Caterpillarasphalt paver
Caterpillar BG-240C
Maintenance schedule, common problems & OEM parts breakdown
The Cat BG-240C is a wheeled, mid-size highway-class asphalt paver from Caterpillar's Barber-Greene-derived BG C-series line. It runs a Cat 3116T turbocharged inline-6 diesel (6.6 L) rated about 114 kW (153-154 hp) gross and roughly 104 kW (139 hp) net, driving a closed-loop hydrostatic propel system with two-speed wheel motors and planetary final drives. Tractor-only operating weight runs approximately 14,445-14,830 kg (31,850-32,700 lb); full operating weight climbs toward 17,900-17,940 kg (39,350-39,550 lb) once a screed is mounted, so the final figure varies by screed configuration. Cat offered the BG-240C with either the power-extending Extend-A-Mat 10-20B screed (3.05-5.94 m paving width) or the fixed 3.05 m (10 ft) Pavemaster 10B screed. It succeeded the Barber-Greene BG-240B (same Extend-A-Mat 10-20B screed family, produced into the mid-1990s) as part of a C-series update Caterpillar rolled out across the BG-225C/230C/240C/245C/260C paver family after acquiring Barber-Greene's DeKalb paving operations in 1991; the same platform was also sold through Cat's own channel under the badge AP-900B.
The C-series update carried the 3116T engine plus shared driveline, hydraulic, and screed-heat components across the BG-225C/230C/240C/245C/260C family (the smaller BG-225C instead used the 3054 engine on a tracked chassis), so parts commonality runs wide across that generation. No direct BG-240D exists; Caterpillar's later D-series wheel pavers (BG-230D, BG-260D and the C7-ACERT-powered range) and the AP-1000-family absorbed the mid-size paving role the BG-240C filled, while the Barber-Greene 'BG' badge itself continued in Cat's lineup rather than disappearing outright. For today's used and parts market, that shared-platform lineage is the BG-240C's main value: it is a well-proven, mechanically-injected paver with broad parts interchange to its siblings and its AP-900B twin, still active on municipal and contractor fleets doing secondary and municipal paving work, though its pre-emissions 3116T limits its use in tightly regulated regions and keeps demand focused on cost-effective units and salvage parts rather than premium resale.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar BG-240C specifications
Engine
| Engine model | Cat 3116T, turbocharged inline 6-cylinder diesel, transverse-mounted |
| Cylinders | 6 |
| Gross power | 114 kW (153-154 hp) @ 2200 rpm |
| Net power | 104 kW (139 hp) @ 2200 rpm (per EEC 80/1269 and ISO 9249) |
| Displacement | 6.6 L (403 cu in) |
| Bore x stroke | 105 mm x 127 mm (4.12 in x 5.0 in) |
| Emissions | Meets EPA and CARB low-emissions engine regulations for its era; no Tier level or ECM fault-code system published for this model |
Weights
| Tractor only (no screed) | 14,445 kg (31,850 lb); some equipment databases list a slightly higher figure near 14,830 kg (32,695 lb) - treat as approximate, varies by source/serial range |
| With Extend-A-Mat 10-20B screed (+ truck hitch or push roller) | 17,900 kg (39,350 lb) |
| With Pavemaster 10B screed (+ truck hitch or push roller) | 16,300 kg (35,800 lb) |
| Ground pressure | not published for this rubber-tired paver |
Dimensions
| Length with push roller | Extend-A-Mat screed: 6.78 m (22 ft 3 in); Pavemaster screed: 6.29 m (20 ft 7 in) |
| Length with truck hitch | Extend-A-Mat screed: 7.26 m (23 ft 10 in); Pavemaster screed: 6.76 m (22 ft 2 in) |
| Operating/transport width | Extend-A-Mat screed: 3.33 m (10 ft 11 in); Pavemaster screed: 3.05 m (10 ft) |
| Transport width, hoppers raised | With end gates: 3.33 m (10 ft 11 in); without end gates: 3.05 m (10 ft) |
| Overall height | 3.38 m (11 ft 1 in) |
| Transport height (muffler removed) | 2.77 m (9 ft 1 in) |
| Wheelbase | 2.54 m (100 in) |
| Front wheel gauge | 2.49 m (98 in) |
| Rear wheel gauge | 2.28 m (90 in) |
| Inside turning radius | 2.9 m (9 ft 6 in) |
| Truck entry width | 3.2 m (10 ft 6 in) |
| Truck dump height | 0.62 m (24.5 in) |
| Auger diameter / height adjustment | 406 mm (16 in) diameter, hydraulically adjustable through 142 mm (5.6 in) of travel |
| Tires, drive (sand rib) | 18.00 x 25 |
| Tires, steering (solid rubber) | 406 mm x 559 mm (16 in x 22 in) |
Performance
| Travel speed, max | 16 km/h (10 mph) |
| Paving speed, max | 122 m/min (400 ft/min); drops to 69 m/min (225 ft/min) max when the optional front-wheel-assist package is fitted |
| Standard paving width | 3.05 m (10 ft), common to both screed options before extension |
| Paving range, Extend-A-Mat 10-20B screed | Power-extends 3.05-5.94 m (10 ft-19 ft 6 in); with cutoff shoes and extensions, 2.44-7.37 m (8 ft-24 ft 2 in) |
| Paving range, Pavemaster 10B screed | Fixed base width 3.05 m (10 ft); with cutoff shoes and extensions, 2.44-9.14 m (8 ft-30 ft) |
| Hopper capacity | 6.1 cu m (215 cu ft) |
| Drive system | Fully hydrostatic propel, dual-displacement wheel motors, separate propel circuit per drive wheel, single-speed planetary final drives with multi-disc parking brake |
| Steering | Full power steering through an automotive-type wheel; tandem articulated dual bogies each side |
| Gradeability | not published for this machine class |
Service capacities (summary)
| Fuel tank | 265 L (70 gal) |
| Hydraulic system | 189 L (50 gal) |
| Cooling system | 37 L (9.8 gal) |
| Engine oil | Not published in the factory spec sheet for this model; Cat 3116-family engines generally run 19-25 L (20-26 qt) depending on oil pan configuration - verify with dealer or service manual |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
BG-240C fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) - Cat 3116T diesel | approx. 19-25 L (20-26 qt), per 3116 engine family service data; exact BG-240C OMM figure not separately published online | Cat DEO or DEO-ULS diesel engine oil, API CH-4 or higher; SAE 15W-40 for warmer climates, SAE 10W-30 for wider cold-weather range per Cat climate-viscosity guidance |
| Cooling system | 37.1 L (9.8 US gal) | Cat ELC (Extended Life Coolant), premix or concentrate mixed with clean water; ELC rated for extended service (about 12,000 hours or 6 years); Cat DEAC (Diesel Engine Antifreeze/Coolant) is the standard-service alternative where ELC is not used |
| Fuel tank | 265.4 L (70.1 US gal) | No. 2-D diesel fuel, low or ultra-low sulfur per engine emissions configuration |
| Hydraulic system (tank plus circuit) | 189.3 L (50 US gal) | Cat HYDO Advanced 10 (SAE 10W) preferred for the hydraulic and hydrostatic drive circuits; acceptable alternates include Cat HYDO, Cat DEO 15W-40, Cat TDTO 10W, Cat MTO, or Cat TDTO-TMS depending on ambient temperature |
| Wheel drive / propel system | not separately documented for this wheel-type paver; propel is by hydrostatic wheel motors sharing the hydraulic system, not a distinct gearbox compartment | shares hydraulic system fluid (see hydraulic system row); verify with dealer if a separate wheel-hub gear compartment applies to a given serial range |
| Grease (all fittings) | spec only, no chart total given | Cat Multipurpose Grease (Cat MPGM), NLGI 2; Cat Arctic Platinum grease for extreme cold climates |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar BG-240C maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
Servicing the BG-240C beyond the schedule
Predictive Maintenance & Fluid Analysis
Run oil sampling on the 3116T every 250-500 hours to catch injector and turbo wear before it strands the paver mid-mat. Trend hydraulic oil condition on the propel and screed-extension circuits, since contamination there shows up first as erratic screed width or feed-rate hunting. Sample auger gearbox oil for metal content to flag bearing wear early, and check coolant condition each interval -- this engine has no aftertreatment to mask a cooling problem.
Corrective & Common Repairs
Screed heater elements and thermostats are the most frequent callback on the BG-240C, especially on Extend-A-Mat units with more heat zones to fail. Auger and conveyor gearbox seals weep after chain-tension neglect lets shaft loads climb, and stretched drive chains show up as inconsistent mat feed before they show up as broken links. Tamper bar bushing wear telegraphs into mat texture defects. Mechanical injectors and fuel filters foul faster than modern electronic engines on marginal fuel, so filter changes are the cheapest insurance on this engine.
Overhaul & Rebuild Points
High-hour BG-240C units commonly need a 3116T top-end rebuild -- liners, injectors, turbocharger -- once oil-analysis trends turn, since this pre-electronic engine gives no fault codes to warn you first. Auger and conveyor gearboxes are common rebuild candidates after years of aggregate exposure, as are the propel pump and drive motors. Screed extension slides and wear strips need replacement to hold mat-width accuracy on the Extend-A-Mat 10-20B, and wheeled undercarriage spindles and bearings deserve inspection at any major overhaul.
Seasonal & Environment Servicing
Before paving season, cycle the screed heater system fully and check every element and thermostat zone -- a cold screed on day one tears the mat. Cold-start the 3116T with its starting aid and check coolant freeze point and hydraulic oil grade for winter viscosity. In hot, dusty paving conditions shorten auger and conveyor chain lube intervals, and keep hydraulic hoses and screed wiring routed clear of hot asphalt and abrasive fines that shorten their life.
BG-240C common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 112-6523 | Insert-Fuel Filter | Fuel system service | Check fitment → |
| 119-0073 | Filter Element-Fuel | Fuel system service | Check fitment → |
| 6I-2499 | Filter Element As-Air | Air intake service | Check fitment → |
| 6I-2500 | Filter Element As-Air | Air intake service | Check fitment → |
| 077-5232 | Filter Element-Breather | Hydraulic service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
BG-240C fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| Engine Oil Pressure warning lamp (red) — generic Cat convention CID 100 | Engine oil pressure has dropped below the safe operating range for current engine speed, sensed by a pressure switch/sender rather than a stored ECM fault code | Low oil level, worn oil pump, plugged oil filter, or a failed pressure sender/switch | Stop the engine immediately, check oil level and filter condition before restarting |
| Coolant Temperature warning lamp (red) — generic Cat convention CID 110 | Engine coolant temperature has risen above the normal operating range | Low coolant level, slipping or broken fan belt, blocked radiator core, or failed thermostat | Idle the engine, let it cool, then check coolant level, fan belt tension, and radiator fins before continuing work |
| Low Coolant Level warning lamp — generic Cat convention CID 111 | Coolant level probe in the top tank or recovery bottle reads below minimum | External or internal coolant leak, loose hose clamp, failed radiator cap, or head gasket seepage | Stop and inspect for leaks, top off with the specified coolant mix, pressure-test the cooling system if level keeps dropping |
| Charging System warning lamp (amber/red) — generic Cat convention CID 168 | Alternator output or system voltage is below/above normal | Slipping or broken alternator belt, failed alternator or regulator, or loose/corroded battery connections | Check belt condition and tension and battery cable connections, then test alternator output |
| Air Cleaner Restriction indicator | Intake air filter restriction has exceeded the allowable vacuum limit | Clogged primary air filter element from dust/asphalt fines | Service or replace the air filter element and reset the restriction indicator |
| Hydraulic Oil Temperature warning lamp | Hydraulic tank fluid temperature has exceeded the normal operating range | Low hydraulic fluid level, blocked oil cooler fins, or sustained high-load operation in hot ambient conditions | Idle the machine, check fluid level, and clear any debris from the oil cooler core |
| Hydraulic Filter Restriction (bypass) indicator | Return-line hydraulic filter element is loaded enough to approach bypass | Contaminated filter element or cold/high-viscosity fluid on startup | Replace the hydraulic return filter element |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
BG-240C attachments & work tools
Screed family (fixed-width)
Pavemaster 10B screed is the base fixed-width unit for this class, standard paving width 3.05 m (10 ft), heavy-duty frame accepts cutoff shoes and bolt-on extensions for occasional wider passes up to 9.14 m (30 ft).
