Caterpillarasphalt paver
Caterpillar BG-600D
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar BG-600D is a mid-size, wheel-type asphalt paver sold under the Barber-Greene badge as a direct running mate to the Cat AP-600D, sharing the same chassis, engine, and screed offering under a different nameplate for its dealer channel. It runs the Cat C6.6 ACERT, a 6-cylinder turbocharged, air-to-air aftercooled diesel rated 129.5 kW/176 hp gross (121.9 kW/165.8 hp net) from 6.6 L displacement, built to EU Stage IIIA/EPA Tier 3 emissions without a DPF, SCR, or DEF system. Operating weight runs about 18,200 kg (40,124 lb) as fitted with the AS4251C double-width hydraulic power extendible screed, which paves 2550-5000 mm standard and hydraulically extends to 7000 mm maximum with LPG or electric heat. The hopper holds 6.5 m3, propulsion is fully hydrostatic to the front wheels through dual-path pumps and two-speed planetary gearboxes rather than a mechanical differential axle, and an onboard 25 kW/60 Hz generator (belt- or hydraulic-driven) powers the electric screed heat and an optional auxiliary power panel. The BG-600D sits in a lineage that traces back to an earlier Tier 2 base BG-600/AP-600 generation and was followed, after the D-series ran its course, by a later Tier 4 relaunch built around a different engine family.
Moving to this D-generation brought the line electronic engine control for the first time, replacing simpler mechanical fueling with the ACERT-managed C6.6 and adding an Advisor display that surfaces fault codes and start-up checklists instead of relying on gauges alone. The independent, chain-driven auger and conveyor system, dual-path hydrostatic wheel drive, and double-width AS4251C screed carried over largely unchanged from the AP-600D badge-mate, so the two model lines overlap heavily on major components even though they are scoped as separate parts catalogs by serial prefix. In the used and parts market the BG-600D still matters because its Tier 3 engine avoids the aftertreatment complexity and cost of later Tier 4 machines, its hydrostatic drivetrain and screed hardware remain in active service on resale machines, and buyers need to key parts lookups to its own B6K serial prefix rather than assuming a one-to-one match with the AP-600D badge or with the later bare-name relaunch, both of which use different prefix families despite closely related hardware.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar BG-600D specifications
Engine
| Engine model | Cat C6.6 with ACERT Technology, 6-cylinder turbocharged air-to-air aftercooled diesel |
| Gross power (SAE J1995) @ 2200 rpm | 129.5 kW / 176 hp |
| Net power (ISO 9249 / EEC 80/1269) @ 2200 rpm | 121.9 kW / 165.8 hp |
| Bore x stroke | 105 mm x 127 mm (4.13 in x 5.0 in) |
| Displacement | 6.6 L (403 cu in) |
| Emissions certification | EU Stage IIIA |
| Altitude derating | Not required up to 3000 m (9,840 ft) |
Weights
| Operating weight with AS4251C screed (std. width 2.55-5 m) | 18,200 kg (40,124 lb) — includes 75 kg operator, canopy, 50% fuel, leveling system |
| Shipping weight, tractor only | 14,000 kg (30,865 lb) |
| Shipping weight, tractor with screed | 17,900 kg (39,462 lb) — canopy lowered, 10% fuel, manual apron, standard screed end gates |
| Ground pressure | Not published for this model |
Dimensions
| Tractor length with push roller | 4950 mm (16.2 ft) |
| Overall length with push roller and screed | 6160 mm (20.2 ft) — varies with screed width configuration fitted |
| Transport width, hopper raised, with screed end gates | 2720 mm (8.9 ft) |
| Transport width, hopper raised, without screed end gates | 2500 mm (8.2 ft) |
| Tractor operating width, hopper lowered | 3306 mm (10.85 ft) |
| Track gauge width | 2200 mm (7.2 ft) |
| Operating height with canopy | 3840 mm (12.6 ft) |
| Transport height, canopy and fumes stack lowered | 3019 mm (9.9 ft) |
| Wheelbase | 2360 mm (7.74 ft) |
| Auger diameter | 406 mm (16 in) |
| Hopper capacity (with conveyor tunnels) | 6.5 m3 (14.1 tonne) |
| Standard paving range (AS4251C screed) | 2550-5000 mm (8.4-16.4 ft); up to 7000 mm (23 ft) with mechanical extensions on electric- or LPG-heat screed |
Performance
| Travel speed range | 0-18 km/h (0-11.2 mph) |
| Paving speed range | 0-25 m/min (0-82 ft/min) |
| Minimum turning radius (maneuver mode) | 1400 mm (4 ft 8 in) |
| Propel modes | Pave, travel, maneuver — dual-path hydrostatic drive with electronic displacement control, two propel ranges forward/reverse |
| Drive tyres | Two 16.00 x 25 radial |
| Steering tyres | Four solid rubber, 559 mm x 330 mm, on oscillating bogies |
| Gradeability | Not published for this model |
Service capacities (summary)
| Fuel tank | 291 L (76.9 US gal) |
| Cooling system, total | 30 L (7.9 US gal) |
| Engine oil with filter | 14 L (3.7 US gal) |
| Hydraulic oil tank | 218 L (57.6 US gal) |
| Washdown spray water tank | 38 L (10 US gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
BG-600D fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) - C6.6 ACERT diesel | approx. 13.5 L (3.6 US gal) | Cat DEO or DEO-ULS diesel engine oil, SAE 15W-40 for temperate climates, drop to SAE 10W-30 in cold weather per Cat's multi-viscosity guidance; engine is Tier 3 (no DPF), so either DEO grade is acceptable |
| Cooling system | 31 L (8 US gal) | Cat ELC (Extended Life Coolant), pre-mixed or concentrate; standard year-round formulation, no separate cold-climate variant called out |
| Fuel tank | 278 L (73 US gal) | ultra low sulfur No. 2-D diesel fuel; switch to No. 1-D or a winter blend in cold ambient conditions |
| Hydraulic system and tank | 219 L (58 US gal) | Cat HYDO Advanced 10 (or equivalent Cat TDTO-spec hydraulic fluid); viscosity grade selected by ambient temperature per Cat's hydraulic oil chart, lighter grade in cold starts |
| Propel drive (wheel hydrostatic drive) | not documented as a separate mechanical final-drive/transaxle system on this wheel-type paver | wheel propel is hydrostatic and serviced through the hydraulic system fluid above; no standalone axle or differential gear-oil fill point for this configuration |
| Grease points (chassis, screed, conveyor/auger drivelines) | spec only, no reservoir capacity | Cat Ultra5 Moly multipurpose grease (or Cat Advanced 3-Moly), reapply at scheduled intervals |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar BG-600D maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
Servicing the BG-600D beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S·O·S sampling on the C6.6 ACERT engine oil and on the shared hydraulic/hydrostatic tank, since asphalt dust loads this system harder than typical earthmoving duty and plugs oil coolers faster than the calendar interval assumes. Trend planetary wheel-hub oil condition alongside hydraulic cleanliness, and watch the Advisor display for fault codes flagging hydrostatic pump or motor wear early. Confirm ELC coolant concentration by sample rather than by sight-gauge appearance alone.
Corrective & Common Repairs
Expect auger and conveyor chain stretch and sprocket wear from constant abrasive mix contact, plus screed heater faults: fouled LPG burner nozzles or failed electric elements that show up as uneven mat temperature. Hydrostatic wheel-motor shaft seals are a recurring leak point, and oscillating front bogie wear shows up as uneven tire contact. Baked asphalt dust plugging the hydraulic oil cooler core is a common root cause behind overheating and hydrostatic drive sluggishness complaints.
Overhaul & Rebuild Points
At major hour milestones, flow-test the dual-path hydrostatic pumps and wheel motors and rebuild or exchange units showing internal wear rather than waiting for a stall on grade. Two-speed planetary wheel-hub bearings, auger gearbox seals, and screed extension slide wear plates and tamper bar components are the other recurring rebuild items. Check C6.6 ACERT turbocharger and injector condition at the same milestones, along with brush and bearing wear on the belt- or hydraulic-driven generator.
Seasonal & Environment Servicing
Before cold-weather paving, confirm coolant protection, verify the hydraulic oil viscosity grade suits the ambient range, and run the LPG or electric screed heater to full temperature before the first pass to avoid mat tearing on a cold plate. In hot, dusty conditions clean the hydraulic and engine cooling cores more often and shorten air filter service intervals to offset faster loading. At end of season, drain the fuel water separator, protect exposed hydrostatic and leveling cylinder rods, grease every point, and drain the washdown spray tank before storage.
BG-600D common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 299-8229 | Filter-Fuel | Fuel system service | Check fitment → |
| 220-8678 | Seal-Ring | Fuel system service | Check fitment → |
| 326-1644 | Filter As-Water Sep & Fuel | Fuel system service | Check fitment → |
| 256-7902 | Filter Element As-Air | Air intake service | Check fitment → |
| 256-7903 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
BG-600D fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| E360 | Low engine oil pressure event, with warning, power-derate, and shutdown severity levels | Low oil level, worn oil pump, plugged oil filter or pickup strainer, or a failed oil pressure sensor | Check oil level and top off first, then verify actual oil pressure with a mechanical gauge before replacing the sensor |
| E361 | High engine coolant temperature event; ECM derates power at higher severity levels, trips near 113 C (235 F) | Low coolant level, restricted radiator core, failed water pump, slipping fan drive, or a stuck thermostat | Check coolant level and radiator for blockage, verify fan and belt operation, then confirm sensor reading against actual coolant temperature |
| E362 | Engine overspeed event, warning at the lower level and power derate once rpm exceeds the trip point | Downhill coasting in gear, throttle linkage fault, or a fuel system malfunction pushing rpm past the set limit | Reduce load and rpm immediately, inspect throttle linkage and governor settings, review logged snapshot data for the rpm reached |
| E2143 | Low engine coolant level event with progressive warning and derate severity levels | Coolant leak, air pocket in the cooling system, or a stuck coolant level sensor float | Check coolant level visually and inspect for external leaks before replacing the coolant level sensor |
| E172 | High air filter restriction event | Clogged air filter element or a restricted intake duct | Inspect and clean or replace the air filter element and check intake piping for collapse or blockage |
| E396 | High fuel rail pressure event | Faulty fuel pressure regulator, plugged fuel return line, or a fuel injection pump fault | Check for a stuck fuel return regulator or restricted return line, pull logged snapshot data before replacing pump components |
| E398 | Low fuel rail pressure event | Restricted fuel supply from a dirty filter or collapsed line, air in the fuel system, or a worn fuel transfer pump | Check fuel filters and supply lines for restriction, prime the system, and confirm transfer pump output pressure |
| 190-8 (CID 190, FMI 8) | Engine speed/timing sensor signal is generating an abnormal frequency, pulse width, or period | Incorrect sensor-to-tone-ring air gap, a damaged tone ring tooth, or a failing speed/timing sensor | Check sensor mounting and air gap first, inspect the tone ring, then replace the sensor if the signal stays erratic |
| 100-3 (CID 100, FMI 3) | Engine oil pressure sensor circuit voltage reading above normal, consistent with an open circuit | Open or shorted-to-power wiring at the oil pressure sensor connector, or a failed sensor | Inspect the sensor connector and harness for damage or corrosion, test sensor supply voltage, replace the sensor if wiring checks out good |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
BG-600D attachments & work tools
Screed - AS4251C double-width hydraulic extendible
Standard factory-fit screed for this wheel paver. Standard paving range 2550-5000 mm (8'4"-16'5"), hydraulic power extension to a maximum 7000 mm (23 ft) with bolt-on extension plates added beyond that. Main and extender plates run 400 mm (15") front to back.
Screed heating
Offered with either electric or LPG (propane) plate heating. Electric heat is powered by the tractor-mounted screed generator; both options are ordered as part of the screed, not field-retrofit.
Screed vibration/compaction package
Variable-frequency tamper bar and vibrators are offered on the AS4251C screed, letting density settings be tuned to mix type and lift thickness independent of paving speed.
Screed extenders (bolt-on)
Beyond the hydraulic power-extension range, hand-set bolt-on extension sections widen the mat further; front-mount and rear-mount extender screed arrangements are both referenced for this class, so exact placement varies by configuration.
Hopper
Front-loading split-wing hopper rated at 6.5 m3 (14.1 tonne) capacity, feeding dual slat conveyors.
Material delivery: conveyors and augers
Left and right conveyors and left and right augers are each hydraulically driven and independently controlled, eliminating manual feeder gates and holding a consistent head of material across the screed width.
Auger extensions / mainframe widening
Hydraulic mainframe (auger/conveyor tunnel) extensions widen material delivery to match the screed's extended paving width; augers and conveyors reverse for clearing blockages.
