Caterpillar 323D SA
Caterpillarexcavator

Caterpillar 323D SA

Specifications · fluids and capacities · maintenance intervals

Post a parts request and compare supplier quotes.

The Cat 323D SA is a 20-25 tonne class crawler hydraulic excavator built around the Cat C6.4 ACERT engine, rated 110 kW (150 hp) net flywheel power at Tier 3/Stage IIIA emissions with no diesel exhaust fluid or particulate filter. Baseline operating weight runs about 24,500 kg (54,013 lb), though actual weight shifts with the boom, stick, counterweight, and undercarriage chosen for the job. The SA designation sits inside Caterpillar's broader 323D medium-excavator generation, produced through the mid-to-late 2000s and into the early 2010s alongside the standard 323D, long-reach 323D L, long-and-narrow 323D LN, and short-tail 323D S. It followed the C-series 323 that came before it and was eventually succeeded within the Cat lineup by the 323E and 323F generations. Cat offered the 323D SA with two boom types and three stick lengths, a grease-lubricated undercarriage, and a range of factory work-tool couplers so dealers could configure one base machine for digging, loading, demolition, or utility work.

Where the 323D SA differs from its 323D siblings is configuration, not core drivetrain: it carries the same C6.4 ACERT engine and swing/travel architecture as the wider family but is built to a distinct regional or dealer-order specification under its own PIN prefix, rather than being defined by reach or track width like the L, LN, and S variants. Across the D-series run Caterpillar refined hydraulic control valve and electronic control module calibrations, cab ergonomics, and boom-float features without changing the base engine or chassis. In the used and parts market today the 323D SA holds value because it predates DEF-based aftertreatment: the C6.4 ACERT meets Tier 3/Stage IIIA through in-cylinder combustion control alone, which appeals to buyers who want to avoid selective catalytic reduction and diesel particulate filter service. It also shares major driveline, hydraulic, and undercarriage components with the wider 320D/323D platform, so parts and service expertise stay easy to source even as Cat has moved on to later 323 generations.

Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.

Caterpillar 323D SA specifications

Engine

Engine modelCat C6.4 ACERT, turbocharged diesel
Net power (ISO 9249 / EEC 80/1269)110 kW (150 hp)
Displacement6.4 L (390.6 in³)
Cylinders6, inline
Bore x stroke102 mm x 130 mm (4.02 in x 5.12 in)
Emissions tierTier 3 / Stage IIIA equivalent

Weights

Operating weight24,500 kg (54,013 lb)

Dimensions

Transport width2,390 mm (94.1 in)
Track width, over tracks2,500 mm (98.4 in)
Counterweight ground clearance1,090 mm (42.9 in)

Performance

Max vertical wall digging depth6.80 m (22 ft 4 in)
Max drawbar pull206 kN (46,311 lbf)
Max travel speed5.5 km/h (3.4 mph)

Forces

Bucket / stick digging forceNot published for this configuration in factory documentation reviewed. Confirm with your dealer for the exact boom, stick, and bucket combination.

Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.