Screed family (power-extending)
Extend-A-Mat 10-20B screed is the wider-capacity option for this class: hydraulically power-extends from 3.05 m (10 ft) to 5.94 m (19 ft 6 in), with cutoff shoes and bolt-on extensions reaching up to 7.37 m (24 ft 2 in) for occasional extra-wide work.
Screed heating
Screeds of this generation use a diesel-fired heat system (dedicated screed heat wiring/burner group) to bring plates to paving temperature, rather than the electric plate-heating used on later Cat SE-series screeds. Confirm heater type against the specific screed serial before ordering heat-system parts.
Material handling (feeders/augers)
Twin hydrostatically driven feeder augers move mix from the hopper to the screed, each fed by an independently adjustable feeder gate so the operator can meter material flow to match paving width and mix head. Auger sections/extensions are matched to whichever screed width is fitted, not a separate universal kit.
Screed mounting / coupling
The screed bolts and pins to the tractor's leveling arms and tow-point hitch; there is no universal quick-coupler as on skid-steer tools. Arm length and hitch geometry are matched to the specific screed model, so screeds are paired rather than freely interchanged across paver models.
Bolt-on width extensions
Beyond hydraulic extension range, both screed options accept bolt-on extension sections for occasional extra-wide passes; this is standard practice across Cat's 3.0 m-class screed-frame family rather than a BG-240C-specific option.
Operator station guarding
An operator platform canopy/ROPS structure is offered over the station as a factory safety configuration for this paver class, protecting the operator position without altering paving function.
All BG-240C assemblies by section
Every catalogued assembly group for the Caterpillar BG-240C. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
6i-2551 Air Cleaner Gp
| 6I***99 | Filter Element As-Air; (Primary) | 1 |
| 6I***00 | Filter Element As-Air; (Secondary) | 1 |
| 6I***51 | Air Cleaner Group | 1 |
176-9175 Air Cleaner Gp
| 10***01 | Adapter As | 1 |
| 11***33 | Bracket | 2 |
| 12***46 | Precleaner Group | 1 |
142-0333 Exhaust Gp
| 10***70 | Elbow-Exhaust | 1 |
| 10***25 | Coupling-Exhaust | 1 |
| 11***89 | Muffler | 1 |
7w-9248 Manifold Gp-Exhaust
| 10***38 | Manifold-Exhaust | 1 |
| 11***00 | Gasket-Manifold | 3 |
| 14***48 | Bolt; (M10x1.5x65-mm)(M10x1.50x65mm) | 12 |
159-8603 Manifold Gp-Inlet
| 11***50 | Gasket | 1 |
| 15***03 | Manifold Group-Inlet | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
121-7746 Precleaner Gp
| 12***46 | Precleaner Group | 1 |
| 13***43 | Clamp-Hose | 1 |
| 1M***50 | Bowl | 1 |
129-1148 Turbocharger Gp
| 12***23 | Turbocharger Group | 1 |
| 12***48 | Turbocharger Group | 1 |
| 3E***17 | Locknut; (M10x1.5-Thd)(Spiralock) | 4 |
125-1123 Turbocharger Gp
| 10***77 | Housing | 1 |
| 10***64 | Cartridge Group-Turbocharger | 1 |
| 12***23 | Turbocharger Group | 1 |
Basic Engine
108-5759 Camshaft Gp
| 10***94 | Plate-Thrust | 1 |
| 10***59 | Camshaft Group; (Single) | 1 |
| 13***76 | Camshaft Assem. | 1 |
4w-3462 Carrier Gp-Seal
| 23***83 | Gasket | 1 |
| 24***76 | Seal | 1 |
| 2W***46 | Cover | 1 |
103-0863 Cover Gp-Cylinder Block
| 10***63 | Cover Group-Cylinder Block | 1 |
| 11***18 | Bolt As; (M8x1.25x16-mm) | 4 |
| 1U***46 | Sealant (For Locations A) | 0 |
7l-0004 Cover Gp-Front Housing
| 10***20 | Cover As-Front | 1 |
| 13***19 | Seal-Integral; (Integral) | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
4w-2172 Cover Gp-Valve Mechanism
| 11***40 | Gasket; (Valve Cover) | 1 |
| 11***60 | Cover | 1 |
| 4W***72 | Cover Group-Valve Mechanism; Valve Mechanism Cover Group | 1 |
4w-2197 Crankshaft Gp
| 10***08 | Bearing-Main; (Standard) | 6 |
| 14***62 | Bearing; (0.25mm Undersize) | 0 |
| 14***64 | Bearing; (0.5mm Undersize) | 0 |
149-5403 Cylinder Block Gp
| 14***02 | Pin, Cylinder Block As | 1 |
| 14***03 | Cylinder Block Group | 1 |
| 21***86 | Bearing-Sleeve; (Camshaft) | 1 |
7e-2482 Cylinder Block Gp
| 14***03 | Cylinder Block Group | 1 |
| 1W***07 | Sleeve | 2 |
| 4P***51 | Tube As-Piston Cooling | 6 |
140-7373 Cylinder Head As
| 11***36 | Seal-Valve Stem | 12 |
| 14***73 | Cylinder Head As | 1 |
| 19***66 | Cylinder Head As | 1 |
190-9066 Cylinder Head As
| 11***61 | Sleeve | 6 |
| 16***63 | Insert-Valve Seat; (Inlet) | 6 |
| 19***66 | Cylinder Head As | 1 |
140-7371 Cylinder Head Gp
| 11***36 | Seal-Valve Stem | 12 |
| 13***19 | Valve-Exhaust | 6 |
| 14***71 | Cylinder Head Group | 1 |
160-5130 Cylinder Head Gp
| 14***71 | Cylinder Head Group | 1 |
| 16***30 | Cylinder Head Group | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 3 |
159-0305 Cylinder Head Gp
| 10***32 | Gasket; (1.61mm Thk) | 1 |
| 12***36 | Bolt-Hex Head; (M20x2.5x160mm) | 14 |
| 14***71 | Cylinder Head Group | 1 |
4p-2844 Damper & Pulley Gp
| 20***88 | Damper Assem. | 1 |
| 4P***43 | Pulley | 1 |
| 4P***44 | Damper & Pulley Group | 1 |
136-8877 Drain Gp-Engine Oil
| 13***77 | Drain Group-Engine Oil | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 6V***38 | Valve-Shutoff; (Engine Oil Pan Drain) | 1 |
108-5434 Drive Gp-Accessory
| 10***60 | Adapter-Pump | 1 |
| 10***34 | Drive Group-Accessory | 1 |
| 13***19 | Seal-Integral; (Integral) | 1 |
7c-0044 Drive Gp-Fan
| 4W***03 | Cup-Roller Bearing | 2 |
| 4W***04 | Cone-Roller Bearing | 2 |
| 4W***42 | Spacer; (35.3x45.5x38.331-mm Thk) | 1 |
163-9473 Drive Gp-Pump
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 07***82 | Seal | 1 |
| 07***06 | Coupling | 1 |
161-1245 Drive Gp-Pump
| 10***33 | . Pedestal, Flange-Nylon | 1 |
| 16***45 | Drive Group-Pump | 1 |
| 18***15 | Drive Group-Pump | 1 |
187-8715 Drive Gp-Pump
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 07***06 | Coupling | 1 |
| 07***13 | Sleeve | 2 |
4w-5428 Drive Gp-Water Pump
| 03***75 | V-Belt; (Pump Drive)(Water) | 1 |
| 10***67 | Plate As-Idler | 1 |
| 11***04 | Pulley As-Idler | 1 |
9y-2755 Flywheel Gp
| 1W***64 | Gear-Flywheel Ring; (126-Teeth) | 1 |
| 20***82 | Flywheel As | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 8 |
101-4540 Gear Gp-Front
| 10***07 | Shaft-Cam Idler | 1 |
| 10***08 | Plate-Retaining | 1 |
| 10***40 | Gear Group-Front | 1 |
7w-8813 Housing Gp-Flywheel
| 2P***94 | Plug-Sealing | 1 |
| 6V***42 | Bolt (M10x1.50x40mm) | 2 |
| 7C***33 | Housing-Flywheel | 1 |
101-4539 Housing Gp-Front
| 10***39 | Housing Group-Front | 1 |
| 10***11 | Plug | 2 |
| 13***42 | Housing-Front | 1 |
4w-2515 Lifting Gp-Engine
| 4W***82 | Plate-Lifting; (Rear)(Rear) | 1 |
| 4W***83 | Plate-Lifting; (Front) | 1 |
| 4W***15 | Lifting Group | 1 |
119-5977 Mounting Gp-Engine Flexible
| 10***20 | Mount As | 1 |
| 11***62 | Mount As | 1 |
| 11***77 | Mounting Group-Engine Flexible | 1 |
4p-1723 Pan Gp-Oil -Engine
| 11***70 | Pan As-Oil; (Engine) | 1 |
| 21***46 | Bolt As; (M8x1.25x18-mm) | 36 |
| 26***16 | Gasket-Oil Pan; (Engine) | 1 |
107-7639 Piston & Rod Gp
| 10***45 | Crown As-Piston | 1 |
| 10***39 | Piston & Rod Group; Connecting Rod And Piston Group | 1 |
| 10***87 | Ring-Piston (Top-Chrome) | 1 |
4w-5429 Pulley Gp-Crankshaft
| 2W***81 | Plate-Clamp; (Pulley Clamp) | 1 |
| 4W***29 | Pulley Group-Crankshaft; Crankshaft Pulley Group | 1 |
| 7W***73 | Pulley-Crankshaft; (1-Groove) | 1 |
9y-0757 Pulley Gp-Fan Drive
| 7C***90 | Pulley-Fan Drive | 1 |
| 8T***08 | Bolt (M8x1.25x25mm); (M8x1.25x25-mm) | 6 |
| 9Y***57 | Pulley Group-Fan Drive | 1 |
107-7722 Rocker Arm Gp
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 1 |
| 10***91 | Seat-Wear | 1 |
| 10***76 | Rocker Arm As; (Unit Injector) | 1 |
115-4203 Seal Gp-Crankshaft
| 11***03 | Seal Group-Crankshaft | 1 |
| 22***09 | Seal Group-Crankshaft; (Rear) | 1 |
| 24***39 | Seal-Crankshaft; (Front)(Front) | 1 |
4p-4372 Mechanism Gp-Fuel Pump & Valve
| 10***22 | Rocker Arm Group-Valve | 6 |
| 14***47 | Arm As-Lifter | 4 |
| 2D***42 | Ball 6.35 mm(.25 In.)Diameter | 2 |
Braking System
192-7472 Brake Gp-Parking
| 11***28 | Kit-Seal; (Final Drive Planetary) | 1 |
| 11***29 | Kit-Brake Lining; (Final Drive Planetary) | 1 |
| 12***65 | Kit-Brake Spring; (Final Drive Planetary) | 1 |
162-7444 Lines Gp-Parking Brake
| 11***39 | Hose As | 1 |
| 11***75 | Valve-Needle | 1 |
| 11***01 | Hose As | 1 |
Controls
185-4044 Jack Gp-Height Adjuster
| 18***65 | Jack Group-Height Adjuster | 1 |
