Caterpillaroff-highway trucktruck
Caterpillar 773D
Maintenance schedule, common problems & OEM parts breakdown
The Cat 773D is a rigid-frame, two-axle off-highway haul truck in the roughly 40-tonne payload class, built for quarry, aggregate and mid-size mining hauling. It runs the Cat 3412E, a 12-cylinder, 27 L, turbocharged-and-aftercooled HEUI diesel rated at 509 kW (682.6 hp) gross at 2000 rpm, with net/flywheel output in the 480-485 kW (644-650 hp) range depending on the rating standard cited. Drive goes through a 7-speed, electronically controlled powershift transmission. Empty operating weight runs about 39,500 kg (87,082 lb), with a loaded gross near 99,300 kg (219,000 lb) and payload capacity around 43,600 kg (96,260 lb), varying with body style and tire spec. Cat built the 773D from roughly 1996 to 2001, positioned between the mechanically-injected 773B before it and the 773E that replaced it. Cat and body-builders offered it as a standard quarry/rock-body hauler, with water-tanker and other special-body configurations available on the same chassis.
The step up from the 773B was mainly under the hood and in the electronics. The D-series swapped mechanical unit injection for HEUI-controlled fuel delivery on the 3412E and paired it with electronic transmission control for shift quality, while a single TDTO (TO-4) specification runs through the transmission, wet brakes, final drives, hydraulics and steering to simplify the fluid inventory. Nitrogen-over-oil suspension struts double as steering kingpins up front, and a box-section frame gives easier access to powertrain components than earlier designs. The 773D shares much of its cab, wet-brake and driveline architecture with sibling trucks from the same generation, which keeps parts support broad on the used market today. It remains a common mid-life rebuild candidate: HEUI-era electronics are well understood by independent shops, driveline components carry across the family, and lower acquisition cost relative to newer electronic-drive trucks keeps it attractive for quarry and contractor fleets running moderate annual hours.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 773D specifications
Engine
| Engine model | Cat 3412E, 12-cylinder, turbocharged, air-to-air aftercooled, HEUI fuel system (TA-HEUI) |
| Displacement | 27.0 L (1,650 cu in) |
| Gross power (SAE J1995) | 509 kW (682.6 hp) |
| Net power (rated speed) | 480-485 kW (644-650 hp), rated at 2,000 rpm; figure varies slightly by spec sheet edition |
| Maximum torque | 2,314 Nm (1,706.8 lb-ft) |
| Rated engine speed | 2,000 rpm |
| Emissions tier | Not published for this generation. The 773D predates common nonroad emissions-tier labeling on published spec sheets; confirm certification for a specific serial range with a dealer if required. |
Weights
| Operating weight (empty) | 39,500 kg (87,082 lb) |
| Gross/loaded operating weight | 92,500-99,340 kg (204,000-219,007 lb); figure varies by source/spec sheet edition |
| Payload capacity (rated) | 43.7 t (96,260 lb) struck rating on most spec sheets; some references show a higher nominal rating near 48 short tons (106,500 lb) - varies by rating standard |
| Ground pressure | Not published for this machine type (rigid frame rock truck; ground pressure is not a standard catalog spec for this class) |
Dimensions
| Overall length | 9.69 m (31.8 ft) |
| Overall width | 4.46 m (14.6 ft) overall; approx. 3.93 m (12.9 ft) operating width |
| Overall height, standard | 4.02 m (13.2 ft) |
| Overall height, body raised | approx. 8.8 m (29.0 ft) |
| Wheelbase | 4.2 m (13.75 ft) |
| Ground clearance | 0.59-0.61 m (1.94-2.00 ft) |
| Inside body length | 6.49 m (21.3 ft) |
| Loading height, empty (top of tire/body rail) | 3.79 m (12.42 ft) |
| Tire size | 24.00R35 (E-4) |
Performance
| Travel speed, forward (loaded, top gear) | approx. 62-66 km/h (38.6-41 mph); varies by source/spec sheet edition |
| Travel speed, reverse | approx. 12-13 km/h (7.5-8.1 mph) |
| Transmission/gear range | 7-speed planetary powershift, forward speed range approx. 10-66 km/h (6.2-41 mph) across gears |
| Gradeability | Not published in available spec sheets for this model |
Service capacities (summary)
| Fuel tank | 700 L (185 gal) |
| Engine oil (refill, with filter) | 76 L (20.1 gal) |
| Cooling system | approx. 137-151 L (36-40 gal); varies by source |
| Brake/hoist hydraulic tank | approx. 133 L (35 gal); total circuit volume including lines and cylinders cited up to approx. 393 L (103.9 gal) in some fluid-capacity references |
| Steering system | approx. 55-81 L (14.6-21.4 gal), tank vs. total-circuit figures differ by reference |
| Differential/final drives | approx. 140 L (37 gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
773D fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (incl. oil filter) - Cat 3412E TA/HEUI direct-injection V12 diesel | 76.1 L (20.1 US gal) | Cat DEO (Diesel Engine Oil). Standard/warm ambient: SAE 15W-40. Cold-start/low-ambient climates: SAE 10W-30. Multigrade selected by expected ambient temperature range, not a fixed single grade. |
| Cooling system | 151.0 L (39.9 US gal) | Cat ELC (Extended Life Coolant), factory premix (glycol/water) rated to roughly -37 deg C (-34 deg F) freeze protection. Do not mix ELC with conventional coolant or supplemental additive packages not rated for ELC service. |
| Fuel tank | 700.2 L (185.0 US gal) | Ultra-low-sulfur diesel fuel per Cat fuel spec, No. 2-D grade in normal conditions; switch to No. 1-D or a winter-blend diesel in cold ambient to prevent fuel gelling/wax. |
| Torque converter / transmission (includes gearbox sump) | 100.3 L (26.5 US gal) | Cat TDTO (TO-4 Transmission and Drive Train Oil). Graded by ambient temperature: SAE 10W for cold climates, SAE 30 for moderate ambient, SAE 50 for sustained hot/high-load operation. |
| Differential and final drives (rear axle, combined total - not split per side in published spec data) | approx. 140 L (37 US gal) - varies by configuration/series, confirm against machine-specific service data | Cat TDTO (TO-4), same drivetrain oil family and climate-based viscosity grading as the transmission (10W/30/50 by ambient). |
| Steering system, total (includes steering tank, lines, and cylinders) | 81.0 L (21.4 US gal) | Cat TDTO (TO-4) - the steering, brake, hoist, and torque-converter charge circuits share one drivetrain-oil family on this truck rather than a separate implement hydraulic oil. Viscosity graded by ambient as above. |
| Steering tank (reservoir only) | 55.3 L (14.6 US gal) | Cat TDTO (TO-4), same grade selection as steering system total. |
| Brake and hoist hydraulic system, total (includes hydraulic tank, coolers, and cylinders) | 393.3 L (103.9 US gal) | Cat TDTO (TO-4). Rear service brakes are oil-cooled multiple-disc units, so the friction-modified drivetrain oil (not a standard hydraulic oil) is specified for this circuit. Graded by ambient temperature. |
| Torque converter / brake / hoist hydraulic tank (shared reservoir) | 220.3 L (58.2 US gal) | Cat TDTO (TO-4), same grade selection as the brake/hoist system total. |
| Grease (chassis and pin/bushing lube points) | N/A - service item, no reservoir capacity | Cat Multipurpose Grease, NLGI 2, for general chassis fittings. Cat Advanced 3Moly Grease (NLGI 2, moly-fortified) for high-load pin and bushing joints such as hoist-cylinder and linkage pins. Typical service range roughly -30 deg C to +40 deg C (-22 deg F to +104 deg F). |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 773D maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
| Every 6,000 h |
|
Servicing the 773D beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S.O.S sampling on every fluid loop before defaulting to fixed change intervals. The 773D's shared TDTO circuit means one draw from the transmission, wet brakes, final drives or hydraulic tank flags contamination across the whole system. Track the 3412E's HEUI engine oil for soot loading and injector actuation wear, and pull coolant samples to confirm corrosion inhibitor level rather than guessing. Trend results over several samples — a single reading rarely tells the full story on a high-hour mining truck.
Corrective & Common Repairs
Loose or bouncy steering on the 773D usually traces to front strut kingpin bushing wear, since the front suspension cylinder doubles as the steering kingpin rather than a separate pin. Check nitrogen-over-oil strut charge if the ride goes hard or bottoms out. HEUI injector faults on the 3412E show up as rough idle or power loss before hard failure — pull codes early. Electronic transmission control faults often present as harsh or delayed shifts; check wiring and solenoids before condemning the valve body.
Overhaul & Rebuild Points
Box-section frame rails take the punishment on a 773D run hard in quarry service — inspect hoist-mount and hitch areas for fatigue cracking at every major service. Wheel-group planetary final drives and the torque converter/clutch-pack transmission are the big-ticket rebuilds on a high-hour unit; let TDTO sample trends set the timeline rather than a fixed hour number. Wet brake disc packs wear gradually under the oil-cooled design — replace by wear indicator, not calendar. Reseal hoist cylinders when rod seals start weeping.
Seasonal & Environment Servicing
Cold-start the 3412E with the ether or glow-plug aid below freezing and confirm coolant freeze protection before winter — a low-charge suspension strut also stiffens badly in cold weather. In hot, dusty quarry or surface-mine dirt, shorten air filter and aftercooler core cleaning frequency well below the indicator-triggered norm, since airborne fines load the cooling package fast. Wet-site or coastal operations need closer watch on TDTO water content, since the shared fluid loop spreads any contamination across brakes, transmission and final drives at once.
773D common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1R-0749 | Filter-Fuel | Fuel system service | Check fitment → |
| 129-0372 | Filter As-Water Sep & Fuel | Fuel system service | Check fitment → |
| 114-5988 | Film | Fuel system service | Check fitment → |
| 6I-2505 | Filter Element As-Air | Air intake service | Check fitment → |
| 6I-2506 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
773D fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| 164-3 | Injector Actuation Pressure Sensor circuit voltage above normal range. | Open circuit or short to supply in the injector actuation pressure (IAP) sensor wiring, or a failed sensor. | Inspect the IAP sensor connector and harness for damage or corrosion. Confirm sensor supply voltage and signal return before replacing the sensor. |
| 164-2 | Injector Actuation Pressure signal erratic, intermittent, or out of expected range. | Worn or failing injector actuation pressure control valve (IAPCV) on the HEUI pump, or injector O-ring wear letting actuation oil bypass at the cylinder head. | Check IAPCV coil resistance against spec, inspect for actuation-oil leakage around the injector bores, and confirm HEUI pump condition before replacing the sensor. |
| 110-3 | Engine Coolant Temperature Sensor circuit voltage above normal range. | Open circuit or short to supply in the coolant temperature sensor wiring, or a failed sensor. | Check the sensor connector and wiring for corrosion or damage, then verify sensor resistance against the temperature/resistance chart before replacing it. |
| 100-1 | Engine Oil Pressure reading valid but below normal operating range. | Low engine oil level, worn oil pump, plugged oil filter, or a failing oil pressure sensor. | Check oil level and condition first. Confirm actual pressure with a mechanical gauge before condemning the sensor or pump. |
| 190-12 | Primary engine speed/timing sensor signal lost. | Failed or disconnected primary speed/timing sensor, broken wiring to the ECM, or a damaged flywheel timing ring. | Check sensor air gap and connector, verify wiring continuity to the ECM, and confirm sensor supply voltage. The engine will not start if both primary and secondary signals are lost together. |
| 64-12 | Secondary engine speed/timing sensor signal lost. | Same failure modes as the primary sensor circuit: failed sensor, damaged wiring, or timing ring damage on the secondary channel. | Inspect and test the secondary sensor circuit the same way as the primary. Replace the sensor only after wiring and connectors check good. |
| 94-3 | Fuel Delivery (injection) Pressure Sensor circuit voltage above normal, open circuit. | Open circuit or short to supply in the fuel pressure sensor wiring, or a failed sensor. | Inspect the sensor connector and harness, confirm supply voltage at the sensor, and replace the sensor only if the circuit tests good. |
| 1-5 (applies per cylinder, e.g. 2-5, 3-5...) | Injector solenoid current below normal / open circuit on the numbered cylinder. | Open injector solenoid winding, broken or corroded harness connector at that injector, or a failed injector. | Check the injector connector and wiring for that cylinder, measure solenoid resistance, and swap with a known-good injector to isolate a wiring fault from an injector fault. |
| 826 | Torque converter (output) oil temperature reading abnormal or above normal range. | Low transmission/torque converter oil level, a restricted or fouled oil cooler, or a failing temperature sensor. | Check TDTO fluid level and cooler airflow/cleanliness first. Verify actual temperature with a separate gauge before replacing the sensor. |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
773D attachments & work tools
Dump body types
Body choices for this truck class run Flat Floor (for metering material and even crusher feed), Quarry, and Dual Slope (steep haul profiles, high-volume/coal-type loads with strong retention and a lower center of gravity). Bodies are offered lined or unlined, with a heat-treated, high-yield base and side plate for impact and abrasion resistance.
Body liners
Steel liner packages cover most quarry and aggregate duty; rubber liners are offered for extreme abrasion or noise-sensitive applications. Liner zones (base vs. sides) can be configured independently to balance payload against wear life for the material being hauled.
Body mounting / hoist arrangement
The body is not a quick-attach work tool; it is pinned to the frame at the rear hinge and raised by hydraulic hoist cylinder(s) actuated from an electro-hydraulic hoist lever in the cab. Tailgate fitment (open vs. gated) is selected per material flow characteristics rather than swapped as a field attachment.
Tires
Bias-ply or radial tires are offered across multiple tread patterns and manufacturers, sized in the 21.00-35 class shared with adjacent trucks in this size range (773B through 773G). Compound/tread selection is matched to haul-road and quarry underfoot conditions rather than a single fixed spec.
Traction control
A Traction Control System uses normal differential action to split torque between wheels in poor underfoot conditions, reducing stress on final drives and axles versus locking the differential outright. It works alongside the truck's electronic brake/production-monitoring package for traction assist during launch and grade work.
Payload/production monitoring
A VIMS-based production management package provides on-board payload weighing plus haul-cycle time and distance reporting, storing a large log of cycles for fleet management. This is a factory electronic option tied to the body/suspension load cells rather than a physical work tool.
Braking/retarder option
A retarder arrangement is offered as a configurable option for sustained grade control on long descents, used together with the standard oil-cooled multiple-disc service brakes. Selection typically pairs with the heated-body option in colder or wet-haul-road applications.
Cab guarding
The cab is a 4-point-mounted ROPS/FOPS structure meeting ISO rollover and falling-object protection criteria, standard rather than a bolt-on guard. Heater/air conditioning and powered windows are configurable cab comfort options.
Auxiliary site conversions
Water-tank/water-wagon conversions (tank, pump, and spray-bar) are commonly fitted to this truck's chassis for dust-suppression duty as a secondary-life or dealer-arranged build rather than a standard catalog work tool. These share the running gear and frame of the D/E/F-series platform footprint.
