Caterpillarexcavatorfront shovel
Caterpillar 5090B
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 5090B is a large hydraulic front shovel built for mining and quarry face loading, not a general-purpose digging excavator. It carries a fixed bottom-dump bucket on a parallelogram-type front linkage that keeps the bucket bottom parallel to the ground through the dig stroke, giving fast penetration and a clean floor pass, then dumps by opening the bucket bottom over the haul truck rather than curling and swinging a backhoe-style bucket. Power comes from Caterpillar's 3456 ATAAC inline-six diesel, a 15.8 L, turbocharged, air-to-air aftercooled engine rated 382 kW (513 hp) net at 1800 rpm. Operating weight runs around 91,600 kg (201,900 lb) in standard configuration, with some build configurations landing closer to 87,500-87,700 kg (193,000-193,400 lb) depending on bucket and counterweight choice. Caterpillar built the 5090B from about 2002 to 2004 as the direct successor to the 5080 shovel, offering it across multiple factory build series with a range of bucket sizes from about 4.6 to 5.7 m³ (6.0 to 7.5 yd³), sized to load haul trucks in the 36-63 tonne (40-70 ton) class.
Against the 5080 it replaced, the 5090B added roughly 20 percent more engine horsepower, higher hydraulic flow, about 16 percent more swing torque, and greater drawbar pull, plus the ability to run larger buckets, all built around a three-pump closed-center load-sensing hydraulic system (Cat's PPPC design) with an independent, priority swing circuit for stronger acceleration and easier multi-function control. The 5090B shares its 3456 ATAAC engine and main hydraulic pump architecture with Caterpillar's 385B excavator of the same era, which keeps parts cross-application reasonably strong in the used market. Caterpillar wound the entire 5000-series shovel line down by the mid-2000s: a 2003 agreement to sell shovel intellectual property to Terex named only the larger 5110B, 5130B, and 5230B models, that deal collapsed in early 2004, and Caterpillar did not return to large hydraulic mining shovels as a standalone product line until years later under a different model family. No confirmed direct successor to the 5090B exists in factory literature. On today's used and parts market, surviving 5090B units draw interest from quarry and aggregate operators wanting a simpler, pre-emissions-era engine and control system, and demand centers on the shared 3456 engine parts pool, swing- and final-drive rebuild components, and undercarriage wear parts common to this machine class.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 5090B specifications
Engine
| Engine model | Cat 3456 ATAAC, 6-cylinder turbocharged air-to-air aftercooled diesel with electronic unit injection and ADEM II electronic control |
| Net power | 382 kW (513 hp) @ 1800 rpm |
| Displacement | 15.8 L (964 in³) |
| Bore x stroke | 140 mm x 171 mm (5.51 in x 6.73 in) |
| Emissions | Engine family for this production run (2002-2004) certified to EPA Tier 2 / EU Stage II nonroad standards |
Weights
| Operating weight (standard front-shovel configuration) | 91,600 kg (201,900 lb) |
| Operating weight, alternate configurations | Approximately 87,500-87,700 kg (192,900-193,400 lb) reported on some listings; varies by bucket, counterweight and undercarriage option |
| Counterweight | Fabricated counterweight, 11.6 t (25,600 lb) |
Dimensions
| Overall length | 13.77 m (45 ft 2 in) |
| Overall width | 3.51 m (11 ft 6 in) |
| Overall height | 5.31 m (17 ft 5 in) |
| Boom length | 4.6 m (15 ft 1 in) |
| Stick length | 3.4 m (11 ft 5 in) |
| Standard track shoe width | 650 mm (26 in) |
| Ground clearance | 850 mm (2 ft 9 in) |
| Cab riser, standard | 870 mm (34 in) |
Performance
| Max reach at ground level | 9.89-10.09 m (32.45-33.1 ft); varies by configuration/source |
| Max loading (dump) height | 7.44 m (24.41 ft) |
| Travel speed, high range | 4.5 km/h (2.8 mph) |
| Travel speed, low range | 2.8 km/h (1.75 mph) |
| Swing speed | 6.2 rpm |
| Swing torque | 260 kN·m (191,770 lb-ft), about 16% higher than the prior 5080 model |
| Drawbar pull | 592 kN (133,000 lb) |
Forces
| Bucket digging (breakout) force | 468-538 kN across the factory bucket options; varies by bucket size and configuration |
Service capacities (summary)
| Fuel tank | 1240 L (328 gal) |
| Engine oil | 80 L (21.1 gal) |
| Hydraulic system | 995 L (263 gal) |
| Cooling system | 101 L (26.7 gal) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
5090B fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 80 L (21.1 US gal) full service refill; running/dipstick range documented lower, around 65 L (17.2 US gal) | Cat DEO (Diesel Engine Oil). SAE 10W-30 multigrade is the preferred year-round grade for the 3456/C18 engine across roughly -18°C to 40°C (0°F to 104°F). SAE 15W-40 is the common alternate multigrade. In colder ambient ranges step down toward 0W-40 or 5W-40; for hot, steady climates single-grade SAE 30 or SAE 40 is acceptable. Match the exact grade to the machine's Lubricant Viscosities table for local ambient temperature. |
| Cooling system | 101 L (26.7 US gal) | Cat ELC (Extended Life Coolant), glycol-based, organic acid technology, no supplemental coolant additive needed through its service life. Cat DEAC (conventional heavy-duty coolant/antifreeze) is the alternate, but needs periodic SCA additions. Do not mix ELC with conventional coolant. |
| Fuel tank | 1240 L (328 US gal) | Diesel fuel meeting the applicable ASTM D975 / EN590 grade for the operating season; use the lower-cloud-point winter-grade fuel in cold ambient conditions to avoid gelling. |
| Hydraulic system total | 995-996 L (263 US gal), including tank | Cat HYDO Advanced hydraulic oil. Grade selection follows ambient temperature: 10W for normal and cold-weather operation, 30 or 46 grade for sustained hot climates. Cat DEO or Cat TDTO in the matching viscosity can serve as a cross-application fluid where Cat HYDO is unavailable. |
| Hydraulic tank | 810 L (214 US gal) | Same Cat HYDO Advanced fluid and viscosity guidance as the hydraulic system total; the tank capacity is the portion held in the reservoir, the balance is in lines, cylinders and coolers. |
| Final drive (each) | 21 L (5.5 US gal) | Cat TDTO (Transmission/Drive Train Oil), SAE 30 as the standard grade for this duty class. Cat TDTO-TMS (synthetic, wider multigrade range) is the cold-climate alternate where ambient temperature swings are wide. |
| Swing drive | 19 L (5 US gal) | Cat TDTO, same grade guidance as the final drives: SAE 30 standard, Cat TDTO-TMS synthetic for cold-weather service. |
| Pilot/other circuits | Not separately listed; the pilot hydraulic circuit draws from the main hydraulic tank and is included in the hydraulic system total above | Same Cat HYDO Advanced fluid as the main hydraulic system. |
| Grease (spec only) | Spec only, no fixed refill volume, applied per lube point at scheduled intervals | Cat Prime Application Grease or Cat Advanced 3Moly Grease, NLGI 2, extreme-pressure/molybdenum-disulfide fortified, for pin, bushing and bucket-linkage lube points. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 5090B maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
| Every 6,000 h |
|
Servicing the 5090B beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S.O.S sampling on engine oil, hydraulic oil, coolant, and both swing-drive and final-drive oil on a fixed schedule. The roughly 995 L three-pump PPPC hydraulic system is contamination-sensitive, so treat oil cleanliness as pump protection, not just engine care on the 3456 ATAAC. Watch swing-drive and final-drive samples for water or rising metal, an early sign of seal weep before it turns into a visible leak. Face-loading duty cycles push more shock load through the hydraulic circuit than general digging, so shorten sampling intervals in heavy quarry service.
Corrective & Common Repairs
Swing hesitation or drag usually traces to internal leakage in one of the two swing motors or a sticking PPPC control-valve spool, not a worn swing bearing; check pressure and flow at the motor ports first. Final-drive leaks show up at the seal behind the sprocket; swing gearbox leaks show at the output pinion seal, both accelerated by the constant swing-and-dump cycle of face loading. Inspect the parallelogram linkage bushings and bottom-dump latch regularly; repeated bucket-bottom impact against the load wears these faster than a digging bucket's pins.
Overhaul & Rebuild Points
Plan swing-drive and final-drive rebuilds around seal condition and oil-sample metal trend, not a fixed hour count; both drives see heavier duty on a shovel than a comparable excavator since every cycle includes a full swing and a bucket-bottom dump. Inspect boom, stick, and parallelogram linkage box-section welds for fatigue cracking at major overhauls, a known wear point on machines this size after years of face-loading impact. Main hydraulic pump rebuilds on the three-pump PPPC system follow S.O.S metal trends, not calendar time.
Seasonal & Environment Servicing
Cold climates need Cat DEO graded for ambient conditions (10W-30 or Arctic-grade below freezing) and TDTO graded by season in the swing drives and final drives; run winter-grade fuel in the 1240 L tank to limit waxing. Quarry and mining dust loads the ATAAC aftercooler and radiator cores fast, so clean them daily rather than on a fixed interval; a plugged core shows soft power under load before it overheats. Wash accumulated rock fines off the swing gearbox and undercarriage between shifts so seal weep stays visible.
5090B common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1R-0762 | Filter As-Fuel | Fuel system service | Check fitment → |
| 129-0375 | Bowl As-Water Collection | Fuel system service | Check fitment → |
| 133-5673 | Element | Fuel system service | Check fitment → |
| 141-0284 | Kit-Fuel Filter & Waterseparator | Fuel system service | Check fitment → |
| 106-3969 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
5090B fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| 110-0 (flash 61) | High engine coolant temperature warning; coolant temperature has exceeded normal operating range. | Low coolant level, plugged radiator core or debris screen, slipping or failed fan drive, faulty thermostat, or an overloaded engine in hot ambient conditions. | Reduce load and idle down if temperature keeps climbing, check coolant level and radiator/screen for debris, verify fan operation, confirm with a scan tool before returning to work. |
| 111-1 (flash 62) | Low engine coolant level warning; the coolant level switch reads below the safe threshold. | External or internal coolant leak, loose hose clamp or fitting, or a faulty level switch or its wiring. | Inspect hoses, radiator, and water pump for leaks, top off coolant to spec, verify the level switch circuit before restart. |
| 100-1 (flash 46) | Low engine oil pressure warning; oil pressure reading has dropped below the programmed minimum for current rpm. | Low oil level, clogged oil filter, worn oil pump, or a failing oil pressure sensor or its wiring. | Idle down and shut the engine off immediately, check oil level and filter condition, verify actual pressure with a mechanical gauge before restart. |
| 102-3 (flash 25) | Boost/turbocharger outlet pressure sensor signal above the normal voltage range, pointing to an open circuit or short to a high-voltage source. | Damaged sensor wiring or connector, corroded connector pins, or a failed boost pressure sensor. | Inspect sensor connector and harness for damage or corrosion, check sensor supply voltage, replace the sensor if wiring checks out. |
| 110-3 (flash 27) | Engine coolant temperature sensor circuit reading above the normal voltage range; a sensor/wiring fault rather than an actual overheat. | Open circuit, damaged harness, or a failed coolant temperature sensor. | Check sensor wiring and connector, test sensor resistance against spec, replace the sensor or repair the harness as needed. |
| 168-2 (flash 17) | Electrical system (battery) voltage erratic, intermittent, or incorrect at the ECM. | Loose or corroded battery connections, a failing alternator, or a chafed/intermittent harness ground. | Check battery terminals and ground straps, test charging system output, clean or repair connections before clearing the code. |
| 190-8 (flash 34) | Engine speed sensor signal has an abnormal frequency, pulse width, or period; ECM cannot read a clean rpm signal. | Damaged or misaligned speed sensor, metal debris on the sensor tip, or a wiring/connector fault. | Check sensor air gap and mounting, inspect for debris, test wiring continuity, replace the sensor if needed. |
| 94-1 (flash 63) | Low fuel delivery pressure warning; pressure at the fuel pressure sensor is below normal operating range. | Clogged primary or secondary fuel filter, restricted fuel line, or a failing transfer pump. | Check fuel filters and lines for restriction, confirm fuel level, test transfer pump pressure against spec. |
| 254-12 (flash 53) | Electronic control module internal failure; ECM has detected an internal hardware fault. | Internal ECM component failure, often from voltage spikes, moisture intrusion, or age-related wear. | Recheck with a scan tool after reconnecting; if the fault stays active the ECM typically needs dealer-level testing or replacement. |
| 1-5 (flash 71) | Cylinder #1 injector solenoid current below normal; the injector circuit is not drawing expected current. | Open or high-resistance injector wiring, failed injector solenoid, or a loose connector at the valve cover harness. | Check injector wiring and connector for that cylinder, measure solenoid resistance, replace the injector or repair the harness as indicated; the same fault pattern repeats per cylinder as the equivalent code on cylinders two through six. |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
5090B attachments & work tools
Buckets
The 5090B is a dedicated front shovel with a bottom-dump bucket, not a bolt-on general-purpose bucket. Factory bucket options span roughly 4.6-5.7 m³ (6.0-7.5 yd³) across the range, with 5.2 m³ commonly cited as the base/standard capacity - sized to load 40-70 ton haul trucks in 4-5 passes. Bucket is pin-retained directly to the parallelogram front linkage; there is no bolt-on GD/HD/rock bucket line or pin-diameter spec published separately from the shovel arm.
Hydraulic hammers
No hammer pairing is documented for the 5090B in factory or dealer literature. The machine is built as a single-purpose loading shovel around its bottom-dump bucket, not as a multi-tool carrier, so there's no verified Cat hammer class match for this model. Treat any field-fitted breaker as a custom application sized to the 90-tonne-class carrier - confirm structural and hydraulic suitability with a dealer before fitting.
Quick couplers
No quick coupler is offered or documented for the 5090B. The bucket mounts as a fixed, pinned attachment integral to the shovel linkage, consistent with mining/quarry front shovels in this weight class, where coupler-based tool changes aren't used.
Thumbs/grapples
Not documented for this model. As a dedicated bottom-dump-bucket loading shovel, the 5090B doesn't carry thumb or grapple work tools in any factory or dealer material found.
Rippers
Not applicable/documented. Ripper attachments aren't part of the 5090B lineup - ripping duty at this scale is handled by dozer-mounted rippers, not shovel-mounted attachments.
Hydraulic kit notes
Factory hydraulic circuit is a three-pump layout with an independent swing circuit and Cat's Proportional Priority Pressure Compensated (PPPC) valve system, dedicated to boom, stick and bucket functions. No auxiliary medium-pressure or high-flow work-tool circuit is documented, reflecting the machine's role as a single-purpose front shovel rather than a multi-attachment excavator.
