Caterpillarwheel-type loaderwheel loader
Caterpillar 950F II
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 950F Series II is a medium-frame, four-wheel-drive articulated wheel loader from Cat's F-series 950 lineup, built through the 1990s (sources vary on exact dates, roughly early-to-late 1990s production). It runs the Cat 3116 turbocharged and aftercooled inline-six diesel, a 6.6 L engine rated at 134 kW (180 hp) gross and 127 kW (170 hp) net, paired with an automatic power-shift planetary transmission, heavy-duty axles with enclosed wet-disc brakes, and center-point frame articulation steering. Operating weight runs roughly 16,340 to 16,563 kg (36,030-36,521 lb) depending on bucket and configuration, with a general-purpose bucket near 3.1 cubic meters (4.0 cubic yards) as the typical setup. It replaced the original 950F and was itself succeeded by the 950G.
Series II changes over the base 950F centered on the operator station and controls rather than the core driveline: a larger-glass, quieter, lower-profile cab with easier access and electric transmission shift replaced the earlier F-series cab and mechanical shift linkage, while the 3116 engine, planetary power-shift transmission, and axle/differential architecture carried over largely unchanged. That keeps the 950F II close to the base 950F for driveline parts sourcing, while cab, wiring harness, and shift-control components are Series II-specific and not interchangeable with the earlier F. In the used and parts market, this generation's appeal is its pre-electronic-engine simplicity - a mechanically governed 3116 with no exhaust aftertreatment - which keeps it attractive for rebuild-and-run service in quarry, aggregate, and municipal fleets even as Caterpillar's electronically controlled G- and later-series loaders became the standard new-production option.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 950F II specifications
Engine
| Engine model | Cat 3116, four-stroke-cycle, six-cylinder, turbocharged and aftercooled diesel |
| Gross power | 134 kW (180 hp) at 2200 rpm |
| Net (flywheel) power | 127 kW (170 hp) at 2200 rpm |
| Displacement | 6.6 L (403 cu in) |
| Bore x stroke | 105 mm x 127 mm (4.13 in x 5.0 in) |
| Cylinders | 6, inline |
| Emissions compliance | Meets 1996 US EPA, 1997 EEC and 1997 Japan MOC nonroad diesel exhaust standards for this power class (HC 0.43 g/kWh, CO 1.81 g/kWh, NOx 8.16 g/kWh); predates modern Tier numbering |
Weights
| Operating weight, general-purpose bucket | 16,340-16,563 kg (36,030-36,521 lb), varies with cutting-edge type; includes cab with ROPS, standard 23.5-25 tires, full fuel, coolant, lubricants and operator |
| Operating weight, penetration or rock bucket | 16,445-16,514 kg (36,261-36,413 lb) |
| Operating weight, alternate configurations | Equipment listings for this model also report 15,730-16,880 kg (34,679-37,220 lb) reflecting different bucket, tire and counterweight combinations - weight varies by configuration |
| Ground pressure | Not published for this model |
| Shipping weight | Not published separately from operating weight; use operating weight for transport planning |
Dimensions
| Overall length | 7,649-7,936 mm (25 ft 2 in - 26 ft 0 in), varies with bucket type |
| Overall height, bucket at full raise | 5,247-5,372 mm (17 ft 3 in - 17 ft 8 in) |
| Height to top of cab/ROPS (transport) | approx. 3,400-3,520 mm (11 ft 2 in - 11 ft 7 in), figures vary slightly by tire configuration |
| Width over tires | 2,753 mm (9 ft 0 in / 108.4 in) with standard 23.5-25 tires |
| Tread width (gauge) | 2,090 mm (82 in), same across all tire options |
| Wheelbase | 3,180 mm (10 ft 5 in) |
| Ground clearance | 394-474 mm (15.5-18.7 in) depending on tire choice; 474 mm (18.7 in) with standard 23.5-25 tires |
| Minimum turning radius, over tire | 6,419 mm (21 ft 1 in) |
| Loader clearance circle, bucket in carry position | 13,794-13,905 mm (45 ft 3 in - 45 ft 9 in) |
Performance
| Max forward travel speed, 4-speed powershift (23.5-25 tires) | Gear 1: 7.4 km/h (4.6 mph); Gear 2: 13.3 km/h (8.3 mph); Gear 3: 23.1 km/h (14.4 mph); Gear 4: 38.7 km/h (24.0 mph) |
| Max reverse travel speed, 4-speed powershift (23.5-25 tires) | Gear 1: 8.2 km/h (5.1 mph); Gear 2: 14.7 km/h (9.1 mph); Gear 3: 25.5 km/h (15.8 mph); Gear 4: 42.7 km/h (26.5 mph) |
| Breakout force | 14,960-17,715 kg (32,980-38,173 lb) with general-purpose bucket, depending on cutting edge; approx. 16,271 kg (35,870 lb) with penetration bucket; approx. 14,610 kg (32,208 lb) with rock bucket |
| Static tipping load, straight | 11,442-11,880 kg (25,230-26,195 lb) with general-purpose bucket |
| Static tipping load, full 35-degree turn | 10,388-10,813 kg (22,906-23,843 lb) with general-purpose bucket |
| Hydraulic cycle time | Raise 6.6 sec, dump 2.2 sec, lower (empty, float down) 3.0 sec, total 11.8 sec |
| Gradeability | Not published for this model |
Service capacities (summary)
| Fuel tank | 259 L (67 gal) |
| Hydraulic system, including tank | 153 L (40.4 gal); hydraulic tank alone 88 L (23.3 gal) |
| Engine oil (crankcase) | 31 L (8.1 gal) |
| Cooling system | 49 L (12.9 gal) |
| Transmission | 34 L (9.0 gal) |
| Differentials and final drives, front/rear (each) | 36 L (9.5 gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
950F II fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) — 3116 turbocharged diesel | 31 L (8.2 US gal) | Cat Diesel Engine Oil (Cat DEO). Multigrade SAE 10W-30 is the preferred year-round grade across roughly -18°C to 40°C (0°F to 104°F) ambient. Straight SAE 30 or 15W-40 also acceptable in warmer climates; select grade by ambient temperature per Cat's engine oil viscosity chart. |
| Cooling system | 49 L (12.9 US gal) | Cat Extended Life Coolant/Antifreeze (Cat ELC), premixed with water per Cat's cooling system specification. Conventional heavy-duty coolant/antifreeze with SCA is the listed alternate for machines not filled with ELC. |
| Fuel tank | 259 L (68.4 US gal) | No. 2-D diesel fuel (ASTM D975 or equivalent). No. 1-D diesel recommended in cold weather for easier starting and reduced waxing. |
| Transmission (powershift) | 34 L (9.0 US gal) | Cat TDTO (Transmission/Drive Train Oil). SAE 10W for cold starts, SAE 30 for normal/moderate climates, SAE 50 in hot climates — grade selected by ambient temperature per Cat's viscosity chart. |
| Differential and final drive — front axle | 36 L (9.5 US gal) | Cat TDTO, SAE 30W for standard service. Change interval 2000 hours or 1 year. |
| Differential and final drive — rear axle | 36 L (9.5 US gal) | Cat TDTO, SAE 30W for standard service. Change interval 2000 hours or 1 year. |
| Hydraulic system (total, including tank) | 153 L (40.4 US gal) | Cat TDTO — this generation of wheel loader shares Transmission/Drive Train Oil between the powertrain and the implement hydraulic circuit rather than a separate HYDO fluid. SAE 10W is the common hydraulic-circuit grade; grade otherwise follows the same ambient-temperature selection as the transmission. |
| Hydraulic tank | 88 L (23.3 US gal) | Same as hydraulic system — Cat TDTO, grade by ambient temperature. |
| Grease (all pin/bushing lubrication points — articulation joint, bucket and tilt linkage, steering and lift cylinders, oscillation bearings) | Spec only — no sump capacity | Cat Multipurpose Grease (Cat MPGM). NLGI grade selected by ambient temperature per Cat's grease viscosity chart. Standard interval every 100 service hours or 2 weeks unless a shorter interval is called out for a specific point. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 950F II maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 3,000 h |
|
Servicing the 950F II beyond the schedule
Predictive Maintenance & Fluid Analysis
Pull engine oil samples at every 250-hour change to track 3116 turbo/aftercooled wear metals before bearing or ring damage shows up as compression loss. Sample transmission fluid ahead of the 1000-hour change to catch power-shift clutch material breakdown early - the automatic planetary transmission and wet-disc brakes on this platform are sensitive to fluid degradation. Trend hydraulic oil condition toward the 2000-hour service to flag pump or valve wear on the flow-amplified, pressure-compensated steering and implement circuit. Watch coolant condition between extender treatments to protect the 3116's wet-sleeve cylinder liners from cavitation.
Corrective & Common Repairs
Expect wear at the center-point articulation hitch and pin bushings on high-hour loaders - regrease on schedule or expect play in the steering geometry. The 3116's mechanical fuel system and turbocharger are common failure points on machines nearing high hours; watch for injection pump wear and boost loss. Electric-shift transmission control solenoids and wiring degrade with cab heat cycling, causing shift hunting or false neutral. Lift and tilt cylinder rod seals leak after repeated full-stroke cycling in quarry duty - reseal before contamination reaches the hydraulic tank.
Overhaul & Rebuild Points
Plan an inframe overhaul on the 3116 once oil consumption climbs from cylinder liner and ring wear - the turbocharged, aftercooled block accepts standard wet-sleeve liner kits well. Power-shift transmission rebuilds center on clutch pack and planetary gearset wear from repeated forward-reverse shuttling in loading cycles. Front and rear differential and final-drive planetaries see the heaviest wear on machines running heavy aggregate buckets - inspect at the 2000-hour oil change and rebuild before ring gear or carrier damage sets in. Rebuild main hydraulic pumps and lift/tilt cylinders together to restore matched clearances.
Seasonal & Environment Servicing
In cold climates, verify coolant additive concentration before winter and use the ether starting aid correctly on the 3116 to avoid cylinder liner damage on cold starts; let hydraulic oil warm before full-load lift and tilt cycles. In dusty quarry or aggregate environments, clean the radiator core and engine air precleaner daily and watch the air filter service indicator closely - the turbocharged engine is sensitive to restricted intake airflow. In wet or corrosive yard duty, check articulation and axle seals more often and keep battery terminals and electrical connectors clean to prevent electric-shift transmission faults.
950F II common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 112-6523 | Insert-Fuel Filter | Fuel system service | Check fitment → |
| 1R-0751 | Filter-Fuel | Fuel system service | Check fitment → |
| 1R-0753 | Filter-Fuel | Fuel system service | Check fitment → |
| 7E-5189 | Valve As | Fuel system service | Check fitment → |
| 117-4089 | Element-Water Separator | Fuel system service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
950F II fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| 096F03 | Fuel Level Sensor - voltage above normal (open circuit or short to a high source) | Disconnected or corroded fuel sender connector, broken sender wire, or a bad ground at the instrument cluster | Check the fuel sender connector and harness for continuity, verify the cluster ground, reseat or repair connections |
| 110F08 | Engine Coolant Temperature Sensor - abnormal/erratic signal frequency | Intermittent connector at the coolant temperature sensor, chafed harness wire near the engine, or a failing sensor element | Inspect the sensor connector and harness routing, clean and reseat pins, test sensor resistance against spec and replace if out of range |
| 177F04 | Transmission Oil Temperature Sensor - voltage below normal (short to ground) | Chafed or pinched wire shorting to frame/ground, a corroded connector, or a failed sensor | Trace the wiring from the transmission temperature sensor to the power train ECM for shorts to ground, repair harness or replace sensor as needed |
| 248F02 | Cat Data Link - data erratic, intermittent, or incorrect (communication dropout between machine ECMs) | Low or unstable system voltage from a weak battery or failing alternator, or a corroded/loose data link connector between the Power Train, Implement, and Monitor ECMs | Confirm battery and charging voltage first, then inspect data link wiring and ECM connectors for corrosion or looseness |
| 100F03 | Engine Oil Pressure Sensor - voltage above normal (open circuit) | Disconnected sensor connector, broken sender wire, or a failed oil pressure sensor | Inspect the sensor and connector at the engine block, check wiring continuity back to the ECM, replace the sensor if it tests faulty |
| 190F08 | Engine Speed/Timing Sensor - abnormal frequency signal | Sensor air gap out of specification, a damaged sensor, or metal debris on the sensor tip disrupting the signal | Check sensor mounting and air gap, clean or replace the sensor, inspect wiring for chafing or damage |
| 168F02 | Electrical System Voltage - data erratic/intermittent | Failing alternator, loose or corroded battery cables, or a bad ground strap rather than a single sensor fault | Load-test the battery, check alternator charging output, clean and tighten all ground connections |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
950F II attachments & work tools
General purpose buckets
Standard work tool for the 950F II class, roughly 2.5-3.2 m³ (3.3-4.2 yd³) heaped capacity depending on width and application. Widths in the 2.9-3.5 m (105-115 in) range are typical for this size class, sized to balance with the machine's tipping load.
Multi-purpose (4-in-1) bucket
Clamshell-style bucket used for re-handling, light dozing, grading, and clamping loose material on this loader class. Its clamp function needs a third hydraulic function beyond the standard bucket/tilt circuit, so it is paired with the auxiliary valve arrangement rather than the base two-function setup.
Rock and heavy-duty buckets
Reinforced, wear-resistant buckets built for abrasive or blocky material such as shot rock and quarry face, offered at reduced capacity relative to the general purpose bucket to keep breakout force and structural loading in range for this size class.
Light-material / rehandling buckets
Higher-capacity, lower-density buckets for stockpile and rehandling work (woodchips, coal, light aggregate); wider and deeper than a GP bucket at the same rated capacity class.
Pallet forks
Fork carriages and tine sets are offered in multiple tine lengths for this loader class, mounted on the standard hook-style loader linkage. This is a common factory and dealer-fit work tool for material handling and pallet work.
Cutting edges and bolt-on wear edges
Bolt-on cutting edges and end bits are fitted to bucket lips on this class of loader to extend wear life and improve penetration in abrasive digging conditions; replaceable in the field without removing the bucket.
Bucket/tool mounting system
Standard mounting on this generation of Cat wheel loader is a pin-on hook-style loader linkage carrying the bucket or fork frame directly on the lift arms and tilt lever. Hydraulic pin-grabber style quick couplers were also fitted in the field and by dealers on this size class to allow faster tool changes without repinning.
Hydraulic tool circuit (2-valve base, 3-valve/auxiliary option)
Base hydraulic arrangement runs bucket lift and tilt only (two functions). A third valve/auxiliary hydraulic arrangement is required to run tools needing an extra function, such as a clamp-type multi-purpose bucket or a fork with a top clamp; this is a factory or dealer-installed arrangement, not standard.
High lift arrangement
An optional high-lift linkage/loader arrangement was offered for this model, increasing hinge-pin height and dump clearance versus the standard-lift arrangement, useful for loading over truck sideboards or into taller hoppers at some cost to breakout force.
Ride Control
Optional accumulator-based Ride Control system dampens boom bounce when traveling loaded over rough ground. Intended for load-and-carry and roading applications to cut spillage and improve operator ride comfort; it does not change the work tool itself.
Industrial/severe-duty guarding and tire protection
For scrap, demolition, and waste-handling type duty in this loader class, added underbody and cab guarding along with solid or foam-filled cushion tires are used in place of the standard pneumatic tire to resist punctures; this is a duty-package configuration layered onto the base machine rather than a distinct work tool.
Standard tires
Standard fitment for this size class is pneumatic rock/L-type tread tires around 23.5-25; solid cushion tires are available as an aftermarket/severe-duty alternative for puncture-prone sites.