323D SA fluids & capacities

SystemCapacityRecommended fluid
Engine crankcase (with filter)30 L (7.9 gal US)Cat DEO or Cat DEO-ULS diesel engine oil. Multigrade viscosity is picked by ambient temperature - SAE 15W-40 covers most moderate climates, while SAE 10W-30 or 0W-40 suit cold starts down to roughly -18°C (0°F). Check the viscosity-by-temperature chart in the machine fluids guide against the coldest expected start-up temperature before topping off.
Cooling system25 L (6.6 gal US)Cat ELC (Extended Life Coolant), a premixed ethylene-glycol/OAT formulation, is the factory fill and preferred refill; rated for up to 12,000 hours or about 6 years before an extender or full change is due. Cat DEAC (conventional coolant) is an acceptable alternative but needs periodic supplemental coolant additive (SCA) top-up. Never mix ELC and DEAC in the same system.
Fuel tank410 L (108 gal US)Ultra-low sulfur diesel (ULSD, 15 ppm sulfur or less). Biodiesel blends up to B20 are acceptable per Cat guidelines; higher blends need dealer sign-off.
Hydraulic system total260 L (68.7 gal US)Cat HYDO Advanced multigrade hydraulic oil. Grade is selected by ambient temperature - a lighter grade (HYDO Advanced 10) for cold climates, heavier grades (30/46) for warm climates. Cat Bio HYDO is a biodegradable alternative for environmentally sensitive worksites.
Hydraulic tank120 L (31.7 gal US)Same Cat HYDO Advanced fill as the hydraulic system total; the tank is the reservoir portion of that same circuit, so grade selection follows the same ambient-temperature guidance.
Final drive (each)10 L (2.6 gal US) per sideCat TDTO (Transmission/Drive Train Oil), SAE 30 or 10W depending on climate, or Cat TDTO-TMS multiseason blend to avoid a seasonal oil change across a wider ambient range.
Swing drive8 L (2.1 gal US)Cat TDTO or Cat TDTO-TMS, the same drivetrain-oil family used in the final drives.
Grease (spec only)Not a fixed-volume compartment - applied at track pins, bucket linkage pins, and the swing bearing per the lubrication chartCat Multipurpose Grease (NLGI Grade 2, lithium-complex EP) for routine greasing points; Cat Extreme Application Grease-2 for severe-duty or high-load pins. Usable roughly -35°C to 40°C (-31°F to 104°F). Track links are factory grease-lubricated (GLT2) and are sealed, not a routine grease point.

Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.

Caterpillar 323D SA maintenance schedule

Service intervalTasks
Every 10 h
  • Check engine oil, coolant, and hydraulic oil levels on the C6.4 ACERT before starting (every 10 hours/daily).
  • Drain water and sediment from the fuel system water separator (every 10 hours/daily).
  • Inspect undercarriage, track tension, rollers, and idlers for wear on the grease-lubricated track (every 10 hours/daily).
  • Test the travel alarm, seat belt, and instrument cluster (every 10 hours/daily).
  • Lubricate boom and stick linkage pins and bucket linkage (every 50 hours/weekly).
  • Inspect bucket cutting edge, teeth, and linkage for wear or looseness (every 50 hours/weekly).
Every 250 h
  • Check engine valve lash (initial 250-hour service).
  • Change final drive oil and swing drive oil (initial 250-hour service).
  • Replace hydraulic case drain, pilot, and return filters.
  • Pull an engine oil sample for analysis.
  • Inspect and adjust drive belt tension.
  • Lubricate the swing bearing and check final drive and swing drive oil levels.
Every 500 h
  • Change engine oil and filter on the C6.4 ACERT.
  • Replace primary and secondary fuel filter elements.
  • Clean the engine crankcase breather.
  • Lubricate boom and stick linkage.
  • Clean the fuel tank cap and strainer.
  • Pull swing system oil and coolant samples for analysis.
Every 1,000 h
  • Recheck engine valve lash.
  • Replace hydraulic system filters and check final drive oil level.
  • Change swing drive oil.
  • Clean battery terminals and tighten hold-downs.
  • Inspect the ROPS cab structure for damage or corrosion.
Every 2,000 h
  • Change final drive oil and hydraulic system oil.
  • Clean the hydraulic tank strainer screen.
  • Replace the cab air conditioning receiver-dryer.
  • Lubricate swing gear teeth.
  • Review injector leakoff and rail pressure trends against accumulated oil-sample history.
Every 3,000 h
  • Change hydraulic system oil where extended-life hydraulic fluid is specified (18-month milestone).
  • Inspect hydraulic pump and motor case drain flow against oil-sample trend data.
  • Inspect hydraulic hoses and fittings for wear, chafing, and leaks.
Every 6,000 h
  • Add coolant extender to maintain corrosion inhibitor levels (3-year milestone).
  • Pressure-test the cooling system and radiator cap.
  • Inspect the water pump, hoses, and thermostat for wear.
Every 12,000 h
  • Drain and flush the cooling system completely (6-year milestone).
  • Refill with extended-life coolant to full specification.
  • Inspect and replace worn coolant hoses and clamps.