All 773D assemblies by section
Every catalogued assembly group for the Caterpillar 773D. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
6i-2588 Air Cleaner Gp -Lh
| 10***50 | Film; (Air Cleaner) (Radial Seal) (On Air Cleaner Cover) | 1 |
| 6I***05 | Filter Element As-Air; -Primary | 1 |
| 6I***06 | Filter Element As-Air; -Secondary | 1 |
7c-4782 Air Cleaner Gp
| 10***66 | Gasket | 2 |
| 15***14 | Precleaner Group; -Air Cleaner | 2 |
| 6I***86 | Air Cleaner Group; -Rh | 1 |
6i-2586 Air Cleaner Gp -Rh
| 10***50 | Film; (Air Cleaner) (Radial Seal) (On Air Cleaner Cover) | 1 |
| 6I***05 | Filter Element As-Air; -Primary | 1 |
| 6I***06 | Filter Element As-Air; -Secondary | 1 |
101-3431 Valve & Mtg Gp-Solenoid -Exhaust Bypass
| 10***30 | Valve Group-Solenoid; (Exhaust Bypass) | 1 |
| 10***31 | Valve & Mounting Group; -Exhaust Flow-Engine Speed | 1 |
| 3E***10 | Manifold | 1 |
189-8665 Valve Gp-Solenoid
| 10***55 | Cartridge As | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
101-3430 Valve Gp-Solenoid
| 10***30 | Valve Group-Solenoid; (Exhaust Bypass) | 1 |
| 10***55 | Cartridge As | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
129-6836 Aftercooler Gp-Water
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 20 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 2 |
103-4052 Cartridge Gp-Turbocharger
| 10***52 | Cartridge Group-Turbocharger | 1 |
| 10***25 | Nut; (3/8-24-Thd) | 1 |
| 13***17 | Shaft As-Turbine | 1 |
119-1273 Control Gp-Exhaust Flow
| 00***33 | Tee-Pipe | 1 |
| 00***10 | Tee; (Pipe) | 1 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 1 |
167-9658 Exhaust Ar-Engine -Diverter
| 11***73 | Control Group-Exhaust Flow; -Diverter | 1 |
| 15***53 | Muffler Group; -Engine | 1 |
| 16***58 | Exhaust Ar-Engine; -Diverter | 1 |
136-3178 Exhaust Ar-Engine
| 13***78 | Exhaust Ar-Engine | 1 |
| 15***41 | Pipe Group-Exhaust | 1 |
| 15***53 | Muffler Group; -Engine | 1 |
127-6259 Lines Gp-Air -Turbocharger Inlet
| 12***71 | Tube | 1 |
| 12***59 | Elbow | 1 |
| 12***59 | Lines Group-Air; -Turbocharger Inlet | 1 |
160-7608 Lines Gp-Air -Turbocharger Inlet
| 10***68 | Plate As | 4 |
| 10***01 | Manifold As | 1 |
| 16***08 | Lines Group-Air; -Turbocharger Inlet | 1 |
142-4035 Lines Gp-Air -Turbocharger Exhaust
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 4 |
| 12***08 | Elbow-Exhaust | 1 |
| 14***35 | Lines Group-Air; -Turbocharger Exhaust | 1 |
143-0055 Lines Gp-Air -Turbocharger Inlet
| 12***42 | Tube As | 1 |
| 12***71 | Tube | 1 |
| 14***55 | Lines Group-Air; -Turbocharger Inlet | 1 |
129-6832 Lines Gp-Air -Turbocharger Inlet
| 11***23 | Tube As-Turbocharger; (Lh) | 1 |
| 11***35 | Pipe-Turbocharger Outlet | 1 |
| 12***32 | Lines Group-Air; -Turbocharger Inlet | 1 |
129-6834 Manifold Gp-Exhaust
| 10***06 | Manifold-Exhaust; (End) | 4 |
| 10***12 | Spacer; (11.13x19.05x53-mm Thk) | 20 |
| 11***48 | Manifold-Exhaust; (Center, Rh) | 1 |
164-4603 Manifold Gp-Exhaust
| 10***12 | Spacer; (11.13x19.05x53-mm Thk) | 20 |
| 11***23 | Spacer; (11.13x19.05x19-mm Thk) | 4 |
| 12***52 | Gasket-Exhaust Manifold | 12 |
159-7353 Muffler Gp
| 03***09 | Locknut; (3/8-16-Thd) | 8 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 8 |
| 15***53 | Muffler Group; -Engine | 1 |
159-7341 Pipe Gp-Exhaust
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 9 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 15***35 | Box As | 1 |
142-5676 Pipe Gp-Exhaust
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 6 |
| 14***76 | Pipe Group-Exhaust | 1 |
169-0429 Pipe Gp-Exhaust -Diverter
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 15 |
| 0S***75 | Pin-To Arm Assembly And Retainer | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
4w-7263 Precleaner Gp -Air
| 1N***03 | Bolt-Hex Head | 1 |
| 2S***93 | Precleaner Cover Assembly | 1 |
| 2S***08 | Collector-Dust; (Air Precleaner) | 1 |
150-1714 Precleaner Gp -Air Cleaner
| 15***14 | Precleaner Group; -Air Cleaner | 1 |
| 2S***93 | Precleaner Cover Assembly | 1 |
| 2S***08 | Collector-Dust; (Air Precleaner) | 1 |
116-4120 Turbocharger Gp
| 10***52 | Cartridge Group-Turbocharger | 1 |
| 10***98 | Housing (Turbin) | 1 |
| 11***20 | Turbocharger Group | 1 |
129-6835 Turbocharger Gp
| 11***20 | Turbocharger Group | 2 |
| 12***35 | Turbocharger Group | 1 |
| 1S***95 | Gasket-Turbocharger To Manifold; Gasket Turbocharger To Manifold | 2 |
217-7903 Valve & Mtg Gp-Solenoid
| 18***65 | Valve Group-Solenoid; -Exhaust Bypass | 1 |
| 21***03 | Valve & Mtg Group-Solenoid; -Exhaust Bypass | 1 |
| 3E***10 | Manifold | 1 |
6d-1039 Valve Gp-Air Control -Exhaust Diverter
| 3P***59 | Spring | 1 |
| 6D***39 | Valve As; -Exhaust Bypass-Exhaust Diverter | 1 |
| 6F***72 | Seal (.674" Inside Diameter) | 1 |
Basic Engine
4n-6842 Air Compressor Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 5 |
| 12***48 | Seal-Integral | 1 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 3 |
4n-7378 Air Compressor Gp
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 6 |
| 11***37 | Kit-Piston Ring; (Compressor 5 Ring) | 1 |
| 1W***03 | Plug | 2 |
125-5072 Belt Tensioner Gp
| 0S***75 | Pin-To Arm Assembly And Retainer | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 12***71 | Spring | 1 |
108-1553 Camshaft Gp
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 10***74 | Gear-Camshaft Drive; (86-Teeth) | 1 |
| 10***53 | Camshaft Group | 1 |
168-8911 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 10 |
| 16***11 | Cover Group-Cylinder Block | 1 |
| 23***37 | Seal-Integral | 1 |
129-5229 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 13 |
| 12***29 | Cover Group-Cylinder Block | 1 |
| 23***37 | Seal-Integral | 1 |
131-2002 Cover Gp-Flywheel Housing
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 3 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
126-0768 Cover Gp-Front Housing
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 3 |
| 11***21 | Support-Housing; (Rh) | 1 |
129-6830 Cover Gp-Oil Pan -Engine
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 10***39 | Plug-Drain; (Engine Oil Pan) | 1 |
138-6642 Cover Gp-Valve Mechanism
| 10***88 | Base-Valve Mechanism Cover | 6 |
| 11***84 | Cover-Valve Mechanism | 2 |
| 11***15 | Cover As-Valve | 4 |
4n-0922 Crankshaft Gp
| 14***67 | Seal Group-Crankshaft; (Front) | 1 |
| 14***68 | Seal-Crankshaft; (Rear)(Flywheel Housing) | 1 |
| 15***40 | Gear-Crankshaft; (99-Teeth) | 1 |
117-9512 Cylinder Block As
| 11***20 | Seal-O-Ring; (Mid-Liner) | 12 |
| 11***12 | Cylinder Block As | 1 |
| 14***17 | Seal-O-Ring; (140.20mm Id) | 12 |
126-1372 Cylinder Block As
| 12***72 | Cylinder Block As | 1 |
| 2W***15 | Insert-Liner Seat; (1.605-mm Thk)(1.59mm Thk) | 0 |
| 3P***23 | Bolt-Bearing Cap; (7/8-14x7.75-In) | 14 |
109-9010 Cylinder Block Gp
| 10***23 | Insert-Liner Seat; (5.21-mm Thk)(5.21mm Thk) | 0 |
| 10***24 | . Cover, Insert-Liner Seat; (5.16-mm Thk)(0.5-mm Us) | 0 |
| 10***25 | Insert-Liner Seat; (5.26-mm Thk)(0.5-mm Os), . Cover | 0 |
126-1373 Cylinder Block Gp
| 11***27 | Seal-O-Ring; (19.18mm Id) | 8 |
| 12***72 | Cylinder Block As | 1 |
| 12***73 | Cylinder Block Group | 1 |
7w-2243 Cylinder Head As
| 14***46 | Cylinder Head As | 1 |
| 17***88 | Guide-Valve; (Standard) | 24 |
| 2N***75 | Dowel | 12 |
105-3800 Cylinder Head As
| 10***00 | Cylinder Head As | 1 |
| 1W***83 | Insert-Valve Seat; (Exhaust)(Standard) | 12 |
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 12 |
143-0046 Cylinder Head As
| 14***46 | Cylinder Head As | 1 |
| 1W***83 | Insert-Valve Seat; (Exhaust)(Standard) | 12 |
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 12 |
143-0047 Cylinder Head As
| 14***46 | Cylinder Head As | 1 |
| 14***47 | Cylinder Head As | 1 |
| 17***88 | Guide-Valve; (Standard) | 24 |
192-1322 Cylinder Head As
| 10***94 | Dowel | 2 |
| 14***46 | Cylinder Head As | 1 |
| 17***88 | Guide-Valve; (Standard) | 24 |
108-1887 Cylinder Head Gp
| 10***94 | Dowel | 2 |
| 10***00 | Cylinder Head As | 1 |
| 10***87 | Cylinder Head Group | 1 |
108-1552 Cylinder Head Gp
| 03***27 | Seal-O-Ring; (19.18mm Id) | 2 |
| 06***61 | Seal-O-Ring (Id=40.87mm) | 12 |
| 10***92 | Stud-Taperlock; (3/8-16x3.93in) | 24 |
6n-2229 Damper Gp
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 12 |
| 16***30 | Damper As | 1 |
| 2D***74 | Bolt; (5/8-18x6.75-In) | 8 |
9n-0725 Drive Gp-Accessory
| 5P***40 | Seal-O-Ring | 1 |
| 6B***83 | Nut,Plain,Hexagon Lever | 1 |
| 7N***22 | Gear-Compressor Drive; (46-Teeth) | 1 |
125-5065 Drive Gp-Fan
| 12***62 | Bracket As-Fan | 1 |
| 12***65 | Drive Group-Fan | 1 |
| 1S***09 | Shaft-Tightener | 1 |
4n-7734 Flywheel Gp
| 2D***74 | Bolt; (5/8-18x6.75-In) | 12 |
| 4D***04 | Washer,Flat Cover Mtg,Accessory Drive | 12 |
| 4N***14 | Gear; (113-Teeth)(Flywheel Starter) | 1 |
188-4500 Gear Gp-Front -Timing
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 10***13 | Plate-Retaining | 1 |
| 10***16 | Gear; (85-Teeth)(Oil Pump) | 1 |
126-7282 Gear Gp-Front -Timing
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 10***13 | Plate-Retaining | 1 |
| 10***16 | Gear; (85-Teeth)(Oil Pump) | 1 |
4n-3825 Gear Gp-Rear
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 4 |
| 4N***25 | Gear Group-Rear; Rear Timing Gear Group | 1 |
| 4W***85 | Gear-Camshaft; (86-Teeth) | 1 |
136-7907 Gear Gp-Rear -Pump Drive Lubrication
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 13***36 | Adapter | 1 |
| 13***37 | Gear; (56 Teeth) | 1 |
129-6829 Housing Gp-Flywheel
| 03***94 | Connector-Flared | 1 |
| 03***68 | Elbow (For Use With Shallow Pan) | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
137-8142 Housing Gp-Front
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 3 |
| 12***28 | Sensor Group-Speed; -Engine Speed/Timing | 2 |
| 13***42 | Housing Group-Front | 1 |
126-7280 Housing Gp-Front
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 2 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 3 |
| 12***80 | Housing Group-Front | 1 |
129-5255 Lifting Gp-Engine
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
122-0939 Lifting Gp-Engine -Side
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 11***75 | Bracket-Lifting; (Right) | 1 |
| 11***15 | Bracket-Lifting; (Left) | 1 |
129-6838 Lines Gp-Air Compressor
| 00***43 | Elbow; (12.7mm Id) | 1 |
| 00***26 | Connector; (Flared)(3/4-16 Thd, 47 mm Long) | 1 |
| 03***49 | Elbow; (90 Degree, 37 Degree Flared) | 1 |
132-3627 Pan Gp-Oil -Engine
| 13***27 | Pan Group-Oil; -Engine | 1 |
| 2P***03 | Bolt-Washer Head; (3/8-16x1.25-In) | 38 |
| 6N***96 | Gasket-Oil Pan | 1 |
109-2823 Piston & Rod Gp
| 10***23 | Piston & Rod Group | 1 |
| 13***61 | Ring-Piston; (Top)(Top) | 1 |
| 15***56 | Bolt-Special; (Oil Jet) | 1 |
192-8808 Piston & Rod Gp
| 13***61 | Ring-Piston; (Top)(Top) | 1 |
| 15***56 | Bolt-Special; (Oil Jet) | 1 |
| 16***78 | Rod As-Connecting | 1 |
128-5513 Platform Gp-Engine
| 12***13 | Platform Group-Engine | 1 |
| 13***26 | Platform As | 1 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 2 |
129-5228 Plug Gp-Cylinder Block
| 12***28 | Plug Group-Cylinder Block | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 4 |
| 7W***34 | Plug-Pipe (3/8-18 Nptf Thd) | 4 |
129-6827 Plug Gp-Cylinder Head
| 12***27 | Plug Group-Cylinder Head | 1 |
| 4N***32 | Plug-Cup | 2 |
| 5P***63 | Plug-Cup | 2 |
8n-3448 Pulley Gp-Fan Drive
| 6N***59 | Pulley-Crankshaft; (2-Groove) | 1 |
| 8N***29 | Pulley-Crankshaft; (3-Groove) | 1 |
| 8N***48 | Pulley Group-Fan Drive | 1 |
107-1954 Rocker Arm Gp
| 10***54 | Rocker Arm Group | 1 |
| 10***03 | Screw; (3/8-24x1.67-In)(Intake) | 2 |
| 12***63 | Bracket-Shaft | 1 |
7e-6385 Support Gp-Engine -Front
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 4 |
| 4D***04 | Washer,Flat Cover Mtg,Accessory Drive | 4 |
| 4N***84 | Support-Front Engine | 1 |
142-4031 Support Gp-Engine -Rear
| 14***31 | Support Group-Engine; -Rear | 1 |
| 2A***38 | Bolt-(3/4" X 2-1/4")-Rops Mounting Bracket To Fender | 12 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 12 |
125-5041 Support Gp-Engine -Chassis
| 12***41 | Support Group-Engine; -Chassis | 1 |
| 1D***09 | Bolt Canopy Assembly To Mounting Brackets; Bolt-Canopy Assembly To Mounting Brackets | 4 |
| 1D***14 | Bolt--Front Support To Frame | 4 |
129-6828 Trunnion Gp-Engine
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 4 |
| 12***28 | Trunnion Group-Engine | 1 |
| 34***37 | Mount As; (Resilient) | 1 |
108-1874 Valve Mechanism Gp
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 12 |
| 10***89 | Bridge-Valve | 24 |
| 10***88 | Valve Lifter Assem | 24 |
Braking System
2g-6535 Slack Adjuster Gp -Rear
| 2G***02 | Spring | 2 |
| 2G***35 | Slack Adjuster Group; -Front Service Brake Lines | 1 |
| 2G***82 | Base | 1 |
131-3752 Air Dryer Gp
| 11***35 | Valve-Check | 1 |
| 12***51 | Ring | 1 |
| 13***52 | Air Dryer Group; -Brake | 1 |
105-3210 Brake Gp-Service -Front Caliper
| 10***09 | Plate | 2 |
| 10***07 | Disc | 2 |
| 10***10 | Brake Group; -Front Caliper | 1 |
125-1384 Brake Gp-Hyd Caliper Service -Front
| 11***97 | Lining As-Brake; (Outboard) | 1 |
| 11***99 | Lining As-Brake; (Inboard) | 1 |
| 11***03 | Cover | 1 |
2a-7070 Brake Gp-Service & Parking
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 16 |
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 70 |
| 10***08 | Anchor-Brake | 2 |
137-6428 Control Ar-Integrated Brake
| 13***28 | Control Ar-Integrated Brake | 1 |
| 13***25 | Control Group-Retarder; -Chassis | 1 |
| 14***03 | Lines Group-Traction Aid | 1 |
