Caterpillarpaving compactorvibratory compactor
Caterpillar CB-214E
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar CB-214E is a compact tandem vibratory smooth-drum roller built for asphalt lift work and general utility compaction, with 1000 mm (39 in) wide steel drums on the standard machine. It carries Caterpillar's 3013C engine across the model line, a naturally aspirated, water-cooled, three-cylinder diesel rated at roughly 24.4 kW (32.7 hp) gross — a simple mechanically governed engine with no electronic controls. Standard operating weight runs approximately 2,450 to 2,490 kg (5,400 to 5,490 lb) depending on tire fitment, with an extra-wide CB-214E XW variant (1400 mm drum) pushing closer to 3,125 kg (6,890 lb). Caterpillar built the CB-214E from roughly 2004 to 2007 as the successor to the CB-214D, which itself replaced the CB-214C. It shares its Operation and Maintenance Manual and core driveline with two siblings built on the same platform: the wider CB-224E (and heavyweight CB-224E HW) and the CB-225E combi roller, which pairs a steel drum with a rubber-tired roller end and adds an emulsion/additive spray tank.
Across the C-to-D-to-E generations, Caterpillar's changes centered on serviceability rather than raw output: sealed, factory-lubricated vibratory pod bearings, extended-life engine and hydraulic oils, clustered service points behind a single access door, and a daily visual-check system instead of scattered grease points. The E-series kept the mechanical, non-electronic 3013C rather than moving to an ECM-controlled engine, which is part of why these rollers remain easy for independent shops to diagnose and repair with basic tools. In today's used and parts market, the CB-214E still turns up in rental fleets and small paving and utility crews because of its low purchase cost, compact footprint for trench and shoulder work, and parts commonality across the CB-214E/CB-224E/CB-225E family. Its age and pre-Tier emissions rating limit it in regions with strict emissions rules, but that same simplicity keeps demand steady among buyers who want a roller without exhaust aftertreatment or electronic fault codes to manage.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar CB-214E specifications
Engine
| Engine model | Cat 3013C (C1.5), naturally aspirated, water-cooled, 4-stroke, 3-cylinder diesel |
| Gross power | 24.4 kW (32.7-32.8 hp) at 2,800 rpm |
| Net power (ISO 9249) | 22.6 kW (30.3 hp) |
| Net power (EEC 80/1269) | 23.0 kW (30.9 hp) |
| Displacement | 1.5 L / 1,496 cc (91.3 cu in) |
| Bore x stroke | 84 x 89-90 mm (3.3 x 3.5 in) |
| Emissions tier | Meets U.S. EPA Tier 2 and EU Stage II emissions standards for this era of build |
Weights
| Operating weight, with ROPS/FOPS | approx. 2,450 kg (5,400 lb) |
| Operating weight, without ROPS/FOPS | approx. 2,390 kg (5,270 lb) |
| Weight on front drum | approx. 1,150 kg (2,540 lb) |
| Weight on rear drum | approx. 1,300 kg (2,870 lb) |
| Ground pressure | Not published in available spec sheets - verify with dealer if required |
Dimensions
| Overall transport length | 2,438 mm (8.0 ft / 96 in) |
| Overall width | 1,100 mm (3.6 ft / 43 in) |
| Compaction / drum width | 1,000 mm (39-39.4 in) |
| Height, with ROPS/FOPS | approx. 2,591-2,602 mm (8.5 ft / 102 in) |
| Wheelbase | approx. 1,730-1,740 mm (5.67-5.70 ft) |
| Drum diameter | 701 mm (27.6 in) |
| Ground clearance | 254 mm (10 in) |
Performance
| Maximum travel speed | 10.1 km/h (6.3 mph) |
| Vibration frequency | 63 Hz (approx. 3,780 vibrations/min) |
| Nominal amplitude, high setting | 2.5 mm (0.1 in) |
| Maximum centrifugal force per drum | 27.0-27.6 kN (6,075-6,205 lb) - varies slightly by configuration/series |
| Gradeability | Not documented in available spec sheets - verify with dealer if required |
Service capacities (summary)
| Fuel tank | 46.6 L (12.3 gal) |
| Hydraulic system | 30.3 L (8.0 gal) |
| Engine oil | 6.1 L (1.6 gal) |
| Cooling system | Not documented in available spec sheets - verify with dealer if required |
| Water spray tank | 147.6 L (39 gal) - relevant service fluid for this compactor's dust/adhesion spray system |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
CB-214E fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 5.7 L (1.5 US gal / 1.3 Imp gal) | Cat Multigrade DEO, API CG-4 / CF-4. Select viscosity by ambient temperature: SAE 0W20 for -40 to 10°C (-40 to 50°F), SAE 0W30 for -40 to 30°C (-40 to 86°F), SAE 5W30 for -30 to 30°C (-22 to 86°F), SAE 5W40 for -30 to 40°C (-22 to 104°F), SAE 10W30 for -20 to 40°C (-4 to 104°F), SAE 15W40 for -15 to 50°C (5 to 122°F). |
| Cooling system | 6.7 L (1.8 US gal / 1.5 Imp gal) | Cat Extended Life Coolant (ELC), topped with Cat ELC Extender at the scheduled interval. Fill to 1 cm below the bottom of the fill pipe. Machines running commercial long-life coolant, Cat DEAC, or a heavy-duty antifreeze/coolant instead of ELC follow Level 1 sampling; ELC-filled systems follow Level 2 sampling. Mix concentration for the lowest expected ambient temperature. |
| Fuel tank | 48 L (12.7 US gal / 10.6 Imp gal); some spec sheets show approximately 46.5 L (12.3 US gal) — varies by configuration/print run | Commercially available diesel fuel meeting the engine's certified fuel spec; ultra-low-sulfur diesel (ULSD) applies. No supplemental fuel additive is specified in the base chart. |
| Hydraulic system and tank | 26 L (6.9 US gal / 5.7 Imp gal) | Cat HYDO, Cat DEO, Cat TDTO, Cat MTO, API CG-4 / CF-4 / CF, or Cat TO-4, chosen by ambient temperature: SAE 0W20 or 0W30 down to -40°C (-40°F) up to 40°C (104°F), SAE 5W30/5W40 for -30 to 40°C (-22 to 104°F), SAE 10W for -20 to 40°C (-4 to 104°F), SAE 30 for 10 to 50°C (50 to 122°F), SAE 10W30 for -20 to 40°C (-4 to 104°F), SAE 15W40 for -15 to 50°C (5 to 122°F), or straight Cat MTO for -25 to 50°C (5 to 104°F). A biodegradable BIO HYDO-HEES option is listed for -25 to 43°C (-13 to 110°F); tank temperature must stay under 100°C (212°F) and it is not for hydraulic circuits with clutches or brakes. |
| Eccentric weight (vibrator) housing, each drum | 2 L (0.5 US gal / 0.44 Imp gal) per housing | Premium synthetic gear and bearing lubricant, ISO viscosity grade 220 with no viscosity-index improvers and a minimum viscosity index of 150, rated -20 to 50°C (-4 to 122°F). |
| Water spray tank, standard | 160 L (42.3 US gal / 35.2 Imp gal) | Clean water only; contaminated water causes spray-system performance and reliability problems. Drain the tank, spray-bar lines, and filter housing completely ahead of freezing conditions. |
| Water spray tank, larger option (if equipped) | 240 L (63.4 US gal / 52.8 Imp gal) | Same as the standard tank: clean water only, drained fully before freezing weather. |
| Grease points (articulation/oscillating bearings, steering cylinder ends) | Spec only, no refill volume published — lubricate to a light bead, not a full purge | General-purpose chassis grease applied sparingly at daily/periodic fittings; overgreasing at the articulation bearing can damage the seals. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar CB-214E maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 3,000 h |
|
| Every 6,000 h |
|
Servicing the CB-214E beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S·O·S oil sampling on the 3013C every 250 hours and hydraulic oil sampling every 500 hours to catch wear before it reaches the vibratory pod bearings or the hydrostatic pump. Pull coolant samples at 250 hours (Level 1) or annually (Level 2) if the system runs Extended Life Coolant. Watch the air filter service indicator daily — a yellow piston in the red zone on this naturally aspirated three-cylinder means restricted intake and black smoke before power loss shows up on the gauges.
Corrective & Common Repairs
Most field calls trace back to drum and tire scrapers running loose, letting asphalt build up on the smooth drums — reset spring tension and swap worn blades before they score the drum shell. A propel lever that creeps out of position needs a tension adjustment at the control linkage, not a hydrostatic pump swap. After any fuel filter or water separator change, prime the system by hand until resistance is felt, or the 3013C will crank without starting. Check the vibratory pump belt separately from the alternator belt.
Overhaul & Rebuild Points
The sealed eccentric weight housings that drive drum vibration need a gear oil change near 3000 hours — skipping it is the leading cause of premature pod bearing failure on this roller. Inspect drum bearings at 1000 hours or every two years. Replace isolation mounts in matched pairs, never one at a time, so the engine and frame stay aligned. Swap the water temperature regulator at 3000 hours or two years, ideally alongside a full coolant flush rather than on its own.