All 5090B assemblies by section
Every catalogued assembly group for the Caterpillar 5090B. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
151-6658 Air Cleaner Gp
| 13***47 | U-Bolt | 2 |
| 15***58 | Air Cleaner Group | 1 |
| 17***42 | Bracket As | 1 |
151-6655 Extension Gp-Exhaust
| 13***47 | U-Bolt | 2 |
| 15***55 | Extension Group-Exhaust | 1 |
| 17***42 | Bracket As | 1 |
191-6147 Lines Gp-Air
| 19***47 | Lines Group-Air | 1 |
| 19***23 | Turbocharger Group | 1 |
| 1S***95 | Gasket-Turbocharger To Manifold; Gasket Turbocharger To Manifold | 1 |
127-9039 Lines Gp-Air
| 12***39 | Lines Group-Air | 1 |
| 13***47 | U-Bolt | 2 |
| 17***46 | Bracket As | 1 |
151-6663 Lines Gp-Air
| 11***87 | Bolt; (M6x0.04x10.4-mm)(6mm X 0.04 Thd) | 1 |
| 13***50 | Clamp As-Compressor | 1 |
| 15***63 | Lines Group-Air | 1 |
151-6656 Lines Gp-Air
| 13***47 | U-Bolt | 2 |
| 15***56 | Lines Group-Air | 1 |
| 17***46 | Bracket As | 1 |
114-1904 Lines Gp-Air
| 11***04 | Lines Group-Air | 1 |
| 13***47 | U-Bolt | 2 |
| 17***46 | Bracket As | 1 |
151-6661 Lines Gp-Muffler Drain
| 10***84 | Bolt-Socket Head; (M10x1.5x25-mm) | 6 |
| 15***61 | Lines Group-Muffler Drain | 1 |
| 18***95 | Vent As | 1 |
135-6552 Manifold Gp-Exhaust
| 12***29 | Core As-Fuel Cooler | 1 |
| 13***96 | Washer; (10.2x39.6x2.3-mm Thk) | 4 |
| 13***52 | Manifold Group-Exhaust | 1 |
151-6657 Mounting Gp-Air Cleaner
| 15***57 | Mounting Group-Air Cleaner | 1 |
| 1R***62 | Filter As-Fuel; (Advanced Efficiency)(Secondary) | 2 |
205-6912 Muffler Gp
| 03***36 | Connector-O-Ring | 1 |
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 1 |
| 03***62 | Elbow, Swivel Nut 45 Degrees (-6) | 1 |
194-7923 Turbocharger Gp
| 03***72 | Elbow; (Flared 90 Degree) | 1 |
| 09***86 | Clamp; (Hose) | 1 |
| 13***71 | Filter Group-Water Sep & Fuel; -Primary | 1 |
197-0868 Turbocharger Gp
| 00***64 | End; (Hose) | 2 |
| 03***72 | Elbow; (Flared 90 Degree) | 1 |
| 09***86 | Clamp; (Hose) | 4 |
Basic Engine
133-9907 Adapter Gp-Pump Drive
| 13***06 | Adapter | 1 |
| 13***07 | Adapter Group-Pump Drive; -Remote | 1 |
| 1B***67 | Ball Bearing | 2 |
122-1248 Base Gp-Valve Cover & Inj Harn
| 10***18 | Clip | 3 |
| 10***19 | Clip | 3 |
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
185-9699 Camshaft Gp
| 10***89 | Cover | 1 |
| 11***36 | Screw-Flat Head; (5/16-18x0.875-In) | 3 |
| 18***49 | Camshaft | 1 |
109-7423 Cover Gp-Cylinder Block
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***23 | Cover Group-Cylinder Block | 1 |
| 10***24 | Cover-Cylinder Block | 1 |
107-6736 Cover Gp-Cylinder Block
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 10***36 | Cover Group-Cylinder Block; -Remote | 1 |
| 4N***99 | Gasket; (Oil Drain) | 1 |
150-4278 Cover Gp-Front Housing
| 10***45 | Seal-Accessory Cover | 1 |
| 14***01 | Cover | 1 |
| 14***38 | Screw-Button Head | 3 |
235-8025 Cover Gp-Front Housing
| 11***18 | Cover | 1 |
| 11***19 | Gasket | 1 |
| 1F***58 | Nut-Full; (1/2-13-Thd)(Air Lines) | 3 |
150-3344 Cover Gp-Front Housing
| 11***18 | Cover | 1 |
| 11***19 | Gasket | 1 |
| 15***44 | Cover Group-Front Housing | 1 |
341-6804 Cover Gp-Valve Mechanism
| 11***20 | Seal-O-Ring; (Mid-Liner) | 6 |
| 13***17 | Seal D-Ring | 6 |
| 13***81 | Liner-Cylinder Block | 6 |
150-3135 Cover Gp-Valve Mechanism
| 14***78 | Grommet | 1 |
| 15***57 | Cover-Valve Mech | 1 |
| 15***35 | Cover Group-Valve Mechanism | 1 |
187-1327 Cover Gp-Valve Mechanism
| 13***20 | Crankshaft As | 1 |
| 18***27 | Cover Group-Valve Mechanism | 1 |
| 1W***02 | Gear-Crankshaft; (80-Teeth) | 1 |
187-1326 Cover Gp-Valve Mechanism
| 17***27 | Seal | 1 |
| 17***90 | Fastener As | 6 |
| 18***25 | Cover As-Valve | 1 |
137-7298 Crankshaft Gp
| 10***99 | Plug | 2 |
| 11***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 13***98 | Crankshaft Group | 1 |
202-1255 Cylinder Block As
| 10***99 | Plug | 2 |
| 11***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 14***29 | Seal; (Drainback) | 1 |
249-5631 Cylinder Block Gp
137-8469 Cylinder Block Gp
| 13***69 | Cylinder Block Group | 1 |
| 16***81 | Cap-Crankshaft Bearing | 7 |
| 16***83 | Bolt; (7/8-14x7.5-In) | 14 |
137-8471 Cylinder Block Gp
| 10***99 | Plug | 2 |
| 13***71 | Cylinder Block Group | 1 |
| 14***29 | Seal; (Drainback) | 1 |
202-1254 Cylinder Block Gp
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
243-6741 Cylinder Head As
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
243-0943 Cylinder Head As
| 00***17 | Elbow | 1 |
| 03***78 | Connector-Filtered Fuel To Adapter | 1 |
| 10***25 | Stud; (3/8-16x1.25-In) | 1 |
223-7263 Cylinder Head As
| 12***47 | Guide-Valve; (0.51-mm Os)(Standard) | 0 |
| 12***75 | Guide-Valve; (Standard) | 24 |
| 12***12 | Guide-Valve; (0.13-mm Os)(Standard) | 0 |
183-5296 Cylinder Head Gp
| 10***25 | Stud; (3/8-16x1.25-In) | 1 |
| 10***73 | Fastener Group-Cylinder Head; (Marked X) | 10 |
| 10***18 | Sensor Group-Temperature; (Intake Manifold Air) | 1 |
223-9250 Cylinder Head Gp
| 15***34 | Damper As | 1 |
| 21***77 | Adapter; (Spun Steel) | 1 |
| 22***50 | Cylinder Head Group | 1 |
135-6531 Cylinder Head Gp
| 10***29 | Seal-Valve Stem | 24 |
| 13***31 | Cylinder Head Group | 1 |
| 15***23 | Valve; (Inlet) | 12 |
176-9918 Cylinder Head Gp
| 15***23 | Valve; (Inlet) | 12 |
| 15***24 | Valve; (Exhaust) | 12 |
| 16***78 | Seal-Valve Stem; (Exhaust) | 24 |
234-5985 Cylinder Head Gp
| 09***24 | Ring; (Retaining) | 1 |
| 13***49 | Spacer; (45x53x10-mm Thk) | 2 |
| 13***51 | Seal; (Lip Type) | 1 |
172-6764 Damper & Pulley Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 17***64 | Damper & Pulley Group | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 2 |
200-3313 Drive Gp-Fan
| 0V***23 | Bolt 4.25 In. (10.795 cm) Long | 12 |
| 19***13 | Flywheel As | 1 |
| 20***13 | Drive Group-Fan | 1 |
295-9637 Drive Gp-Fan
| 10***26 | Dowel | 1 |
| 29***37 | Drive Group-Fan | 1 |
| 9X***72 | Bolt-Locking; (3/8-16x0.875-In) | 16 |
4p-6846 Fastener Gp-Front Housing
| 03***85 | Bolt-12 Point Hd-Engine Flywheel To | 6 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
| 10***68 | Bearing-Sleeve | 1 |
109-1657 Fastener Gp-Valve Mechanism
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
194-7097 Flywheel Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 2 |
204-2114 Gear Gp-Camshaft
| 10***14 | Housing As | 1 |
| 16***30 | Bolt; (3/8-16x1.625-In)(Marked Y) | 6 |
| 16***32 | Bolt; (3/8-16x2-In)(3/8-16x2-In) | 6 |
137-5921 Gear Gp-Front
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 3 |
4p-9823 Gear Gp-Rear
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 3 |
7e-8996 Housing Gp-Flywheel
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 4 |
| 10***86 | Eye-Lifting | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 4 |
351-0059 Housing Gp-Flywheel
| 19***98 | Rocker Arm Group | 3 |
| 35***59 | Housing Group-Flywheel | 1 |
| 6I***58 | Bridge-Valve | 12 |
172-4850 Housing Gp-Front
| 17***50 | Housing Group-Front | 1 |
| 27***31 | Rocker Arm Group | 3 |
| 6I***58 | Bridge-Valve | 12 |
111-2088 Lifting Gp-Engine
| 11***88 | Lifting Group-Engine; (Rear) | 1 |
| 13***73 | Support As | 6 |
| 14***82 | Mount-Flexible | 6 |
112-2418 Lifting Gp-Engine
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 18 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
148-7482 Mechanism Gp-Fuel Pump & Valve
| 12***91 | Pulley; (8-Groove)(Alternator) | 1 |
| 13***23 | Pulley As; (Idler) | 2 |
| 14***31 | Support-Alternator | 1 |
6i-1940 Mechanism Gp-Fuel Pump & Valve
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 18 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
151-6660 Mounting Gp-Engine
| 03***13 | Seal-O-Ring | 2 |
| 10***70 | Button | 4 |
| 15***60 | Mounting Group-Engine | 1 |
219-1494 Pan Gp-Oil
| 06***39 | Seal-O-Ring | 2 |
| 10***70 | Button | 4 |
| 16***75 | Rocker Arm As; (Exhaust) | 2 |
172-9944 Pan Gp-Oil
| 03***13 | Seal-O-Ring | 2 |
| 06***39 | Seal-O-Ring | 2 |
| 17***44 | Pan Group-Oil | 1 |
134-3071 Piston & Rod Gp
| 06***39 | Seal-O-Ring | 2 |
| 13***71 | Piston & Rod Group | 1 |
| 19***51 | Button; (24-mm Od) | 2 |
353-9978 Plate As-Front Housing
| 30***22 | Shaft As-Rocker Arm, Exhaust Manifold | 1 |
| 32***96 | Rocker Arm Group; -Intake | 2 |
| 32***38 | Rocker Arm Group; -Exhaust | 2 |
234-5986 Plug Gp-Cylinder Head
| 23***86 | Plug Group-Cylinder Head | 1 |
| 25***21 | Button | 1 |
| 27***91 | Screw-Arm Adjustment; (3/8-24x1.20-In) | 1 |
166-1321 Pulley Gp
| 14***67 | Seal Group-Crankshaft; (Front) | 1 |
| 16***21 | Pulley Group | 1 |
207-5244 Rocker Arm Gp
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 15***80 | Elbow | 1 |
328-4238 Rocker Arm Gp
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
278-1931 Rocker Arm Gp
| 17***63 | Base Group-Oil Filter; -Engine | 1 |
| 1P***67 | Plunger; (Engine Oil Cooler Relief Valve) | 2 |
| 27***31 | Rocker Arm Group | 1 |
198-9898 Rocker Arm Gp
| 19***98 | Rocker Arm Group | 1 |
| 20***44 | Rocker Arm Group | 3 |
| 6I***58 | Bridge-Valve | 12 |
320-2796 Rocker Arm Gp
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 2 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 32***96 | Rocker Arm Group; -Intake | 1 |
328-4237 Rocker Arm Gp
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 16***61 | Cap As-Engine Oil Filler; (Engine Oil) | 1 |
| 17***25 | Tube As | 1 |
328-4239 Rocker Arm Gp
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 6 |
163-7381 Rocker Arm Gp
| 16***81 | Rocker Arm Group | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 8 |
| 6F***82 | Bolt 13.3 cm(5.25 In.) Long-Location "A" | 8 |
319-7401 Seal Gp-Crankshaft
| 18***76 | Hose-Fumes | 1 |
| 31***01 | Seal Group-Crankshaft; -Front | 1 |
| 5P***69 | Clip | 1 |
7e-4876 Support Gp-Engine
| 7E***76 | Support Group-Engine | 1 |
208-2820 Valve Mechanism Gp
| 11***68 | Seal-O-Ring; (15.54mm Id) | 1 |
| 16***70 | Plug | 3 |
| 19***70 | Tube As-Guide | 1 |
Cooling System
151-6652 Fan Gp-Suction
| 10***58 | End-Hose | 1 |
| 14***67 | Clamp; (Hose) | 1 |
| 15***52 | Fan Group-Suction | 1 |
235-6472 Fitting Gp-Radiator Vent
| 09***35 | Clamp | 2 |
| 09***01 | Cap-Radiator | 1 |
| 21***94 | Drain As | 1 |
109-9997 Fitting Gp-Radiator Vent
| 10***97 | Fitting Group-Radiator Vent | 1 |
| 19***80 | Core As | 1 |
| 21***27 | Radiator Group | 1 |
187-6662 Lines Gp-Water
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 18***62 | Lines Group-Water | 1 |
| 5H***04 | Packing,Preformed Elbow Part Of Kit P/N 5r***26 | 2 |
159-3956 Lines Gp-Water
| 10***69 | Filter Element As-Air; (Primary) | 1 |
| 10***73 | Filter Element As-Air; (Secondary) | 1 |
| 11***76 | Cover As | 1 |
135-4925 Pump Gp-Water
| 09***92 | Clamp, Hose | 1 |
| 10***73 | Clip | 1 |
| 13***25 | Pump Group-Water | 1 |
100-9347 Pump Gp-Water
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 4 |
| 10***47 | Pump Group-Water | 1 |
| 10***25 | Gasket; (Air Inlet Manifold)(Intake Manifold Inlet) | 1 |
210-8025 Radiator & Aftercooler Gp
| 10***25 | Gasket; (Air Inlet Manifold)(Intake Manifold Inlet) | 1 |
| 14***42 | U-Bolt | 2 |
| 17***25 | Hose | 1 |
210-8027 Radiator Gp
| 15***58 | Air Cleaner Group | 1 |
| 21***27 | Radiator Group | 1 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 4 |
210-7989 Radiator Gp
| 15***41 | Clip | 2 |
| 17***74 | Pipe As | 1 |
| 21***89 | Radiator Group | 1 |
210-8026 Radiator Gp
| 10***54 | Manifold-Exhaust; (Center) | 1 |
| 10***08 | Manifold-Exhaust; (End)(End) | 2 |
| 10***92 | Stud-Taperlock; (3/8-16x3.93in) | 11 |
196-8182 Radiator Gp
| 13***03 | Support-Exhaust Pipe | 1 |
| 19***82 | Radiator Group | 1 |
| 2N***65 | Bolt-High Temperature; (3/8-16x1.75-In) | 2 |
Electrical And Starting System
170-6979 Alarm Gp-Travel
| 11***55 | Control Group-Engine Electronic; (Engine Electronic) | 1 |
| 14***84 | Plate | 1 |
| 17***79 | Alarm Group-Travel | 1 |
166-1325 Alternator Gp-Charging
| 12***74 | Screw-Pan Head; (8-32x9.52-mm) | 1 |
| 16***25 | Alternator Group-Charging | 1 |
| 21***50 | Control Group-Engine Electronic | 1 |
177-9953 Alternator Gp-Charging
| 16***03 | Electronics Group-Monitor | 1 |
| 16***39 | Electronics Group-Monitor | 1 |
| 17***53 | Alternator Group-Charging; (24-Volt, 80-Ampere) | 1 |
3e-7577 Alternator Gp-Charging
| 14***87 | Spacer; (8.2x12.7x43.6-mm) | 4 |
| 15***99 | Control Group-Unprogrammed | 1 |