157-2714 Control Gp-Parking Brake -Cab
| 12***98 | Film-Instruction; (Parking Brake) | 1 |
| 12***71 | Valve Group-Air Control | 1 |
| 14***01 | Lever; (Parking Brake) | 1 |
136-1815 Control Gp-Service Brake -Platform
| 00***54 | Nipple-Pipe | 1 |
| 10***08 | Hose As | 1 |
| 13***15 | Control Group-Service Brake; -Platform | 1 |
188-3968 Control Gp-Service Brake -Platform
| 00***54 | Nipple-Pipe | 1 |
| 14***39 | Kit-Seal & Valve; (Brake Air Relay)(Master Cylinder Relay Valve) | 1 |
| 15***49 | Valve Group-Relay; (Brake Air)(Auto Retarder Cont) | 2 |
163-5421 Control Gp-Service Brake -Cab
| 00***99 | Tee To Bushing | 1 |
| 00***33 | Tee-Pipe | 1 |
| 12***01 | Film-Information; (Indicator Lights) | 1 |
159-5294 Control Gp-Service Brake -Chassis
| 15***94 | Control Group-Service Brake; -Chassis | 1 |
| 1S***96 | Clip (2.25" Long) | 1 |
| 2G***22 | Hose Assem. 111.76cm (44 In.) | 1 |
8w-3405 Cylinder Gp-Air/Hydraulic -Rear Brake
| 13***31 | Seal | 1 |
| 25***38 | Valve | 1 |
| 2F***16 | Nut (Mounted On Flywheel Housing) | 8 |
8x-6987 Cylinder Gp-Air/Hydraulic -Front Brake
| 2F***16 | Nut (Mounted On Flywheel Housing) | 8 |
| 5T***48 | Kit-Air Cylinder; (Incl Rings,Seals,Cup, | 1 |
| 6W***06 | Spring | 1 |
132-5448 Filter Gp-Oil -Parking Brake Release
| 10***36 | Seal-O-Ring; (49.28mm Id) | 2 |
| 12***14 | Filter-Oil; (Ultra High Efficiency) | 2 |
| 13***12 | Filter-Oil; (Advanced Efficiency) | 2 |
188-3970 Lines Gp-Service Brake -Platform
| 10***36 | Clip | 2 |
| 14***26 | Tank Group-Brake | 1 |
| 14***22 | Adapter; (-10orb/-12orfs) | 1 |
135-9414 Lines Gp-Service Brake -Rear
| 10***36 | Clip | 9 |
| 11***43 | Valve Group-Brake; -Automatic Retarder-Park, Secondary Brake | 1 |
| 13***48 | Filter Group-Oil; -Parking Brake Release | 1 |
135-9415 Lines Gp-Service Brake -Front
| 11***94 | Hose As | 2 |
| 13***15 | Lines Group-Service Brake; -Front | 1 |
| 14***23 | Hose As | 1 |
159-5292 Lines Gp-Service Brake -Platform
| 10***36 | Clip | 2 |
| 13***52 | Tube As | 1 |
| 13***54 | Tube As | 1 |
139-5224 Retarder Ar-Automatic
| 13***24 | Retarder Ar-Automatic | 1 |
| 13***25 | Control Group-Retarder; -Chassis | 1 |
| 17***50 | Cab Ar; -Automatic Retarder Control | 1 |
159-3057 Tank Gp-Air -Secondary
| 14***46 | Plug-Pipe | 1 |
| 15***57 | Tank Group-Air; -Secondary | 1 |
| 16***80 | Tank-Air | 1 |
188-3966 Tank Gp-Air -Primary
| 18***83 | Tank As-Air | 1 |
| 18***66 | Tank Group-Air; -Primary | 1 |
| 2H***91 | Union --Block To Hose Assembly; -- Block To Hose Assembly | 2 |
131-3755 Tank Gp-Air -Primary
| 03***77 | Tee-Pipe | 2 |
| 13***55 | Tank Group-Air; -Primary | 1 |
| 16***30 | Tank-Air | 2 |
143-9426 Tank Gp-Brake
| 14***26 | Tank Group-Brake | 1 |
| 2S***78 | Seal-O-Ring (Id=37.47mm) | 1 |
| 5J***06 | Fitting; (9/16-18-Thd) | 1 |
217-7906 Valve & Mtg Gp-Brake
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***63 | Switch As-Pressure; (Tractor Brake) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
127-4661 Valve & Mtg Gp-Brake -Automatic Retarder
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***63 | Switch As-Pressure; (Tractor Brake) | 1 |
| 12***61 | Valve & Mtg Group-Brake; -Automatic Retarder | 1 |
113-1543 Valve Gp-Brake -Parking, Secondary
| 03***60 | Bolt-Self Locking; (5/16-18x1.0) | 2 |
| 11***43 | Valve Group-Brake; -Automatic Retarder-Park, Secondary Brake | 1 |
| 11***24 | Cylinder Group-Air; (Brake) | 1 |
9v-1541 Valve Gp-Check -Front Brake
| 2R***32 | Guide-Shuttle | 1 |
| 2R***14 | Cap | 1 |
| 3D***45 | Seal-Bottle To Connector | 1 |
6d-3781 Valve Gp-Check -Retarder Control-Service Brake Control
| 2R***32 | Guide-Shuttle | 1 |
| 2R***13 | Cap | 1 |
| 3D***45 | Seal-Bottle To Connector | 1 |
179-9935 Valve Gp-Check -Parking, Secondary Brake
| 13***33 | Valve-Check; (Parking & Secondary Brake) | 1 |
| 17***35 | Valve Group-Check; -Parking, Secondary Brake | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
1u-2644 Valve Gp-Check -Parking, Secondary Brake
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 1U***44 | Valve Group-Check; -Secondary, Parking Brake | 1 |
| 21***68 | Seal-O-Ring; (11.89-mm Id) | 1 |
4k-9714 Valve Gp-Check -Front Brake
| 4K***14 | Valve Group-Check; -Brake Air Relay | 1 |
| 9V***76 | Valve Group-Check; Check Valve Group-Wagner Electric Corp | 1 |
| 9V***41 | Valve Group-Check; -Brake Air Relay | 1 |
9v-0476 Valve Gp-Check -Front Brake
| 5K***63 | Gasket | 1 |
| 5K***65 | Retainer & Seat Assem. | 1 |
| 9V***76 | Valve Group-Check; Check Valve Group-Wagner Electric Corp | 1 |
3g-2887 Valve Gp-Diverter -Towing, Parking Brake Release
| 3G***87 | Valve Group-Diverter; -Towing, Parking Brake Release | 1 |
| 8D***55 | Seal-Quad Ring | 2 |
| 8D***56 | Ring-Retaining | 2 |
6e-6305 Valve Gp-Relief -Parking, Secondary Brake
| 06***39 | Seal-O-Ring | 1 |
| 3G***26 | Nut; (3/8-40-Thd) | 1 |
| 3G***54 | Cap | 1 |
3e-8691 Valve Gp-Solenoid
| 10***17 | Cartridge As | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
7t-9074 Valve Gp-Solenoid
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
189-8666 Valve Gp-Solenoid
| 10***17 | Cartridge As | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
185-0008 Valve Gp-Solenoid
| 15***70 | Nut; (1/2-20-2b-Thd) | 1 |
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 18***08 | Valve Group-Solenoid; -Air Horn | 1 |
188-9250 Valve Gp-Solenoid
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 18***50 | Valve Group-Solenoid | 1 |
Cooling System
141-4109 Core Gp-Oil Cooler -Brake, Hoist
| 14***09 | Core Group-Oil Cooler; -Brake, Frame Mount-Transmission, Engine Mount-Tc, Bk, Hoist, Engine Mount | 1 |
| 8T***64 | Plug-Pipe; (1/8-27-Thd)(Cylinder Head) | 2 |
125-5070 Fan Gp-Suction
| 12***67 | Guard As-Fan; (Rh) | 1 |
| 12***68 | Guard As-Fan; (Lh) | 1 |
| 12***70 | Fan Group-Suction | 1 |
143-0057 Lines Gp-Coolant Drain
| 14***93 | Hose As | 1 |
| 14***94 | Hose As | 1 |
| 14***57 | Lines Group-Coolant Drain | 1 |
134-2828 Lines Gp-Water
| 01***24 | Bushing To Supply Port | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 4 |
131-3347 Lines Gp-Water -Aftercooler
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 3 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 3 |
4n-5837 Pump Gp-Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***49 | Adapter-Inlet | 1 |
| 11***79 | Seal-O-Ring | 1 |
137-1339 Pump Gp-Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***30 | Bearing As-Roller | 1 |
| 11***21 | Plug-Felt; (Water Pump Housing) | 1 |
134-1487 Pump Gp-Water
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***85 | Retainer | 1 |
| 10***90 | Housing As-Pump | 1 |
203-7962 Radiator Gp
| 10***22 | Tube As-Inlet | 1 |
| 10***84 | Dial | 1 |
| 12***44 | Radiator Group | 1 |
125-5044 Radiator Gp
| 12***33 | Channel As | 1 |
| 12***34 | Channel As | 1 |
| 12***36 | Tank As-Radiator | 1 |
140-3653 Radiator Gp
| 10***22 | Tube As-Inlet | 1 |
| 12***44 | Radiator Group | 1 |
| 12***46 | Shield As | 1 |
Electrical And Starting System
123-6449 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***49 | Alarm Group | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
3e-6328 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 3E***28 | Alarm Group; -Caterpillar Monitoring System-Action | 1 |
169-3345 Alternator Gp-Charging
| 16***45 | Alternator Group-Charging | 1 |
| 18***38 | Collar | 2 |
| 18***39 | Fan As; (Alternator) | 1 |
4n-2185 Alternator Gp-Charging
| 0S***23 | Bolt (.50 In. Diameter) | 1 |
| 16***45 | Alternator Group-Charging | 1 |
| 1S***98 | Rod | 1 |
137-6424 Battery & Wiring Gp -Cold Weather
| 11***18 | Clip | 1 |
| 11***34 | Switch Group-Magnetic; -Start Relay | 1 |
| 13***24 | Battery & Wiring Group; -Cold Weather Starting | 1 |
159-5295 Battery & Wiring Gp
| 03***97 | Boot | 1 |
| 12***54 | Cable As; (Disconnect) | 1 |
| 15***57 | Cover | 1 |
131-2001 Control & Mtg Gp-Engine Elek
| 10***22 | Control Group-Engine Electronic | 1 |
| 11***69 | Spacer-Special; (8.2x25x89.7-mm Thk) | 4 |
| 13***01 | Control & Mtg Group-Engine Elek | 1 |
131-3763 Control & Mtg Gp-Power Train
| 11***42 | Insulator | 2 |
| 13***63 | Control & Mtg Group-Power Train; -Transmission, Chassis | 1 |
| 16***36 | Plate As | 1 |
142-7130 Control Gp-Eng Ratings Elek
| 14***30 | Control Group-Eng Ratings Elek | 1 |
| 3E***99 | Plate-Marking | 1 |
145-1034 Control Gp-Eng Ratings Elek
| 14***34 | Control Group-Eng Ratings Elek | 1 |
134-5578 Control Gp-Eng Ratings Elek
| 13***78 | Control Group-Eng Ratings Elek | 1 |
143-7928 Control Gp-Eng Ratings Elek
| 14***28 | Control Group-Eng Ratings Elek | 1 |
105-6122 Control Gp-Engine Electronic
| 10***22 | Control Group-Engine Electronic | 1 |
| 17***02 | Control Group-Engine Electronic | 1 |
156-7172 Control Gp-Engine Electronic
| 12***74 | Screw-Pan Head; (8-32x9.52-mm) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 15***72 | Control Group-Engine Electronic | 1 |
172-0802 Control Gp-Engine Electronic
| 11***11 | Cover | 1 |
| 12***74 | Screw-Pan Head; (8-32x9.52-mm) | 1 |
| 17***02 | Control Group-Engine Electronic | 1 |
172-9387 Control Gp-Unprogrammed -Traction Control-Transmission, Chassis-Integrated Brake
| 10***52 | Screw-Pan Head; (8-32x0.375-In) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 17***87 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Integrated Brake | 1 |
172-9391 Control Gp-Unprogrammed -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake
| 10***52 | Screw-Pan Head; (8-32x0.375-In) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 17***91 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake | 1 |
200-5374 Electronics Gp-Machine -Traction Control
| 17***87 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Integrated Brake | 1 |
| 20***74 | Electronics Group-Machine; -Traction Control | 1 |
| 29***94 | Software Group-Machine | 1 |
200-5372 Electronics Gp-Machine -Integrated Brake
| 14***94 | Film-Identification; (Integrated Brake Control) | 1 |
| 17***87 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Integrated Brake | 1 |
| 19***79 | Software Group-Machine; -Integrated Brake | 1 |
200-5373 Electronics Gp-Machine -Automatic Retarder
| 17***87 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Integrated Brake | 1 |
| 19***82 | Software Group-Machine; -Automatic Retarder | 1 |
| 20***73 | Electronics Group-Machine; -Automatic Retarder | 1 |
164-6900 Electronics Gp-Machine -Traction Control
| 14***93 | Film; (Traction Control) | 1 |
| 16***00 | Electronics Group-Machine; -Traction Control | 1 |
| 17***91 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake | 1 |
164-6898 Electronics Gp-Machine -Integrated Brake
| 14***94 | Film-Identification; (Integrated Brake Control) | 1 |
| 16***98 | Electronics Group-Machine; -Integrated Brake | 1 |
| 17***91 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake | 1 |
164-6899 Electronics Gp-Machine -Automatic Retarder
| 14***92 | Film-Identification; (Automatic Retarder)(Automatic Retarder) | 1 |
| 16***99 | Electronics Group-Machine; -Automatic Retarder | 1 |
| 17***91 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake | 1 |
164-6901 Electronics Gp-Power Train -Transmission/Chassis
| 14***91 | Film-Identification; (Transmission Control)(Transmission) | 1 |
| 16***01 | Electronics Group-Power Train; -Transmission/Chassis | 1 |
| 17***91 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Automatic Retarder-Integrated Brake | 1 |
200-5375 Electronics Gp-Power Train -Transmission, Chassis
| 14***91 | Film-Identification; (Transmission Control)(Transmission) | 1 |
| 17***87 | Control Group-Unprogrammed; -Traction Control-Transmission, Chassis-Integrated Brake | 1 |
| 20***75 | Electronics Group-Power Train; -Transmission, Chassis | 1 |
168-7059 Heater Gp-Jacket Water
| 16***85 | Plate As | 1 |
| 16***59 | Heater Group-Jacket Water | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 1 |
168-7060 Heater Gp-Jacket Water
| 16***85 | Plate As | 1 |
| 16***60 | Heater Group-Jacket Water | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 1 |
8c-9678 Lamp Gp-Dome
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***82 | Housing (Plug) (To Lift Kickout Switch) | 1 |
162-3294 Lamp Gp-Flood -Backup
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***52 | Bezel | 1 |
| 16***94 | Lamp Group-Flood; -Rear-Ladder Access-Engine Work Light | 1 |
157-0305 Lamp Gp-Head -High Beam
| 15***05 | Lamp Group-Head; -High Beam | 1 |
| 15***49 | Lens As; (Headlight, High Beam) | 1 |
| 15***50 | Body As-Lamp | 1 |
161-0908 Lamp Gp-Head
| 15***50 | Body As-Lamp | 1 |
| 15***52 | Bezel | 1 |
| 16***08 | Lamp Group-Head; -Fog Light | 1 |
161-4016 Lamp Gp-Rear
| 11***14 | Bracket Assem. | 1 |
| 13***26 | Lamp Group-Signal; (24-Volt, Stop, Tail)(Stop/Tail) | 1 |
| 13***27 | Lamp Group-Signal; -Park, Turn | 1 |
8t-9684 Lamp Gp-Signal
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***38 | Housing-Receptacle-Sure Seal-Assemble | 1 |
8t-9683 Lamp Gp-Signal
| 7D***14 | Kit (Lens) (Includes Gasket, Screw & Lens) | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
135-0427 Lamp Gp-Signal -Park, Turn
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***27 | Lamp Group-Signal; -Park, Turn | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
135-0426 Lamp Gp-Signal -Stop, Tail
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***26 | Lamp Group-Signal; (24-Volt, Stop, Tail)(Stop/Tail) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
177-0220 Panel Gp-Circuit Breaker
| 13***78 | Cap; (Fuse Holder) | 1 |