Screed heat generator
Belt-driven onboard generator rated near 25 kW at 60 Hz supplies the electric screed heat circuit and an auxiliary job-site power panel (about 8 kW, with 120V and 240V receptacles) for lighting and hand tools; output is variable-frequency and reaches full power above roughly 1275 engine rpm.
Operator stations
Dual operator consoles slide/tilt and swing out past the machine frame on each side for sightline down the screed edge when matching a joint or running along a curb; no single fixed operator seat.
Canopy / weather protection
A factory operator canopy is offered as an option over the standing operator platform for sun and weather protection; it is not standard equipment.
Mounting/coupling notes
Screed attaches to the tractor via pull/leveling arms rather than a quick-coupler; extension sections and plates are bolt-together hardware, not hydraulic quick-attach tooling.
All BG-600D assemblies by section
Every catalogued assembly group for the Caterpillar BG-600D. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
270-4254 Air Cleaner Gp
| 06***93 | Clamp-Tubing | 1 |
| 10***05 | Elbow; (90 Degree) | 1 |
| 14***11 | Adapter-Filter | 1 |
270-8357 Air Cleaner Gp
| 21***81 | Cover As | 1 |
| 22***63 | Valve As-Air | 1 |
| 25***02 | Filter Element As-Air; (Primary) | 1 |
270-4255 Exhaust Gp-Flexible
| 06***93 | Clamp-Tubing | 2 |
| 13***49 | Cable As | 2 |
| 24***93 | Muffler | 1 |
288-3582 Manifold Gp-Inlet
| 23***88 | Gasket-Inlet | 1 |
| 27***02 | Dowel | 2 |
| 27***74 | Elbow As-Air Inlet | 1 |
285-3414 Turbocharger Gp
| 03***47 | Ferrule | 3 |
| 03***14 | Nut; (7/16-In) | 1 |
| 10***30 | Bolt; (M10x1.5x20-mm) | 2 |
Basic Engine
279-8837 Camshaft Gp
| 1B***36 | Key-Woodruff | 1 |
| 27***25 | Tappet | 12 |
| 27***26 | Rod-Push | 12 |
282-2827 Cover Gp-Cylinder Block
| 22***22 | Plug-Cup | 1 |
| 27***74 | Plate As-Blk | 1 |
| 27***75 | Seal-O-Ring | 1 |
277-4224 Cover Gp-Engine -Auxiliary Drive
| 10***30 | Bolt; (M10x1.5x20-mm) | 1 |
| 11***22 | Bolt; (M8x16-mm) | 5 |
| 27***23 | Plug | 1 |
282-2825 Cover Gp-Valve Mechanism
| 03***20 | Clip | 2 |
| 12***06 | Seal; (Engine Oil Fill Cap) | 1 |
| 12***81 | Clip | 1 |
279-8762 Crankshaft Gp
| 1B***36 | Key-Woodruff | 1 |
| 22***39 | Dowel | 1 |
| 27***87 | Crankshaft Kt | 1 |
279-8711 Cylinder Block Gp
| 20***19 | Bolt; (M8x1.25x16-mm) | 8 |
| 27***11 | Cylinder Block Group | 1 |
| 29***86 | Housing-Rear | 1 |
306-6845 Cylinder Block Gp
| 06***43 | Plug-Side-(1.251 Dia.) | 5 |
| 10***41 | Bolt; (M6x1x10-mm) | 6 |
| 18***84 | Dowel | 2 |
309-6663 Cylinder Head As
| 19***51 | Seal-O-Ring | 1 |
| 23***22 | Plug | 1 |
| 27***16 | Plug-Core | 6 |
279-8821 Cylinder Head Gp
| 17***41 | Head-Gasket | 1 |
| 27***34 | Bolt-Special; (Cylinder Head) | 14 |
| 27***21 | Cylinder Head Group | 1 |
291-2513 Drain Gp-Engine Oil
| 27***83 | Seal; (Sump Drain Plug) | 1 |
| 29***13 | Drain Group-Engine Oil | 1 |
| 7C***51 | Plug-Drain; (Engine Oil) | 1 |
270-4259 Drain Gp-Engine Oil
| 15***55 | Adapter | 1 |
| 16***35 | Plug As | 1 |
| 20***28 | Hose As | 1 |
289-3265 Drive Gp-Fan
| 11***59 | Bolt; (M10x1.5x35-mm) | 4 |
| 28***26 | Pulley | 1 |
| 28***60 | Belt-Serpentine | 1 |
285-2000 Flywheel Gp
| 03***87 | Ring-Starting Motor; (126-Teeth) | 1 |
| 0S***03 | Bolt,Machine Fuel Pump Drive Gear Mounting | 12 |
| 10***31 | Flywheel As | 1 |
284-0892 Housing Gp-Flywheel
| 11***63 | Bolt; (M8x1.25x12-mm) | 2 |
| 12***83 | Bolt; (M10x1.5x30-mm) | 6 |
| 19***09 | Plug | 1 |
277-3014 Housing Gp-Front
| 06***79 | Dowel | 1 |
| 10***51 | Bolt; (M8x1.25x65-mm) | 5 |
| 10***30 | Bolt; (M10x1.5x20-mm) | 1 |
279-9653 Lifting Gp-Engine
| 27***51 | Plate-Lifting | 1 |
| 27***52 | Plate-Lifting | 1 |
| 27***53 | Lifting Group-Engine | 1 |
300-4431 Mounting Gp-Engine
| 27***90 | Bracket-Mounting | 2 |
| 28***01 | Bolt | 2 |
| 28***02 | Bolt | 6 |
270-4250 Mounting Gp-Engine Flexible
| 15***12 | Mount As | 2 |
| 23***44 | Support As | 1 |
| 23***45 | Support As | 1 |
300-4439 Pan Gp-Oil
| 10***90 | Plug | 1 |
| 12***15 | Bolt; (M8x16x1.25-mm) | 1 |
| 27***83 | Seal; (Sump Drain Plug) | 1 |
279-8780 Piston & Rod Gp
| 12***36 | Ring-Retaining | 2 |
| 22***39 | Bolt-Special; (Connecting Rod) | 2 |
| 27***75 | Piston As | 6 |
277-5007 Plug Gp-Engine
| 27***07 | Plug Group-Engine | 1 |
| 2B***58 | Plug--To Block Upper Front Air Manifold | 3 |
291-4135 Pulley Gp-Crankshaft
| 27***30 | Damper | 1 |
| 27***31 | Pulley | 1 |
| 27***32 | Hub | 1 |
291-4136 Pulley Gp-Fan
| 27***31 | Pulley | 1 |
| 29***36 | Pulley Group-Fan | 1 |
| 29***47 | Adaptor | 1 |
280-1911 Rocker Arm Gp
| 27***00 | Plug-Shaft End | 1 |
| 27***01 | Circlip | 1 |
| 27***06 | Spring-Shaft | 5 |
279-8825 Valve Mechanism Gp
| 27***27 | Link | 12 |
| 27***25 | Valve Mechanism Group | 1 |
| 28***11 | Rocker Arm Group | 1 |
Braking System
193-8539 Pump & Valve Gp-Brake -Manual Release
| 19***39 | Pump & Valve Group-Brake; -Manual Release | 1 |
| 19***41 | Cartridge As-Valve | 1 |
| 20***57 | Kit-Seal; (Flow Control Valve) | 1 |
229-9476 Pump Gp-Hand -Manual Brake Release
| 22***15 | Kit-Seal; (Check Valve)(Manual Brake Release Hand Pump) | 1 |
| 22***76 | Pump Group-Hand; -Manual Brake Release | 1 |
| 23***43 | Knob | 1 |
Controls
276-4579 Adjuster Gp-Height
| 10***03 | Adjuster Group-Height; -Manual | 2 |
| 10***04 | Bolt-Shoulder | 2 |
| 10***24 | Tube As; (Vertical) | 4 |
253-4752 Adjuster Gp-Height
| 10***24 | Tube As; (Vertical) | 4 |
| 10***39 | Key-Square | 2 |
| 10***40 | Spacer; (10.74x17.14x7-mm Thk) | 2 |
102-2703 Adjuster Gp-Height -Manual
| 10***03 | Adjuster Group-Height; -Manual | 1 |
| 10***47 | Gear-Worm | 1 |
| 10***50 | Guide-Bushing | 1 |
197-9844 Chain Gp-Screed
| 10***87 | Link-Connecting | 1 |
| 19***33 | Link-Offset | 1 |
| 19***44 | Chain Group-Screed | 1 |
287-0327 Control Gp-Thickness -Ccw, Acme
| 27***83 | Film-Instruction; (Mat Thickness, Ccw To Increase) | 2 |
| 28***27 | Control Group-Thickness; -Rh Thread | 1 |
| 28***24 | Shaft As | 2 |
277-9934 Control Gp-Thickness -Cw, Acme
| 27***84 | Film-Instruction; (Mat Thickness, Cw To Increase) | 2 |
| 27***34 | Control Group-Thickness; -Lh Thread | 1 |
| 28***90 | Shaft As | 2 |
277-9935 Control Gp-Thickness -Ccw, Acme
| 27***83 | Film-Instruction; (Mat Thickness, Ccw To Increase) | 2 |
| 27***35 | Control Group-Thickness; -Rh Thread | 1 |
| 28***94 | Shaft As | 2 |
287-0326 Control Gp-Thickness -Cw, Acme
| 27***84 | Film-Instruction; (Mat Thickness, Cw To Increase) | 2 |
| 28***26 | Control Group-Thickness; -Lh Thread | 1 |
| 28***26 | Shaft As | 2 |
290-1628 Crown Gp-Power
| 10***39 | Key-Square | 1 |
| 11***50 | Sprocket; (12-Teeth) | 1 |
| 18***45 | Boss; (12.7x25.4x15.7-mm Thk) | 2 |
276-4590 Crown Gp -Basic
| 10***01 | .. Roller, Bearing | 2 |
| 10***38 | Pointer | 1 |
| 10***39 | Key-Square | 1 |
196-2503 Jack Gp-Height Adjuster
| 10***64 | Bearing-Thrust | 2 |
| 11***49 | Worm | 1 |
| 19***03 | Jack Group-Height Adjuster | 1 |
102-2699 Jack Gp-Sloper
| 10***99 | Jack Group-Sloper | 1 |
| 10***46 | Gear-Worm | 1 |
| 10***49 | Guide-Bushing | 1 |
277-2004 Motor Gp-Power Adjuster
| 07***77 | Bushing-Terminal | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***87 | Sleeve; (26-cm) | 0 |
277-2005 Motor Gp-Power Adjuster
| 07***77 | Bushing-Terminal | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***87 | Sleeve; (26-cm) | 0 |
277-2006 Motor Gp-Power Adjuster
| 07***77 | Bushing-Terminal | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***87 | Sleeve; (26-cm) | 0 |
197-9850 Shaft Gp-Drive
| 17***69 | Kit-Bearing; (Universal Joint) | 1 |
| 19***11 | Shaft As | 1 |
| 19***12 | Spindle As | 1 |
197-9849 Shaft Gp-Drive
| 17***69 | Kit-Bearing; (Universal Joint) | 1 |
| 19***11 | Shaft As | 1 |
| 19***45 | Spindle As | 1 |
282-7961 Shaft Gp-Drive -Non-Actuated
| 17***69 | Kit-Bearing; (Universal Joint) | 1 |
| 19***11 | Shaft As | 1 |
| 28***61 | Shaft Group-Drive; -Non-Actuated | 1 |
276-4573 Sloper Gp-Power
| 06***93 | Lockwasher-Bearing | 2 |
| 10***99 | Jack Group-Sloper | 2 |
| 10***00 | . Axle, Rod End | 2 |
Cooling System
281-8748 Connection Gp-Water
| 10***87 | Bolt; (M10x1.5x85-mm) | 1 |
| 12***99 | Bolt; (M10x1.5x40-mm) | 1 |
| 28***44 | Gasket-Water Regulator; (Temperature) | 1 |
281-7381 Cooler Gp-Engine Oil
| 22***44 | Gasket; (Engine Oil Filter Base) | 3 |
| 23***51 | Plate; (Blanking) | 2 |
| 27***38 | Gasket | 2 |
326-7401 Cooler Gp-Engine Oil
| 27***00 | Gasket-Housing | 1 |
| 28***39 | Cooler-Oil; (Engine) | 1 |
| 28***40 | Gasket | 1 |
277-2939 Pump Gp-Water
| 11***29 | Bolt; (M8x1.25x75-mm) | 7 |
| 22***38 | Seal-O-Ring | 1 |
| 22***19 | Gasket | 1 |
270-4257 Radiator & Hyd Oil Cooler Gp
| 00***64 | End; (Hose) | 1 |
| 00***70 | Tee-Pipe | 1 |
| 03***39 | Connector | 1 |
333-7770 Radiator & Hyd Oil Cooler Gp
| 31***15 | Radiator As | 1 |
| 31***16 | Cooler As-Oil; (Hydraulic) | 1 |
| 33***70 | Radiator & Hydraulic Oil Cooler Group | 1 |
Electrical And Starting System
3e-6328 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 3E***65 | Wedge; (Receptacle Lock) (2 Pin) | 1 |