| 16***89 | Control Group-Unprgmed Monitor; -Vims | 1 |
204-4154 Battery & Wiring Gp
| 13***79 | Film-Identification; (Electronic Control Module) | 1 |
| 17***10 | Module Group-Message Center | 1 |
| 18***38 | Software Group-Monitor; (Message Center) | 1 |
170-6853 Battery & Wiring Gp
| 17***53 | Battery & Wiring Group | 1 |
| 22***82 | Software Group-Machine | 1 |
| 22***94 | Service Group-Machine | 1 |
183-1038 Battery & Wiring Gp
| 13***79 | Film-Identification; (Electronic Control Module) | 1 |
| 18***38 | Battery & Wiring Group | 1 |
| 21***79 | Software Group-Monitor | 1 |
180-0398 Control & Mtg Gp-Engine Elek
| 18***98 | Control & Mtg Group-Engine Elek | 1 |
| 24***59 | Software Group-Monitor; (Software Only) | 1 |
| 24***60 | Control Group-Electronic; (Includes Software) | 1 |
171-2592 Control & Mtg Gp-Machine
| 17***92 | Control & Mtg Group-Machine | 1 |
| 21***90 | Software Group-Monitor | 1 |
| 21***91 | Service Group-Monitor | 1 |
115-3055 Control Gp-Engine Electronic
| 11***55 | Control Group-Engine Electronic; (Engine Electronic) | 1 |
| 17***93 | Cover | 1 |
| 17***17 | Lens As; (Floodlight) | 1 |
151-2099 Control Gp-Unprogrammed
| 15***99 | Control Group-Unprogrammed | 1 |
| 17***93 | Cover | 1 |
| 17***17 | Lens As; (Floodlight) | 1 |
185-2501 Electrical Ar
| 17***93 | Cover | 1 |
| 17***17 | Lens As; (Floodlight) | 1 |
| 17***18 | Band | 1 |
185-2514 Electronics Gp-Machine
| 09***27 | Lockwasher-Tooth; (0.6mm Thk) | 2 |
| 11***28 | Harness As | 2 |
| 15***21 | Lamp Group-Flood; -Chassis, Boom-Boom, Rear | 2 |
164-8239 Electronics Gp-Monitor
| 09***28 | Screw; (Machine) (M4x0.7x12mm) | 4 |
| 09***35 | Screw; (Machine) (M5x0.8x8mm) | 4 |
| 09***42 | Screw; (Machine) (M6x1.0x16mm) | 8 |
195-8985 Electronics Gp-Monitor
| 09***28 | Screw; (Machine) (M4x0.7x12mm) | 4 |
| 09***35 | Screw; (Machine) (M5x0.8x8mm) | 4 |
| 09***42 | Screw; (Machine) (M6x1.0x16mm) | 7 |
164-8203 Electronics Gp-Monitor
| 15***21 | Lamp Group-Flood; -Chassis, Boom-Boom, Rear | 1 |
| 15***23 | Lamp Group-Flood; -Horizontal Rh | 1 |
| 16***03 | Electronics Group-Monitor | 1 |
221-8711 Electronics Gp-Monitor
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 22***11 | Electronics Group-Monitor | 1 |
211-5593 Electronics Gp-Monitor
| 17***32 | Harness As-Panel | 1 |
| 20***39 | Panel Group-Circuit Breaker | 1 |
| 21***93 | Electronics Group-Monitor | 1 |
211-5594 Electronics Gp-Monitor
| 16***93 | Adapter | 1 |
| 19***22 | Sensor Group-Pressure; -Atmospheric Air | 1 |
| 1T***20 | Bolt-12 Point Head; (3/8-16x1.25-In) | 2 |
335-2081 Harness As-Wiring -Power Converter
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
| 33***81 | Harness As-Wiring; -Power Converter | 1 |
153-2523 Lamp Gp-Flood
| 15***23 | Lamp Group-Flood; -Horizontal Rh | 1 |
153-2521 Lamp Gp-Flood
| 15***21 | Lamp Group-Flood; -Chassis, Boom-Boom, Rear | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 3 |
153-2524 Lamp Gp-Flood -Boom, Stick
| 15***24 | Lamp Group-Flood; -Boom, Stick | 1 |
6c-8619 Lighting Gp-Cab
| 18***46 | Sensor Group-Speed; -Low Output-Engine Timing-Transmission | 1 |
| 1V***41 | Seal | 1 |
| 5P***47 | Washer (Bracket To Valve Support) | 1 |
150-7033 Lighting Gp-Chassis -Front
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 2 |
| 15***33 | Lighting Group-Chassis; -Front | 1 |
204-1939 Panel Gp-Circuit Breaker
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 13***61 | Bracket | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
217-2970 Panel Gp-Circuit Breaker
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 21***70 | Panel Group-Circuit Breaker | 1 |
102-7664 Sensor & Mtg Gp-Pressure
| 10***64 | Sensor & Mtg Group-Pressure; -Atmospheric Air | 1 |
| 14***28 | Washer-Spring | 1 |
| 14***50 | Coil As | 1 |
194-6724 Sensor Gp-Pressure
| 17***53 | Battery & Wiring Group | 1 |
| 17***33 | Box & Mounting Group | 1 |
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
194-6722 Sensor Gp-Pressure
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***84 | Switch As-Rocker; (Starting Aid Ether) | 1 |
| 11***73 | Connector; (Receptacle) | 1 |
194-6725 Sensor Gp-Pressure
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
201-6615 Sensor Gp-Speed
| 20***15 | Sensor Group-Speed; -Low Output | 1 |
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
189-5746 Sensor Gp-Speed
| 18***46 | Sensor Group-Speed; -Low Output-Engine Timing-Transmission | 1 |
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
142-8394 Sensor Gp-Speed
| 10***28 | Wire As | 1 |
| 14***94 | Sensor Group-Speed; -Secondary, Timing | 1 |
| 23***62 | Starting Motor Group-Electric | 1 |
201-6617 Sensor Gp-Speed
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
142-8393 Sensor Gp-Speed
| 10***28 | Wire As | 1 |
| 14***93 | Sensor Group-Speed; -Primary, Timing | 1 |
| 4N***59 | Gasket; (Starting Motor) | 1 |
171-8963 Sensor Gp-Speed
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
102-2240 Sensor Gp-Temperature
| 10***40 | Sensor Group-Temperature; -Output Transfer Gear Oil | 1 |
| 2S***78 | Seal-O-Ring (Id=37.47mm) | 1 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
156-2829 Solenoid Gp
| 15***29 | Solenoid Group | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 1 |
| 6V***62 | Screw-Machine; (8-32x0.31-In) | 4 |
151-6665 Starting Aid Gp-Ether
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
180-6783 Starting Ar-Cold Weather
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 10 |
| 15***65 | Kit-Connecting Plug; (8-Pin)(Electronic Control Channel) | 1 |
237-1962 Starting Motor Gp-Electric
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 5 |
| 0T***02 | Bolt; (3/8-16x0.625-In)(Shield To Head) | 1 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 2 |
6v-0890 Starting Motor Gp-Electric
| 20***57 | Wiring Group-Console; -Lh | 1 |
| 20***60 | Wiring Group-Console; -Rh | 1 |
| 6V***90 | Starting Motor Group-Electric; (Delco Remy) | 1 |
105-4729 Starting Motor Gp-Electric
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 3 |
338-3454 Starting Motor Gp-Electric
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
5c-6108 Switch Gp-Refueling -Fuel Tank Shutoff
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***36 | Clip | 3 |
| 11***95 | Switch As | 1 |
7n-0718 Switch Gp-Disconnect -Battery
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 6 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 2 |
7n-0719 Switch Gp-Disconnect -Battery
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 6 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 2 |
125-1302 Switch Gp-Magnetic
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 6 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 2 |
9g-7641 Switch Gp-Start -Engine, Key
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 11***36 | Clip | 3 |
| 11***95 | Switch As | 1 |
153-2914 Wiring Gp-Cab
| 09***28 | Washer; (53x84x1-mm Thk) | 6 |
| 09***91 | Pin - Spring | 3 |
| 09***16 | Setscrew-Socket; (M12x1.75x12-mm) | 2 |
237-2191 Wiring Gp-Cab
| 15***98 | Motor & Mtg Group-Travel | 1 |
| 19***51 | Drive Group-Final | 1 |
| 23***91 | Wiring Group-Cab | 1 |
207-6755 Wiring Gp-Console
| 09***91 | Pin - Spring | 3 |
| 09***16 | Setscrew-Socket; (M12x1.75x12-mm) | 2 |
| 09***94 | Pin-Spring | 7 |
207-6760 Wiring Gp-Console -Rh
| 14***14 | Sprocket Group | 2 |
| 14***97 | Drive Group-Swing | 1 |
| 14***25 | Drive Group-Swing, Piston | 1 |
207-6757 Wiring Gp-Console -Lh
| 15***98 | Motor & Mtg Group-Travel | 1 |
| 19***61 | Drive Group-Final; (Without Motor) | 1 |
| 20***57 | Wiring Group-Console; -Lh | 1 |
172-4294 Wiring Gp-Engine
| 14***70 | Bolt | 28 |
| 17***94 | Wiring Group-Engine | 1 |
| 19***01 | Spacer; (31.5x56x5-mm Thk) | 28 |
186-4619 Wiring Gp-Lubrication
| 13***73 | Bolt As; (M12x1.75x25-mm) | 4 |
| 17***15 | Sheet As-Sound Suppression | 1 |
| 17***16 | Insulation | 1 |
207-6753 Wiring Gp-Platform
| 09***64 | Grommet | 1 |
| 09***43 | Pin-Cotter | 1 |
| 09***80 | Pin; (Clevis) | 1 |
170-6980 Wiring Gp-Refueling Pump
| 13***55 | Bolt; (M8x1.25x8-mm) | 8 |
| 17***80 | Wiring Group-Refueling Pump | 1 |
| 17***33 | Cover As | 1 |
Engine Arrangement
205-5858 Engine Ar-Complete
| 10***65 | Pump Group-Fuel Transfer | 1 |
| 10***47 | Pump Group-Water | 1 |
| 10***64 | Sensor & Mtg Group-Pressure; -Atmospheric Air | 1 |
235-4685 Engine Ar-Complete
| 10***65 | Pump Group-Fuel Transfer | 1 |
| 10***47 | Pump Group-Water | 1 |
| 10***64 | Sensor & Mtg Group-Pressure; -Atmospheric Air | 1 |
235-3469 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 13***71 | Piston & Rod Group | 6 |
159-5810 Engine Ar-Core
| 12***48 | Base Group-Valve Cover & Inj Harn | 1 |
| 12***10 | Injector Group-Fuel | 6 |
| 13***71 | Piston & Rod Group | 6 |
205-6911 Installation Ar-Engine
| 20***58 | Engine Ar-Complete | 1 |
| 20***11 | Installation Ar-Engine | 1 |
| 20***12 | Muffler Group | 1 |
202-4806 Installation Ar-Engine
| 15***52 | Fan Group-Suction | 1 |
| 15***54 | Cooler & Mtg Group-Hydraulic Oil | 1 |
| 15***55 | Extension Group-Exhaust | 1 |
Frame And Body
177-5633 Box & Mounting Gp
| 17***33 | Box & Mounting Group | 1 |
| 19***01 | Spacer; (31.5x56x5-mm Thk) | 122 |
| 19***02 | Bolt; (M30x3.5x235-mm) | 74 |
170-2807 Box & Mtg Gp-Storage
| 14***85 | Seal (1100 cm) (Order By The Centimeter) | 0 |
| 17***07 | Box & Mtg Group-Storage | 1 |
| 19***92 | Gear & Bearing Group-Swing | 1 |
214-8033 Box Gp-Battery
| 11***83 | Seal (1100 cm) (Order By The Centimeter) | 0 |
| 21***33 | Box Group-Battery | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
184-9124 Counterweight Gp
| 14***85 | Seal (1100 cm) (Order By The Centimeter) | 0 |
| 18***24 | Counterweight Group | 1 |
| 22***77 | Seal-Dust | 1 |
199-0072 Cover Gp-Control Valve
| 13***75 | Bolt As-Locking; (M12x1.75x30-mm)(M12x1.75x30-mm)) | 56 |
| 13***77 | Bolt As; (M12x1.75x35-mm) | 25 |
| 13***90 | Cover As | 1 |
184-9091 Cover Gp-Hood
| 13***75 | Bolt As-Locking; (M12x1.75x30-mm)(M12x1.75x30-mm)) | 56 |
| 13***77 | Bolt As; (M12x1.75x35-mm) | 25 |
| 13***90 | Cover As | 1 |
203-5096 Door As-Access -Engine Compartment
| 12***84 | Guard As | 1 |
| 14***18 | Nut; (M6x1-Thd) | 8 |
| 20***96 | Door As-Access; -Engine Compartment | 1 |
203-5101 Door As-Access
| 13***57 | Bracket As | 4 |
| 20***01 | Door As-Access | 1 |
| 21***57 | Guard | 1 |
177-5580 Door Gp-Access
| 10***66 | Bolt; (Self Locking) (M16x2x40mm) | 2 |
| 10***40 | Cover As | 1 |
| 10***41 | Spacer (17mm Id) | 10 |
184-5674 Frame Gp-Upper
| 13***73 | Bolt As; (M12x1.75x25-mm) | 10 |
| 13***75 | Bolt As-Locking; (M12x1.75x30-mm)(M12x1.75x30-mm)) | 84 |
| 13***77 | Bolt As; (M12x1.75x35-mm) | 27 |
227-6098 Gear & Bearing Gp-Swing
| 09***19 | Pin, Clevis; (Clevis) | 2 |
| 09***20 | Pin-Clevis | 2 |
| 13***73 | Bolt As; (M12x1.75x25-mm) | 22 |
199-4491 Gear & Bearing Gp-Swing
| 09***43 | Pin-Cotter | 1 |
| 09***20 | Knob | 1 |
| 09***72 | Grommet | 1 |
227-6099 Gear & Bearing Gp-Swing
| 13***00 | Liner | 1 |
| 17***35 | Liner | 1 |
| 17***36 | Liner | 1 |
148-4650 Gear & Bearing Gp-Swing
| 09***43 | Pin-Cotter | 1 |
| 09***20 | Knob | 1 |
| 09***72 | Grommet | 1 |
199-4492 Gear & Bearing Gp-Swing
| 09***43 | Pin-Cotter | 1 |
| 09***20 | Knob | 1 |
| 09***72 | Grommet | 1 |
204-0045 Guard Ar
| 09***92 | Locknut; (M6x1-Thd) | 8 |
| 12***60 | Lever As | 1 |
| 13***88 | Shim (1.6mm Thick) | 1 |
237-8773 Guard Gp-Bottom
| 18***11 | Pump Group-Lubrication | 1 |
| 18***62 | Lines Group-Grease | 1 |
| 18***19 | Wiring Group-Lubrication | 1 |
168-1716 Guard Gp-Bottom
| 10***02 | Clip; (Ladder) | 2 |
| 16***16 | Guard Group-Bottom | 1 |
| 17***90 | Panel As-Sound Suppression | 1 |
205-0480 Guard Gp-Lighting
| 10***09 | Connector As | 12 |
| 10***10 | Connector As | 5 |
| 10***11 | Sleeve; (6.5mm Id) | 2 |
139-0454 Guard Gp-Swing Motor
| 10***09 | Connector As | 12 |
| 10***10 | Connector As | 5 |
| 10***11 | Sleeve; (6.5mm Id) | 2 |
172-2954 Guard Gp-Swivel
| 17***54 | Guard Group-Swivel | 1 |
| 17***88 | Liner | 1 |
| 17***89 | Liner | 1 |
168-1718 Handrail Gp
| 13***06 | Liner | 1 |
| 16***18 | Handrail Group | 1 |
| 17***74 | Liner | 1 |
184-9121 Hood & Guard Gp
| 17***16 | Insulation | 1 |
| 17***17 | Insulation | 1 |
| 18***21 | Hood & Guard Group | 1 |
168-1717 Hood & Guard Gp