| 18***44 | Jack Group-Height Adjuster | 1 |
| 1F***50 | Nut Rops Support | 1 |
Cooling System
100-6269 Cooler Gp-Engine Oil
| 10***69 | Cooler Group-Engine Oil | 1 |
| 23***55 | Gasket | 1 |
| 26***43 | Core As-Engine Oil Cooler | 1 |
121-2749 Cooling Gp-Supplemental
| 10***76 | Hose-Upper; (Radiator)(Radiator) | 1 |
| 11***28 | Hose-Lower; (Radiator)(Radiator) | 1 |
| 12***42 | Mount As | 1 |
7c-9048 Lines Gp-Water
| 12***47 | Housing-Water Regulating | 1 |
| 12***69 | Regulator-Water Temperature; (94-Deg C) | 1 |
| 12***71 | Clamp-Hose | 2 |
159-3137 Pump Gp-Water
| 14***88 | Seal As; (Water Pump) | 1 |
| 15***52 | Impeller-Pump | 1 |
| 15***37 | Pump Group-Water | 1 |
7c-4508 Pump Gp-Water
| 15***37 | Pump Group-Water | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
4w-7589 Pump Gp-Water
| 2M***53 | Seal--To Seal Brake Housing To Main Housing | 1 |
| 4J***24 | Seal 46.99 mm(1.85 In.) I.D. | 1 |
| 4W***89 | Pump Group-Water | 1 |
171-9705 Radiator Gp
| 03***64 | Cap As-Radiator; (7-Psi) | 1 |
| 17***05 | Radiator Group | 1 |
| 18***36 | Shroud | 1 |
Electrical And Starting System
244-1090 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 18***33 | Pin-Connector; (16-Ga To 18-Ga) | 1 |
| 24***90 | Alarm Group; -Backup | 1 |
9w-3043 Alternator Gp-Charging
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 5 |
| 10***63 | Regulator As-Alternator; (24-Volt) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
9y-8187 Alternator Gp-Charging
| 4N***05 | Spacer; (0.42x0.75x0.6-In Thk) | 1 |
| 7C***63 | Bracket-Alternator | 1 |
| 7C***29 | Pulley-Alternator | 1 |
183-9629 Battery Gp
| 03***07 | Terminal-Ring; (0-Ga, 3/8-In Screw) | 1 |
| 10***58 | Bracket As-Battery | 1 |
| 11***37 | Cable As | 1 |
175-7737 Box Gp-Junction
| 17***82 | Film-Warning; (High Voltage) | 1 |
| 17***83 | Film-Identification; (Electrical Outlet) | 1 |
| 17***37 | Box Group-Junction | 1 |
161-3586 Box Gp-Junction
| 03***38 | Screw; (6-32x1.0in) | 4 |
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 10***23 | Board-Control | 2 |
213-8137 Box Gp-Junction
| 03***38 | Screw; (6-32x1.0in) | 4 |
| 03***49 | Nut-Self Lock; (No.10.Unc) | 2 |
| 10***23 | Board-Control | 2 |
175-7736 Box Gp-Junction
| 17***82 | Film-Warning; (High Voltage) | 1 |
| 17***83 | Film-Identification; (Electrical Outlet) | 1 |
| 17***36 | Box Group-Junction | 1 |
164-7359 Cover Gp-Wiring Harness
| 16***59 | Cover Group-Wiring Harness | 1 |
| 17***96 | Bracket-Mounting | 1 |
| 17***97 | Flange | 1 |
160-7092 Electrical Ar
| 10***54 | Horn & Alarm Group | 1 |
| 16***92 | Electrical Ar | 1 |
| 16***80 | Installation Group-Controls | 1 |
160-4233 Generator Gp-Hydraulic -8 Kilowatt
| 16***33 | Generator Group-Hydraulic; -8 Kilowatt | 1 |
| 17***42 | Ring-Slip | 1 |
| 17***44 | Fan | 1 |
180-9474 Generator Gp-Hydraulic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***50 | Sleeve; (32-cm) | 0 |
| 10***04 | Suppressor As-Arc | 1 |
190-4165 Generator Gp-Hydraulic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***50 | Sleeve; (32-cm) | 0 |
| 10***04 | Suppressor As-Arc | 1 |
166-4141 Generator Gp-Hydraulic -6 Kilowatt
| 16***41 | Generator Group-Hydraulic; -6 Kilowatt | 1 |
| 17***42 | Ring-Slip | 1 |
| 17***43 | Rotor | 1 |
219-6313 Generator Gp-Hydraulic -8 Kilowatt
| 17***44 | Fan | 1 |
| 17***45 | Support | 2 |
| 17***46 | Brush | 6 |
219-6308 Generator Gp-Hydraulic -6 Kilowatt
| 17***44 | Fan | 1 |
| 17***45 | Support | 2 |
| 17***46 | Brush | 6 |
163-1680 Installation Gp-Controls
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
9x-1439 Lamp Gp-Flood
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 1 |
| 8T***33 | Nut (M10x1.50 Thd) | 1 |
110-7563 Lamp Gp-Warning Beacon -Strobe Light
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***63 | Lamp Group-Warning Beacon; -Strobe Light | 1 |
| 12***58 | Tube-Flash; (3 Prong Connection)(Warning Beacon) | 1 |
116-8711 Lamp Gp-Warning Beacon
| 03***14 | Screw; (10-32x1-In) | 3 |
| 11***63 | Lamp Group-Warning Beacon; -Strobe Light | 1 |
| 11***11 | Lamp Group-Warning Beacon | 1 |
116-8703 Lighting Gp-Flood
| 10***99 | Harness As-Lighting; (Floodlights)(Rear) | 4 |
| 10***29 | Plate | 2 |
| 11***03 | Lighting Group-Flood | 1 |
160-7395 Module Gp-Timer
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 16***95 | Module Group-Timer; -Governor Control | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 5 |
170-7071 Motor Gp-Electric
| 09***47 | Brush As | 1 |
| 11***94 | Bell; (Rear) | 1 |
| 11***61 | Bearing | 2 |
164-0814 Mounting Gp-Wiring
| 11***18 | Clip | 2 |
| 11***66 | Mount | 1 |
| 16***14 | Mounting Group-Wiring | 1 |
106-9703 Sensor Gp-Auger
| 10***28 | Clamp | 2 |
| 10***03 | Sensor Group-Auger | 1 |
| 10***66 | Sensor As-Sonic; (Mat'L Flow) | 2 |
104-6600 Sensor Gp-Auger
| 10***00 | Sensor Group-Auger | 1 |
| 10***91 | Support As | 2 |
| 10***92 | Sensor Group-Position; -Auger | 2 |
109-0192 Sensor Gp-Position -Auger
| 10***92 | Sensor Group-Position; -Auger | 1 |
| 15***54 | Cable | 1 |
| 3H***94 | Setscrew-Socket | 2 |
284-8876 Sensor Gp-Position
| 22***22 | Kit-Hub; (Grade Sensor) | 1 |
| 28***76 | Sensor Group-Position | 1 |
| 3B***08 | Lockwasher Handrails To Dash | 1 |
189-5746 Sensor Gp-Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***36 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 17***49 | Strap; (Marker) | 1 |
7c-9458 Solenoid Gp-Shutoff
| 12***72 | Solenoid As; (Fuel Shutoff) | 1 |
| 4K***88 | Seal; Adapter To Oil Pump Outlet Manifold | 1 |
| 6V***77 | Nut (8-32 Thd) | 2 |
160-7396 Solenoid Gp-Throttle -Governor
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***96 | Solenoid Group-Throttle; -Governor | 1 |
| 8T***29 | Pin-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 2 |
102-8823 Starting Aid Gp
| 10***58 | Cover-Inlet Manifold | 1 |
| 10***62 | Elbow | 1 |
| 10***23 | Starting Aid Group; (Heater) | 1 |
104-7040 Starting Motor Gp-Electric
| 10***40 | Starting Motor Group-Electric | 1 |
| 10***57 | Starting Motor Group-Electric; Electric Starting Motor Group (Robert Bosch) | 1 |
| 6V***20 | Starting Motor Group-Electric; (Electric) | 1 |
106-8558 Starting Motor Gp-Electric
| 10***58 | Starting Motor Group-Electric | 1 |
| 10***59 | Starting Motor Group-Electric; Electric Starting Motor Group (Delco Remy) | 1 |
106-8559 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
207-1517 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
| 10***49 | Housing As-Starter | 1 |
207-1511 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
| 10***49 | Housing As-Starter | 1 |
108-3858 Starting Motor Gp-Electric
| 10***58 | Starting Motor Group-Electric | 1 |
| 11***73 | Bolt-12 Point Head; (M10x1.5x35-mm) | 3 |
| 13***30 | Wire As | 1 |
6v-5720 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
159-7919 Starting Motor Gp-Electric
| 10***40 | Starting Motor Group-Electric | 1 |
| 10***08 | Bolt (M10x1.5x35mm); (M10x1.5x35-mm) | 3 |
| 15***19 | Starting Motor Group-Electric | 1 |
106-8557 Starting Motor Gp-Electric
| 10***57 | Starting Motor Group-Electric; Electric Starting Motor Group (Robert Bosch) | 1 |
| 7X***62 | Washer-Hard; (13.5x19x0.8-mm Thk) | 3 |
| 8F***34 | Lockwasher; (External Teeth) | 1 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
172-8660 Switch Gp-Liquid Level
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***60 | Switch Group-Liquid Level; -Rear Engine Oil-Ster, Hydraulic Fan Oil-Engine On-Steering Oil, Engine Off-Auxiliary Coolant-Front Engine Oil-Brake Oil, Hoist-Engine Coolant-Tc Oil-Low, Cold | 1 |
| 9X***01 | Pin-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 2 |
9g-7641 Switch Gp-Start -Engine, Key
| 6V***62 | Screw-Machine; (8-32x0.31-In) | 4 |
| 7T***99 | Nut-Mounting; (1-32-Thd) | 1 |
| 9B***33 | Lockwasher; (Int'L Tooth) | 4 |
164-6261 Wiring Gp-Engine
| 11***34 | Film-Information; (Main, Circuit Breaker)(Main) | 1 |
| 11***35 | Film-Information; (Engine, Circuit Breaker) | 1 |
| 11***34 | Switch Group-Magnetic; -Start Relay | 2 |
198-1316 Wiring Gp-Engine
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Suppressor As-Arc | 1 |
165-4513 Wiring Gp-Machine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***62 | Screw-Machine; (4-40x0.63-In) | 4 |
| 10***51 | Plug | 1 |
Engine Arrangement
161-1242 Engine Ar
| 11***77 | Mounting Group-Engine Flexible | 1 |
| 12***49 | Cooling Group-Supplemental | 1 |