285-3080 Alternator Gp-Charging
| 10***51 | Bolt; (M8x1.25x130-mm) | 1 |
| 11***49 | Nut; (M12-1.75x93-mm-Thd) | 1 |
| 14***83 | Bolt; (M10x1.5x45-mm)(Starter Motor) | 2 |
269-8366 Battery & Wiring Gp
| 06***88 | Locknut; (1-11-1/2-Thd) | 1 |
| 10***03 | Plate-Cover | 7 |
| 10***00 | Terminal As-Battery; (Remote Jump Start, Positive) | 1 |
262-4121 Electrical Ar
| 26***21 | Electrical Ar | 1 |
| 26***65 | Console Group-Operator | 1 |
| 26***66 | Battery & Wiring Group | 1 |
262-1421 Electronics Gp-Communication -Product Link 300
| 12***74 | Screw-Pan Head; (8-32x9.52-mm) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 26***21 | Electronics Group-Communication; -Product Link 300 | 1 |
316-2543 Electronics Gp-Machine
| 31***43 | Electronics Group-Machine; -Operator Control | 1 |
| 32***19 | Software Group-Machine; (Master Operator Station Ecm) | 1 |
| 32***20 | Service Group-Machine; (Master Operator Station Ecm) | 1 |
316-2544 Electronics Gp-Machine
| 31***44 | Electronics Group-Machine | 1 |
| 32***59 | Software Group-Machine | 1 |
| 32***61 | Service Group-Machine | 1 |
316-3351 Electronics Gp-Monitor
| 31***51 | Electronics Group-Monitor | 1 |
| 32***83 | Software Group-Monitor | 1 |
| 32***84 | Service Group-Monitor | 1 |
270-5315 Generator Gp
| 14***11 | Plug Group | 1 |
| 16***80 | Plug As. | 1 |
| 16***16 | Plug As | 1 |
289-5220 Generator Gp
| 23***32 | Generator Group | 1 |
| 27***63 | Plate | 1 |
| 28***20 | Generator Group; -Hydraulic | 1 |
231-1332 Generator Gp
| 23***32 | Generator Group | 1 |
277-4410 Glow Plug Gp
| 10***38 | Bolt; (M6x20-mm) | 1 |
| 27***28 | Insulator | 1 |
| 27***08 | Cable As | 1 |
294-8412 Harness As-Engine
| 21***39 | Strap-Cable | 4 |
| 26***41 | Harness As-Engine | 1 |
| 27***09 | Bracket | 1 |
311-6865 Installation Gp-Communication -Product Link
| 26***21 | Electronics Group-Communication; -Product Link 300 | 1 |
| 26***88 | Radio Group-Communication; -Product Link 121sr | 1 |
| 30***89 | Antenna; (Flexible), Captive Washer Cap Screw; 1/2 - 13 X 4 3/4 In., Captive Washer Cap Screw, Screw, Captive Washe; 1/2-13 X 4 3/4" | 1 |
234-4323 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 23***23 | Lamp Group-Flood; -Vertical Mount | 1 |
110-7563 Lamp Gp-Warning Beacon -Strobe Light
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***63 | Lamp Group-Warning Beacon; -Strobe Light | 1 |
| 12***58 | Tube-Flash; (3 Prong Connection)(Warning Beacon) | 1 |
276-1830 Lighting Gp-Flood
| 23***23 | Lamp Group-Flood; -Vertical Mount | 4 |
| 27***30 | Lighting Group-Flood | 1 |
| 8T***33 | Nut (M10x1.50 Thd) | 2 |
198-8284 Lighting Gp-Warning Beacon
| 03***14 | Screw; (10-32x1-In) | 3 |
| 11***63 | Lamp Group-Warning Beacon; -Strobe Light | 1 |
| 11***20 | Tube As | 1 |
258-6918 Mounting Gp-Sensor -Sonic Sensor
| 25***18 | Mounting Group-Sensor; -Sonic Sensor | 1 |
| 28***75 | Collar | 4 |
| 28***79 | Washer; (32.5x63.5x7.1-mm Thk) | 2 |
326-6194 Panel Gp-Circuit Breaker
| 11***18 | Clip | 3 |
| 11***34 | Switch Group-Magnetic; -Start Relay | 2 |
| 16***38 | Switch Group-Magnetic; -Main Relay-Main Power Relay | 1 |
292-7947 Panel Gp-Circuit Breaker
| 10***84 | Relay As; (24-Volt) | 1 |
| 22***00 | Circuit Breaker As; (25-Ampere)(Heated Mirror) | 1 |
| 23***72 | Strap As | 13 |
306-7612 Panel Gp-Power
| 19***06 | Strip-Terminal | 1 |
| 19***80 | Circuit Breaker As; (20-Ampere)(240-Volt Receptacle) | 1 |
| 19***75 | Receptacle | 2 |
263-9088 Radio Gp-Communication -Product Link 121sr
| 26***88 | Radio Group-Communication; -Product Link 121sr | 1 |
330-6085 Sensor & Mounting Gp
| 10***49 | Plate | 2 |
| 13***21 | Handle | 4 |
| 14***10 | Collar | 2 |
198-8279 Sensor Gp-Auger
| 09***67 | Setscrew-Socket; (M10x1.5-Thd) | 2 |
| 11***07 | Knob | 2 |
| 12***44 | Paddle As | 2 |
195-8090 Sensor Gp-Position
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 19***90 | Sensor Group-Position; -Steering | 1 |
294-0112 Sensor Gp-Position
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***24 | Clamp | 2 |
| 16***41 | Support-Sensor | 2 |
219-2385 Sensor Gp-Position
| 12***50 | Receptacle As | 1 |
| 12***51 | Bushing | 1 |
| 12***52 | Clamp As-Cable | 1 |
160-2443 Sensor Gp-Position
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***43 | Sensor Group-Position; -Brake Pedal | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
284-8876 Sensor Gp-Position
| 22***22 | Kit-Hub; (Grade Sensor) | 1 |
| 28***76 | Sensor Group-Position | 1 |
| 3B***08 | Lockwasher Handrails To Dash | 1 |
145-7028 Sensor Gp-Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***28 | Sensor Group-Temperature; -Hydraulic Oil Temp | 1 |
| 15***43 | Sleeve; (2.8-Dm) | 0 |
322-9152 Sensor Gp-Temperature
| 18***55 | Fitting-Pipe | 1 |
| 1F***13 | Locknut; (3/4-In) | 2 |
| 32***51 | Fitting | 1 |
322-9153 Sensor Gp-Temperature
| 1F***13 | Locknut; (3/4-In) | 2 |
| 23***80 | Fitting; (Pipe) | 1 |
| 32***51 | Fitting | 1 |
334-7882 Sensor Gp-Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
| 12***76 | Tube-Heat Shrink; (17.78-mm Dia)(140-cm) | 0 |
296-1288 Electronics Gp-Machine
| 29***88 | Software Group-Implement | 1 |
| 32***35 | Software Group-Machine | 1 |
| 33***58 | Service Group-Machine | 1 |
292-7884 Starting Motor Gp-Electric
| 10***78 | Bolt; (M10x1.5x55-mm) | 2 |
| 29***59 | Starting Motor-Electric | 1 |
| 29***60 | Bolt | 1 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
8n-0694 Switch As-Toggle
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 3 |
| 6T***31 | Nut-Hexagon-(15/32-32 Thd) | 2 |
| 6T***32 | Lockwasher 15.08mm(.59in.)O.D. | 1 |
172-8660 Switch Gp-Liquid Level
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***60 | Switch Group-Liquid Level; -Rear Engine Oil-Ster, Hydraulic Fan Oil-Engine On-Steering Oil, Engine Off-Auxiliary Coolant-Front Engine Oil-Brake Oil, Hoist-Engine Coolant-Tc Oil-Low, Cold | 1 |
| 9X***01 | Pin-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 2 |
175-2309 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***81 | Switch As-Magnetic; (Start Relay) | 1 |
175-2308 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
118-3534 Switch Gp-Magnetic
| 11***34 | Switch Group-Magnetic; -Start Relay | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
| 17***09 | Switch Group-Magnetic; -24-Volt-Start Relay | 1 |
167-0138 Switch Gp-Magnetic
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***38 | Switch Group-Magnetic; -Main Relay-Main Power Relay | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
165-5970 Switch Gp-Toggle
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***70 | Switch Group-Toggle; -Engine Shutoff-Starting Aid-Diagnostic Mode Select | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
269-8370 Wiring Gp-Electronic Control
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***27 | Screw-Pan Head; (M3x0.5x16-mm) | 2 |
| 12***74 | Cover-Connector; (Wire Router) | 2 |
276-4607 Wiring Gp-Heater
| 10***05 | Plate | 4 |
| 15***83 | Clamp-Half | 8 |
| 17***15 | Strap; (Dual Clamp) | 3 |
293-6541 Wiring Gp-Heater
| 10***05 | Plate | 10 |
| 15***83 | Clamp-Half | 4 |
| 17***15 | Strap; (Dual Clamp) | 2 |
297-1002 Wiring Gp-Hydraulic Generator
| 13***00 | Clip; (Tab) | 1 |
| 29***02 | Wiring Group-Hydraulic Generator | 1 |
| 29***04 | Harness As-Solenoid | 1 |
269-8369 Wiring Gp-Machine -Rear
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 7 |
| 13***40 | Resistor As-Connection; (3-Pin) | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
269-8368 Wiring Gp-Machine -Rh
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***01 | Plate-Face | 1 |
292-0971 Wiring Gp-Machine -Lh
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 0L***07 | Grommet | 1 |
| 11***01 | Plate-Face | 2 |
283-4417 Wiring Gp-Panel
| 19***81 | Circuit Breaker As; (35-Ampere)(Generator) | 1 |
| 24***09 | Plate | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
306-7603 Wiring Gp-Panel
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 25***11 | Relay As; (24-Volt)(Screed Control) | 4 |
| 27***12 | Plate As | 1 |
302-3912 Wiring Gp-Power Receptacle
| 19***81 | Circuit Breaker As; (35-Ampere)(Generator) | 1 |
| 24***09 | Plate | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
269-8371 Wiring Gp-Power Train
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 3 |
| 13***00 | Clip; (Tab) | 1 |
| 13***01 | Clip | 5 |
293-6625 Wiring Gp-Screed
| 06***44 | Grommet | 2 |
| 13***00 | Clip; (Tab) | 7 |
| 13***72 | Cover | 4 |
277-5772 Wiring Gp-Screed
| 25***92 | Circuit Breaker As; (25-Ampere)(Extender Heater, Rh) | 4 |
| 27***72 | Wiring Group-Screed | 1 |
| 29***69 | Plate | 1 |
276-4552 Wiring Gp-Screed -Screed Extension
| 24***12 | Switch As-Toggle; (Right Extender Width Sw) | 3 |
| 26***84 | Bracket | 1 |
| 27***42 | Film-Identification; (Screed Extension) | 1 |
276-4606 Wiring Gp-Screed -24-Volt
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 24 |
| 13***00 | Clip; (Tab) | 10 |
| 13***89 | Clip; (Ladder) | 2 |
Electrical System
294-8232 Box Gp-Screed Control -Basic, Left
