Caterpillar 428D
Caterpillarbackhoe loader(no series)

Caterpillar 428D

Specifications · fluids and capacities · maintenance intervals

Post a parts request and compare supplier quotes.

The Caterpillar 428D is a four-wheel-drive, wheeled backhoe loader in Cat's D-series lineup, built for general construction, utility, and rental-fleet digging and loading work. It runs a Cat 3054 series turbocharged diesel, marketed as the 3054T, 3054C DIT, or 3054 CT depending on build date and market, a 4-cylinder, 4.4 L engine rated 80 hp (60 kW) net at 2,200 rpm. The engine meets Tier 2 emissions and is mechanically governed through a Stanadyne rotary injection pump, with no engine ECM. Operating weight runs 7,738-7,739 kg (17,025-17,062 lb) depending on configuration. Built roughly 2001-2006, largely at Caterpillar's Leicester (Desford), England backhoe loader plant, the 428D replaced the 428C and was itself replaced by the 428E, which moved to the Cat C4.4 ACERT engine. Caterpillar offered the 428D with a standard or extendable dipperstick, a powershuttle or optional auto-shift transmission, and center-pivot or sideshift backhoe geometry, with standard-duty and reinforced bucket options front and rear.

Across the 428 family, Caterpillar moved from earlier, mechanically simpler engines toward the compact turbocharged 3054 used in the 428C and 428D, then on to the emissions-tiered C4.4 ACERT engine in the 428E and later machines. The D-series sits at the tail end of the fully mechanical fuel-injection era for this model line: no ECM, no aftertreatment, and few electronic sensors to fail, which is a large part of its appeal on the used market today. Parts commonality with siblings like the 416D, 420D, 430D, and 432D, which share the same engine family, transmission, axle, and backhoe linkage design, keeps used parts and rebuild components easier to source than on many newer, electronically controlled backhoe loaders. For buyers who want proven digging and loading performance without emissions-electronics complexity, the 428D remains a common, budget-friendly choice in the used backhoe loader market.

Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.

Caterpillar 428D specifications

Engine

Engine modelCat 3054 series 4-cylinder turbocharged diesel with direct injection (identified across sources as 3054T / 3054C DIT / 3054 CT depending on build era)
Cylinders4, inline
Displacement4.4 L (268 cu in)
Gross power83-85 hp (62-63 kW) at 2200 rpm
Net power80 hp (60 kW) at 2200 rpm
Emissions tierTier 2

Weights

Operating weight (4WD)17,025-17,062 lb (7,738-7,739 kg), minor variance by source/configuration
Maximum gross weight21,560 lb (9,800 kg) fully equipped/ballasted
Shipping weightNot published separately from operating weight for this model
Ground pressureNot published (wheeled machine, tire-mounted)

Dimensions

Transport length18 ft 9 in - 18 ft 11 in (5.71-5.76 m)
Transport width7 ft 10 in - 7 ft 11 in (2.39-2.41 m)
Transport height (cab top)9 ft 6 in - 9 ft 7 in (2.90-2.93 m)
Wheelbase82.7-83 in (2.10 m)
Ground clearance12.6 in (320 mm)
Turning radius17.6 ft (5.36 m)

Performance

Travel speed, standard transmissionPower shuttle, 4 forward/4 reverse, up to 19.7-19.8 mph (31.7-31.9 kph)
Travel speed, optional transmissionAuto-shift, 5 forward/3 reverse, up to 18.2 mph (29.3 kph) forward
Loader lift capacity at full height7,470-7,646 lb (3,388-3,468 kg)
Loader bucket breakout force11,290-11,465 lb (5,132-5,201 kg)
Backhoe bucket digging force12,840 lb (5,824-5,836 kg)
Backhoe max digging depth, standard stick15 ft 11 in - 16 ft (4.85-4.88 m)
Backhoe max digging depth, optional extendable stickapprox. 19 ft 4 in (5.89 m)

Service capacities (summary)

Fuel tank33.8-34.0 gal (128-128.3 L)
Hydraulic system21.0 gal (79 L)
Engine oilapprox. 7.7 qt (7.3 L), refer to dealer service data for exact refill by build
Cooling systemapprox. 15.1 qt (14.3 L), refer to dealer service data for exact refill by build

Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.