All 950F II assemblies by section
Every catalogued assembly group for the Caterpillar 950F II. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
136-0596 Aftercooler Gp-Water
| 03***83 | Nipple-Front Axle Suction Port | 1 |
| 10***46 | Hose | 1 |
| 13***96 | Aftercooler Group-Water | 1 |
9y-6984 Aftercooler Gp-Water
| 03***83 | Nipple-Front Axle Suction Port | 2 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 2 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
106-1760 Air Cleaner Gp
| 10***60 | Air Cleaner Group | 1 |
| 1N***03 | Clip Assem. | 1 |
| 4P***24 | Seal-O-Ring | 1 |
106-1761 Air Cleaner Gp
| 0A***26 | Fitting | 1 |
| 10***60 | Air Cleaner Group | 1 |
| 10***61 | Air Cleaner Group | 1 |
100-5992 Cartridge Gp-Turbocharger
| 10***92 | Cartridge Group-Turbocharger | 1 |
1n-4877 Cover Gp-Inlet Manifold
| 1N***77 | Cover Group-Inlet Manifold | 1 |
| 4W***22 | Cover-Inlet Manifold | 1 |
| 6V***19 | Bolt; (M8x1.25x40-mm) | 20 |
9y-4968 Lines Gp-Air
| 7C***55 | Hose | 1 |
| 8T***03 | Clamp; (Hose) | 1 |
| 9Y***68 | Lines Group-Air | 1 |
113-1198 Lines Gp-Air
| 10***79 | Hose; (101.6-mm Id) | 1 |
| 10***70 | Elbow-Exhaust | 1 |
| 11***98 | Lines Group-Air | 1 |
6i-0339 Lines Gp-Air
| 10***81 | Hose; (69.8-mm Id) | 1 |
| 5B***90 | Plug-Pipe | 1 |
| 6I***39 | Lines Group-Air | 1 |
1w-6029 Lines Gp-Air
| 1W***29 | Lines Group-Air | 1 |
| 7C***07 | Elbow | 1 |
| 7C***19 | Hose | 2 |
136-0589 Lines Gp-Air
| 13***88 | Hose | 1 |
| 13***89 | Lines Group-Air | 1 |
| 8T***03 | Clamp; (Hose) | 2 |
7w-9248 Manifold Gp-Exhaust
| 10***38 | Manifold-Exhaust | 1 |
| 11***00 | Gasket-Manifold | 3 |
| 14***48 | Bolt; (M10x1.5x65-mm)(M10x1.50x65mm) | 12 |
4w-3480 Manifold Gp-Inlet
| 11***50 | Gasket | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 3 |
| 4W***80 | Manifold Group-Inlet; Inlet Manifold Group | 1 |
6i-3661 Muffler Gp
| 6I***61 | Muffler Group | 1 |
| 6I***62 | Muffler Assem. | 1 |
| 6I***86 | Bracket-Muffler | 1 |
7e-3509 Pipe As-Exhaust Extension
| 7E***97 | Clamp-Bent Bolt | 1 |
| 7E***09 | Pipe As-Exhaust Extension | 1 |
100-2859 Precleaner Gp
| 10***59 | Precleaner Group | 1 |
| 10***60 | Base Assem. | 1 |
| 3S***66 | Bolt | 1 |
125-1126 Turbocharger Gp
| 12***26 | Turbocharger Group | 1 |
| 12***34 | Cartridge Group-Turbocharger | 1 |
| 12***40 | Cover As-Compressor | 1 |
107-7683 Turbocharger Gp
| 10***59 | Turbocharger Group | 1 |
| 10***83 | Turbocharger Group | 1 |
| 3E***17 | Locknut; (M10x1.5-Thd)(Spiralock) | 1 |
126-5926 Turbocharger Gp
| 12***26 | Turbocharger Group | 1 |
| 12***26 | Turbocharger Group | 1 |
| 3E***17 | Locknut; (M10x1.5-Thd)(Spiralock) | 4 |
105-5059 Turbocharger Gp
| 10***19 | Cartridge Group-Turbocharger | 1 |
| 10***59 | Turbocharger Group | 1 |
| 11***65 | Cover-Compressor | 1 |
100-6608 Turbocharger Gp
| 10***65 | Turbocharger Group | 1 |
| 10***08 | Turbocharger Group | 1 |
| 7C***31 | Gasket-Turbocharger | 1 |
100-5865 Turbocharger Gp
| 10***65 | Turbocharger Group | 1 |
| 10***69 | Housing-Turbine | 1 |
| 10***79 | Housing | 1 |
Basic Engine
108-5759 Camshaft Gp
| 10***94 | Plate-Thrust | 1 |
| 10***59 | Camshaft Group; (Single) | 1 |
| 13***76 | Camshaft Assem. | 1 |
2w-9608 Camshaft Gp
| 10***94 | Plate-Thrust | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 2W***08 | Camshaft Group-Single | 1 |
4w-3462 Carrier Gp-Seal
| 23***83 | Gasket | 1 |
| 24***76 | Seal | 1 |
| 2W***46 | Cover | 1 |
4p-0512 Cover Gp-Cylinder Block
| 11***18 | Bolt As; (M8x1.25x16-mm) | 4 |
| 13***40 | Spacer; (9x15x15-mm Thk) | 1 |
| 17***67 | Spacer; (8.8x16x10-mm Thk)(Marked X) | 4 |
7l-0004 Cover Gp-Front Housing
| 10***20 | Cover As-Front | 1 |
| 13***19 | Seal-Integral; (Integral) | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
4w-2172 Cover Gp-Valve Mechanism
| 11***40 | Gasket; (Valve Cover) | 1 |
| 11***60 | Cover | 1 |
| 4W***72 | Cover Group-Valve Mechanism; Valve Mechanism Cover Group | 1 |
9y-1224 Cover Gp-Valve Mechanism
| 9Y***24 | Cover Group-Valve Mechanism; (Sound Suppression) | 1 |
4w-2197 Crankshaft Gp
| 10***30 | Bearing-Main; (Standard) | 3 |
| 10***25 | Crankshaft Assem. | 1 |
| 10***02 | Bearing-Thrust; (Standard) | 1 |
7c-5826 Cylinder Block Gp
| 2M***71 | Plug-Cup; (38.35mm Avg Od) | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 2W***11 | Bearing-Sleeve; (Camshaft) | 1 |
7e-2482 Cylinder Block Gp
| 10***48 | Cylinder Block Group | 1 |
| 1W***07 | Sleeve | 2 |
| 4P***51 | Tube As-Piston Cooling | 6 |
100-4948 Cylinder Block Gp
| 10***48 | Cylinder Block Group | 1 |
| 2M***71 | Plug-Cup; (38.35mm Avg Od) | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
149-5403 Cylinder Block Gp
| 14***02 | Pin, Cylinder Block As | 1 |
| 14***03 | Cylinder Block Group | 1 |
| 21***86 | Bearing-Sleeve; (Camshaft) | 1 |
129-1095 Cylinder Block Gp
| 12***95 | Cylinder Block Group | 1 |
| 2M***71 | Plug-Cup; (38.35mm Avg Od) | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
119-3065 Cylinder Head As
| 11***61 | Sleeve | 6 |
| 11***65 | Cylinder Head As | 1 |
| 12***53 | Insert-Valve Seat; (Inlet) | 6 |
119-3067 Cylinder Head As
| 11***36 | Seal-Valve Stem | 12 |
| 11***65 | Cylinder Head As | 1 |
| 11***67 | Cylinder Head As | 1 |
107-7720 Cylinder Head As
| 10***09 | Cylinder Head As | 1 |
| 10***20 | Cylinder Head As | 1 |
| 11***36 | Seal-Valve Stem | 12 |
107-7609 Cylinder Head As
| 10***09 | Cylinder Head As | 1 |
| 11***61 | Sleeve | 6 |
| 1W***13 | Insert-Valve Seat; (Exhaust) | 6 |
4p-8262 Cylinder Head As
| 1W***13 | Insert-Valve Seat; (Exhaust) | 6 |
| 4P***62 | Cylinder Head As | 1 |
| 4P***78 | Seat-Valve; (Inlet) | 6 |
9y-6166 Cylinder Head As
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 3 |
| 1W***13 | Insert-Valve Seat; (Exhaust) | 6 |
| 2M***71 | Plug-Cup; (38.35mm Avg Od) | 2 |
4p-8263 Cylinder Head Gp
| 11***80 | Valve-Inlet | 6 |
| 11***36 | Seal-Valve Stem | 12 |
| 11***65 | Cylinder Head As | 1 |
9y-8871 Cylinder Head Gp
| 10***32 | Gasket; (1.61mm Thk) | 1 |
| 12***36 | Bolt-Hex Head; (M20x2.5x160mm) | 14 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 3 |
9y-8850 Cylinder Head Gp
| 10***79 | Valve-Exhaust | 6 |
| 1W***13 | Insert-Valve Seat; (Exhaust) | 6 |
| 1W***15 | Lock-Retainer; (Inlet) | 24 |
4p-8264 Cylinder Head Gp
| 10***32 | Gasket; (1.61mm Thk) | 1 |
| 12***36 | Bolt-Hex Head; (M20x2.5x160mm) | 14 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 3 |
7c-2428 Damper & Pulley Gp
| 10***50 | Pulley; (3 Groove) | 1 |
| 20***88 | Damper Assem. | 1 |
| 6V***30 | Bolt; (M10x1.5x60-mm) | 8 |
115-4208 Drain Gp-Engine Oil
| 11***08 | Drain Group-Oil Pan | 1 |
| 11***19 | Plug-Magnetic; (Engine Oil Pan Drain) | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
7c-4532 Drain Gp-Engine Oil -Shutoff Valve
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 6V***38 | Valve-Shutoff; (Engine Oil Pan Drain) | 1 |
| 7C***32 | Drain Group-Oil Pan; Oil Pan Drain Group | 1 |
7c-0044 Drive Gp-Fan
| 4W***03 | Cup-Roller Bearing | 2 |
| 4W***04 | Cone-Roller Bearing | 2 |
| 4W***42 | Spacer; (35.3x45.5x38.331-mm Thk) | 1 |
4w-5428 Drive Gp-Water Pump
| 03***75 | V-Belt; (Pump Drive)(Water) | 1 |
| 10***67 | Plate As-Idler | 1 |
| 11***04 | Pulley As-Idler | 1 |
7e-0519 Flywheel Gp
| 16***30 | Flywheel Assem. | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 8 |
| 6V***97 | Bolt; (M12x1.75x40-mm)(Locking) | 8 |
2w-8475 Gear Gp-Front
| 2W***65 | Shaft-Idler | 1 |
| 2W***66 | Bearing-Sleeve | 1 |
| 2W***75 | Gear Group-Front; Front Gear Group | 1 |
101-4540 Gear Gp-Front
| 10***07 | Shaft-Cam Idler | 1 |
| 10***08 | Plate-Retaining | 1 |
| 10***40 | Gear Group-Front | 1 |
4w-1103 Housing Gp-Flywheel
| 10***51 | Housing-Flywheel | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
| 2P***94 | Plug-Sealing | 1 |
7l-0002 Housing Gp-Front
| 1U***46 | Sealant (For Locations A) | 0 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 6 |
| 6V***18 | Bolt (M8x1.25x50mm); (M8x1.25x50-mm) | 4 |
101-4539 Housing Gp-Front
| 10***39 | Housing Group-Front | 1 |
| 10***11 | Plug | 2 |
| 13***42 | Housing-Front | 1 |
4w-2515 Lifting Gp-Engine
| 4W***82 | Plate-Lifting; (Rear)(Rear) | 1 |
| 4W***83 | Plate-Lifting; (Front) | 1 |
| 4W***15 | Lifting Group | 1 |
7e-2945 Mounting Gp-Engine & Xmsn
| 2A***38 | Bolt-(3/4" X 2-1/4")-Rops Mounting Bracket To Fender | 8 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 8 |
| 7E***45 | Mounting Group-Engine & Tmsn | 1 |
113-1197 Mounting Gp-Engine & Xmsn
| 11***96 | Support | 2 |
| 11***97 | Mounting Group-Engine & Xmsn | 1 |
| 2A***38 | Bolt-(3/4" X 2-1/4")-Rops Mounting Bracket To Fender | 8 |
115-5340 Pan Gp-Oil
| 11***06 | Pan-Oil | 1 |
| 11***40 | Pan Group-Oil | 1 |
| 26***16 | Gasket-Oil Pan; (Engine) | 1 |
105-1557 Pan Gp-Oil
| 10***56 | Pan-Oil | 1 |
| 10***57 | Pan Group-Oil | 1 |
| 6V***18 | Bolt (M8x1.25x50mm); (M8x1.25x50-mm) | 36 |
107-7639 Piston & Rod Gp
| 10***45 | Crown As-Piston | 1 |
| 10***39 | Piston & Rod Group; Connecting Rod And Piston Group | 1 |
| 10***87 | Ring-Piston (Top-Chrome) | 1 |
107-7546 Piston & Rod Gp
| 10***46 | Ring-Piston (Top) | 1 |
| 10***45 | Crown As-Piston | 1 |
| 10***46 | Piston & Rod Group; Connecting Rod And Piston Group | 1 |
9y-1943 Pulley Gp-Fan & Alt Drive
| 4P***51 | Pulley (Alternator) | 1 |
| 7C***04 | V-Belt Set; (Order Only As A Set) | 1 |
| 7E***96 | Pulley-Fan Drive | 1 |
4w-5429 Pulley Gp-Crankshaft
| 2W***81 | Plate-Clamp; (Pulley Clamp) | 1 |
| 4W***29 | Pulley Group-Crankshaft; Crankshaft Pulley Group | 1 |
| 7W***73 | Pulley-Crankshaft; (1-Groove) | 1 |
107-7722 Rocker Arm Gp
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 1 |
| 10***91 | Seat-Wear | 1 |
| 10***76 | Rocker Arm As; (Unit Injector) | 1 |
115-4120 Seal Gp-Crankshaft
| 11***20 | Seal Group-Crankshaft | 1 |
7e-7590 Seal Gp-Crankshaft
| 24***39 | Seal-Crankshaft; (Front)(Front) | 1 |
| 7E***89 | Seal Group-Crankshaft | 1 |
| 7E***90 | Seal Group-Crankshaft; Crankshaft Seal Group | 1 |
115-4210 Seal Gp-Crankshaft
| 11***10 | Seal Group-Crankshaft | 1 |
| 22***10 | Seal Group-Crankshaft; (Clockwise Rotation) | 1 |
| 24***39 | Seal-Crankshaft; (Front)(Front) | 1 |
7c-1770 Seal Gp-Flywheel Housing
| 1U***46 | Sealant (For Locations A) | 0 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
7c-2273 Support Gp-Engine
| 6V***96 | Bolt; (M12x1.75x80-mm) | 5 |
| 6V***78 | Washer; (M13x24x2.5mm) | 6 |
| 6V***36 | Bolt; (M12x1.75x70-mm) | 1 |
4p-4372 Mechanism Gp-Fuel Pump & Valve
| 10***22 | Rocker Arm Group-Valve | 6 |
| 2D***42 | Ball 6.35 mm(.25 In.)Diameter | 2 |
| 3E***12 | Dowel; (Bushing) | 6 |
Braking System
114-1151 Accumulator Gp-Brake -Charged
| 03***13 | Screw-Forming; (10-24x0.37-In) | 2 |
| 06***35 | Valve-Gas | 1 |
| 06***36 | Protector-Gas Valve | 1 |
8r-3585 Accumulator Gp-Brake -Charged
| 03***13 | Screw-Forming; (10-24x0.37-In) | 2 |
| 06***35 | Valve-Gas | 1 |
| 06***36 | Protector-Gas Valve | 1 |
9c-9835 Brake Gp-Parking
| 1B***07 | Nut 1.6 cm(.64 In.) Thick | 2 |
| 4V***14 | Camshaft-Brake | 1 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 4 |
9c-5956 Brake Gp-Parking
| 8R***77 | Spring | 2 |
| 8R***78 | Spring-Shoe | 1 |
| 8R***79 | Plate Assem. | 1 |
147-6930 Brake Gp-Parking
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 8 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 4 |
| 10***91 | End-Yoke Rod | 1 |
9c-9834 Brake Gp-Parking
| 9C***56 | Brake Group-Parking; (Japan Sourced) | 1 |
| 9C***34 | Brake Group-Parking | 1 |
| 9C***35 | Brake Group-Parking; (Us Sourced) | 1 |
106-0434 Brake Gp-Parking
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 8 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 4 |
| 10***91 | End-Yoke Rod | 1 |
121-0902 Control Gp-Foot Brake
| 00***84 | Terminal-Blade; (16-Ga To 20-Ga) | 4 |
| 10***17 | Switch As-Limit; (Stop Light) | 1 |
| 10***18 | Switch As-Limit; (Transmission Neutralizer) | 1 |
149-1907 Control Gp-Foot Brake
| 00***84 | Terminal-Blade; (16-Ga To 20-Ga) | 4 |
| 10***17 | Switch As-Limit; (Stop Light) | 1 |
| 10***18 | Switch As-Limit; (Transmission Neutralizer) | 1 |
106-4842 Control Gp-Foot Brake
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 10***17 | Switch As-Limit; (Stop Light) | 1 |
| 10***18 | Switch As-Limit; (Transmission Neutralizer) | 1 |
105-5148 Control Gp-Parking Brake
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 13***35 | Knob | 1 |
| 5C***61 | Nut (M8x1.25 Thd); (M8x1.25 Thd) | 1 |
104-7636 Control Gp-Service Brake
| 09***45 | Washer; (16.6x24x1.2-mm Thk) | 6 |
| 10***85 | Hose Assem. | 1 |
| 10***41 | Valve Group-Brake Control; -Parking | 1 |
119-6744 Valve Gp-Brake Control
| 11***44 | Valve Group-Brake Control; -Service | 1 |
| 4E***42 | Boot-Valve Piston | 1 |
| 4E***50 | Kit-Seal; (Brake) | 1 |
100-8941 Valve Gp-Brake Control
| 10***41 | Valve Group-Brake Control; -Parking | 1 |
| 10***34 | Repair Kit | 0 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
Cooling System