| 16***27 | Liner | 2 |
| 16***17 | Hood & Guard Group | 1 |
| 17***32 | Liner | 2 |
184-9122 Hood & Guard Gp
| 17***07 | Insulation | 1 |
| 17***32 | Liner | 1 |
| 18***22 | Hood & Guard Group | 1 |
177-5634 Hood Gp-Engine
| 17***11 | Insulation | 1 |
| 17***12 | Insulation | 1 |
| 17***34 | Hood Group-Engine | 1 |
177-5663 Hood Gp-Engine
| 17***08 | Liner | 1 |
| 17***43 | Liner | 1 |
| 17***61 | Liner | 1 |
172-6091 Panel Gp-Sound Suppression
| 10***48 | Seal; (0.5-M Each) | 0 |
| 17***91 | Panel Group-Sound Suppression | 1 |
| 4I***24 | Washer; (4.5x40x1.2-mm Thk) | 4 |
180-6810 Pump & Lines Gp-Automatic Lube
| 18***10 | Pump & Lines Group-Automatic Lube | 1 |
| 19***75 | Sheet-Rubber | 1 |
| 21***82 | Sheet-Rubber | 1 |
180-6811 Pump Gp-Lubrication
| 17***89 | Liner | 1 |
| 18***11 | Pump Group-Lubrication | 1 |
| 21***86 | Sheet-Rubber | 1 |
214-8378 Sheet As-Sound Suppression
| 10***60 | Support As; (60mm) | 16 |
| 14***11 | Spacer; (30.5x55.X24mm Thk) | 32 |
| 17***00 | Guard As-Track Guide | 4 |
175-0830 Sheet As-Sound Suppression
| 17***08 | Liner | 1 |
| 17***30 | Sheet As-Sound Suppression | 1 |
| 17***43 | Liner | 1 |
175-0913 Sheet As-Sound Suppression
| 13***72 | Bolt As; (M12x1.75x20-mm) | 8 |
| 13***18 | Walkway As | 1 |
| 17***13 | Sheet As-Sound Suppression | 1 |
214-8011 Sheet As-Sound Suppression
| 10***47 | Plug | 24 |
| 10***11 | Spacer; (37x70x65-mm Thk) | 36 |
| 14***00 | Step | 4 |
214-8381 Sheet As-Sound Suppression
| 14***11 | Spacer; (30.5x55.X24mm Thk) | 24 |
| 17***08 | Guard As-Track Guide | 2 |
| 18***87 | Guard As-Track Guide | 4 |
214-8389 Sheet As-Sound Suppression
| 14***09 | Idler Group-Front | 2 |
| 16***43 | Adjustment Group-Hydraulic Track | 2 |
| 21***89 | Sheet As-Sound Suppression | 1 |
214-8016 Sheet As-Sound Suppression
| 14***11 | Spacer; (30.5x55.X24mm Thk) | 8 |
| 17***08 | Guard As-Track Guide | 2 |
| 21***16 | Sheet As-Sound Suppression | 1 |
214-8387 Sheet As-Sound Suppression
| 10***66 | Bolt; (Self Locking) (M16x2x40mm) | 48 |
| 17***63 | Cover As; (Rh) | 1 |
| 17***64 | Cover As; (Lh) | 1 |
175-0797 Sheet As-Sound Suppression
| 13***06 | Liner | 1 |
| 17***97 | Sheet As-Sound Suppression | 1 |
| 17***74 | Liner | 1 |
214-8383 Sheet As-Sound Suppression
| 10***60 | Support As; (60mm) | 16 |
| 14***11 | Spacer; (30.5x55.X24mm Thk) | 32 |
| 17***00 | Guard As-Track Guide | 4 |
218-7758 Sheet As-Sound Suppression -Radiator
| 14***11 | Spring Group-Recoil | 1 |
| 19***57 | Motor Housing; Assembly, Drive, Motor Housing; Assembly, Drive, Idler Group-Front | 1 |
| 21***58 | Sheet As-Sound Suppression; -Radiator | 1 |
175-0976 Sheet As-Sound Suppression
| 09***27 | Valve-Fill; (Track Tension Cylinder) | 1 |
| 13***42 | Piston | 1 |
| 13***43 | Seal-Lip Type | 1 |
175-0876 Sheet As-Sound Suppression
| 13***72 | Bolt As; (M12x1.75x20-mm) | 8 |
| 17***92 | Walkway As | 1 |
| 17***76 | Sheet As-Sound Suppression | 1 |
175-0786 Sheet As-Sound Suppression
| 17***86 | Sheet As-Sound Suppression | 1 |
| 17***34 | Insulation | 1 |
| 21***92 | Sheet-Rubber | 1 |
184-8884 Sheet As-Sound Suppression
| 09***27 | Valve-Fill; (Track Tension Cylinder) | 1 |
| 13***43 | Seal-Lip Type | 1 |
| 13***44 | Ring | 1 |
203-4880 Sheet As-Sound Suppression
| 14***08 | Idler Group-Front | 1 |
| 14***12 | Roller Ar-Track & Carrier | 1 |
| 14***50 | Gear & Bearing Group-Swing | 1 |
218-7761 Sheet As-Sound Suppression
| 19***57 | Motor Housing; Assembly, Drive, Motor Housing; Assembly, Drive, Idler Group-Front | 1 |
| 21***61 | Sheet As-Sound Suppression | 1 |
| 23***79 | Spring Group-Recoil | 1 |
184-8531 Walkway Gp
| 10***83 | Plug; (Hex Socket) (1/4 Npt) (Early) (Current Brake Housing May Be Visually Distinguished From The Early Design By Locating The -6 Orb Plug At The "B" Brake Pressure Port) (The Early Design Used A Socket Head, 1/4 Npt Plug) | 2 |
| 17***25 | Seal Group-Duo-Cone | 2 |
| 18***31 | Walkway Group | 1 |
Fuel System
220-2422 Adapter Gp-Fast Fill Fuel
| 09***61 | Strap; (Cable) | 6 |
| 17***75 | Support As | 1 |
| 17***79 | Support As | 2 |
205-6829 Cooler Gp-Fuel
| 11***28 | Seal | 1 |
| 12***38 | Housing; (Receptacle) | 1 |
| 12***39 | Terminal; (Male) | 2 |
128-1471 Filter Gp-Fuel
| 12***71 | Filter Group-Fuel | 1 |
| 17***80 | Wiring Group-Refueling Pump | 1 |
| 18***54 | Pump Group-Refueling | 1 |
133-5671 Filter Gp-Water Sep & Fuel
| 13***71 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 18***23 | Pump As-Fuel Priming | 1 |
| 8T***05 | Washer, Flat-Thin(1/4); W/O Freespool Qty Is 12 | 1 |
223-3095 Gauge Gp-Sight -Fuel Level
| 10***72 | Cover; (Hydraulic Pump Drive) | 1 |
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 2 |
| 1T***65 | Bolt 2.54 cm (1" Long) | 2 |
128-8510 Injector Gp-Fuel
| 00***07 | Elbow; (90 Degree) | 2 |
| 10***56 | Hose (400cm); (400-cm) | 0 |
| 10***01 | Connector-Hose | 3 |
208-4100 Lines Gp-Fuel
| 09***07 | Shim (0.4mm Thick) | 6 |
| 09***08 | Shim (1.0mm Thick) | 6 |
| 13***72 | Bolt As; (M12x1.75x20-mm) | 2 |
173-0004 Lines Gp-Fuel -Rear
| 09***07 | Shim (0.4mm Thick) | 6 |
| 09***08 | Shim (1.0mm Thick) | 6 |
| 13***72 | Bolt As; (M12x1.75x20-mm) | 2 |
237-8812 Lines Gp-Fuel
| 06***13 | Connector-Flared | 1 |
| 09***47 | Bolt; (M10x1.5x36-mm) | 2 |
| 09***36 | Screw; (Machine) (M5x0.8x10mm) | 5 |
171-9078 Mounting Gp-Fuel Filter
| 06***13 | Connector-Flared | 1 |
| 09***36 | Screw; (Machine) (M5x0.8x10mm) | 5 |
| 09***86 | Clamp; (Hose) | 1 |
165-4962 Pump & Motor Gp-Refueling
| 06***13 | Connector-Flared | 1 |
| 09***36 | Screw; (Machine) (M5x0.8x10mm) | 5 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
180-6894 Pump Ar-Refueling
| 18***94 | Pump Ar-Refueling | 1 |
| 28***25 | Valve Group-Check; -Fuel | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 1 |
183-2824 Pump Gp-Fuel Priming -Manual
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 18***24 | Pump Group-Fuel Priming; -Manual | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
100-4265 Pump Gp-Fuel Transfer
| 10***65 | Pump Group-Fuel Transfer | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 21***00 | Back-Up Alarm Assem. | 1 |
180-6854 Pump Gp-Refueling
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
| 10***56 | Diode As; (Alternator) | 1 |
184-8528 Tank & Mtg Gp-Fuel
| 18***28 | Tank & Mtg Group-Fuel | 1 |
| 18***38 | Collar | 2 |
| 18***39 | Fan As; (Alternator) | 1 |
237-8771 Tank Gp-Fuel
| 09***63 | Grommet | 1 |
| 09***62 | Washer; (Hard) (3.4x7x0.8mm Thk) | 4 |
| 0S***95 | Bolt 1.25 In. (31.75 mm) Long Guard Assemblies To Radiator Guard | 1 |
218-7945 Tank Gp-Fuel
| 20***54 | Battery & Wiring Group | 1 |
| 20***53 | Wiring Group-Platform | 1 |
| 21***45 | Tank Group-Fuel | 1 |
184-8529 Tank Gp-Fuel
| 11***37 | Clip | 15 |
| 15***22 | Bolt; (M10x1.5x250-mm) | 4 |
| 17***65 | Cable As | 1 |
233-6742 Valve Gp-Check -Fuel
| 09***63 | Grommet | 1 |
| 09***62 | Washer; (Hard) (3.4x7x0.8mm Thk) | 4 |
| 10***00 | Battery | 1 |
281-2725 Valve Gp-Check -Fuel
| 09***63 | Grommet | 1 |
| 09***62 | Washer; (Hard) (3.4x7x0.8mm Thk) | 4 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 4 |
Hydraulic System
160-4138 Accumulator & Mtg Gp-Hydraulic
| 16***38 | Accumulator & Mtg Group-Hydraulic | 1 |
| 21***25 | Hub | 1 |
| 21***26 | Cage-Spring | 4 |
215-4907 Accumulator Gp-Hydraulic -Uncharged
| 13***73 | Bolt As; (M12x1.75x25-mm) | 11 |
| 21***07 | Accumulator Group-Hydraulic; -Uncharged | 1 |
| 25***33 | Cover As | 1 |
215-4906 Accumulator Gp-Hydraulic -Uncharged
| 13***73 | Bolt As; (M12x1.75x25-mm) | 11 |
| 19***42 | Cover As | 1 |
| 19***46 | Sheet As | 1 |
215-4905 Accumulator Gp-Hydraulic -Uncharged
| 19***33 | Coupling Group-Flexible | 1 |
| 21***05 | Accumulator Group-Hydraulic; -Uncharged | 1 |
| 8T***35 | Capscrew, Hexhead; (1/2-13 X 2 Pltd.) | 8 |
209-5982 Actuator Gp
| 11***50 | Seal - Lip Type | 2 |
| 18***65 | Cylinder Group-Boom | 1 |
| 20***82 | Actuator Group; -Hydraulic Fan Pump | 1 |
158-9103 Actuator Gp-Pump
| 10***85 | Cylinder Group-Bucket | 1 |
| 15***03 | Actuator Group-Pump; -Maximum Angle | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
158-9104 Actuator Gp-Pump
| 12***18 | Cylinder Group-Bucket | 1 |
| 15***04 | Actuator Group-Pump; -Minimum Angle | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 2 |
173-3503 Base Gp-Oil Filter -Hydraulic
| 17***03 | Base Group-Oil Filter; -Hydraulic | 1 |
| 6E***72 | Cylinder Group-Stick | 1 |
| 9X***00 | Seal; (Id=129.85mm) | 4 |
129-8053 Base Gp-Oil Filter -Hydraulic
| 12***53 | Base Group-Oil Filter; -Hydraulic | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
| 4I***93 | Cylinder Group-Master | 1 |
151-6654 Cooler & Mtg Gp-Hydraulic Oil
| 10***86 | Cylinder As | 1 |
| 10***90 | Rod As | 1 |
| 12***00 | Head | 1 |
210-8157 Cooler Gp-Hydraulic Oil
| 09***74 | Setscrew-Socket; (M6x1x16-mm) | 1 |
| 09***33 | Seal-O-Ring; (Id=209.30mm) | 1 |
| 10***61 | Head | 1 |
210-8103 Cooler Gp-Hydraulic Oil
| 12***92 | Head | 1 |
| 12***93 | Seal-Buffer | 1 |
| 12***94 | Seal-U-Cup | 1 |
210-8002 Cooler Gp-Hydraulic Oil
| 08***50 | Ring; (Back Up) | 1 |
| 09***71 | Ring; (Retaining) | 1 |
| 09***35 | Seal-O-Ring (Id=149.60mm) | 1 |
196-8133 Coupling Gp-Flexible
| 09***74 | Setscrew-Socket; (M6x1x16-mm) | 1 |
| 09***33 | Seal-O-Ring; (Id=209.30mm) | 1 |
| 10***64 | Ring; (Retaining) | 1 |
151-6646 Coupling Gp-Pump
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 3 |
| 13***07 | Adapter Group-Pump Drive; -Remote | 1 |
| 15***46 | Coupling Group-Pump | 1 |
191-5596 Cover Gp-Pump
| 14***98 | Drive Group-Swing; -Without Motor, Front | 1 |
| 15***01 | Motor & Mtg Group-Swing | 1 |
| 19***96 | Cover Group-Pump | 1 |
185-0164 Cylinder & Seal Gp-Boom
| 09***30 | Ring; (Retaining) | 1 |
| 09***50 | Coupling-Pipe | 1 |
| 09***28 | Washer; (53x84x1-mm Thk) | 8 |
121-1512 Cylinder & Seal Gp-Bucket
| 12***12 | Cylinder & Seal Group-Bucket | 1 |
| 14***26 | Drive Group-Swing; -Without Motor, Rear | 1 |
| 15***03 | Motor & Mtg Group-Swing | 1 |
105-7484 Cylinder & Seal Gp-Bucket
| 09***30 | Ring; (Retaining) | 1 |
| 09***28 | Washer; (53x84x1-mm Thk) | 8 |
| 09***41 | Ring - Retaining | 1 |
4i-5692 Cylinder & Seal Gp-Master
| 09***30 | Ring; (Retaining) | 1 |
| 09***50 | Coupling-Pipe | 1 |
| 09***28 | Washer; (53x84x1-mm Thk) | 8 |
4i-7735 Cylinder & Seal Gp-Stick
| 14***65 | Elbow | 3 |
| 14***90 | Elbow Group | 1 |
| 14***49 | Tee Group; (Swivel) | 1 |
185-0165 Cylinder Gp-Boom
| 14***65 | Elbow | 3 |
| 14***90 | Elbow Group | 1 |
| 14***49 | Tee Group; (Swivel) | 1 |
105-7485 Cylinder Gp-Bucket
| 10***85 | Cylinder Group-Bucket | 1 |
| 4T***88 | Filter-Oil; (Advanced Efficiency)(Hydraulic) | 1 |
121-1518 Cylinder Gp-Bucket
| 09***10 | Seal-O-Ring; (Id=4.80mm) | 6 |
| 09***81 | Seal-O-Ring | 1 |
| 12***18 | Cylinder Group-Bucket | 1 |
4i-5693 Cylinder Gp-Master
| 09***59 | Screw-Machine; (M6x1x3.4-mm) | 2 |
| 11***54 | Cover | 2 |
| 11***82 | Seal-O-Ring (Id=74.5mm) | 2 |
6e-4272 Cylinder Gp-Stick
| 09***59 | Screw-Machine; (M6x1x3.4-mm) | 2 |
| 11***54 | Cover | 2 |
| 11***82 | Seal-O-Ring (Id=74.5mm) | 2 |
209-2917 Cylinder Gp-Stick
| 10***78 | Bolt; (Socket Head) (M10x1.5x35mm) | 4 |
| 14***91 | Indicator-Restriction | 1 |
| 14***90 | Filter Element-Oil; (Ultra High Efficiency)(Hydraulic) | 1 |
6i-3638 Drive Gp-Pump
| 09***81 | Seal-O-Ring | 1 |
| 12***81 | Filter Element As-Oil; (Standard Efficiency)(Hydraulic, Return) | 1 |
| 13***23 | Seal-O-Ring | 4 |
148-4598 Drive Gp-Swing -Without Motor, Front
| 09***81 | Seal-O-Ring | 1 |
| 13***23 | Seal-O-Ring | 4 |
| 13***24 | Screw; (M3x0.5x5-mm) | 8 |
148-4625 Drive Gp-Swing
| 09***59 | Screw-Machine; (M6x1x3.4-mm) | 2 |
| 11***54 | Cover | 2 |
| 11***82 | Seal-O-Ring (Id=74.5mm) | 2 |
148-4626 Drive Gp-Swing -Without Motor, Rear
| 10***84 | Bolt-Socket Head; (M10x1.5x25-mm) | 4 |
| 14***90 | Filter Element-Oil; (Ultra High Efficiency)(Hydraulic) | 1 |
| 14***26 | Drive Group-Swing; -Without Motor, Rear | 1 |
148-4597 Drive Gp-Swing
| 10***36 | Seal-O-Ring; (49.28mm Id) | 1 |
| 14***97 | Drive Group-Swing | 1 |
| 18***37 | Filter-Oil; (Advanced Efficiency)(Hydraulic) | 1 |
191-2573 Fastener Gp-Swing & Final Dr
| 09***19 | Seal-O-Ring (Id=15.80mm) | 4 |
| 19***73 | Fastener Group-Swing & Final Dr | 1 |
| 23***57 | Pipe | 1 |
201-0496 Filter & Lines Gp-Hydraulic -Hydraulic Return