428D fluids & capacities

SystemCapacityRecommended fluid
Engine crankcase (with filter)7.3 L (7.7 US qt)Cat DEO (Diesel Engine Oil, meets Cat ECF-1). Engine is the Cat 3054 turbocharged diesel (DIT), four-cylinder. Viscosity by climate: SAE 10W-30 for general service; Cat multigrade 0W-40, 5W-40 or 10W-40 for wide ambient-temperature swings.
Cooling system14.3 L (15.1 US qt)Cat ELC (Extended Life Coolant), factory premix. Organic-acid corrosion-inhibitor formula, no phosphates or silicates, extended drain interval versus conventional antifreeze.
Fuel tank128.7 L (34.0 US gal)Cat-recommended No. 2-D diesel fuel, low-sulfur grade matched to the engine's emissions certification.
Transmission (power shuttle standard, or power shift/autoshift optional)15.0-20.5 L (15.9-21.7 US qt), varies by transmission option/configurationCat TDTO (Transmission and Drive Train Oil, TO-4 spec). Viscosity by climate: TDTO 10W in cold ambient, TDTO 30 in moderate-to-warm ambient, TDTO 50 in hot ambient, or TDTO TMS multi-season blend across a wide range.
Hydraulic tank (reservoir)approx. 49.0 L (12.9 US gal)Cat TDTO (TO-4 spec), same fluid family used in the transmission and final drives on this backhoe loader. Figure is approximate, pending dealer confirmation for the exact configuration.
Hydraulic system (total refill: tank, lines, cylinders)79.0 L (21.0 US gal)Cat TDTO (TO-4 spec). Viscosity graded by climate the same as the transmission: 10W cold, 30 moderate/warm, 50 hot, or TMS multi-season.
Brake system (wet-disc reservoir)0.7 L (0.7 US qt)Cat TDTO 10W (TO-4 spec), shared with the transmission circuit.
Front axle and final drives (MFWD-equipped units)differential housing approx. 11.0 L (11.6 US qt); each wheel-end final drive approx. 0.7 L (0.7 US qt) — approximate, verify against your specific axle configurationCat TDTO 30 (TO-4 spec).
Rear axle and final drivesdifferential housing approx. 24.0 L (25.4 US qt); each wheel-end final drive approx. 1.6 L (1.7 US qt) — approximate, verify against your specific axle configurationCat TDTO 30 (TO-4 spec).
Grease (all pin, bushing and bearing points)spec only, no published per-point volumeCat Multipurpose Grease (Moly, MPGM), NLGI 2, over 3% molybdenum, for medium-load/medium-speed pin and bushing points in low-moisture service. Cat Multipurpose Lithium Grease (MPGL), NLGI 2, for light-duty points needing higher temperature tolerance up to 175 C (350 F).

Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.