Servicing the 323D SA beyond the schedule

Predictive Maintenance & Fluid Analysis

Pull oil samples from the C6.4 ACERT engine, swing drive, and final drives at every scheduled interval and track trends, not single results. Watch fuel dilution and soot loading as early signs of injector or leakoff-valve drift on the common-rail fuel system. Sample hydraulic oil at case drain filter changes to catch pump or motor wear before implement response degrades. Log coolant samples alongside engine oil to flag corrosion inhibitor depletion ahead of the long-interval coolant service points.

Corrective & Common Repairs

Sluggish or erratic boom, stick, and bucket response on the 323D SA often traces to the hydraulic pressure-reducing valve solenoid interacting with the engine speed sensor, not the pump. Check both before condemning a cylinder or valve section. Swing gearbox and final drive seals weep with age; reseal early to keep gear oil clean. Chassis harness connectors corrode at ground junctions and throw intermittent fault codes that clear on their own. Clean and dielectric-grease every connection during electrical troubleshooting.

Overhaul & Rebuild Points

Grease-lubricated track chain, rollers, and idlers on the 323D SA typically reach end of service life between 1,200 and 2,500 hours depending on ground conditions, driving full undercarriage rebuild decisions. Swing drive and final drive gear sets warrant teardown once oil samples show metal trending past normal wear rather than waiting for audible failure. On the C6.4 ACERT, plan injector and high-pressure fuel pump overhaul around major hour milestones tied to rail pressure and leakoff data. Reseal hydraulic pumps and motors at cylinder rebuild time to control cross-contamination.

Seasonal & Environment Servicing

Cold climates demand battery and starting-aid checks on the 323D SA before winter, plus coolant freeze-point verification, since the C6.4 ACERT is sensitive to coolant chemistry through the extended coolant-extender and full-change milestones. Hot, dusty sites accelerate radiator and hydraulic oil cooler core fouling and shorten air filter life, so shorten inspection cycles rather than waiting for the standard interval. Abrasive or wet ground speeds grease-lubricated undercarriage wear, so tighten track adjustment checks and re-lubricate boom and stick linkage more often in those conditions.

323D SA common service parts

Part numberPart
1R-0751Filter-FuelCheck fitment →
220-8678Seal-RingCheck fitment →
326-1644Filter As-Water Sep & FuelCheck fitment →
128-2686Filter Element As-AirCheck fitment →
131-8821Filter Element As-AirCheck fitment →

Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.

323D SA fault codes & troubleshooting

CodeMeaningLikely causeWhat to do
0100-04 (CID 100, FMI 4)Engine ECM reports the engine oil pressure sensor circuit reading below the normal voltage range.Shorted or grounded sensor wiring, a failed sensor, or a corroded/loose connector; less commonly an actual low oil pressure condition.Check engine oil level first, then inspect the sensor connector and wiring for a short to ground before replacing the sensor.
0110-03 (CID 110, FMI 3)Engine ECM reports the coolant temperature sensor circuit reading above the normal voltage range, an open-circuit type signal.Disconnected or corroded sensor connector, or damaged harness between the sensor and the ECM.Inspect the connector pins and harness routing near the sensor, check sensor resistance against spec, repair or replace as needed.
0168-04 (CID 168, FMI 4)Electrical system voltage at the ECM reads below normal.Weak or undercharged battery, loose or corroded battery terminal or ground strap, or a failing alternator.Load-test the batteries, clean and torque terminals and ground straps, then check charging system output.
0190-00 (CID 190, FMI 0)Engine speed sensor circuit reports an overspeed condition in the most severe data range.A real rpm spike from sudden load release, or a faulty speed/timing sensor signal mimicking overspeed.Review logged engine speed data with the service tool to confirm a real event versus a sensor glitch; check the speed sensor air gap and wiring if the fault repeats with no operator overspeed event.
0174-04 (CID 174, FMI 4)Fuel temperature sensor circuit voltage reads below normal.Shorted sensor circuit or a failed sensor, often from moisture intrusion at the connector.Dry and inspect the connector, check the circuit for a short to ground, replace the sensor if it fails the resistance check.
0262-04 (CID 262, FMI 4)The shared 5-volt reference supply feeding several engine sensors reads below normal; can trigger more than one sensor code at once.One shorted sensor or connector on the shared 5V circuit pulling the rail down, or corrosion at a connector on that circuit.Disconnect sensors on the affected 5V circuit one at a time while checking supply voltage to isolate the shorted branch before replacing any sensor.
1469-09 (CID 1469, FMI 9); also seen as 5856-09 for a secondary data link segmentAbnormal update rate on the machine's CAN data link between the engine and machine ECMs.Intermittent connector or wiring fault on the data link backbone, a loose module connector, or a module dropping off the network.Check data link connector pins and wiring for corrosion or damage, confirm all modules power up and communicate, then clear and recheck the code after repair.

Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.

323D SA attachments & work tools

Buckets

Pin-on GD (general duty), HD (heavy duty), and severe-duty buckets are offered for the 320-323 size class this machine belongs to. Heaped capacity spans roughly 0.4-1.7 m³ (0.5-2.2 yd³) depending on width and duty grade, with GD widths commonly from about 750 mm up to 1350 mm (30-54 in) for dirt, loam, and mixed dirt/gravel. HD and severe-duty buckets run narrower for clay, mixed rock, and abrasive digging. Buckets mount pin-on as standard, or via a pin-grabber quick coupler; exact capacity and width depend on the boom/stick combination fitted, so verify against the actual arrangement.

Hydraulic hammers

This machine's roughly 24.5 t (54,000 lb) operating weight puts it in the Cat H130 breaker class, which is matched to carriers from about 19,000-32,000 kg (42,000-70,000 lb). The H130 runs on 120-220 L/min (32-58 gpm) oil flow at roughly 14,000 kPa (2,030 psi) working pressure, with a breaker service weight around 1,700 kg (3,740 lb). Confirm hammer selection against the machine's actual auxiliary flow and pressure setup, since aux circuit ratings vary by configuration.

Quick couplers

Standard coupling for this size class is a pin-grabber quick coupler in the B-Linkage family, using 80 mm pins shared across the 318-323 machines. This lets the excavator swap buckets and other pin-on tools with same-class machines without a pin change. Hydraulic, in-cab-actuated couplers are the common setup for this class; mechanical pin-grabber versions also exist for the same linkage.

Thumbs/grapples

Hydraulic pin-on thumbs sized for the 80 mm bucket pin are available for this class, mounted alongside the standard bucket linkage for material sorting, loading, and pipe-handling control. Demolition and sorting grapples, plus multi-processor jaw sets (shear and pulverizer jaws), run through the machine's work-tool control circuit rather than a single base auxiliary line.

Rippers

A single-shank pin-on ripper, mounted on the stick in place of the bucket, is offered for this excavator weight class for breaking hard ground, frozen material, or light rock where a dozer-style ripper isn't practical. Availability and shank rating vary by attachment supplier for the 24-25 t class; no factory-integrated ripper is documented for this model.

Hydraulic-kit notes

Control circuits for high- and medium-pressure work tools (shears, grapples, hammers, pulverizers) are factory-optional on this machine, not standard equipment. Main hydraulic system relief runs around 35,000 kPa (5,000 psi). Match the work-tool circuit's flow and pressure setting to the specific tool's requirement; an undersized medium-pressure circuit under a hammer or thumb sized for high-flow will run sluggish.

Model catalog

Part Book

Browse by group, subgroup and unit. Part numbers are masked and diagram thumbnails are locked.