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***00 | Clip; (Tab) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
289-3575 Box Gp-Screed Control -Basic, Right
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***01 | Clip | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
289-3576 Box Gp-Screed Control -Basic, Left
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***01 | Clip | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
294-8231 Box Gp-Screed Control
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***00 | Clip; (Tab) | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
Engine Arrangement
242-1319 Engine Ar-Primary
| 24***19 | Engine Ar-Primary | 1 |
| 27***12 | Filter Group-Engine Oil; -Engine | 1 |
| 27***39 | Pump Group-Water | 1 |
262-4106 Installation Ar-Engine
| 24***19 | Engine Ar-Primary | 1 |
| 26***06 | Installation Ar-Engine | 1 |
| 27***50 | Mounting Group-Engine Flexible | 1 |
Feeder Drag And Auger Conveyors
263-6001 Auger Gp
| 10***55 | Plate | 1 |
| 16***89 | Bolt-Hex Head; (M16x2x55mm) | 4 |
| 17***24 | Bar | 2 |
116-9509 Bearing Gp-Auger
| 10***04 | Nipple-Pipe | 1 |
| 10***18 | Bearing Group-Auger | 1 |
| 11***09 | Bearing Group-Auger | 1 |
201-5584 Bearing Gp-Auger
| 11***94 | Bearing-Insert | 1 |
| 20***83 | Cap | 2 |
| 20***84 | Bearing Group-Auger | 1 |
106-9718 Bearing Gp-Auger
| 01***41 | Setscrew-Socket | 3 |
| 10***18 | Bearing Group-Auger | 1 |
| 3H***40 | Setscrew; (3/8-24x0.375-In) | 2 |
280-9921 Chain Gp-Conveyor
| 28***21 | Chain Group-Conveyor | 1 |
| 28***79 | Bar-Side | 232 |
| 28***80 | Foam Insulation; 40 X 60 X 644 mm, Bar-Side | 116 |
262-4105 Conveyor Ar-Drag & Auger
| 19***48 | Conveyor Group-Drag | 2 |
| 21***70 | Footshaft Group | 2 |
| 26***05 | Conveyor Ar-Drag & Auger | 1 |
191-4421 Conveyor Gp-Auger
| 10***85 | Plate | 2 |
| 10***91 | Pipe | 2 |
| 10***96 | Plate | 1 |
192-5448 Conveyor Gp-Drag
| 05***20 | Pin-Spring | 58 |
| 12***46 | Bar-Feeder | 29 |
| 19***48 | Conveyor Group-Drag | 1 |
263-6007 Door Gp-Access
| 10***56 | Rod; (Prop) | 3 |
| 11***77 | Bumper-Rubber | 4 |
| 12***27 | Spacer; (9x14x3.5-mm Thk) | 2 |
263-6000 Drive Gp-Conveyor
| 10***99 | Sprocket As; (12-Teeth) | 2 |
| 13***92 | Key-Square | 2 |
| 15***91 | Bolt-Hex Head; (M24x3x120mm) | 2 |
231-2043 Extension Gp-Auger -24-In, Lh
| 23***43 | Extension Group-Auger; -24-In, Lh | 1 |
| 31***20 | Tube | 1 |
| 31***21 | Shaft | 1 |
231-3532 Extension Gp-Auger -6-In
| 23***32 | Extension Group-Auger; -6-In | 1 |
| 31***84 | Tube | 2 |
| 31***60 | Bolt; (M12x1.75x130-mm) | 2 |
243-0329 Extension Gp-Auger -18-In
| 19***87 | Extension Group-Auger; -12-In, Rh | 1 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 1 |
| 23***32 | Extension Group-Auger; -6-In | 1 |
231-2042 Extension Gp-Auger -24-In, Rh
| 23***42 | Extension Group-Auger; -24-In, Rh | 1 |
| 31***20 | Tube | 1 |
| 31***21 | Shaft | 1 |
199-4206 Extension Gp-Auger -12-In, Lh
| 19***06 | Extension Group-Auger; -12-In, Lh | 1 |
| 31***19 | Tube | 1 |
| 31***21 | Shaft | 1 |
198-8287 Extension Gp-Auger -12-In, Rh
| 19***87 | Extension Group-Auger; -12-In, Rh | 1 |
| 31***19 | Tube | 1 |
| 31***21 | Shaft | 1 |
215-1870 Footshaft Gp
| 00***54 | Cup-Roller Bearing | 4 |
| 06***92 | Washer | 2 |
| 10***35 | Cone As-Bearing | 4 |
263-6002 Guard Gp-Conveyor
| 12***54 | Screw-Flat Head; (M12x1.75x35-mm) | 64 |
| 19***39 | Plate | 4 |
| 19***40 | Plate | 2 |
269-7123 Hydraulic Ar-Conveyor
| 23***97 | Motor & Mtg Group-Auger | 1 |
| 26***23 | Hydraulic Ar-Conveyor | 1 |
| 27***14 | Pump & Mtg Group-Conveyor | 1 |
270-7215 Motor & Mtg Gp-Conveyor
| 11***80 | Elbow | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
| 14***58 | Elbow As | 2 |
191-4411 Planetary Gp-Auger
| 09***92 | Pin-Spring | 2 |
| 13***16 | Kit-Washer; (Planetary) | 1 |
| 13***30 | Plug-Magnetic; (Planetary) | 1 |
192-7962 Planetary Gp-Conveyor
| 09***92 | Pin-Spring | 2 |
| 13***63 | Bearing | 1 |
| 16***54 | Seal | 1 |
270-7214 Pump & Mtg Gp-Conveyor
| 08***56 | 90 Degrees Elbow | 1 |
| 14***27 | Connector Group | 2 |
| 14***39 | Connector As. | 8 |
263-6003 Shaft Gp-Feeder Drive
| 03***10 | Setscrew-Socket; (1/2-13x1.25-In) | 4 |
| 10***30 | Bearing-Flange | 2 |
| 10***70 | Key-Square | 2 |
Frame And Body
276-4589 Arm Gp-Drop
| 10***68 | Nipple-Pipe | 2 |
| 11***99 | Pin As-Pivot | 2 |
| 13***77 | Lockout | 4 |
300-9991 Arm Gp-Drop
| 13***20 | Shaft | 2 |
| 13***77 | Lockout | 2 |
| 17***69 | Kit-Bearing; (Universal Joint) | 1 |
271-2815 Arm Gp-Tow
| 00***39 | Bearing-Aligning; (Self Aligning) | 4 |
| 19***19 | Roller | 4 |
| 19***20 | Shaft | 2 |
106-9689 Brace Gp
| 10***89 | Brace Group | 1 |
| 10***62 | Tube As-Brace | 1 |
| 10***64 | Tube As-Brace | 1 |
315-1101 Brace Gp
| 1A***68 | Nut | 1 |
| 31***01 | Brace Group | 1 |
| 31***02 | Plate As | 1 |
263-6006 Bracket Gp-Support
| 13***49 | Cable As | 2 |
| 26***06 | Bracket Group-Support | 1 |
| 31***59 | Plate | 2 |
282-8500 Bracket Gp-Support
| 12***73 | Extension As | 2 |
| 12***20 | Shim; (1.65-mm Thk) | 4 |
| 24***82 | Plate | 4 |
232-1107 Bracket Gp-Support
| 22***51 | Bracket | 1 |
| 23***07 | Bracket Group-Support | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 4 |
295-3079 Carriage Gp-Extender
| 16***39 | Bolt; (5/8-11x3.5-In) | 6 |
| 18***25 | Scraper; (Brass) | 6 |
| 19***57 | Scraper As | 6 |
293-9898 Cover Gp-Access
| 10***14 | Knob | 3 |
| 19***64 | Plate | 2 |
| 20***04 | Plate | 2 |
272-2384 Cover Gp-Platform
| 27***43 | Cover | 2 |
| 27***84 | Cover Group-Platform | 1 |
| 9X***42 | Screw-Truss Head (M6x1.0x12mm); (M6x1.00x12mm) | 6 |
276-4582 Deflector Gp
| 10***31 | Nut-Spring | 8 |
| 10***84 | Screw-Flat Head; (1/2-13x1.5-In)(22.22x7.94x1/2-13 Thd) | 8 |
| 12***80 | Locknut; (M12x1.75-Thd) | 18 |
231-1983 Extension Gp-Main Frame -24-In
| 10***90 | Extension As | 1 |
| 23***83 | Extension Group-Main Frame; -24-In | 1 |
| 7X***53 | Bolt-Plt; (M16 X 2.0 X 40) | 3 |
231-1982 Extension Gp-Main Frame -12-In
| 10***88 | Extension As | 1 |
| 23***82 | Extension Group-Main Frame; -12-In | 1 |
| 7X***53 | Bolt-Plt; (M16 X 2.0 X 40) | 3 |
215-7553 Extension Gp-Main Frame
| 20***86 | Pin | 4 |
| 21***50 | Bracket As; (Lh) | 1 |
| 21***51 | Bracket As; (Rh) | 1 |
279-2576 Flashing Gp
| 15***74 | Bolt-Round Head; (M12x1.75x60-mm) | 5 |
| 25***07 | Bolt-Round Head; (M12x1.75x65-mm) | 1 |
| 27***62 | Flashing | 1 |
279-2577 Flashing Gp
| 27***90 | Flashing | 2 |
| 27***42 | Plate | 2 |
| 27***50 | Flashing | 2 |
293-9899 Frame Gp-Main
| 14***93 | Bolt; (M12x1.75x40-mm) | 8 |
| 27***37 | Angle As; (Lh) | 1 |
| 27***39 | Angle As; (Rh) | 1 |
276-4604 Frame Gp-Screed
| 10***31 | Nut-Spring | 6 |
| 10***83 | Screw-Flat Head; (1/2-13x1-In) | 10 |
| 11***50 | Clamp As; (Bar) | 2 |
295-3080 Frame Gp-Screed
| 19***12 | Plate | 2 |
| 1D***06 | Nut 13.89 mm (.546 In.) | 4 |
| 20***59 | Pin-Lock | 2 |
276-4603 Gate Gp-End
| 10***19 | Locknut; (2-1/4-16-Thd) | 2 |
| 10***47 | Washer | 2 |
| 24***16 | Actuator Group | 4 |
253-4735 Gate Gp-End
| 24***16 | Actuator Group | 4 |
| 25***35 | Gate Group-End | 1 |
| 25***29 | Support As; (Lh) | 1 |
273-9969 Guide Gp-Steering
| 19***54 | Chain | 1 |
| 27***69 | Guide Group-Steering | 1 |
| 27***65 | Bar | 1 |
301-1468 Hitch Gp-Oscillating
| 19***08 | Bar | 2 |
| 19***09 | Pin As | 1 |
| 30***68 | Hitch Group-Oscillating | 1 |
263-6004 Hopper Gp
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 2 |
| 15***91 | Bolt-Hex Head; (M24x3x120mm) | 2 |
| 16***85 | Pin As | 2 |
272-2320 Hopper Gp
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 1 |
| 26***33 | Pin As | 1 |
| 27***32 | Plate As | 1 |
278-8234 Hopper Gp
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 1 |
| 26***33 | Pin As | 1 |
| 27***32 | Plate As | 1 |
273-7452 Lines Gp-Grease
| 14***20 | Connector As | 2 |
| 14***85 | Elbow; (45°) | 8 |
| 14***89 | Elbow As | 6 |
263-5961 Lock Gp-Transport
| 25***97 | Bar | 2 |
| 26***61 | Lock Group-Transport | 1 |
| 31***09 | Plate | 2 |
295-3084 Plate Gp-Screed
| 18***31 | Bolt-Special; (1 1/4-12-2athd) | 4 |
| 1K***72 | Locknut Horn To Guard | 4 |
| 21***69 | Stud | 4 |
276-4605 Plate Gp-Screed
| 26***54 | Shim; (2-mm Thk) | 4 |
| 27***05 | Plate & Heater Group-Screed; -Electric Heat | 1 |
| 29***23 | Nut-Adjustment; (1-1/4-12-Thd) | 44 |
273-1160 Plate Gp
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 1 |
| 26***33 | Pin As | 1 |
| 27***45 | Bar | 1 |
245-9078 Plate Gp-Screed -Electric Heat, 28-In
| 13***89 | Clip; (Ladder) | 2 |
| 24***60 | Plate | 1 |
| 24***78 | Plate Group-Screed; -Electric Heat, 28-In | 1 |
308-3130 Plate Gp-Screed
| 12***64 | Receptacle As-Connector; (1-Pin) | 2 |
| 25***37 | Bracket; (Rh) | 16 |
| 25***01 | Plate-Main | 1 |
245-9077 Plate Gp-Screed -Electric Heat, 12-In
| 13***89 | Clip; (Ladder) | 1 |
| 24***57 | Plate | 1 |
| 24***77 | Plate Group-Screed; -Electric Heat, 12-In | 1 |
311-6561 Plate Gp-Screed
| 12***64 | Receptacle As-Connector; (1-Pin) | 1 |
| 25***75 | Bracket | 16 |
| 25***44 | Spacer; (14.86x19.05x12.5-mm Thk) | 8 |
308-3131 Plate Gp-Screed
| 12***64 | Receptacle As-Connector; (1-Pin) | 2 |