Caterpillar 428D maintenance schedule

Service intervalTasks
Every 10 h
  • Check engine oil level, coolant level, and hydraulic oil level before starting
  • Drain water and sediment from the fuel system water separator
  • Lubricate backhoe boom, stick, bucket, and cylinder pins daily
  • Lubricate loader bucket, cylinder, and linkage pins daily
  • Weekly: check tire inflation and wheel nut torque
  • Weekly: lubricate stabilizer and swing frame pivots, and check transmission oil level
Every 250 h
  • Clean or replace axle breathers on front and rear axles
  • Lubricate the rear axle universal joint
  • Inspect, adjust, or replace engine accessory belts
  • Check front and rear differential and final drive oil levels
  • Lubricate rear kingpin bearings
  • Pull an engine oil sample for analysis and inspect extendable stick wear pads if equipped
Every 500 h
  • Change engine oil and filter on the Cat 3054 series diesel
  • Replace the fuel filter and water separator element
  • Replace the hydraulic system oil filter
  • Replace the transmission oil filter and pull a transmission oil sample
  • Lubricate the drive shaft spline
  • Pull coolant, front/rear differential, and front/rear final drive oil samples
Every 1,000 h
  • Check and adjust engine valve lash on the mechanically governed 3054
  • Change front and rear differential oil
  • Change front and rear final drive oil
  • Change transmission oil and clean the transmission magnetic screen
  • Inspect the ROPS structure and mounting hardware
  • Lubricate front wheel bearings
Every 2,000 h
  • Replace the engine crankcase breather
  • Change hydraulic system oil
  • Inspect the turbocharger for shaft play, oil leakage, and boost loss
  • Check Stanadyne injection pump timing and delivery for drift
  • Inspect powershuttle transmission clutch pack engagement and pressure
Every 3,000 h
  • Add Cat ELC coolant extender to restore corrosion inhibitor level
  • Inspect backhoe boom, stick, and loader linkage pins and bushings for wear and replace as needed
  • Inspect wet disc brakes for pad wear and drag
  • Check kingpin tapered roller bearing preload and front axle alignment
Every 6,000 h
  • Change engine coolant (Cat ELC) in full
  • Inspect hydraulic hoses and fittings for age-related deterioration and replace as needed
  • Evaluate transmission clutch packs and torque converter condition for rebuild
  • Inspect cab or ROPS canopy mounts, seat belt, and structural welds

Servicing the 428D beyond the schedule

Predictive Maintenance & Fluid Analysis

The 428D's Cat 3054 turbocharged diesel has no ECM, so there are no fault codes to lean on. Engine, hydraulic, and axle condition depend on scheduled oil sampling instead. Pull engine oil samples at every oil change to track wear metals from the mechanically governed fuel system and turbocharger. Sample hydraulic oil, and front and rear differential and final drive oil, on the same interval. Watch for water in the fuel water separator bowl; the Stanadyne rotary pump is unforgiving of contaminated fuel.

Corrective & Common Repairs

Powershuttle clutch packs are a common driveline complaint on the 428D; slipping or delayed engagement usually traces to worn friction plates or transmission oil that isn't TDTO TO-4. Kingpin tapered roller bearings and backhoe boom, stick, and loader linkage pin-and-bushing sets wear from missed daily greasing and need periodic replacement. Wet disc brakes hold up well but check for drag or uneven stopping. Turbocharger shaft play and injection pump drift on the mechanically governed 3054 show up as smoke or power loss; pump internals need a Stanadyne-trained tech.

Overhaul & Rebuild Points

Check engine valve lash on the 3054 at major service intervals since there's no ECM to compensate for drift; adjust before it affects idle or power. Budget for turbocharger rebuild or replacement and injection pump exchange as the engine passes mid-life hours. Powershuttle transmission clutch packs and the torque converter are the big-ticket driveline rebuild items. On the backhoe end, plan to bush and pin the boom, stick, and dipper linkages, and replace extendable stick wear pads, as they define working slop and cycle-time feel.

Seasonal & Environment Servicing

Before winter, check ELC coolant freeze protection and the glow plug and block heater circuits; the mechanically governed 3054 has no ECM to adjust cold-start fueling, so correct oil viscosity matters more in freezing weather. Drain the fuel water separator more often in wet seasons; the Stanadyne pump is sensitive to water in the fuel. In hot, dusty conditions, clean the radiator and hydraulic cooler fins more often and watch tire pressure. Grease boom, stick, and axle pivot points on schedule; grit accelerates kingpin and bushing wear.

428D common service parts

Part numberPart
131-1812Filter Element As-FuelCheck fitment →
110-6326Filter Element As-AirCheck fitment →
110-6331Filter Element As-AirCheck fitment →
126-1817Filter-OilCheck fitment →
7X-8549Switch As-PressureCheck fitment →

Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.

