarm | 1 |
| 9Y***06 | Control Group-Alarm Module | 1 |
121-4716 Module Gp-Alarm
| 12***16 | Module Group-Alarm | 1 |
| 9Y***07 | Control Group-Alarm Module | 1 |
9x-0203 Module Gp-Relay Driver
| 2D***63 | Bolt; (1/4-28x1.75-In) | 2 |
| 5P***37 | Washer 5t***54 Plate To 7t***28 Cable As | 2 |
| 9X***03 | Module Group-Relay Driver | 1 |
121-4710 Module Gp-Synchronizing Lights
| 10***71 | Module Group-Synchronizing Lights | 1 |
| 12***10 | Module Group-Synchronizing Lights | 1 |
| 12***88 | Harness As-Panel; -Reverse Power Relay | 1 |
106-5171 Module Gp-Synchronizing Lights
| 10***64 | Cover; (Synchronizing Lights Module) | 1 |
| 10***71 | Module Group-Synchronizing Lights | 1 |
| 17***81 | Nut; (1/4-20-Thd) | 2 |
162-8734 Module Gp-System Communication
| 10***85 | Battery; (Lithium)(Internal Backup) | 1 |
| 10***37 | Film-Display; (Communication Module) | 1 |
| 10***38 | Film-Interface; (Communication Module)(Rear) | 1 |
102-8627 Module Gp-System Communication
| 10***27 | Module Group-System Communication | 1 |
| 16***40 | Module Group-System Communication | 1 |
164-8940 Module Gp-System Communication
| 10***85 | Battery; (Lithium)(Internal Backup) | 1 |
| 10***37 | Film-Display; (Communication Module) | 1 |
| 10***38 | Film-Interface; (Communication Module)(Rear) | 1 |
7w-0919 Mounting Gp-Control Panel
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
| 3K***60 | Nut, Hex (3/8 - 16 Nc, Plastic Insert) | 2 |
104-4704 Mounting Gp-Control Panel -Emcp Ii
| 10***04 | Mounting Group-Control Panel; -Emcp Ii | 1 |
| 1B***76 | Pin,Straight,Headed Governor And Decelerator Control | 1 |
| 3E***65 | Nut-Hard-Self Lock; (1/4unc) | 2 |
120-5297 Mounting Gp-Instrument Panel
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 6 |
101-8925 Mounting Gp-Instrument Panel
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 6 |
7e-7078 Mounting Gp-Instrument Panel
| 1H***38 | Lockwasher, External Tooth (1/4); W/O Freespool Qty Is 6 | 4 |
| 6V***85 | Nut-Full (1/4-20 Thd); (1/4-20-Thd)(Full) | 4 |
| 7C***75 | Seal-Bellows | 1 |
136-6924 Panel Gp-Control
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***25 | Control Group-Emcp Electronic | 1 |
103-6193 Panel Gp-Control
| 10***93 | Panel Group-Control | 1 |
| 10***66 | Film-Control Panel; (Eis) | 1 |
| 10***02 | Terminal; (Single) | 45 |
4p-9566 Panel Gp-Control
| 10***66 | Film-Control Panel; (Eis) | 1 |
| 10***02 | Terminal; (Single) | 45 |
| 10***07 | Switch-Operator; (Secondary Stop Push Button) | 1 |
317-5570 Panel Gp-Control
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 0S***13 | Bolt-- Contactor To Bracket | 2 |
| 10***98 | Panel As; (Emcpii, Subpan) | 1 |
317-5561 Panel Gp-Control
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 0S***13 | Bolt-- Contactor To Bracket | 2 |
| 10***98 | Panel As; (Emcpii, Subpan) | 1 |
121-4712 Panel Gp-Electronic
| 09***21 | Rail-Mounting; (60-cm) | 1 |
| 12***12 | Panel Group-Electronic | 1 |