4p-8184 Cooler Gp-Engine Oil
| 4P***84 | Cooler Group-Engine Oil; Engine Oil Cooler Group | 1 |
| 7C***60 | Gasket | 1 |
| 7W***03 | Core As-Oil Cooler | 1 |
100-6269 Cooler Gp-Engine Oil
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***70 | Core As-Engine Oil Cooler | 1 |
| 17***61 | Gasket | 1 |
9y-1952 Fan Gp-Blower
| 11***16 | Spider Assem. | 1 |
| 7E***98 | Guard Assem. | 2 |
| 7X***18 | Bolt-Plt; (M8 X 1.25 X 45) | 6 |
7e-3584 Lines Gp-Water
| 2W***12 | Gasket-Water Regulator; (Water Regulator) | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
7e-3504 Lines Gp-Water
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 3S***43 | Seal-Lip Type; (Water Temperature Regulator) | 1 |
| 4W***94 | Regulator-Water Temperature; (92 Deg C.) | 1 |
107-7754 Pump Gp-Water
| 10***53 | Pump Group-Water | 1 |
| 10***54 | Pump Group-Water | 1 |
| 2M***53 | Seal--To Seal Brake Housing To Main Housing | 1 |
126-5916 Pump Gp-Water
| 11***25 | Filter; (Water)(Pump) | 1 |
| 12***16 | Pump Group-Water | 1 |
| 12***21 | Housing As-Pump | 1 |
107-7753 Pump Gp-Water
| 10***52 | Pump As-Water | 1 |
| 10***53 | Pump Group-Water | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
4e-9515 Radiator Ar
| 12***50 | Radiator Group | 1 |
| 4E***15 | Radiator Ar | 1 |
| 7E***79 | Radiator Group | 1 |
4p-7657 Radiator Gp
| 4P***51 | Core As-Oil Cooler; (Hydraulic) | 1 |
| 4P***93 | Core As-Radiator | 5 |
| 4P***09 | Baffle Assem. | 3 |
126-2350 Radiator Gp
| 12***50 | Radiator Group | 1 |
| 12***51 | Radiator Group | 1 |
| 6L***17 | Cap-Radiator; (7-Psi)(Coolant Tank) | 1 |
4p-7656 Radiator Gp
| 4D***94 | Clip-- Compressor Clutch Wire To Compressor Body | 1 |
| 4P***56 | Radiator Group | 1 |
| 4P***57 | Radiator Group | 1 |
126-2351 Radiator Gp
| 12***51 | Radiator Group | 1 |
| 4P***51 | Core As-Oil Cooler; (Hydraulic) | 2 |
| 4P***73 | Core As-Radiator | 7 |
7e-0579 Radiator Gp
| 5M***14 | Pipe Plug Cylinder Block Oil Pressure | 1 |
| 6L***17 | Cap-Radiator; (7-Psi)(Coolant Tank) | 1 |
| 7B***97 | Clip 4.29 cm(1.687 In.) Long | 2 |
126-2348 Radiator Gp
| 12***45 | Tank As-Radiator Top | 1 |
| 12***47 | Tank As-Radiator Bottom | 1 |
| 12***48 | Radiator Group | 1 |
126-2349 Radiator Gp
| 12***48 | Radiator Group | 1 |
| 12***49 | Radiator Group | 1 |
| 4D***94 | Clip-- Compressor Clutch Wire To Compressor Body | 1 |
7e-0641 Radiator Gp
| 3L***93 | Tube-Overflow | 1 |
| 4P***51 | Core As-Oil Cooler; (Hydraulic) | 2 |
| 4P***93 | Core As-Radiator | 7 |
Electrical And Starting System
3e-6328 Alarm Gp -Action
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 3E***28 | Alarm Group; -Caterpillar Monitoring System-Action | 1 |
9g-9813 Alarm Gp
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
100-5045 Alternator Gp-Charging
| 10***45 | Alternator Group-Charging; (Nippondenso) | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
100-5046 Alternator Gp-Charging
| 10***46 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 2K***21 | Locknut (5/8-18 Thd) | 1 |
100-5047 Alternator Gp-Charging
| 10***45 | Alternator Group-Charging; (Nippondenso) | 1 |
| 10***46 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 10***47 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
7e-0578 Alternator Gp-Charging
| 10***47 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 4P***65 | Bracket | 1 |
| 4P***87 | Wire Assem. | 1 |
106-0429 Battery & Wiring Gp
| 03***48 | Clip; (11.11mm .437in Id) | 4 |
| 03***97 | Boot | 1 |
| 0A***21 | Clip | 1 |
123-7416 Sensor Gp-Position
| 12***16 | Control Group; (Rotary Position Sensor) | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
112-5148 Control Gp-Autoshift
| 11***33 | Film-Ident-Locate In Cab On The Control | 1 |
| 11***48 | Control Group-Autoshift | 1 |
| 13***88 | Control Group-Tmsn Electronic | 1 |
7t-8000 Converter Gp-Electrical
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 7N***81 | Housing-Receptacle; (14-Ga To 18-Ga) | 1 |
108-3285 Heater Ar-Air Inlet
| 10***63 | Starting Aid Group | 1 |
| 10***85 | Heater Ar-Air Inlet | 1 |
| 11***59 | Engine Ar | 1 |
9x-3294 Heater Gp-Jacket Water
| 12***86 | Element As-Jacket Water Heater; (120-Volt, 1000-Watt) | 1 |
| 13***48 | Kit-Seal; (Jacket Water Heater) | 1 |
| 6N***04 | Cap As-Dust; (Jacket Water Heater Elements) | 1 |
9x-3293 Heater Gp-Jacket Water
| 12***86 | Element As-Jacket Water Heater; (120-Volt, 1000-Watt) | 1 |
| 9X***93 | Heater Group-Jacket Water | 1 |
3t-8724 Heater Gp-Jacket Water
| 2H***24 | Lockwasher | 1 |
| 2R***80 | Nut-Plain Hex | 1 |
| 3T***23 | Element As-Jacket Water Heater; (1000w/230v) | 1 |
9x-1439 Lamp Gp-Flood -Vertical
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***39 | Lamp Group-Flood; -Rear-Ladder Access-Engine Work Light | 1 |
| 9X***55 | Body As-Lamp | 1 |
8c-6207 Lamp Gp-Stop & Tail -Stop, Tail
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***82 | Housing (Plug) (To Lift Kickout Switch) | 1 |
7x-6066 Lamp Gp-Signal
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
3e-6466 Lamp Gp-Signal
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 3E***65 | Wedge; (Receptacle Lock) (2 Pin) | 1 |
| 3E***66 | Lamp Group-Signal; -Rear Turn, Parking | 1 |
108-9427 Lighting Gp-Flood
| 10***27 | Lighting Group-Flood | 1 |
| 11***07 | Stud-Weld | 2 |
| 4E***85 | Bracket Assem. | 2 |
4e-8477 Lighting Gp-Flood & Signal -6-Lamp, Front, Rear
| 13***61 | Sheet | 2 |
| 4E***85 | Bracket Assem. | 2 |
| 4E***87 | Cover Assem.; (Lh) | 2 |
9u-1830 Lighting Gp-Signal -4-Lamp, Front, Rear
| 10***46 | Cover | 1 |
| 10***47 | Bracket As | 1 |
| 11***02 | Harness Assem. | 1 |
111-9301 Lighting Gp-Signal -4-Lamp, Front, Rear
| 10***46 | Cover | 1 |
| 10***47 | Bracket As | 1 |
| 11***01 | Lighting Group-Signal; -4-Lamp, Front, Rear | 1 |
124-4672 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***72 | Pressure Sensor Group; -Lift Cylinder Oil | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
130-0956 Sensor Gp-Arc Suppressor
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***07 | Kit-Connecting Plug; (2-Pin)(Electronic Control) | 1 |
| 13***56 | Sensor Group-Arc Suppressor | 1 |
110-8190 Sensor Gp-Position -Lift
| 11***90 | Sensor Group-Position; (Rotary Position Sensor) | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
103-2040 Sensor Gp-Pressure -Lift Cylinder Oil
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 0 |
| 10***40 | Sensor Group-Pressure; -Lift Cylinder Oil | 1 |
| 3E***70 | Receptacle As-Connector; (3-Pin) | 1 |
131-0784 Sensor Gp-Temperature
| 11***50 | Sleeve (31cm); (31-cm) | 0 |
| 13***84 | Sensor Group-Temperature; -Torque Converter-Tractor Converter Oil | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
7c-4028 Solenoid Gp-Shutoff
| 15***52 | Solenoid As; (Fuel Shutoff) | 1 |
| 4B***74 | Washer (Required Only When Bosch Alternator Is Fitted) | 1 |
| 4K***88 | Seal; Adapter To Oil Pump Outlet Manifold | 1 |
102-8823 Starting Aid Gp
| 10***58 | Cover-Inlet Manifold | 1 |
| 10***62 | Elbow | 1 |
| 10***23 | Starting Aid Group; (Heater) | 1 |
107-5663 Starting Aid Gp
| 03***12 | Terminal-Ring; (2-Ga, 1/4-In Screw)(Circuit Breaker) | 1 |
| 03***48 | Clip; (11.11mm .437in Id) | 4 |
| 10***28 | Wire Assembly; (With Ride Control) (To Option Code Plug Of Main Harness) | 1 |
106-9086 Starting Aid Gp
| 10***86 | Starting Aid Group; (Heater) | 1 |
| 10***52 | Heater As; (22-Volt, 2160-Watt)(Air Inlet) | 1 |
| 10***46 | Hose | 1 |
134-2356 Starting Aid Gp
| 10***52 | Heater As; (22-Volt, 2160-Watt)(Air Inlet) | 1 |
| 10***47 | Strap-Grounding | 1 |
| 12***79 | Stud-Taperlock; (M8x1.25x130-mm) | 1 |
129-1647 Starting Aid Gp
| 03***48 | Clip; (11.11mm .437in Id) | 2 |
| 10***30 | Plate | 1 |
| 10***89 | Cable Assem. | 1 |
109-0839 Starting Aid Gp-Ether
| 10***39 | Starting Aid Group-Ether | 1 |
| 10***73 | Tube | 1 |
| 11***60 | Tube | 1 |
207-1517 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
| 10***49 | Housing As-Starter | 1 |
106-8559 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***63 | Terminal As-Starter | 1 |
111-4275 Starting Motor Gp-Electric
| 10***58 | Starting Motor Group-Electric | 1 |
| 11***75 | Starting Motor Group-Electric; (Cold Weather) | 1 |
| 11***73 | Bolt-12 Point Head; (M10x1.5x35-mm) | 3 |
106-8558 Starting Motor Gp-Electric
| 10***58 | Starting Motor Group-Electric | 1 |
| 10***59 | Starting Motor Group-Electric; Electric Starting Motor Group (Delco Remy) | 1 |
105-8827 Suppressor Gp-Electronic
| 10***27 | Suppressor Group-Electronic; -Air Conditioner Compressor | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
3e-0075 Switch Gp-Magnetic
| 17***22 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
| 3E***75 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
175-2322 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***22 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
175-2324 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***24 | Switch Group-Magnetic; -Air Inlet Heater, Start Relay | 1 |
9g-7641 Switch Gp-Start -Engine, Key
| 6V***24 | Lock As-Cylinder | 1 |
| 6V***62 | Screw-Machine; (8-32x0.31-In) | 4 |
| 7T***99 | Nut-Mounting; (1-32-Thd) | 1 |
3e-0155 Switch Gp-Wiper -Intermittent-Front
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 2H***20 | Lockwasher (11.38mm Id) | 1 |
128-5421 Warning Gp-Backup
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***49 | Alarm Group | 1 |
| 12***21 | Warning Group-Backup | 1 |
8r-9568 Warning Gp-Backup
| 3T***15 | Alarm Group; (Backup)(Back-Up) | 1 |
| 7X***38 | Bolt-Plt; (M8 X 1.25 X 100) | 2 |
| 8R***68 | Warning Group-Backup | 1 |
7i-3905 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
| 10***30 | Gasket | 1 |
106-7778 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 09***68 | Washer; (5x16x1.2-mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
116-6883 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 09***68 | Washer; (5x16x1.2-mm Thk) | 16 |
| 10***29 | Plate Assem. | 1 |
107-3025 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 09***68 | Washer; (5x16x1.2-mm Thk) | 4 |
| 10***29 | Plate Assem. | 1 |
124-1519 Wiring Gp-Cab -Enclosed
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 09***68 | Washer; (5x16x1.2-mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
9u-2772 Wiring Gp-Engine
| 10***07 | Harness As-Transmission | 1 |
| 10***12 | Harness As | 1 |
| 10***67 | Sensor As-Speed; (Magnetic Low Output) | 1 |
9u-2773 Wiring Gp-Front
| 10***02 | Harness As | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
| 3T***50 | Clip | 2 |
102-8738 Wiring Gp-Payload Sensor
| 10***77 | Adapter | 1 |
| 10***38 | Wiring Group-Payload Sensor | 1 |
| 10***72 | Harness Assembly | 1 |
108-9674 Wiring Gp-Platform
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
| 10***30 | Gasket | 1 |
122-3675 Wiring Gp-Platform
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
| 10***30 | Gasket | 1 |
122-3678 Wiring Gp-Platform
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 12 |
| 10***29 | Plate Assem. | 1 |
| 10***30 | Gasket | 1 |
9u-1823 Wiring Gp-Rear
| 12***74 | Harness As-Rear | 1 |
| 12***60 | Cover | 1 |
| 5P***48 | Grommet Wires To Plate; Grommet-Wires To Plate | 2 |
107-0005 Wiring Gp-Relay Panel
| 10***05 | Wiring Group-Relay Panel | 1 |
| 13***89 | Harness As-Power | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 2 |
9u-1828 Wiring Gp-Ride Control
| 10***30 | Wire As; (For Use Without A.I.H) | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 1 |
| 4D***94 | Clip-- Compressor Clutch Wire To Compressor Body | 4 |
4e-0947 Wiring Gp-Secondary Steering
| 13***47 | Switch As-Flow; (Secondary Steering) | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
Engine Arrangement
112-9039 Engine Ar
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***39 | Housing Group-Front | 1 |
| 10***40 | Gear Group-Front | 1 |
116-7958 Engine Ar
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***08 | Turbocharger Group | 1 |
| 10***95 | Control Group-Fuel Injection | 1 |
116-7959 Engine Ar
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***08 | Turbocharger Group | 1 |
| 10***23 | Starting Aid Group; (Heater) | 1 |
106-1756 Engine Ar
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***08 | Turbocharger Group | 1 |
| 10***30 | Filler Group-Engine Oil | 1 |
138-1402 Engine Ar-Non-Runnable
| 10***69 | Cooler Group-Engine Oil | 1 |
| 10***95 | Control Group-Fuel Injection | 1 |
| 10***39 | Piston & Rod Group; Connecting Rod And Piston Group | 6 |
Frame And Body
9u-1819 Counterweight Gp
| 2K***49 | Pin-Spring | 1 |
| 3S***23 | Washer 5.7 cm(2.24 In.)O.D. | 6 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 1 |
6w-5798 Door Gp-Battery
| 5M***62 | Bolt; (3/8-16x0.75-In) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 6V***70 | Rivet-Pop | 10 |
113-4897 Fender Gp
| 10***53 | Bumper-Conical | 2 |
| 10***73 | Cover | 2 |
| 11***38 | Fender As; (Lh) | 1 |