| 14***33 | Exhaust Group | 1 |
159-6000 Engine Ar
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***39 | Housing Group-Front | 1 |
| 10***40 | Gear Group-Front | 1 |
161-1244 Engine Ar
| 09***61 | Strap; (Cable) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
Feeder Drag And Auger Conveyors
102-6331 Actuator Gp-Power
| 10***31 | Actuator Group-Power; -Custom | 1 |
| 11***29 | Kit-Seal; (Power Actuator) | 1 |
| 11***81 | Kit-Gear; (Power Actuator) | 1 |
116-9509 Bearing Gp-Auger
| 10***04 | Nipple-Pipe | 1 |
| 10***18 | Bearing Group-Auger | 1 |
| 11***09 | Bearing Group-Auger | 1 |
106-9717 Bearing Gp-Auger
| 10***17 | Bearing Group-Auger | 1 |
| 11***94 | Bearing-Insert | 1 |
| 19***77 | Shield | 1 |
106-9718 Bearing Gp-Auger
| 01***41 | Setscrew-Socket | 3 |
| 10***18 | Bearing Group-Auger | 1 |
| 3H***40 | Setscrew; (3/8-24x0.375-In) | 2 |
201-5584 Bearing Gp-Auger
| 11***94 | Bearing-Insert | 1 |
| 20***83 | Cap | 2 |
| 20***84 | Bearing Group-Auger | 1 |
119-6652 Chain Gp-Conveyor
| 11***52 | Chain Group-Conveyor | 1 |
| 11***53 | Chain Group-Conveyor; -Rh | 1 |
| 13***32 | Chain Group-Conveyor; -Lh | 1 |
119-6653 Chain Gp-Conveyor -Rh
| 11***53 | Chain Group-Conveyor; -Rh | 1 |
| 8I***14 | Bar-Side | 61 |
| 8I***15 | Bar-Side | 31 |
134-6432 Chain Gp-Conveyor -Lh
| 13***32 | Chain Group-Conveyor; -Lh | 1 |
| 8I***14 | Bar-Side | 61 |
| 8I***15 | Bar-Side | 31 |
115-8326 Conveyor Ar-Drag & Auger
| 10***77 | Footshaft Group | 2 |
| 11***26 | Conveyor Ar-Drag & Auger | 1 |
| 11***44 | Shaft Group-Feeder Drive | 2 |
144-5418 Conveyor Gp-Auger
| 06***66 | Bolt; (3/4-10x1.642-In) | 6 |
| 07***87 | Ring-Retaining | 4 |
| 10***55 | Plate | 1 |
230-1538 Conveyor Gp-Auger
| 06***66 | Bolt; (3/4-10x1.642-In) | 6 |
| 10***55 | Plate | 1 |
| 10***57 | Slide As | 1 |
115-8346 Conveyor Gp-Drag
| 05***20 | Pin-Spring | 60 |
| 11***46 | Conveyor Group-Drag | 1 |
| 11***52 | Chain Group-Conveyor | 1 |
8i-0852 Drive Gp-Conveyor -Drag Conveyor
| 03***60 | Cup-Roller Bearing | 1 |
| 03***61 | Cone-Roller Bearing | 1 |
| 08***43 | Gear-Cluster | 3 |
185-0787 Drive Gp-Conveyor -Auger Conveyor
| 08***41 | Carrier As | 1 |
| 08***44 | Gear-Input | 1 |
| 08***83 | Washer; (Thrust) | 1 |
1g-9347 Extension Gp-Auger -6 In
| 1G***47 | Extension Group-Auger; -6 In | 1 |
| 1G***48 | Tube | 2 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 2 |
5e-9826 Extension Gp-Auger -2-Ft, Rh
| 08***53 | Shaft-Governor Control | 1 |
| 1K***72 | Locknut Horn To Guard | 4 |
| 5E***26 | Extension Group-Auger; -2-Ft, Rh | 1 |
5e-9825 Extension Gp-Auger -2-Ft, Lh
| 08***53 | Shaft-Governor Control | 1 |
| 1K***72 | Locknut Horn To Guard | 4 |
| 5E***25 | Extension Group-Auger; -2-Ft, Lh | 1 |
5e-9809 Extension Gp-Auger -1-Ft, Rh
| 08***53 | Shaft-Governor Control | 1 |
| 1K***72 | Locknut Horn To Guard | 2 |
| 5E***09 | Extension Group-Auger; -1-Ft, Rh | 1 |
5e-9808 Extension Gp-Auger -1-Ft, Lh
| 08***53 | Shaft-Governor Control | 1 |
| 1K***72 | Locknut Horn To Guard | 2 |
| 5E***08 | Extension Group-Auger; -1-Ft, Lh | 1 |
104-7477 Footshaft Gp
| 00***54 | Cup-Roller Bearing | 4 |
| 06***92 | Washer | 2 |
| 10***35 | Cone As-Bearing | 4 |
163-3217 Gate Gp-Feeder
| 03***91 | Pop - Rivet (To Secure Safety Lable) | 2 |
| 10***31 | Actuator Group-Power; -Custom | 2 |
| 11***33 | Pin | 2 |
115-8347 Guard Gp-Feeder
| 03***82 | Screw; (3/8-16x2-In) | 12 |
| 10***41 | Plate | 2 |
| 11***47 | Guard Group-Feeder | 1 |
115-8336 Lines Gp-Lubrication
| 10***01 | Tube As | 1 |
| 11***36 | Lines Group-Lubrication | 1 |
| 12***88 | Tube As | 2 |
227-8946 Shaft Gp-Feeder Drive
| 03***21 | Bolt-Allen Hd; (3/8unc X 1) | 4 |
| 10***30 | Bearing-Flange | 1 |
| 10***70 | Key-Square | 1 |
115-8344 Shaft Gp-Feeder Drive
| 03***21 | Bolt-Allen Hd; (3/8unc X 1) | 4 |
| 10***30 | Bearing-Flange | 1 |
| 10***70 | Key-Square | 1 |
Frame And Body
115-8343 Arm Gp-Tow
| 03***83 | Spacer | 16 |
| 03***53 | Ring-Retaining | 2 |
| 05***74 | Pin | 2 |
106-9689 Brace Gp
| 10***89 | Brace Group | 1 |
| 10***62 | Tube As-Brace | 1 |
| 10***64 | Tube As-Brace | 1 |
122-5897 Brace Gp
| 10***81 | Tube As; -Ski Tow | 1 |
| 10***89 | Brace Group | 1 |
| 12***97 | Brace Group | 1 |
109-2722 Bracket Gp-Support
| 06***66 | Bolt; (3/4-10x1.642-In) | 2 |
| 10***22 | Bracket Group-Support | 1 |
| 11***52 | Plate | 1 |
167-0699 Cover Gp-Engine & Platform
| 03***71 | Capscrew, Csk. Hd., 3/8in.-16 N.C. X 1in. | 8 |
| 03***72 | Bolt; (3/8-16-Thd) | 11 |
| 10***03 | Panel; (N.S.) | 2 |
147-8340 Cover Gp-Paver Ventilation -Without Generator
| 11***62 | Washer | 4 |
| 14***47 | Plate-Cover | 1 |
| 14***40 | Cover Group-Paver Ventilation; -Without Generator | 1 |
215-7553 Extension Gp-Main Frame
| 20***86 | Pin | 4 |
| 21***50 | Bracket As; (Lh) | 1 |
| 21***51 | Bracket As; (Rh) | 1 |
106-9714 Extension Gp-Main Frame -1 Ft
| 10***14 | Extension Group-Main Frame; -1 Ft | 1 |
| 10***88 | Extension As | 1 |
| 7X***45 | Bolt 5/8" X 1 3/4" Long (First Type) | 3 |
106-9715 Extension Gp-Main Frame -2 Ft
| 10***15 | Extension Group-Main Frame; -2 Ft | 1 |
| 10***90 | Extension As | 1 |
| 7X***45 | Bolt 5/8" X 1 3/4" Long (First Type) | 3 |
163-1211 Frame As
| 10***83 | Screw-Flat Head; (1/2-13x1-In) | 2 |
| 16***11 | Frame As | 1 |
| 16***86 | Tube | 4 |
222-1813 Frame As
| 10***83 | Screw-Flat Head; (1/2-13x1-In) | 2 |
| 11***52 | Frame As | 1 |
| 16***86 | Tube | 4 |
168-0232 Guard Gp-Deflector
| 16***99 | Guard; (Lh) | 1 |
| 16***00 | Guard; (Rh) | 1 |
| 16***09 | Deflector | 1 |
104-6579 Guide Gp-Steering
| 03***74 | Keeper | 1 |
| 10***79 | Guide Group-Steering | 1 |
| 10***39 | Tube As | 1 |
169-9539 Hopper Gp
| 03***71 | Capscrew, Csk. Hd., 3/8in.-16 N.C. X 1in. | 2 |
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 2 |
| 10***15 | Apron As | 2 |
172-1234 Installation Ar-Ventilation
| 14***81 | Ventilation Group-Paver; -Without Generator | 1 |
| 17***80 | Lines Group-Paver Ventilation | 1 |
| 17***34 | Installation Ar-Ventilation | 1 |
173-7690 Kit-Hopper
| 10***42 | Spacer; (13.8x23.75x12.7-mm Thk) | 2 |
| 16***85 | Pin As | 2 |
| 16***86 | Tube | 8 |
118-7295 Step Gp
| 11***15 | Step As | 1 |
| 11***34 | Bracket As; (Rh) | 1 |
| 11***03 | Bracket As; (Lh) | 1 |
163-1675 Structural Ar
| 10***79 | Guide Group-Steering | 1 |
| 10***68 | Support Group-Tow Arm | 1 |
| 10***70 | Platform Group | 1 |
169-5471 Support Gp-Frame
| 10***89 | Brace Group | 1 |
| 10***22 | Bracket Group-Support | 1 |
| 16***71 | Support Group-Frame | 1 |
104-7468 Support Gp-Tow Arm
| 06***35 | Lock Pin | 2 |
| 10***68 | Support Group-Tow Arm | 1 |
| 10***37 | Lever As | 1 |
147-6981 Ventilation Gp-Paver -Without Generator
| 11***62 | Washer | 5 |
| 14***00 | Inlet-Blower | 1 |
| 14***95 | Hose; (650-cm Each) | 0 |
Fuel System
129-1102 Base Gp-Fuel Filter
| 11***23 | Insert-Fuel Filter | 1 |
| 12***01 | Valve Group-Check; -Fuel-Fuel Filter | 1 |
| 12***02 | Base Group-Fuel Filter | 1 |
164-4858 Cap Gp-Fuel Filler -Extreme Service, Lockable
| 16***58 | Cap Group-Fuel Filler; -Extreme Service, Lockable | 1 |
| 19***75 | Cover As-Filter; (Fuel Cap) | 1 |
| 9X***00 | Seal-O-Ring | 1 |
105-1695 Control Gp-Fuel Injection
| 10***95 | Control Group-Fuel Injection | 1 |
| 16***56 | Control Group-Fuel Injection | 1 |
| 6V***83 | Bolt (16mm Long); (M6x1x16-mm) | 4 |
7e-9429 Control Gp-Governor
| 5C***53 | Bolt (M6x1.00x16mm); (M6x1x16mm Thk) | 1 |
| 6I***82 | Lever As | 1 |
| 6I***83 | Spring | 2 |
7e-8794 Drive Gp-Gov & Transfer Pump
| 10***68 | Gear As-Drive; (44-Teeth), . Body | 1 |
| 10***85 | Lever-Shutoff; (Output) | 1 |
| 1W***65 | Ring-Retaining | 1 |
7w-4812 Fastener Gp-Fuel Inj Pump
| 1T***68 | Seal-O-Ring; (Fuel Injection Pump) | 1 |
| 6F***73 | Seal--To Top Cover On Selector Valve | 1 |
| 6V***18 | Bolt (M8x1.25x45mm); (M8x1.25x35-mm) | 3 |
115-2544 Governor Gp
| 10***91 | Spring-Oil Side | 1 |
| 11***44 | Governor Group | 1 |
| 11***47 | Cam Assem. | 1 |
133-3062 Governor Gp-Unit Injector
| 10***90 | Spring-Air Side | 1 |
| 10***92 | Spring-Servo | 1 |
| 10***93 | Spring-Return | 1 |
113-6219 Governor Gp-Unit Injector
| 11***19 | Governor Group-Unit Injector; (Unit Injector) | 1 |
| 11***44 | Governor Group | 1 |
| 13***16 | Lines Group-Governor Oil | 1 |
8l-3471 Joint As-Tube
| 8L***71 | Joint As-Tube | 1 |
| 9X***36 | Seal | 2 |
249-0090 Lines Gp-Fuel
| 10***09 | Cap As-Filler; (Fast Fill Fuel) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 11***61 | Hose As | 1 |