| 16***49 | Cover | 1 |
| 17***67 | Wire As | 1 |
161-9850 Panel Gp-Circuit Breaker
| 13***78 | Cap; (Fuse Holder) | 1 |
| 16***46 | Wire As | 1 |
| 16***47 | Harness As; (Circuit Breaker) | 1 |
113-0752 Sensor & Mtg Gp-Payload
| 03***67 | Ring; (Back Up) | 4 |
| 03***39 | Seal-O-Ring (Id=9.25mm) | 4 |
| 11***52 | Sensor & Mtg Group-Payload | 1 |
219-2389 Sensor Gp-Position
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 21***89 | Sensor Group-Position | 1 |
176-1602 Sensor Gp-Position -Accelerator Control
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 17***02 | Sensor Group-Position; -Accelerator Control | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
118-8471 Sensor Gp-Position
| 11***71 | Sensor Group-Position; -Transmission Gear | 1 |
| 7B***42 | Bolt, Hex. Hd., 1/4in.-20 N.C. X 1 1/4in. | 2 |
| 7T***76 | Spacer; (1.22-mm Thk) | 1 |
204-7949 Sensor Gp-Position
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 20***49 | Sensor Group-Position; -Throttle | 1 |
198-8761 Sensor Gp-Position
| 19***61 | Sensor Group-Position; (Transmission Speed) | 1 |
| 7B***42 | Bolt, Hex. Hd., 1/4in.-20 N.C. X 1 1/4in. | 2 |
| 7T***76 | Spacer; (1.22-mm Thk) | 1 |
3e-7700 Sensor Gp-Position -Accelerator Control
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 3E***00 | Sensor Group-Position; -Accelerator Control | 1 |
| 8T***29 | Pin-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
126-7896 Sensor Gp-Position
| 12***96 | Sensor Group-Position; -Transmission Shift Lever | 1 |
| 7T***76 | Spacer; (1.22-mm Thk) | 1 |
| 8T***28 | Seal-Lip Type | 1 |
137-7579 Sensor Gp-Position -Hoist Control
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***79 | Sensor Group-Position; -Hoist Control | 1 |
| 8T***29 | Pin-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
194-6722 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 19***22 | Sensor Group-Pressure; -Atmospheric Air | 1 |
153-3962 Sensor Gp-Pressure -Air System
| 15***62 | Sensor Group-Pressure; -Lockup Clutch | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
161-9926 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***26 | Sensor Group-Pressure; -Atmospheric Air, Turbo Inlet | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
194-6724 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 3 |
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
194-6725 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 19***25 | Sensor Group-Pressure; -Engine Oil | 1 |
103-6092 Sensor Gp-Pressure -Engine Oil
| 10***08 | Kit; (Connecting Plug) (3 Pin) (Includes Plug As And Wedge) | 1 |
| 10***13 | Seal; (3 Pin Plug) | 1 |
| 10***92 | Sensor Group-Pressure; -Filtered Oil, Unfiltered Oil | 1 |
124-0328 Sensor Gp-Pressure -Payload
| 12***28 | Sensor Group-Pressure; -Payload | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
161-9925 Sensor Gp-Pressure -Atmospheric Air
| 10***13 | Seal; (3 Pin Plug) | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***25 | Sensor Group-Pressure; -Turbocharger Inlet | 1 |
103-6093 Sensor Gp-Pressure -Atmospheric Air
| 10***93 | Sensor Group-Pressure; -Turbocharger Inlet-Atmospheric, Crankcase | 1 |
| 15***89 | Tube; (3cm) | 0 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
167-1709 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***09 | Sensor Group-Pressure; -Injection Actuation Oil | 1 |
| 9X***13 | Sleeve (Order By cm)(Use As Required) | 0 |
185-0600 Sensor Gp-Pressure
| 18***00 | Sensor Group-Pressure | 1 |
| 8T***30 | Socket-Connector; (16-Ga To 18-Ga)(Throttle Position Sensor) | 3 |
| 8T***31 | Plug-Connector; (3-Pin) | 1 |
175-3186 Sensor Gp-Pressure -Suspension Cylinder
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***86 | Sensor Group-Pressure; -Suspension Cylinder | 1 |
| 3E***68 | Wedge-Plug Lock; (3-Pin) | 1 |
161-9931 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***31 | Sensor Group-Pressure; -Atmospheric | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 3 |
5t-4118 Sensor Gp-Speed
| 1T***84 | Bolt-Socket Head; (5/16-18x1-In) | 4 |
| 20***73 | Sensor Group-Speed; (Traction Aid) | 2 |
| 5T***18 | Sensor Group-Speed; (Traction Aid) | 1 |
9g-9629 Sensor Gp-Speed -Transmission
| 14***78 | Sensor Group-Speed | 1 |
| 1B***67 | Ball Bearing | 1 |
| 2A***62 | Screw,Cap,Hexagon H Diode Pig Tail To Grd; (1/4-20x.625 In) | 4 |
129-6628 Sensor Gp-Speed
| 10***13 | Seal; (3 Pin Plug) | 1 |
| 12***28 | Sensor Group-Speed; -Engine Speed/Timing | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
273-5041 Sensor Gp-Speed
| 11***66 | Seal-O-Ring | 1 |
| 13***07 | Washer; (21.1x28.1x0.9-mm Thk) | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
265-9033 Sensor Gp-Speed
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 2 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 3 |
| 19***27 | Harness As-Sensor; (14-Ga Wire)(Engine Oil Temperature) | 3 |
118-7226 Sensor Gp-Temperature
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***26 | Sensor Group-Temperature; -Transmission Oil | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
102-2240 Sensor Gp-Temperature
| 10***40 | Sensor Group-Temperature; -Output Transfer Gear Oil | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
142-5679 Sensor Gp-Temperature
| 11***26 | Sensor Group-Temperature; -Transmission Oil | 1 |
| 13***00 | Clip; (Tab) | 1 |
| 14***79 | Sensor Group-Temperature | 1 |
106-0735 Sensor Gp-Temperature
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***35 | Sensor Group-Temperature; -Engine Oil | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
199-5085 Software Gp-Machine -Traction Control
| 19***85 | Software Group-Machine; -Traction Control | 1 |
199-5082 Software Gp-Machine -Automatic Retarder
| 19***82 | Software Group-Machine; -Automatic Retarder | 1 |
199-5079 Software Gp-Machine -Integrated Brake
| 19***79 | Software Group-Machine; -Integrated Brake | 1 |
142-5683 Starting Aid Ar-Ether
| 14***83 | Starting Aid Ar-Ether | 1 |
| 14***84 | Starting Aid Group-Ether | 1 |
| 14***85 | Starting Aid Group-Ether; -Chassis | 1 |
142-5684 Starting Aid Gp-Ether
| 12***95 | Tube | 1 |
| 14***84 | Starting Aid Group-Ether | 1 |
| 6N***72 | Ether Atomizer--Spray | 1 |
142-5685 Starting Aid Gp-Ether -Chassis
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***00 | Clip; (Tab) | 1 |
| 14***85 | Starting Aid Group-Ether; -Chassis | 1 |
136-3183 Starting Ar-Cold Weather
| 13***83 | Starting Ar-Cold Weather | 1 |
| 13***24 | Battery & Wiring Group; -Cold Weather Starting | 1 |
| 15***79 | Wiring Group-Engine; -Cold Weather | 1 |
6v-0890 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
4n-1061 Starting Motor Gp-Electric
| 4N***59 | Gasket; (Starting Motor) | 1 |
| 4N***61 | Starting Motor Group-Electric | 1 |
| 6V***90 | Starting Motor Group-Electric; (Delco Remy) | 1 |
7n-1059 Starting Motor Gp-Electric
| 10***28 | Wire As | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
| 6V***85 | Starting Motor Group-Electric; -Cold Weather | 1 |
6v-0885 Starting Motor Gp-Electric -Cold Weather
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
142-3985 Switch Gp-Magnetic -Secondary Steering Relay-Engine Prelubrication Relay
| 14***85 | Switch As-Magnetic; -Secondary Steering Relay-Engine Prelubrication Relay | 1 |
| 1B***78 | Nut,Plain,Hexagon Rod To Lever Uoc:Bsv,Bsx | 2 |
| 6V***78 | Nut; (10-32-Thd) | 2 |
142-3984 Switch Gp-Magnetic -Secondary Steering Relay-Engine Prelubrication Relay
| 14***84 | Switch As-Magnetic; -Secondary Steering Relay-Engine Prelubrication Relay | 1 |
| 1B***78 | Nut,Plain,Hexagon Rod To Lever Uoc:Bsv,Bsx | 2 |
| 4D***26 | Washer,Lock Starter Ground Cable, Internal And External Teeth | 2 |
100-4417 Switch Gp-Flow
| 10***17 | Switch Group-Flow; -Engine Coolant | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 0 |
| 17***08 | Switch Group-Flow; -Engine Coolant | 1 |
175-2309 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***81 | Switch As-Magnetic; (Start Relay) | 1 |
3e-0154 Switch Gp-Magnetic -Secondary Steering Relay-Engine Prelubrication Relay
| 3E***54 | Switch Group-Magnetic; -Secondary Steering Relay-Engine Prelubrication Relay | 1 |
| 4D***26 | Washer,Lock Starter Ground Cable, Internal And External Teeth | 2 |
| 6V***78 | Nut; (10-32-Thd) | 2 |
175-2308 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
118-3534 Switch Gp-Magnetic
| 11***34 | Switch Group-Magnetic; -Start Relay | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
| 17***09 | Switch Group-Magnetic; -24-Volt-Start Relay | 1 |
169-0884 Switch Gp-Rocker -Exhaust Diverter
| 16***74 | Lamp-Led; (24-Volt, Cab Floodlight Switch) | 1 |
| 16***84 | Switch Group-Rocker; -Exhaust Diverter | 1 |
| 17***34 | Switch As-Rocker; (Exhaust Diverter) | 0 |
174-3753 Wiring Gp-Automatic Retarder -Cab
| 11***18 | Clip | 1 |
| 13***00 | Clip; (Tab) | 1 |
| 16***57 | Harness As-Valve; (Automatic Retarder Control)(Auto Retarder Control Valve) | 1 |
162-5322 Wiring Gp-Cab
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
136-1811 Wiring Gp-Chassis
| 03***48 | Clip; (11.11mm .437in Id) | 4 |
| 10***08 | Plug-Connector | 1 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
158-8879 Wiring Gp-Engine -Cold Weather
| 13***41 | Cable As | 1 |
| 15***79 | Wiring Group-Engine; -Cold Weather | 1 |
| 18***60 | Harness As-Starting Aid; (Cold Weather) | 1 |
147-1130 Wiring Gp-Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 3 |
| 12***33 | Cover As; (Auxiliary Start Receptacle) | 1 |
118-9692 Wiring Gp-Engine
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 0S***20 | Bolt--Customer Grounding Bolt | 1 |
174-9663 Wiring Gp-Exhaust Diverter
| 17***73 | Harness As-Valve; (Exhaust Diverter) | 1 |
| 17***63 | Wiring Group-Exhaust Diverter | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 3 |
174-3770 Wiring Gp-Integrated Brake
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***46 | Plug As-Connector; (40-Pin) | 1 |
| 11***48 | Plug As-Connector; (40-Pin) | 1 |
143-0028 Wiring Gp-Monitor -Payload
| 13***78 | Cap; (Fuse Holder) | 1 |
| 14***28 | Wiring Group-Monitor; -Payload | 1 |
| 16***45 | Harness As-Control; (Payload)(Tpms) | 1 |
157-1651 Wiring Gp-Prelubrication -Cab
| 13***24 | Film-Notice; (Prelubrication)(Key Start) | 1 |
| 13***78 | Cap; (Fuse Holder) | 1 |
| 15***51 | Wiring Group-Prelubrication; -Cab | 1 |
157-1642 Wiring Gp-Prelubrication -Chassis
| 15***49 | Cable As | 1 |
| 15***50 | Cable As | 1 |
| 15***42 | Wiring Group-Prelubrication; -Chassis | 1 |
137-6813 Wiring Gp-Sensor -Payload
| 13***00 | Clip; (Tab) | 4 |
| 13***13 | Wiring Group-Sensor; -Payload Monitoring | 1 |
| 18***03 | Harness As-Sensor; (Payload Monitoring) | 1 |
157-1643 Wiring Gp-Sensor -Wheel Speed
| 15***55 | Kit; (Connecting Plug) (12-Pin) (Includes Plug As Wedge & Interface Seal) | 1 |
| 15***43 | Wiring Group-Sensor; -Wheel Speed | 1 |
| 15***40 | Harness As-Sensor; (Tcs) | 1 |
174-3728 Wiring Gp-Traction Control -Cab
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***46 | Plug As-Connector; (40-Pin) | 1 |
| 11***48 | Plug As-Connector; (40-Pin) | 1 |
109-0401 Wiring Gp-Unit Injector
| 03***34 | Seal-O-Ring | 1 |
| 10***61 | Clip | 1 |
| 10***01 | Wiring Group-Unit Injector | 1 |
Engine Arrangement
131-4877 Engine Ar
| 10***17 | Switch Group-Flow; -Engine Coolant | 1 |
| 10***52 | Cylinder Head Group | 1 |
| 10***53 | Camshaft Group | 1 |
144-3577 Engine Ar-Core
| 10***17 | Switch Group-Flow; -Engine Coolant | 1 |
| 10***52 | Cylinder Head Group | 1 |
| 10***53 | Camshaft Group | 1 |
143-7473 Engine Ar-General
| 12***58 | Installation Ar-Engine | 1 |
| 14***74 | Kit-Gasket; (Aftercooler & Lines) | 0 |
| 14***75 | Kit-Gasket; (Air Compressor Installation) | 0 |
128-8558 Installation Ar-Engine
| 12***23 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
| 12***46 | Filler Group-Engine Oil | 1 |
| 12***65 | Drive Group-Fan | 1 |
Frame And Body
143-7111 Body & Canopy As-Dual Slope -European Market
| 13***06 | Guard As | 1 |
| 14***61 | Canopy As | 1 |
| 14***11 | Body & Canopy As-Dual Slope; -European Market | 1 |
137-7266 Body & Canopy As-Flat Floor -European Market
| 13***90 | Body As-Dump | 1 |
| 13***95 | Bracket As | 2 |
| 13***66 | Body & Canopy As-Flat Floor; -European Market | 1 |
251-9535 Body Gp-Dual Slope
| 11***64 | Guard As; (Lh) | 1 |
| 11***65 | Guard As; (Rh) | 1 |
| 13***06 | Guard As | 1 |
137-7155 Body Gp-Dual Slope
| 11***64 | Guard As; (Lh) | 1 |
| 11***65 | Guard As; (Rh) | 1 |
| 13***55 | Body Group-Dual Slope | 1 |
137-7156 Body Gp-Dual Slope
| 13***56 | Body Group-Dual Slope | 1 |
137-2081 Body Gp-Flat Floor
| 13***81 | Body Group-Flat Floor | 1 |
136-3165 Body Gp-Flat Floor
| 11***64 | Guard As; (Lh) | 1 |
| 11***65 | Guard As; (Rh) | 1 |
| 13***65 | Body Group-Flat Floor | 1 |
128-2578 Cowling Gp
| 12***78 | Cowling Group | 1 |
| 12***04 | Cowling As | 1 |
| 12***85 | Baffle As | 1 |
136-1810 Fender Gp
| 12***97 | Fender As | 1 |
| 13***10 | Fender Group | 1 |
| 13***34 | Plate | 1 |
126-7562 Frame As
| 12***61 | Frame As | 1 |
| 12***62 | Frame As | 1 |
| 7D***07 | Bearing-Sleeve | 2 |
126-7561 Frame As
| 11***32 | Support As | 1 |
| 11***95 | Support As | 1 |
| 12***61 | Frame As | 1 |
126-7563 Frame Gp
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 8 |
| 12***98 | Tube As | 1 |
| 12***62 | Frame As | 1 |
136-1806 Guard Gp-Drive Shaft
| 12***95 | Guard As | 1 |
| 13***06 | Guard Group-Drive Shaft | 1 |
| 16***36 | Guard As | 1 |
136-1799 Handhold Gp -Platform