4e-8470 Fender Gp
| 10***53 | Bumper-Conical | 2 |
| 10***73 | Cover | 2 |
| 4E***80 | Fender Assem. (R. H.) | 1 |
105-9796 Firewall Gp
| 10***96 | Firewall Group | 1 |
| 10***98 | Firewall Assem. | 1 |
| 11***90 | Door As | 1 |
4e-9133 Frame As-Rear
| 06***83 | Stud-Weld; (3/8-16 Thd) 38.1mm Oal | 2 |
| 1M***26 | Lug | 1 |
| 3L***49 | Stud-Weld; (3/8x16x.625in Oal) | 12 |
113-5063 Frame As-Rear
| 06***83 | Stud-Weld; (3/8-16 Thd) 38.1mm Oal | 2 |
| 11***63 | Frame As-Rear | 1 |
| 1M***26 | Lug | 1 |
8r-1849 Frame Gp-Loader
| 10***28 | Name-Plate (Lifting Capacity) (Std. Cab), Plate | 2 |
| 3L***49 | Stud-Weld; (3/8x16x.625in Oal) | 12 |
| 3V***62 | Hitch As-Upper | 1 |
8r-4837 Guard Gp-Crankcase
| 5D***26 | Clamp-Band; (9/16 To 1 1/16) | 2 |
| 5P***67 | Hose (.625 In. I.D.)17.02 Dm(67 In.) | 0 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 8 |
4e-0246 Guard Gp-Front
| 12***66 | Plate | 1 |
| 4E***46 | Guard Group-Front | 1 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 6 |
3v-0144 Guard Gp-Power Train
| 0S***92 | Bolt--Cover To Flywheel Housing | 4 |
| 1A***37 | Bolt Clutch Assembly To Bracket (Fan Support) | 4 |
| 3V***44 | Guard Group-Power Train; Power Train Guard Group | 1 |
104-7342 Guard Gp-Radiator
| 10***24 | Plate | 1 |
| 10***49 | Plate | 2 |
| 10***83 | Handle - Grab | 4 |
111-8432 Handrail Gp
| 10***96 | Handle As; (Lh)(Lh) | 1 |
| 11***32 | Handrail Group | 1 |
| 7X***72 | Washer-Hard; (10.2x25.5x2.5-mm Thk) | 8 |
111-8431 Handrail Gp
| 11***31 | Handrail Group | 1 |
| 7X***72 | Washer-Hard; (10.2x25.5x2.5-mm Thk) | 8 |
| 8T***36 | Capscrew; (Hex Hd) (M10 X 1.50 X 25l Gr 10.9) | 8 |
3v-0119 Hitch Gp-Articulating
| 1B***25 | Cup-Roller Bearing | 2 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 2 |
| 3F***50 | Cone-Roller Bearing | 2 |
106-0319 Hood & Guard Gp
| 06***63 | Screw-Drive; (No 14x1/2-In) | 2 |
| 10***47 | Rod Assem. (L. H.) | 1 |
| 10***50 | Bracket | 2 |
104-5035 Hood & Guard Gp
| 06***63 | Screw-Drive; (No 14x1/2-In) | 2 |
| 10***35 | Hood & Guard Group | 1 |
| 10***36 | Door Assem. (R. H.) | 1 |
113-4903 Ladder Gp
| 10***30 | Step Assem. | 3 |
| 10***91 | Step As | 2 |
| 10***82 | Support-Step; (Rubber) | 6 |
4e-8472 Ladder Gp
| 10***30 | Step Assem. | 3 |
| 10***91 | Step As | 2 |
| 10***82 | Support-Step; (Rubber) | 6 |
8r-1004 Lines Gp-Grease
| 4H***78 | Clip (Small) | 7 |
| 4V***58 | Hose Assem. 82.5 cm(32.48 In.) | 2 |
| 5B***35 | Fitting-Grease; (Straight) | 2 |
7v-2877 Link Gp-Steering Frame Lock
| 00***43 | Pin As | 1 |
| 2K***73 | Locknut Inside Guard Assembly | 1 |
| 3B***47 | Pin-Cotter; (Cotter) | 1 |
Fuel System
105-1695 Control Gp-Fuel Injection
| 10***95 | Control Group-Fuel Injection | 1 |
| 16***56 | Control Group-Fuel Injection | 1 |
| 6V***83 | Bolt (16mm Long); (M6x1x16-mm) | 4 |
7w-6989 Control Gp-Fuel Injection
| 10***59 | Control As-Rack | 1 |
| 6V***83 | Bolt (16mm Long); (M6x1x16-mm) | 4 |
| 7W***89 | Control Group-Fuel Injection; Fuel Injection Control Group | 1 |
7e-9912 Control Gp-Governor
| 4P***46 | Lever Assem. | 1 |
| 5C***53 | Bolt (M6x1.00x16mm); (M6x1x16mm Thk) | 1 |
| 6I***83 | Spring | 2 |
7e-8794 Drive Gp-Gov & Transfer Pump
| 10***85 | Lever-Shutoff; (Output) | 1 |
| 1W***65 | Ring-Retaining | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 2 |
7w-4812 Fastener Gp-Fuel Inj Pump
| 1T***68 | Seal-O-Ring; (Fuel Injection Pump) | 1 |
| 6F***73 | Seal--To Top Cover On Selector Valve | 1 |
| 6V***18 | Bolt (M8x1.25x45mm); (M8x1.25x35-mm) | 3 |
139-5837 Filter & Lines Gp-Fuel
| 00***64 | End; (Hose) | 2 |
| 06***26 | Cap-Tube | 1 |
| 11***23 | Insert-Fuel Filter | 1 |
129-3587 Filter Gp-Fuel
| 11***23 | Insert-Fuel Filter | 1 |
| 12***87 | Filter Group-Fuel; -Primary | 1 |
| 1R***53 | Filter-Fuel | 1 |
108-5769 Filter Gp-Fuel
| 10***69 | Filter Group-Fuel | 1 |
| 1R***51 | Filter-Fuel; (Advanced Efficiency)(High Efficiency) | 1 |
| 2B***41 | Spacer Guard Assembly To Bracket Assembly | 1 |
100-8271 Governor Gp-Unit Injector
| 10***90 | Spring-Air Side | 1 |
| 10***92 | Spring-Servo | 1 |
| 10***93 | Spring-Return | 1 |
135-7313 Governor Gp-Unit Injector
| 10***91 | Spring-Oil Side | 1 |
| 11***43 | Cam Assem. | 1 |
| 13***62 | Governor Group-Unit Injector | 1 |
108-6528 Governor Gp-Unit Injector
| 10***28 | Governor Group-Unit Injector | 1 |
| 11***56 | Spring | 1 |
| 11***73 | Cam Assem. | 1 |
4p-5729 Governor Gp-Unit Injector
| 10***99 | Governor Group-Unit Injector | 1 |
| 10***76 | Cam-Torque | 1 |
| 4P***67 | Spring Group-Governor | 1 |
130-7326 Governor Gp-Unit Injector
| 10***90 | Spring-Air Side | 1 |
| 10***92 | Spring-Servo | 1 |
| 10***93 | Spring-Return | 1 |
107-7829 Governor Gp-Unit Injector
| 10***91 | Spring-Oil Side | 1 |
| 10***29 | Governor Group-Unit Injector | 1 |
| 11***43 | Cam Assem. | 1 |
107-7828 Governor Gp-Unit Injector
| 10***28 | Governor Group-Unit Injector | 1 |
| 10***29 | Governor Group-Unit Injector | 1 |
| 13***13 | Governor Group-Unit Injector | 1 |
4p-5526 Governor Gp-Unit Injector
| 10***28 | Governor Group-Unit Injector | 1 |
| 4P***26 | Governor Group-Unit Injector | 1 |
| 4P***29 | Governor Group-Unit Injector | 1 |
133-3062 Governor Gp-Unit Injector
| 10***90 | Spring-Air Side | 1 |
| 10***92 | Spring-Servo | 1 |
| 10***93 | Spring-Return | 1 |
100-4499 Governor Gp-Unit Injector
| 10***99 | Governor Group-Unit Injector | 1 |
| 10***10 | Lever As-Limit | 1 |
| 10***87 | Sleeve-Limiting | 1 |
144-2506 Kit-Fuel Filter
| 00***64 | End; (Hose) | 2 |
| 11***23 | Insert-Fuel Filter | 1 |
| 11***45 | Hose As | 1 |
8r-5337 Lines Gp-Fuel
| 11***79 | Tube Assem. | 1 |
| 11***81 | Tube Assem. | 1 |
| 1F***48 | Nut 12.70 mm(.50 In.) Thread | 1 |
6i-2420 Lines Gp-Fuel Filter
| 06***26 | Cap-Tube | 1 |
| 11***84 | Tee-O-Ring Port | 1 |
| 11***33 | Tube As | 1 |
107-7731 Lines Gp-Fuel Ratio Control
| 10***80 | Tube Assem. | 1 |
| 10***31 | Lines Group-Fuel Ratio Control; Air Fuel Ratio Control Lines Group, Angle | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
4p-9693 Lines Gp-Fuel Ratio Control
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 4J***77 | Seal - O - Ring (11.23mm Od) | 1 |
7w-8434 Lines Gp-Governor Oil
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 2 |
| 4J***77 | Seal - O - Ring (11.23mm Od) | 2 |
| 6V***28 | Elbow-Face Seal (For 6.35mm Od Tube) | 1 |
107-7732 Pump Gp-Fuel Injection
| 10***32 | Pump Group-Fuel Injection | 1 |
| 11***18 | Seal-O-Ring; (26.64mm Id) | 1 |
| 12***74 | Seal-O-Ring; (7.59mm'Id) | 1 |
7e-7607 Pump Gp-Unit Injection
| 10***30 | Injector Group-Fuel | 1 |
| 11***18 | Seal-O-Ring; (26.64mm Id) | 1 |
| 12***74 | Seal-O-Ring; (7.59mm'Id) | 1 |
8n-5251 Pump Gp-Fuel Prm & Prim Filter
| 1L***69 | Ring-Retaining | 1 |
| 2H***29 | Ring - Retaining External | 1 |
| 2J***57 | Packing,Preformed Screw Assembly Part Of Kit P/N 5r***25 | 1 |
8n-3365 Pump Gp-Fuel Priming
| 10***08 | Pump As; (Fuel Priming) | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
129-3586 Pump Gp-Fuel Priming
| 12***49 | Pump Group-Fuel Prm & Water Sep | 1 |
| 12***86 | Pump Group-Fuel Priming | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
105-8643 Pump Gp-Fuel Prm & Prim Filter
| 10***42 | Tube Assem. | 1 |
| 10***43 | Pump Group-Fuel Prm & Prim Filter | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
127-6449 Pump Gp-Fuel Prm & Water Sep
| 11***01 | Bowl As-Water Collection | 1 |
| 11***89 | Element-Water Separator; (Water/Fuel Seperator) | 1 |
| 11***61 | Base Assem. | 1 |
129-6763 Pump Gp-Fuel Prm & Water Sep
| 11***89 | Element-Water Separator; (Water/Fuel Seperator) | 1 |
| 11***61 | Base Assem. | 1 |
| 11***18 | Ring-Retaining | 1 |
120-8695 Separator Gp-Water
| 12***95 | Separator Group-Water | 1 |
| 12***63 | Pump Group-Fuel Prm & Water Sep | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
113-4904 Tank Gp-Fuel
| 10***49 | Sender As-Fuel Level | 1 |
| 11***43 | Tank As-Fuel | 1 |
| 11***04 | Tank Group-Fuel | 1 |
9u-3761 Tank Gp-Fuel
| 1H***06 | Screw-Purge (1/2-20x1.625in); (1/2-20x1.625-In) | 1 |
| 6C***60 | Gasket (62mm Id); (62 mm Id) | 1 |
| 7I***04 | Tank As-Fuel | 1 |
141-8288 Valve Gp-Fuel Relief
| 14***87 | Spring | 1 |
| 14***88 | Valve Group-Fuel Relief | 1 |
| 2W***94 | Plunger As-Valve | 1 |
Hydraulic System
110-8972 Accumulator & Mtg Gp-Ride Cont
| 06***35 | Valve-Gas | 1 |
| 10***06 | Film-Warning; (High Pressure Cylinder) | 1 |
| 10***33 | Accumulator As-Ride Control | 1 |
108-5933 Accumulator As-Ride Control
| 10***33 | Accumulator As-Ride Control | 1 |
| 15***36 | Valve-Gas; (Brake) | 1 |
| 9T***47 | Seal-Kit | 1 |
159-8219 Accumulator Gp-Ride Control -Uncharged
| 15***19 | Accumulator Group-Ride Control; -Uncharged | 1 |
4t-2626 Cartridge Gp-Vane Pump -Center
| 06***10 | Pin Fastener, Rotor-Pump, . Pin | 1 |
| 06***11 | . Pin, Kit-Vane; (Vane Pump)(Implement, Steering) | 1 |
| 3G***92 | Retainer (Seal) | 4 |
6e-2396 Cartridge Gp-Vane Pump
| 06***57 | Seal-O-Ring | 1 |
| 3G***64 | Retainer (Seal) | 4 |
| 3G***20 | Ring-Seal | 1 |
9u-1827 Control Ar-Ride
| 11***72 | Accumulator & Mtg Group-Ride Cont | 1 |
| 11***41 | Lines Group-Ride Control | 1 |
| 8R***03 | Lines Group-Accumulator; Accumulator Lines Group (Ride Control) | 1 |
7v-5517 Cylinder & Seal Gp-Lift -Rh
| 1U***48 | Cylinder Group-Lift-Rh; -Rh | 1 |
| 7K***09 | Seal-Lip; (76.20mm Id) | 2 |
| 7V***17 | Cylinder & Seal Group-Lift | 1 |
7v-5516 Cylinder & Seal Gp-Lift -Lh
| 1U***47 | Cylinder Group-Lift-Lh; -Lh | 1 |
| 7K***09 | Seal-Lip; (76.20mm Id) | 2 |
| 7V***16 | Cylinder & Seal Group-Lift | 1 |
3v-0136 Cylinder & Seal Gp-Tilt
| 3G***86 | Cylinder Group-Tilt | 1 |
| 3V***36 | Cylinder & Seal Group-Tilt | 1 |
| 7K***10 | Seal-Lip; (82.55 Id) | 4 |
1u-1147 Cylinder Gp-Lift
| 12***06 | Head | 1 |
| 1D***26 | Bolt 6.99 cm(2.75 In.) Long | 4 |
| 1J***08 | Spacer,Ring Uoc:Bsv,Bsx | 1 |
1u-1148 Cylinder Gp-Lift
| 12***06 | Head | 1 |
| 1D***26 | Bolt 6.99 cm(2.75 In.) Long | 4 |
| 1J***08 | Spacer,Ring Uoc:Bsv,Bsx | 1 |
3g-8786 Cylinder Gp-Tilt
| 1A***76 | Bolt 11.43cm (4.50 In.) Long | 2 |
| 1D***28 | Bolt 8.26 cm(3.25 In.) Long | 6 |
| 2H***55 | Bolt 15.88mm(.625in.); 1.59cm(.62in.)Lg. | 4 |
9u-4773 Hydraulic Ar
| 11***20 | Lines Group-Front | 1 |
| 11***21 | Arm As-Lift | 1 |
| 3V***33 | Bearing-Sleeve; (89.2mm Id) | 2 |
9u-1832 Hydraulic Ar
| 11***20 | Lines Group-Front | 1 |
| 11***21 | Arm As-Lift | 1 |
| 3V***33 | Bearing-Sleeve; (89.2mm Id) | 2 |
9c-9750 Kickout & Positioner Gp
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 1F***48 | Nut 12.70 mm(.50 In.) Thread | 2 |
| 3E***93 | Control Group-Bucket Positioner; (Bucket Positioner) | 1 |
8r-5803 Lines Gp-Ride Control
| 10***94 | Strap Assem. | 1 |
| 10***48 | Tube Assem. | 1 |
| 10***33 | Accumulator As-Ride Control | 1 |
8r-3547 Lines Gp-Front
| 1P***04 | Seal - Rectangular (45mm Dia) | 2 |
| 1P***05 | Seal (Check Valve Outlet) | 1 |
| 1P***78 | Flange; (To 5v***09 Tube Assembly) | 12 |
112-7920 Lines Gp-Front
| 11***20 | Lines Group-Front | 1 |
| 11***39 | Tube Assem. | 1 |
| 11***40 | Tube Assem. | 1 |
7v-8359 Lines Gp-Hydraulic
| 1P***05 | Seal (Check Valve Outlet) | 2 |
| 1P***78 | Flange; (To 5v***09 Tube Assembly) | 8 |
| 1P***79 | Flange (Half) | 4 |
8r-5341 Lines Gp-Hydraulic Oil Cooler
| 1L***31 | Clamp-Tube | 6 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 2 |
| 4E***32 | Elbow | 4 |
4e-9516 Lines Gp-Hydraulic Oil Cooler
| 1L***31 | Clamp-Tube | 6 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 2 |
| 3S***65 | Clip (Used Without Cab) | 4 |
9c-8382 Lines Gp-Lift Cylinder
| 10***92 | Tube Assem. (R. H.) | 1 |
| 10***93 | Tube Assem. (L. H.) | 1 |
| 1P***03 | Seal - Rectangular (31.86mm Id) | 6 |
9u-3360 Lines Gp-Pilot
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 4 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
| 4V***39 | Bolt 43.5mm(1.7 In.)Lg. | 2 |
106-0431 Lines Gp-Pilot
| 10***56 | Bracket | 1 |
| 10***26 | Hose Assem. | 1 |
| 10***27 | Hose As | 2 |
113-5941 Lines Gp-Ride Control
| 10***06 | Film-Warning; (High Pressure Cylinder) | 1 |
| 11***72 | Valve Group-Diverter; -Ride Control | 1 |
| 11***40 | Tube Assem. | 1 |
8r-3546 Lines Gp-Tilt Cylinder
| 11***41 | Tube Assem. | 1 |
| 11***42 | Tube Assem. | 1 |
| 1P***04 | Seal - Rectangular (45mm Dia) | 2 |
3v-0132 Mounting Gp-Hydraulic Tank
| 3V***32 | Mounting Group-Hydraulic Tank | 1 |
| 4V***52 | Bracket Assem. | 1 |
| 4V***73 | Bracket Assem. | 1 |
106-0432 Pump & Mtg Gp-Hydraulic
| 10***28 | Pump Group-Vane; -Implement, Steering, Pilot | 1 |
| 10***32 | Pump & Mtg Group-Hydraulic | 1 |
| 5F***06 | Packing,Preformed Pump Mtg Part Of Kit P/N 5r***25 | 1 |
104-3128 Pump Gp-Vane
| 00***62 | Seal-O-Ring; (63.17mm Id) | 3 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 4 |
| 10***28 | Pump Group-Vane; -Implement, Steering, Pilot | 1 |
121-2501 Pump Gp-Vane
| 00***62 | Seal-O-Ring; (63.17mm Id) | 3 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 4 |