Seasonal & Environment Servicing
Drain the main water tank, spray bar lines, filter housing, and any auxiliary tank completely before frost — a cracked spray manifold on this roller is a cold-weather write-off, not a quick fix. Match tire pressure to whichever tire size is fitted, since the 9.5/65-15 and 8.5/90-15 ranges differ. In hot, dusty paving work, clean the radiator and hydraulic oil cooler cores often; the compact engine bay traps debris fast. Pick engine oil viscosity for the ambient range, down to -40C on a 0W-grade multigrade.
CB-214E common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 146-7472 | Filter Element As-Air | Air intake service | Check fitment → |
| 146-7473 | Filter Element As-Air | Air intake service | Check fitment → |
| 144-6691 | Filter-Oil | Lubrication service | Check fitment → |
| 220-1523 | Filter As-Engine Oil | Lubrication service | Check fitment → |
| 3E-9350 | Switch As-Temperature | Scheduled service item | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
CB-214E fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| Engine Oil Pressure warning lamp (red, oil-can symbol) | Engine oil pressure has dropped below the safe minimum | Low oil level, plugged oil filter, worn oil pump, or a failed pressure switch/sender | Stop the engine immediately, check oil level and filter condition before restarting; do not run the engine until the cause is found |
| Coolant Temperature warning lamp (red, thermometer symbol) | Engine coolant temperature has exceeded the safe operating range | Low coolant level, blocked radiator fins, slipping or broken fan belt, or a stuck thermostat | Idle down and let the engine cool, then check coolant level, radiator core, and belt condition |
| Battery/Alternator Charge warning lamp (red, battery symbol) | Alternator is not charging the battery | Loose or broken drive belt, failed alternator, or a loose/corroded wiring connection | Check belt tension and wiring connections first, then test alternator output |
| Glow Plug/Preheat indicator lamp (amber) | Cold-start preheat cycle is active | Normal function on cold starts; if the lamp will not extinguish or the engine will not start cold, the glow plug circuit has failed | Wait for the lamp to go out before cranking; if it misbehaves, check the glow plug relay, fuse, and element wiring |
| Air Filter Restriction indicator (yellow/red pop-up on the air cleaner housing, not a dash lamp) | Air filter element has reached its service restriction limit | Clogged or dirty primary air filter element | Service or replace the air filter element and reset the restriction indicator |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
CB-214E attachments & work tools
Drum & scraper configuration
Standard smooth steel drums, 1000 mm (39 in) wide front and rear, with retractable scrapers bolted to the drum frame to keep the drum face clean. A non-machined drum-edge finish is offered as a factory option. No pad-foot or sheepsfoot shell-kit is documented for this compact tandem class; the CB-214E is smooth-drum only.
Water/wetting system
Triple-filtration water spray system feeds bars ahead of each drum, with cocoa mats on the scraper assemblies to hold moisture and even out spray distribution across the drum. Standard tank size ranges 150-240 L (40-63 gal), varies by configuration/series; a supplemental auxiliary tank of about 70 L (18.5 gal) is offered as a factory option. Front and rear spray-bar shields are available to protect the spray pattern from wind.
Protective structure (ROPS/FOPS) options
Base machine ships with a fixed ROPS/FOPS frame. A foldable ROPS and a bolt-on sun canopy are offered for low-clearance or shaded-operation jobsites. Light protector grids can be added to guard mounted work lights.
Lighting and signaling package
Optional working-light package or combined roading-and-working-light package, plus a rotating amber beacon (mounts with or without ROPS) and a back-up alarm, cover jobsite visibility and safety needs.
Vibratory-system controls
Hydraulically driven eccentric weights let the operator select front-drum-only, rear-drum-only, or both-drums vibration from a single switch. Nominal amplitude is about 2.5 mm (0.1 in) with frequency near 63 Hz (3780 vpm) and maximum centrifugal force per drum around 27 kN (6075 lbf); a rear-drum vibratory delay ('Delay ON') control staggers rear-drum start for better power management and mat finish.
Operator comfort options
A suspension seat with armrests and fore/aft/height adjustment is offered over the standard non-suspension seat. A heat-retention device for the water system and a traction-control aid are additional options for cold-weather or slick-surface work.
Engine/exhaust accessories
Powered by the Cat 3013C naturally aspirated 3-cylinder diesel meeting U.S. Tier 2 / 97/68/EC Stage II. Optional spark-arrestor muffler and exhaust deflector are offered for enclosed or fire-sensitive worksites.
Mounting/coupler system
As a tandem vibratory roller, the CB-214E has no quick-coupler work-tool system like an excavator. Factory accessories (scrapers, spray bars, beacon, canopy, ROPS, light guards) mount via bolt-on or pinned brackets on the frame and drum group rather than a hydraulic coupler.
All CB-214E assemblies by section
Every catalogued assembly group for the Caterpillar CB-214E. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
140-2469 Air Cleaner Gp
| 14***69 | Air Cleaner Group | 1 |
| 14***72 | Filter Element As-Air; (Primary)(Primary) | 1 |
| 14***73 | Filter Element As-Air; (Secondary)(Inner) | 1 |
156-3474 Air Cleaner Gp
| 14***69 | Air Cleaner Group | 1 |
| 14***90 | Band-Mounting | 1 |
| 15***74 | Air Cleaner Group | 1 |
260-4540 Air Cleaner Gp
| 09***28 | Indicator-Air Filter Change; (Air Filter Service) | 1 |
| 14***69 | Air Cleaner Group | 1 |
| 14***90 | Band-Mounting | 1 |
206-5524 Cover Gp-Air Inlet
| 17***05 | Rivet-Pop | 6 |
| 20***03 | Grid | 1 |
| 20***04 | Deflector | 1 |
153-7919 Gasket Gp-Exhaust Manifold
| 15***19 | Gasket Group-Exhaust Manifold | 1 |
| 15***20 | Gasket | 1 |
156-6956 Manifold Gp-Exhaust
| 15***60 | Nut | 2 |
| 15***61 | Bolt | 4 |
| 15***56 | Manifold Group-Exhaust | 1 |
228-7819 Muffler Gp
| 15***47 | Bracket | 2 |
| 16***48 | Plate | 1 |
| 22***19 | Muffler Group | 1 |
228-7817 Muffler Gp
| 15***47 | Bracket | 2 |
| 16***48 | Plate | 1 |
| 22***17 | Muffler Group | 1 |
156-3480 Pipe Gp-Exhaust
| 15***80 | Pipe Group-Exhaust | 1 |
| 26***09 | Clamp-Pipe | 1 |
| 29***18 | Tube As | 1 |
Basic Engine
249-7138 Camshaft Gp
| 15***92 | Key-Woodruff | 1 |
| 15***06 | Spacer | 3 |
| 15***07 | Gear-Camshaft; (22-Teeth) | 1 |
235-5533 Cover Gp-Valve Mechanism
| 15***39 | Gauze; (Crankcase Breather) | 1 |
| 15***62 | Bolt | 2 |
| 15***40 | Bolt | 2 |