| 11***61 | Plate As | 1 |
| 11***65 | Plate As | 1 |
| 11***69 | Channel As | 1 |
126-2080 Filter Gp-Oil
| 11***77 | Shaft | 4 |
| 11***79 | Spacer; (17.5x24x5-mm Thk) | 4 |
| 11***86 | Channel As | 1 |
165-3888 Filter Gp-Oil
| 14***68 | Film-Identification; (Biodegradable Hydraulic Oil) | 1 |
| 16***88 | Filter Group-Oil | 1 |
| 20***96 | Filter & Lines Group-Hydraulic; -Hydraulic Return | 1 |
188-4142 Filter Gp-Oil -Hydraulic Return
| 09***30 | Screw-Machine; (M4x0.07x6-mm) | 2 |
| 11***69 | Lever | 1 |
| 11***70 | Support Assem. | 1 |
6e-5534 Filter Gp-Oil -Hydraulic
| 11***77 | Shaft | 4 |
| 11***79 | Spacer; (17.5x24x5-mm Thk) | 4 |
| 11***98 | Plate As; (Lh) | 1 |
173-3511 Filter Gp-Oil
| 17***11 | Filter Group-Oil; -Hydraulic Return | 1 |
| 20***96 | Filter & Lines Group-Hydraulic; -Hydraulic Return | 1 |
188-4147 Filter Gp-Oil
| 11***67 | Tube As | 2 |
| 12***40 | Elbow | 2 |
| 13***53 | Flange-Special | 4 |
188-4150 Filter Gp-Oil
| 11***67 | Tube As | 2 |
| 12***40 | Elbow | 2 |
| 13***53 | Flange-Special | 4 |
250-0729 Filter Gp-Oil -Hydraulic
| 11***67 | Tube As | 2 |
| 12***40 | Elbow | 2 |
| 13***53 | Flange-Special | 4 |
126-2112 Filter Gp-Oil
| 12***12 | Filter Group-Oil; -Hydraulic Return | 1 |
| 15***45 | Pump & Mtg Group-Main Hydraulic | 1 |
| 15***47 | Pump & Mtg Group-Hydraulic | 1 |
185-0336 Filter Gp-Oil -Hydraulic
| 18***36 | Filter Group-Oil; -Hydraulic | 1 |
| 24***82 | Cover | 2 |
| 24***83 | Gasket | 2 |
227-0620 Gauge Gp-Sight -Hydraulic Oil Level
| 11***67 | Tube As | 2 |
| 12***40 | Elbow | 2 |
| 13***53 | Flange-Special | 4 |
204-0046 Guard Ar-Cylinder
| 10***03 | Bolt-Socket Head; (M16x2x35-mm) | 4 |
| 12***09 | Clip | 4 |
| 12***14 | Clip | 14 |
117-8060 Guard Gp-Cylinder -Master
| 10***03 | Clamp; (Half) | 4 |
| 10***11 | Support As | 2 |
| 10***62 | Support As | 1 |
117-8097 Guard Gp-Cylinder -Stick
| 08***91 | Spacer; (15.5x30x12-mm Thk) | 1 |
| 10***96 | Bolt-Socket Head; (M10x1.5x50-mm) | 12 |
| 10***57 | Hose As (Nom 15, L=1250mm) | 1 |
204-0047 Guard Gp-Cylinder -Boom
| 08***56 | 90 Degrees Elbow | 1 |
| 08***31 | Hose As (Nom 06, L=600mm) | 1 |
| 08***32 | Hose As (Nom 06, L=900mm) | 1 |
191-5593 Head Gp-Pump
| 08***56 | 90 Degrees Elbow | 1 |
| 08***31 | Hose As (Nom 06, L=600mm) | 1 |
| 08***32 | Hose As (Nom 06, L=900mm) | 1 |
201-5340 Hydraulic Ar
| 09***85 | Locknut; (M16x2-Thd) | 2 |
| 09***69 | Bolt | 4 |
| 11***18 | Hose As | 1 |
190-7718 Hydraulic Ar
| 08***56 | 90 Degrees Elbow | 1 |
| 08***31 | Hose As (Nom 06, L=600mm) | 1 |
| 08***32 | Hose As (Nom 06, L=900mm) | 1 |
201-4923 Hydraulic Ar
| 08***56 | 90 Degrees Elbow | 1 |
| 08***31 | Hose As (Nom 06, L=600mm) | 1 |
| 08***32 | Hose As (Nom 06, L=900mm) | 1 |
274-2484 Kit-Indicator -Hydraulic Oil Filter
| 14***11 | Plug Group | 1 |
| 15***71 | Valve Group-Shutoff; -Hydraulic Pump, Tank | 1 |
| 20***82 | Pipe As | 1 |
159-7744 Lever Gp-Control
| 08***29 | Block | 1 |
| 10***98 | Name-Plate (Type Of Machine:Ex1100), Bolt-Socket Head; (M10x1.5x40-mm) | 4 |
| 10***02 | Bolt-Socket Head; (M12x1.75x30-mm) | 12 |
184-9173 Lines Gp-Bucket -Bottom Dump
| 10***15 | Elbow Group | 1 |
| 11***20 | Valve Group-Swing Cushion; -Anti-Reaction, Fine Swing | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 3 |
235-4908 Lines Gp-Bucket -Bottom Dump
| 11***21 | Bolt-Socket Head; (M16x2.0x55mm) | 12 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 2 |
| 14***39 | Connector As. | 1 |
184-9167 Lines Gp-Front
| 07***41 | Seal; (30.3mm Od) | 3 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***74 | Solenoid As-Proportional; (Pilot Control Actuator) | 3 |
184-9171 Lines Gp-Front Shovel
| 03***05 | Seal-O-Ring | 3 |
| 11***85 | Retainer | 3 |
| 11***86 | Spring | 3 |
168-9368 Lines Gp-Motor
| 09***87 | Seal-O-Ring | 1 |
| 15***02 | Motor Group-Swing | 1 |
| 16***68 | Lines Group-Motor | 1 |
207-9585 Lines Gp-Pilot
| 09***73 | Bolt; (Socket Head) (M12x1.75x60mm) | 4 |
| 10***62 | Dowel | 2 |
| 12***85 | Seal-O-Ring | 1 |
168-9376 Lines Gp-Pump
| 09***90 | Bolt-Socket Head; (M14x2x60-mm) | 4 |
| 10***62 | Dowel | 2 |
| 16***19 | Seal-Shaft | 1 |
168-9381 Lines Gp-Pump -Shutoff Valve
| 09***73 | Seal-O-Ring (Id=5.80mm) | 2 |
| 13***16 | Valve Group | 1 |
| 16***81 | Lines Group-Pump; -Shutoff Valve | 1 |
168-9375 Lines Gp-Return & Filter
| 09***74 | Seal-O-Ring (Id=6.8mm); (Id=6.80mm) | 2 |
| 13***13 | Valve Group-Solenoid | 1 |
| 16***75 | Lines Group-Return & Filter | 1 |
168-9373 Lines Gp-Swing Motor
| 09***30 | Ring-Retaining; (External) | 1 |
| 09***65 | Plug, Tapered | 2 |
| 09***78 | Seal-O-Ring (Id=9.80mm) | 2 |
187-7090 Lines Gp-Travel Motor
| 09***48 | Nipple, Grease | 2 |
| 11***44 | Plate | 2 |
| 12***67 | Pin | 2 |
154-3295 Manifold & Valve Gp
| 15***95 | Manifold & Valve Group | 1 |
| 17***96 | Support As | 1 |
| 17***47 | Support As | 4 |
194-0946 Manifold & Valve Gp -Main Control Valve
| 15***06 | Pump Group-Piston | 1 |
| 15***22 | Pump Group-Gear; -Pilot | 1 |
| 17***18 | Pump Group-Piston; -Fan Motor | 1 |
154-3294 Manifold & Valve Gp
| 09***48 | Nipple, Grease | 2 |
| 11***44 | Plate | 2 |
| 12***67 | Pin | 2 |
194-0947 Manifold & Valve Gp -Main Control Valve
| 15***22 | Pump Group-Gear; -Pilot | 1 |
| 17***18 | Pump Group-Piston; -Fan Motor | 1 |
| 19***47 | Manifold & Valve Group; -Main Control Valve | 1 |
155-9203 Motor & Mtg Gp-Swing
| 15***03 | Motor & Mtg Group-Swing | 1 |
| 15***24 | Pump Group-Gear; -Pilot | 1 |
155-9201 Motor & Mtg Gp-Swing
| 15***46 | Coupling Group-Pump | 1 |
| 15***01 | Motor & Mtg Group-Swing | 1 |
| 15***05 | Pump Group-Main Hydraulic | 1 |
155-9198 Motor & Mtg Gp-Travel
| 09***67 | Washer-Hard; (15x28x2.5-mm Thk) | 4 |
| 09***24 | Bolt; (M14x2x145-mm) | 4 |
| 15***98 | Motor & Mtg Group-Travel | 1 |
200-3252 Motor Gp-Piston
| 10***96 | Seal-O-Ring | 2 |
| 20***52 | Motor Group-Piston; -Reversing Hydraulic Fan | 1 |
| 20***69 | Pump Group-Main Hydraulic | 1 |
209-6058 Motor Gp-Piston -Hydraulic Oil Cooler
| 09***58 | Ring-Retaining | 2 |
| 10***86 | Bolt; (M4x.7x12mm)(M4x0.7x12mm) | 4 |
| 11***30 | Screw; (1-5/16-Thd) | 2 |
247-8978 Motor Gp-Piston -Fan
| 03***28 | Seal-O-Ring | 1 |
| 11***22 | Seal-O-Ring | 1 |
| 15***25 | Bearing As-Roller | 1 |
177-2548 Motor Gp-Swing
| 09***15 | Ring-Retaining | 1 |
| 15***54 | Barrel | 1 |
| 16***40 | Pin | 3 |
155-9204 Motor Gp-Swing
| 09***58 | Ring-Retaining | 2 |
| 11***30 | Screw; (1-5/16-Thd) | 2 |
| 11***16 | Pin | 4 |
155-9202 Motor Gp-Swing
| 09***23 | Plug | 2 |
| 09***65 | Plug, Tapered | 5 |
| 09***87 | Ring, Back-Up; (Buck Up) | 2 |
209-5895 Motor Gp-Travel
| 16***78 | Bearing-Spherical | 1 |
| 16***79 | Pin | 3 |
| 16***82 | Washer; (42-mm Odx2.7-mm Thk) | 1 |
9u-1373 Mounting Gp-Cylinder -Bottom Dump
| 15***12 | Piston Assem. | 9 |
| 15***15 | Plate | 1 |
| 15***16 | Guide; (Ball) | 1 |
241-6653 Mounting Gp-Cylinder -Bucket
| 16***66 | Barrel As | 1 |
| 16***59 | Retainer | 1 |
| 16***60 | Guide-Ball | 1 |
187-7089 Mounting Gp-Valve
| 16***59 | Retainer | 1 |
| 16***60 | Guide-Ball | 1 |
| 16***61 | Shim; (0.5-mm Thk) | 1 |
151-6647 Pump & Mtg Gp-Hydraulic
| 09***29 | Ring; (Retaining) | 1 |
| 10***66 | Seal-O-Ring | 1 |
| 12***49 | Seal-Shaft | 2 |
151-6645 Pump & Mtg Gp-Main Hydraulic
| 09***29 | Ring; (Retaining) | 1 |
| 15***45 | Pump & Mtg Group-Main Hydraulic | 1 |
| 16***54 | Swashplate | 1 |
155-9224 Pump Gp-Gear
| 15***24 | Pump Group-Gear; -Pilot | 1 |
| 4J***21 | Packing,Preformed Tube Assembly Flange | 5 |
| 4J***40 | Seal-O-Ring (Id=18.64mm) | 1 |
155-9222 Pump Gp-Gear -Pilot
| 15***22 | Pump Group-Gear; -Pilot | 1 |
| 7Y***28 | Rotor (Casting) | 1 |
| 7Y***30 | Rotor Group-Swivel | 1 |
155-9205 Pump Gp-Main Hydraulic
| 09***39 | Spring | 1 |
| 09***41 | Holder, Guide | 1 |
| 15***05 | Pump Group-Main Hydraulic | 1 |
200-3269 Pump Gp-Main Hydraulic
| 09***33 | Seal-O-Ring (Id=139.60mm) | 3 |
| 09***28 | Seal-O-Ring | 1 |
| 15***19 | Seal | 5 |
155-9206 Pump Gp-Piston
| 09***08 | Seal-O-Ring (Id=44.70mm) | 1 |
| 09***35 | Seal-O-Ring (Id=229.30mm) | 2 |
| 10***40 | Sensor Group-Temperature; -Output Transfer Gear Oil | 1 |
170-9918 Pump Gp-Piston -Fan Motor
| 08***06 | Shim (2.0 mm Thick) | 6 |
| 08***07 | Shim (1.0 mm Thick) | 6 |
| 08***09 | Shim (0.4 mm Thick) | 6 |
259-0878 Pump Gp-Piston
| 12***95 | Retainer | 2 |
| 25***78 | Pump Group-Piston | 1 |
| 2K***99 | Seal-Interface Between Inlet Manifold | 1 |
185-0266 Rotating Gp-Motor
| 11***62 | Spring | 1 |
| 11***64 | Plug; (7/8) | 1 |
| 11***65 | Valve | 1 |
185-0275 Rotating Gp-Motor
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 18***75 | Rotating Group-Motor; -Hydraulic Fan | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
170-9812 Rotating Gp-Pump
| 15***61 | Cover | 1 |
| 15***63 | Cover | 1 |
| 17***12 | Rotating Group-Pump | 1 |
165-9358 Rotating Gp-Pump
| 15***62 | Flange | 1 |
| 15***63 | Cover | 1 |
| 16***58 | Rotating Group-Pump | 1 |
266-7894 Rotating Gp-Pump
| 12***94 | Valve Group-Check; -Tank Port Makeup | 1 |
| 14***44 | Plug As | 3 |
| 14***76 | Body-Valve | 1 |
155-9135 Rotating Gp-Pump
| 11***62 | Spring | 1 |
| 11***64 | Plug; (7/8) | 1 |
| 11***65 | Valve | 1 |
191-5590 Rotating Gp-Pump
| 00***03 | Seal-O-Ring | 2 |
| 14***88 | Cover | 1 |
| 14***92 | Retainer-Spring | 2 |
259-0816 Rotating Gp-Pump
| 22***87 | Valve Group-Control; -Neutral Bypass | 1 |
| 23***99 | Valve Group-Control; -Neutral Bypass | 1 |
| 25***84 | Valve Group-Control; -Neutral Bypass | 1 |
7y-4827 Rotor Gp-Swivel
| 00***64 | Plug | 1 |
| 10***11 | Piston | 3 |
| 10***40 | Plug-Orifice | 2 |
7y-4830 Rotor Gp-Swivel
| 00***64 | Plug | 1 |
| 10***11 | Piston | 3 |
| 14***87 | Valve Group-Control; -Neutral Bypass | 1 |
155-9235 Screen Gp-Hydraulic -Tank
| 00***64 | Plug | 1 |
| 10***11 | Piston | 3 |
| 14***87 | Valve Group-Control; -Neutral Bypass | 1 |
156-0622 Swivel Gp
| 00***64 | Plug | 1 |
| 10***11 | Piston | 3 |
| 10***40 | Plug-Orifice | 2 |
201-1770 Tank & Filter Gp-Hydraulic
| 00***03 | Seal-O-Ring | 2 |
| 09***87 | Seal-O-Ring (Id=20.80mm) | 1 |
| 09***86 | Ring-Back Up; (Backup) | 1 |
168-9369 Tank & Mtg Gp-Hydraulic
| 00***03 | Seal-O-Ring | 2 |
| 14***88 | Cover | 1 |
| 14***92 | Retainer-Spring | 2 |
201-9381 Valve Gp-Check
| 09***68 | Plug, Tapered | 1 |
| 09***82 | Seal-O-Ring (Id=13.80mm) | 1 |
| 09***92 | Seal-O-Ring (Id=23.70mm) | 1 |
173-3429 Valve Gp-Check
| 11***69 | Valve Group-Relief; -Low Signal Pressure | 1 |
| 11***70 | Valve Group-Relief; -High Signal Pressure | 1 |
| 11***65 | Filter; (Edge) | 1 |
127-8394 Valve Gp-Check
| 00***03 | Seal-O-Ring | 2 |
| 09***87 | Seal-O-Ring (Id=20.80mm) | 1 |
| 09***86 | Ring-Back Up; (Backup) | 1 |
201-9382 Valve Gp-Check
| 19***64 | Valve Group-Control | 1 |
| 20***82 | Valve Group-Check; -Return | 1 |
| 30***41 | Ring-Backup | 1 |
156-5783 Valve Gp-Check -Fuel
| 11***69 | Valve Group-Relief; -Low Signal Pressure | 1 |
| 11***70 | Valve Group-Relief; -High Signal Pressure | 1 |
| 11***65 | Filter; (Edge) | 1 |
147-4312 Valve Gp-Check
| 14***81 | Block | 1 |
| 14***29 | Cover | 1 |
| 14***12 | Valve Group-Check | 1 |
234-6899 Valve Gp-Control -Neutral Bypass
| 15***50 | Spacer; (0.16-mm Thk) | 1 |
| 16***02 | Plug | 1 |
| 16***03 | Valve | 1 |
225-6287 Valve Gp-Control -Neutral Bypass
| 11***54 | Valve | 1 |
| 11***37 | Screen As | 1 |
| 11***72 | Body As | 1 |
188-2681 Valve Gp-Control
| 11***97 | Valve Group-Pump Control; -Pressure Compensator | 1 |
| 18***81 | Valve Group-Control | 1 |
| 20***30 | Valve Group-Pump Control; -Flow Compensator | 1 |
223-7736 Valve Gp-Control
| 03***53 | Seal-O-Ring; (08.92mm Id) | 2 |
| 03***43 | Seal-O-Ring | 1 |
| 13***89 | Plug | 1 |
144-7087 Valve Gp-Control -Neutral Bypass
| 09***52 | Seat, Spring | 1 |
| 09***74 | Seal-O-Ring (Id=6.8mm); (Id=6.80mm) | 5 |
| 09***86 | Seal - O-Ring (19.80 mm Id) | 2 |
188-2684 Valve Gp-Control
| 10***28 | Piston-Compensator | 1 |
| 10***29 | Case | 1 |
| 10***31 | Cover | 1 |
174-1858 Valve Gp-Control
| 10***11 | Retainer | 1 |
| 11***17 | Seal-O-Ring | 1 |
| 15***72 | Bolt-Socket Head; (M4x0.07-Thd) | 0 |
223-7744 Valve Gp-Control -Rh
| 11***54 | Valve | 1 |
| 11***37 | Screen As | 1 |
| 11***72 | Body As | 1 |
257-7284 Valve Gp-Control -Neutral Bypass
| 11***75 | Ring-Backup (24.92mm Id) | 1 |
| 25***84 | Valve Group-Control; -Neutral Bypass | 1 |