| 0T***83 | Washer--Junction Box To Rear Support | 2 |
| 13***99 | Handhold Group; (Platform) | 1 |
| 14***25 | Rail As | 1 |
136-1809 Hood Gp-Truck
| 0T***83 | Washer--Junction Box To Rear Support | 1 |
| 10***93 | Rivet-Pop; (103 Deg Cntrsunk) | 6 |
| 10***65 | Latch As-Compartment | 1 |
128-6940 Ladder Gp
| 12***25 | Ladder As | 2 |
| 12***40 | Ladder Group | 1 |
| 2A***89 | Step As | 2 |
137-3454 Liner Gp-Body -Flat Floor
| 12***59 | Plate-Canopy | 2 |
| 13***54 | Liner Group-Body; -Flat Floor | 1 |
| 13***57 | Plate | 2 |
136-3181 Liner Gp-Body -Dual Slope
| 12***59 | Plate-Canopy | 2 |
| 12***23 | Plate | 1 |
| 12***25 | Plate | 2 |
155-4437 Mirror Gp-Rear View
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 15***36 | Bracket As | 1 |
| 15***37 | Mirror Group-Rear View | 1 |
155-4464 Mirror Gp-Rear View
| 15***37 | Mirror Group-Rear View | 1 |
| 15***64 | Mirror Group-Rear View | 1 |
| 3B***05 | Pin Split Cotter | 2 |
136-4627 Mounting Gp-Truck Body
| 03***31 | Bolt; (3/8-16x3.75-In)(Shield As. To Heads) | 2 |
| 05***88 | Washer; (13.5x30x3-mm Thk) | 4 |
| 10***22 | Shim; (8.0mm Thk) | 1 |
116-3092 Suspension Gp-Front
| 10***68 | Piston | 1 |
| 11***61 | Seal-O-Ring | 2 |
| 11***92 | Suspension Group-Front | 1 |
9d-7340 Suspension & Mtg Gp-Front
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 6 |
| 11***46 | Cover | 2 |
| 11***92 | Suspension Group-Front | 2 |
9d-7350 Suspension Gp-Rear
| 11***37 | Suspension Group-Rear | 2 |
| 12***11 | Cover | 2 |
| 19***85 | Block | 2 |
116-2837 Suspension Gp-Rear
| 10***93 | Head | 1 |
| 10***56 | Rod As | 1 |
| 11***61 | Seal-O-Ring | 2 |
129-7234 Tread Gp-Non-Skid
| 03***66 | Tread-Anti-Skid | 1 |
| 12***21 | Tread | 1 |
| 12***22 | Tread | 1 |
113-0656 Walkway Gp
| 11***56 | Walkway Group | 1 |
| 11***90 | Walkway As | 1 |
| 11***71 | Rail As | 1 |
Fuel System
9d-9880 Adapter Gp-Fast Fill Fuel
| 12***71 | Clamp-Hose | 1 |
| 2G***00 | Valve As-Tank | 1 |
| 5M***62 | Bolt; (3/8-16x0.75-In) | 1 |
125-3431 Drive Gp-Unit Inj Hyd Pump
| 11***35 | Pin | 1 |
| 12***31 | Drive Group-Unit Inj Hydraulic Pump | 1 |
| 16***26 | Sensor Group-Pressure; -Atmospheric Air, Turbo Inlet | 1 |
162-0149 Drive Gp-Unit Inj Hyd Pump
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 10***27 | Gasket | 1 |
125-3430 Drive Gp-Unit Inj Hyd Pump
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 10***27 | Gasket | 1 |
180-6644 Drive Gp-Unit Inj Hyd Pump
| 03***01 | Bolt; --To Reverse Shaft Bearing Retainer | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 12***40 | Plate | 1 |
232-1176 Injector Gp-Fuel
| 11***98 | Adapter-Injection | 1 |
| 11***22 | Seal-Rectangular | 1 |
| 13***69 | Bolt-Socket Head | 2 |
159-0836 Injector Gp-Fuel
| 11***98 | Adapter-Injection | 1 |
| 11***22 | Seal-Rectangular | 1 |
| 13***69 | Bolt-Socket Head | 2 |
138-8756 Injector Gp-Fuel
| 11***98 | Adapter-Injection | 1 |
| 11***22 | Seal-Rectangular | 1 |
| 13***69 | Bolt-Socket Head | 2 |
138-6256 Kit-Seal -Unit Injector Hydraulic Pump
| 03***53 | Seal-O-Ring; (08.92mm Id) | 3 |
| 03***27 | Seal-O-Ring; (19.18mm Id) | 2 |
| 03***39 | Seal-O-Ring (Id=9.25mm) | 1 |
136-1813 Lines Gp-Fuel
| 12***74 | Clip-Loop; (12.7mm Id) | 1 |
| 12***30 | Bracket As | 1 |
| 13***13 | Lines Group-Fuel; -Chassis | 1 |
151-1356 Lines Gp-Fuel Filter
| 03***33 | Seal-O-Ring; (12.42mm Id) | 4 |
| 09***87 | Tee | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 1 |
129-6837 Lines Gp-Fuel Filter
| 03***33 | Seal-O-Ring; (12.42mm Id) | 4 |
| 09***87 | Tee | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 1 |
109-0399 Lines Gp-Injector Hyd Pump
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 3 |
| 10***02 | Tube As | 1 |
| 10***99 | Lines Group-Injector Hydraulic Pump | 1 |
126-7292 Pump & Mtg Gp-Unit Inj Hyd
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 4 |
108-7090 Pump Gp-Fuel Injection
| 10***26 | Clamp-Injector | 1 |
| 10***90 | Pump Group-Fuel Injection | 1 |
| 11***21 | Seal-Rectangular | 2 |
122-2513 Pump Gp-Fuel Prm & Prim Filter
| 10***08 | Pump As; (Fuel Priming) | 1 |
| 12***13 | Pump Group-Fuel Prm & Prim Filter | 1 |
| 12***57 | Base As-Filter; (Primary Fuel Filter) | 1 |
201-4202 Pump Gp-Unit Injector Hyd
| 10***77 | Valve Group-Solenoid; -Pressure Control | 1 |
| 13***52 | Seal-O-Ring | 1 |
| 13***09 | Fitting | 2 |
144-0835 Pump Gp-Unit Injector Hyd
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 4 |
| 10***77 | Valve Group-Solenoid; -Pressure Control | 1 |
| 11***20 | Coupling | 1 |
169-1034 Pump Gp-Unit Injector Hyd
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 4 |
| 10***77 | Valve Group-Solenoid; -Pressure Control | 1 |
| 11***20 | Coupling | 1 |
201-4201 Pump Gp-Unit Injector Hyd
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 4 |
| 11***20 | Coupling | 1 |
| 14***50 | Pump Group-Fuel Transfer | 1 |
212-1439 Sender Gp-Fuel Level
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 21***39 | Sender Group-Fuel Level | 1 |
136-1812 Tank Gp-Fuel
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 0S***27 | Bolt -114.30 mm(4.50 In.) Long | 1 |
| 13***18 | Plate As | 1 |
141-8550 Tank Gp-Fuel
| 14***50 | Tank Group-Fuel | 1 |
| 1H***05 | Block | 1 |
| 1H***06 | Screw-Purge (1/2-20x1.625in); (1/2-20x1.625-In) | 1 |
2g-9000 Valve As-Tank -Fast Fill Fuel
| 2G***00 | Valve As-Tank | 1 |
102-7535 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 10***35 | Valve Group-Check; -Fuel Return Port | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 1 |
107-0677 Valve Gp-Solenoid
| 03***28 | Seal-O-Ring | 1 |
| 03***39 | Seal-O-Ring (Id=9.25mm) | 1 |
| 10***77 | Valve Group-Solenoid; -Pressure Control | 1 |
Hydraulic System
118-5081 Actuator Gp-Pilot Control -Hoist
| 11***81 | Actuator Group-Pilot Control; -Auxiliary Dual Stage, Hoist | 1 |
| 14***55 | Cylinder Group-Hoist; -Telescoping | 2 |
| 5P***66 | Capscrew; (Hex Hd) (1/2-13 Nc X 1 1/2) (Gd 8 Z) | 4 |
145-5252 Cylinder & Mtg Gp-Hoist
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 14***52 | Cylinder & Mtg Group-Hoist | 1 |
| 1D***86 | Bolt (3.50" Long--.625" Dia.) | 6 |
145-5155 Cylinder Gp-Hoist -Telescoping
| 13***11 | Lines Group-Hoist | 1 |
| 13***12 | Lines Group-Power Train Oil | 1 |
| 13***13 | Lines Group-Hydraulic Oil Cooler | 1 |
136-1801 Hydraulic Ar
| 11***37 | Tube As | 1 |
| 11***32 | Block | 1 |
| 13***42 | Tube As | 1 |
135-9411 Lines Gp-Hoist
| 13***41 | Tube As | 1 |
| 13***11 | Lines Group-Hoist | 1 |
| 13***39 | Hose As | 1 |
135-9413 Lines Gp-Hydraulic Oil Cooler
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 2 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 11***32 | Cover | 1 |
131-3753 Mounting Gp-Hydraulic Tank -Brake, Hoist
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 11***68 | Gasket | 1 |
| 13***53 | Mounting Group-Hydraulic Tank; -Brake, Hoist | 1 |
175-7051 Pump & Motor Gp-Hydraulic -Secondary Steering, Brake Release, High Speed Oil Change
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 14***08 | Flange As | 1 |
| 14***80 | Body As | 1 |
331-8600 Pump Gp-Gear
| 11***99 | Pump Group-Gear; -Brake Release, Hoist | 1 |
| 14***46 | Pump Group-Piston; -Steering | 1 |
| 16***08 | Bracket As | 1 |
111-8399 Pump Gp-Gear -Brake Release, Hoist
| 09***95 | Pin, Dowel | 8 |
| 11***99 | Pump Group-Gear; -Brake Release, Hoist | 1 |
| 13***35 | Seal-Shaft | 1 |
136-1805 Pump Gp-Hydraulic -Brake, Hoist, Steering
| 08***19 | Pin | 1 |
| 09***05 | Bolt-Socket Head; (M14x2x40-mm) | 4 |
| 10***43 | Shaft-Pump | 1 |
178-5195 Pump Gp-Piston -Steering
| 09***05 | Bolt-Socket Head; (M14x2x40-mm) | 4 |
| 10***79 | Cone-Bearing | 1 |
| 12***94 | Plug; (Break Off) | 1 |
219-1964 Pump Gp-Piston
| 12***24 | Plate-Valve | 1 |
| 16***79 | Pin | 3 |
| 19***26 | Barrel | 1 |
145-5246 Pump Gp-Piston -Steering
| 09***05 | Bolt-Socket Head; (M14x2x40-mm) | 4 |
| 10***79 | Cone-Bearing | 1 |
| 12***27 | Piston-Control | 1 |
196-0227 Rotating Gp-Pump -Steering
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 70 |
| 10***03 | Gauge-Sight; (Hydraulic Oil Level) | 1 |
120-5726 Rotating Gp-Pump -Steering
| 12***26 | Rotating Group-Pump; -Steering | 1 |
| 16***79 | Pin | 3 |
| 19***19 | Plate | 1 |
6e-4006 Rotating Gp-Pump
| 12***24 | Plate-Valve | 1 |
| 16***79 | Pin | 3 |
| 19***26 | Barrel | 1 |
153-2739 Tank Gp-Hydraulic -Brake, Hoist
| 14***30 | Valve Group-Control; -Hoist | 1 |
| 15***39 | Tank Group-Hydraulic; -Brake, Hoist | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 3 |
151-4533 Valve & Mtg Gp-Control -Hoist
| 15***33 | Valve & Mtg Group-Control; -Hoist | 1 |
| 19***65 | Valve Group-Control; -Hoist | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 3 |
194-1628 Valve & Mtg Gp-Control
| 03***06 | Seal (Use As Required) | 1 |
| 10***83 | Valve Group | 1 |
| 10***84 | Valve Group | 1 |
194-1465 Valve Gp-Control -Hoist
| 03***43 | Seal-O-Ring | 1 |
| 10***45 | Valve-Orifice; (Hydraulic Oil Check) | 1 |
| 19***36 | Spring | 1 |
148-3530 Valve Gp-Control -Hoist
| 03***06 | Seal (Use As Required) | 1 |
| 10***83 | Valve Group | 1 |
| 10***84 | Valve Group | 1 |
184-5173 Valve Gp-Pump Control -Pressure, Flow Compensator-Steering Pump
| 03***43 | Seal-O-Ring | 1 |
| 10***45 | Valve-Orifice; (Hydraulic Oil Check) | 1 |
| 18***73 | Valve Group-Pump Control; -Pressure, Flow Compensator-Steering Pump | 1 |
196-0228 Valve Gp-Pump Control -Steering Pump
| 11***78 | Body | 1 |
| 11***58 | Body As | 1 |
| 11***97 | Spring | 1 |
135-6616 Valve Gp-Pump Control -Pressure, Flow Compensator-Steering Pump
| 03***43 | Seal-O-Ring | 1 |
| 10***45 | Valve-Orifice; (Hydraulic Oil Check) | 1 |
| 13***16 | Valve Group-Pump Control; -Pressure, Flow Compensator-Fan, Impl Pilot, Axle Cooler | 1 |
106-7372 Valve Gp-Relief -Hoist Low Pressure, Lower
| 10***72 | Valve Group-Relief; -Hoist Low Pressure, Lower | 1 |
| 11***78 | Body | 0 |
| 1J***97 | Valve; (Push-Pull) | 1 |
148-2962 Valve Gp-Relief
| 11***86 | Anchor | 1 |
| 11***92 | Rod | 1 |
| 13***38 | Washer-Plastic; (13x31.7x0.8-mm Thk) | 2 |
Lubrication System
6n-3925 Extension Gp-Drain -Engine Oil
| 1F***74 | Elbow Block & Aftercooler | 1 |
| 6B***56 | Nipple (4" Long) | 1 |
| 6N***25 | Extension Group-Drain; -Engine Oil | 1 |
119-8583 Fastener Gp-Oil Pump Mounting -Engine
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 11***83 | Fastener Group-Oil Pump Mounting; -Engine | 1 |
122-5846 Filler Gp-Engine Oil
| 12***46 | Filler Group-Engine Oil | 1 |
| 12***48 | Tube As-Oil Filler | 1 |
| 12***49 | Bracket-Oil Filler | 1 |
4n-2357 Filter Gp-Engine Oil
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 1R***08 | Filter As-Engine Oil; (Advanced Efficiency)(High Efficiency) | 2 |
| 2P***03 | Base As-Oil Filter; (Engine) | 2 |
142-5682 Fitting Gp-High Spd Oil Change
| 03***65 | Elbow (45 Degrees) | 1 |
| 14***82 | Fitting Group-High Spd Oil Change | 1 |
| 1P***19 | Coupler (Use With .75 In Hose) | 1 |
136-7608 Fumes Disposal Gp
| 12***29 | Tube | 1 |
| 12***47 | Tube As | 1 |
| 13***74 | Clip-Loop | 2 |
122-2523 Gauge Gp-Oil Level (Dipstick) -Engine
| 10***59 | Spacer; (9x20x39.2-mm Thk) | 1 |
| 11***68 | Seal-O-Ring; (15.54mm Id) | 1 |
| 12***14 | Bracket As | 1 |
142-5681 Lines Gp-Engine Oil -High Speed
| 14***81 | Lines Group-Engine Oil; -High Speed | 1 |
| 3B***32 | Elbow Oil Pan Drain | 1 |
| 6B***81 | Bushing; (Reducing) | 1 |
122-1790 Lines Gp-Engine Oil
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
122-1898 Lines Gp-Engine Oil Filter
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 6 |
142-5657 Lines Gp-Prelubrication
| 09***08 | Hose As | 1 |
| 13***94 | Hose As | 1 |
| 14***57 | Lines Group-Prelubrication | 1 |
129-6833 Lines Gp-Turbocharger Oil
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 6 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 11***26 | Tube As-Drain | 1 |
142-5680 Oil Change Ar-High Speed
| 14***80 | Oil Change Ar-High Speed | 1 |
| 14***81 | Lines Group-Engine Oil; -High Speed | 1 |
| 14***82 | Fitting Group-High Spd Oil Change | 1 |
158-8892 Prelubrication Ar-Engine
| 14***57 | Lines Group-Prelubrication | 1 |
| 14***58 | Pump Group-Prelubrication | 1 |
| 15***42 | Wiring Group-Prelubrication; -Chassis | 1 |
134-1416 Pump & Motor Gp-Prelubrication
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 13***16 | Pump & Motor Group-Prelubrication; -Engine Prelubrication | 1 |
| 13***17 | Pump | 1 |
116-1980 Pump Gp-Engine Oil
| 10***82 | Shaft As-Pump Drive | 1 |
| 10***73 | Shaft As-Idler | 1 |
| 11***79 | Body As-Oil Pump | 1 |
142-5658 Pump Gp-Prelubrication
| 13***16 | Pump & Motor Group-Prelubrication; -Engine Prelubrication | 1 |
| 14***58 | Pump Group-Prelubrication | 1 |
| 2P***21 | Adapter; (1-1/16-12) | 1 |
Machine Arrangement
136-1800 Chassis Ar
| 10***10 | Brake Group; -Front Caliper | 1 |
| 11***56 | Walkway Group | 1 |
| 11***43 | Mounting Group-Cab | 1 |
131-3773 General Ar
| 13***42 | Cab Ar | 1 |
| 13***46 | Power Train Ar | 1 |
| 13***73 | General Ar | 1 |
Operator Station
5d-6998 Horn Gp-Air
| 10***39 | Bracket | 1 |
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 1 |
| 10***86 | Hose As | 1 |
2g-1150 Horn Gp-Air -Chassis
| 15***87 | Cover | 2 |
| 2G***50 | Horn Group-Air; -Chassis | 1 |
| 2G***64 | Kit-Diaphragm; (Air Horn) | 2 |
173-1028 Adjuster Gp-Seat
| 11***92 | Rod | 1 |
| 13***38 | Washer-Plastic; (13x31.7x0.8-mm Thk) | 2 |
| 13***44 | Latch Assem.; (Lh) | 1 |
170-1111 Adjuster Gp-Seat
| 11***86 | Anchor | 1 |
| 11***92 | Rod | 1 |