235-6967 Crankshaft Gp
| 15***02 | Dowel | 6 |
| 15***18 | Key | 1 |
| 15***19 | Pin | 1 |
241-6858 Cylinder Block Gp
| 15***81 | Plug | 1 |
| 15***82 | Plug | 1 |
| 15***84 | Plug | 4 |
235-6806 Cylinder Block Gp
| 15***87 | Plug | 1 |
| 15***91 | Plug | 1 |
| 15***94 | Dowel | 2 |
235-6978 Cylinder Head Gp
| 15***44 | Stud | 2 |
| 15***88 | Bolt | 11 |
| 15***89 | Bolt | 3 |
235-6974 Cylinder Head Gp
| 15***54 | Seal | 3 |
| 15***56 | Pin-Cotter | 12 |
| 15***57 | Cap | 6 |
161-8262 Flywheel Gp
| 15***69 | Bolt | 1 |
| 15***06 | Bolt | 1 |
| 15***59 | Flywheel As | 1 |
249-7137 Housing Gp-Front
| 15***60 | Nut | 2 |
| 15***62 | Bolt | 3 |
| 15***38 | Bolt | 1 |
154-1877 Lifting Gp-Engine
| 15***75 | Bolt | 2 |
| 15***77 | Lifting Group-Engine | 1 |
| 19***73 | Plate; (Front) | 1 |
228-7752 Mounting Gp-Engine
| 14***53 | Bolt; (M14x1.5x30-mm) | 5 |
| 1V***54 | Mount | 3 |
| 22***52 | Mounting Group-Engine | 1 |
249-7150 Pan Gp-Oil
| 15***33 | Seal; (Engine Oil Filler Cap) | 1 |
| 15***36 | Washer | 4 |
| 15***12 | Washer | 2 |
235-6961 Piston & Rod Gp
| 15***69 | Bushing | 1 |
| 15***70 | Bolt | 2 |
| 15***71 | Nut | 2 |
156-6998 Pulley Gp-Crankshaft
| 15***92 | Nut | 4 |
| 15***92 | Key-Woodruff | 1 |
| 15***94 | Gasket | 1 |
241-6395 Pulley Gp-Water Pump
| 15***22 | Pulley-Water Pump | 1 |
| 16***68 | V-Belt; (Water Pump) | 1 |
| 24***95 | Pulley Group-Water Pump | 1 |
270-6885 Valve Mechanism Gp
| 15***87 | Screw-Adjustment | 6 |
| 15***90 | Nut | 6 |
| 15***61 | Bolt | 2 |
235-6991 Valve Mechanism Gp
| 15***87 | Screw-Adjustment | 6 |
| 15***90 | Nut | 6 |
| 15***61 | Bolt | 2 |
Braking System
228-7785 Lines Gp-Brake
| 11***68 | Hose As | 1 |
| 15***80 | Clamp-Half | 2 |
| 16***85 | Hose As | 1 |
228-7784 Lines Gp-Parking Brake
| 08***37 | Nut | 2 |
| 11***88 | Hose As | 1 |
| 11***75 | Valve-Needle | 1 |
228-7787 Pump Gp-Hand
| 09***41 | Washer; (Hard) (19x34x3 mm Thk) | 1 |
| 14***91 | Steering Wheel As | 1 |
| 14***18 | Connector As | 2 |
Cooling System
156-3486 Fan Gp-Suction
| 15***86 | Fan Group-Suction | 1 |
| 15***60 | Fan-Suction | 1 |
228-7780 Lines Gp-Water
| 08***81 | Tee; (Connection) | 1 |
| 08***96 | End Fitting | 2 |
| 08***40 | Fitting; (Reduction) | 1 |
154-2435 Mounting Gp-Fan
| 15***40 | Bolt | 4 |
| 15***33 | Plate | 1 |
| 15***35 | Mounting Group-Fan | 1 |
311-0053 Pump Gp-Water
| 15***17 | Plug | 1 |
| 15***18 | Plate | 1 |
| 15***20 | Bolt | 3 |
218-2305 Pump Gp-Water
| 15***60 | Nut | 3 |
| 15***61 | Bolt | 4 |
| 15***56 | Bolt | 2 |
228-7750 Radiator Gp
| 08***56 | Suspension Pad | 6 |
| 08***25 | Cap As-Radiator | 1 |
| 15***27 | Hose; (Radiator)(Lower) | 1 |
289-7471 Radiator Gp
| 28***70 | Radiator As | 1 |
| 28***71 | Radiator Group | 1 |
| 29***65 | Cap-Radiator | 1 |
Electrical And Starting System
269-8245 Alternator Gp-Charging
| 10***51 | Bolt; (M8x1.25x130-mm) | 1 |
| 15***92 | Nut | 1 |
| 15***84 | Washer | 1 |
218-2367 Alternator Gp-Charging
| 15***92 | Nut | 2 |
| 15***75 | Bolt | 3 |
| 16***62 | Alternator Group-Charging; -12-Volt | 1 |
269-8246 Alternator Gp-Charging
| 24***98 | Pulley-Alternator | 1 |
| 26***46 | Alternator Group-Charging | 1 |
228-7755 Battery & Wiring Gp
| 13***62 | Cable As-Battery; (Negative) | 1 |
| 15***56 | Battery; (12-Volt, Maintenance Free)(24 V) | 1 |
| 15***63 | Bolt-Hex Head; (M10x1.5x240mm) | 2 |
228-7797 Control Gp-Vibratory -Rear Vibratory
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 15***27 | Hose As | 2 |
| 22***97 | Control Group-Vibratory; -Rear Vibratory | 1 |
228-7727 Electrical Ar
| 22***27 | Electrical Ar | 1 |
| 22***55 | Battery & Wiring Group | 1 |
| 22***58 | Wiring Group-Engine | 1 |
190-3599 Glow Plug Gp
| 15***76 | Nut | 1 |
| 15***77 | Washer | 1 |
| 17***85 | Glow Plug | 3 |
258-7555 Glow Plug Gp
| 15***73 | Support-Plug | 1 |
| 15***76 | Nut | 1 |
| 15***77 | Washer | 1 |
9x-9484 Lamp Gp-Flood -Suspended
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 1 |
| 8T***33 | Nut (M10x1.50 Thd) | 1 |
9x-7779 Lamp Gp-Flood -Roading Lights
| 10***52 | Seal | 1 |
| 10***53 | Lens As; (Floodlight) | 1 |
| 10***54 | Body As; (Lamp) | 1 |
151-2457 Lamp Gp-Head
| 15***57 | Lamp Group-Head; -Floodlight | 1 |
| 17***24 | Lamp; (12-Volt, 55-Watt, Hid)(Warning Beacon Lamp) | 1 |
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
117-8319 Lamp Gp-Registration Plate
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***19 | Lamp Group-Registration Plate; -Eu | 1 |
| 13***49 | Screw-Lens | 2 |
145-2806 Lamp Gp-Registration Plate
| 11***19 | Lamp Group-Registration Plate; -Eu | 1 |
| 13***14 | Lamp; (12-Volt, 5-Watt) | 2 |
| 14***06 | Lamp Group-Registration Plate | 1 |
256-0042 Lamp Gp-Registration Plate
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***05 | Lamp; (12-Volt, 5-Watt)(Registration Plate) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
118-1227 Lamp Gp-Warning Beacon
| 11***27 | Lamp Group-Warning Beacon | 1 |
| 11***32 | Clip Bulb-Securing | 1 |
| 11***33 | Lens-Amber; (Warning Beacon Lamp) | 1 |
228-7815 Lighting Gp-Flood
| 22***15 | Lighting Group-Flood | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
| 3T***51 | Locknut; (M5x0.8-Thd) | 2 |
289-2425 Lighting Gp-Roading
| 28***28 | Lighting Group-Roading | 1 |
| 28***29 | Mirror Group-Rear View | 1 |
| 28***25 | Lighting Group-Roading | 1 |
248-4043 Lighting Gp-Roading -Italian Roading
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 11***18 | Clip | 1 |
| 22***59 | Reflector; (Red) | 2 |
228-7814 Lighting Gp-Roading
| 10***05 | Lamp; (12-Volt, 5-Watt)(Registration Plate) | 4 |
| 11***50 | Lamp; (Front, Rh)(Running/Turn Signal) | 1 |
| 11***24 | Lamp; (Front, Lh)(Running/Turn Signal) | 1 |
289-0328 Lighting Gp-Roading
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 8 |
| 11***18 | Clip | 1 |
| 22***59 | Reflector; (Red) | 2 |
156-3572 Lighting Gp-Warning Beacon
| 08***97 | Support | 1 |
| 15***72 | Lighting Group-Warning Beacon | 1 |
| 29***46 | Lamp Group; (Basic)(Amber) | 1 |
172-2167 Lighting Gp-Warning Beacon
| 08***97 | Support | 1 |
| 11***27 | Lamp Group-Warning Beacon | 1 |
| 17***67 | Lighting Group-Warning Beacon | 1 |
238-3235 Module Gp-Timer -Vibratory
| 23***73 | Relay-Time Delay | 1 |
| 23***35 | Module Group-Timer; -Vibratory | 1 |
217-5795 Sensor Gp-Temp & Press
| 15***36 | Washer | 2 |
| 18***65 | Plug | 1 |
| 21***93 | Switch-Temperature; (Engine Coolant) | 1 |
339-2904 Starting Motor Gp-Electric
| 17***44 | Switch Group-Magnetic | 1 |
| 17***45 | Switch Group-Magnetic | 1 |
| 33***04 | Starting Motor Group-Electric | 1 |
176-7720 Starting Motor Gp-Electric
| 14***83 | Bolt; (M10x1.5x45-mm)(Starter Motor) | 2 |
| 17***20 | Starting Motor Group-Electric | 1 |
| 33***03 | Kit-Terminal | 1 |
339-2900 Starting Motor Gp-Electric