| 2P***75 | Seal-O-Ring | 1 |
145-7181 Valve Gp-Load Control
| 11***75 | Ring-Backup (24.92mm Id) | 1 |
| 14***81 | Valve Group-Load Control; -Boom Lowering-Drift Reduction, Var Adj Boom | 1 |
| 2P***75 | Seal-O-Ring | 1 |
188-2657 Valve Gp-Main Control
| 09***98 | Seal-O-Ring (Id=29.40mm) | 1 |
| 16***65 | Ring-Back Up; (Backup) | 1 |
| 18***57 | Valve Group-Main Control | 1 |
223-7749 Valve Gp-Main Control
| 09***98 | Seal-O-Ring (Id=29.40mm) | 1 |
| 16***65 | Ring-Back Up; (Backup) | 1 |
| 22***49 | Valve Group-Main Control | 1 |
140-0736 Valve Gp-Manifold & Reducing
| 09***68 | Bolt-Socket Head; (M5x0.8x8-mm) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***25 | Lever | 1 |
193-1665 Valve Gp-Pressure Reducing
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
| 14***05 | Ring-Backup | 2 |
204-2730 Valve Gp-Pump Control -Flow Compensator
| 09***86 | Seal - O-Ring (19.80 mm Id) | 1 |
| 09***50 | Seal-O-Ring (Id=10.82mm) | 1 |
| 09***51 | Seal-O-Ring (Id=14.00mm) | 1 |
111-9997 Valve Gp-Pump Control -Pressure Compensator
| 11***97 | Valve Group-Pump Control; -Pressure Compensator | 1 |
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
209-5937 Valve Gp-Pump Control -Pressure Compensator
| 12***91 | Valve Group-Solenoid; -Hydraulic Activation Control | 1 |
| 13***39 | Orifice | 1 |
| 20***37 | Valve Group-Pump Control; -Pressure Compensator | 1 |
200-3270 Valve Gp-Pump Control -Pressure, Flow Compensator
| 09***86 | Seal - O-Ring (19.80 mm Id) | 1 |
| 09***50 | Seal-O-Ring (Id=10.82mm) | 1 |
| 09***51 | Seal-O-Ring (Id=14.00mm) | 1 |
165-9251 Valve Gp-Pump Control
| 10***14 | Bushing | 1 |
| 13***80 | Valve-Shuttle | 1 |
| 16***51 | Valve Group-Pump Control | 1 |
165-9250 Valve Gp-Pump Control
| 11***37 | Valve | 1 |
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
177-2552 Valve Gp-Relief
| 17***52 | Valve Group-Relief | 1 |
| 18***61 | Stick & Bearing As | 1 |
| 18***87 | Pin | 1 |
352-6869 Valve Gp-Relief
| 10***81 | Edge-Segment; (Lh) | 2 |
| 10***82 | Edge-Segment; (Rh) | 2 |
| 12***00 | Protector-Side Bar | 2 |
177-2549 Valve Gp-Relief
| 08***66 | Hose As; (L=850mm) | 5 |
| 10***09 | Connector As | 4 |
| 10***10 | Connector As | 27 |
117-5269 Valve Gp-Relief
| 07***41 | Seal; (30.3mm Od) | 1 |
| 09***11 | Pin; (Spring) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
155-4846 Valve Gp-Relief
| 09***80 | Bolt-Socket Head; (M12x1.75x105-mm) | 8 |
| 09***79 | Seal-O-Ring (Id=10.80mm) | 1 |
| 09***03 | Seal-O-Ring (Id=44.40mm) | 2 |
352-6870 Valve Gp-Relief
| 10***81 | Edge-Segment; (Lh) | 2 |
| 10***82 | Edge-Segment; (Rh) | 2 |
| 12***00 | Protector-Side Bar | 2 |
160-8734 Valve Gp-Relief
| 11***50 | Seal - Lip Type | 4 |
| 16***34 | Valve Group-Relief | 1 |
| 18***58 | Boom & Bearing As | 1 |
117-5270 Valve Gp-Relief
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 11***70 | Valve Group-Relief; -High Signal Pressure | 1 |
144-7113 Valve Gp-Relief
| 09***02 | Ring | 2 |
| 09***76 | Seal-O-Ring | 1 |
| 09***86 | Seal - O-Ring (19.80 mm Id) | 2 |
158-8171 Valve Gp-Shutoff -Hydraulic Pump, Tank
| 10***81 | Edge-Segment; (Lh) | 2 |
| 10***82 | Edge-Segment; (Rh) | 2 |
| 12***00 | Protector-Side Bar | 2 |
6e-4429 Valve Gp-Shuttle
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
| 21***57 | Bucket Group-Front Shovel | 1 |
4t-1860 Valve Gp-Shuttle
| 10***81 | Edge-Segment; (Lh) | 2 |
| 10***82 | Edge-Segment; (Rh) | 2 |
| 12***00 | Protector-Side Bar | 2 |
111-0336 Valve Gp-Shuttle
| 11***36 | Valve Group-Shuttle | 1 |
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
158-9105 Valve Gp-Shuttle
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 15***05 | Valve Group-Shuttle | 1 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
121-1491 Valve Gp-Solenoid
| 12***91 | Valve Group-Solenoid; -Hydraulic Activation Control | 1 |
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
137-3713 Valve Gp-Solenoid
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 13***13 | Valve Group-Solenoid | 1 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
154-6591 Valve Gp-Solenoid
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 15***91 | Valve Group-Solenoid | 1 |
| 23***08 | Lines Group-Bucket; -Bottom Dump | 1 |
111-9916 Valve Gp-Solenoid
| 11***16 | Valve Group-Solenoid; -Grapple Signal-Ground Saw, Grapple Control | 1 |
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 18***73 | Lines Group-Bucket; -Bottom Dump | 1 |
171-3685 Valve Gp-Solenoid
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 17***85 | Valve Group-Solenoid | 1 |
| 23***08 | Lines Group-Bucket; -Bottom Dump | 1 |
116-3420 Valve Gp-Swing Cushion -Anti-Reaction, Fine Swing
| 11***20 | Valve Group-Swing Cushion; -Anti-Reaction, Fine Swing | 1 |
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 23***08 | Lines Group-Bucket; -Bottom Dump | 1 |
155-9200 Valve Gp-Travel Counterbalance
| 12***12 | Cylinder & Seal Group-Bucket | 2 |
| 13***55 | Setscrew; (M4x0.7x8-mm) | 2 |
| 15***00 | Valve Group-Travel Counterbalance | 1 |
Implements
184-5557 Boom Gp
| 12***66 | Bearing-Sleeve | 4 |
| 15***38 | Bowl & Bearing As-Bucket | 1 |
| 16***90 | Deflector | 2 |
184-5562 Lines Gp-Grease
| 12***66 | Bearing-Sleeve | 4 |
| 15***38 | Bowl & Bearing As-Bucket | 1 |
| 16***90 | Deflector | 2 |
184-5559 Stick Gp
| 12***66 | Bearing-Sleeve | 4 |
| 12***44 | Plate | 1 |
| 16***90 | Deflector | 2 |
Lubrication System
200-0655 Base Gp-Oil Filter -Engine
| 03***55 | Tee-Flared | 1 |
| 03***94 | Connector-Flared | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
200-0654 Base Gp-Oil Filter
| 03***55 | Tee-Flared | 1 |
| 03***94 | Connector-Flared | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 3 |
176-1363 Base Gp-Oil Filter -Engine
| 11***68 | Seal-O-Ring; (15.54mm Id) | 1 |
| 16***70 | Plug | 3 |
| 17***63 | Base Group-Oil Filter; -Engine | 1 |
4n-2481 Fastener Gp-Oil Pump Mounting
| 00***73 | Connector-Hose | 1 |
| 09***90 | Clamp; (Hose) (26-39mm Id) | 1 |
| 4N***81 | Fastener Group-Oil Pump Mounting; Oil Pump Mounting Fastener Group | 1 |
178-3326 Filler Gp-Engine Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 2 |
| 10***44 | Elbow | 1 |
200-0653 Filter Gp-Engine Oil
| 03***64 | Hose As | 1 |
| 1P***19 | Coupler (Use With .75 In Hose) | 1 |
| 20***53 | Filter Group-Engine Oil | 1 |
187-3477 Fumes Disposal Gp
| 03***64 | Hose As | 1 |
| 14***81 | Spacer; (13.5x25x12-mm Thk) | 1 |
| 18***77 | Fumes Disposal Group | 1 |
190-2471 Gauge Gp-Oil Level (Dipstick)
| 16***79 | Shaft As-Pump | 1 |
| 16***82 | Shaft As-Pump | 1 |
| 19***71 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
190-2472 Guide Gp-Oil Level Gauge
| 13***82 | Bolt; (M16x2x100-mm) | 2 |
| 13***33 | Adapter-Fan | 1 |
| 13***53 | Lockwasher | 1 |
160-6894 Lines Gp-Engine Oil
| 13***82 | Bolt; (M16x2x100-mm) | 2 |
| 13***33 | Adapter-Fan | 1 |
| 13***53 | Lockwasher | 1 |
151-6662 Lines Gp-Engine Oil Drain
| 15***62 | Lines Group-Engine Oil Drain | 1 |
| 5P***38 | Adapter-O-Ring | 1 |
| 6V***09 | Seal-O-Ring (Id=16.36mm); (16.36-mm Id) | 1 |
187-6659 Lines Gp-Turbocharger Oil
| 01***24 | Bushing To Supply Port | 1 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 5 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 3 |
170-3562 Mounting Gp-Oil Level Gauge
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 12***05 | Elbow | 1 |
201-3825 Oil Change Gp-High Speed
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 8 |
| 17***64 | Spacer; (11x19x11.5-mm Thk) | 1 |
198-1508 Pump Gp-Engine Oil
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***30 | Bearing As-Roller | 1 |
| 12***17 | Seal Group; (Water Pump) | 1 |
Machine Arrangement
176-0501 Chassis Ar
| 13***76 | Mirror Group-Rear View; -Rh | 1 |
| 14***01 | Horn Group-Electric | 1 |
| 15***33 | Lighting Group-Chassis; -Front | 1 |
176-0500 General Ar
| 17***00 | General Ar | 1 |
| 17***01 | Chassis Ar | 1 |
| 17***02 | Frame Ar-Undercarriage | 1 |
176-0508 Shovel Ar-Front
| 10***84 | Cylinder & Seal Group-Bucket | 2 |
| 17***08 | Shovel Ar-Front | 1 |
| 18***57 | Boom Group | 1 |
Operator Station
204-8683 Air Conditioner & Mounting Gp
| 11***58 | Plate | 2 |
| 12***87 | Socket-Auxiliary Power; (12-Volt, 7-Ampere) | 1 |
| 13***65 | Cover; (Door) | 1 |
207-0408 Air Conditioner Ar
| 11***52 | Kit-Window Repair; (Slow Polymerisation) | 1 |
| 11***53 | Kit-Window Repair; (Speedy Polymerisation) | 1 |
| 13***22 | Door Group-Cab | 1 |
220-0171 Air Conditioner Gp
| 19***40 | Support As | 1 |
| 20***39 | Condenser As | 1 |
| 22***71 | Air Conditioner Group | 1 |
205-4518 Air Conditioner Gp
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 14***83 | Plate | 1 |
152-5085 Air Conditioner Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***85 | Air Conditioner Group | 1 |
| 31***18 | Valve As-Pressure Relief; (Refrigerant Compressor) | 1 |
159-4540 Box As-Storage
| 11***13 | Support | 1 |
| 11***16 | Cover | 1 |
| 11***57 | Support Assem. | 1 |
170-2808 Box Gp-Storage
| 11***16 | Cover | 1 |
| 11***57 | Support Assem. | 1 |
| 11***67 | Cover | 1 |
240-2881 Cab Ar -High Resistance Windshield
| 11***79 | Console Group-Operator; -Lh | 1 |
| 11***80 | Console Group-Operator; -Rh | 1 |
| 11***24 | Film-Instruction | 1 |
240-2878 Cab Ar -2-Piece Windshield
| 11***12 | Support | 1 |
| 11***14 | Panel | 1 |
| 11***56 | Support Assem. | 1 |
164-2269 Cab Gp
| 09***31 | Nut; (M12x1.75-Thd) | 2 |
| 09***32 | Knob; (Lh Travel Lever) | 1 |
| 09***33 | Knob; (Rh Travel Lever) | 1 |
164-2271 Cab Gp
| 09***35 | Screw; (Machine) (M5x0.8x8mm) | 2 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***73 | Pin | 1 |
240-2880 Cab Gp
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***41 | Boot | 1 |
| 14***05 | Sensor Group-Position | 1 |
153-3518 Cab Gp
| 14***56 | Control Group-Pedal | 1 |
| 15***18 | Cab Group | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 4 |
153-2912 Cab Gp
| 15***12 | Cab Group | 1 |
| 19***32 | Control Group-Joystick; -Rh | 1 |
| 19***33 | Control Group-Joystick; -Lh | 1 |
164-2268 Cab Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
206-9095 Cab Gp
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***32 | Pin | 1 |
| 17***12 | Control Group-Handle; (Joystick) | 1 |
240-2882 Cab Gp
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***41 | Boot | 1 |
| 14***05 | Sensor Group-Position | 1 |
240-2879 Cab Gp
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***32 | Pin | 1 |
| 17***11 | Control Group-Handle; (Joystick) | 1 |
240-2883 Cab Gp
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***16 | Boot | 1 |
| 24***83 | Cab Group | 1 |
201-7337 Compressor Gp-Refrigerant
| 10***53 | Hose | 1 |
| 10***54 | Nozzle-Air | 1 |
| 10***70 | Grommet | 2 |
163-0872 Compressor Gp-Refrigerant
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 16***72 | Compressor Group-Refrigerant; -Air Conditioner | 1 |
| 16***94 | Control As | 1 |
192-2939 Condenser & Mtg Gp-Refrigerant
| 10***70 | Screw | 2 |
| 11***02 | Washer; (10.2x22.5x3-mm Thk) | 7 |
| 12***58 | Seal; (170cm) | 0 |
111-6280 Console Gp-Operator
| 11***80 | Console Group-Operator; -Rh | 1 |
| 14***50 | Latch Group-Front Window; -Rh | 1 |
| 14***51 | Latch Group-Front Window; -Lh | 1 |
111-6279 Console Gp-Operator
| 11***79 | Console Group-Operator; -Lh | 1 |
| 13***66 | Duct | 1 |
| 13***18 | Duct | 1 |
164-0536 Console Gp-Operator
| 01***02 | Lockwasher | 2 |
| 09***85 | Locknut; (M16x2-Thd) | 2 |
| 11***24 | Spring As; (Gas) | 2 |
195-8931 Control & Mtg Gp-Joystick
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 15***84 | Bracket As | 1 |
| 19***31 | Control & Mtg Group-Joystick | 1 |
139-4005 Control & Mtg Gp-Pedal
| 13***05 | Control & Mtg Group-Pedal | 1 |
| 14***48 | Block-Locking; (Rh) | 1 |
| 14***49 | Block-Locking; (Rh) | 1 |
150-1387 Control Gp-Air & Temperature
| 14***41 | Block-Locking | 1 |
| 14***47 | Block-Locking | 1 |
| 14***50 | Nut | 2 |
111-6308 Control Gp-Handle
| 09***64 | Grommet | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 2 |
217-2317 Control Gp-Heat & Air Cond
| 09***45 | Cable; (Lanyard) | 1 |
| 21***17 | Control Group-Heat & Air Cond | 1 |
| 5P***58 | Sleeve; (Cable Splice) | 2 |
180-8007 Control Gp-Heat & Air Cond
| 12***05 | Joint | 2 |
| 13***35 | Hose | 2 |