428D fault codes & troubleshooting

CodeMeaningLikely causeWhat to do
Coolant Temperature warning lamp (red thermometer-in-liquid telltale)Engine coolant has reached or exceeded the high-temperature threshold monitored by the coolant temperature sender.Low coolant level, plugged radiator core, slipping or damaged fan drive/belt, failed thermostat, or a faulty sender/wiring.Reduce load and idle down; shut off if temperature keeps climbing. Once safe, check coolant level, clean the radiator core, and verify fan and thermostat operation before returning to work.
Engine Oil Pressure warning lamp (red oil-can telltale)Oil pressure switch has detected pressure below the safe minimum for the current engine speed.Low oil level, worn oil pump, plugged filter or pickup screen, or a faulty pressure switch/wiring.Shut the engine down immediately. Check oil level and condition, inspect the filter and pressure switch before restarting.
Alternator/Charging System warning lamp (battery telltale)System voltage from the alternator has dropped below the normal charging range; the battery is discharging.Worn or slipping drive belt, failed alternator, loose/corroded battery or ground connections, or a faulty regulator.Check belt tension and battery/ground connections, then test alternator output. Replace or repair as needed.
Parking Brake warning lamp (red P/brake telltale)Signals that the parking brake is still applied.Parking brake lever or switch left engaged, or a faulty parking brake switch/solenoid circuit.Confirm the parking brake control is fully released. If the lamp stays on with the brake released, check the switch and wiring.
Air Filter Restriction indicator (amber filter telltale)Intake air restriction has exceeded the allowable limit, pointing to a clogged primary air filter element.Dirty or clogged air filter element, collapsed/leaking intake hose, or a stuck restriction indicator.Inspect and clean or replace the air filter element and check intake piping for damage before returning to service.
Hydraulic Oil Filter Restriction indicator (amber filter telltale)Return-line hydraulic filter has reached its bypass/restriction threshold.Clogged hydraulic filter element, cold/high-viscosity oil at start-up, or contaminated hydraulic oil.Let hydraulic oil reach operating temperature before judging the lamp; replace the filter element if it stays on once warm, and check oil cleanliness.
Transmission/Torque Converter Oil Temperature warning lamp (red thermometer telltale)Transmission/torque converter oil temperature has exceeded the safe operating range.Low transmission fluid, restricted or dirty transmission oil cooler, sustained high-load or stall-condition operation, or a failing temperature sender.Reduce load and let the machine idle to cool. Check fluid level and cooler airflow before resuming work.
General System Fault lamp (flashing exclamation point telltale)Generic alert that a monitored circuit somewhere in the machine's electrical system is outside normal parameters; it does not point to one specific component.Any sender, switch, or wiring fault feeding the gauge/warning circuits (e.g., a shorted or open sensor circuit).Scan the gauge cluster for which specific telltale is also lit, then troubleshoot that circuit per the electrical system manual; if no other lamp is lit, check connectors and grounds.

Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.

428D attachments & work tools

Backhoe (rear) buckets

Pin-on standard-duty buckets are the base rear tool; typical width range for this size class runs 305-914 mm (12-36 in). The 428D shipped with a 610 mm (24 in) standard-duty bucket as base equipment. Extreme-service, ditch-cleaning, grading, and high-capacity buckets are also offered in this range.

Loader (front) buckets

General-purpose and multi-purpose (4-in-1 clamshell) loader buckets are typical for this class, sized around 1.0-1.35 m3 (35-47 ft3). The 428D's standard loader bucket is about 1.0 m3 (1.35 yd3) and roughly 2260 mm (89 in) wide.

Ground-engaging and demolition work tools

Rear-mount hydraulic hammers/breakers, augers, rippers, vibratory compaction plates or wheels, and cold planers are offered for backhoe loaders in this size class, covering demolition, trenching, compaction, and light paving work.

Material handling and site work tools

Pallet forks, brooms/sweepers, grapples, and material-handling arms or truss booms mount to the loader end (or rear tool carrier) for this class, extending the machine into site cleanup and material-handling roles beyond digging and loading.

Coupler and mounting systems

Pin-on mounting is the base backhoe tool interface. A factory quick-coupler option in the same size range (415-444 backhoe loaders) uses a self-adjusting wedge lock with a secondary independent lock and a visual lock-verification tab, offered in manual or hydraulic-actuated versions; the hydraulic version needs a dedicated factory-installed hydraulic circuit.