| 12***01 | Pump Group-Vane; -Implement, Steering, Pilot | 1 |
6e-6109 Tank & Filter Gp-Hydraulic
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 8 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 66 |
| 11***37 | Tank As | 1 |
5v-7158 Valve & Mtg Gp-Main Control -3-Function
| 4T***49 | Valve Group-Control | 1 |
| 5V***58 | Valve & Mounting Group; -3-Function | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 3 |
4e-8598 Valve & Mtg Gp-Main Control -3-Function
| 4E***98 | Valve & Mtg Group-Control; -3-Function | 1 |
| 6E***37 | Valve Group-Control | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 3 |
4e-3169 Valve & Mtg Gp-Main Control -2-Function
| 4E***69 | Valve & Mtg Group-Control; -2-Function | 1 |
| 6E***78 | Valve Group-Control | 1 |
| 6V***88 | Nut-Full (1/2-13 Thd); (1/2-13-Thd)(Full) | 3 |
4t-2745 Valve Gp-Control -Auxiliary
| 10***83 | Spring; (Outer) | 1 |
| 1U***70 | Shim .178mm(.007in)Thk; 4.53mm(.178in.)Thk. | 2 |
| 1U***71 | Shim .25mm(.010in)Thk; 12.9mm(.508in.)Thk. | 5 |
4t-2746 Valve Gp-Control -Lift, Tilt
| 10***83 | Spring; (Outer) | 2 |
| 1U***70 | Shim .178mm(.007in)Thk; 4.53mm(.178in.)Thk. | 4 |
| 1U***71 | Shim .25mm(.010in)Thk; 12.9mm(.508in.)Thk. | 10 |
6e-0735 Valve Gp-Pilot Cartridge
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 10***37 | Kit-Seal; (Includes Parts Marked J) | 1 |
6e-3528 Valve Gp-Breaker Relief
| 1U***67 | Kit-Seal; (Breaker Relief Valve)(Hydraulic Tank) | 1 |
| 2S***63 | Seal 49.21 mm(1.9375 In.)I.D. | 2 |
| 5P***32 | Ring-Retaining; (23.47mm Id) | 1 |
4t-2749 Valve Gp-Main Control -3-Function
| 00***63 | Seal-O-Ring; (55.24mm Id) | 3 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 6 |
| 1H***96 | Packing,Preformed Cartridge Part Of Kit P/N 4j***80 | 3 |
6e-2378 Valve Gp-Main Control -2-Function
| 00***63 | Seal-O-Ring; (55.24mm Id) | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 2 |
6e-3737 Valve Gp-Main Control -3-Function
| 00***63 | Seal-O-Ring; (55.24mm Id) | 3 |
| 13***89 | Valve Group-Relief | 1 |
| 1H***96 | Packing,Preformed Cartridge Part Of Kit P/N 4j***80 | 3 |
110-4372 Valve Gp-Diverter -Ride Control
| 11***72 | Valve Group-Diverter; -Ride Control | 1 |
| 11***73 | Valve Group; (Ride Control) | 1 |
| 1S***42 | Spring | 1 |
6e-1453 Valve Gp-Diverter -Ride Control
| 1S***42 | Spring | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
6e-5019 Valve Gp-Pilot -2-Function
| 10***02 | Valve Group-Pilot | 1 |
| 10***03 | Valve Group-Pilot; -Tilt | 1 |
| 10***96 | Plate As-Mounting | 1 |
100-5202 Valve Gp-Pilot
| 03***36 | Seal-O-Ring | 1 |
| 10***02 | Valve Group-Pilot | 1 |
| 10***72 | Boot | 1 |
100-5203 Valve Gp-Pilot
| 10***03 | Valve Group-Pilot; -Tilt | 1 |
| 10***72 | Boot | 1 |
| 10***73 | Clamp-Boot | 1 |
6e-5020 Valve Gp-Pilot -3-Function
| 10***02 | Valve Group-Pilot | 1 |
| 10***03 | Valve Group-Pilot; -Tilt | 1 |
| 10***04 | Valve Group-Pilot; -Auxiliary | 1 |
100-5204 Valve Gp-Pilot
| 10***04 | Valve Group-Pilot; -Auxiliary | 1 |
| 10***72 | Boot | 1 |
| 10***73 | Clamp-Boot | 1 |
107-3828 Valve Gp-Pilot Cartridge
| 03***28 | Seal-O-Ring | 1 |
| 10***27 | Seat-Spring | 1 |
| 10***28 | Valve Group-Pilot Cartridge; -Cartridge | 1 |
107-3838 Valve Gp-Pilot Cartridge
| 10***37 | Plunger | 1 |
| 10***38 | Valve Group-Pilot Cartridge | 1 |
| 10***46 | Seat-Spring | 1 |
109-4854 Valve Gp-Pilot Cartridge
| 10***46 | Seat-Spring | 1 |
| 10***54 | Valve Group-Pilot Cartridge | 1 |
| 10***58 | Plunger | 1 |
4t-2742 Valve Gp-Relief -Line
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***42 | Valve Group-Relief; -Secondary Steering | 1 |
6e-6185 Valve Gp-Relief -Main
| 11***15 | Dowel | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 4J***22 | Seal-Interface Between 3rd & Tilt Valve | 1 |
6e-6256 Valve Gp-Relief -Main
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 4J***22 | Seal-Interface Between 3rd & Tilt Valve | 1 |
| 4Y***12 | Plate | 1 |
6e-2377 Valve Gp-Relief -Line
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***71 | Plate | 1 |
4t-4162 Valve Gp-Relief -Line
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***62 | Valve Group-Relief; (Line, Auxiliary Cyl Rod End) | 1 |
4t-2764 Valve Gp-Relief -Line
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***64 | Valve Group-Relief; (Line, Tilt Cylinder Head End) | 1 |
135-5489 Valve Gp-Relief
| 11***15 | Dowel | 1 |
| 13***89 | Valve Group-Relief | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
1u-2226 Valve Gp-Selector & Press Cont
| 1U***26 | Valve Group-Selector & Press Cont; -Pilot Lines | 1 |
| 1U***28 | Valve Group | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 2 |
6e-3078 Valve Gp-Selector & Press Cont
| 10***66 | Adapter | 2 |
| 2M***80 | Seal--To Connector Pump Outlet | 2 |
| 5S***01 | Spacer; (7.54x14.15x0.9-mm Thk) | 2 |
9t-7272 Valve Gp-Shuttle
| 4J***33 | Seal Fuel Injection Pump | 1 |
| 4T***60 | Valve Group-Shuttle; -Ripper Lift-Ripper Tilt-Blade Tilt-Blade Lift | 1 |
| 9S***01 | Plug-O-Ring; (5/16-24 Thd) | 1 |
4t-1860 Valve Gp-Shuttle
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
| 14***05 | Ring-Backup | 2 |
6t-5859 Valve Gp-Solenoid
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
| 2D***35 | Locknut (Visor To Bracket) | 1 |
| 4B***76 | Washer Generator Line Leads (Use As Required) | 1 |
8t-8692 Valve Gp-Solenoid
| 10***70 | Locknut; (1/4-20-Thd) | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
| 4B***76 | Washer Generator Line Leads (Use As Required) | 1 |
Implements
3v-0128 Control Gp-Bucket
| 2D***67 | Fitting-Grease; (Fan Drive) | 2 |
| 2H***43 | Bolt-Plate To Flywheel Housing | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 8 |
108-4925 Logging Ar
| 10***27 | Film (Stripe Cat) | 1 |
| 10***28 | Film (Stripe Cat) | 1 |
| 10***20 | Film (Stripe 950f Serise Ii Logger) | 1 |
Lubrication System
1n-3477 Breather Gp
| 1N***77 | Breather Group; Breather Group | 1 |
| 2W***62 | Breather As-Crankcase; (Engine) | 1 |
| 5N***85 | Washer-Sealing; (Sealing) | 1 |
104-3830 Filler Gp-Engine Oil
| 10***30 | Filler Group-Engine Oil | 1 |
| 10***53 | Tube As | 1 |
| 5L***52 | Cap Assembly, Including:-; (Engine) | 1 |
6i-4515 Filler Gp-Engine Oil
| 5L***52 | Cap Assembly, Including:-; (Engine) | 1 |
| 6I***99 | Tube As | 1 |
| 6I***15 | Filler Group-Oil | 1 |
4p-8183 Filter Gp-Engine Oil
| 1R***07 | Filter As-Engine Oil; (Advanced Efficiency) | 1 |
| 23***54 | Gasket | 1 |
| 24***64 | Spring; (Yoke) | 2 |
7w-8420 Fumes Disposal Gp
| 4D***88 | Clip-(Slot To Fit Fastener M10 Or 3/8) | 1 |
| 6V***18 | Bolt (M8x1.25x50mm); (M8x1.25x50-mm) | 1 |
| 7C***52 | Hose-Disposal; (Fumes)(Fumes) | 1 |
113-1199 Gauge Gp-Oil Level (Dipstick)
| 11***99 | Gauge Group-Oil Level (Dipstick) | 1 |
| 11***00 | Gauge-Oil Level (Dipstick) | 1 |
| 11***68 | Tube As-Guide | 1 |
105-8918 Gauge Gp-Oil Level (Dipstick)
| 10***18 | Gauge Group-Oil Level (Dipstick) | 1 |
| 10***19 | Gauge-Oil Level (Dipstick) | 1 |
| 1S***63 | Plug; (Mounted-Bottom | 3 |
7c-2475 Lines Gp-Engine Oil
| 3P***56 | Seal-O-Ring; (21.82mm Id) | 2 |
| 4W***32 | Elbow-Outlet | 1 |
| 6V***40 | Bolt (M8x1.25x25mm); (M8x1.25x25-mm) | 4 |
4p-7703 Lines Gp-Turbocharger Oil
| 11***19 | Tube As | 1 |
| 1S***57 | Gasket; (Turbocharger-Oil Supply) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
2w-8625 Pump Gp-Engine Oil
| 2W***77 | Body As-Oil Pump | 1 |
| 2W***78 | Plunger-Relief | 1 |
| 2W***79 | Washer; (8.5x9.5x1.6-mm Thk) | 1 |
119-2924 Pump Gp-Engine Oil
| 10***05 | Spring | 1 |
| 11***24 | Pump Group-Engine Oil | 1 |
| 2W***77 | Body As-Oil Pump | 1 |
4w-2195 Pump Gp-Engine Oil
| 2W***25 | Pump Group-Engine Oil | 1 |
| 4W***95 | Pump Group-Engine Oil; Engine Oil Pump Group | 1 |
| 6V***15 | Bolt; (M10x1.5x75-mm) | 2 |
2t-2951 Valve Gp-Fluid Sampling
| 2T***51 | Valve Group-Fluid Sampling; Manual Valve Group (Fluid Sampling) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
Operator Station
3t-7068 Motor Gp-Window Wiper -Rear
| 3C***84 | Screw-Machine; (M5x0.8 Bg Thd) | 4 |
| 3T***59 | Bracket | 1 |
| 3T***68 | Wiper Group-Windshield; -Rear | 1 |
3t-7066 Wiper Gp-Window -Front
| 3C***84 | Screw-Machine; (M5x0.8 Bg Thd) | 4 |
| 3T***59 | Bracket | 1 |
| 3T***66 | Wiper Group-Windshield; -Front | 1 |
106-6441 Air Conditioner Ar
| 10***58 | Lines Group-Air Conditioner; Air Conditioner Lines Group | 1 |
| 10***41 | Air Conditioner Ar | 1 |
| 10***81 | Air Conditioner Group; Air Conditioner Group | 1 |
106-7281 Air Conditioner Gp
| 06***93 | Grommet; (Rh) | 1 |
| 10***65 | Heater Group-Cab | 1 |
| 10***70 | Grommet | 1 |
8y-4200 Armrest Gp -Rh
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 1K***72 | Locknut Horn To Guard | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 1 |
8y-6000 Armrest Gp -Lh
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 1K***72 | Locknut Horn To Guard | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 1 |
8y-5904 Armrest Gp
| 3E***12 | Nut-Square; (3/8-16-Thd) | 1 |
| 6V***87 | Screw-Pan Head; (10-24x1-In) | 4 |
| 8S***03 | Ring-Retaining | 1 |
116-6884 Cab Ar
| 10***97 | Installation Group-Radio | 1 |
| 10***43 | Rops Group-Enclosed | 1 |
| 10***44 | Panel Group-Instrument | 1 |
106-2357 Cab Ar
| 10***97 | Installation Group-Radio | 1 |
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***57 | Cab Ar | 1 |
121-7905 Cab Ar -Enclosed
| 10***21 | Film-Identification; (Caterpillar)(Caterpillar)(Front) | 1 |
| 10***44 | Panel Group-Instrument | 1 |
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
121-7908 Cab Gp-Non-Rops -Enclosed
| 10***61 | Guard | 1 |
| 10***11 | Screw-Machine; (3/8-16x0.75-In) | 1 |
| 12***08 | Cab Group-Non-Rops; -Enclosed | 1 |
122-8363 Cab Gp-Non-Rops
| 12***14 | Glass; (Front Quarter) | 2 |
| 12***16 | Glass; (Front) | 1 |
| 12***17 | Glass; (Rear) | 1 |
117-1389 Canopy Ar-Open Rops
| 10***74 | Guard Group-Vandalism; Vandalism Guard Group | 1 |
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
106-2436 Canopy Ar-Open Rops
| 10***74 | Guard Group-Vandalism; Vandalism Guard Group | 1 |
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
3e-1909 Compressor Gp-Refrigerant
| 3E***09 | Compressor Group-Clutch & Refrigerant | 1 |
| 3E***58 | Compressor Group-Refrigerant | 1 |
| 7T***32 | Plug Assem.; (3/8-24) | 1 |
106-7146 Compressor Gp-Refrigerant
| 10***46 | Compressor Group-Refrigerant; Refrigerant Compressor Group | 1 |
| 3E***09 | Compressor Group-Clutch & Refrigerant | 1 |
| 7C***41 | Plate | 1 |
106-5122 Compressor Gp-Refrigerant
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***22 | Compressor Group-Refrigerant; -Air Conditioner | 1 |
| 18***39 | Pin-Connector; (14-Ga To 18-Ga)(For 14 Gauge Wire) | 2 |
116-6267 Compressor Gp-Refrigerant
| 10***22 | Compressor Group-Refrigerant; -Air Conditioner | 1 |
| 11***67 | Compressor Group-Refrigerant | 1 |
| 12***77 | Guard As-Compressor Pulley | 1 |
107-6732 Condenser & Mtg Gp-Refrigerant
| 10***98 | Bracket | 2 |
| 10***32 | Condenser & Mtg Group-Refrigerant | 1 |
| 12***13 | Condenser | 1 |
112-1572 Control Gp-Monitor -Payload
| 11***72 | Control Group; -Payload | 1 |
| 16***75 | Control Group-Monitor; -Payload | 1 |
165-4075 Control Gp-Monitor -Payload
| 10***85 | Battery; (Lithium)(Internal Backup) | 1 |
| 12***90 | Cover; (Serv Repair) | 1 |
| 16***75 | Control Group-Monitor; -Payload | 1 |
100-5778 Control Gp-Monitor -Caterpillar Monitoring System
| 10***78 | Control Group-Monitor; -Caterpillar Monitoring System | 1 |
| 15***67 | Control Group-Monitor; -Caterpillar Monitoring System | 1 |
147-6976 Control Gp-Monitor -Payload
| 10***85 | Battery; (Lithium)(Internal Backup) | 1 |
| 12***90 | Cover; (Serv Repair) | 1 |
| 14***76 | Control Group-Monitor; -Payload | 1 |
103-5526 Control Gp-Monitor -Dimmer
| 10***26 | Control Group-Monitor Sys Dimmer; -Backlight Dimmer | 1 |
| 3E***83 | Wedge-Receptacle Lock; (6-Pin) | 1 |
| 5P***32 | Screw-Washer Head; 4.76mm(.187in)Long | 2 |
9u-1434 Control Gp-Pilot Operated Hyd -3-Function
| 10***10 | Sheet | 1 |
| 10***11 | Gasket | 1 |
| 10***53 | Valve-Ball; (90-Deg, 3/4-16-Thd)(Implement Lockout) | 1 |
9u-0510 Control Gp-Pilot Operated Hyd -2-Function
| 10***10 | Sheet | 1 |
| 10***11 | Gasket | 1 |
| 10***01 | Screw-Machine; (M5x0.8x25-mm) | 1 |
106-2359 Control Gp-Steering
| 10***96 | Plate | 2 |
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 11***47 | Support As | 1 |
107-6219 Control Gp-Transmission
| 10***19 | Control Group-Transmission | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 6 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 9 |
108-3029 Control Gp-Transmission
| 10***19 | Control Group-Transmission | 1 |
| 10***56 | Cover-Shift | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
136-7823 Control Gp-Transmission
| 13***23 | Control Group-Transmission | 1 |
| 6V***73 | Screw; (Machine) (M5x0.8x12mm) | 4 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 6 |
106-0621 Dash Gp