| 25***37 | Bracket; (Rh) | 8 |
| 25***06 | Plate; (Extender, Rh) | 1 |
308-3132 Plate Gp-Screed
| 12***64 | Receptacle As-Connector; (1-Pin) | 2 |
| 25***37 | Bracket; (Rh) | 8 |
| 25***13 | Plate; (Lh Extender) | 1 |
302-3944 Step Gp
| 30***44 | Step Group | 1 |
| 32***85 | Step As | 1 |
| 7F***88 | Pin | 2 |
262-4108 Structural Ar
| 26***08 | Structural Ar | 1 |
| 26***61 | Lock Group-Transport | 1 |
| 27***15 | Arm Group-Tow | 1 |
231-1956 Support Gp-Frame
| 10***89 | Brace Group | 1 |
| 23***56 | Support Group-Frame | 1 |
| 23***07 | Bracket Group-Support | 1 |
263-6008 Suppression Gp-Sound
| 26***08 | Suppression Group-Sound | 1 |
| 27***51 | Insulation-Sound Suppression | 1 |
| 27***52 | Insulation-Sound Suppression | 1 |
270-6763 Ventilation Gp-Paver
| 12***96 | Seal; (1.084m) | 0 |
| 12***23 | Seal; (32-cm) | 0 |
| 14***00 | Inlet-Blower | 1 |
Fuel System
276-0079 Control Gp-Decelerator
| 26***48 | Pedal Group-Governor; -Electronic | 2 |
| 27***36 | Spacer | 2 |
| 27***79 | Control Group-Decelerator | 1 |
201-7654 Cover Gp-Fuel Tank
| 20***53 | Plate | 1 |
| 20***54 | Cover Group-Fuel Tank | 1 |
| 6V***98 | Bolt; (M5x0.8x16-mm) | 5 |
280-1394 Filter Gp-Secondary Fuel
| 28***94 | Filter Group-Secondary Fuel | 1 |
| 29***29 | Filter-Fuel; (Ultra High Efficiency)(Secondary) | 1 |
| 30***80 | .. Bushing, Filter Group-Fuel; (Ultra High Efficiency) | 1 |
174-9570 Filter Gp-Water Sep & Fuel
| 17***70 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 22***78 | Seal-Ring; (Fuel And Water Sep Filter) | 1 |
| 27***20 | Bowl As; (Fuel, Water Separator) | 1 |
306-9380 Injector Gp-Fuel
| 27***39 | Seal | 1 |
| 28***37 | Washer | 1 |
| 30***80 | Injector Group-Fuel | 1 |
321-3600 Injector Gp-Fuel
| 27***39 | Seal | 1 |
| 28***37 | Washer | 1 |
| 32***00 | Injector Group-Fuel | 1 |
320-0677 Injector Gp-Fuel
| 27***39 | Seal | 1 |
| 28***37 | Washer | 1 |
| 32***77 | Injector Group-Fuel | 1 |
292-3780 Injector Gp-Fuel
| 27***39 | Seal | 1 |
| 28***37 | Washer | 1 |
| 29***80 | Injector Group-Fuel | 1 |
308-6532 Lines Gp-Fuel
| 10***16 | Bolt; (M6x16-mm) | 2 |
| 12***15 | Bolt; (M8x16x1.25-mm) | 2 |
| 21***09 | Fitting; (Quick Disconnect, Female) | 1 |
270-4256 Lines Gp-Fuel
| 10***05 | Plate | 3 |
| 10***54 | Connector-Orfs | 1 |
| 12***09 | Valve-Ball; (Hydraulic Tank Drain) | 1 |
276-8398 Pump Gp-Fuel Injection
| 11***85 | Seal-O-Ring; (13.94mm Id) | 1 |
| 22***00 | Seal-O-Ring | 1 |
| 23***20 | Sensor Group-Speed; (Secondary, Timing) | 1 |
291-5919 Pump & Mtg Gp-Unit Inj Hyd
| 11***85 | Seal-O-Ring; (13.94mm Id) | 1 |
| 22***72 | Fitting-Fuel | 1 |
| 22***00 | Seal-O-Ring | 3 |
303-2928 Pump Gp-Fuel Injection
| 10***95 | Bolt; (M8x1.25x35-mm) | 1 |
| 12***15 | Bolt; (M8x16x1.25-mm) | 1 |
| 15***76 | Mount-Isolation | 8 |
278-5319 Pump Gp-Fuel Injection
| 10***95 | Bolt; (M8x1.25x35-mm) | 1 |
| 12***15 | Bolt; (M8x16x1.25-mm) | 1 |
| 15***76 | Mount-Isolation | 8 |
323-3939 Pump Gp-Fuel Injection
| 10***95 | Bolt; (M8x1.25x35-mm) | 1 |
| 12***15 | Bolt; (M8x16x1.25-mm) | 1 |
| 15***76 | Mount-Isolation | 8 |
317-8021 Pump Gp-Fuel
| 11***85 | Seal-O-Ring; (13.94mm Id) | 1 |
| 22***72 | Fitting-Fuel | 1 |
| 22***00 | Seal-O-Ring | 2 |
212-3657 Pump Gp-Fuel Prm & Water Sep -Electric
| 17***70 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 21***57 | Pump Group-Fuel Prm & Water Sep; -Electric-Primary Filter | 1 |
| 21***39 | Filter Base Assembly; (24-Volt) | 1 |
305-6376 Tank Gp-Fuel
| 29***35 | Bulkhead | 1 |
| 29***36 | Nut-Bulkhead; (1-12-Thd, Lh) | 1 |
| 30***76 | Tank Group-Fuel | 1 |
Grade References
109-5626 Leveler Gp -Outboard
| 08***09 | Bracket | 5 |
| 08***38 | Channel | 1 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5624 Leveler Gp -30 Ft Over Screed
| 08***09 | Bracket | 6 |
| 08***38 | Channel | 2 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5625 Leveler Gp -30 Ft Over Screed
| 08***09 | Bracket | 7 |
| 08***38 | Channel | 2 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5622 Leveler Gp -40 Ft Outboard
| 08***09 | Bracket | 12 |
| 08***38 | Channel | 4 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5623 Leveler Gp -30 Ft Outboard
| 08***09 | Bracket | 12 |
| 08***38 | Channel | 4 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5627 Leveler Gp -40 Ft Grade
| 10***04 | Tube; (1.1-M) | 1 |
| 10***27 | Leveler Group; -40-Ft Grade Reference | 1 |
| 10***34 | Tube As | 1 |
109-5628 Leveler Gp -30 Ft Grade
| 10***04 | Tube; (1.1-M) | 1 |
| 10***28 | Leveler Group; -30-Ft Grade Reference | 1 |
| 10***34 | Tube As | 1 |
Hydraulic System
270-6764 Cover Gp
| 14***10 | Plug As; (16.36mm Id) | 1 |
| 20***34 | Plate-Cover | 1 |
| 27***64 | Cover Group | 1 |
303-4148 Cover Gp
| 14***11 | Plug Group | 1 |
| 16***80 | Plug As. | 1 |
| 16***16 | Plug As | 1 |
270-7226 Cylinder & Mtg Gp-Auger
| 14***68 | Elbow Group | 4 |
| 17***51 | Pin-Clevis | 2 |
| 19***59 | Cylinder Group-Hydraulic; -Auger, Rh | 1 |
270-7223 Cylinder & Mtg Gp-Hopper
| 10***44 | Elbow | 1 |
| 14***53 | Elbow, 45,-6 Orb To-6 Orfs-Drum Clutch Port | 2 |
| 20***00 | Elbow As | 2 |
276-5032 Cylinder & Mtg Gp-Screed Hoist
| 14***68 | Elbow Group | 2 |
| 15***33 | Elbow, 45°,-6 Orb /-4 Orfs | 2 |
| 27***60 | Cylinder Group-Hydraulic; -Screed Hoist | 2 |
270-7224 Cylinder & Mtg Gp-Screed Hoist
| 14***74 | Elbow As | 2 |
| 16***88 | Elbow; (90-Deg) | 1 |
| 17***51 | Pin-Clevis | 4 |
270-7227 Cylinder & Mtg Gp-Tow Point
| 00***39 | Bearing-Aligning; (Self Aligning) | 2 |
| 14***74 | Elbow As | 4 |
| 17***51 | Pin-Clevis | 2 |
194-7259 Cylinder Gp-Hydraulic
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 19***59 | Cylinder Group-Hydraulic; -Auger, Rh | 1 |
| 23***20 | Kit-Plug; (Auger Cylinder) | 1 |
275-0895 Cylinder Gp-Hydraulic -Hopper
| 27***95 | Cylinder Group-Hydraulic; -Hopper | 1 |
197-9766 Cylinder Gp-Hydraulic -Slope
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 14***61 | Plug | 2 |
| 14***62 | Seal-Washer | 2 |
194-7260 Cylinder Gp-Hydraulic -Auger, Lh
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 19***60 | Cylinder Group-Hydraulic; -Auger, Lh | 1 |
| 23***18 | Kit-Seal; (Auger Cylinder, Lh) | 1 |
195-2884 Cylinder Gp-Hydraulic -Tow Point
| 19***84 | Cylinder Group-Hydraulic; -Tow Point | 1 |
| 23***82 | Kit-Seal; (Tow Point Cylinder) | 1 |
| 5D***86 | Locknut; (7/8-14-Thd) | 1 |
135-0218 Cylinder Gp-Hydraulic -Extender
| 03***39 | Ring-Back-Up | 1 |
| 12***75 | Ring-Wear | 2 |
| 13***18 | Cylinder Group-Hydraulic; -Extender | 1 |
270-3560 Cylinder Gp-Hydraulic
| 25***75 | Ring-Retaining | 1 |
| 27***60 | Cylinder Group-Hydraulic; -Screed Hoist | 1 |
| 2K***37 | Nut (National Fine); (3/4-16-Thd) | 1 |
270-4253 Drive Gp-Pump
| 00***46 | Elbow; (45 Degree Pipe) | 1 |
| 09***19 | Plug-Pipe | 1 |
| 14***12 | Adapter As | 2 |
176-9415 Filter Gp-Oil -Hydraulic Tank
| 05***19 | Filter Element As-Oil; (Hydraulic) | 1 |
| 07***25 | Kit-Seal; (Hydraulic Oil Filter) | 1 |
| 17***15 | Filter Group-Oil; -Hydraulic Tank | 1 |
262-4122 Hydraulic Ar
| 26***22 | Hydraulic Ar | 1 |
| 26***23 | Hydraulic Ar-Conveyor | 1 |
| 26***24 | Hydraulic Ar-Vibratory | 1 |
308-0518 Hydraulic Ar -Truck Hitch
| 27***65 | Valve & Mtg Group-Truck Hitch | 1 |
| 30***18 | Hydraulic Ar; -Truck Hitch, Cover | 1 |
| 32***24 | Lines Group-Truck Hitch | 1 |
270-6766 Hydraulic Ar
| 27***66 | Hydraulic Ar | 1 |
| 27***63 | Lines Group-Truck Hitch | 1 |
| 27***65 | Valve & Mtg Group-Truck Hitch | 1 |
293-8466 Hydraulic Ar-Auxiliary
| 27***30 | Valve & Mtg Group-Auxiliary | 1 |
| 27***19 | Valve & Mtg Group-Control; -Parking Brake Manual Release | 1 |
| 27***22 | Valve & Mtg Group-Counterbalance; -Hopper Hoist, Tow Point | 1 |
269-7126 Hydraulic Ar-Fan
| 26***26 | Hydraulic Ar-Fan | 1 |
| 27***50 | Pump & Mtg Group-Hydraulic Fan | 1 |
| 27***51 | Motor & Mtg Group-Hydraulic Fan | 1 |
269-7124 Hydraulic Ar-Vibratory
| 26***24 | Hydraulic Ar-Vibratory | 1 |
| 27***31 | Lines Group-Vibratory | 1 |
| 27***32 | Valve & Mtg Group-Vibratory | 1 |
294-4656 Lines Gp-Brake & Shift
| 10***05 | Plate | 1 |
| 11***47 | Hose As | 1 |
| 12***12 | Hose As | 1 |
270-7217 Lines Gp-Conveyor
| 10***43 | Hose As | 1 |
| 10***79 | Hose Assem. | 1 |
| 10***63 | Hose As | 1 |
270-7233 Lines Gp-Cylinder
| 10***05 | Plate | 3 |
| 10***45 | Clamp | 6 |
| 13***90 | Hose As | 1 |
295-3078 Lines Gp-Extender
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 2 |
| 15***36 | Elbow As. | 2 |
| 16***32 | Pin | 2 |
276-4585 Lines Gp-Extension
| 10***05 | Plate | 1 |
| 13***18 | Cylinder Group-Hydraulic; -Extender | 2 |
| 14***27 | Connector Group | 1 |
289-5222 Lines Gp-Generator
| 13***48 | Hose As; (Labeled F) | 1 |
| 14***09 | Hose As | 1 |
| 14***60 | Elbow Group | 1 |
270-7231 Lines Gp-Hopper
| 27***31 | Lines Group-Hopper | 1 |
| 27***51 | Hose As | 2 |
| 6R***28 | Hose As | 2 |
274-5856 Lines Gp-Hopper
| 10***03 | Plate-Cover | 5 |
| 14***67 | Elbow Group; (Each Includes) | 1 |
| 14***77 | Elbow As. | 1 |
278-7739 Lines Gp-Hopper
| 10***03 | Plate-Cover | 5 |
| 14***67 | Elbow Group; (Each Includes) | 1 |