Selected unit

109-9313 Air Cleaner & Mounting Group s/n nes1-up Part of 324-4208 Installation ar-engine

109-9313 Air Cleaner & Mounting Group s/n nes1-up Part of 324-4208 Installation ar-engine is listed in the Air inlet and exhaust system / air cleaner & mounting group catalog section.

Group
Air Inlet and Exhaust System
Subgroup
Air cleaner & mounting group
Unit
109-9313 Air Cleaner & Mounting Group s/n nes1-up Part of 324-4208 Installation ar-engine
Machine reference: Caterpillar 323D SA
Machine reference

No catalog diagram available for this unit

Parts in this unit

Catalog descriptions with masked part numbers.

Part numberDescription
10***13Air Cleaner & Mounting Group; Spare Part 10***13 Air Cleaner & Mounting Group (Caterpillar)
31***67Air Cleaner Group; Spare Part 31***67 Air Cleaner Group (Caterpillar)
8t***21Washer-Hard; (11x21x2.5-mm thk)(m10x1.50x30mm); Spare Part 8t***21 Washer-Hard (Caterpillar)
8t***37Bolt (m10x1.50x20mm); Spare Part 8t***37 Bolt (m10x1.50x20mm) (Caterpillar)

323D SA serial number reference

The PIN plate sits on the excavator main frame, usually on the right-hand side near the base of the cab or on the front frame rail below the swing bearing; a duplicate PIN is often stamped into the frame itself as a backup. Read the first three characters of the 17-character PIN as the machine prefix (e.g. NES), which identifies the model/build series, then the following digits as the sequence number for that build run - pair the prefix with a dealer or Cat SIS lookup to pin down an exact build year.

PrefixIdentifies
NES323D SA

Frequently asked questions

What engine does the Cat 323D SA use?

The Cat 323D SA runs the Cat C6.4 ACERT, a 6-cylinder, 6.4 L diesel producing 110 kW (150 hp) net flywheel power, with 102 mm x 130 mm bore and stroke. It meets Tier 3/Stage IIIA emissions through in-cylinder combustion control, without diesel exhaust fluid or a diesel particulate filter.

What is the operating weight of the Cat 323D SA?

Baseline operating weight is about 24,500 kg (54,013 lb). Actual weight varies with the boom, stick, counterweight, and undercarriage configuration selected, so treat this as a nominal figure rather than a fixed number for every unit.

What replaced the Cat 323D SA?

Caterpillar carried the 323 platform forward through the 323E and then 323F generations before a full next-generation redesign of the 323 line. There is no single named successor to the SA configuration itself. Cat continued offering 323D-family machines (323D, 323D L, 323D LN, 323D S, 323D SA) side by side until D-series production wound down in favor of 323E output, and later Cat 323-family excavators carried the model number forward with different engines and control systems.