| 33***00 | Starting Motor Group-Electric | 2 |
163-3361 Starting Motor Gp-Electric
| 15***99 | Washer | 2 |
| 15***01 | Bolt | 2 |
| 15***03 | Washer | 2 |
117-9080 Switch Gp-Magnetic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***80 | Switch Group-Magnetic; (Start Relay) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
175-2344 Switch Gp-Magnetic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***44 | Switch Group-Magnetic | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
175-2345 Switch Gp-Magnetic
| 15***36 | Washer | 2 |
| 17***45 | Switch Group-Magnetic | 1 |
| 18***65 | Plug | 1 |
291-1260 Switch Gp-Press & Temp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***18 | Clip | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
231-3334 Warning Gp-Backup
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***96 | Timer; (Water Spray) | 1 |
228-7813 Wiring Gp-Console
| 22***13 | Wiring Group-Console | 1 |
| 23***10 | Harness As-Engine | 1 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 1 |
228-7758 Wiring Gp-Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***80 | Switch Group-Magnetic; (Start Relay) | 2 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
228-7759 Wiring Gp-Machine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***80 | Switch Group-Magnetic; (Start Relay) | 2 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
Engine Arrangement
226-8699 Engine Ar-Primary
| 15***19 | Gasket Group-Exhaust Manifold | 1 |
| 15***77 | Lifting Group-Engine | 1 |
| 15***35 | Mounting Group-Fan | 1 |
228-7725 Installation Ar-Engine
| 15***74 | Air Cleaner Group | 1 |
| 15***80 | Pipe Group-Exhaust | 1 |
| 15***84 | Mounting Group-Pump | 1 |
Frame And Body
248-4042 Conversion Gp-Roading -Italian Roading
| 07***27 | Screw-Drive; (No.12x12.7-mm) | 2 |
| 08***14 | Edging; (.4-M Each) | 0 |
| 08***86 | Edging; (0.13-M Each) | 0 |
228-7765 Frame Gp-Front
| 08***14 | Edging; (.4-M Each) | 0 |
| 16***30 | Seal; (10-cm Each) | 0 |
| 22***65 | Frame Group-Front | 1 |
228-7767 Frame Gp-Rear
| 16***30 | Seal; (10-cm Each) | 0 |
| 17***17 | Plate; (Lift) | 2 |
| 22***67 | Frame Group-Rear | 1 |
230-3876 Frame Gp-Rear
| 16***12 | Protector As | 2 |
| 23***76 | Frame Group-Rear | 1 |
| 5C***53 | Bolt (M6x1.00x16mm); (M6x1x16mm Thk) | 16 |
277-6721 Guard Gp-Lighting
| 23***95 | Film-Warning; (Foot Crushing Hazard) | 2 |
| 27***21 | Guard Group-Lighting | 1 |
| 28***90 | Plate; (Rh) | 1 |
151-1182 Guard Gp-Lighting
| 15***82 | Guard Group-Lighting | 1 |
| 27***22 | Protector | 4 |
| 8T***38 | Bolt-Plt; (M6 X 1.0 X 20) | 16 |
280-9193 Guard Gp-Platform
| 24***13 | Guard As; (Rh Front, Lh Rear) | 2 |
| 24***14 | Guard As; (Lh Front, Rh Rear) | 2 |
| 28***93 | Guard Group-Platform | 1 |
242-9766 Guard Gp-Spray Bar -Spray Bar Windshield
| 08***20 | Axle | 1 |
| 08***47 | Seal | 1 |
| 08***19 | Bearing; (Small) | 1 |
215-6192 Hitch Gp-Oscillating
| 08***24 | Handle | 1 |
| 16***17 | Plate As | 2 |
| 18***32 | Seal; (2.48-M) | 0 |
228-7771 Hood Gp
| 15***10 | Grill-Radiator | 1 |
| 17***05 | Rivet-Pop | 9 |
| 22***71 | Hood Group | 1 |
230-1187 Hood Gp
| 14***34 | Scraper As-Bottom | 2 |
| 15***59 | Eyebolt; (M8x1.25x100-mm) | 2 |
| 16***59 | Plate As | 1 |
156-3511 Scraper Gp-Smooth Drum
| 09***49 | Bolt; (M8x1.25x40-mm) | 8 |
| 14***18 | Plate | 4 |
| 15***27 | Plate As | 1 |
156-3510 Scraper Gp-Smooth Drum
| 14***35 | Scraper As-Drum | 2 |
| 15***10 | Scraper Group-Smooth Drum | 1 |
| 15***59 | Eyebolt; (M8x1.25x100-mm) | 2 |
228-7825 Scraper Gp-Tire
| 08***98 | Ring | 14 |
| 08***54 | Link | 2 |
| 17***69 | Skirt | 1 |
156-3508 Scraper Gp-Tire
| 09***12 | Spring | 2 |
| 14***18 | Plate | 4 |
| 15***08 | Scraper Group-Tire | 1 |
245-3988 Skirt Gp-Tire
| 23***83 | Guard As; (Lh) | 1 |
| 23***84 | Guard As; (Rh) | 1 |
| 24***88 | Skirt Group-Tire | 1 |
236-6982 Step Gp
| 08***37 | Nut | 2 |
| 10***08 | Hose As | 1 |
| 11***88 | Hose As | 1 |
Fuel System
228-7812 Control Gp-Governor
| 16***23 | Bracket | 1 |
| 22***12 | Control Group-Governor | 1 |
| 25***53 | Control Group-Governor | 1 |
228-7783 Control Gp-Governor
| 12***10 | Bellows | 1 |
| 17***14 | Handle Group-Control | 1 |
| 19***07 | Ball Joint | 1 |
251-9953 Control Gp-Governor
| 24***02 | Bellows | 1 |
| 24***05 | Ball Joint | 1 |
| 24***07 | Control Group-Acceleration | 1 |
144-9962 Filter Gp-Water Sep & Fuel
| 11***01 | Bowl As-Water Collection | 1 |
| 11***18 | Ring-Retaining | 1 |
| 11***19 | Nut | 1 |
297-3091 Fitting Gp-Fuel Lines
| 13***11 | Cap; (Tamper Resistant) | 1 |
| 15***60 | Nut | 1 |
| 15***83 | Pin | 1 |
249-7149 Governor Gp
| 15***75 | Connector | 2 |
| 17***54 | Pump Group-Fuel Prm & Prim Filter; -Water Separator | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 4 |
228-7753 Lines Gp-Fuel
| 15***73 | Bolt | 2 |
| 22***53 | Lines Group-Fuel | 1 |
| 29***70 | Pump As-Fuel Transfer | 1 |
176-7711 Pump & Mtg Gp-Fuel Transfer
| 15***92 | Nut | 2 |
| 15***60 | Nut | 2 |
| 15***12 | Washer | 1 |
275-2033 Pump Gp-Fuel Injection
| 20***26 | Bolt-Special; (Banjo) | 1 |
| 20***27 | Washer | 2 |
| 20***28 | Connector | 1 |
235-5526 Pump Gp-Fuel Injection
| 15***60 | Nut | 1 |
| 15***15 | Washer | 3 |
| 15***16 | Seal | 3 |
176-9954 Pump Gp-Fuel Prm & Prim Filter
| 12***59 | Pump Group-Fuel Priming | 1 |
| 12***62 | Bladder | 1 |
| 14***62 | Filter Group-Water Sep & Fuel | 1 |
228-7770 Tank & Mtg Gp-Fuel
| 13***40 | Locknut; (M8x1.25-Thd) | 2 |
| 17***80 | Edging | 0 |
| 22***70 | Tank & Mtg Group-Fuel | 1 |
229-2824 Tank Gp-Fuel
| 15***28 | Cap; (Fuel, Vented)(Fuel Tank) | 1 |
| 17***41 | Strainer; (Water Tank) | 1 |
| 17***50 | Plug | 1 |
Hydraulic System
228-7811 Control Gp-Hydraulic
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 1G***04 | Control Group-Handle | 1 |
229-3768 Control Gp-Hydraulic
| 15***03 | Cooler Group-Hydraulic Oil | 1 |
| 16***70 | Plate | 1 |
| 22***68 | Control Group-Hydraulic | 1 |
156-1502 Cooler & Mtg Gp-Hydraulic Oil
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***02 | Cooler & Mtg Group-Hydraulic Oil | 1 |
| 17***48 | Motor As-Fan | 1 |
156-1503 Cooler Gp-Hydraulic Oil
| 08***76 | Fitting-Grease | 1 |
| 08***45 | Fitting-Grease | 1 |
| 11***23 | Kit-Seals; (Hydraulic Steering Cylinder) | 1 |
154-6938 Cylinder Gp-Hydraulic
| 15***38 | Cylinder Group-Hydraulic | 1 |
| 22***20 | Filter Group-Oil; -Hydraulic | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 2 |
228-7804 Filter & Mtg Gp-Hydraulic
| 14***91 | Filter-Oil; (Advanced Efficiency) | 1 |
| 22***04 | Filter & Mtg Group-Hydraulic | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
222-6420 Filter Gp-Oil -Hydraulic
| 15***49 | Cylinder & Mtg Group-Steering | 1 |
| 15***54 | Pump & Mtg Group-Hydraulic | 1 |
| 22***20 | Filter Group-Oil; -Hydraulic | 1 |