| 12***26 | Relay Group; -Auxiliary | 1 |
7c-5296 Panel Gp-Instrument
| 21***89 | Nut; (1/4-20-Thd) | 4 |
| 4P***60 | Washer; (Retaining Ring) | 4 |
| 4P***61 | Screw | 4 |
131-1965 Panel Gp-Instrument -Emcp Ii
| 13***33 | Control Group-Alarm Module; (Custom) | 1 |
| 13***50 | Module Group-Alarm | 1 |
| 13***65 | Panel Group-Instrument; -Emcp Ii | 1 |
7e-8270 Panel Gp-Instrument
| 11***65 | Film-Panel; (Instrument) | 1 |
| 2W***99 | Diode As | 1 |
| 3N***14 | Relay As; (24-Volt) | 1 |
307-9794 Plate-Cover
| 30***94 | Plate-Cover, Twelve Point Cap Screw | 1 |
3n-4416 Pyrometer Gp
| 3N***16 | Pyrometer Group | 1 |
108-4503 Pyrometer Gp
| 10***51 | Locknut; (1-11-1/2 Npt-Thd) | 1 |
| 10***03 | Pyrometer Group | 1 |
| 11***70 | Bushing; (Capped) | 1 |
124-3143 Pyrometer Gp
| 12***43 | Pyrometer Group | 1 |
| 19***37 | Wiring Group-Pyrometer | 1 |
| 28***70 | Pyrometer Group; (Exhaust Temperature Scanner) | 1 |
124-3676 Pyrometer Gp
| 12***76 | Pyrometer Group | 1 |
| 19***34 | Wiring Group-Pyrometer | 1 |
| 28***70 | Pyrometer Group; (Exhaust Temperature Scanner) | 1 |
3n-8276 Pyrometer Gp
| 3N***12 | Pyrometer Group; Pyrometer-Single | 1 |
| 3N***76 | Pyrometer Group-Single; Pyrometer Group--Single | 1 |
121-4705 Seal Gp-Enclosure
| 10***72 | Seal; (Control) | 1 |
| 12***05 | Seal Group-Enclosure | 1 |
| 5L***80 | Washer; (0.490x0.875x0.050-In Thk) | 3 |
107-9019 Tachometer Gp
| 10***19 | Tachometer Group | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 6 |
| 7E***59 | Tachometer Group-Electric; Tachometer Group-Electric | 1 |
7e-3159 Tachometer Gp-Electric
| 19***48 | Tachometer Group | 1 |
| 6V***77 | Nut (8-32 Thd) | 2 |
| 7E***59 | Tachometer Group-Electric; Tachometer Group-Electric | 1 |
105-1457 Voltmeter Gp
| 10***57 | Voltmeter Group; (24-Volt)(Instrument Panel) | 1 |
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 2 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 2 |
Prime Package
9y-5587 Accumulator Gp -Uncharged
| 9T***47 | Seal-Kit | 1 |
| 9Y***87 | Accumulator Group; -Uncharged | 1 |
Service Equipment And Supplies
4w-8000 Chart-Control Panel
| 4W***00 | Chart-Control Panel | 1 |
7e-4300 Chart-Instrument Panel
| 7E***00 | Chart-Instrument Panel | 1 |
6l-4502 Chart-Plate & Film
| 10***59 | Film-Warning; (Electric Shock)(Shock Read Man.) | 2 |
| 15***14 | Plate-Information; (Gas Engine) | 1 |
| 1H***50 | Plate-Notice; On L.H. Front Side Cover & Rear R.H. Cover | 2 |
346-3668 Film Gp
| 14***75 | Film-Information; (Oil Drain)(Oil Drain) | 2 |
| 15***18 | Film-Generator Lifting; (Genset Lifting Instructions) | 2 |
| 1P***07 | Film-Symbol; 2 On Bottom Of Upper Frame Below Engine. 2 On Front Of Upper Frame Above Boom Articulation | 4 |
346-3665 Film Gp
| 14***75 | Film-Information; (Oil Drain)(Oil Drain) | 2 |
| 1P***07 | Film-Symbol; 2 On Bottom Of Upper Frame Below Engine. 2 On Front Of Upper Frame Above Boom Articulation | 6 |