What 323D SA owners discuss

What do owners and mechanics say about hydraulic power and flow behavior on the 323D SA?
Reported loss of power under load traces most often to two spots: contamination-driven internal leakage in the main control valve, and an erratic engine speed signal. If the ECM sees engine rpm bouncing (for example reading roughly 1000-1900 rpm when actual speed holds near 1980 rpm), the PRV solenoid cuts pump output to protect the engine, so power drops even though the pump itself is fine. Jerky cylinder movement, overheated hydraulic oil, or a pressure drop under load point to contamination or worn pump/valve components rather than one bad part. Techs check the engine speed sensor and PRV solenoid wiring (solenoid resistance typically in the low double digits of ohms) before condemning the pump. Have your dealer verify PRV solenoid resistance and pump calibration before replacing major hydraulic components.
What undercarriage and track wear pattern is typical for the 323D SA?
The 323D SA ships with grease-lubricated (GLT) track chain as standard. While the internal joint grease holds, bushing and pin wear stays low; once it depletes, internal wear accelerates. Typical lubricated life on this class of undercarriage runs roughly 1200 to 2500 hours before internal wear becomes noticeable, though dirt and rock content, ground speed, and turning habits swing that range significantly. Rollers, carrier rollers, and idlers are sealed and lubricated from the factory and generally outlast the chain if kept clean. Inspect sprocket and bushing wear alongside chain sag rather than chain sag alone, since GLT chain can look tight while the bushings underneath are already worn.
What issues come up with the swing gearbox and final drives on this machine?
A recurring complaint on this D-series platform is the swing gearbox swivel (rotary) seal. It does not harden and crack cleanly, it disintegrates into small pieces that migrate into the return filter, so a clogged return filter with no visible external leak is a common early symptom. Because the case drain line tees into the swing motor housing, a failing swivel seal pressurizes the case drain and can accelerate swing motor wear or produce swing drift. On final drives, gear wear debris settling on the lower shaft seal acts as an abrasive over time, so a slow final-drive oil weep is often the first sign rather than a sudden failure. Have your dealer verify case drain pressure and swing motor condition before assuming the hydraulic pump or motor has failed outright.
What engine quirks show up on the C6.4 ACERT fitted to the 323D SA?
The C6.4 ACERT runs a high-pressure common-rail fuel system, and rail pressure fluctuation is the most-discussed engine complaint: logged rail pressure has been seen swinging well away from the commanded value (for example bouncing between roughly 25 and 45 MPa against a 35 MPa target), showing up as hard starting, stalling seconds after a cold start, or a power derate. Reported root causes include a failing fuel pressure sensor on the rail, a weak transfer pump, or air in the fuel system rather than the injectors themselves. Injectors are checked by return-line leakoff rate; a leakoff above roughly 38 mL (1.3 oz) per 30 seconds of cranking at 150 rpm is treated as the threshold for replacement. After any injector replacement, each unit needs its trim code reprogrammed in the ECM, or expect a rough idle and poor fuel economy afterward.
What electrical and sensor problems come up most often?
Electrical gremlins on this generation trace mostly to connectors, not components. Moisture intrusion at harness connectors and stressed harness routing near the engine and pump compartment produce intermittent fault codes that come and go with vibration or wet weather. A voltage-above-normal or voltage-below-normal circuit code usually means a short to power, a short to ground, or an open signal wire in the harness rather than a dead sensor, so the sensor's 5V or 8V supply from the ECM and the connector pins get checked before parts get swapped. Corroded or loose harness pins are the most common root cause found after chasing an otherwise unexplained intermittent fault.
What should a buyer check before purchasing a used 323D SA?
Open the hydraulic pump compartment and check hoses, cylinders, and the slew ring for leaks; rotate the house a quarter turn to feel for play in the swing bearing, since a worn slew ring is one of the costliest repairs on this machine. Check boom, stick, and bucket pin/bushing play, and look along welds on the boom, stick, and frame for cracked paint or a rust bleed line that signals a crack underneath. On the C6.4, check exhaust smoke pattern, oil condition, and blow-by. Pull the hydraulic return filter and check its condition as an early tell for a failing swing swivel seal. On the undercarriage, judge GLT track wear by bushing and pin condition, not chain sag alone, and check roller/idler seals for weeps. Run every cab control, gauge, and safety switch for smooth, responsive operation, and ask for maintenance and fault-code history if it exists. Have your dealer verify slew ring play and structural weld condition before final purchase, since both are safety-critical and expensive to miss.
Beyond the known wear items, how do operators rate the 323D SA overall?
General sentiment on this class of mid-size Cat excavator is positive. Operators describe the cab as roomy and comfortable with good sightlines and easy switch access, hydraulics with plenty of power for the machine's size, and no complaints about swing or travel performance when maintenance stays current. Complaints cluster around the known engine and electrical items rather than structural or powertrain design flaws, and the machine is generally regarded as strong on bucket dig force and stability through heavy cycles, with its size and weight being the main drawback on tight job sites.

Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.

Need a specific 323D SA part?

Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.

Post a parts request and compare supplier quotes.