228-7745 Hydraulic Ar-Auxiliary
| 1P***78 | Clamp; (Hose) | 1 |
| 22***45 | Hydraulic Ar-Auxiliary | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
175-0267 Lines Gp-Drain
| 14***01 | Hose As | 1 |
| 17***67 | Lines Group-Drain | 1 |
| 1G***40 | Hose As | 1 |
228-7803 Lines Gp-Filter
| 11***24 | Hose As | 1 |
| 11***27 | Hose As | 2 |
| 1G***61 | Hose As | 1 |
240-5719 Lines Gp-Pilot
| 12***88 | Kit-Seal; (Gear-Motor) | 1 |
| 17***64 | Key-Square | 1 |
| 24***19 | Lines Group-Pilot | 1 |
156-9037 Motor Gp-Gear
| 14***88 | Bearing Group-Self-Aligning | 1 |
| 14***89 | Spacer | 1 |
| 14***90 | Ring-Split | 1 |
131-3118 Motor Gp-Hydraulic -Propel
| 13***18 | Motor Group-Hydraulic; -Propel | 1 |
| 18***38 | Kit-Seal; (Propel Piston Motor) | 1 |
| 19***64 | Kit-Seal; (Propel Piston Motor) | 1 |
245-3602 Motor Gp-Piston
| 16***30 | Film-Identification; (Biodegradable Hydraulic Oil) | 1 |
| 18***38 | Kit-Seal; (Propel Piston Motor) | 1 |
| 19***64 | Kit-Seal; (Propel Piston Motor) | 1 |
304-5602 Motor Gp-Piston
| 15***39 | Pump Group-Gear | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 30***02 | Motor Group-Piston | 1 |
156-3554 Pump & Mtg Gp-Hydraulic
| 15***54 | Pump & Mtg Group-Hydraulic | 1 |
| 17***22 | Nut | 1 |
| 17***30 | Key-Square | 1 |
156-9036 Pump Gp-Gear
| 08***17 | Seal-O-Ring | 1 |
| 15***36 | Pump Group-Gear | 1 |
| 18***77 | Kit-Seal; (Gear Pump) | 1 |
156-9039 Pump Gp-Gear
| 15***39 | Pump Group-Gear | 1 |
| 24***47 | Kit-Pump Shaft; (Propel Pump) | 1 |
| 24***48 | Kit-Housing; (Propel Pump) | 1 |
245-3215 Pump Gp-Piston -Propel
| 24***15 | Pump Group-Piston; -Propel | 1 |
| 24***47 | Kit-Pump Shaft; (Propel Pump) | 1 |
| 24***49 | Kit-Swashplate; (Propel Pump) | 1 |
229-3753 Pump Gp-Piston -Propel
| 22***53 | Pump Group-Piston; -Propel | 1 |
| 24***46 | Plate-Valve | 1 |
| 24***47 | Kit-Pump Shaft; (Propel Pump) | 1 |
296-1553 Pump Gp-Piston
| 13***65 | Gasket | 1 |
| 13***36 | Screen; (Water Strainer) | 1 |
| 25***55 | Washer; (14.5x18x1.5-mm Thk) | 1 |
229-3752 Pump Gp-Piston -Propel
| 22***52 | Pump Group-Piston; -Propel | 1 |
| 24***47 | Kit-Pump Shaft; (Propel Pump) | 1 |
| 24***48 | Kit-Housing; (Propel Pump) | 1 |
293-8612 Strainer Gp
| 08***14 | Breather; (Hydraulic Oil Tank) | 1 |
| 08***14 | Seal; (.82m) | 0 |
| 15***46 | Tank As-Hydraulic | 1 |
151-4745 Tank Gp-Hydraulic
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 1 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 3 |
| 15***45 | Tank Group-Hydraulic | 1 |
228-7794 Valve & Mtg Gp-Control
| 14***25 | Hose As | 1 |
| 14***04 | Hose As | 1 |
| 16***65 | Hose As | 1 |
228-7749 Valve & Mtg Gp-Control
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 3 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 3 |
245-4519 Valve Gp-Flow Divider
| 09***79 | Setscrew-Socket | 2 |
| 09***94 | Pin-Spring | 1 |
| 15***54 | Shaft As-Drive | 1 |
228-7836 Valve Gp-Flow Divider
| 20***39 | Kit-Seal; (Flow Divider Valve) | 1 |
| 20***40 | Valve-Relief | 2 |
| 20***41 | Kit-Seal; (Relief Valve) | 2 |
Lubrication System
249-7157 Filter Gp-Engine Oil
| 15***79 | Stud-Hollow | 1 |
| 22***23 | Filter As-Engine Oil | 1 |
| 24***57 | Filter Group-Engine Oil | 1 |
Machine Arrangement
228-7734 Chassis Ar
| 15***45 | Tank Group-Hydraulic | 1 |
| 15***02 | Cooler & Mtg Group-Hydraulic Oil | 1 |
| 15***11 | Scraper Group-Smooth Drum | 1 |
228-7733 Chassis Ar
| 15***45 | Tank Group-Hydraulic | 1 |
| 15***02 | Cooler & Mtg Group-Hydraulic Oil | 1 |
| 15***11 | Scraper Group-Smooth Drum | 2 |
228-7732 Chassis Ar
| 15***45 | Tank Group-Hydraulic | 1 |
| 15***02 | Cooler & Mtg Group-Hydraulic Oil | 1 |
| 15***10 | Scraper Group-Smooth Drum | 2 |
228-7721 Common Ar
| 22***99 | Engine Ar-Primary | 1 |
| 22***21 | Common Ar | 1 |
| 22***25 | Installation Ar-Engine | 1 |
228-7723 Common Ar
| 22***99 | Engine Ar-Primary | 1 |
| 22***23 | Common Ar | 1 |
| 22***25 | Installation Ar-Engine | 1 |
228-7722 Common Ar
| 22***99 | Engine Ar-Primary | 1 |
| 22***22 | Common Ar | 1 |
| 22***25 | Installation Ar-Engine | 1 |
Operator Station
215-6191 Bearing Gp-Self-Aligning
| 14***69 | Plate | 2 |
| 14***39 | Plug | 4 |
| 17***11 | Canopy | 1 |
156-3568 Canopy Gp
| 14***69 | Plate | 2 |
| 15***68 | Canopy Group | 1 |
| 17***11 | Canopy | 1 |
279-9103 Canopy Gp
| 10***16 | Screw; (4-40x15.88-mm) | 4 |
| 10***19 | Switch-Push Button; (Vibratory Select On/Off) | 1 |
| 10***21 | Cap | 1 |
1g-4704 Control Gp-Handle
| 1G***04 | Control Group-Handle | 1 |
| 22***04 | Cover | 1 |
| 24***28 | Spacer | 2 |
230-2066 Guard Gp-Vandalism
| 13***82 | Arm-Mirror | 2 |
| 13***83 | Mirror-Convex | 2 |
| 23***66 | Guard Group-Vandalism | 1 |
248-4044 Mirror Gp-Rear View -Italian Roading
| 13***82 | Arm-Mirror | 2 |
| 13***83 | Mirror-Convex | 2 |
| 24***44 | Mirror Group-Rear View; -Italian Roading | 1 |
289-0329 Mirror Gp-Rear View
| 24***10 | Ring | 1 |
| 24***15 | Lamp As; (12-Volt, 3-Watt)(Alternator) | 1 |
| 24***20 | Lamp As; (12-Volt, 1-Watt) | 10 |
230-7848 Module Gp-Display
| 22***09 | Platform Group-Operator | 1 |
| 22***10 | Control Group-Steering | 1 |
| 22***11 | Control Group-Hydraulic | 1 |
230-3902 Operator Ar
| 11***26 | Mount | 4 |
| 15***42 | Plate | 1 |
| 18***34 | Seal; (0.64-M) | 0 |
228-7747 Operator Ar
| 22***47 | Operator Ar | 1 |
| 22***10 | Control Group-Steering | 1 |
| 22***11 | Control Group-Hydraulic | 1 |
230-3877 Platform Gp-Operator
| 08***06 | Piston, Mount-Resilient | 2 |
| 13***79 | Grommet | 3 |
| 19***28 | Rops As | 1 |
228-7809 Platform Gp-Operator
| 08***07 | Stud | 3 |
| 08***35 | Chain | 3 |
| 08***17 | Rivet | 6 |
194-7622 Rops Gp
| 15***86 | Shim; (2-mm Thk) | 2 |
| 19***22 | Rops Group | 1 |
| 21***05 | Film; (Warning) (No Weld/ No Drill) (Rearward Of Rh Cab Door) | 1 |
245-2719 Rops Gp -Foldable
| 08***86 | Edging; (0.13-M Each) | 0 |
| 10***82 | Bolt-Socket Head; (M8x1.25x16-mm) | 4 |
| 10***29 | Seat Belt Group | 1 |
245-2718 Rops Gp
| 07***27 | Screw-Drive; (No.12x12.7-mm) | 4 |
| 15***86 | Shim; (2-mm Thk) | 2 |
| 19***22 | Rops Group | 1 |
245-2717 Rops Gp
| 15***86 | Shim; (2-mm Thk) | 2 |
| 15***80 | Rops As | 1 |
| 21***05 | Film; (Warning) (No Weld/ No Drill) (Rearward Of Rh Cab Door) | 1 |
228-7833 Seat Gp -Switch
| 22***30 | Seat Group-Adjustable; -Vinyl | 1 |
| 22***33 | Seat Group; -Switch | 1 |
| 23***90 | Valve Group-Solenoid; -Hydraulic Lockout | 1 |
244-8343 Seat Gp
| 15***09 | Kit-Cover; (Adjustable Seat) | 1 |
| 15***10 | Kit-Stop; (Adjustable Seat) | 1 |
| 15***15 | Kit-Damper; (Adjustable Seat) | 1 |
228-7831 Seat Gp -No Slide
| 08***86 | Edging; (0.13-M Each) | 0 |
| 10***82 | Bolt-Socket Head; (M8x1.25x16-mm) | 4 |
| 10***29 | Seat Belt Group | 1 |
228-7832 Seat Gp -Sliding
| 22***30 | Seat Group-Adjustable; -Vinyl | 1 |
| 22***32 | Seat Group; -Sliding | 1 |