| 13***38 | Washer-Plastic; (13x31.7x0.8-mm Thk) | 2 |
142-5655 Air Conditioner Ar
| 03***26 | Retainer | 1 |
| 06***93 | Grommet; (Rh) | 1 |
| 10***43 | Plate-Orifice | 2 |
118-3533 Air Conditioner Ar
| 11***33 | Air Conditioner Ar | 1 |
| 12***07 | Compressor Group-Refrigerant | 1 |
| 14***56 | Lines Group-Air Conditioner | 1 |
113-0746 Air Conditioner Ar
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 1 |
| 11***46 | Air Conditioner Ar | 1 |
| 11***77 | Air Conditioner Group; -Cab | 1 |
117-5177 Air Conditioner Gp
| 11***77 | Air Conditioner Group; -Cab | 1 |
| 3E***12 | Nut-Square; (3/8-16-Thd) | 1 |
| 6V***87 | Screw-Pan Head; (10-24x1-In) | 4 |
129-0297 Armrest Gp -Rh-Adjustable
| 12***97 | Armrest Group; -Rh-Adjustable | 1 |
| 13***38 | Washer-Plastic; (13x31.7x0.8-mm Thk) | 2 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 1 |
169-8607 Armrest Gp -Rh
| 10***40 | Visor Group-Cab | 1 |
| 11***76 | Heater Group-Cab | 1 |
| 13***61 | Control Group-Hoist; -Cab | 1 |
8y-5904 Armrest Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 12***98 | Plate As-Slide | 1 |
| 12***99 | Bracket As | 1 |
131-3742 Cab Ar
| 13***42 | Cab Ar | 1 |
| 16***88 | Control Group-Retarder; -Cab | 1 |
| 17***53 | Wiring Group-Automatic Retarder; -Cab | 1 |
174-3750 Cab Ar
| 16***88 | Control Group-Retarder; -Cab | 1 |
| 17***50 | Cab Ar; -Automatic Retarder Control | 1 |
| 17***70 | Wiring Group-Integrated Brake | 1 |
174-3768 Cab Ar
| 10***08 | Bracket As | 1 |
| 10***62 | Liner As-Cab | 1 |
| 12***05 | Cover | 1 |
137-0090 Cab Gp
| 10***83 | Liner | 1 |
| 10***86 | Liner | 1 |
| 10***89 | Glass | 1 |
136-1819 Cab Gp
| 10***83 | Liner | 1 |
| 10***88 | Glass | 1 |
| 10***89 | Glass | 1 |
128-3207 Compressor Gp-Refrigerant
| 12***07 | Compressor Group-Refrigerant | 1 |
| 12***95 | Bracket | 1 |
| 1F***50 | Nut Rops Support | 2 |
3e-1906 Compressor Gp-Refrigerant
| 09***81 | Spacer; (10.5x20x10.0mm Thk) | 1 |
| 11***68 | Guard As | 1 |
| 1F***50 | Nut Rops Support | 3 |
128-6613 Condenser & Mtg Gp-Refrigerant
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***58 | Washer; (6.5x17x1-mm Thk) | 4 |
| 12***56 | Cover As | 1 |
137-0057 Console Gp-Operator
| 11***18 | Clip | 1 |
| 13***37 | Control Group-Hoist Electronic; -Positioning Lever | 1 |
| 13***59 | Plate As | 1 |
131-3761 Control Gp-Hoist
| 13***61 | Control Group-Hoist; -Cab | 1 |
| 13***79 | Sensor Group-Position; -Hoist Control | 1 |
| 14***23 | Lever As; (Body Dump) | 1 |
136-4837 Control Gp-Hoist Electronic
| 13***37 | Control Group-Hoist Electronic; -Positioning Lever | 1 |
| 14***00 | Screw | 2 |
| 16***11 | Kit-Handle; (Hoist Control) | 1 |
146-6293 Control Gp-Monitor -Caterpillar Monitoring System
| 14***93 | Control Group-Monitor; -Caterpillar Monitoring System | 1 |
183-3561 Control Gp-Monitor -Caterpillar Monitoring System
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 00***54 | Nipple-Pipe | 2 |
| 14***16 | Valve Group-Relay; (Auto Retarder Ctrl Brake Air) | 1 |
103-5526 Control Gp-Monitor -Backlight Dimmer
| 10***26 | Control Group-Monitor Sys Dimmer; -Backlight Dimmer | 1 |
| 25***03 | Control Group-Unprogrammed; (Caterpillar Monitoring System)(Caterpillar Monitoring System) | 1 |
9x-6846 Control Gp-Monitor -Payload
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 5P***32 | Screw-Washer Head; 4.76mm(.187in)Long | 2 |
9x-5308 Display Gp-Payload Monitor -Operator Display
| 8C***81 | Film-Instruction; (Payload Measurement) | 1 |
| 9X***08 | Control Group-Payload Electronic; -Operator Display | 2 |
9x-6847 Display Gp-Payload Monitor -Operator Display
| 11***58 | Washer; (6.5x17x1-mm Thk) | 9 |
| 12***65 | Knob; (Black Plastic) | 1 |
| 12***72 | Panel As-Door; (Rh) | 1 |
163-6388 Control Gp-Retarder
| 00***33 | Tee-Pipe | 1 |
| 12***61 | Valve & Mtg Group-Brake; -Automatic Retarder | 1 |
| 16***88 | Control Group-Retarder; -Cab | 1 |
139-5225 Control Gp-Retarder -Chassis
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 2 |
| 00***54 | Nipple-Pipe | 1 |
| 13***25 | Control Group-Retarder; -Chassis | 1 |
127-9163 Door Gp-Cab -Rh
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 4 |
| 10***49 | Switch As; (24-Volt)(Right Conveyor On/Off) | 1 |
137-0077 Door Gp-Cab -Lh
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 4 |
| 11***58 | Washer; (6.5x17x1-mm Thk) | 10 |
8y-6883 Extension Gp-Backrest -Cloth
| 5H***49 | Clip | 3 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 1 |
| 5S***79 | Hex Head Capscrew, 3/8 Nc X 7/8 In. (22 mm) | 1 |
142-5646 Fastener Gp-Heater Lines -Cab Heater
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 4 |
| 10***66 | Filter Element-Cab Air; (Standard Efficiency) | 1 |
| 11***09 | Knob-Control | 1 |
118-6383 Heater Gp-Cab
| 11***83 | Heater Group-Cab | 1 |
| 2G***33 | Bracket | 1 |
| 2H***23 | Grommet (1.375" Inside Diameter) | 1 |
117-5276 Heater Gp-Cab
| 03***26 | Retainer | 1 |
| 10***43 | Plate-Orifice | 2 |
| 10***26 | Wheel As-Blower | 2 |
142-5654 Lines Gp-Air Conditioner -Cab
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 1 |
| 10***95 | Valve As | 1 |
| 10***96 | Gasket | 1 |
142-5656 Lines Gp-Air Conditioner
| 14***56 | Lines Group-Air Conditioner | 1 |
| 5P***58 | Sleeve; (Cable Splice) | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
6v-1970 Literature Gp
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 6V***70 | Literature Group; (Literature Compartment) | 1 |
125-6806 Module Gp-Speedometer & Tach
| 11***52 | Sensor & Mtg Group-Payload | 1 |
| 12***06 | Module Group-Speedometer & Tach | 1 |
| 13***13 | Wiring Group-Sensor; -Payload Monitoring | 1 |
142-9905 Monitor Ar-Payload
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 14***05 | Monitor Ar-Payload | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 5 |
147-7975 Motor Gp-Window Wiper
| 14***75 | Motor Group-Window Wiper; -Cab Door, Lh | 1 |
| 16***42 | Mount; (Cab) | 32 |
| 16***27 | Sleeve | 12 |
117-5043 Mounting Gp-Cab
| 11***43 | Mounting Group-Cab | 1 |
| 3B***53 | Bolt- 114.30 mm(4.50 In.) Long | 4 |
| 5P***48 | Washer--Bracket To L.H. Support Rail | 4 |
159-5279 Mounting Gp-Platform
| 10***23 | Shaft As-Lumbar | 1 |
| 10***24 | Pan-Lumbar | 1 |
| 15***79 | Mounting Group-Platform | 1 |
218-0864 Pan Gp-Backrest -Cloth
| 21***64 | Pan Group-Backrest; -Cloth | 1 |
| 3K***97 | Pin 3.18 mm(.125 In.) Diameter | 4 |
| 6V***56 | Ring-Retaining | 2 |
186-3059 Pan Gp-Backrest -Cloth
| 13***43 | Plate As-Lumbar | 1 |
| 16***83 | Knob-Lumbar | 1 |
| 17***52 | Retainer | 1 |
162-7776 Pan Gp-Backrest
| 11***04 | Cushion As-Back | 1 |
| 13***43 | Plate As-Lumbar | 1 |
| 16***76 | Pan Group-Backrest; -Lumbar, Suspension Seat | 1 |
108-8421 Pan Gp-Backrest -Lumbar
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
| 11***04 | Cushion As-Back | 1 |
| 13***43 | Plate As-Lumbar | 1 |
8y-5992 Pan Gp-Seat
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***09 | Knob-Control | 1 |
140-8489 Panel Gp-Instrument
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***09 | Knob-Control | 1 |
173-1072 Panel Gp-Instrument
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***09 | Knob-Control | 1 |
| 11***87 | Start Switch Assembly; (Key)(Engine) | 1 |
140-8488 Panel Gp-Instrument
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***06 | Module Group-Speedometer & Tach | 1 |
| 12***95 | Gasket-Panel | 1 |
183-4464 Panel Gp-Instrument
| 12***31 | Cover | 1 |
| 13***24 | Plate As | 1 |
| 13***38 | Pedal As | 1 |
137-0013 Pedal Gp-Governor
| 13***55 | Tank Group-Air; -Primary | 1 |
| 13***15 | Control Group-Service Brake; -Platform | 1 |
| 13***28 | Tank Group-Hydraulic | 1 |
159-5278 Platform Ar
| 14***06 | Support As | 1 |
| 14***29 | Cover As | 1 |
| 15***86 | Cover As; (Access)(Bat Disconnect, Mach Lockout) | 1 |
137-5925 Platform Gp
| 13***25 | Platform Group | 1 |
| 14***06 | Support As | 1 |
| 14***29 | Cover As | 1 |
188-2786 Platform Gp -Rh
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 13***08 | Latch-Recliner | 1 |
| 13***09 | Gear As-Lh | 1 |
168-6873 Recliner Gp-Seat
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 1 |
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 1 |
| 16***46 | Spring | 1 |
186-3058 Recliner Gp-Seat
| 0T***44 | Bolt (1.25" Long) | 1 |
| 0T***89 | Cap Screw (2" Long) | 1 |
| 18***58 | Recliner Group-Seat; -Suspension | 1 |
156-3804 Seat Belt Gp -Operator
| 12***82 | Seat Group | 1 |
| 12***97 | Armrest Group; -Rh-Adjustable | 1 |
| 15***48 | Seat Belt Group; -Retractable-Operator | 1 |
156-1148 Seat Belt Gp -Retractable
| 15***48 | Seat Belt Group; -Retractable-Operator | 1 |
156-1146 Seat Belt Gp -Retractable
| 15***46 | Seat Belt Group; -Retractable | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 1L***80 | Bolt; (7/16-20x1.5-In) | 1 |
186-3056 Seat Gp -Cloth
| 09***93 | Pin-Cotter | 2 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 8 |
| 17***30 | Screw-Button Head; (3/8-16x1-In) | 6 |
169-9506 Seat Gp -Operator
| 11***89 | Extension Group-Backrest | 1 |
| 16***07 | Armrest Group; -Rh-Suspension Seat | 1 |
| 16***06 | Seat Group; -Operator-Air | 1 |
128-0616 Seat Gp
| 06***03 | Shim (.060mm Thk); (1.52-mm Thk) | 4 |
| 09***78 | Pin-Spring | 1 |
| 09***14 | Pin, Clevis | 1 |
128-7982 Seat Gp
| 09***43 | Pin-Cotter | 2 |
| 11***06 | Cushion As | 1 |
| 12***82 | Seat Group | 1 |
186-3051 Seat Gp -Cloth
| 09***93 | Pin-Cotter | 2 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 8 |
| 17***30 | Screw-Button Head; (3/8-16x1-In) | 6 |
162-8449 Seat Gp
| 0T***89 | Cap Screw (2" Long) | 1 |
| 11***89 | Extension Group-Backrest | 1 |
| 11***02 | Cover | 1 |
137-0091 Seat Gp-Companion
| 12***16 | Seat Group | 1 |
| 13***91 | Seat Group-Companion | 1 |
| 13***74 | Support As | 1 |
136-4624 Seat Gp-Suspension
| 13***24 | Seat Group-Suspension | 1 |
| 16***80 | Bolt-Socket Head; (3/8-16x0.375-In) | 1 |
| 16***16 | Suspension Group-Seat; -Adjustable-Operator | 1 |
169-9507 Seat Gp-Suspension -Air
| 16***07 | Seat Group-Suspension; -Air | 2 |
| 17***02 | Support As | 1 |
| 1F***50 | Nut Rops Support | 4 |
180-7309 Seat Gp-Suspension -Cloth, Lumbar
| 10***17 | Bumper | 2 |
| 12***57 | Shaft | 2 |
| 12***28 | Kit-Roller; (Incls Parts Marked S) | 1 |
175-3401 Seat Gp-Suspension -Air
| 13***74 | Support As | 1 |
| 17***01 | Seat Group-Suspension; -Air | 1 |
| 18***09 | Seat Group-Suspension; -Cloth, Lumbar | 1 |
169-8716 Suspension Gp-Seat
| 10***03 | Fastener | 26 |
| 10***11 | Screw-Machine; (3/8-16x0.75-In) | 1 |
| 14***26 | Film-Instruction; (Seat Adjustment) | 1 |
150-7719 Suspension Gp-Seat
| 10***17 | Bumper | 2 |
| 12***57 | Shaft | 2 |
| 12***28 | Kit-Roller; (Incls Parts Marked S) | 1 |
199-5727 Suspension Gp-Seat -Air
| 05***12 | Cartridge As | 1 |
| 06***04 | Ring-Retaining | 1 |
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 2 |
165-2136 Valve Gp-Air Control -Manual Retarder
| 00***89 | Valve As-Drain | 2 |
| 16***36 | Valve Group-Air Control; -Manual Retarder | 1 |
| 1L***79 | Elbow-Pipe; (3/8 In Pipe) | 2 |
153-8338 Valve Gp-Air Control -Secondary Brake Pedal
| 15***38 | Valve Group-Air Control; -Secondary Brake Pedal | 1 |
| 17***76 | Valve As | 1 |
| 2G***43 | Handle | 1 |
143-8994 Valve Gp-Air Control -Service Brake Pedal
| 11***29 | Boot | 1 |
| 14***94 | Valve Group-Air Control; -Service Brake Pedal | 1 |
| 20***70 | Valve As | 1 |
142-5647 Valve Gp-Shutoff -Cab Heater
| 14***47 | Valve Group-Shutoff; -Cab Heater-Engine To Cab Heater | 1 |
| 1D***77 | Bolt-Round Head; (3/8-16x1-In) | 2 |
| 2S***17 | Nut,Plain,Castellat; (3/8-16-Thd) | 1 |
106-8340 Visor Gp-Cab
| 10***40 | Visor Group-Cab | 1 |
| 11***28 | Fitting | 1 |
| 14***95 | Hose; (650-cm Each) | 0 |
163-1877 Washer Gp-Window -Cab
| 16***77 | Washer Group-Window; -Cab | 1 |
| 2G***12 | Window As; (Lh) | 1 |
| 6G***75 | Kit-Handle; (Lh)(Vent Window) | 1 |
156-1854 Washer Gp-Window -Cab
| 15***54 | Washer Group-Window; -Cab | 1 |
| 16***81 | Bottle-Washer | 1 |
| 16***62 | Cover As; (Window Washer) | 1 |
2g-0263 Window Gp -Door, Lh
| 2G***63 | Window Group; -Door, Lh | 1 |
| 2G***18 | Nut | 2 |
| 5K***05 | Nut-Barrel; (6-32-Thd) | 2 |
8w-6212 Window Gp -Door, Rh
| 2V***31 | Catch | 1 |
| 3V***96 | Lock As-Window | 1 |
| 4V***43 | Stop | 1 |
8w-6211 Window Gp-Cab -Door, Rh
| 13***35 | Blade As-Wiper; (650-mm) | 1 |
| 13***88 | Clip | 2 |
| 13***95 | Nozzle As-Washer | 1 |
156-1855 Wiper Gp-Window -Front
| 15***55 | Wiper Group-Window; -Front | 1 |
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
Power Train
6p-5901 Mounting Gp-Torque Converter
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 11 |
| 4H***30 | Seal-O-Ring (532.21mm Id) | 1 |
9w-4119 Actuator Gp-Rotary -Transmission
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 2 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 2 |
| 3E***54 | Ball | 1 |
145-8314 Case & Parts Gp-Planetary
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 22 |
| 14***14 | Case & Parts Group-Planetary | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 4 |
136-3176 Control Ar-Traction
| 13***76 | Control Ar-Traction | 1 |
| 14***03 | Lines Group-Traction Aid | 1 |
| 15***43 | Wiring Group-Sensor; -Wheel Speed | 1 |
3t-1510 Control Gp-Transmission Hyd
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
145-8315 Cover Gp-Shipping -Transmission
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 4 |
| 0T***68 | Bolt,Machine; Tube Mounting And Tube To Junction Block Uoc:Bsv,Bsx | 4 |
| 14***15 | Cover Group-Shipping; -Transmission | 1 |
9d-6130 Differential & Bevel Gear Gp