161-1247 Lines Gp-Fuel
| 10***53 | Hose As | 1 |
| 11***72 | Filter Group-Fuel; (Fuel) | 1 |
| 11***73 | Filter Element-Fuel | 1 |
149-1350 Lines Gp-Fuel Filter
| 00***64 | End; (Hose) | 2 |
| 09***61 | Strap; (Cable) | 1 |
| 10***29 | Hose; (60-cm) | 0 |
107-7731 Lines Gp-Fuel Ratio Control
| 10***80 | Tube Assem. | 1 |
| 10***31 | Lines Group-Fuel Ratio Control; Air Fuel Ratio Control Lines Group, Angle | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
135-1716 Lines Gp-Governor Oil
| 13***16 | Lines Group-Governor Oil | 1 |
| 13***57 | Tube Assem. | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
137-2525 Pump Gp-Fuel
| 13***25 | Pump Group-Fuel | 1 |
| 13***74 | Piston | 1 |
| 13***75 | Gasket-Cover | 2 |
192-4302 Pump Gp-Fuel
| 13***74 | Piston | 1 |
| 13***75 | Gasket-Cover | 2 |
| 13***76 | Strainer; (Fuel Pump) | 1 |
107-7732 Pump Gp-Fuel Injection
| 10***32 | Pump Group-Fuel Injection | 1 |
| 11***18 | Seal-O-Ring; (26.64mm Id) | 1 |
| 12***74 | Seal-O-Ring; (7.59mm'Id) | 1 |
159-7574 Pump Gp-Fuel Prm & Prim Filter
| 14***83 | Separator Group-Water | 1 |
| 15***74 | Pump Group-Fuel Prm & Prim Filter | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 4 |
149-5380 Pump Gp-Fuel Transfer
| 08***68 | Spacer | 1 |
| 14***80 | Pump Group-Fuel Transfer | 1 |
| 17***71 | Motor Group-Electric; -Fuel Transfer Pump | 1 |
149-2683 Separator Gp-Water
| 11***01 | Bowl As-Water Collection | 1 |
| 11***18 | Ring-Retaining | 1 |
| 11***19 | Nut | 1 |
129-1101 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 12***01 | Valve Group-Check; -Fuel-Fuel Filter | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
Grade References
109-5624 Leveler Gp -30 Ft Over Screed
| 08***09 | Bracket | 6 |
| 08***38 | Channel | 2 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5627 Leveler Gp -40 Ft Grade
| 10***04 | Tube; (1.1-M) | 1 |
| 10***27 | Leveler Group; -40-Ft Grade Reference | 1 |
| 10***34 | Tube As | 1 |
109-5625 Leveler Gp -30 Ft Over Screed
| 08***09 | Bracket | 7 |
| 08***38 | Channel | 2 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5626 Leveler Gp -Outboard
| 08***09 | Bracket | 5 |
| 08***38 | Channel | 1 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5628 Leveler Gp -30 Ft Grade
| 10***04 | Tube; (1.1-M) | 1 |
| 10***28 | Leveler Group; -30-Ft Grade Reference | 1 |
| 10***34 | Tube As | 1 |
109-5623 Leveler Gp -30 Ft Outboard
| 08***09 | Bracket | 12 |
| 08***38 | Channel | 4 |
| 10***04 | Tube; (1.1-M) | 1 |
109-5622 Leveler Gp -40 Ft Outboard
| 08***09 | Bracket | 12 |
| 08***38 | Channel | 4 |
| 10***04 | Tube; (1.1-M) | 1 |
Hydraulic System
077-3951 Cap Gp-Hydraulic Oil Filler
| 07***51 | Cap As-Filler Breather | 1 |
| 07***32 | Filter Element-Breather; (Hydraulic Oil Filter) | 1 |
| 07***26 | Gasket | 2 |
165-6446 Cooler Gp-Hydraulic Oil
| 10***03 | Manifold; (Forward Return,Rear Return) | 1 |
| 10***26 | Plate | 1 |
| 12***55 | Heat Exchanger | 1 |
180-5854 Cover Gp
| 10***56 | Rod; (Prop) | 1 |
| 14***41 | Shim; (6-mm Thk)(6 mm Thk) | 1 |
| 14***57 | Shim; (2-mm Thk)(2 mm Thk) | 1 |
174-3072 Cylinder Gp-Hydraulic -Auger, Rh
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 07***85 | Washer | 1 |
| 11***60 | Shim; (3-mm Thk) | 1 |
203-4276 Cylinder Gp-Hydraulic -Auger Hoist, Lh
| 20***76 | Cylinder Group-Hydraulic; -Auger Hoist, Lh | 1 |
| 24***11 | Ring-Retaining | 1 |
| 25***75 | Kit-Seal; (Auger Hoist) | 1 |
115-5207 Cylinder Gp-Hydraulic
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 07***69 | Fitting, Grease | 1 |
| 08***25 | Ring; (Backup) | 1 |
203-4273 Cylinder Gp-Hydraulic -Screed Hoist
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 20***73 | Cylinder Group-Hydraulic; -Screed Hoist | 1 |
| 23***05 | Kit-Seal; (Screed Hoist Cylinder) | 1 |
146-3166 Cylinder Gp-Hydraulic -Steering
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 14***66 | Cylinder Group-Hydraulic; -Steering | 1 |
| 15***88 | Seal-Crown | 1 |
135-9444 Cylinder Gp-Hydraulic -Tow Point
| 13***44 | Cylinder Group-Hydraulic; -Tow Point | 1 |
| 17***34 | Kit-Seal; (Towpoint Cylinder) | 1 |
| 17***36 | Ring-Wear | 1 |
203-4275 Cylinder Gp-Hydraulic -Auger Hoist, Rh
| 20***75 | Cylinder Group-Hydraulic; -Auger Hoist, Rh | 1 |
| 24***11 | Ring-Retaining | 1 |
| 24***14 | Kit-Seal; (Auger Hoist) | 1 |
135-0220 Cylinder Gp-Hydraulic -Hopper
| 13***20 | Cylinder Group-Hydraulic; -Hopper | 1 |
| 13***21 | Kit-Seal; (Hopper Cylinder) | 1 |
| 5E***32 | Ring | 1 |
174-3073 Cylinder Gp-Hydraulic -Auger, Lh
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 17***73 | Cylinder Group-Hydraulic; -Auger, Lh | 1 |
| 17***07 | Kit-Seal; (Hydraulic Cylinder) | 1 |
7x-5312 Filter Gp-Oil -Hydraulic
| 14***91 | Filter-Oil; (Advanced Efficiency) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 7X***12 | Filter Group-Oil; -Hydraulic | 1 |
102-8972 Filter Gp-Oil
| 10***72 | Filter Group-Oil | 1 |
| 13***42 | Indicator Group-Oil Filter Change; -Hydraulic | 1 |
| 14***91 | Filter-Oil; (Advanced Efficiency) | 1 |
176-9415 Filter Gp-Oil -Hydraulic Tank
| 05***19 | Filter Element As-Oil; (Hydraulic) | 1 |
| 07***25 | Kit-Seal; (Hydraulic Oil Filter) | 1 |
| 17***15 | Filter Group-Oil; -Hydraulic Tank | 1 |
162-7441 Hydraulic Ar
| 10***81 | Lines Group-Grade & Slope | 1 |
| 11***36 | Lines Group-Lubrication | 1 |
| 12***68 | Lines Group-Screed Elevation | 1 |
133-5342 Indicator Gp-Oil Filter Change
| 13***42 | Indicator Group-Oil Filter Change; -Hydraulic | 1 |
| 15***51 | Seal-O-Ring | 2 |
| 16***39 | Screw | 2 |
162-7443 Lines Gp-Conveyor
| 10***38 | Clamp-Half | 16 |
| 10***72 | Filter Group-Oil | 1 |
| 10***03 | Manifold; (Forward Return,Rear Return) | 2 |
228-5024 Lines Gp-Conveyor
| 10***38 | Clamp-Half | 16 |
| 10***15 | Elbow Group | 2 |
| 10***03 | Manifold; (Forward Return,Rear Return) | 2 |
107-0481 Lines Gp-Grade & Slope
| 10***81 | Lines Group-Grade & Slope | 1 |
| 13***04 | Hose As | 2 |
| 13***05 | Hose As | 2 |
178-7646 Lines Gp-Hopper
| 08***56 | Nut | 5 |
| 09***56 | Hose Assem. | 1 |
| 10***90 | Hose As | 1 |
171-4580 Lines Gp-Paver Ventilation
| 10***39 | Key-Square | 1 |
| 11***57 | Hose As | 1 |
| 11***88 | Hose As | 1 |
121-1268 Lines Gp-Screed Elevation
| 10***79 | Pin | 4 |
| 11***55 | Hose As | 1 |
| 11***79 | Plate | 1 |
166-7773 Lines Gp-Steering
| 00***21 | Nut; (13/16-20-Thd) | 1 |
| 07***43 | Steering Column Group | 1 |
| 10***02 | Hose As | 1 |
180-3718 Lines Gp-Truck Hitch
| 08***45 | Clamp | 4 |
| 08***56 | Nut | 4 |
| 08***73 | Clamp | 4 |
174-4489 Lines Gp-Vibratory
| 10***99 | Pump Group-Gear | 1 |
| 11***86 | Hose As | 1 |
| 13***38 | Hose As | 1 |
228-5870 Lines Gp-Vibratory
| 10***15 | Elbow Group | 1 |
| 11***86 | Hose As | 1 |
| 13***38 | Hose As | 1 |
6r-2203 Motor Gp-Gear
| 1G***84 | Kit-Seal | 1 |
| 1G***85 | Bearing As | 2 |
| 1G***86 | Flange | 1 |
197-1728 Motor Gp-Gear -Blower Fan
| 16***39 | Shim; (1.75-mm Thk) | 1 |
| 19***28 | Motor Group-Gear; -Blower Fan | 1 |
| 1F***22 | Bearing (.500" Long) | 4 |
227-3031 Motor Gp-Gear -Hydraulic Generator
| 08***91 | Valve As-Check; (Hydraulic Fan Oil) | 1 |
| 12***47 | Kit-Seal; (Check Valve) | 1 |
| 13***35 | Seal-Shaft | 1 |
119-8499 Motor Gp-Piston
| 11***99 | Motor Group-Piston | 1 |
| 15***09 | Kit-Seal; (Front Wheel Assist Motor) | 1 |
| 15***11 | Collar-Seal | 1 |
223-0581 Motor Gp-Piston -Drag Conveyor
| 12***13 | Gasket-End Cap | 1 |
| 12***17 | Pin | 1 |
| 12***68 | Plate-Valve | 1 |
193-1008 Motor Gp-Piston -Propel, Rh
| 09***44 | Ring-Retaining | 1 |
| 10***19 | Ring-Retaining | 1 |
| 15***09 | Kit-Seal; (Front Wheel Assist Motor) | 1 |
256-4726 Motor Gp-Piston
| 07***53 | Pin; (Spring) | 2 |
| 13***95 | Orifice | 2 |
| 13***57 | Plug | 4 |
175-7933 Motor Gp-Piston
| 11***21 | Plug-Special | 2 |
| 11***22 | Spring | 2 |
| 17***33 | Motor Group-Piston | 1 |
119-8498 Motor Gp-Piston
| 11***98 | Motor Group-Piston | 1 |
| 15***09 | Kit-Seal; (Front Wheel Assist Motor) | 1 |
| 15***11 | Collar-Seal | 1 |
183-9355 Motor Gp-Piston
| 07***53 | Pin; (Spring) | 2 |
| 09***00 | Seal-O-Ring | 1 |
| 13***95 | Orifice | 2 |
193-1007 Motor Gp-Piston -Propel, Lh
| 09***44 | Ring-Retaining | 1 |
| 10***19 | Ring-Retaining | 1 |
| 15***09 | Kit-Seal; (Front Wheel Assist Motor) | 1 |
8i-0843 Motor Gp-Piston
| 1G***74 | Piston | 7 |
| 1G***75 | Guide-Slipper | 1 |