| 14***77 | Elbow As. | 1 |
270-7253 Lines Gp-Hydraulic Fan
| 14***38 | Elbow | 1 |
| 14***12 | Reducer As-Orfs | 1 |
| 14***29 | Tee As-Orfs | 1 |
278-1868 Lines Gp-Paver Ventilation
| 14***58 | Elbow As | 1 |
| 17***15 | Strap; (Dual Clamp) | 1 |
| 19***35 | Hose As | 1 |
294-4657 Lines Gp-Pump -Auxiliary
| 10***23 | Hose As | 1 |
| 17***20 | Strap-Dual Clamp | 3 |
| 1P***82 | Flange-Half | 2 |
270-7244 Lines Gp-Return
| 15***36 | Hose As | 1 |
| 19***06 | Bolt-Stacking; (M6x1x64-mm) | 2 |
| 1P***82 | Flange-Half | 2 |
270-7229 Lines Gp-Screed
| 10***05 | Plate | 8 |
| 10***95 | Hose As | 1 |
| 14***57 | Clamp-Double | 4 |
253-4756 Lines Gp-Slope
| 10***40 | Spacer; (10.74x17.14x7-mm Thk) | 4 |
| 10***84 | Pin As | 4 |
| 14***74 | Elbow As | 10 |
270-7246 Lines Gp-Slope
| 10***05 | Plate | 3 |
| 15***28 | Union | 1 |
| 15***46 | Tee As | 2 |
308-0516 Lines Gp-Steering
| 10***03 | Plate-Cover | 9 |
| 14***52 | Union As | 2 |
| 15***90 | Bolt-Stacking; (M8x1.25x33-mm) | 6 |
273-2463 Lines Gp-Hitch
| 10***03 | Plate-Cover | 5 |
| 10***05 | Plate | 1 |
| 13***18 | Tube As | 2 |
322-0224 Lines Gp-Truck Hitch
| 10***03 | Plate-Cover | 6 |
| 10***05 | Plate | 1 |
| 13***18 | Tube As | 2 |
270-3531 Lines Gp-Vibratory
| 11***05 | Hose As; (Main Auxiliary Valve) | 1 |
| 14***26 | Hose As; (Vibe Valve Outlet) | 1 |
| 14***80 | Elbow As | 1 |
276-4584 Lines Gp-Vibratory
| 10***03 | Plate-Cover | 1 |
| 10***05 | Plate | 3 |
| 11***60 | Strap | 1 |
295-3083 Lines Gp-Vibratory
| 10***05 | Plate | 4 |
| 10***03 | Manifold; (Forward Return,Rear Return) | 1 |
| 14***09 | Adapter As | 3 |
294-4659 Manifold Gp-Hydraulic -Auxiliary
| 10***03 | Manifold; (Forward Return,Rear Return) | 1 |
| 14***08 | Adapter As | 1 |
| 14***35 | Connect Group; (Each Includes) | 1 |
230-9597 Motor & Mtg Gp-Auger
| 11***80 | Elbow | 1 |
| 14***27 | Connector Group | 4 |
| 14***72 | Elbow Group | 4 |
289-5224 Motor & Mtg Gp-Generator
| 14***19 | Connector As | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
| 20***11 | Valve-Check | 1 |
270-7251 Motor & Mtg Gp-Hydraulic Fan
| 14***17 | Adapter, -12 Orb / -16 Orfs | 2 |
| 14***65 | Elbow | 1 |
| 27***51 | Motor & Mtg Group-Hydraulic Fan | 1 |
294-4652 Motor & Mtg Gp-Propel
| 12***47 | Elbow | 1 |
| 14***53 | Elbow, 45,-6 Orb To-6 Orfs-Drum Clutch Port | 2 |
| 15***58 | Elbow As | 2 |
278-0492 Motor & Mtg Gp-Ventilation
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 2 |
| 14***74 | Elbow As | 1 |
| 15***50 | Elbow As | 1 |
235-4849 Motor Gp-Gear
| 23***49 | Motor Group-Gear; -Paver Ventilation | 1 |
| 26***11 | Kit-Seal; (Paver Ventilation Motor) | 1 |
308-2125 Motor Gp-Gear
| 30***25 | Motor Group-Gear; -Vibratory | 1 |
| 31***08 | Kit-Seal | 1 |
230-9384 Motor Gp-Piston -Conveyor
| 12***17 | Pin | 1 |
| 12***68 | Plate-Valve | 1 |
| 13***17 | Washer; (Support) | 1 |
227-5104 Motor Gp-Piston -Generator
| 10***78 | Bearing-Roller | 1 |
| 12***68 | Plate-Valve | 1 |
| 13***17 | Washer; (Support) | 1 |
190-8789 Motor Gp-Piston
| 12***13 | Gasket-End Cap | 1 |
| 12***17 | Pin | 1 |
| 12***68 | Plate-Valve | 1 |
294-2887 Motor Gp-Piston
| 13***84 | Nut; (M14x1.5-Thd) | 10 |
| 14***02 | Spring | 9 |
| 14***49 | Bearing | 1 |
269-0530 Motor Gp-Piston
| 07***53 | Pin; (Spring) | 2 |
| 13***95 | Orifice | 2 |
| 13***57 | Plug | 1 |
294-3078 Pump & Mtg Gp-Auxiliary -Auxiliary
| 10***20 | Seal-O-Ring | 1 |
| 14***72 | Elbow Group | 1 |
| 26***62 | Pump Group-Piston; -Auxiliary | 1 |
289-5221 Pump & Mtg Gp-Generator
| 10***20 | Seal-O-Ring | 1 |
| 14***72 | Elbow Group | 1 |
| 14***85 | Elbow; (45°) | 1 |
270-7250 Pump & Mtg Gp-Hydraulic Fan
| 27***50 | Pump & Mtg Group-Hydraulic Fan | 1 |
| 29***05 | Pump Group-Gear; (Hydraulic Fan) | 1 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 2 |
285-4088 Pump Gp-Piston
| 03***39 | Seal-O-Ring (Id=9.25mm) | 4 |
| 07***53 | Pin; (Spring) | 2 |
| 09***08 | Bolt-Socket Head; (M16x2x140-mm) | 4 |
269-0562 Pump Gp-Piston -Auxiliary
| 26***62 | Pump Group-Piston; -Auxiliary | 1 |
269-0533 Pump Gp-Piston
| 09***74 | Bolt-Socket Head; (M5x0.8x12-mm) | 12 |
| 26***60 | Dowel | 4 |
| 26***33 | Pump Group-Piston; -Conveyor | 1 |
289-5227 Pump Gp-Piston
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 4 |
| 14***11 | Bolt-Socket Head; (M6x1x16-mm) | 1 |
| 23***60 | Pin-Slotted | 1 |
269-7127 Tank & Mtg Gp-Hydraulic
| 08***56 | 90 Degrees Elbow | 1 |
| 14***34 | Connector Group | 1 |
| 14***35 | Connect Group; (Each Includes) | 1 |
270-7254 Tank Gp-Hydraulic
| 00***39 | Adapter-Pipe | 1 |
| 13***00 | Clip; (Tab) | 2 |
| 14***28 | Sensor Group-Temperature; -Hydraulic Oil Temp | 1 |
274-5857 Valve & Mtg Gp
| 13***89 | Clip; (Ladder) | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 3 |
270-3530 Valve & Mtg Gp-Auxiliary
| 08***56 | 90 Degrees Elbow | 1 |
| 14***19 | Connector As | 1 |
| 14***28 | Connector Assem. | 2 |
305-6385 Valve & Mtg Gp-Control -Hydraulic Oil Cooler Bypass
| 10***03 | Manifold; (Forward Return,Rear Return) | 1 |
| 14***17 | Adapter, -12 Orb / -16 Orfs | 1 |
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 1 |
289-5223 Valve & Mtg Gp-Control -Generator
| 11***49 | Fitting As; (Quick Disconnect) | 2 |
| 14***27 | Connector Group | 1 |
| 14***41 | Connector Group | 1 |
270-7219 Valve & Mtg Gp-Control
| 14***26 | Adapter; (Straight) (-4 Orb X -4 Orfs) | 2 |
| 14***67 | Elbow Group; (Each Includes) | 2 |
| 15***81 | Tee As | 1 |
270-7222 Valve & Mtg Gp-Counterbalance
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 10 |
| 14***68 | Elbow Group | 1 |
| 14***33 | Tee As-Orfs; (1 1/16-12 Thd) | 2 |
270-3559 Valve Gp-Check
| 14***67 | Elbow Group; (Each Includes) | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 2 |
| 26***55 | Kit-Flow Control Valve | 1 |
308-0515 Valve & Mtg Gp-Steering
| 09***03 | Key; (Square) | 2 |
| 14***15 | Connector As | 1 |
| 14***17 | Adapter, -12 Orb / -16 Orfs | 1 |
273-2465 Valve & Mtg Gp-Truck Hitch
| 13***89 | Clip; (Ladder) | 1 |
| 14***61 | Elbow Group | 2 |
| 14***67 | Elbow Group; (Each Includes) | 1 |
270-3532 Valve & Mtg Gp-Vibratory
| 11***80 | Elbow | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
| 14***13 | Reducer As.-Orfs | 1 |
276-2261 Valve Gp-Control
| 25***77 | Kit-Seal; (Generator Control Valve) | 1 |
| 25***79 | Valve As-Needle | 1 |
| 25***80 | Kit-Seal; (Needle Valve) | 1 |
230-9160 Valve Gp-Control -Truck Hitch
| 23***82 | Nut-Special | 1 |
| 23***60 | Valve Group-Control; -Truck Hitch | 1 |
| 24***41 | Kit-Seal; (Pressure Reducing Valve) | 1 |
269-0536 Valve Gp-Control
| 23***82 | Nut-Special | 1 |
| 24***41 | Kit-Seal; (Pressure Reducing Valve) | 1 |
| 25***57 | Kit-Seal; (Check Valve) | 1 |
248-1348 Valve Gp-Control
| 23***73 | Seal-O-Ring | 4 |
| 24***48 | Valve Group-Control; -Piston Pump | 1 |
| 30***49 | Plug-Adjustment, Pipe | 1 |
313-1327 Valve Gp-Flow Divider
| 14***54 | Elbow; (45) (-8/-8 Orb/Orfs) | 2 |
| 14***07 | Plug; (Hex Head) (-6 Orb) (Current) (16***35 Friction Disc Interchangeable With 11***47) (Use All Of One Part Number) | 1 |
| 16***67 | Fitting As; (Quick Disconnect, Male)(Quick Disconnect) | 1 |
275-8981 Valve Gp-Flow Divider
| 22***90 | Nut | 1 |
| 22***91 | Seal-O-Ring | 1 |
| 24***41 | Kit-Seal; (Pressure Reducing Valve) | 1 |
276-6041 Valve Gp-Pump Control
| 03***39 | Seal-O-Ring (Id=9.25mm) | 4 |
| 12***42 | Gasket | 1 |
| 27***41 | Valve Group-Pump Control; -Generator | 1 |
332-1453 Valve Gp-Solenoid
| 33***53 | Valve Group-Solenoid | 1 |
276-6042 Valve Gp-Solenoid
| 26***51 | Kit-Seal; (Solenoid Valve)(Solenoid Valve) | 1 |
| 26***45 | Nut; (1/2-32-Thd) | 1 |
| 27***42 | Valve Group-Solenoid; -Pump Control | 1 |
310-8017 Valve Gp-Solenoid
| 09***74 | Bolt-Socket Head; (M5x0.8x12-mm) | 6 |
| 31***17 | Valve Group-Solenoid; -Piston Pump | 1 |
| 31***18 | Valve-Servo | 2 |
300-0504 Valve Gp-Solenoid
| 25***57 | Kit-Seal; (Check Valve) | 1 |
| 25***37 | Valve Group-Solenoid; (24-Volt) | 1 |
| 27***10 | Coil-Solenoid | 2 |
300-0505 Valve Gp-Solenoid
| 25***57 | Kit-Seal; (Check Valve) | 1 |
| 25***37 | Valve Group-Solenoid; (24-Volt) | 2 |
| 27***10 | Coil-Solenoid | 2 |
276-4572 Vibratory Gp
| 09***99 | Fitting-Grease; (Hydraulic) | 2 |
| 10***35 | Key-Square; (3/16in X 3/4in Lg) | 2 |
| 10***33 | Key-Square; (1/4in X 3/4in Lg) | 4 |
295-3082 Vibratory Gp
| 00***39 | Adapter-Pipe | 4 |
| 10***95 | Bearing | 4 |
| 10***39 | Key-Square | 4 |
Implements
241-9103 Extension Ar-Auger
| 19***87 | Extension Group-Auger; -12-In, Rh | 2 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 2 |
| 21***53 | Extension Group-Main Frame | 1 |
322-6285 Extension Gp-Screed -Electric Heat, 1-Ft
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***89 | Clip; (Ladder) | 4 |
| 16***14 | Clip | 1 |
292-0674 Extension Gp-Screed
| 10***19 | Locknut; (2-1/4-16-Thd) | 2 |
| 10***31 | Bar-Spacer | 1 |
| 10***35 | Key-Square; (3/16in X 3/4in Lg) | 2 |
282-8505 Extension Gp-Screed
| 11***09 | Bearing Group-Auger | 2 |
| 19***87 | Extension Group-Auger; -12-In, Rh | 3 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 3 |