| 23***90 | Valve Group-Solenoid; -Hydraulic Lockout | 1 |
228-7830 Seat Gp-Adjustable -Vinyl
| 22***13 | Film; (Warning) (Jump Start) (Inside Of Lh Battery Box Cover) | 1 |
| 22***05 | Film; (Warning) (Universal) (On Lh Post Inside Cab) | 1 |
| 22***56 | Film; (Warning) (Hot Fluid) (Underside Of Door To Radiator Fill) | 1 |
Power Train
228-7821 Drum Gp-Compactor
| 1G***84 | Stud | 8 |
| 22***21 | Drum Group-Compactor | 1 |
| 23***79 | Plate-Propel | 1 |
228-7820 Drum Gp-Compactor
| 1G***84 | Stud | 8 |
| 22***20 | Drum Group-Compactor | 1 |
| 23***79 | Plate-Propel | 1 |
242-1728 Drum Gp-Smooth
| 22***84 | Drum Group-Smooth | 2 |
| 24***28 | Drum Group-Smooth | 1 |
| 24***14 | Pump & Mtg Group-Propel | 1 |
242-1729 Drum Gp-Smooth
| 15***38 | Motor & Mtg Group-Propel | 2 |
| 22***84 | Lines Group-Parking Brake | 1 |
| 22***88 | Lines Group-Propel | 1 |
226-7384 Drum Gp-Smooth
| 22***84 | Drum Group-Smooth | 1 |
| 22***20 | Drum Group-Compactor | 2 |
242-1726 Drum Gp-Smooth
| 22***90 | Pump & Mtg Group-Propel | 1 |
| 24***26 | Drum Group-Smooth | 1 |
242-1727 Drum Gp-Smooth
| 22***21 | Drum Group-Compactor | 1 |
| 24***27 | Drum Group-Smooth | 1 |
228-7739 Hydraulic Ar-Propel
| 15***38 | Motor & Mtg Group-Propel | 1 |
| 15***39 | Motor & Mtg Group-Propel | 1 |
| 22***39 | Hydraulic Ar-Propel | 1 |
228-7741 Hydraulic Ar-Propel
| 15***38 | Motor & Mtg Group-Propel | 2 |
| 22***41 | Hydraulic Ar-Propel | 1 |
| 22***84 | Lines Group-Parking Brake | 1 |
245-3213 Hydraulic Ar-Propel
| 10***05 | Plate | 3 |
| 10***88 | Hose As | 1 |
| 11***50 | Clamp | 3 |
228-7788 Lines Gp-Propel
| 08***14 | Seal; (.82m) | 1 |
| 10***05 | Plate | 2 |
| 10***88 | Hose As | 1 |
228-7789 Lines Gp-Propel
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 22***89 | Lines Group-Propel | 1 |
156-3538 Motor & Mtg Gp-Propel
| 13***18 | Motor Group-Hydraulic; -Propel | 2 |
| 15***38 | Motor & Mtg Group-Propel | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 4 |
156-3539 Motor & Mtg Gp-Propel
| 10***78 | Bolt; (Socket Head) (M10x1.5x35mm) | 5 |
| 14***61 | Hub As-Coupling | 1 |
| 14***62 | Flange-Nylon | 1 |
156-3484 Mounting Gp-Pump
| 15***84 | Mounting Group-Pump | 1 |
| 15***94 | Housing Group-Eccentric Weight | 2 |
| 22***63 | Support Group-Vibratory | 2 |
228-7729 Power Train Ar
| 15***95 | Housing Group-Eccentric Weight | 2 |
| 22***29 | Power Train Ar | 1 |
| 22***64 | Support Group-Vibratory | 2 |
228-7731 Power Train Ar
| 22***31 | Power Train Ar | 1 |
| 22***52 | Pump Group-Piston; -Propel | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 4 |
228-7730 Power Train Ar
| 15***95 | Housing Group-Eccentric Weight | 1 |
| 22***30 | Power Train Ar | 1 |
| 22***64 | Support Group-Vibratory | 1 |
245-3214 Pump & Mtg Gp-Propel
| 24***14 | Pump & Mtg Group-Propel | 1 |
| 29***53 | Pump Group-Piston | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 4 |
228-7790 Pump & Mtg Gp-Propel
| 22***90 | Pump & Mtg Group-Propel | 1 |
| 22***53 | Pump Group-Piston; -Propel | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 4 |
228-7791 Pump & Mtg Gp-Propel
| 22***91 | Pump & Mtg Group-Propel | 1 |
| 24***15 | Pump Group-Piston; -Propel | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 4 |
236-8036 Support Gp-Motor -Propel
| 10***69 | Bolt-Head; (M8x1.25x50-mm) | 2 |
| 15***29 | Shim; (2-mm Thk) | 1 |
| 15***30 | Shim; (1-mm Thk) | 1 |
236-8037 Support Gp-Motor -Propel
| 15***01 | Wheel & Tire Group | 1 |
| 15***08 | Scraper Group-Tire | 1 |
| 23***37 | Support Group-Motor; -Propel | 1 |
228-7776 Tire Gp
| 22***12 | Wheel & Tire Group | 1 |
| 22***76 | Tire Group | 1 |
| 22***25 | Scraper Group-Tire | 1 |
228-7777 Tire Gp
| 14***43 | Rim; (15x7-In) | 1 |
| 14***48 | Tire Group; (9.5/65-15 6pr) | 1 |
| 14***49 | Tube | 1 |
238-3327 Wheel & Tire Gp
| 23***27 | Wheel & Tire Group | 1 |
| 24***43 | Lighting Group-Roading; -Italian Roading | 1 |
| 24***44 | Mirror Group-Rear View; -Italian Roading | 1 |
238-3326 Wheel & Tire Gp
| 16***44 | Valve-Tire | 1 |
| 23***00 | Rim | 1 |
| 23***26 | Wheel & Tire Group | 1 |
225-4412 Wheel & Tire Gp
| 16***44 | Valve-Tire | 1 |
| 22***12 | Wheel & Tire Group | 1 |
| 23***99 | Rim | 1 |
156-3501 Wheel & Tire Gp
| 15***01 | Wheel & Tire Group | 1 |
| 23***26 | Wheel & Tire Group | 2 |
| 23***27 | Wheel & Tire Group | 2 |
143-2747 Wheel & Tire Gp -Smooth
| 14***46 | Wheel & Tire Group; -Smooth | 2 |
| 14***47 | Wheel & Tire Group; -Smooth | 3 |
143-2746 Wheel & Tire Gp -Smooth
| 14***44 | Rim; (15x7-In) | 1 |
| 14***46 | Wheel & Tire Group; -Smooth | 1 |
| 14***48 | Tire Group; (9.5/65-15 6pr) | 1 |
Service Equipment And Supplies
301-0318 Film Gp
| 13***39 | Film-Stripe; (Red)(625cm) | 0 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 15***64 | Film; (Instruction) (Hydraulic Oil) (On Forward Of And Above The Hydraulic Tank Sight Gage On Tank Surface) | 1 |
301-0309 Film Gp
| 30***09 | Film Group | 1 |
| 30***10 | Film-Identification; (Cb224e, Lh) | 1 |
| 30***11 | Film-Identification; (Cb224e, Rh) | 1 |
252-0310 Film Gp
| 22***54 | Film-Warning; (Universal, Read Omm, Intl) | 1 |
| 22***12 | Film; (Warning) (Jump Start) (On Outside Of Battery Compartment Door) | 1 |
| 22***57 | Film; (Warning) (Hot Fluid) (Next To Radiator Fill Cap) (On Forward Face Of Hydraulic Tank Above Filler Neck) | 1 |
301-0312 Film Gp
| 30***12 | Film Group | 1 |
| 30***16 | Film-Identification; (Cat, Cb225e, Lh) | 1 |
| 30***17 | Film-Identification; (Cat, Cb225e, Rh) | 1 |
252-0311 Film Gp
| 25***11 | Film Group | 1 |
| 30***07 | Film-Identification; (Cat, Cb214e, Lh) | 1 |
| 30***08 | Film-Identification; (Cat, Cb214e, Rh) | 1 |
257-3886 Plate & Film Gp
| 25***86 | Plate & Film Group | 1 |
229-1170 Plate & Film Gp
| 13***39 | Film-Stripe; (Red)(625cm) | 0 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 15***64 | Film; (Instruction) (Hydraulic Oil) (On Forward Of And Above The Hydraulic Tank Sight Gage On Tank Surface) | 1 |
229-1169 Plate & Film Gp
| 13***39 | Film-Stripe; (Red)(625cm) | 0 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 15***64 | Film; (Instruction) (Hydraulic Oil) (On Forward Of And Above The Hydraulic Tank Sight Gage On Tank Surface) | 1 |
229-1171 Plate & Film Gp
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 15***64 | Film; (Instruction) (Hydraulic Oil) (On Forward Of And Above The Hydraulic Tank Sight Gage On Tank Surface) | 1 |
| 15***97 | Film-Identification; (Water For Water Spray) | 1 |
Steering System
228-7810 Control Gp-Steering
| 08***30 | Washer | 4 |
| 15***38 | Cylinder Group-Hydraulic | 1 |
| 15***94 | Axle As; (Cylinder Steering) | 2 |
156-3549 Cylinder & Mtg Gp-Steering
| 15***49 | Cylinder & Mtg Group-Steering | 1 |
| 16***43 | Hose As | 1 |
| 16***44 | Hose As | 1 |
228-7802 Lines Gp-Steering