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 12 |
| 10***31 | Seal As | 1 |
| 10***84 | Cage-Bearing | 1 |
6g-7560 Differential Gp
| 10***58 | Nut; (2-1/8-Thd) | 4 |
| 2K***37 | Nut (National Fine); (3/4-16-Thd) | 8 |
| 3D***09 | Dowel (.625" Long) | 8 |
132-5447 Filter Gp-Oil -Power Train
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***47 | Filter Group-Oil; -Hydraulic-Power Train | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
8x-9981 Drive Gp-Final
| 0L***78 | Bolt,Machine Governor And Decelerator Control | 70 |
| 10***29 | Hub | 2 |
| 14***67 | Gear-Sun; (20-Teeth) | 2 |
7d-2850 Drive Gp-Final
| 03***57 | Bolt; --To Reverse Shaft Bearing Retainer & Forward Shaft Bearing Retainer | 8 |
| 10***29 | Hub | 2 |
| 12***21 | Plug-Magnetic; (Engine Oil Pan Drain) | 2 |
9g-9625 Gear Gp-Transfer -Input
| 03***60 | Cup-Roller Bearing | 2 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 10 |
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 2 |
2g-0627 Housing As-Rear Axle
| 2G***27 | Housing As-Rear Axle | 1 |
| 5J***04 | Boss; (3/8-16-Thd) | 4 |
| 8F***36 | Lug -Weld To Push Frame Strut; (3/8-16x0.75-In) | 12 |
9d-6140 Housing Gp-Rear Axle
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 1D***14 | Bolt--Front Support To Frame | 8 |
| 1D***23 | Bolt 215.9 mm(8.5 In.) Long; Bolt Head To Cylinder Block | 2 |
198-5950 Housing Gp-Rear Axle
| 19***50 | Housing Group-Rear Axle | 1 |
| 2D***45 | Stud 6.63 cm(2.609 In.) Long | 8 |
| 2G***27 | Housing As-Rear Axle | 1 |
142-5743 Lines Gp-Power Train Cooler
| 10***57 | Elbow | 1 |
| 13***11 | Hose As | 1 |
| 14***43 | Lines Group-Power Train Cooler | 1 |
135-9412 Lines Gp-Power Train Oil
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 1 |
| 13***47 | Filter Group-Oil; -Hydraulic-Power Train | 1 |
| 13***58 | Tube As | 1 |
144-5325 Lines Gp-Torque Converter
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 12***96 | Hose As-Orfs | 1 |
| 12***52 | Valve Group-Lockup Clutch & Sol; -Torque Converter | 1 |
141-1903 Lines Gp-Traction Aid
| 14***32 | Hose As | 1 |
| 14***03 | Lines Group-Traction Aid | 1 |
| 2T***88 | Hose As | 2 |
117-3915 Motor Gp-Electric -Engine Prelubrication-Sec Steering, Brake Release
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 2 |
| 7X***08 | Washer-Hard; (10.2x16x2-mm Thk) | 2 |
9g-9628 Planetary Gp-Transmission
| 06***11 | Ring-Retaining | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 8 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 3 |
131-3746 Power Train Ar
| 13***46 | Power Train Ar | 1 |
| 13***06 | Guard Group-Drive Shaft | 1 |
| 14***07 | Transmission Ar | 1 |
111-6841 Pump Gp-Gear -Transmission Charge, Scavenge
| 11***29 | Gear-Oil Pump Drive; (56-Teeth) | 1 |
| 11***41 | Pump Group-Gear; -Transmission Charge, Scavenge | 2 |
| 11***90 | Gasket | 1 |
111-6842 Pump & Drive Gp-Gear -Transmission Charge, Scavenge
| 11***65 | Body As-Oil Pump | 1 |
| 11***42 | Pump Group-Gear; (Transmission Charge, Scavenge)(Powertrain Scavenge & Charging) | 1 |
| 11***56 | Gear As-Oil Pump; (8-Teeth) | 1 |
143-2136 Rim Gp
| 14***36 | Rim Group | 1 |
| 3D***45 | Flange | 2 |
| 6G***31 | Ring-Lock | 1 |
143-2137 Rim Gp
| 14***37 | Rim Group | 1 |
| 2A***13 | Rim As | 1 |
| 3D***45 | Flange | 2 |
7d-2840 Rim Gp-Demountable
| 3D***58 | "O" Ring | 6 |
| 5D***61 | Nut-Sealing; (0.482-26-Thd) | 1 |
| 6G***85 | Valve Group-Tire | 2 |
9d-1875 Rim Gp-Demountable
| 14***36 | Rim Group | 6 |
| 2D***08 | Grommmet | 1 |
| 2D***09 | Locknut; (11/16-16-Thd) | 1 |
114-9220 Rim Gp-Single
| 11***20 | Rim Group-Single | 1 |
| 14***37 | Rim Group | 1 |
| 2D***08 | Grommmet | 1 |
9d-3520 Shaft Gp-Drive -Main
| 15***08 | Slip Joint Group | 1 |
| 9D***20 | Shaft Group-Drive; -Main | 1 |
| 9V***11 | Bolt-12 Point Head; (1/2-20x2.25-In) | 8 |
157-2008 Slip Joint Gp
| 15***08 | Slip Joint Group | 1 |
| 15***09 | Slip Joint Group | 1 |
| 15***10 | Slip Joint Group | 1 |
157-2010 Slip Joint Gp
| 15***10 | Slip Joint Group | 1 |
| 15***11 | Tube & Yoke As | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
157-2009 Slip Joint Gp
| 15***09 | Slip Joint Group | 1 |
| 3H***22 | Grease Nipple (Service Replacement Only) | 1 |
| 8W***12 | Spider & Bearing Group | 2 |
172-7634 Slip Joint Gp
| 17***34 | Slip Joint Group | 1 |
| 17***35 | Tube & Yoke As | 1 |
| 17***38 | Seal | 1 |
136-0478 Tire & Rim Gp
| 13***78 | Tire & Rim Group | 1 |
| 14***37 | Rim Group | 1 |
| 2D***08 | Grommmet | 1 |
142-5742 Torque Converter Ar
| 10***68 | Torque Converter Group | 1 |
| 11***42 | Pump Group-Gear; (Transmission Charge, Scavenge)(Powertrain Scavenge & Charging) | 1 |
| 14***79 | Sensor Group-Temperature | 1 |
108-1868 Torque Converter Gp
| 03***21 | Bolt-Allen Hd; (3/8unc X 1) | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 13 |
| 10***03 | Gauge-Sight; (Hydraulic Oil Level) | 2 |
1t-1213 Torque Converter Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 44 |
| 13***02 | Seal-Lip-Type | 1 |
1t-2046 Torque Converter Gp
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 6 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 44 |
| 13***02 | Seal-Lip-Type | 1 |
145-7407 Transmission Ar
| 14***07 | Transmission Ar | 1 |
| 14***14 | Case & Parts Group-Planetary | 1 |
| 14***15 | Cover Group-Shipping; -Transmission | 1 |
3t-1511 Valve Gp-Transmission Control
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 1 |
| 1D***41 | Bolt 3.00 In.(7.62 cm) Long | 12 |
| 1F***11 | Bolt 3.50 In. (8.89 cm) Long | 1 |
128-2352 Valve Gp-Lockup Clutch & Sol
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 6 |
| 12***52 | Valve Group-Lockup Clutch & Sol; -Torque Converter | 1 |
| 12***80 | Stop | 1 |
3t-1513 Valve Gp-Pressure Control -Clutch Oil Flow
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 1 |
| 16***78 | Body-Load Piston | 7 |
| 1S***36 | Retainer | 1 |
8p-1471 Valve Gp-Relief
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 14***46 | Plug-Pipe | 1 |
| 1L***62 | Ring-Retaining | 1 |
3t-1512 Valve Gp-Selector & Press Cont -Transmission
| 03***30 | Bolt-Self Locking; (5/16unc X 3/4) | 1 |
| 12***33 | Spring As | 2 |
| 13***45 | Pin-Spring | 1 |
9g-9988 Valve Gp-Solenoid
| 12***48 | Kit-Seal; (Solenoid Valve) | 0 |
| 15***84 | Locknut; (Special) (5/8-18 Thd) | 1 |
| 16***43 | Washer-Identification; (16.8x38.1x.5mm Thk) | 1 |
144-6292 Valve Gp-Solenoid
| 10***83 | Kit-Seal; (Solenoid Valve) | 1 |
| 10***11 | Cartridge As | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
3t-0062 Valve Gp-Solenoid
| 11***03 | Seal-O-Ring | 1 |
| 13***34 | Screen As; (Traction Control Valve) | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
193-8559 Valve Gp-Solenoid
| 10***83 | Kit-Seal; (Solenoid Valve) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***11 | Cartridge As | 1 |
7x-1120 Valve Gp-Solenoid
| 10***83 | Kit-Seal; (Solenoid Valve) | 1 |
| 10***70 | Locknut; (1/4-20-Thd) | 1 |
| 4B***76 | Washer Generator Line Leads (Use As Required) | 1 |
9g-9208 Valve Gp-Traction Control
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 10 |
137-6821 Wheel Ar-Final Drive & Brake
| 0L***69 | Bolt (5/8-11 Thd X 3.750 In Long | 35 |
| 0L***78 | Bolt,Machine Governor And Decelerator Control | 35 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
146-8048 Wheel Ar-Final Drive & Brake
| 14***48 | Wheel Ar-Final Drive & Brake | 1 |
| 7D***10 | Wheel Group-Rear | 1 |
| 7D***40 | Rim Group-Demountable | 1 |
7d-2810 Wheel Gp-Rear
| 10***20 | Housing-Axle | 2 |
| 10***38 | Retainer | 2 |
| 10***12 | Pin-Retaining | 4 |
8x-9972 Wheel Gp-Rear
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 20 |
| 10***20 | Housing-Axle | 2 |
| 10***38 | Retainer | 2 |
Service Equipment And Supplies
9g-9288 Cap Gp-Protection -Hydraulic Tank
| 13***76 | Film-Stripe; (130-cm) | 0 |
| 13***77 | Film-Stripe; (411-cm) | 0 |
| 9G***88 | Protection Cover Group; -Hydraulic Tank-Steering Tank Fill Cap-Hydraulic Tank Fill Cap | 1 |
5t-6942 Cap Gp-Protection
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
| 2J***61 | Ring-Retaining | 1 |
140-0037 Film Gp
| 12***28 | Film-Notice; (Radio) | 1 |
| 13***96 | Film-Instruction; (Retarding Guidelines)(769d Only) | 1 |
| 13***97 | Film-Instruction; (Retarding Guidelines)(771d Only) | 1 |
133-9496 Film Gp
| 12***94 | Film-Stripe; (773d) | 1 |
| 12***95 | Film-Stripe; (773d) | 1 |
| 13***02 | Film-Stripe | 1 |
140-0104 Film Gp-Cab -German
| 13***12 | Film-Notice; (Radio) | 1 |
| 13***46 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***38 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0111 Film Gp-Cab -Swedish
| 13***21 | Tag-Warning; (Shipping Brackets)(Shipping Brackets) | 1 |
| 14***11 | Film Group-Cab; -Swedish | 1 |
| 14***16 | Film-Instruction; (Retarding Guidelines)(769d Only) | 1 |
140-0109 Film Gp-Cab -Arabic
| 13***16 | Film-Notice; (Radio) | 1 |
| 13***51 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***43 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0107 Film Gp-Cab -Greek
| 13***15 | Film-Notice; (Radio) | 1 |
| 13***49 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***41 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0102 Film Gp-Cab -Spanish
| 13***10 | Film-Notice; (Radio) | 1 |
| 13***44 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***36 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0105 Film Gp-Cab -Italian
| 13***13 | Film-Notice; (Radio) | 1 |
| 13***47 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***39 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0101 Film Gp-Cab -French
| 13***09 | Film-Notice; (Radio) | 1 |
| 13***43 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***35 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0103 Film Gp-Cab -Portuguese
| 13***11 | Film-Notice; (Radio) | 1 |
| 13***45 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***37 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0106 Film Gp-Cab -Danish
| 13***14 | Film-Notice; (Radio) | 1 |
| 13***48 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***40 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0108 Film Gp-Cab -Dutch
| 13***37 | Film-Notice; (Radio)(Radio) | 1 |
| 13***50 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***37 | Film-Instruction; (Retarding Guidelines) | 1 |
185-3550 Film Gp-Cab -Finnish
| 11***88 | Film; (Identification) (Fuel Filter) (On Secondary Fuel Filter) | 2 |
| 12***71 | Plate-Warning-Rops/Fops | 1 |
| 14***37 | Film Group | 1 |
140-0110 Film Gp-Cab -Japanese
| 13***18 | Film-Notice; (Radio) | 1 |
| 13***52 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***44 | Film-Instruction; (Retarding Guidelines) | 1 |
137-6403 Film Gp-Cab
| 13***08 | Film-Notice; (Radio) | 1 |
| 13***42 | Film-Instruction; (Retarding Guidelines) | 1 |
| 13***34 | Film-Instruction; (Retarding Guidelines) | 1 |
185-1668 Film Gp-Cab -Norwegian
| 13***21 | Tag-Warning; (Shipping Brackets)(Shipping Brackets) | 1 |
| 14***36 | Film-Instruction; (Retarding Guidelines) | 1 |
| 14***37 | Film-Instruction; (Retarding Guidelines) | 1 |
140-0133 Plate & Film Gp -Swedish
| 10***08 | Film-Warning; (Jump Start, Read Omm) | 1 |
| 13***42 | Film-Instruction; (Hydraulic Accumulator) | 2 |
| 14***33 | Plate & Film Group; -Swedish | 1 |
140-0131 Plate & Film Gp -Arabic
| 10***28 | Film-Instruction; (Hydraulic Accumulator)(Japanese) | 2 |
| 10***45 | Film-Warning; (Unit Injector) | 4 |
| 11***64 | Film-Information; (Engine Oil) | 1 |
140-0129 Plate & Film Gp -Greek
| 10***44 | Film-Warning; (Elec Shock Hazard, Unit Inj) | 4 |
| 11***60 | Film-Information; (Engine Oil) | 1 |
| 14***08 | Film Group-Cab; -Dutch | 1 |
140-0125 Plate & Film Gp -Portuguese
| 10***40 | Film-Warning; (Elec Shock Hazard, Unit Inj) | 4 |
| 11***62 | Film-Information; (Engine Oil) | 1 |
| 14***04 | Film Group-Cab; -German | 1 |
185-1665 Plate & Film Gp -Norwegian
| 10***09 | Film-Warning; (Jumper Cables) | 1 |
| 12***15 | Film-Warning | 4 |
| 13***43 | Film-Instruction; (Hydraulic Accumulator)(Replaces 8t***76) | 2 |
140-0123 Plate & Film Gp -French
| 10***38 | Film-Warning; (Unit Injector) | 4 |
| 11***68 | Film-Information; (Engine Oil) | 1 |
| 14***02 | Film Group-Cab; -Spanish | 1 |
136-1814 Plate & Film Gp
| 10***37 | Film-Warning; (Electrical Shock Hazard) | 4 |
| 11***61 | Film-Information; (Engine Oil) | 1 |
| 13***14 | Plate & Film Group | 1 |
140-0126 Plate & Film Gp -German
| 10***41 | Film-Warning; (Elec Shock Hazard, Unit Inj) | 4 |
| 11***65 | Film-Information; (Engine Oil) | 1 |
| 14***05 | Film Group-Cab; -Italian | 1 |
140-0130 Plate & Film Gp -Dutch
| 10***23 | Film-Warning; (High Pressure Cylinder) | 2 |
| 10***23 | Film-Warning; (High Pressure Cylinder) | 4 |
| 10***25 | Film-Warning; (High Pressure Cylinder) | 2 |
140-0127 Plate & Film Gp -Italian
| 10***42 | Film-Warning; (Elec Shock Hazard, Danish) | 4 |
| 11***70 | Film-Information; (Engine Oil) | 1 |
| 14***06 | Film Group-Cab; -Danish | 1 |
140-0124 Plate & Film Gp -Spanish
| 10***39 | Film-Warning; (Elec Shock Hazard, Unit Inj) | 4 |
| 11***66 | Film-Information; (Engine Oil) | 1 |
| 14***03 | Film Group-Cab; -Portuguese | 1 |
185-3548 Plate & Film Gp -Finnish
| 18***48 | Plate & Film Group; -Finnish | 1 |
140-0128 Plate & Film Gp -Danish
| 10***43 | Film-Warning; (Unit Injector) | 4 |
| 11***63 | Film-Information; (Engine Oil) | 1 |
| 14***07 | Film Group-Cab; -Greek | 1 |
140-0132 Plate & Film Gp -Japanese
| 10***99 | Film-Warning; (High Pressure Cylinder)(High Pressure Cylinder) | 4 |