| 1J***74 | Ring-Retaining | 2 |
223-0583 Motor Gp-Piston -Auger Conveyor
| 11***21 | Plug-Special | 2 |
| 11***22 | Spring | 2 |
| 12***13 | Gasket-End Cap | 1 |
240-7328 Pump & Mtg Gp-Screed Vibratory
| 10***15 | Elbow Group | 1 |
| 14***57 | Elbow As. | 1 |
| 14***88 | Elbow Group | 1 |
226-2451 Pump Gp-Gear -Screed
| 22***51 | Pump Group-Gear; -Screed | 1 |
| 24***29 | Kit-Seal; (Screed Gear Pump) | 1 |
| 24***41 | Kit-Solenoid Valve; (Screed Gear Pump) | 1 |
104-4199 Pump Gp-Gear
| 10***99 | Pump Group-Gear | 1 |
| 11***64 | Kit-Valve Seal | 1 |
| 13***93 | Kit-Pump Seal | 1 |
267-9475 Pump Gp-Gear -Screed
| 24***41 | Kit-Solenoid Valve; (Screed Gear Pump) | 1 |
| 26***75 | Pump Group-Gear; -Screed | 1 |
| 26***42 | Kit-Seal | 1 |
163-1410 Pump Gp-Piston
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 07***53 | Pin; (Spring) | 2 |
163-1409 Pump Gp-Piston
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 07***53 | Pin; (Spring) | 2 |
8i-0836 Pump Gp-Piston -Auxiliary
| 00***93 | Seal-O-Ring (Id=52.07mm); (52.07-mm Id) | 2 |
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 8 |
| 05***33 | Seal | 1 |
288-8644 Pump Gp-Piston
| 03***39 | Seal-O-Ring (Id=9.25mm) | 3 |
| 07***53 | Pin; (Spring) | 2 |
| 09***39 | Washer; (8.33x15x2.12-mm Thk) | 1 |
288-8643 Pump Gp-Piston
| 03***39 | Seal-O-Ring (Id=9.25mm) | 3 |
| 07***53 | Pin; (Spring) | 2 |
| 09***39 | Washer; (8.33x15x2.12-mm Thk) | 1 |
160-5113 Pump Gp-Piston
| 00***63 | Seal-O-Ring; (55.24mm Id) | 2 |
| 03***16 | Bolt-Self Locking; (1/4unc X 3/4) | 8 |
| 10***52 | Cover-Pintle | 2 |
143-2872 Pump Gp-Piston -Drag Conveyor, Auger Conveyor
| 07***75 | Shim | 1 |
| 08***98 | Cover-Gerotor | 1 |
| 08***02 | Plug-Orifice | 2 |
9t-2031 Rotating Gp-Pump
| 00***83 | Ring-Snap | 1 |
| 9T***31 | Rotating Group-Pump; -Steering, Pilot | 1 |
| 9T***57 | Pin | 3 |
176-9413 Tank Gp-Hydraulic
| 07***51 | Cap As-Filler Breather | 1 |
| 10***40 | Tank As-Hydraulic | 1 |
| 10***30 | Cover As | 1 |
176-9414 Tank Gp-Hydraulic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***00 | Plate | 1 |
| 14***08 | Plug As. | 3 |
187-6155 Valve & Mtg Gp-Relief
| 03***53 | Seal-O-Ring; (08.92mm Id) | 2 |
| 11***16 | Kit-Seal; (Counterbalance Valve) | 1 |
| 18***55 | Valve & Mtg Group-Relief | 1 |
134-4720 Valve Gp-Bank
| 08***80 | Case As | 4 |
| 08***83 | Body | 2 |
| 08***85 | Spring | 4 |
220-4133 Valve Gp-Control
| 22***33 | Valve Group-Control; -Shift-Brake | 1 |
| 22***65 | Valve Group-Solenoid; -Shift | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
115-7183 Valve Gp-Control -Right Grade, Hopper
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***09 | Kit-Bolt | 2 |
| 11***83 | Valve Group-Control; -Right Grade, Hopper | 1 |
291-2183 Valve Gp-Control
| 03***39 | Seal-O-Ring (Id=9.25mm) | 3 |
| 12***08 | Gasket-Control | 1 |
| 19***20 | Controller As | 1 |
160-2451 Valve Gp-Control -Flow
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***16 | Solenoid As | 1 |
| 13***11 | Valve-Check | 1 |
147-6937 Valve Gp-Control
| 14***37 | Valve Group-Control | 1 |
| 15***86 | Valve Group-Solenoid | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
169-0166 Valve Gp-Counterbalance
| 07***27 | Kit-Seal; (Counterbalance Valve) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 12***16 | Solenoid As | 2 |
190-4168 Valve Gp-Flow Control
| 19***68 | Valve Group-Flow Control | 1 |
| 19***01 | Coil | 1 |
| 20***76 | Kit-Seal; (Flow Control Valve)(Front Wheel Assist) | 1 |
168-8609 Valve Gp-Pressure Reducing
| 16***09 | Valve Group-Pressure Reducing; -Truck Hitch | 1 |
| 17***45 | Kit-Seal; (Pressure Reducing Valve) | 1 |
| 17***46 | Valve | 1 |
257-5145 Valve Gp-Pump Control -Auxiliary Pump
| 25***45 | Valve Group-Pump Control; -Auxiliary Pump | 1 |
| 4J***33 | Seal Fuel Injection Pump | 1 |
| 5L***58 | Seal 14 mm(.551 In.) I. D. | 1 |
196-6988 Valve Gp-Pump Control
| 19***62 | Pin | 1 |
| 19***64 | Body | 1 |
| 19***88 | Valve Group-Pump Control | 1 |
151-7986 Valve Gp-Solenoid
| 15***86 | Valve Group-Solenoid | 1 |
| 16***12 | Coil; (24-Volt) | 1 |
| 16***13 | Kit-Seal; (Shift Solenoid Valve) | 1 |
220-4165 Valve Gp-Solenoid -Shift
| 16***13 | Kit-Seal; (Shift Solenoid Valve) | 0 |
| 17***23 | Valve-Solenoid | 1 |
| 22***65 | Valve Group-Solenoid; -Shift | 1 |
7r-0197 Pump Gp-Metering -Steering
| 07***24 | Kit-Seal | 1 |
| 17***48 | Kit-Check Valve; (Steering Metering Pump) | 1 |
| 3G***89 | Cap | 1 |
Implements
185-5433 Extension Ar-Auger
| 18***33 | Extension Ar-Auger | 1 |
| 1G***47 | Extension Group-Auger; -6 In | 1 |
| 21***53 | Extension Group-Main Frame | 4 |
177-6816 Extension Gp-Screed
| 12***73 | Extension As | 2 |
| 12***78 | Bar | 2 |
| 12***79 | Bar | 2 |
166-7676 Hitch Gp-Truck
| 05***12 | Ring-Retaining; (Internal) | 2 |
| 09***55 | Washer; (39x72x1.5-mm Thk) | 8 |
| 11***88 | Guide; (31.9x43.5x9.65-mm Thk)(Roller) | 2 |
180-6338 Hitch Gp-Truck
| 16***76 | Hitch Group-Truck; -Oscillating | 1 |
| 18***96 | Guard As | 1 |
| 18***38 | Hitch Group-Truck | 1 |
180-9348 Indicator Gp-Depth
| 17***32 | Film-Identification; (Tow Point Indicator) | 2 |
| 17***73 | Plate | 2 |
| 17***33 | Bar | 2 |
180-6340 Installation Ar-Truck Hitch
| 18***18 | Lines Group-Truck Hitch | 1 |
| 18***38 | Hitch Group-Truck | 1 |
| 18***40 | Installation Ar-Truck Hitch | 1 |
102-4646 Roller Ar-Push
| 10***46 | Roller Ar-Push | 1 |
| 11***58 | Screw; 12-Point Screw, Screw, Roller Group-Push | 1 |
| 5C***66 | Bolt (25 mm Long); (5/8-11x1-In) | 1 |
118-8358 Roller Gp-Push
| 09***55 | Washer; (39x72x1.5-mm Thk) | 10 |
| 11***57 | Roller As | 1 |
| 11***58 | Screw; 12-Point Screw, Screw, Roller Group-Push | 1 |
Lubrication System
131-4810 Breather Gp
| 13***10 | Breather Group; -Crankcase | 1 |
| 2W***62 | Breather As-Crankcase; (Engine) | 1 |
| 4P***36 | Base | 1 |
103-0803 Filler Gp-Engine Oil
| 10***03 | Filler Group-Engine Oil | 1 |
| 5L***52 | Cap Assembly, Including:-; (Engine) | 1 |
| 6L***09 | Seal-Rubber | 1 |
4p-8183 Filter Gp-Engine Oil
| 1R***07 | Filter As-Engine Oil; (Advanced Efficiency) | 1 |
| 23***54 | Gasket | 1 |
| 24***64 | Spring; (Yoke) | 2 |
7w-8420 Fumes Disposal Gp
| 4D***88 | Clip-(Slot To Fit Fastener M10 Or 3/8) | 1 |
| 6V***18 | Bolt (M8x1.25x50mm); (M8x1.25x50-mm) | 1 |
| 7C***52 | Hose-Disposal; (Fumes)(Fumes) | 1 |
110-9674 Gauge Gp-Oil Level (Dipstick)
| 11***74 | Gauge Group-Oil Level (Dipstick) | 1 |
| 1S***63 | Plug; (Mounted-Bottom | 3 |
| 4P***56 | Gauge-Oil Level (Dipstick) | 1 |
112-9099 Gauge Gp-Oil Level (Dipstick)
| 11***99 | Gauge Group-Oil Level (Dipstick) | 1 |
| 11***00 | Gauge-Oil Level (Dipstick); (Engine) | 1 |
| 1S***63 | Plug; (Mounted-Bottom | 3 |
7e-6302 Lines Gp-Engine Oil
| 3P***56 | Seal-O-Ring; (21.82mm Id) | 2 |
| 4W***32 | Elbow-Outlet | 1 |
| 6V***40 | Bolt (M8x1.25x25mm); (M8x1.25x25-mm) | 4 |
4p-7703 Lines Gp-Turbocharger Oil
| 11***19 | Tube As | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
| 1S***57 | Gasket; (Turbocharger-Oil Supply) | 1 |
115-4123 Pump Gp-Engine Oil
| 10***05 | Spring | 1 |
| 11***74 | Shaft As | 1 |
| 11***16 | Shaft As-Idler | 1 |
115-4138 Pump Gp-Engine Oil
| 11***23 | Pump Group-Engine Oil | 1 |
| 11***38 | Pump Group-Engine Oil | 1 |
| 6V***15 | Bolt; (M10x1.5x75-mm) | 2 |
200-4497 Pump Gp-Engine Oil
| 18***77 | Pump Group-Engine Oil | 1 |
| 20***97 | Pump Group-Engine Oil | 1 |
| 7W***37 | Shaft-Oil Pump | 1 |
103-9408 Valve Gp-Fluid Sampling
| 10***08 | Valve Group-Fluid Sampling; -Coolant | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
Machine Arrangement
161-1262 Common Ar
| 11***26 | Conveyor Ar-Drag & Auger | 1 |
| 11***29 | Seat Group | 1 |
| 16***92 | Electrical Ar | 1 |
161-5919 Common Ar
| 11***26 | Conveyor Ar-Drag & Auger | 1 |
| 11***29 | Seat Group | 1 |
| 16***92 | Electrical Ar | 1 |
Operator Station
178-8079 Console Ar
| 16***57 | Console Group-Operator | 1 |
| 17***79 | Console Ar | 1 |
165-6657 Console Gp-Operator
| 01***70 | Setscrew | 2 |
| 03***71 | Capscrew, Csk. Hd., 3/8in.-16 N.C. X 1in. | 4 |
| 03***49 | Nut-Self Lock; (No.10.Unc) | 4 |
114-0322 Gauge Gp-Cluster
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***22 | Gauge Group-Cluster | 1 |
| 11***81 | Kit-Gauge Housing | 1 |
104-7454 Horn & Alarm Gp
| 10***54 | Horn & Alarm Group | 1 |
| 3T***15 | Alarm Group; (Backup)(Back-Up) | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 1 |