| 17***50 | Kit-Seal; (Metering Pump) | 1 |
| 22***02 | Lines Group-Steering | 1 |
156-1509 Pump Gp-Metering
| 10***82 | Bolt-Socket Head; (M8x1.25x16-mm) | 2 |
| 15***09 | Pump Group-Metering | 1 |
| 22***68 | Control Group-Hydraulic | 1 |
Vibratory System
156-3495 Housing Gp-Eccentric Weight
| 15***95 | Housing Group-Eccentric Weight | 1 |
| 15***47 | Motor & Mtg Group-Vibratory | 2 |
| 22***94 | Valve & Mtg Group-Control | 1 |
156-3494 Housing Gp-Eccentric Weight
| 09***79 | Setscrew-Socket | 2 |
| 09***94 | Pin-Spring | 1 |
| 15***94 | Housing Group-Eccentric Weight | 1 |
228-7742 Hydraulic Ar-Vibratory
| 15***47 | Motor & Mtg Group-Vibratory | 1 |
| 22***42 | Hydraulic Ar-Vibratory | 1 |
| 22***49 | Valve & Mtg Group-Control | 1 |
228-7744 Hydraulic Ar-Vibratory
| 10***21 | Hose As | 1 |
| 10***05 | Plate | 3 |
| 12***19 | Hose As | 1 |
228-7799 Lines Gp-Vibratory
| 14***16 | Connector Group | 1 |
| 14***72 | Elbow Group | 2 |
| 15***37 | Motor Group-Gear; -Vibratory | 1 |
228-7798 Lines Gp-Vibratory
| 10***21 | Hose As | 1 |
| 10***05 | Plate | 1 |
| 12***19 | Hose As | 1 |
156-3547 Motor & Mtg Gp-Vibratory
| 15***47 | Motor & Mtg Group-Vibratory | 1 |
| 15***54 | Pulley; (Large) | 1 |
| 15***55 | Pulley; (Small) | 1 |
247-7958 Pump & Mtg Gp-Vibratory
| 15***54 | Pulley; (Large) | 1 |
| 15***55 | Pulley; (Small) | 1 |
| 15***32 | V-Belt; (Vibratory Gear Pump) | 2 |
228-7764 Support Gp-Vibratory
| 22***69 | Valve Group-Solenoid; (Flow Control) | 2 |
| 22***70 | Valve Group-Counterbalance | 1 |
| 22***64 | Support Group-Vibratory | 1 |
228-7763 Support Gp-Vibratory
| 10***06 | Ring-Seal | 2 |
| 10***69 | Bolt-Head; (M8x1.25x50-mm) | 2 |
| 15***29 | Shim; (2-mm Thk) | 1 |
227-3967 Valve Gp-Vibratory
| 08***92 | Pin | 2 |
| 10***46 | Seal-Lip Type | 2 |
| 10***24 | Bushing | 1 |
1g-7186 Weight Gp-Eccentric
| 08***92 | Pin | 2 |
| 10***46 | Seal-Lip Type | 2 |
| 11***00 | Spacer; (41.5x46.5x5-mm Thk) | 1 |
1g-7613 Weight Gp-Eccentric
| 08***48 | Nozzle | 4 |
| 08***63 | Cap | 5 |
| 08***65 | Seal | 7 |
Water System
249-3051 Bar Gp-Spray
| 24***48 | Pipe Group-Spray Extension | 1 |
| 24***51 | Bar Group-Spray | 1 |
| 7R***08 | Clamp | 4 |
249-3049 Bar Gp-Spray
| 24***49 | Bar Group-Spray | 2 |
| 7R***08 | Clamp | 4 |
| 7V***28 | Plate | 2 |
249-3054 Bar Gp-Spray
| 08***95 | Elbow | 2 |
| 16***21 | Strainer Group-Water | 1 |
| 24***54 | Bar Group-Spray | 1 |
228-7781 Filter Gp-Water
| 08***95 | Elbow | 3 |
| 08***54 | Fitting | 1 |
| 16***21 | Strainer Group-Water | 2 |
228-7782 Filter Gp-Water
| 15***86 | Hose; (0.06m)(2 Each) | 0 |
| 22***82 | Filter Group-Water | 1 |
| 23***84 | Valve Group-Control | 1 |
228-7828 Lines Gp-Water Spray
| 15***86 | Hose; (0.06m)(2 Each) | 0 |
| 22***28 | Lines Group-Water Spray | 1 |
| 23***84 | Valve Group-Control | 1 |
228-7829 Lines Gp-Water Spray
| 17***13 | Mat & Mtg Group-Water | 2 |
| 22***29 | Lines Group-Water Spray | 1 |
| 5C***90 | Nut; (M6x1-Thd)(Air Inlet Heater) | 8 |
156-3571 Mat & Mtg Gp-Water
| 15***71 | Mat & Mtg Group-Water | 1 |
| 17***12 | Mat & Mtg Group-Water | 2 |
173-4203 Mat & Mtg Gp-Water
| 17***03 | Mat & Mtg Group-Water | 1 |
| 17***12 | Mat & Mtg Group-Water | 1 |
173-4204 Mat & Mtg Gp-Water
| 08***62 | Rivet | 12 |
| 11***41 | Plate | 1 |
| 11***43 | Mat-Water | 1 |
175-4112 Mat & Mtg Gp-Water
| 08***62 | Rivet | 12 |
| 11***42 | Mat-Water | 1 |
| 17***11 | Clip | 3 |
175-4113 Mat & Mtg Gp-Water
| 08***48 | Nozzle | 4 |
| 08***63 | Cap | 5 |
| 08***78 | Sprayer Clamp | 5 |
249-3048 Pipe Gp-Spray Extension
| 16***60 | Head-Pump | 1 |
| 16***63 | Motor-Electric; (12-Volt) | 1 |
| 24***48 | Pipe Group-Spray Extension | 1 |
235-7846 Pump Gp-Diaphragm -Water Spray
| 16***63 | Motor-Electric; (12-Volt) | 1 |
| 23***46 | Pump Group-Diaphragm; -Water Spray | 1 |
| 24***23 | Head-Pump | 1 |
247-6742 Pump Gp-Diaphragm -Water Spray
| 08***31 | Elbow | 3 |
| 08***81 | Tee; (Connection) | 1 |
| 08***96 | End Fitting | 1 |
146-8045 Pump Gp-Diaphragm -Water Spray
| 14***45 | Pump Group-Diaphragm; -Water Spray-Additive Spray | 1 |
228-7779 Pump Gp-Water Spray
| 08***31 | Elbow | 3 |
| 08***81 | Tee; (Connection) | 1 |
| 08***96 | End Fitting | 1 |
229-0651 Pump Gp-Water Spray
| 08***31 | Elbow | 1 |
| 08***96 | End Fitting | 1 |
| 22***51 | Pump Group-Water Spray | 1 |
228-7735 Spray Ar-Water
| 22***35 | Spray Ar-Water | 1 |
| 22***81 | Filter Group-Water | 1 |
| 22***51 | Pump Group-Water Spray | 1 |
228-7736 Spray Ar-Water
| 22***36 | Spray Ar-Water | 1 |
| 22***78 | Tank Group-Water | 1 |
| 22***79 | Pump Group-Water Spray | 1 |
228-7737 Spray Ar-Water
| 13***65 | Gasket | 1 |
| 13***36 | Screen; (Water Strainer) | 1 |
| 22***37 | Spray Ar-Water | 1 |
160-7021 Strainer Gp-Water
| 16***21 | Strainer Group-Water | 1 |
| 23***74 | Seal | 1 |
| 23***77 | Union | 1 |
229-0652 Tank Gp-Water
| 22***27 | Tank Group-Water | 1 |
| 22***29 | Lines Group-Water Spray | 1 |
| 22***52 | Tank Group-Water | 1 |
229-0653 Tank Gp-Water
| 22***53 | Tank Group-Water | 1 |
228-7778 Tank Gp-Water
| 08***95 | Elbow | 1 |
| 08***33 | Strainer; (Water Tank) | 1 |
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
227-0762 Tank Gp-Water
| 17***60 | Cap As; (Water Tank) | 1 |
| 22***62 | Tank Group-Water | 1 |
| 23***74 | Seal | 1 |
228-7827 Tank Gp-Water
| 22***26 | Tank Group-Water | 1 |
| 22***27 | Tank Group-Water | 1 |
| 22***28 | Lines Group-Water Spray | 1 |
227-0763 Tank Gp-Water
| 08***95 | Elbow | 2 |
| 08***33 | Strainer; (Water Tank) | 1 |
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
228-7826 Tank Gp-Water
| 08***95 | Elbow | 1 |
| 08***54 | Fitting | 1 |
| 08***33 | Strainer; (Water Tank) | 1 |
234-4084 Valve Gp-Control
| 23***84 | Valve Group-Control | 1 |
| 24***13 | Kit-Seal; (Solenoid Valve) | 1 |
| 24***90 | Valve Group-Solenoid; (Flow Control) | 1 |
233-1490 Valve Gp-Solenoid -Hydraulic Lockout
| 23***90 | Valve Group-Solenoid; -Hydraulic Lockout | 1 |
| 24***13 | Kit-Seal; (Solenoid Valve) | 1 |
| 24***14 | Solenoid As; (Flow Control) | 1 |
233-1491 Valve Gp-Solenoid
| 23***91 | Valve Group-Solenoid | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
CB-214E serial number reference
The CB-214E PIN plate is a metal tag mounted on the machine frame, separate from the engine-serial tag on the 3013C block. Read the plate's serial block left to right: the first digits match the sales model number (214) rather than a 3-letter alpha code, followed by the 5-digit production sequence; the sequence number is what determines parts and configuration fitment, not a model-year label. Exact plate placement on the frame is not confirmed from available sources — check the frame near the operator platform or consult the operation and maintenance manual for this model if the plate is not immediately visible.