| 14***95 | Guard; (266-cm) | 0 |
147-4789 Control Gp-Hydraulic Pedal
| 14***89 | Control Group-Hydraulic Pedal | 1 |
| 17***27 | Support As | 1 |
| 19***96 | Bracket As | 1 |
195-8933 Control Gp-Joystick -Lh
| 09***63 | Grommet | 1 |
| 12***59 | Grommet | 1 |
| 15***20 | Platform As | 1 |
195-8932 Control Gp-Joystick -Rh
| 12***50 | Film-Instruction; (Travel Controls) | 1 |
| 14***89 | Control Group-Hydraulic Pedal | 1 |
| 19***32 | Control Group-Joystick; -Rh | 1 |
187-9905 Control Gp-Joystick -Lh
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***66 | Bezel | 2 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
187-9906 Control Gp-Joystick -Rh
| 11***81 | Support Group-Seat | 1 |
| 11***08 | Control Group-Handle | 1 |
| 12***25 | Seat Group | 1 |
145-3056 Control Gp-Pedal
| 09***43 | Pin-Cotter | 1 |
| 09***80 | Pin; (Clevis) | 1 |
| 13***73 | Bolt As; (M12x1.75x25-mm) | 17 |
169-0489 Control Gp-Unprgmed Monitor
| 16***89 | Control Group-Unprgmed Monitor; -Vims | 1 |
| 21***82 | Harness As-Radio | 1 |
| 22***67 | Button | 1 |
153-2913 Cover Gp-Wiper Motor
| 15***13 | Cover Group-Wiper Motor | 1 |
| 21***88 | Radio Group; -Am/Fm | 1 |
| 21***04 | Speaker | 2 |
133-0022 Door Gp-Cab
| 12***12 | Bonnet; (Rain) | 1 |
| 13***22 | Door Group-Cab | 1 |
| 20***69 | Riser Group-Cab | 1 |
124-0254 Duct Gp-Air
| 11***71 | Boss | 6 |
| 11***10 | Shim; (0.6-mm Thk) | 6 |
| 11***11 | Shim; (1.2-mm Thk) | 6 |
159-9912 Duct Gp-Defroster
| 15***12 | Duct Group-Defroster | 1 |
| 18***70 | Suspension Group-Seat | 1 |
| 20***34 | Suspension Group-Seat; -Air | 1 |
138-8278 Frame Gp-Upper Front Window
| 13***78 | Frame Group-Upper Front Window | 1 |
| 8S***34 | Locknut; (Flange) (7/16-20 Thd) | 1 |
| 8S***24 | Bolt 57.15 mm(2.25 In.) Long | 1 |
126-3162 Guard Gp-Overhead
| 11***50 | Screw-Flat Head; (M8x1.25x60-mm)(M8x1.25 Thd) | 4 |
| 12***62 | Guard Group-Overhead | 1 |
| 13***24 | Kit-Handle Adjuster; (Seat) | 1 |
146-6701 Horn Gp-Electric
| 11***50 | Screw-Flat Head; (M8x1.25x60-mm)(M8x1.25 Thd) | 4 |
| 13***24 | Kit-Handle Adjuster; (Seat) | 1 |
| 13***27 | Seat As-Heater | 1 |
142-1251 Latch Gp-Front Window -Lh
| 11***83 | Switch As-Rocker; (Seat Heater) | 1 |
| 11***58 | Seat Group | 1 |
| 11***73 | Connector; (Receptacle) | 1 |
142-1250 Latch Gp-Front Window -Rh
| 09***27 | Lockwasher-Tooth; (0.6mm Thk) | 2 |
| 09***45 | Cable; (Lanyard) | 1 |
| 11***33 | Seat Group | 1 |
205-4517 Lines Gp-Air Conditioner
| 16***89 | Control Group-Unprgmed Monitor; -Vims | 1 |
| 20***17 | Lines Group-Air Conditioner | 1 |
| 22***70 | Software Group-Monitor; (Vids) | 1 |
205-7517 Lines Gp-Heater
| 13***14 | Support As; (Seat) | 1 |
| 20***17 | Lines Group-Heater | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 4 |
7y-0059 Literature Gp
| 11***66 | Kit-Stop; (Seat) | 1 |
| 12***04 | Plate | 2 |
| 13***21 | Kit-Damper; (Seat) | 1 |
138-5276 Mirror Gp-Rear View
| 12***04 | Plate | 2 |
| 13***28 | Kit; (Cover Clip) (Incls 25 Clips) | 1 |
| 13***39 | Kit-Suspension Cover; (Seat) | 1 |
139-4003 Monitor & Mtg Gp-Operator
| 13***03 | Monitor & Mtg Group-Operator | 1 |
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
206-7077 Operator Ar
| 11***78 | Roller Blind As | 1 |
| 11***88 | Hook | 8 |
| 11***89 | Screw | 16 |
144-9676 Pedal Ar-Third
| 14***76 | Pedal Ar-Third | 1 |
| 3E***68 | Trim-Bulk (131cm) | 0 |
| 4I***49 | Nut-Spacer; (M6x1-Thd) | 6 |
153-2911 Platform Gp-Operator
| 11***20 | Cap | 1 |
| 15***11 | Platform Group-Operator | 1 |
| 5C***40 | Reservoir | 1 |
170-2976 Platform Gp-Operator
| 11***19 | Washer Group-Window | 1 |
| 14***95 | Hose; (650-cm Each) | 0 |
| 17***76 | Platform Group-Operator | 1 |
217-1003 Radio Gp
| 11***91 | Washer | 4 |
| 11***92 | Ring | 2 |
| 11***93 | Bolt-Socket Head; (M8x1.25x40-mm) | 2 |
214-8888 Radio Gp -Am/Fm
| 14***95 | Kit-Catch | 1 |
| 14***03 | Kit-Catch; (Window) | 1 |
| 14***09 | Kit-Seal | 1 |
205-4520 Riser Ar-Cab
| 11***97 | Seal | 1 |
| 12***04 | Brush-Nylon | 1 |
| 13***73 | Housing-Lock; (Upper, Rh) | 1 |
205-1969 Riser Gp-Cab
| 10***22 | Cover As | 1 |
| 11***60 | Nozzle-Water | 1 |
| 13***98 | Motor As; (Window Wiper) (Lower) | 1 |
237-3586 Seat Ar-Suspension
| 10***53 | Hose | 1 |
| 10***54 | Nozzle-Air | 1 |
| 10***70 | Grommet | 2 |
122-9625 Seat Belt Gp -Retractable, 3-In
| 10***12 | Film-Instruction; (Alternate Exit, Remove Window) | 1 |
| 10***42 | Film-Instruction; (Alternate Exit) | 1 |
| 10***53 | Film-Stripe; (Accent Red)(1170-cm) | 0 |
122-4825 Seat Gp
| 11***55 | Film-Air Cleaner (Later Amchines Only) | 1 |
| 12***74 | Film-Notice; (Cylinder Installation) | 6 |
| 12***25 | Seat Group | 1 |
111-6458 Seat Gp
| 11***58 | Seat Group | 1 |
| 11***58 | Film - Air Cleaner (Later Machines Only) | 1 |
| 12***72 | Film-Notice; (Cylinder Installation) | 6 |
130-7340 Seat Gp
| 10***09 | Film-Warning; (Jumper Cables) | 1 |
| 10***03 | Film-Warning; (Travel Control) | 1 |
| 10***39 | Film-Notice; (Engine Start Switch) | 1 |
111-6433 Seat Gp
| 11***33 | Seat Group | 1 |
| 11***17 | Film-Instruction; (Hydraulic System)(Hydraulic Oil Level) | 1 |
| 12***75 | Film-Notice; (Cylinder Installation) | 6 |
221-8771 Service Gp-Monitor
| 12***78 | Film-Notice; (Cylinder Installation) | 6 |
| 13***49 | Film-Notice; (Extended Life Coolant) | 2 |
| 14***11 | Plate-Rops; (Front Guard) | 1 |
111-6281 Support Gp-Seat
| 11***81 | Support Group-Seat | 1 |
| 12***81 | Film-Notice; (Cylinder Installation) | 6 |
| 13***52 | Film-Notice; (Extended Life Coolant) | 2 |
188-7670 Suspension Gp-Seat
| 10***07 | Film-Warning; (Jump Start, Read Omm) | 1 |
| 10***01 | Film-Warning; (Travel Control) | 1 |
| 10***37 | Film-Notice; (Engine Start Switch)(Key Position) | 1 |
124-3926 Suspension Gp-Seat
| 12***73 | Film-Notice; (Cylinder Installation) | 6 |
| 12***26 | Suspension Group-Seat | 1 |
| 13***44 | Film-Notice; (Extended Life Coolant) | 2 |
205-7634 Suspension Gp-Seat -Air
| 12***76 | Film-Notice; (Cylinder Installation) | 6 |
| 13***47 | Film-Notice; (Extended Life Coolant) | 2 |
| 16***27 | Film-Warning; (Universal, Read Omm)(Read Operators Manual) | 1 |
6c-8618 Visor Gp-Protection
| 12***80 | Film-Notice; (Cylinder Installation) | 6 |
| 13***51 | Film-Notice; (Extended Life Coolant) | 2 |
| 16***28 | Film-Warning; (Universal, Read Omm)(Read Operators Manual) | 1 |
6c-8620 Visor Gp-Cab
| 10***08 | Film-Warning; (Jump Start, Read Omm) | 1 |
| 10***02 | Film-Warning; (Travel Control) | 1 |
| 10***38 | Film-Notice; (Engine Start Switch)(Key Position) | 1 |
111-6419 Washer Gp-Window
| 11***42 | Film-Warning; (Travel Control) | 1 |
| 11***44 | Film-Notice; (Engine Start Switch) | 1 |
| 11***19 | Washer Group-Window | 1 |
205-4516 Washer Gp-Window
| 11***61 | Film - Air Cleaner (Later Machines Only) | 1 |
| 12***79 | Film-Notice; (Cylinder Installation) | 6 |
| 13***50 | Film-Notice; (Extended Life Coolant) | 2 |
133-0578 Window Gp-Door
| 10***98 | Film-Instruction; (Hydraulic System)(Front Shovel) | 1 |
| 10***48 | Film-Warning; (Travel Control) | 1 |
| 10***60 | Film-Notice; (Engine Start Switch)(Key Position) | 1 |
137-0182 Window Gp-Front
| 10***12 | Film-Instruction; (Alternate Exit, Remove Window) | 1 |
| 10***42 | Film-Instruction; (Alternate Exit) | 1 |
| 10***53 | Film-Stripe; (Accent Red)(1170-cm) | 0 |
122-4822 Window Gp-Front
| 12***22 | Window Group-Front | 1 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 15***09 | Film-Information; (Air Cleaner) | 1 |
205-4608 Wiper & Washer Gp-Window -Lower
| 20***08 | Wiper & Washer Group-Window; -Lower | 1 |
164-2932 Wiper Gp-Window -Upper
| 16***32 | Wiper Group-Window; -Upper | 1 |
Power Train
199-4661 Drive Gp-Final -Without Motor
| 10***55 | Hinge | 2 |
| 17***81 | Insulation; (325mm X 430mm) | 1 |
| 17***82 | Insulation | 3 |
199-4651 Drive Gp-Final
| 10***48 | Seal; (0.5-M Each) | 0 |
| 19***51 | Drive Group-Final | 1 |
| 20***97 | Insulation | 1 |
199-4662 Final Drive Gp -With Motor
| 11***70 | Pin As | 2 |
| 12***62 | Shim (1.0 mm Thick) | 4 |
| 12***64 | Shim (2.0 mm Thick) | 4 |
199-4653 Final Drive Gp
| 10***48 | Seal; (0.5-M Each) | 1 |
| 18***58 | Sheet-Rubber | 1 |
| 19***53 | Final Drive Group | 1 |
191-2572 Power Train Ar
| 11***70 | Pin As | 2 |
| 12***62 | Shim (1.0 mm Thick) | 4 |
| 12***64 | Shim (2.0 mm Thick) | 4 |
145-3014 Sprocket Gp
| 14***14 | Sprocket Group | 1 |
| 19***91 | Gear & Bearing Group-Swing | 1 |
| 19***98 | Tube As; (Rh) | 1 |
Service Equipment And Supplies
211-7967 Plate & Film Gp
| 21***67 | Plate & Film Group | 1 |
211-7965 Plate & Film Gp
| 21***65 | Plate & Film Group | 1 |
211-7957 Plate & Film Gp
| 21***57 | Plate & Film Group | 1 |
211-7954 Plate & Film Gp
| 21***54 | Plate & Film Group | 1 |
211-7959 Plate & Film Gp
| 21***59 | Plate & Film Group | 1 |
211-7958 Plate & Film Gp
| 21***58 | Plate & Film Group | 1 |
211-7961 Plate & Film Gp
| 21***61 | Plate & Film Group | 1 |
211-7955 Plate & Film Gp
| 21***55 | Plate & Film Group | 1 |
211-7960 Plate & Film Gp
| 21***60 | Plate & Film Group | 1 |
253-4712 Plate & Film Gp
| 25***12 | Plate & Film Group | 1 |
211-7964 Plate & Film Gp
| 21***64 | Plate & Film Group | 1 |
211-7966 Plate & Film Gp
| 21***66 | Plate & Film Group | 1 |
211-7956 Plate & Film Gp
| 21***56 | Plate & Film Group | 1 |
211-7962 Plate & Film Gp
| 21***62 | Plate & Film Group | 1 |
211-7953 Plate & Film Gp
| 21***53 | Plate & Film Group | 1 |
211-7963 Plate & Film Gp
| 21***63 | Plate & Film Group | 1 |
200-8070 Plate & Film Gp
| 20***70 | Plate & Film Group | 1 |
Undercarriage
297-9154 Adjustment Gp-Hydraulic Track
| 10***53 | Bolt; (M30x3.5x150-mm) | 64 |
| 18***65 | Roller Group-Track-Single Flange | 16 |
| 24***66 | Roller Group-Track Carrier | 6 |
168-6743 Adjustment Gp-Hydraulic Track
| 10***53 | Bolt; (M30x3.5x150-mm) | 64 |
| 16***43 | Adjustment Group-Hydraulic Track | 1 |
| 17***74 | Roller Group-Track Carrier | 6 |
176-0502 Frame Ar-Undercarriage
| 17***02 | Frame Ar-Undercarriage | 1 |
| 17***41 | Shaft As-Track | 1 |
| 4H***05 | Packing,Preformed Part Of Kit P/N 4s***42 | 1 |
184-5679 Frame Gp-Undercarriage
| 17***11 | Seal Group-Duo-Cone | 1 |
| 18***79 | Frame Group-Undercarriage | 1 |
| 24***67 | Roller & Bearing As | 1 |
174-8498 Guard Gp-Track Guide
| 16***33 | Rod | 1 |
| 16***34 | Support As | 1 |
| 16***38 | Spring | 1 |
172-3001 Guard Gp-Track Guide -Center
| 17***01 | Guard Group-Track Guide; -Center | 1 |
| 17***00 | Seal-O-Ring | 2 |
| 17***32 | Seal Group-Duo-Cone | 2 |
222-3430 Guard Gp-Track Guide -Full Length
| 17***15 | Link As-Track | 1 |
| 17***17 | Link-Track; (Rh)(Rh) | 47 |
| 17***18 | Link-Track; (Lh)(Lh) | 47 |
186-5655 Guard Gp-Track Guide -Front, Center, Rear
| 16***33 | Rod | 1 |
| 16***34 | Support As | 1 |
| 16***38 | Spring | 1 |
167-9841 Guard Gp-Travel Motor
| 16***41 | Guard Group-Travel Motor | 1 |
| 17***15 | Link As-Track | 1 |
| 17***21 | Bolt-Track | 188 |
194-1157 Idler Gp-Front
| 19***57 | Motor Housing; Assembly, Drive, Motor Housing; Assembly, Drive, Idler Group-Front | 1 |
| 4I***39 | Core | 1 |
| 4I***62 | Cap | 1 |
145-3009 Idler Gp-Front
| 08***75 | Core | 1 |
| 08***76 | Cap | 1 |
| 08***77 | Seal | 1 |
145-3008 Idler Gp-Front
| 14***08 | Idler Group-Front | 1 |
| 16***09 | Support | 1 |
| 16***76 | Accumulator | 1 |
174-0215 Link As-Track
| 15***39 | Piston | 1 |
| 15***41 | Piston | 1 |
| 15***42 | Guide | 1 |
145-3012 Roller Ar-Track & Carrier
| 14***12 | Roller Ar-Track & Carrier | 1 |
| 16***95 | Piston | 1 |
| 16***96 | Rod; (159.2-mm, Oal) | 1 |
242-4066 Roller Gp-Track Carrier
| 13***26 | Bolt; (Shoulder) (M6x1x28.75mm) | 1 |
| 13***28 | Shim; (0.1-mm Thk) | 1 |
| 13***31 | Packing | 1 |
175-3274 Roller Gp-Track Carrier
| 13***26 | Bolt; (Shoulder) (M6x1x28.75mm) | 2 |
| 13***28 | Shim; (0.1-mm Thk) | 2 |
| 13***30 | Plate-Slide | 2 |
300-4611 Roller Gp-Track Carrier
| 13***82 | Bolt; (M16x2x100-mm) | 2 |
| 13***33 | Adapter-Fan | 1 |
| 13***53 | Lockwasher | 1 |
185-5065 Roller Gp-Track-Single Flange
| 13***82 | Bolt; (M16x2x100-mm) | 2 |
| 13***33 | Adapter-Fan | 1 |
| 13***53 | Lockwasher | 1 |
145-3011 Spring Gp-Recoil
| 13***82 | Bolt; (M16x2x100-mm) | 2 |
| 13***33 | Adapter-Fan | 1 |
| 13***77 | Spider As; (8-Blade) | 1 |
239-4379 Spring Gp-Recoil
| 19***36 | Seal | 2 |
| 19***37 | Seal | 2 |
| 19***38 | Support As | 2 |
174-0207 Track Gp