132-9382 Lever Gp-Propel
| 08***31 | Tube As | 1 |
| 08***21 | Gasket | 1 |
| 08***22 | Plate-Mounting | 1 |
199-8398 Module Gp-Speedometer & Tach
| 19***98 | Module Group-Speedometer & Tach | 1 |
| 3L***87 | Lockwasher 7.24mm(.285in.)O.D.; (3.7x7.24x.48mm Thk) | 5 |
| 4B***24 | Washer; (3.9x9.6x1.2-mm Thk) | 5 |
161-6590 Panel Gp-Instrument
| 07***00 | Switch As-Toggle; (Starter Engine Battery Charger) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
| 10***33 | Kit; (Receptacle) (Includes Receptacle As) | 6 |
213-8146 Panel Gp-Instrument
| 07***00 | Switch As-Toggle; (Starter Engine Battery Charger) | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
104-7470 Platform Gp
| 10***70 | Platform Group | 1 |
| 10***47 | Pin | 2 |
| 11***11 | Armrest As | 2 |
170-5472 Seat Gp
| 10***68 | Grip-Handle | 2 |
| 10***41 | Umbrella Group; -Bg-225c | 1 |
| 11***84 | Seat Group | 1 |
115-8329 Seat Gp
| 11***29 | Seat Group | 1 |
| 17***72 | Seat Group | 1 |
270-2417 Seat Gp -Vinyl
| 27***17 | Seat Group; -Vinyl | 1 |
| 27***19 | Arm; (Lh) | 1 |
| 27***80 | Arm; (Rh) | 1 |
119-1784 Seat Gp
| 11***84 | Seat Group | 1 |
| 19***76 | Kit-Armrest; (Lh) | 1 |
| 19***77 | Kit-Armrest; (Rh) | 1 |
187-6649 Umbrella Gp -Ap-650b
| 18***49 | Umbrella Group; -Ap-650b | 1 |
106-8541 Umbrella Gp -Bg-225c
| 10***41 | Umbrella Group; -Bg-225c | 1 |
Power Train
166-4084 Assist Gp-Front Wheel
| 00***31 | Cup-Bearing | 4 |
| 00***43 | Nut | 2 |
| 06***15 | Nut; (1-1/4-12-Thd) | 3 |
161-9852 Drive Ar-Wheel
| 16***19 | Wheel Ar | 1 |
| 16***52 | Drive Ar-Wheel | 1 |
| 16***56 | Drive Group-Rear | 1 |
193-2340 Kit-Motor Support
| 19***37 | Plate; (Lh) | 1 |
| 19***39 | Plate; (Rh) | 1 |
| 19***40 | Kit-Motor Support | 1 |
234-5129 Lines Gp-Propel
| 03***92 | Seal; (126.59mm Id) | 1 |
| 12***43 | Hose As | 1 |
| 13***70 | Hose As | 1 |
162-7442 Lines Gp-Propel
| 03***92 | Seal; (126.59mm Id) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***43 | Hose As | 1 |
128-4090 Manifold Gp-Front Wheel Drive
| 11***59 | Valve-Flow | 1 |
| 11***61 | Valve-Relief; (Front Wheel Assist) | 1 |
| 12***84 | Valve-Check | 2 |
160-0287 Planetary Gp-Final Drive
| 11***18 | Shaft-Planetary | 6 |
| 12***28 | Gear-Sun | 1 |
| 12***29 | Gear-Sun | 1 |
288-8431 Pump Gp-Dual Propel
| 28***31 | Pump Group-Dual Propel | 1 |
| 28***43 | Pump Group-Piston | 1 |
| 28***44 | Pump Group-Piston | 1 |
160-7094 Pump Gp-Dual Propel
| 16***94 | Pump Group-Dual Propel | 1 |
| 16***09 | Pump Group-Piston | 1 |
| 16***10 | Pump Group-Piston | 1 |
103-5831 Valve Gp-Differential Lock
| 10***31 | Valve Group-Differential Lock | 1 |
| 11***47 | Valve-Differential | 1 |
| 11***48 | Valve-Solenoid | 1 |
203-9717 Valve Gp-Differential Lock
| 20***17 | Valve Group-Differential Lock, Name-Plate (Lubrication : Offset Boom), Decals; (Lubrication, Offset Boom) | 1 |
| 22***82 | Nut; (1/2-20-Thd) | 1 |
| 22***84 | Kit-Shuttle Valve; (Differential Lock) | 1 |
189-6357 Valve Gp-Differential Lock
| 11***47 | Valve-Differential | 1 |
| 11***48 | Valve-Solenoid | 1 |
| 11***49 | Valve-Shuttle | 1 |
162-2185 Wheel & Tire Gp
| 10***34 | Extension-Valve | 1 |
| 10***35 | Valve-Rim | 1 |
| 11***84 | Tire; (16-R25)(16x25 Xgc) | 1 |
161-8271 Wheel & Tire Gp
| 08***24 | Tire; (Tubeless 18x25-16ply) | 1 |
| 16***71 | Wheel & Tire Group | 1 |
| 18***59 | Wheel Group | 1 |
119-8107 Wheel & Tire Gp
| 11***05 | Wheel As | 1 |
| 11***07 | Wheel & Tire Group | 1 |
| 12***11 | Tire-Solid; (8in) | 2 |
161-9719 Wheel Ar
| 16***71 | Wheel & Tire Group | 2 |
| 16***19 | Wheel Ar | 1 |
162-2184 Wheel Ar
| 16***84 | Wheel Ar | 1 |
| 16***85 | Wheel & Tire Group | 2 |
183-1159 Wheel Gp
| 16***74 | Wheel As | 1 |
| 18***59 | Wheel Group | 1 |
| 4K***79 | Seal-O-Ring | 1 |
180-8056 Wheel Gp
| 16***86 | Wheel As | 1 |
| 18***56 | Wheel Group | 1 |
| 2D***43 | Seal-O-Ring | 1 |
Service Equipment And Supplies
7r-4741 Lines Gp-Spray Down
| 08***77 | Adapter | 1 |
| 1G***70 | Extension-Curve | 1 |
| 1G***79 | Hose As | 1 |
161-2872 Plate & Film Gp
| 03***91 | Pop - Rivet (To Secure Safety Lable) | 4 |
| 08***17 | Film-Instruction; (Manuals Inside) | 1 |
| 08***67 | Film-Warning; (No Step)(No Step) | 2 |
161-5920 Plate & Film Gp
| 16***20 | Plate & Film Group | 1 |
| 16***21 | Plate & Film Group | 1 |
161-5921 Plate & Film Gp
| 03***91 | Pop - Rivet (To Secure Safety Lable) | 8 |
| 08***17 | Film-Instruction; (Manuals Inside) | 1 |
| 08***67 | Film-Warning; (No Step)(No Step) | 2 |
239-3240 Plate & Film Gp -English
| 08***27 | Film-Warning; (Machine Mounting) | 2 |
| 08***52 | Decal-Caution, Hopper Support | 2 |
| 11***96 | Plate-Warning; (Operating Instructions) | 1 |
239-3556 Plate & Film Gp -English
| 08***27 | Film-Warning; (Machine Mounting) | 2 |
| 08***52 | Decal-Caution, Hopper Support | 2 |
| 11***96 | Plate-Warning; (Operating Instructions) | 2 |
239-3241 Plate & Film Gp -French
| 15***38 | Plate-Warning; (Operating Instructions) | 1 |
| 15***07 | Film-Notice; (Machine Shipping) | 2 |
| 15***15 | Film-Warning; (Hopper Support) | 2 |
161-2871 Plate & Film Gp
| 16***71 | Plate & Film Group | 1 |
| 16***72 | Plate & Film Group | 1 |
239-3555 Plate & Film Gp -French
| 15***38 | Plate-Warning; (Operating Instructions) | 1 |
| 15***07 | Film-Notice; (Machine Shipping) | 2 |
| 15***15 | Film-Warning; (Hopper Support) | 2 |
184-8075 Reel Gp-Washdown Hose
| 08***89 | Reel Group-Washdown Hose | 1 |
| 14***52 | Plate | 1 |
| 15***17 | Hose As | 1 |
087-0889 Reel Gp-Washdown Hose
| 08***89 | Reel Group-Washdown Hose | 1 |
| 17***28 | Fitting-Swivel | 1 |
| 17***29 | Seal-V-Ring | 1 |
Slope And Grade Control
194-9341 Beam Gp-Transverse
| 18***74 | Plate | 1 |
| 19***41 | Beam Group-Transverse | 1 |
| 7T***99 | Link | 3 |
119-1766 Beam Gp-Transverse
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 10 |
| 08***15 | Cushion-Rubber | 2 |
| 11***66 | Beam Group-Transverse | 1 |
168-6500 Cable Gp-Control -Grade
| 10***63 | Clamp | 1 |
| 11***95 | Plug | 1 |
| 11***63 | Cable; (Coiled) | 1 |
110-2420 Cable Gp-Control
| 10***20 | Cable As-Rh | 1 |
| 10***21 | Cable As-Lh | 1 |
| 10***22 | Cable As | 2 |
209-3125 Control Gp-Grade & Slope
| 10***63 | Clamp | 1 |
| 11***96 | Plug | 1 |
| 11***97 | Plug | 1 |
209-3130 Control Gp-Grade & Slope
| 11***50 | Kit-Transducer | 1 |
| 11***51 | Kit-Filter; (Foam)(Grade Sensor) | 1 |
| 14***76 | Plug-Connector | 1 |
168-5031 Control Gp-Grade & Slope
| 14***22 | Cover | 1 |
| 14***25 | Seal-Bushing | 1 |
| 14***26 | Gasket | 1 |
239-2367 Control Gp-Grade & Slope
| 10***08 | Sensor Group-Grade; (Control) | 3 |
| 10***10 | Bail-Temperature | 3 |
| 11***50 | Kit-Transducer | 1 |
194-6990 Control Gp-Grade & Slope -Premier Control System
| 11***29 | Cap-Dust | 1 |
| 12***36 | Bracket-Mounting | 2 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
190-7525 Control Gp-Grade & Slope -Topcon Control System
| 10***94 | Junction Box | 2 |
| 10***98 | Control Group-Grade & Slope | 2 |
| 10***08 | Sensor Group-Grade; (Control) | 2 |
144-7938 Control Gp-Grade & Slope -Topcon Control System
109-0187 Control Gp-Grade & Slope -Premier Control System
| 10***87 | Control Group-Grade & Slope; -Premier Control System | 1 |
| 11***43 | Mounting Group-Control; -Topcon Control System | 2 |
| 12***48 | Mounting Group-Control; -Premier Control System | 1 |
192-9234 Control Gp-Grade & Slope -Topcon Control System
| 10***63 | Clamp | 2 |
| 10***20 | Cable As-Rh | 1 |
| 10***21 | Cable As-Lh | 1 |
209-3129 Control Gp-Grade & Slope
| 10***63 | Clamp | 1 |
| 11***96 | Plug | 1 |
| 11***97 | Plug | 1 |
123-0885 Control Gp-Grade & Slope -Premier Control System
113-1195 Control Gp-Grade & Slope -Topcon Control System
| 10***31 | Bracket As | 1 |
| 10***37 | Bracket As | 1 |
| 10***76 | Tube-Control | 2 |
122-0348 Mounting Gp-Control -Premier Control System
| 12***48 | Mounting Group-Control; -Premier Control System | 1 |
| 13***84 | Plate As | 2 |
| 13***85 | Mount As | 2 |
135-3860 Mounting Gp-Control -Premier Control System
| 13***60 | Mounting Group-Control; -Premier Control System | 1 |
| 13***50 | Mount As | 2 |
| 18***61 | Bracket | 1 |
112-4043 Mounting Gp-Control -Topcon Control System
| 11***43 | Mounting Group-Control; -Topcon Control System | 1 |
| 13***89 | Support As; (Sensor) | 1 |
| 25***04 | Spacer | 4 |
185-4064 Sensor Ar-Grade -Premier Control System
| 11***93 | Bracket | 1 |
| 12***91 | Sensor Group-Sonic; -Grade | 1 |