Hydraulic kit and arrangement notes

Hydraulically powered rear tools (hammer, auger, hydraulic thumb, hydraulic coupler) require the machine's auxiliary hydraulic circuit. Base hydraulic system on the 428D is a variable-displacement axial-piston pump rated near 163 L/min (43 gpm) at up to 228 bar (3300 psi), with a system reservoir capacity of about 79 L (21 gal); tool sizing should stay within this flow and pressure range.

Extendible stick option

A factory extendible-dipper option is available for added reach where more versatility is needed. It adds roughly 922 mm (3 ft) of digging depth and reach over the standard stick, cutting down on machine repositioning on site.

Factory guarding and configuration options

Documented factory options/configurations for this class include an axle (AWD) guard package, front fender guards, stackable counterweights for adjustable ballast, cab or canopy operator stations, outrigger stabilizers, and 2WD or 4WD (MFWD) drive.

Model catalog

Part Book

Browse by group, subgroup and unit. Part numbers are masked and diagram thumbnails are locked.

Selected unit

112-9689 Air Cleaner Group s/n bnb1-699; bll1-650 Part of 130-1470, 145-5882 Air Cleaner Group an attachment

112-9689 Air Cleaner Group s/n bnb1-699; bll1-650 Part of 130-1470, 145-5882 Air Cleaner Group an attachment is listed in the Air inlet and exhaust system / air cleaner group catalog section.

Group
Air Inlet and Exhaust System
Subgroup
Air Cleaner Group
Unit
112-9689 Air Cleaner Group s/n bnb1-699; bll1-650 Part of 130-1470, 145-5882 Air Cleaner Group an attachment
Reduced catalog diagram for 112-9689 Air Cleaner Group s/n bnb1-699; bll1-650 Part of 130-1470, 145-5882 Air Cleaner Group an attachmentLocked diagram
Reduced catalog thumbnail

Parts in this unit

Catalog descriptions with masked part numbers.

Part numberDescription
11***26Filter element as-air; (primary); spare part 11***26 filter element as-air (Caterpillar)
11***31Filter element as-air; (secondary); spare part 11***31 filter element as-air (Caterpillar)
11***89Air Cleaner Group; spare part 11***89 air cleaner group (Caterpillar)
11***17Valve-dust; (air cleaner); spare part 11***17 valve-dust (Caterpillar)

428D serial number reference

The PIN/serial plate is riveted to the machine frame on the right-hand side, just ahead of the cab step below the loader tower pivot, with a backup stamping in the frame steel itself. Read the first three characters as the serial number prefix, which ties the machine to its model and factory manual series; the following digits are the sequence number of that unit within the prefix block. On machines carrying the full 17-character Product Identification Number, the same 3-letter prefix and sequence make up the last eight characters.

PrefixIdentifies
BLL428D backhoe loader
BMT428D backhoe loader
BNS428D backhoe loader
BXC428D backhoe loader
DSX428D backhoe loader
MBM428D backhoe loader

Frequently asked questions

What engine does the Caterpillar 428D backhoe loader use?

A Cat 3054 series turbocharged diesel, sold as the 3054T, 3054C DIT, or 3054 CT depending on build year and market. It's a 4-cylinder, 4.4 L engine rated 80 hp (60 kW) net at 2,200 rpm, Tier 2 compliant, and mechanically governed through a Stanadyne rotary injection pump with no engine ECM.

What is the operating weight of the Cat 428D?

Operating weight runs 7,738-7,739 kg (17,025-17,062 lb), varying with configuration such as standard vs. extendable stick and tire or counterweight options.

What replaced the Caterpillar 428D backhoe loader?

The Cat 428E replaced the 428D, moving to the Cat C4.4 ACERT engine to meet tighter emissions standards. The 428D itself had succeeded the 428C.