| Prefix | Identifies | Notes |
|---|---|---|
| 214 | CB-214E vibratory compactor, all-configuration (double smooth steel drum, ride-on paving/utility compactor) | Serial range runs 21400001-UP (shown in parts listings as S/N 2141-UP) under this machine ID, paired with the 3013C naturally aspirated 3-cylinder diesel. This E-series compactor keys its parts catalog off the numeric sales-model code 214 followed by a 5-digit sequence rather than a 3-letter alpha PIN prefix. Production falls in the 2004-2007 window, sitting between the CB-214D (2000-2004) and CB-214C (1995-2000) generations. Only one serial break is documented for this model; no evidence of a mid-run prefix change (e.g. an emissions-tier split) turned up. The 9XK and 3AL alpha prefixes seen in older documentation belong to the CB-214C and CB-224C respectively, not this E-series machine — confirm with dealer if your plate shows something different. |
Frequently asked questions
What engine does the Caterpillar CB-214E use?
The CB-214E runs Caterpillar's 3013C engine, a naturally aspirated, water-cooled, three-cylinder diesel rated at roughly 24.4 kW (32.7 hp) gross. It is mechanically governed with no ECM — just analog gauges and warning lamps, no electronic fault codes.
What is the operating weight of the Caterpillar CB-214E?
Standard CB-214E operating weight runs approximately 2,450 to 2,490 kg (5,400 to 5,490 lb) with ROPS, full fuel, and a half-full water tank, varying with tire size and dealer configuration. The wide-track CB-214E XW variant, with a 1400 mm drum, weighs closer to 3,125 kg (6,890 lb).
What replaced the Caterpillar CB-214E?
Caterpillar built the CB-214E from roughly 2004 to 2007, sharing its Operation and Maintenance Manual with the CB-224E and the CB-225E combi roller. It followed the CB-214D, which itself followed the CB-214C. Caterpillar's current light utility compactor lineup, the CB2.5 and CB2.7 series, now covers the same niche.
What CB-214E owners discuss
What engine is actually in the CB-214E, and does it have a reputation among owners?
The CB-214E (and its CB-224E/CB-225E siblings) runs the Cat 3013C, a naturally aspirated 3-cylinder diesel built on the Perkins 403D-15 architecture and also cataloged as the Cat C1.5. It is a mechanically injected engine with no aftertreatment, which owners generally like because it is simple to diagnose and cheap to keep running. The main recurring gripe is hard cold starting: cranking 10 to 20+ seconds before it catches, worse when the machine has sat and noticeably better once warm. Carbon-fouled glow plugs are the first suspect, so test each plug individually with a jumper rather than assuming the whole set is bad. A weak or air-bound engine-driven fuel transfer pump ahead of the injection pump is the second common cause of both hard starting and light stumbling once running.
Why does the roller bog down or nearly stall under load or with vibration engaged?
Owners running this 3013C-powered compactor family report the engine bogging when climbing even a small grade at full propel speed, or when vibration is engaged at full speed on flat ground, sometimes to the point of killing the motor. It is consistently worse cold and only partly improves after 10 minutes of running. This points to partial fuel starvation rather than a mechanical engine fault. Community troubleshooting order: rule out the obvious (fuel filter, tank pickup, air filter), then check further upstream — the elbow fitting feeding the primer, the cavity under the primer bulb for trapped debris, and whether the filter's concentric outer-to-inner tube is restricted. These small NA diesels have little reserve capacity, so even a partial restriction shows up as bogging under load. Exact reports come from the CB-224E variant of this platform; the fuel system and 3013C are shared with the CB-214E, but treat this as a family-wide pattern rather than a CB-214E-specific confirmed defect.
How durable is the hydrostatic propel system, and what wears first?
Propel is a variable-displacement piston pump feeding fixed-displacement drive motors at the front and rear drums, controlled by a single hydrostatic lever for stepless forward/reverse. The drive motors are the wear item most often flagged by mechanics working on this class of tandem roller, especially on machines that spent a lot of time on grade or ramps where the motors work harder. Early warning signs are a whine from the motor housing or a loss of low-speed pulling torque before top-speed performance is affected. Keeping the hydraulic oil clean and changed on schedule is the main preventive measure owners cite. If a machine shows sluggish or one-sided propel, have your dealer verify drive motor case-drain flow and pump output before condemning either component, since loss of controlled propel on a grade is a safety issue, not just a performance one.
What do owners say about the water spray system and nozzle clogging?
Cat built this series with triple filtration specifically to fight the nozzle clogging that is endemic to asphalt rollers in general: a strainer at the tank fill spout, an in-line filter at the electric water pump, and a filter at each spray nozzle. Even with that, plugged nozzles remain the most common water-system complaint reported for rollers in this class, usually from recycled or dirty jobsite water, or algae growth when the tank sits idle between jobs. The practical fix owners use is flushing the tank and pulling the nozzle screens after any extended layup, and checking the in-line filter at the pump before assuming the pump itself has failed — a starved pump can mimic a dead pump.
What wears on the undercarriage — articulation joint, scrapers, drum bearings?
Cat markets the articulation (oscillation) joint on this compactor family as maintenance-free, but used-machine buyers and mechanics still check the center joint and its pins for play, since "maintenance-free" does not mean wear-free over thousands of hours. Drum scrapers are spring-loaded non-metallic bars held against the drum to shed asphalt buildup; they are a routine wear part and worn scrapers alone are not a red flag. A scraper that no longer tracks the drum evenly, though, usually means a bent scraper arm or a worn drum bearing rather than just a tired scraper. Eccentric weight and drum bearings run inside a sealed pod-style housing, with an oil change interval commonly cited around 3 years or 3,000 hours (varies by series/configuration) — a housing that is clearly overdue on oil is a bearing-life risk worth flagging.
Are there common electrical or sensor complaints on this machine?
This generation is electrically simple — the 3013C has no complex ECM/sensor network — so most "electrical" complaints reported in the field trace back to basic wiring and connector corrosion (glow plug relay and harness, vibration on/off switch, water pump circuit) rather than sensor or module faults. For a no-start or intermittent no-crank, owners recommend checking battery and charging-circuit grounds and ohming out the glow plug harness before condemning the plugs themselves. Detailed fault-code behavior for this specific model was not well documented in the owner discussions found — if the machine throws a dash warning or acts up electrically, have your dealer pull codes with the proper diagnostic tool to confirm root cause.
What should you check before buying a used CB-214E?
Community consensus points to the same short list every time. Pull service records and do a cold start test — hard, prolonged cranking cold is a known trait even on healthy units, but excessive smoke or no start at all is not normal. Check the hydrostatic drive motors for whine, leaks, or uneven pulling power, especially if the machine's history includes grade work. Check the center articulation joint and pins for play. Inspect the drum shells for cracks or chatter marks and confirm the scrapers track evenly. Verify the water spray system primes and all nozzles flow, and check the eccentric/vibratory housing oil condition against its service interval. Finally, confirm a belt guard is fitted over the vibratory pump belt — Cat issued a product support update to add this guard on affected serial ranges of the CB-214E/CB-224E/CB-225E, and older units may predate it. Because a missing or incorrect belt guard is a moving-belt safety hazard, have your dealer verify the machine's serial number against the covered range and confirm the correct guard is installed before putting the machine into service.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific CB-214E part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.