| 22***24 | Film-Warning; (Automatic Engine Start) | 2 |
346-3667 Film Gp
| 14***75 | Film-Information; (Oil Drain)(Oil Drain) | 2 |
| 15***18 | Film-Generator Lifting; (Genset Lifting Instructions) | 2 |
| 1P***07 | Film-Symbol; 2 On Bottom Of Upper Frame Below Engine. 2 On Front Of Upper Frame Above Boom Articulation | 4 |
208-7825 Film Gp -Generator
| 20***67 | Film; (Cat) | 2 |
| 20***68 | Film-Caterpillar | 1 |
| 20***25 | Film Group; -Generator | 1 |
305-7470 Film Gp
| 30***33 | . Washer, Film-Identification; (Caterpillar) | 1 |
| 30***40 | Film-Identification; (Cat, Stripe) | 2 |
| 30***70 | Film Group | 1 |
347-7057 Film Gp-International
| 33***41 | Film-Warning; (Shock Hazard, Read Omm) | 1 |
| 33***43 | Film-Warning; (Universal, Read Omm) | 1 |
| 34***57 | Film Group-International | 1 |
4p-3317 Kit-Installation -Exciter
| 4P***17 | Kit-Installation; -Exciter | 1 |
351-1747 Kit-Maintenance
| 13***58 | Seal-O-Ring | 8 |
| 14***16 | Belt-Serpentine; (Alternator) | 1 |
| 31***62 | Spring | 8 |
351-1743 Kit-Maintenance
| 12***72 | Seal-O-Ring | 8 |
| 13***51 | Seal; (Pressure Relief) | 8 |
| 19***18 | Spark Plug; (Ignition) | 8 |
351-1738 Kit-Maintenance
| 1R***26 | Filter Element As-Engine Oil; (Standard Efficiency) | 3 |
| 35***38 | Kit-Maintenance | 1 |
| 6V***49 | Seal-O-Ring; (196.22mm Id) | 2 |
115-5136 Kit-Marine Generator Parts
| 10***61 | Ball Bearing | 1 |
| 11***36 | Kit-Marine Generator Parts | 1 |
| 12***97 | Sleeve-Shaft | 1 |
4p-7282 Kit-Parts -Generator
| 10***60 | Ball Bearing | 1 |
| 11***10 | Regulator As-Voltage | 1 |
| 15***20 | Regulator As-Voltage | 1 |
171-6719 Kit-Parts -Generator
| 17***19 | Kit-Parts; -Generator | 1 |
7e-5034 Kit-Rfi Filter
| 7E***34 | Kit-Rfi Filter | 1 |
| 9Y***68 | Kit-Rfi Filter | 1 |
7w-8710 Kit-Space Heater
| 3N***45 | Screw-Forming; (5/16-18x1-In) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
7w-9967 Kit-Space Heater
| 03***93 | Screw-Machine; (10-32x19.05-mm) | 2 |
| 3N***63 | Strip (Terminal Marker) | 1 |
| 3N***64 | Film-Connection; (Space Heater) | 1 |
140-2304 Programmer-Gov Elek Control
| 14***04 | Programmer-Gov Elek Control | 1 |
137-8533 Shim Pack
| 13***33 | Shim Pack; (Includes 13-Shims) | 1 |
| 13***34 | Shim; (0.025-mm Thk) | 1 |
| 13***35 | Shim; (0.0508-mm Thk) | 1 |
147-4529 Test Gp-Current
| 14***29 | Test Group-Current | 1 |
| 14***54 | Test Kit; (Shaft Current) | 1 |
| 14***56 | Contactor | 1 |
G3508 serial number reference
The engine ID plate sits on the block, typically on the left-hand side near the flywheel housing or front timing cover; a fully packaged Cat generator set also carries a separate PIN plate on the skid frame or control panel. Read the first three characters as the serial-number prefix (engine/unit build code) and the digits that follow as the sequential unit number. On a full 17-character PIN, the prefix plus its sequence number occupy the last eight characters.