| 10***21 | Dash Group; Dash Group | 1 |
| 10***23 | Dash | 1 |
| 8T***01 | Bolt-Locking; (M10x1.5x20-mm) | 8 |
9c-8240 Duct & Control Gp
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 20 |
| 11***59 | Cable Assem. | 1 |
| 11***59 | Duct As-Output | 1 |
8y-5959 Extension Gp-Backrest -Vinyl
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***47 | Fastener | 2 |
| 8Y***59 | Extension Group-Backrest | 1 |
8y-5874 Extension Gp-Backrest -Cloth
| 8Y***74 | Extension Group-Backrest; Backrest Extension Group | 1 |
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***43 | Cushion Kit; (Consists Of Fastener, Cushion Assem.) | 1 |
104-7174 Guard Gp-Vandalism
| 10***74 | Guard Group-Vandalism; Vandalism Guard Group | 1 |
| 10***77 | Cover | 1 |
| 10***80 | Cover | 1 |
116-8743 Handhold Gp
| 11***43 | Handhold Group | 1 |
| 7X***72 | Washer-Hard; (10.2x25.5x2.5-mm Thk) | 4 |
| 8T***36 | Capscrew; (Hex Hd) (M10 X 1.50 X 25l Gr 10.9) | 4 |
9c-8239 Heater Gp-Cab
| 10***65 | Heater Group-Cab | 1 |
| 8T***44 | Bolt-Plt; (M6 X 1.0 X 70) | 3 |
| 8T***38 | Bolt-Plt; (M6 X 1.0 X 20) | 4 |
100-3965 Heater Gp-Cab
| 10***65 | Heater Group-Cab | 1 |
| 10***71 | Support Assem. | 1 |
| 10***73 | Clamp Assem. | 1 |
108-4582 Housing Gp-Seat Suspension
| 09***78 | Pin-Spring | 1 |
| 10***24 | Kit-Indicator; (Weight Adjustment)(Suspension Seat) | 1 |
| 10***79 | Kit-Bumper; (Weight Adjustment)(Suspension Seat) | 1 |
4e-8464 Installation Gp-Gov Control
| 1H***37 | Bolt-Mount 9w***75 Fuel Level Sensor | 1 |
| 1V***41 | Seal | 1 |
| 4E***64 | Installation Group-Gov Control; Installation Control Group (Governor And Hydraulic) | 1 |
101-2497 Installation Gp-Radio
| 10***97 | Installation Group-Radio | 1 |
| 10***40 | Cable As-Coaxial | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 5 |
9u-4400 Liner Gp-Cab
| 3W***41 | Washer; (16x75x3.5-mm Thk) | 14 |
| 4E***44 | Insulattion | 1 |
| 4E***45 | Button | 14 |
9u-2281 Liner Gp-Cab
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 4 |
| 10***22 | Bracket Assem. | 1 |
| 4B***40 | Screw-Machine; (10-32x1-In) | 3 |
106-3458 Lines Gp-Air Conditioner
| 10***89 | Accumulator-Air Conditioner, . Gear; Ring | 1 |
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 2 |
| 10***58 | Lines Group-Air Conditioner; Air Conditioner Lines Group | 1 |
4e-8479 Lines Gp-Cab Heater
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 4 |
| 4E***79 | Lines Group-Cab Heater | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 2 |
6v-1970 Literature Gp
| 2Y***09 | Seal-Wire | 2 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
| 6V***70 | Literature Group; (Literature Compartment) | 1 |
8r-1923 Mirror Gp-Lh
| 5P***76 | Mirror | 1 |
| 6C***80 | Tube As | 1 |
| 7J***28 | Clip; (Tab)(Straight) | 2 |
8r-1924 Mirror Gp-Rh
| 5P***76 | Mirror | 1 |
| 6C***41 | Tube As | 1 |
| 7J***28 | Clip; (Tab)(Straight) | 2 |
8r-1922 Mirror Gp-Rear View
| 8R***22 | Mirror Group-Rear View | 1 |
| 8R***23 | Mirror Group | 1 |
| 8R***24 | Mirror Group | 1 |
9c-8243 Mirror Gp-Rear View
| 4E***60 | Bracket | 2 |
| 5P***72 | Mirror As; (Interior, Front) | 2 |
| 8T***38 | Bolt-Plt; (M6 X 1.0 X 20) | 4 |
100-5895 Module Gp-Quad Gauge
| 10***95 | Module Group-Quad Gauge; (Quad Gauge Module) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 3E***83 | Wedge-Receptacle Lock; (6-Pin) | 1 |
153-8061 Module Gp-Speedometer & Tach
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 10***10 | Kit-Connecting Plug; (6-Pin) | 1 |
| 15***61 | Module Group-Speedometer & Tach | 1 |
100-5888 Module Gp-Speedometer & Tach
| 10***88 | Module Group-Speedometer & Tach | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 3E***83 | Wedge-Receptacle Lock; (6-Pin) | 1 |
102-8737 Monitor Ar-Payload
| 10***37 | Monitor Ar-Payload | 1 |
| 10***38 | Wiring Group-Payload Sensor | 1 |
| 10***67 | Monitor Group-Payload; Operator Monitor Group | 1 |
126-3506 Monitor Ar-Payload
| 10***38 | Wiring Group-Payload Sensor | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***75 | Monitor Group-Payload | 1 |
130-5197 Monitor Ar-Payload
| 10***38 | Wiring Group-Payload Sensor | 1 |
| 13***56 | Monitor Group-Payload | 1 |
| 13***97 | Monitor Ar-Payload | 1 |
124-1775 Monitor Gp-Payload
| 10***91 | Cover | 1 |
| 10***35 | Harness As | 1 |
| 12***75 | Monitor Group-Payload | 1 |
130-4856 Monitor Gp-Payload
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***72 | Control Group; -Payload | 1 |
| 12***38 | Bracket Assembly | 1 |
108-6967 Monitor Gp-Payload
| 10***91 | Cover | 1 |
| 10***35 | Harness As | 1 |
| 10***29 | Floor Mat | 1 |
116-6888 Mounting Gp-Cab
| 10***89 | Strip | 1 |
| 10***97 | Plate | 2 |
| 10***36 | Box Assem. | 1 |
121-7923 Mounting Gp-Cab
| 10***97 | Plate | 2 |
| 10***36 | Box Assem. | 1 |
| 10***00 | Strip | 1 |
107-1731 Mounting Gp-Cab
| 10***89 | Strip | 1 |
| 10***97 | Plate | 2 |
| 10***31 | Mounting Group-Cab | 1 |
106-0626 Mounting Gp-Platform
| 10***97 | Plate | 2 |
| 10***00 | Strip | 1 |
| 10***26 | Mounting Group-Platform; Platform Mounting Group | 1 |
117-1392 Mounting Gp-Platform
| 10***96 | Handle As; (Lh)(Lh) | 1 |
| 10***88 | Strip | 1 |
| 10***97 | Plate | 2 |
107-1735 Mounting Gp-Platform
| 10***97 | Plate | 2 |
| 10***00 | Strip | 1 |
| 10***34 | Floor Mat | 1 |
122-3829 Mounting Gp-Platform
| 10***88 | Strip | 1 |
| 10***97 | Plate | 2 |
| 10***36 | Box Assem. | 1 |
108-9426 Operator Ar
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***36 | Canopy Ar-Open Rops | 1 |
121-7904 Operator Ar -Enclosed
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
123-4581 Operator Ar -Semi-Cab
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
123-3899 Operator Ar -Open
| 11***73 | Canopy Group-Non-Rops | 1 |
| 12***73 | Operator Ar-Non-Rops | 1 |
| 12***99 | Operator Ar; -Open | 1 |
123-4580 Operator Ar
| 12***63 | Cab Group-Non-Rops | 1 |
| 12***72 | Washer Group-Window | 1 |
| 12***73 | Wiper Group-Window | 1 |
108-9425 Operator Ar
| 03***91 | Pop - Rivet (To Secure Safety Lable) | 4 |
| 09***62 | Washer; (Hard) (3.4x7x0.8mm Thk) | 4 |
| 10***21 | Film-Identification; (Caterpillar)(Caterpillar)(Front) | 1 |
106-2354 Operator Ar
| 10***54 | Operator Ar | 1 |
| 10***57 | Cab Ar | 1 |
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
106-3058 Operator Ar
| 10***26 | Mounting Group-Platform; Platform Mounting Group | 1 |
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
116-6885 Operator Ar
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
122-3673 Operator Ar-Non-Rops
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
122-3676 Operator Ar-Non-Rops
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
117-1390 Operator Ar-Open Rops
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***29 | Control Group-Transmission; Transmission Control Group | 1 |
106-2434 Operator Ar-Open Rops
| 10***59 | Control Group-Steering; Steering Control Group | 1 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***34 | Operator Ar-Open Rops | 1 |
8y-5992 Pan Gp-Seat
| 3K***97 | Pin 3.18 mm(.125 In.) Diameter | 4 |
| 6V***56 | Ring-Retaining | 2 |
| 8Y***92 | Pan As-Seat; (Bottom) | 1 |
111-3779 Panel Gp-Instrument
| 10***25 | Cushion Assem., . Collar | 1 |
| 10***13 | Tray | 1 |
| 10***29 | Harness As; (Key Switch-Center Panel)(Floodlight) | 1 |
104-1744 Panel Gp-Instrument
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 10***25 | Cushion Assem., . Collar | 1 |
| 10***28 | Panel As-Switch; (Center) | 1 |
116-6882 Panel Gp-Instrument
| 03***28 | Grommet | 1 |
| 10***68 | Bezel | 1 |
| 10***78 | Control Group-Monitor; -Caterpillar Monitoring System | 1 |
107-6363 Panel Gp-Instrument
| 03***28 | Grommet | 1 |
| 10***30 | Film-Face | 1 |
| 10***31 | Film-Face | 1 |
107-3026 Panel Gp-Instrument
| 06***09 | Screw; (8-32x0.75-In) | 2 |
| 10***25 | Cushion Assem., . Collar | 1 |
| 10***13 | Tray | 1 |
106-2361 Panel Gp-Instrument
| 03***28 | Grommet | 1 |
| 10***30 | Film-Face | 1 |
| 10***31 | Film-Face | 1 |
107-1707 Panel Gp-Instrument
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 06***09 | Screw; (8-32x0.75-In) | 4 |
| 10***23 | Console | 1 |
117-1393 Panel Gp-Instrument
| 03***28 | Grommet | 1 |
| 10***68 | Bezel | 1 |
| 10***78 | Control Group-Monitor; -Caterpillar Monitoring System | 1 |
122-8366 Panel Gp-Instrument
| 10***25 | Cushion Assem., . Collar | 1 |
| 10***13 | Tray | 1 |
| 10***29 | Harness As; (Key Switch-Center Panel)(Floodlight) | 1 |
106-2360 Pedal Gp-Governor
| 03***16 | Bolt-Self Locking; (1/4unc X 3/4) | 3 |
| 10***60 | Pedal Group-Governor; Governor Pedal Group | 1 |
| 10***33 | Pedal | 1 |
6v-6561 Wiper Pivot Gp
| 6A***18 | Washer; (8.1x12.5x1-mm Thk) | 1 |
| 6V***07 | Shaft As; (Pivot) | 1 |
| 6V***09 | Cap-Wiper | 1 |
122-3674 Platform Ar
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
| 10***36 | Seat Group-Suspension | 1 |
123-4582 Platform Ar
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
| 10***36 | Seat Group-Suspension | 1 |
122-3677 Platform Ar
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
| 10***36 | Seat Group-Suspension | 1 |
106-3060 Platform Ar
| 10***48 | Control Group-Parking Brake; Parking Brake Control Group | 1 |
| 10***21 | Dash Group; Dash Group | 1 |
| 10***60 | Platform Ar | 1 |
106-3062 Platform Gp
| 10***02 | Sheet As | 1 |
| 10***05 | . Bearing., Sheet As,.. Bearing. | 1 |
| 10***27 | Threshold As | 1 |
7i-3883 Platform Gp
| 3E***05 | Seal (Order By cm) 7cm | 0 |
| 3P***04 | Stud-Weld (1/4-20x.620in Oal) | 5 |
| 4E***15 | Handle-Grab | 1 |
114-8153 Platform Gp-Cab
| 11***62 | Plate Assem. | 1 |
| 11***79 | Gasket | 1 |
| 11***53 | Platform Group-Cab | 1 |
121-7906 Platform Gp-Non-Rops -Enclosed Cab
| 09***13 | Spacer | 1 |
| 10***01 | Sheet As | 1 |
| 10***28 | Sheet As | 1 |
104-1743 Rops Gp-Enclosed
| 10***43 | Rops Group-Enclosed | 1 |
| 10***29 | Glass; (Left Rear Quarter) | 1 |
| 10***30 | Glass; (Right Rear Quarter) | 1 |
106-3034 Rops Gp-Enclosed
| 09***13 | Spacer | 1 |
| 10***76 | Insulation | 1 |
| 10***34 | Rops Group-Enclosed | 1 |
111-4892 Rops Gp-Open
| 11***62 | Plate Assem. | 1 |
| 11***79 | Gasket | 1 |
| 11***91 | Canopy As | 1 |
106-3051 Rops Gp-Open
| 10***96 | Handle As; (Lh)(Lh) | 1 |
| 10***51 | Rops Group-Open | 1 |
| 10***52 | Canopy As | 1 |
122-4617 Seat Belt Gp -Retractable
| 12***17 | Seat Belt Group; -Retractable-Operator | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 4D***32 | Locknut (7/16-20 Thd) | 1 |
8y-3792 Seat Belt Gp -Retractable
| 8S***34 | Locknut; (Flange) (7/16-20 Thd) | 1 |
| 8T***60 | Washer-Hard (For Use With 7/16 In Bolts) | 1 |
| 8Y***92 | Seat Belt Group; -Retractable-Operator | 1 |
8y-5976 Seat Gp
| 06***03 | Shim (.060mm Thk); (1.52-mm Thk) | 4 |
| 09***78 | Pin-Spring | 1 |
| 11***77 | Kit-Seat Knob; (Includes Knobs & Screws) | 1 |
8y-6918 Seat Gp
| 12***17 | Seat Belt Group; -Retractable-Operator | 1 |
| 8Y***00 | Armrest Group | 1 |
| 8Y***74 | Extension Group-Backrest; Backrest Extension Group | 1 |
8y-5986 Seat Gp -Cloth
| 06***03 | Shim (.060mm Thk); (1.52-mm Thk) | 4 |
| 09***78 | Pin-Spring | 1 |
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
101-9079 Seat Gp-Suspension
| 10***79 | Seat Group-Suspension | 1 |
| 4F***79 | Bolt Clip To Tube Assembly (Aftercooler Radiator Inlet) | 1 |
| 6N***89 | Circuit Breaker As; (15-Ampere)(Air Conditioning Compressor) | 1 |
107-5834 Seat Gp-Suspension
| 10***27 | Seat Group-Suspension | 1 |
| 10***34 | Seat Group-Suspension | 1 |
| 8T***96 | Washer-Hard- Line From Pipe As. To Gear | 4 |
107-5827 Seat Gp-Suspension
| 10***27 | Seat Group-Suspension | 1 |
| 4F***79 | Bolt Clip To Tube Assembly (Aftercooler Radiator Inlet) | 1 |
| 8Y***92 | Seat Belt Group; -Retractable-Operator | 1 |
107-5828 Seat Gp-Suspension
| 10***28 | Seat Group-Suspension | 1 |
| 10***82 | Suspension Group-Seat; -Contour-Shock Absorber | 1 |
| 4F***79 | Bolt Clip To Tube Assembly (Aftercooler Radiator Inlet) | 1 |
107-5836 Seat Gp-Suspension
| 10***28 | Seat Group-Suspension | 1 |
| 10***36 | Seat Group-Suspension | 1 |
| 8T***96 | Washer-Hard- Line From Pipe As. To Gear | 4 |
9u-2282 Suppression Gp-Cab Sound
| 09***65 | Spacer; (17x40x3-mm Thk) | 10 |
| 10***78 | Insulation | 1 |
| 10***30 | Insulation | 1 |
111-4681 Suppression Gp-Cab Sound
| 09***65 | Spacer; (17x40x3-mm Thk) | 10 |
| 10***78 | Insulation | 1 |
| 10***30 | Insulation | 1 |
119-7027 Suspension Gp-Seat -Air
| 10***17 | Bumper | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***27 | Suspension Group-Seat; -Air | 1 |
8y-6801 Suspension Gp-Seat
| 10***08 | Kit-Fastener; (Incl Parts Marked V) | 1 |
| 10***17 | Bumper | 4 |
| 2K***73 | Locknut Inside Guard Assembly | 6 |
8y-5888 Suspension Gp-Seat
| 10***03 | Fastener | 26 |
| 10***94 | Kit-Tether Belt; (Suspension Seat)(Seat Suspension) | 1 |
| 10***95 | Kit-Suspension Roller; (Suspension Seat)(Seat Suspension) | 1 |
108-4082 Suspension Gp-Seat
| 10***03 | Fastener | 23 |