282-8506 Extension Gp-Screed
| 11***09 | Bearing Group-Auger | 2 |
| 19***87 | Extension Group-Auger; -12-In, Rh | 1 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 1 |
292-0673 Extension Gp-Screed
| 10***19 | Locknut; (2-1/4-16-Thd) | 2 |
| 10***32 | Bar-Spacer | 1 |
| 10***34 | Plate | 1 |
282-8507 Extension Gp-Screed
| 11***09 | Bearing Group-Auger | 2 |
| 19***87 | Extension Group-Auger; -12-In, Rh | 2 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 2 |
322-6286 Extension Gp-Screed -Electric Heat, 2-Ft
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***89 | Clip; (Ladder) | 6 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
287-0329 Extension Gp-Screed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 25***11 | Relay As; (24-Volt)(Screed Control) | 1 |
282-8504 Extension Gp-Screed
| 19***87 | Extension Group-Auger; -12-In, Rh | 1 |
| 19***06 | Extension Group-Auger; -12-In, Lh | 1 |
| 21***53 | Extension Group-Main Frame | 1 |
287-0328 Extension Gp-Screed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 25***11 | Relay As; (24-Volt)(Screed Control) | 1 |
270-6765 Hitch Ar-Truck
| 27***65 | Hitch Ar-Truck | 1 |
| 27***63 | Lines Group-Truck Hitch | 1 |
| 27***65 | Valve & Mtg Group-Truck Hitch | 1 |
308-0517 Hitch Ar-Truck
| 27***65 | Valve & Mtg Group-Truck Hitch | 1 |
| 30***68 | Hitch Group-Oscillating | 1 |
| 30***17 | Hitch Ar-Truck | 1 |
301-1469 Hitch Gp-Truck
| 05***12 | Ring-Retaining; (Internal) | 2 |
| 09***55 | Washer; (39x72x1.5-mm Thk) | 8 |
| 11***88 | Guide; (31.9x43.5x9.65-mm Thk)(Roller) | 2 |
306-6518 Indicator Gp-Tow Point
| 19***29 | Bolt-Shoulder; (M8x1.25-Thd) | 2 |
| 30***50 | Plate | 2 |
| 30***52 | Plate As | 2 |
275-2449 Roller Ar-Push
| 19***08 | Bar | 2 |
| 19***09 | Pin As | 1 |
| 27***49 | Roller Ar-Push | 1 |
292-0983 Roller Gp-Push
| 09***55 | Washer; (39x72x1.5-mm Thk) | 8 |
| 10***64 | Shaft As | 2 |
| 16***17 | Roller | 2 |
112-1276 Shaft Gp-Drive -Eccentric Weight
| 02***87 | Fitting-Grease; (Universal Joint) | 1 |
| 11***76 | Shaft Group-Drive; -Eccentric Weight | 1 |
| 24***28 | Seal | 1 |
Lubrication System
277-2912 Filter Gp-Engine Oil
| 26***25 | Filter-Engine Oil | 1 |
| 27***12 | Filter Group-Engine Oil; -Engine | 1 |
277-4262 Pump Gp-Engine Oil
| 27***62 | Pump Group-Engine Oil | 1 |
| 31***45 | Pump-Oil; (Engine) | 1 |
| 6I***90 | Bolt; (M8x1.25x40-mm) | 4 |
277-4694 Valve Gp-Fluid Sampling -Engine Oil
| 19***67 | Seal-O-Ring | 1 |
| 21***33 | Valve As-Fluid Sampling | 1 |
| 23***61 | Plug; (Blanking) | 1 |
Machine Arrangement
335-8378 Chassis Ar
| 26***04 | Hopper Group | 1 |
| 26***07 | Door Group-Access | 1 |
| 26***08 | Suppression Group-Sound | 1 |
335-8375 Common Ar
| 26***05 | Conveyor Ar-Drag & Auger | 1 |
| 26***06 | Installation Ar-Engine | 1 |
| 26***07 | Operator Ar | 1 |
270-6762 Generator Ar-Hydraulic
| 27***62 | Generator Ar-Hydraulic | 1 |
| 28***20 | Generator Group; -Hydraulic | 1 |
| 28***21 | Pump & Mtg Group-Generator | 1 |
276-4539 Screed Ar
| 27***39 | Screed Ar; -As3251c, U.S. | 1 |
| 27***72 | Vibratory Group | 1 |
| 27***73 | Sloper Group-Power | 1 |
294-0947 Screed Ar
| 25***35 | Gate Group-End | 1 |
| 25***52 | Adjuster Group-Height | 1 |
| 25***56 | Lines Group-Slope | 1 |
Operator Station
269-8365 Console Gp-Operator
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***87 | Start Switch Assembly; (Key)(Engine) | 1 |
| 12***74 | Cover-Connector; (Wire Router) | 4 |
282-1792 Steering Gp
| 08***11 | Ring | 1 |
| 11***18 | Clip | 1 |
| 16***32 | Block As-Mounting | 1 |
282-9650 Control Gp-Steering
| 09***03 | Key; (Square) | 2 |
| 28***92 | Control Group-Steering | 2 |
| 28***50 | Control Group-Steering | 1 |
282-9651 Control Gp-Steering
| 09***03 | Key; (Square) | 2 |
| 28***51 | Control Group-Steering | 1 |
| 30***76 | Control Group-Steering | 2 |
305-0776 Steering Gp
| 08***11 | Ring | 2 |
| 09***33 | Key-Square | 1 |
| 19***90 | Sensor Group-Position; -Steering | 1 |
263-6011 Floor Mat Gp
| 23***39 | Floor Mat | 2 |
| 26***11 | Floor Mat Group | 1 |
| 27***41 | Floor Mat | 1 |
278-4175 Guard Gp-Vandalism
| 10***14 | Knob | 2 |
| 13***26 | Bolt; (Shoulder) (M6x1x28.75mm) | 2 |
| 15***93 | Screw-Button Head; (M4x0.7x12-mm) | 2 |
132-3090 Lever Gp-Propel
| 08***31 | Tube As | 1 |
| 08***21 | Gasket | 1 |
| 08***22 | Plate-Mounting | 1 |
250-2297 Meter Gp-Service
| 25***97 | Meter Group-Service; -White Backlight | 1 |
| 4B***43 | Nut,Plain,Hexagon Plate Mtg | 1 |
| 6V***07 | Seal-Rectangular | 1 |
262-4107 Operator Ar
| 19***98 | Seat Group-Suspension; -Vinyl | 1 |
| 26***07 | Operator Ar | 1 |
| 26***54 | Platform Group-Operator; -Rh | 1 |
326-6141 Panel Gp-Control -Rh
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***87 | Switch As-Toggle; (Screed Raise/Hld/Float) | 1 |
| 11***48 | Lamp; (24-Volt, 3-Watt)(Clear)(Fuel Level Gauge) | 1 |
326-6139 Panel Gp-Control -Lh
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***87 | Switch As-Toggle; (Screed Raise/Hld/Float) | 1 |
| 11***18 | Clip | 2 |
261-7148 Pedal Gp-Governor
295-3087 Platform Gp-Operator
| 11***33 | Washer; (11x50x6-mm Thk) | 2 |
| 19***83 | Bolt-Shoulder; (3/8-16x0.63-In) | 2 |
| 19***01 | Bracket | 2 |
268-1854 Platform Gp-Operator -Rh
| 12***70 | Capscrew; (Button Hd) (M8x1.25x20) (G10.9) | 4 |
| 13***64 | Bushing | 2 |
| 13***26 | Bolt; (Shoulder) (M6x1x28.75mm) | 1 |
272-1764 Platform Gp-Operator
| 03***69 | Tube | 4 |
| 25***07 | Spacer; (8.4x14x17-mm Thk) | 4 |
| 27***64 | Platform Group-Operator | 1 |
276-4588 Platform Gp-Operator
| 08***97 | Washer; (13x50x6-mm Thk) | 2 |
| 10***38 | Collar | 1 |
| 14***74 | Extension As-Platform | 2 |
268-1855 Platform Gp-Operator -Lh
| 12***70 | Capscrew; (Button Hd) (M8x1.25x20) (G10.9) | 4 |
| 13***64 | Bushing | 2 |
| 13***26 | Bolt; (Shoulder) (M6x1x28.75mm) | 1 |
199-4298 Seat Gp-Suspension -Vinyl
| 13***40 | Locknut; (M8x1.25-Thd) | 4 |
| 19***98 | Seat Group-Suspension; -Vinyl | 1 |
| 23***67 | Seat Belt Group; (Retractable, 76-mm)(Vinyl) | 2 |
235-3151 Seat Gp-Suspension -Vinyl
| 19***32 | Kit-Foam Back | 1 |
| 20***36 | Kit-Damper | 1 |
| 20***37 | Kit-Seat; (Indicators) | 1 |
106-8541 Umbrella Gp -Bg-225c
| 10***41 | Umbrella Group; -Bg-225c | 1 |
Power Train
312-8767 Assist Gp-Front Wheel
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
| 10***85 | Bolt; (1-14x5-In) | 2 |
| 10***59 | Shim; (0.51-mm Thk) | 2 |
295-5505 Assist Gp-Front Wheel
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
| 10***85 | Bolt; (1-14x5-In) | 2 |
| 10***59 | Shim; (0.51-mm Thk) | 2 |
262-4124 Drive Ar-Final
| 26***24 | Drive Ar-Final | 1 |
| 29***75 | Drive Group-Final | 1 |
294-2875 Final Drive Gp
| 16***69 | Adapter; (Str Thd (-6) Orfs/0) | 2 |
| 29***75 | Drive Group-Final | 1 |
| 31***01 | Housing-Planetary | 2 |
265-7279 Drive Gp-Hydrostatic
| 26***79 | Drive Group-Hydrostatic; -Pump | 1 |
| 27***40 | Kit-Seal; (Pump Drive) | 1 |
| 27***41 | Kit-Bearing | 1 |
293-8465 Hydraulic Ar-Propel
| 29***65 | Hydraulic Ar-Propel | 1 |
| 29***52 | Motor & Mtg Group-Propel | 1 |
| 29***53 | Lines Group-Propel | 1 |
244-3759 Bearing Gp-Axle
| 13***63 | Bearing | 2 |
| 24***25 | Kit-Shim; (Axle Bearing) | 1 |
| 24***59 | Kit-Housing | 1 |
294-4653 Lines Gp-Propel
| 10***37 | Hose As | 1 |
| 11***95 | Hose As | 1 |
| 12***09 | Valve-Ball; (Hydraulic Tank Drain) | 1 |
302-5965 Lines Gp-Propel -Front Wheel Assist
| 10***03 | Plate-Cover | 2 |
| 10***05 | Plate | 2 |
| 10***49 | Plate | 1 |
302-5963 Lines Gp-Propel -Front Wheel Assist
| 10***03 | Plate-Cover | 2 |
| 10***05 | Plate | 2 |
| 10***49 | Plate | 1 |
296-3465 Pump Gp-Dual Propel
| 12***88 | Flange-Split | 4 |
| 14***67 | Connector | 1 |
| 14***15 | Connector As | 1 |
294-2880 Wheel & Tire Gp
| 10***34 | Extension-Valve | 1 |
| 10***35 | Valve-Rim | 1 |
| 29***80 | Wheel & Tire Group | 1 |
294-2881 Wheel & Tire Gp
| 1K***74 | Valve Group; (Tire Inflation) | 1 |
| 29***81 | Wheel & Tire Group | 1 |
| 29***83 | Wheel Group | 1 |
294-2879 Wheel Ar
| 29***79 | Wheel Ar | 1 |
| 29***81 | Wheel & Tire Group | 2 |
294-2878 Wheel Ar
| 29***78 | Wheel Ar | 1 |
| 29***80 | Wheel & Tire Group | 2 |
294-2883 Wheel Gp
| 29***83 | Wheel Group | 1 |
| 29***85 | Wheel As | 1 |
| 2D***65 | Seal-O-Ring | 1 |
294-2882 Wheel Gp
| 29***82 | Wheel Group | 1 |
| 29***84 | Wheel As | 1 |
| 2D***43 | Seal-O-Ring | 1 |
Service Equipment And Supplies
303-8783 Box Gp-Tool
| 29***58 | Hinge As | 2 |
| 30***81 | Door | 1 |
| 30***82 | Tool Box | 1 |
290-2116 Film Gp
| 22***45 | Film-Warning; (Shock Hazard) | 1 |
| 22***54 | Film-Warning; (Universal, Read Omm, Intl) | 1 |
| 22***72 | Film; (Warning) (High Pressure Cyl) (Hydraulic Service Center) | 2 |
286-9968 Film Gp
| 22***30 | Film; (Warning) (High Pressure Cyl) (Platform) | 2 |
| 22***45 | Film-Warning; (Do Not Use Ether, U.S) | 1 |
| 22***28 | Film-Warning; (Shock Hazard) | 1 |
290-2118 Film Gp-International
| 22***45 | Film-Warning; (Shock Hazard) | 1 |
| 22***54 | Film-Warning; (Universal, Read Omm, Intl) | 1 |
| 22***46 | Film-Warning; (No Ether Spray/Air Intk, Intl) | 1 |
290-2117 Film Gp-U.S.