What 428D owners discuss

What engine does the Cat 428D backhoe loader run, and are there any quirks worth knowing?
The 428D uses the Cat 3054C DIT, a direct-injection turbocharged four-cylinder diesel built on the same architecture Caterpillar shares with Perkins 1000-series industrial engines, which is why owners cross-referencing fuel pipes and injection-pump seals sometimes see Perkins part families come up alongside Cat ones. Rated output runs roughly 60-62 kW (80-83 hp) at 2200 rpm, with figures shifting slightly by serial range and the Series II update - varies by configuration. The mechanical injection pump is straightforward to service, but the pump's internal seals and washers are only sold as part of a full pump assembly, not as a standalone kit, so budget accordingly for fuel-system work. Have your dealer verify injection timing and pump calibration after any fuel-system repair.
What transmission and front-axle setup does the 428D use, and is parts sourcing an issue?
The 428D pairs a manual-shift powershift transmission, four speeds forward and reverse, with a 4WD front axle sourced from ZF. Owners report that Caterpillar-branded axle and transmission parts carry a real premium over the same components bought through the original drivetrain manufacturer, and full parts schematics for these assemblies can be hard to track down outside the Cat dealer channel. Independent shops familiar with the platform often cross-reference to the OEM axle and transmission supplier to save on routine driveline parts. Have your dealer verify compatibility before fitting non-Cat-branded drivetrain components.
Why does the loader or backhoe feel sluggish, especially when running multiple functions at once?
The 428D hydraulic circuit is closed-center, load-sensing, and pressure-compensated: each control-valve section carries a resolver that passes the highest load-signal pressure downstream to the pump's compensator, which adds a fixed margin pressure over whatever the largest active load demands. When loader lift or backhoe functions run weak, slow, or bog down with several functions stacked together, the usual culprits are a blocked or leaking resolver passage, a worn or misadjusted compensator or relief valve, a clogged hydraulic filter, or general pump wear dropping standby pressure. Missing or damaged O-rings inside the resolver sections is a documented cause on this control-valve family. Check filter condition and fluid level first, then pressure-test the compensator and resolver network before condemning the pump itself.
What wears out on the front axle, and is kingpin play a real concern on this machine?
Yes. Like other 4WD backhoe-loader axles in this weight class, the 428D's front kingpins depend on a regular greasing interval; skip it and the lower kingpin bearing, a comparatively light-duty design, wears quickly and lets play develop in the steering knuckle. Left unaddressed long enough, the only fix can become a full axle replacement, a cost that can rival a large share of the machine's value. The D-series update is reported to have moved to tapered roller bearings at the kingpin for better alignment and wear life versus earlier designs, but the same greasing discipline still applies. Check for play by rocking the front wheel top-to-bottom with the tire off the ground. Have your dealer verify axle and steering-linkage condition if any play is found.
What electrical or gauge problems come up on the 428D and its D-series siblings?
The 428D shares its wiring and instrument-cluster architecture with the rest of the D-series backhoe-loader lineup, and owners across that family report tachometer, hour-meter, and fuel-gauge failures. Typical causes are a blown inline fuse behind the dash or near the steering column, a corroded fuse holder or connector, or a failed sender, with the instrument cluster itself being a recognized weak point on these machines. Work through fuses and grounds before replacing the cluster on a "gauges gone dead" complaint.
What do long-term owners say about overall reliability and running cost of the 428D?
Community consensus generally treats the 428D as a solid, straightforward machine to own and wrench on, with typical Cat build quality and no shortage of used parts and shops familiar with the platform. The recurring complaint is loader-hydraulics feel on individual machines, slow bucket lift while tilt performs fine, rather than a fleet-wide design flaw, and owners usually trace it back to compensator, resolver, or filter condition rather than the pump itself. On a design this old, how the previous owner kept up with fluids and kingpin greasing matters more than cosmetic condition.
What should a buyer check on a used 428D before making an offer?
Ask for service records first; correct fluid types and consistent maintenance matter heavily on this platform. Run every hydraulic function, loader raise and tilt, backhoe boom, stick, bucket, swing, and stabilizers, together and at low idle to check for the sluggishness described above. Jack the front end and check kingpin and wheel-bearing play, inspect boom, dipper, and stabilizer pins and bushings for slop, and confirm the powershift engages cleanly forward and reverse without hesitation or slipping. Check the injection pump and fuel lines for weeping seals, confirm the gauge cluster and warning lights actually work, and verify the hydraulic system holds standby pressure at idle. Have your dealer verify any structural, hydraulic, or steering-axle finding before committing to a purchase.

Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.

Need a specific 428D part?

Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.

Post a parts request and compare supplier quotes.