| 10***94 | Kit-Tether Belt; (Suspension Seat)(Seat Suspension) | 1 |
| 10***95 | Kit-Suspension Roller; (Suspension Seat)(Seat Suspension) | 1 |
8r-1774 Tank Gp-Window Washer
| 3W***98 | Cap; (Window Washer Tank Fill) | 1 |
| 3W***99 | Packing | 1 |
| 7T***90 | Pump As; (Washer) | 2 |
122-8372 Washer Gp-Window
| 12***72 | Washer Group-Window | 1 |
| 2R***04 | Nut-Self Lock; (5/16unc) | 1 |
| 3V***91 | Grommet | 1 |
4e-8480 Washer Gp-Window
| 2R***04 | Nut-Self Lock; (5/16unc) | 1 |
| 3V***91 | Grommet | 1 |
| 4E***80 | Washer Group-Window | 1 |
121-3572 Wiper Gp-Window
| 10***35 | Wiper Group-Window; -Rear | 1 |
| 12***72 | Wiper Group-Window | 1 |
| 2V***16 | Clip; (9.52mm Id) | 11 |
3e-7512 Wiper Gp-Window -Front
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 3C***84 | Screw-Machine; (M5x0.8 Bg Thd) | 4 |
| 3E***83 | Wedge-Receptacle Lock; (6-Pin) | 1 |
4e-8463 Wiper Gp-Window
| 2V***16 | Clip; (9.52mm Id) | 11 |
| 3D***61 | Bolt; (1/4-28x1.875-In) | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
122-8373 Wiper Gp-Window
| 12***73 | Wiper Group-Window | 1 |
| 2V***16 | Clip; (9.52mm Id) | 7 |
| 3D***61 | Bolt; (1/4-28x1.875-In) | 1 |
100-7335 Wiper Gp-Window -Rear
| 10***35 | Wiper Group-Window; -Rear | 1 |
| 3C***84 | Screw-Machine; (M5x0.8 Bg Thd) | 4 |
| 3T***59 | Bracket | 1 |
Power Train
7v-3842 Spider & Bearing Gp
| 02***87 | Fitting-Grease; (Universal Joint) | 1 |
| 0L***38 | Bolt; (3/8-24x0.5-In) | 4 |
| 6W***81 | Strap-Locking | 2 |
9c-8179 Axle Ar-Fixed
| 14***14 | Differential Group | 1 |
| 9C***76 | Gear Group-Bevel | 1 |
| 9C***78 | Brake & Planetary Group | 1 |
8r-1445 Axle Ar-Oscillating -Rear
| 14***14 | Differential Group | 1 |
| 8R***45 | Axle Ar-Oscillating | 1 |
| 8R***46 | Housing Group-Oscillating Axle | 1 |
9c-8178 Brake & Planetary Gp
| 13***45 | Pin-Spring | 3 |
| 14***44 | Seal Assem. | 1 |
| 1F***51 | Dowel | 3 |
8e-4493 Case & Parts Gp-Planetary
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 5 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 11 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 10 |
6i-9853 Control Gp-Transmission Hyd
| 10***29 | Retainer | 1 |
| 10***30 | Gasket | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
7e-3452 Cooler Gp-Transmission Oil
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 12 |
| 12***37 | Core As; (Transmission Oil) | 1 |
| 2S***95 | Gaskets | 2 |
7k-5636 Cover Gp-Xmsn Oil Filler Cap
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
| 2J***61 | Ring-Retaining | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
107-5666 Cover Gp-Shipping
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 14 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 6 |
4e-3940 Differential Ar -Limited Slip
| 14***65 | Differential Group-Limited Slip | 2 |
| 4E***40 | Differential Ar; -Limited Slip | 1 |
9c-8171 Differential Gp
| 13***05 | Washer-Thrust | 4 |
| 16***72 | Washer-Thrust | 2 |
| 5V***74 | Spider | 1 |
143-9514 Differential Gp
| 13***05 | Washer-Thrust | 4 |
| 14***14 | Differential Group | 1 |
| 16***72 | Washer-Thrust | 2 |
103-2007 Differential Gp-Limited Slip
| 10***07 | Differential Group-Limited Slip | 1 |
| 10***51 | Gear-Differential; (16 Teeth) | 2 |
| 10***53 | Pinion-Bevel; (10 Teeth) | 4 |
144-4465 Differential Gp-Limited Slip
| 10***51 | Gear-Differential; (16 Teeth) | 2 |
| 10***53 | Pinion-Bevel; (10 Teeth) | 4 |
| 10***54 | Shaft-Pinion | 2 |
8r-9834 Differential Gp-Nospin
| 8R***33 | Differential Group-Nospin | 1 |
| 8R***34 | Differential Group-Nospin | 1 |
8r-9833 Differential Gp-Nospin
| 3V***05 | Spring-Conical | 2 |
| 3V***06 | Retainer | 2 |
| 3V***08 | Holdout Ring & Clutch As | 2 |
128-0745 Differential Gp-Nospin
| 12***45 | Differential Group-Nospin | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
| 8R***40 | Case Assembly | 1 |
128-0746 Differential Gp-Nospin
| 12***45 | Differential Group-Nospin | 1 |
| 12***46 | Differential Group-Nospin | 1 |
4e-3042 Filler Gp-Power Train Oil
| 4B***82 | Ball; (9.52mm) | 1 |
| 4D***86 | Clip (Right Hand Mounted) | 2 |
| 4E***42 | Filler Group-Power Train Oil | 1 |
3v-0143 Filter & Lines Gp-Transmission
| 1P***03 | Seal - Rectangular (31.86mm Id) | 1 |
| 1P***77 | Flange-Half (For Tilt Ports On Valve) | 8 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 2 |
8e-4269 Filter Gp-Oil
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 2 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6Y***30 | Housing-Filter | 1 |
9c-8176 Gear Gp-Bevel & Pinion
| 03***60 | Cup-Roller Bearing | 1 |
| 03***61 | Cone-Roller Bearing | 1 |
| 1J***60 | Cup-Bearing; (Tapered) | 1 |
8e-9090 Gear Gp-Output Transfer
| 0L***58 | Bolt 8.26cm (3.25 In.) Long | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 12 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 1 |
148-5644 Gear Gp-Output Transfer
| 0L***58 | Bolt 8.26cm (3.25 In.) Long | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 12 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 1 |
9c-8180 Housing Gp-Fixed Axle
| 12***03 | Seal-Lip Type; (7602mm Id) | 1 |
| 13***03 | Housing As-Fixed | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
8r-1446 Housing Gp-Oscillating Axle
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 4 |
| 10***31 | Plate | 1 |
| 12***03 | Seal-Lip Type; (7602mm Id) | 1 |
8r-5352 Lines Gp-Torque Conv Cooler
| 10***84 | Tube Assem. | 1 |
| 11***06 | Tube Assem. | 1 |
| 11***07 | Tube Assem. | 1 |
128-0678 Mounting Gp-Rim
| 12***78 | Mounting Group-Rim | 1 |
| 6V***37 | Plain Washer - Hardened | 20 |
| 8T***80 | Bolt; (M24x3x60-mm) | 20 |
112-5530 Planetary Gp-Transmission
| 03***60 | Ring-Retaining | 3 |
| 0L***58 | Bolt 8.26cm (3.25 In.) Long | 1 |
| 11***30 | Planetary Group-Transmission | 1 |
154-8232 Power Train Ar
| 14***54 | Shaft Group-Drive | 1 |
| 14***30 | Brake Group-Parking | 1 |
| 15***18 | Transmission Ar | 1 |
114-3457 Power Train Ar
| 10***34 | Brake Group-Parking | 1 |
| 11***31 | Transmission Ar | 1 |
| 11***57 | Power Train Ar | 1 |
6t-3651 Pump Gp-Transmission
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 6 |
| 1H***74 | Dowel (.5" Long) | 2 |
| 3P***98 | Bearing-Sleeve | 2 |
123-3472 Pump Gp-Transmission
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 6 |
| 12***60 | Body As-Oil Pump | 1 |
| 12***72 | Pump Group-Transmission | 1 |
127-4734 Rim Ar
| 12***34 | Rim Ar | 1 |
| 12***35 | Rim Group-Demountable | 4 |
| 12***78 | Mounting Group-Rim | 1 |
127-4763 Rim Ar
| 12***63 | Rim Ar | 1 |
| 12***64 | Rim Group-Demountable | 4 |
| 12***78 | Mounting Group-Rim | 1 |
133-7444 Rim Gp-Demountable
| 13***83 | Rim As | 1 |
| 13***44 | Rim Group-Demountable | 1 |
| 1J***87 | Flange | 2 |
127-4764 Rim Gp-Demountable
| 12***64 | Rim Group-Demountable | 1 |
| 2D***43 | Seal-O-Ring | 1 |
| 2D***11 | Valve Group-Tire | 1 |
8r-0099 Rim Gp-Demountable -4 Required
| 1J***87 | Flange | 2 |
| 2D***43 | Seal-O-Ring | 1 |
| 2D***07 | Stud | 1 |
127-4735 Rim Gp-Demountable
| 12***35 | Rim Group-Demountable | 1 |
| 1J***87 | Flange | 2 |
| 2D***43 | Seal-O-Ring | 1 |
8y-0782 Shaft Gp-Drive
| 0L***15 | Bolt 88.90 mm(3.50 In.) N.F. | 1 |
| 2H***88 | Seal-O-Ring; (50.17mm Id) | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
145-7054 Shaft Gp-Drive
| 14***54 | Shaft Group-Drive | 1 |
| 14***55 | Yoke As | 1 |
| 14***56 | Universal Joint Group | 1 |
145-7058 Slip Joint Gp
| 14***58 | Slip Joint Group | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
| 4K***77 | Fitting-Pressure Relief | 1 |
127-4718 Tire & Rim Ar
| 12***18 | Tire & Rim Ar | 1 |
| 12***34 | Rim Ar | 1 |
133-0779 Tire & Rim Ar
| 12***34 | Rim Ar | 1 |
| 13***79 | Tire & Rim Ar | 1 |
133-0780 Tire & Rim Ar
| 12***34 | Rim Ar | 1 |
| 13***80 | Tire & Rim Ar | 1 |
133-0782 Tire & Rim Ar
| 12***63 | Rim Ar | 1 |
| 13***82 | Tire & Rim Ar | 1 |
133-0781 Tire & Rim Ar
| 12***63 | Rim Ar | 1 |
| 13***81 | Tire & Rim Ar | 1 |
127-4720 Tire & Rim Ar
| 12***20 | Tire & Rim Ar | 1 |
| 12***34 | Rim Ar | 1 |
119-0830 Tire Gp
| 11***30 | Tire Group | 1 |
| 12***63 | Rim Ar | 1 |
119-0829 Tire Gp
| 11***29 | Tire Group | 1 |
| 12***63 | Rim Ar | 1 |
8e-7756 Torque Converter & Housing Gp
| 0L***58 | Bolt 8.26cm (3.25 In.) Long | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
1t-1939 Torque Converter Gp
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 24 |
| 1P***04 | Plug-Metal Cup | 2 |
| 1T***13 | Ring-Lock | 2 |
112-5531 Transmission Ar
| 10***66 | Cover Group-Shipping | 1 |
| 11***30 | Planetary Group-Transmission | 1 |
| 11***31 | Transmission Ar | 1 |
153-3718 Transmission Ar
| 10***66 | Cover Group-Shipping | 1 |
| 11***30 | Planetary Group-Transmission | 1 |
| 12***72 | Pump Group-Transmission | 1 |
145-7056 Universal Joint Gp
| 14***56 | Universal Joint Group | 1 |
| 7V***42 | Spider & Bearing Group | 1 |
8y-0787 Universal Joint Gp
| 2H***37 | Bolt 1.59 cm(.625 In.) Long; Bolt-- Generator Line Leads | 4 |
| 5P***34 | Fitting-Hydraulic | 1 |
| 6W***26 | Strap-Locking | 2 |
8y-0783 Universal Joint Gp
| 2H***37 | Bolt 1.59 cm(.625 In.) Long; Bolt-- Generator Line Leads | 4 |
| 5P***34 | Fitting-Hydraulic | 1 |
| 6W***26 | Strap-Locking | 2 |
3s-2695 Valve Gp-Relief -Torque Converter Outlet
| 06***40 | Seal-O-Ring (Id=37.69mm) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 2S***82 | Spring | 1 |
8e-5158 Valve Gp-Selector
| 2B***95 | Cap Screw--Tube Assembly To Air Inlet Pipe | 2 |
| 2S***72 | Stop | 1 |
| 5P***61 | Ring-Retaining | 1 |
6i-9481 Valve Gp-Selector & Press Cont
| 2A***46 | Plug 9.80mm(.386in.)Outside Dia. | 1 |
| 2B***95 | Cap Screw--Tube Assembly To Air Inlet Pipe | 5 |
| 2H***95 | Setscrew; (10-24thd X 7/16) | 1 |
3e-3748 Valve Gp-Solenoid
| 10***83 | Kit-Seal; (Solenoid Valve) | 1 |
| 10***70 | Locknut; (1/4-20-Thd) | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
6i-9482 Valve Gp-Transmission Control
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 10***27 | Harness As-Transmission; (Shift Solenoids) | 1 |
| 1D***40 | Bolt,Machine Fuel Filter Mounting | 10 |
Service Equipment And Supplies
9g-9288 Cap Gp-Protection
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
| 2J***61 | Ring-Retaining | 1 |
| 5D***11 | Cover-Hydraulic Cap | 1 |
101-7452 Film Gp
| 10***21 | Film-Identification; (Caterpillar)(Caterpillar)(Front) | 1 |
| 10***93 | Film-Stripe-Both Sides & Across Back | 3 |
| 10***52 | Film Group | 1 |
8f-9866 Grease Gun Gp
| 2M***89 | Coupler Assem. | 1 |
| 8F***66 | Grease Gun As | 1 |
| 9F***36 | Nozzle Assem. | 1 |
7i-3701 Lock Gp-Vandalism
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 1 |
| 5P***02 | Padlock Group; (Includes: Battery Compartments, Platform Compartments, Radiator Access Door, Firewall Doors) | 6 |
| 5V***51 | Hasp (Mounted On Transmission Oil Cap Protection Cover) | 1 |
3e-6577 Plate & Film Gp
| 10***52 | Film Group | 1 |
| 10***89 | Film-- Panel (Cms) | 1 |
| 11***41 | Film-Notice | 1 |
9s-7978 Tool Gp-Hand
| 18***30 | Strap Wrench Assem. | 1 |
| 1P***45 | Gauge Group-Pressure | 1 |
| 1P***51 | Pin-Spring | 1 |
Steering System
3v-0107 Cylinder & Mtg Gp-Steering
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 2 |
| 3V***07 | Cylinder & Mounting Group | 1 |
| 3V***08 | Cylinder & Seal Group | 2 |
3v-0108 Cylinder & Seal Gp-Steering
| 3V***08 | Cylinder & Seal Group | 1 |
| 6E***92 | Cylinder Group-Steering | 1 |
| 7K***03 | Seal-Lip Facing Away From Bearing | 4 |
6e-4892 Cylinder Gp-Steering
| 16***90 | Seal As-Buffer | 1 |
| 16***00 | Seal-U-Cup | 1 |
| 16***52 | Seal-Wiper | 1 |
106-0428 Lines Gp-Steering
| 10***96 | Hose Assem. | 1 |
| 10***62 | Hose As | 1 |
| 10***28 | Lines Group-Steering | 1 |
9c-1160 Lines Gp-Secondary Steering
| 10***81 | Plate | 1 |
| 12***50 | Tube Assem. | 1 |
| 12***87 | Spacer | 1 |
5v-1237 Pump & Mtg Gp-Secondary Steer
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 1 |
| 3G***91 | Pump Group-Gear | 1 |
| 5V***37 | Pump & Mounting Group | 1 |
3g-9891 Pump Gp-Gear -Secondary Steering
| 00***14 | Ring-Retaining; (Internal) | 1 |
| 07***43 | Plate-Isolation | 2 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 8 |
6e-6406 Pump Gp-Metering
| 11***41 | Kit-Seal; (Includes 1 Seal-Dust, 1 Seal-Quad Ring & 6 Seal-O-Rings) | 1 |
| 11***16 | Kit-Coversion; (Includes 7 Bolts, 1 Spacer, & 1 End Cap To Convert From Supplier 001 To 002 Design) | 1 |
| 1H***23 | Packing,Preformed Part Of Kit P/N 5r***25 | 1 |
9u-2668 Steering Ar-Secondary
| 4E***47 | Wiring Group-Secondary Steering; Supplemental Steering Wiring Group | 1 |
| 5V***37 | Pump & Mounting Group | 1 |
| 5V***83 | Valve & Mounting Group; -Secondary Steering | 1 |
8y-7680 Steering Column Gp
| 03***01 | Knob, Part Of Valve Assembly.,. Pipe | 1 |
| 13***11 | Kit-Horn Contact | 1 |
| 13***12 | Kit-Horn Brush | 2 |
5v-5683 Valve & Mtg Gp-Diverter -Secondary Steering
| 10***10 | Plate | 1 |
| 3G***39 | Valve Group; -Secondary Steering | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 7 |