| 17***07 | Track Group | 1 |
| 19***36 | Seal | 2 |
| 19***37 | Seal | 2 |
174-0208 Track Gp
| 17***08 | Track Group | 1 |
| 19***37 | Seal | 2 |
| 21***81 | Seal-O-Ring | 2 |
Work Tools
215-4396 Bowl Gp
| 12***66 | Bearing-Sleeve | 4 |
| 12***44 | Plate | 1 |
| 16***90 | Deflector | 2 |
241-6609 Bowl Gp
| 12***66 | Bearing-Sleeve | 4 |
| 12***44 | Plate | 1 |
| 16***90 | Deflector | 2 |
212-9829 Bowl Gp
| 12***66 | Bearing-Sleeve | 4 |
| 16***90 | Deflector | 2 |
| 17***96 | Plate As | 2 |
241-6626 Bowl Gp
| 12***66 | Bearing-Sleeve | 4 |
| 15***25 | Bowl & Bearing As | 1 |
| 16***90 | Deflector | 2 |
215-4351 Bucket Ar
| 12***66 | Bearing-Sleeve | 4 |
| 16***90 | Deflector | 2 |
| 17***96 | Plate As | 2 |
212-9827 Bucket Ar
| 12***66 | Bearing-Sleeve | 4 |
| 16***90 | Deflector | 2 |
| 17***96 | Plate As | 2 |
210-0656 Bucket Ar
| 09***48 | Nipple, Grease | 4 |
| 12***66 | Bearing-Sleeve | 4 |
| 15***25 | Bowl & Bearing As | 1 |
235-4944 Bucket Ar-Front Shovel -Rock
| 11***08 | Pin-G.E.T. | 1 |
| 11***09 | Retainer As-G.E.T. | 1 |
| 23***44 | Bucket Ar-Front Shovel; -Rock | 1 |
241-6640 Bucket Ar-Front Shovel -Rock, Spill Plate
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***88 | Filter Element-Cab Air; (Air Conditioner/Cab Heater) | 1 |
| 10***89 | Cover | 1 |
206-2440 Bucket Ar-Front Shovel
| 12***66 | Bearing-Sleeve | 4 |
| 16***90 | Deflector | 2 |
| 17***96 | Plate As | 2 |
211-7951 Bucket Ar-Front Shovel
| 12***66 | Bearing-Sleeve | 4 |
| 15***84 | Plate-Wear | 2 |
| 16***90 | Deflector | 2 |
241-6607 Bucket Ar-Front Shovel -Heavy-Duty Rock
| 11***08 | Pin-G.E.T. | 1 |
| 11***09 | Retainer As-G.E.T. | 1 |
| 24***07 | Bucket Ar-Front Shovel; -Heavy-Duty Rock | 1 |
220-1594 Bucket Ar-Front Shovel -Heavy-Duty
| 11***08 | Pin-G.E.T. | 1 |
| 11***09 | Retainer As-G.E.T. | 1 |
| 22***94 | Bucket Ar-Front Shovel; -Heavy-Duty | 1 |
241-6624 Bucket Ar-Front Shovel -Heavy-Duty Rock
| 11***08 | Pin-G.E.T. | 1 |
| 11***09 | Retainer As-G.E.T. | 1 |
| 17***09 | Tip-Penetration; (J-700) | 1 |
220-1595 Bucket Gp-Front Shovel -Heavy-Duty
| 09***43 | Pin-Cotter | 2 |
| 09***14 | Pin, Clevis | 2 |
| 13***55 | Bolt; (M8x1.25x8-mm) | 10 |
215-4352 Bucket Gp-Front Shovel
| 12***45 | Grommet | 2 |
| 12***46 | Seal | 1 |
| 12***47 | Seal | 1 |
206-2441 Bucket Gp-Front Shovel
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***88 | Filter Element-Cab Air; (Air Conditioner/Cab Heater) | 1 |
| 10***89 | Cover | 1 |
241-6608 Bucket Gp-Front Shovel -Heavy-Duty Rock
| 09***27 | Lockwasher-Tooth; (0.6mm Thk) | 6 |
| 10***96 | Bolt-Socket Head; (M10x1.5x50-mm) | 2 |
| 10***27 | Washer; (Flat) | 2 |
241-6641 Bucket Gp-Front Shovel -Rock
| 11***52 | Kit-Window Repair; (Slow Polymerisation) | 1 |
| 11***53 | Kit-Window Repair; (Speedy Polymerisation) | 1 |
| 13***22 | Door Group-Cab | 1 |
212-9828 Bucket Gp-Front Shovel
| 09***92 | Washer, Tooth | 2 |
| 10***26 | Wheel As-Blower | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
210-0657 Bucket Gp-Front Shovel
| 09***92 | Washer, Tooth | 2 |
| 10***26 | Wheel As-Blower | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
241-6625 Bucket Gp-Front Shovel -Heavy-Duty Rock
| 11***52 | Kit-Window Repair; (Slow Polymerisation) | 1 |
| 11***53 | Kit-Window Repair; (Speedy Polymerisation) | 1 |
| 12***22 | Window Group-Front | 1 |
211-7952 Bucket Gp-Front Shovel
| 21***52 | Bucket Group-Front Shovel | 1 |
| 5P***29 | Tube .762 Dm(3 In.) | 21 |
| 8M***73 | Clip; (17.46mm Id)(Hose As To Mag Drive Housing) | 4 |
235-4945 Bucket Gp-Front Shovel -Rock
| 23***45 | Bucket Group-Front Shovel; -Rock | 1 |
| 24***82 | Cab Group | 1 |
6y-6355 Tip Gp-Abrasion -J-700
| 09***27 | Lockwasher-Tooth; (0.6mm Thk) | 6 |
| 10***96 | Bolt-Socket Head; (M10x1.5x50-mm) | 2 |
| 10***39 | Support-Filter | 1 |
6y-6354 Tip Gp-Long -J-700
| 11***58 | Plate | 2 |
| 12***87 | Socket-Auxiliary Power; (12-Volt, 7-Ampere) | 1 |
| 13***65 | Cover; (Door) | 1 |
100-5588 Tip Gp-Long -J-700, Heavy-Duty
| 10***88 | Tip Group-Long; -J-700, Heavy-Duty | 1 |
| 11***58 | Plate | 2 |
| 12***87 | Socket-Auxiliary Power; (12-Volt, 7-Ampere) | 1 |
195-9186 Tip Gp-Penetration Plus -J-700
| 11***58 | Plate | 2 |
| 12***87 | Socket-Auxiliary Power; (12-Volt, 7-Ampere) | 1 |
| 13***65 | Cover; (Door) | 1 |
5090B serial number reference
On the 5090B the Cat Product Identification Number (PIN) plate is riveted to the machine frame, typically on the right side of the cab exterior, with a duplicate engine plate on the 3456 diesel. Machines of this era carry a 17-character PIN, and the machine's serial number is the last eight characters of that string. The first three letters of that eight-character serial (for example CLD or SJY) are the prefix identifying the build series; the digits that follow are the sequential unit number within that series.
| Prefix | Identifies | Notes |
|---|---|---|
| CLD | 5090B Front Shovel | Front-shovel (mass-excavation loading) configuration, the only body style documented for this model. Powered by the Cat 3456 ATAAC diesel (15.8 L, rated about 382 kW / 513 hp at 1800 rpm, electronic unit injectors, ADEM II control). Has its own dedicated disassembly/assembly and parts documentation starting CLD00001-up. Model overall was built roughly 2002-2004; exact calendar-year cutoff for this prefix is not published - confirm with a dealer if the build year matters. |
| SJY | 5090B Front Shovel | Front-shovel configuration, same Cat 3456 ATAAC diesel as the CLD range. Has its own dedicated disassembly/assembly and parts documentation starting SJY00001-up, current in the parts system alongside CLD. Model overall was built roughly 2002-2004; exact calendar-year cutoff not published - confirm with a dealer if the build year matters. |
Frequently asked questions
What engine does the Caterpillar 5090B use?
The 5090B runs Caterpillar's 3456 ATAAC inline-six diesel: 15.8 L displacement, turbocharged, air-to-air aftercooled. Net flywheel power is 382 kW (513 hp) at 1800 rpm. It is the same engine family used in Caterpillar's 385B excavator of the same era, not a smaller or larger 3400-series variant.
What is the operating weight of the Caterpillar 5090B?
Operating weight runs about 91,600 kg (201,900 lb) in standard configuration. Some build configurations land closer to 87,500-87,700 kg (193,000-193,400 lb), depending on bucket size and counterweight. Configuration moves the number, so check the specific machine's spec plate for an exact figure.
What replaced the Caterpillar 5090B?
No confirmed direct successor exists in factory literature. Caterpillar built the 5090B from about 2002 to 2004, and a 2003 deal to sell 5000-series shovel intellectual property to Terex named only the larger 5110B, 5130B, and 5230B models, not the 5090B. That deal fell through in early 2004, and Caterpillar exited large hydraulic mining shovel production as a standalone line for years afterward. Treat the 5090B as an end-of-line model rather than look for a direct nameplate successor.
What 5090B owners discuss
What engine problems come up most often on the 5090B, and are they really engine problems?
The 5090B runs the Cat 3456 ATAAC, a 6-cylinder diesel rated around 382 kW (513 hp) at 1800 rpm. Reported low-power or smoky-running complaints on this engine family trace back to the air-to-air aftercooler (ATAAC) piping far more often than the turbocharger itself. Loose or leaking clamps on the aftercooler ducting bleed off boost before it reaches the cylinders, and show up as soot streaks at the clamp joints. Chasing a turbo swap before pressure-testing the ATAAC piping wastes money on this platform. Confirm the actual cause with a boost-leak test before condemning the turbocharger.
It has three hydraulic pumps - is that setup a known weak point?
The 5090B uses a closed-center, load-sensing circuit (Cat markets it as PPPC): two main variable-displacement piston pumps handle the shovel functions and a separate variable piston pump is dedicated to swing. The architecture itself holds up well when kept clean. Sluggish response, jerky cylinder movement, or overheated oil almost always trace back to filter neglect or fluid contamination rather than a failed pump. The circuit runs several filters across different filtration stages specifically to protect the load-sensing valves, so skipping filter service is the most common self-inflicted failure on this hydraulic layout.
What kind of undercarriage wear should I expect on a shovel like this?
These machines spend their working life on quarry and mine benches rather than finished ground, so rock fines mixed with water or rain create an abrasive slurry that eats bushings, rollers, and idlers faster than a construction excavator logging similar hours. Expect accelerated wear at the pin/bushing joints and roller flanges on any unit that worked wet blast rock or clay-heavy pits. Track tension and roller flat-spotting are the first things worth checking on a used 5090B - undercarriage renewal is typically the largest single line item in a mining-shovel rebuild budget.
The bucket doesn't dig like a normal excavator arm - what actually goes wrong with the bottom-dump mechanism?
The 5090B carries a fixed bottom-dump bucket for loading trucks, not a curl-and-dig backhoe bucket, so its trouble spots are different from a typical excavator. The recurring complaint is the dump door not swinging through full travel, usually from door-stop or trip-scroll settings that drift out of adjustment and keep the door from reaching full opening, trapping material inside. Mud and fines packed into the door hinge pins add drag and slow the swing; if the scrolls are set too tight, the door can slam open hard enough to crack the hinge pins. Check door travel and hinge condition on any used 5090B before assuming a dump-cycle complaint is hydraulic.
What electrical or sensor issues come up on this era of Cat machine?
The 5090B uses Cat's VIDS (Vital Information Display System) - analog gauges, a display, and a keypad - along with a pump-valve electronic controller that manages the load-sensing pumps and auxiliary valve. Across this generation of ADEM-controlled Cat diesels, the recurring field issue is not the control module itself but corroded or loose pins in the sensor connectors, especially where moisture gets into the harness. That produces intermittent fault codes or gauge readings that clear once the connector is cleaned, dried, and reseated. Worth ruling out before chasing a sensor replacement.
Anything to watch on the swing system?
The swing bearing and swing gear on a machine this size need disciplined, regular greasing - daily on machines doing a lot of quick-cycle truck loading - since dust and fines that get past a dry or under-greased bearing accelerate gear-tooth wear. Left unaddressed, swing hesitation, vibration, or uneven rotation torque are the early warning signs of bearing wear or tooth spalling; in the worst case, wear progresses to structural damage in the swing rack. Any noise, roughness, or play in the swing on a used unit is worth a proper bearing-clearance and gear-tooth inspection. Have your dealer verify swing bearing and gear condition before returning the machine to service.
What should I check before buying a used 5090B?
Pull hours and any available oil-sample history first - these machines were built 2002-2004, so most for sale now are well into a second or third ownership in mining or quarry duty, and paper trail matters. Walk the structure looking for cracked or repaired welds on the boom, stick, and main frame, and be wary of fresh paint that could be hiding a repair. Check the bottom-dump door for full travel and hinge-pin condition, cylinder rods for scoring or pitting, and pressure-test the ATAAC piping if the engine seems down on power. Rotate the house and feel for play or noise in the swing bearing and gear. Check undercarriage wear percentage given how abrasive quarry and mining duty is on bushings and rollers. Given the age and application of these machines, have your dealer verify structural integrity (frame, boom, swing bearing) and pull a full fault-code and ECM history before purchase.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 5090B part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.