| 10***23 | Film-Instruction; (Hydraulic Accumulator) | 2 |
| 10***48 | Film-Warning; (Elec Shock Hazard, Unit Inj) | 4 |
131-0358 Plate-Warning -Stopping
| 13***58 | Plate-Warning; -Stopping | 1 |
Steering System
136-1804 Cylinder & Mtg Gp-Steering
| 10***57 | Cylinder Group-Steering | 2 |
| 13***04 | Cylinder & Mtg Group-Steering | 1 |
| 1B***45 | Nut-Slotted | 4 |
105-3357 Cylinder Gp-Steering
| 10***57 | Cylinder Group-Steering | 1 |
| 10***58 | Cylinder As | 1 |
| 10***60 | Rod As | 1 |
173-0159 Filter Gp-Oil -Steering Pump Case Drain
| 10***36 | Seal-O-Ring; (49.28mm Id) | 1 |
| 12***13 | Filter-Oil; (Ultra High Efficiency)(Hydraulic, Pilot) | 1 |
| 17***59 | Filter Group-Oil; -Ultra High Efficiency-Hydraulic Tank | 1 |
135-9417 Lines Gp-Secondary Steering
| 11***16 | Valve & Mounting Group; -Secondary Steering | 1 |
| 12***55 | Pump & Motor Group-Sec Steering | 1 |
| 13***84 | Clip | 5 |
194-1100 Lines Gp-Secondary Steering
| 13***84 | Clip | 5 |
| 13***28 | Hose As | 1 |
| 16***72 | Hose As | 1 |
135-9416 Lines Gp-Steering
| 10***93 | Stud-Taperlock; (3/8-16x2.36-In)(3/8-16x60 Thd) | 2 |
| 12***27 | Valve Group-Check & Relief; -Steering | 1 |
| 13***00 | Tube As | 1 |
194-1099 Lines Gp-Steering
| 10***93 | Stud-Taperlock; (3/8-16x2.36-In)(3/8-16x60 Thd) | 2 |
| 13***00 | Tube As | 1 |
| 13***01 | Tube As | 1 |
9d-6280 Link Gp-Steering
| 12***05 | Clamp As | 2 |
| 13***63 | Arm-Center | 1 |
| 13***64 | Arm-Steering | 2 |
128-4855 Pump & Motor Gp-Sec Steering
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 11***68 | Gasket | 1 |
| 12***55 | Pump & Motor Group-Sec Steering | 1 |
154-3023 Pump Gp-Gear -Sec Steering, Brake Release
| 09***95 | Pin, Dowel | 8 |
| 13***35 | Seal-Shaft | 1 |
| 14***99 | Flange | 1 |
192-4286 Pump Gp-Metering -Hmu
| 14***61 | Race-Bearing | 2 |
| 19***86 | Pump Group-Metering; -Hmu | 1 |
| 25***12 | Kit-Seal; (Hmu Steering) | 1 |
129-2372 Pump Gp-Metering -Steering
| 09***66 | Bolt; (M8x1.25x75-mm) | 7 |
| 11***06 | Plug | 2 |
| 11***08 | Spring | 2 |
179-1258 Steering Column Gp
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***89 | Adapter | 2 |
210-6592 Steering Column Gp
| 18***34 | Kit-Column; (Core) | 1 |
| 18***35 | Nut; (7/8-20-Thd) | 1 |
| 18***37 | Kit-Universal Joint; (Steering Column) | 1 |
340-1167 Steering Column Gp-Adjustable
| 12***72 | Pump Group-Metering; -Steering | 1 |
| 13***70 | Wheel-Steering | 1 |
| 13***39 | Grommet; (17.5 Thk)(3 Hole) | 1 |
162-4227 Steering Gear Gp
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***39 | Grommet; (17.5 Thk)(3 Hole) | 1 |
170-8018 Tank & Filter Gp-Steering
| 12***07 | Tank & Filter Group-Steering | 1 |
| 17***18 | Tank & Filter Group-Steering | 1 |
| 5C***65 | Bolt-Plt; (1/2unc X 1 1/8) | 6 |
120-6107 Tank & Filter Gp-Steering
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 41 |
136-3328 Tank Gp-Hydraulic
| 13***28 | Tank Group-Hydraulic | 1 |
| 17***18 | Tank & Filter Group-Steering | 1 |
| 5C***65 | Bolt-Plt; (1/2unc X 1 1/8) | 6 |
169-9520 Tank Gp-Hydraulic
| 16***20 | Tank Group-Hydraulic | 1 |
| 7T***45 | Manifold-Solenoid Valve | 1 |
| 8T***92 | Valve Group-Solenoid; (Ride Control) | 1 |
110-1216 Valve & Mounting Gp -Secondary Steering
| 10***10 | Valve-Check; (Steering) | 2 |
| 10***11 | Plug; (5/16-12 Thd) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
175-7050 Valve Gp-Check & Relief -Steering
| 17***50 | Valve Group-Check & Relief; -Steering Lines Pressure | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 5P***99 | Ring-To Clutch Piston Pins | 1 |
128-6027 Valve Gp-Check & Relief -Steering
| 10***10 | Valve-Check; (Steering) | 2 |
| 10***11 | Plug; (5/16-12 Thd) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
114-1267 Valve Gp-Pressure Reducing -Steering
| 11***67 | Valve Group-Pressure Reducing; -Steering-Pilot | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 5P***99 | Ring-To Clutch Piston Pins | 1 |
252-8039 Valve Gp-Pressure Reducing
| 25***39 | Valve Group-Pressure Reducing; -Secondary | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
9t-9194 Valve Gp-Relief -Secondary Steering
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***71 | Plate | 1 |
4t-2742 Valve Gp-Relief -Secondary Steering
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***41 | Spring | 1 |
| 4T***42 | Valve Group-Relief; -Secondary Steering | 1 |
108-2185 Valve Gp-Relief -Primary Steering
| 10***85 | Valve Group-Relief; -Primary-Primary Steering | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***42 | Spring | 1 |
128-6148 Valve Gp-Relief -Primary Steering
| 10***70 | Locknut; (1/4-20-Thd) | 1 |
| 12***48 | Valve Group-Relief; -Primary Steering | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
8t-8692 Valve Gp-Solenoid
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
| 15***38 | Cartridge Assem. | 1 |
| 18***72 | Coil As | 1 |
152-8339 Valve Gp-Solenoid
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 15***38 | Cartridge Assem. | 1 |
| 15***39 | Valve Group-Solenoid | 1 |
152-8340 Valve Gp-Solenoid
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 12 |
| 13***27 | Spindle | 2 |
| 13***29 | Seal Group-Duo-Cone; (Front Wheel) | 2 |
6g-8241 Wheel Gp-Front
| 07***41 | Seal; (30.3mm Od) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***74 | Solenoid As-Proportional; (Pilot Control Actuator) | 1 |
773D serial number reference
The PIN plate is riveted to the left front frame rail, low down near the front axle and below the operator's cab - stand at the front left corner of the truck and look down along the frame to find it. Read the first three characters of the 8-character machine serial number (or the last 8 of a 17-character PIN) as the prefix, which identifies the model/production series; the remaining five digits are the sequential unit number within that prefix.
| Prefix | Identifies | Notes |
|---|---|---|
| 7ER | 773D off-highway truck, early production series | Runs from 7ER00001-UP, with a machine-arrangement break at 7ER00380/7ER00381. Fitted with the Cat 3412E engine. Seen on 1996 through 1998 model-year trucks in dealer and auction records. |
| 7CS | 773D off-highway truck, later production series | Continuation prefix after 7ER, running 7CS00001-UP. Fitted with the Cat 3412E engine (approx. 485 kW / 650 hp gross). Seen on 1999 through 2001 model-year trucks in dealer and auction records. |
Frequently asked questions
What engine does the Caterpillar 773D use?
The 773D runs the Cat 3412E, a 12-cylinder, 27 L, turbocharged-and-aftercooled diesel with HEUI (hydraulically actuated, electronically controlled) fuel injection. Gross power is rated at 509 kW (682.6 hp) at 2000 rpm, with net/flywheel output in the 480-485 kW (644-650 hp) range depending on the rating standard used.
What is the operating weight of the Caterpillar 773D?
Empty operating weight is about 39,500 kg (87,082 lb). Loaded gross weight runs near 99,300 kg (219,000 lb), giving a rated payload capacity around 43,600 kg (96,260 lb). Exact figures shift with body style, tire choice and counterweight options.
What replaced the Caterpillar 773D?
The Cat 773E succeeded the 773D, entering production around 2002 and carrying the 3412E HEUI engine and shared-TDTO powertrain forward with further refinement. The 773D itself had replaced the mechanically-injected 773B around 1996.
What 773D owners discuss
What's the main engine/fuel-system issue owners and mechanics flag on the 773D?
The 773D runs the Cat 3412E, a HEUI (hydraulic electronic unit injector) diesel. Early-build trucks used first-generation 'primed' injector squirters, a known weak point - multiple sets could fail before the fuel system settled in. Trucks built later in the D-series run, roughly the 2003-and-newer window, switched to a revised 'non-primed' squirter design that delivers fuel in a single event instead of two stages. Field reports on the later squirters describe them reaching well over 20,000 hours on a 250-hour service interval when run on the correct engine oil. When shopping a used unit, ask which squirter generation is fitted and what the injector service history looks like.
How does the transmission and torque converter behave, and what do mechanics watch for?
Transmission and torque converter run on separate oil sumps, so a converter problem doesn't automatically contaminate the transmission oil and vice versa. The converter is a lockup type: it stays in converter drive at low speed for cushioned shifting, then locks up mechanically once the truck reaches roughly 6.9 km/h (4.3 mph), sending more power straight to the wheels and cutting heat and fuel burn. The lockup clutch releases and reapplies quickly during shifts to limit torque windup. Owners report the main service point is simply keeping the correct transmission drive train oil topped up in the transmission, converter, and brake/hoist circuits; low or wrong-spec oil is the most common cause of premature wear.
What wear pattern shows up on the suspension struts, and how is it serviced?
Front and rear suspension uses nitrogen-over-oil struts rather than leaf or coil springs. Oil quantity sets the damping rate; nitrogen charge sets ride height, both loaded and empty. The recurring complaint on these struts is leak-down: a strut that has lost ride height or rides harsh and bouncy usually just needs a recharge, not a rebuild, if there is no external leak. Techs are emphatic that the charging procedure must fully purge air before introducing nitrogen, since mixing the two inside a pressurized strut is a real explosion risk. Charge should always be checked with the truck body empty and on level ground. Have your dealer verify strut charge pressure and purge procedure before servicing - this is a high-pressure, safety-critical job.
What do mechanics say about the brake system and its maintenance behavior?
Braking is oil-cooled, multi-disc, combining service, secondary, parking, and retarding functions in one assembly at each wheel. The oil-film design is built to be adjustment-free, so routine brake adjustment isn't the maintenance item it would be on a dry-disc truck. On long grades the engine retards against compression, keeping fuel burn down on descents. The practical takeaway from operators: watch the brake oil temperature gauge and the rear wear indicator rather than waiting for pedal feel to change, since disc wear on an oil-cooled system isn't obvious to the driver until it's advanced. Have your dealer verify brake wear indicator readings and oil temperature before returning the truck to service if either has been flagged.
What steering and electrical/sensor issues come up most in the field?
Steering complaints are one of the most repeated topics: operators describe a 773D with worn steering linkage as feeling loose and slow to respond. Mechanics usually trace this to worn tie rods, drag link, or ball joints in the linkage, or to low hydraulic fluid or pressure in the steering circuit reducing responsiveness. On the electrical side, reported faults tend to be connector-level rather than true component failure - moisture or oil intrusion into a sensor connector, for example on injector or pressure wiring, throws fault codes that look like a bad sensor but clear once the connector and terminals are cleaned and resealed. Loose battery cable connections have also been flagged as shipped-loose on some trucks, worth a physical check before chasing a charging-system fault. Have your dealer verify steering linkage play and hydraulic pressure - this is a safety-critical system.
What tire and drivetrain wear patterns are typical, and how do operators reduce them?
As a rigid-frame truck the 773D has no track undercarriage, so the equivalent wear items are tires, brakes, and drivetrain. Tires typically run in the 21.00-35 size range, in bias or radial construction depending on how the truck is set up. Operator consensus is that engaging the traction control system as soon as wheel slip starts, instead of letting the wheel spin, meaningfully reduces tire wear. The other big driver of accelerated tire, brake, and drivetrain wear is running the truck over its rated gross machine weight; payload discipline is treated by operators and dealers as the single biggest lever on component life.
What should a buyer check on a used 773D before purchase?
Pull the hour meter and ask which HEUI injector squirter generation is fitted, early primed versus the later non-primed design, since that is tied to a documented reliability jump. Check for leaks at the engine, transmission and converter, hydraulic circuits (steering and hoist), and suspension strut seals; no visible leaks and steady oil levels are treated as a good sign. Grab the steering wheel and check for play in the linkage, and cycle it to feel for sponginess that points to low steering pressure. Check the brake oil temperature gauge and rear wear indicator rather than relying on pedal feel. Check suspension strut ride height with the body empty on level ground; a sagging strut usually means a recharge is overdue. Walk the frame and body liners for cracking or repair welds, since haul-road impact loading is the main structural fatigue driver on this class of truck. Have your dealer verify the hydraulic and brake systems with a full inspection before purchase - these are safety-critical systems on a truck this size.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 773D part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.