3g-0639 Valve Gp-Diverter -Secondary Steering
| 1L***18 | Spring-Shut-Off | 2 |
| 2S***78 | Seal-O-Ring (Id=37.47mm) | 1 |
| 3G***39 | Valve Group; -Secondary Steering | 1 |
9t-6874 Valve Gp-Steering
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 1T***89 | Washer; (9.93x22.22x2.54-mm Thk) | 2 |
| 2L***93 | Bolt-Socket Hd; (3/8unc X 2 1/4) | 1 |
9t-1206 Valve Gp-Makeup -Steering Lines
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 2 |
| 4B***82 | Ball; (9.52mm) | 2 |
| 4J***33 | Seal Fuel Injection Pump | 2 |
8j-1553 Valve Gp-Steering Neutralizer
| 1A***96 | Spring-Valve | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 1U***42 | Boot | 1 |
9t-1707 Valve Gp-Steering
| 11***12 | Spacer; (8.89x12.7x15-mm Thk) | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 1T***89 | Washer; (9.93x22.22x2.54-mm Thk) | 2 |
Work Tools
107-3411 Adapter Gp-Tip
9w-1376 Adapter Gp-Tip
| 3G***08 | Adapter-Strap; (Lh) | 1 |
| 3G***09 | Adapter-Strap; (Rh) | 1 |
| 4T***07 | Adapter-Strap | 6 |
9w-2238 Edge Gp-Bit & Cutting
| 3K***70 | Nut-Full (1.25 X 7 Thd) | 18 |
| 4K***84 | Washer-Hard; (34x55x6-mm Thk) | 18 |
| 7T***60 | Edge-Cutting-Rh | 1 |
3g-6341 Edge Gp-Bit & Cutting
| 1U***01 | Edge-Cutting | 2 |
| 2J***07 | Nut-Full; (1-8 X38.1 Thd) | 12 |
| 3G***41 | Bit & Cutting Edge Group; (Cutting) | 1 |
8r-8616 Bucket As-General Purpose
| 5V***83 | Corner-Rh; (R.H.) | 1 |
| 5V***84 | Corner-Lh; (L.H.) | 1 |
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
109-3636 Bucket As-General Purpose
| 10***36 | Bucket As-General Purpose | 1 |
| 4E***79 | Bar-Rh | 2 |
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
109-3637 Bucket As-General Purpose
| 10***37 | Bucket As-General Purpose | 1 |
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
| 5V***57 | Hinge As-Inner; (R.H. Inner) | 1 |
109-3635 Bucket As-General Purpose
| 10***35 | Bucket As-General Purpose | 1 |
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
| 5V***57 | Hinge As-Inner; (R.H. Inner) | 1 |
8r-8617 Bucket As-General Purpose
| 1U***04 | Adapter-Tip | 8 |
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
| 5V***57 | Hinge As-Inner; (R.H. Inner) | 1 |
8r-8618 Bucket As-Rock
| 5V***56 | Hinge As-Inner; (L.H. Inner) | 1 |
| 5V***57 | Hinge As-Inner; (R.H. Inner) | 1 |
| 5V***60 | Hinge As-Center; (R.H. Center) | 1 |
8r-8619 Bucket As-Rock
| 1U***50 | Adapter-Tip; (Center)(Center) | 2 |
| 1U***51 | Adapter-Tip; (Rh)(Rh) | 3 |
| 1U***52 | Adapter-Tip; (Lh)(Lh) | 3 |
110-0243 Bucket Gp-General Purpose
| 10***35 | Bucket As-General Purpose | 1 |
| 11***43 | Bucket Group-General Purpose | 1 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
8r-8614 Bucket Gp-General Purpose
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
| 4F***27 | Bolt-Plow; (3/4-10x57.15mm) | 8 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 8 |
110-0244 Bucket Gp-General Purpose
| 10***36 | Bucket As-General Purpose | 1 |
| 11***44 | Bucket Group-General Purpose | 1 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
110-0245 Bucket Gp-General Purpose
| 10***37 | Bucket As-General Purpose | 1 |
| 11***45 | Bucket Group-General Purpose | 1 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
8r-8612 Bucket Gp-Rock
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
| 4F***27 | Bolt-Plow; (3/4-10x57.15mm) | 8 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 8 |
8r-8611 Bucket Gp-Rock
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 8 |
| 4F***27 | Bolt-Plow; (3/4-10x57.15mm) | 8 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 8 |
132-1060 Edge Gp-Bit & Cutting
| 13***33 | End Edge | 2 |
| 13***34 | Edge-Cutting | 2 |
| 13***60 | Edge Group-Bit & Cutting | 1 |
7t-9327 Edge Gp-Cutting
| 2J***07 | Nut-Full; (1-8 X38.1 Thd) | 14 |
| 4F***42 | Bolt 7.62 cm(3 In.) Long | 14 |
| 4T***95 | Edge (Segment) | 7 |
132-1061 Edge Gp-Cutting
| 13***38 | Edge-Segment | 1 |
| 13***39 | Edge-Segment | 3 |
| 13***40 | Edge-Segment | 3 |
4t-5225 Tip Gp-Short
| 4T***25 | Tip Group | 1 |
| 8J***54 | Tip Group-Short; -J-350 | 8 |
4t-5224 Tip Gp-Long
| 4T***24 | Tip Group | 1 |
| 8J***55 | Tip Group-Long; -J-350 | 8 |
8j-4955 Tip Gp-Long
| 11***58 | Pin; (G.E.T.) | 1 |
| 11***59 | Retainer Assembly; (G.E.T.) | 1 |
| 1U***52 | Tip (Long) | 1 |
9j-3167 Tip Gp-Long
| 10***08 | Pin-G.E.T. | 1 |
| 1U***02 | Tip ( Long ) | 1 |
| 8E***59 | Retainer Assem. | 1 |
9w-8144 Tip Gp-Long
| 9J***67 | Tip Group-Long; -J-300 | 8 |
| 9W***44 | Tip Group-Long | 1 |
8j-4954 Tip Gp-Short
| 11***58 | Pin; (G.E.T.) | 1 |
| 11***59 | Retainer Assembly; (G.E.T.) | 1 |
| 1U***51 | Tips-Short | 1 |
9j-3175 Tip Gp-Short
| 10***08 | Pin-G.E.T. | 1 |
| 1U***01 | Tip ( Short ) | 1 |
| 8E***59 | Retainer Assem. | 1 |
9w-8145 Tip Gp-Short
| 9J***75 | Tip Group-Short; -J-300 | 8 |
| 9W***45 | Tip Group-Short | 1 |
950F II serial number reference
The PIN plate on a 950F II is a riveted metal tag on the left side of the front frame near the operator station; Caterpillar also stamps the PIN into the frame itself at the same spot as a backup if the plate is lost. Read the first 3 characters as the serial prefix (identifies the model/build series) and the digits that follow as the sequential unit number within that prefix.
| Prefix | Identifies | Notes |
|---|---|---|
| 8TK | 950F Series II | Earliest 950F Series II production range, dated from 1992. Fitted with the 3116 turbocharged and aftercooled diesel, rated 134 kW gross / 127 kW net (180 hp gross / 170 hp net). |
| 5SK | 950F Series II | 950F Series II production range dated to the early-to-mid 1990s. Fitted with the 3116 turbocharged diesel, rated 134 kW gross / 127 kW net (180 hp gross / 170 hp net). |
| 2LM | 950F Series II | Later 950F Series II production range, running into the late 1990s. Fitted with the 3116 turbocharged diesel, same rating as the other Series II prefixes. |
| 4DJ | 950F / 950F Series II (shared prefix, split by serial sub-range) | This prefix spans two related nameplates in the same parts-book family. The earlier plain 950F falls in roughly the 00001-01999 sub-range; the 950F Series II covers 02000-and-up (factory service literature breaks it at roughly 02000-02864 and 02865-03960). Confirm which sub-range a given unit falls in before pulling parts. Both sub-ranges use the 3116 turbocharged diesel. |
Frequently asked questions
What engine does the Caterpillar 950F II wheel loader use?
The 950F Series II uses the Cat 3116 turbocharged and aftercooled 6-cylinder diesel, a 6.6 L engine rated at 134 kW (180 hp) gross and 127 kW (170 hp) net.
What is the operating weight of the Caterpillar 950F II?
Operating weight runs roughly 16,340 to 16,563 kg (36,030 to 36,521 lb) depending on bucket and configuration, with a general-purpose bucket loader landing near the top of that range.
What replaced the Caterpillar 950F II?
Caterpillar replaced the 950F Series II with the 950G, moving the 950 platform to its next-generation loader architecture.
What 950F II owners discuss
What do operators say about gear engagement and pushing power on a 950F II power shift transmission?
Delayed or hesitant shifts into 2nd (and occasionally reverse) are a recurring complaint, most often traced to a low transmission oil level, a worn neutralizer or shift-lever switch, or a clogged transmission filter rather than the clutch packs themselves. A machine that is slow to engage cold and improves once the oil warms up usually points to fluid condition or a marginal filter, not a hard mechanical fault. Operators chasing a "falls out of gear" complaint generally traced it to the neutralizer switch or shift linkage before condemning the transmission internally. Persistent slippage or loss of drive under load that survives a fluid and filter service points to worn clutch packs and calls for a shop pressure test.
What engine quirks are commonly reported for the 3116 in 950F II service?
Black smoke under load paired with soft boost is usually an aftercooler restriction rather than a bad turbo: oil carried over from an earlier turbo failure clogs the aftercooler's fine internal fins, and a new turbocharger alone will not fix it. Owners chasing a boost complaint report that cleaning or replacing the aftercooler core resolves it where a fresh turbo did not. Chronic seep points on this engine are the oil cooler o-ring seals (easy to twist or seat wrong on reassembly), the water pump, and injector sleeves — all treated as expected wear items on a well-used engine rather than defects. A rigid oil supply line feeding the fuel governor is also a known weak point on this engine family; vibration can crack it at the fitting, and the resulting leak drains engine oil quickly, so it is worth a visual check.
Why does a 950F II with the 3116 sometimes crank but not start, or start and then die?
A solenoid that clicks but the engine won't catch usually means the solenoid itself is fine and the problem is downstream in fuel delivery, rail pressure, or air pulled into the fuel system through a cracked suction hose or loose fitting. This engine is sensitive to air in the fuel system — running air through the injectors even briefly can damage them — so an intermittent no-start, or a machine that runs a few seconds then dies, is worth chasing as a suction-side air leak before condemning the injection pump or injectors. Owners report checking rail pressure and every flexible fuel line joint before assuming a bigger failure.
What hydraulic quirks come up around steering and braking on the 950F II?
Loose or jerky steering response is commonly traced to worn pins and packing at the steering cylinder ends rather than the pump, so a full grease service of the steering and articulation points plus a fluid and filter change is the usual first step before condemning the steering pump or compensator valve. Noise or a soft pedal in the hydraulic-over-hydraulic brake system points to the brake accumulator or brake valve losing precharge or sticking. Steering and service brakes are both safety-critical systems — have your dealer verify accumulator precharge and steering relief settings rather than adjusting them without factory specs.
What wear pattern is typical for this machine type around the articulation joint and tires?
The center articulation joint carries frame movement, steering load, and repeated shock, making its pins and bushings a top wear-check item; looseness here shows up as a machine that feels vague or unstable in the frame well before a pin or bushing physically fails. Skipping the step of cleaning the grease fitting before greasing lets dirt get pushed into the pin boss, where it acts like grit and accelerates wear — a common self-inflicted cause of premature pin and bushing wear. Uneven tire wear on a loader of this type often reflects stress transmitted through the articulation system or heavy use of tight turns on hard, abrasive ground rather than a tire defect.
What electrical and sensor faults show up most on the 950F II monitor panel?
Reported faults cluster around sensors and communication rather than outright component failure: fuel level sender, coolant and hydraulic oil temperature senders, low system voltage, and switch-related faults for the downshift switch, shift lever, and ride control switch. A batch of faults appearing together often points to a loose ground, a corroded connector, or a communication fault between the powertrain and implement control modules and the cab monitor rather than several sensors failing at once. Owners generally check harness connectors and grounds for corrosion before replacing a sensor outright.
What should a buyer check on a used 950F II before purchase?
Confirm the hour meter against physical wear evidence — pin and bushing play at the articulation joint, tire wear pattern, and bucket or linkage bore wear — since well-maintained units are reported running smoothly well past typical rebuild intervals while neglected ones fail much earlier. Start the engine cold and watch for smoke and turbo lag, and check the aftercooler area for signs of oil carryover from a past turbo failure. Cycle every gear for clean, prompt engagement with no hesitation, and turn the steering lock to lock checking for wander or looseness at the articulation joint. Check the monitor panel for stored faults and confirm the control modules communicate cleanly rather than throwing intermittent codes. Verify it is a genuine Series II (electric/joystick steering, larger cab glass, lower cab height versus the first-generation 950F) since controls and cab fitment differ between the two. Because steering, service brakes, and the articulation joint are structural and safety-critical, have your dealer verify pin and bushing wear limits and brake accumulator condition before final sign-off.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 950F II part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.