| Prefix | Identifies | Notes |
|---|---|---|
| WPM | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build, no Cat generator end/enclosure. One of the most consistently cited G3508 engine prefixes across independent parts/prefix references. |
| WPN | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build, parallel sequence to WPM. Same application class as WPM. |
| 4WD | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build, sold as engine-only for OEM or mechanical-drive/compression packaging. |
| DLR | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build. Same engine-only category as WPM/WPN/4WD. |
| 9TG | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build. Same engine-only category as WPM/WPN/4WD/DLR. |
| 2JF | G3508 gas engine (bare engine) | Bare G3508 industrial gas engine build. Same engine-only category as the other gas-engine prefixes. |
| 9AW | G3508 industrial engine (bare engine) | Listed as G3508 industrial engine rather than gas engine in reference charts; likely a mechanical-drive or industrial application build rather than a packaged genset. Functionally a bare-engine prefix like the gas-engine group. |
| 2TJ | G3508 gen set engine | Engine built specifically for generator-set duty but sold/tracked as an engine unit (e.g. for a non-Cat packager), distinct from a complete Cat-built generator set. |
| CPJ | G3508 generator set (complete package) | Complete Cat-packaged generator set: engine, generator end, and control panel under one PIN. Real-world natural-gas G3508 gen sets are seen in roughly 360-500 kW class depending on frequency/voltage configuration. |
| CPS | G3508 generator set (complete package) | Complete Cat-packaged generator set, same category as CPJ/CPY. Exact production years not documented in available references - verify with a dealer using the full PIN. |
| CPY | G3508 generator set (complete package) | Complete Cat-packaged generator set, same category as CPJ/CPS. |
Frequently asked questions
What engine powers the Caterpillar G3508?
The G3508 is itself the engine: a V-8, 34.5 L (2105 cu in) spark-ignited natural gas engine, turbocharged and aftercooled, with ADEM A3 electronic ignition and speed control. Gross output runs roughly 391-514 bkW (524-690 bhp) at 1200-1400 rpm depending on the emissions rating ordered, and Cat-packaged generator sets built on it are typically seen from about 330 kW to roughly 500 kW continuous, varying by voltage, frequency, and speed selected.
What is the operating weight of the Caterpillar G3508?
Bare-engine net dry weight runs about 3,940-5,420 kg (8,690-11,950 lb), varying by power rating and accessory package; there's no single published figure since it isn't one fixed configuration. A complete Cat-packaged generator set adds the generator end, radiator, control panel, and enclosure on top of the bare-engine weight, and that total varies by kW size and enclosure style. Check the specific unit's nameplate or dealer data sheet for an exact figure.
What replaced the Caterpillar G3508?
On the same 8-cylinder architecture, the G3508B replaced it for new orders, using two-stage aftercooling and a revised combustion setup that cuts engine-out NOx enough to meet current stationary spark-ignited limits without the customer-supplied aftertreatment a plain G3508 usually needs. Gas-compression-specific variants (G3508 LE, G3508J) continue the family for wellhead and gathering duty. A plain new G3508 generator set isn't part of Cat's current line-up; used and rebuilt units still circulate in the resale and parts market.
What G3508 owners discuss
Owners running the G3508 as backup/standby power often mention 'wet stacking' — what causes it and how do you avoid it?
How sensitive is the G3508 to the quality of the fuel gas, and what happens if it isn't pipeline-quality?
Do the per-cylinder detonation/knock sensors on this engine fail often, and what happens if one does?
Is the G3508 the same engine as the newer G3508B, or are they genuinely different?
What electrical or sensor issues come up most often on these gensets?
How long do spark plugs and ignition parts really last, and is that a significant running cost?
What should you check before buying a used Cat G3508 genset?
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Serial-range & configuration variants
This page covers the Caterpillar G3508. Related factory variants of the same model family:
Need a specific G3508 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.