| 18***44 | Jack Group-Height Adjuster | 1 |
185-4061 Sensor Ar-Grade -Premier Control System
| 11***93 | Bracket | 1 |
| 12***90 | Sensor Group-Grade; -Averaging Ski | 1 |
| 18***44 | Jack Group-Height Adjuster | 1 |
122-0090 Sensor Gp-Grade -Averaging Ski
| 12***90 | Sensor Group-Grade; -Averaging Ski | 1 |
| 12***94 | Sensor Group-Grade | 1 |
| 12***99 | Arm-Follower | 1 |
122-0094 Sensor Gp-Grade
| 11***29 | Cap-Dust | 1 |
| 12***94 | Sensor Group-Grade | 1 |
| 22***22 | Kit-Hub; (Grade Sensor) | 1 |
209-3131 Sensor Gp-Grade -Sonic
| 10***63 | Clamp | 1 |
| 10***08 | Sensor Group-Grade; (Control) | 1 |
| 10***10 | Bail-Temperature | 1 |
122-0095 Sensor Gp-Grade -Sonic
| 11***29 | Cap-Dust | 1 |
| 12***95 | Sensor Group-Grade; -Sonic | 1 |
| 14***16 | Faceplate | 1 |
209-3132 Sensor Gp-Grade -Averaging Ski
| 10***63 | Clamp | 1 |
| 10***23 | Cable As; (Grade) | 1 |
| 11***95 | Plug | 1 |
122-0091 Sensor Gp-Sonic -Grade
| 12***91 | Sensor Group-Sonic; -Grade | 1 |
| 12***95 | Sensor Group-Grade; -Sonic | 1 |
| 13***83 | Cable As | 1 |
Undercarriage
166-4082 Bogie Gp-Front
| 00***31 | Cup-Bearing | 8 |
| 00***43 | Nut | 4 |
| 06***15 | Nut; (1-1/4-12-Thd) | 3 |
161-9856 Drive Gp-Rear
| 13***10 | Plate-Cover | 2 |
| 14***06 | Shim; (0.05-mm Thk) | 12 |
| 14***07 | Shim; (0.13-mm Thk) | 12 |
239-2366 Mounting Gp-Averaging Ski
| 23***66 | Mounting Group-Averaging Ski | 1 |
| 28***75 | Collar | 4 |
| 28***77 | Tube | 2 |
BG-240C serial number reference
The machine PIN plate is a riveted metal tag on the paver's main frame (tractor unit), typically near the operator's station or engine compartment side rail — check the OMM's PIN-plate diagram if it is not immediately visible. The PIN reads as a 3-letter/character prefix followed by a sequential serial number (e.g. AGL00001); the prefix identifies the specific model/build series while the trailing digits identify the individual unit in build order.
| Prefix | Identifies | Notes |
|---|---|---|
| AGL | Barber-Greene branded BG-240C wheel asphalt paver, single continuous machine serial range AGL00001-up | Shares its parts book with the Cat-branded AP-900B sister model (same paver platform sold under two brand names; AP-900B carries a separate AGJ prefix in the same document, no prefix bleed between the two). Powered by the Cat 3116T turbocharged inline-six, gross power 114 kW (153 hp) at 2200 rpm, per Caterpillar's own Specalog for this model. No plant/region or firm production year-range data found in available listings — confirm exact production years with dealer. |
Frequently asked questions
What engine powers the Cat BG-240C?
A Cat 3116T turbocharged inline-6 diesel, 6.6L displacement, rated about 114 kW (153-154 hp) gross and roughly 104 kW (139 hp) net.
What is the operating weight of the BG-240C?
Tractor only, approximately 14,445-14,830 kg (31,850-32,700 lb). Full operating weight varies by screed configuration and can climb toward 17,900 kg (39,350 lb) with a wide Extend-A-Mat screed extended.
What replaced the Cat BG-240C?
The same platform was sold in parallel under Cat's own AP-900B badge. There is no direct BG-240D successor; Caterpillar's later D-series wheel pavers (BG-230D, BG-260D and kin) and the AP-1000-family wheel pavers absorbed the mid-size paving role the BG-240C filled as the line moved to C7-ACERT power.
What BG-240C owners discuss
How does the 3116T diesel in the BG-240C hold up long-term, and what quirks show up?
Owners report the 3116T is solid at the moderate load and duty cycle a paver puts on it, with major-overhaul intervals well past 10,000 hours when cooling and fuel systems are kept clean. The recurring complaints are an oil cooler that weeps past its two O-rings (easy to twist or pinch on reassembly, so leaks often trace back to the last service rather than a bad cooler), and injector sleeve/cup wear that lets combustion gas or coolant migrate into the cylinder - this gets misread as a blown head gasket or ring blow-by if the cups aren't checked first. Aftercooler fouling from oil-mist blow-by can also build up if the engine idles a lot between pours instead of working under load. Have your dealer verify any coolant loss or cylinder-intrusion symptom before assuming head gasket failure.
What wear items show up first on the wheel undercarriage?
On wheeled pavers like this one the two rear drive tires take the brunt of the load and wear out well ahead of the smaller front bogie wheels, since the bogies are solid rubber and see comparatively light duty. Regular users lubricate the bogie wheel assemblies and check tire condition/inflation weekly rather than waiting for a scheduled service, since asphalt heat and abrasion accelerate wear on anything left unchecked.
Are there known problems with the Extend-A-Mat screed extensions?
Yes - a recurring complaint on this screed design is that the extension adjustment plates hold a perfect setting empty, then pop out of alignment once a working head of mix is loaded against them, to the point the screed won't fully close. Some techs trace it to the extension frame not seating properly in the weld jig, or not cooling fully before removal, leaving a slight twist that eventually cracks the welds after the plates go back in. Symptoms described include a loud bang after roughly 15 m (50 ft) of paving followed by the extensions moving vertically on their own. Have your dealer verify extension frame and weld condition before returning the screed to service - uncontrolled extension movement during paving is a safety issue, not just a mat-quality one.
What electrical or sensor issues come up on the screed heating system?
The heater harness and connectors sit in a hot, abrasive, weather-exposed spot on any paver screed, and corrosion or a loosened terminal there is the most common cause of an element that won't heat evenly. A bad thermostat or a damaged heating coil produces the same symptom, so the usual troubleshooting order is: check the connections first, then test the thermostat, then inspect the coil itself. Temperature sensors also drift out of calibration over a season and should be cleaned and rechecked periodically rather than replaced on a hunch.
What about the hydrostatic propel and material-feed system - anything to watch for?
The propel and feeder circuits carry electronic self-diagnostics, which owners say catches most feed and propel faults before they strand the machine mid-mat. When a genuine propel problem does show up, it traces more often to the charge pump - low oil level, a clogged suction strainer, or a kinked suction line causing cavitation - than to the main pump itself, so that's the first thing to rule out. On the feed side, the forged-steel conveyor chain and Ni-Hard auger flighting are wear items by design; expect to budget for their replacement over the life of the machine rather than treat it as a defect.
What should I check before buying a used BG-240C?
Confirm which screed came with the machine (Extend-A-Mat 10-20B or Pavemaster 10B) matches the paperwork, then walk the extension plates for looseness or play under simulated load - the pop-out-of-alignment complaint above is the single biggest screed red flag. On the tractor, check the rear drive tires against the front bogie wheels for uneven wear, and look for oil staining around the engine's oil cooler as a sign of the common O-ring weep. Pull whatever fault history the propel/feeder self-diagnostics have logged, and ask for injector-cup or head-gasket work in the engine's service records, since cup wear is often fixed and then re-fixed without being logged as a repeat issue. Have your dealer verify screed frame condition and any engine coolant/cylinder findings before finalizing a purchase.
What's the overall consensus on owning this paver day to day?
Consensus among long-time users is that it's a straightforward, serviceable mid-size wheeled paver as long as the routine wear items get attention - asphalt is hard on chains, bearings, augers, bushings, wiring harnesses, and heating elements across the board, and most of what breaks on this class of machine falls into that bucket rather than a driveline or engine defect. Treat wear-part replacement as routine budget, not a warning sign.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific BG-240C part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.