| 22***45 | Film-Warning; (Do Not Use Ether, U.S) | 1 |
| 22***28 | Film-Warning; (Shock Hazard) | 1 |
| 22***13 | Film; (Warning) (Jump Start) (Inside Of Lh Battery Box Cover) | 1 |
306-5155 Kit-Maintenance
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***84 | Relay As; (24-Volt) | 1 |
| 10***86 | Switch Group-Toggle; (Parking Brake Override Control) | 1 |
278-0358 Lines Gp-Spray Down
| 27***58 | Lines Group-Spray Down | 1 |
| 28***78 | Connector | 1 |
| 28***79 | Connector As | 1 |
7r-4741 Lines Gp-Spray Down
| 08***77 | Adapter | 1 |
| 1G***70 | Extension-Curve | 1 |
| 1G***79 | Hose As | 1 |
276-4609 Plate & Film Gp
| 10***14 | Handle | 1 |
| 16***89 | Tack-Fastener | 4 |
| 18***68 | Plate-Serial Number | 1 |
333-2714 Plate & Film Gp
| 11***75 | Film-Identification; (Barber-Greene)(Barber-Greene) | 3 |
| 12***82 | Film-Information; (Height Scale)(Screed) | 1 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
295-3081 Plate & Film Gp
| 15***79 | Film-Instruction; (Grease)(Instructions) | 8 |
| 16***89 | Tack-Fastener | 4 |
| 18***68 | Plate-Serial Number | 1 |
266-4529 Pump & Motor Gp-Washdown -Water
| 26***29 | Pump & Motor Group-Washdown; -Water-Emulsion-Diesel Fuel | 1 |
| 31***68 | Kit-Diaphragm | 1 |
| 31***69 | Kit-Valve | 1 |
278-0357 Reel Gp-Washdown Hose
| 15***02 | Spacer; (11x20x15-mm Thk) | 2 |
| 16***00 | Connector As | 1 |
| 19***88 | Clip | 2 |
270-6875 Washdown Gp
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 09***12 | Clip | 1 |
297-2512 Washdown Gp-Ecology
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 00***14 | Coupling-Pipe | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
270-4461 Washdown Gp
| 00***14 | Coupling-Pipe | 1 |
| 00***83 | Nipple-Pipe; (Hexagon) | 1 |
| 09***12 | Clip | 1 |
Slope And Grade Control
272-0697 Beam Gp-Transverse
| 12***80 | Locknut; (M12x1.75-Thd) | 1 |
| 19***78 | Pad | 2 |
| 27***97 | Beam Group-Transverse | 1 |
279-2461 Control Gp-Grade & Slope
| 10***63 | Clamp | 1 |
| 11***96 | Plug | 1 |
| 11***64 | Cable; (302-cm) | 0 |
209-3130 Control Gp-Grade & Slope
| 11***50 | Kit-Transducer | 1 |
| 11***51 | Kit-Filter; (Foam)(Grade Sensor) | 1 |
| 14***76 | Plug-Connector | 1 |
298-0642 Sensor Gp-Grade
| 10***63 | Clamp | 1 |
| 10***23 | Cable As; (Grade) | 1 |
| 11***95 | Plug | 1 |
258-6580 Sensor Gp-Sonic -Averaging Ski
| 10***08 | Sensor Group-Grade; (Control) | 3 |
| 10***10 | Bail-Temperature | 3 |
| 11***50 | Kit-Transducer | 1 |
282-8520 Sensor Gp-Sonic
| 10***63 | Clamp | 1 |
| 10***08 | Sensor Group-Grade; (Control) | 1 |
| 10***10 | Bail-Temperature | 1 |
330-6084 Sensor Gp-Sonic
| 10***49 | Plate | 2 |
| 13***21 | Handle | 4 |
| 14***10 | Collar | 2 |
257-6255 Ski Gp-Averaging
| 25***29 | Mount As | 2 |
| 25***30 | Mount As | 2 |
| 25***55 | Ski Group-Averaging | 1 |
Undercarriage
312-3647 Bogie Gp -Rh
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
| 08***77 | Plate-Locking | 2 |
| 10***85 | Bolt; (1-14x5-In) | 2 |
312-2262 Bogie Gp -Lh
| 00***31 | Cup-Bearing | 2 |
| 00***43 | Nut | 1 |
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
312-2631 Bogie Gp -Lh
| 00***31 | Cup-Bearing | 4 |
| 00***43 | Nut | 2 |
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
312-2632 Bogie Gp -Rh
| 00***31 | Cup-Bearing | 4 |
| 00***43 | Nut | 2 |
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
312-3646 Bogie Gp -Lh
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
| 07***86 | Wire | 0 |
| 08***77 | Plate-Locking | 2 |
312-2263 Bogie Gp -Rh
| 00***31 | Cup-Bearing | 2 |
| 00***43 | Nut | 1 |
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
311-9347 Bogie Gp
| 06***15 | Nut; (1-1/4-12-Thd) | 1 |
| 10***85 | Bolt; (1-14x5-In) | 2 |
| 10***59 | Shim; (0.51-mm Thk) | 2 |
293-9075 Track Gp
| 29***75 | Track Group | 1 |
| 29***01 | Track-Rubber | 2 |
297-9687 Track Gp
| 28***93 | Track; (Smooth) | 2 |
| 29***87 | Track Group | 1 |
Work Tools
283-5617 Shoe Gp-Cutoff
| 10***82 | Shoe As-Cutoff; (1 Foot) | 1 |
| 10***88 | Shoe As-Cutoff; (2 Foot) | 1 |
| 28***17 | Shoe Group-Cutoff | 1 |
BG-600D serial number reference
The PIN plate on the BG-600D is mounted on the machine frame near the operator's station or engine compartment, same general location used across Cat wheel-type asphalt pavers. The first 3 characters are the prefix identifying the specific model/build series, followed by a sequential unit number - read it as PREFIX + sequence (e.g. B6K00001-UP for the first unit of that series).
| Prefix | Identifies | Notes |
|---|---|---|
| B6K | BG-600D wheel-type asphalt paver, base/only confirmed configuration | Serial range starts B6K1-UP (B6K00001-UP). Paired with the Cat C6.6 diesel engine. Production window is commonly cited as mid-2000s in aftermarket fitment data, but this is not tied to an OEM document - treat exact start/end year as approximate and verify with your dealer. |
Frequently asked questions
What engine powers the Cat BG-600D asphalt paver?
A Cat C6.6 ACERT, a 6-cylinder turbocharged, air-to-air aftercooled diesel producing 129.5 kW/176 hp gross (121.9 kW/165.8 hp net) from 6.6 L displacement, meeting EU Stage IIIA/EPA Tier 3 emissions without a DPF, SCR, or DEF system.
What is the operating weight of the BG-600D?
About 18,200 kg (40,124 lb) as configured with the AS4251C double-width screed at standard paving width. Actual weight shifts with screed width, heat system choice, and options like front- or all-wheel assist, so treat this as a baseline rather than a fixed figure.
What replaced the Cat BG-600D?
There is no confirmed direct one-for-one successor tied to this exact badge. Caterpillar's D-generation Tier 3 line, shared with the AP-600D, was eventually followed by a later Tier 4 relaunch built around a different engine and its own serial-prefix family, run as a separate parts catalog rather than a straight continuation of the BG-600D.
What BG-600D owners discuss
How does the hydrostatic wheel drive on the BG-600D behave compared to a mechanical-final-drive paver?
Propel is fully hydrostatic - there is no separate mechanical final drive at each wheel station. Drive speed is matched automatically to steering angle through a position sensor in the left steering cylinder, so the machine holds a set travel speed through turns without operator throttle correction. Because tow-point tracking depends on that steering-cylinder sensor, a calibration drift shows up as the paver pulling to one side or hunting for speed on grade changes rather than as a mechanical wheel-end fault. With no differential or planetary final drive to service, most drivetrain complaints trace back to hydrostatic pump or wheel-motor charge pressure, or to the steering-angle sensor itself. Have your dealer verify steering-sensor calibration and hydrostatic charge pressure before chasing a tracking complaint into the pump.
What engine quirks come up with the C6.6 ACERT in this machine?
The BG-600D's C6.6 ACERT (EU Stage IIIA / EPA Tier 3) runs HEUI-style injection with no DPF or DEF system, so it skips the regen headaches of later Tier 4 pavers, but the injectors and high-pressure oil supply are the recurring wear item - rough idle and gradual power loss on higher-hour units usually trace there first. Hard or no-start in cold weather is more often linked to the fuel pump and cold-start assist circuit than to the injectors themselves. Fuel and coolant care matter more than the low road-speed duty cycle would suggest: water or dirt in the fuel accounts for most injection complaints, and marginal coolant level or a partly blocked radiator will overheat the C6.6 faster than operators expect. Have your dealer verify injector balance rates and coolant condition if you see intermittent power loss or overheating.
What wears out first on the AS4251C double-width screed?
Extension-tube bushings and pivot points develop play first, and that play shows up directly in mat quality before anything else changes. Extension plates commonly lag the main screed plates in heat-up time, which tears or drags the mix behind the extenders if the crew starts paving before the whole screed is up to temperature. Plate wear itself is checked by thickness at all four corners; a difference side to side or front to back points to the paver running out of alignment rather than simple wear. Depth-crank threads going loose is the other frequent complaint, since it lets the screed move under load even with the crank locked down. Have your dealer verify screed alignment and lift-cylinder condition if mat thickness varies corner to corner.
What electrical or sensor issues come up most often?
Two circuits get blamed most: the feed/material sensors mounted on the heated endgates that regulate auger and conveyor speed, and the steering-angle sensor feeding the hydrostatic drive. Dirty or corroded connectors on the endgate feed sensors are a common cause of surging augers and an inconsistent head of material ahead of the screed, which reads as a rough mat rather than an obvious electrical fault. Because both the propel and feed systems rely on electronic control rather than mechanical linkage, erratic behavior such as stalling, uneven propel, or hunting augers is more often a sensor or connector fault than a control module failure. Have your dealer verify sensor wiring and pull ECM fault codes before replacing a module.
Since it is a wheel paver, what wear pattern should I expect instead of undercarriage wear?
There is no track undercarriage to budget for. Wear concentrates in the push-roller assembly at the front of the machine, which contacts the haul truck's tires, and in the tow-point and leveling-arm pivots referenced by the hydrostatic steering and grade sensors. A worn tow-point pivot produces the same kind of tracking and mat-thickness inconsistency operators associate with alignment trouble on tracked pavers. Drive-wheel tire wear and hydrostatic wheel-motor seals are the other wheel-type-specific consumables; watch for hydraulic weeping at the wheel motors on higher-hour machines. Have your dealer verify tow-point and push-roller pivot wear if steering or tracking feels loose.
What burner or heating issues come up on the screed?
The screed heating circuit is prone to the same faults as any small fuel-fired burner: a low fuel supply, a fouled burner orifice, or a worn thermocouple or flame sensor causes a pilot that will not stay lit or a screed that heats unevenly bank to bank. Because the extension plates already lag the main plates in warm-up time, a partly working burner circuit compounds that lag and shows up as tearing behind the extenders on the first pass of the day. Cleaning the burner orifices and checking the fuel line for kinks or cracks resolves most no-heat complaints without replacing the burner assembly. Have your dealer verify burner ignition and thermocouple readings if one section of the screed will not reach temperature.
What should I check before buying a used BG-600D?
Walk it the way any used-paver inspection goes: check the instrument panel and seat condition, and look for excess rust or missing hardware as signs of poor upkeep. Pull the engine dipstick - clean oil is normal, but coolant on the dipstick means a blown head gasket and an expensive repair to price into the deal. Measure the screed at all four corners; a new plate runs about 12.7 mm (1/2 in) thick and 6.4 mm (1/4 in) remaining is still usable, but uneven thickness side to side signals the paver has been run out of alignment. Check the augers for damaged bearings, bent shafts, and thinned or pointed flighting, and look at the hopper wings - a bent wing with paint missing is a tell for rough handling. Because this is a hydrostatic machine, also check for hydraulic hose bulging or cracking at fittings and confirm the steering-angle and feed sensors are not throwing fault codes at start-up. Have your dealer run a full diagnostic scan and compare engine hours against paving-head hours before you close the deal.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific BG-600D part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.