Caterpillarskid steer loadercompact track loader
Caterpillar 279C
Maintenance schedule, common problems & OEM parts breakdown
The Cat 279C is a compact track loader (Caterpillar's own line groups it under its multi terrain/skid steer loader family, though it runs on steel-embedded rubber tracks, not wheels). It uses a radial-lift boom on a fully suspended undercarriage with independent torsion axles, the first fully suspended undercarriage Caterpillar built for a compact track loader. The base 279C runs the Cat C3.4 DIT (3044C) four-cylinder turbo diesel at 84 hp gross / 82 hp net, Tier 3 / Stage IIIA. The later 279C Series 2 keeps the same engine block, retuned to 74 hp gross / 73 hp net for Tier 4 Interim / Stage IIIB. Operating weight runs 4,475 to 4,487 kg (9,866 to 9,892 lb) across both series, depending on configuration. The base 279C was built roughly from the mid-2000s into the early 2010s; the Series 2 update then carried the model through about 2015 before the 279D took over. Cat offered it open-ROPS or in an enclosed cab with heat or heat-and-air-conditioning, with standard-flow or high-flow XPS hydraulics, and a manual or hydraulic quick coupler for work tools.
The change between series is mostly an emissions step: Tier 3 to Tier 4 Interim dropped rated power on the same C3.4 DIT block, and a redesigned undercarriage shortened the track-to-ground contact length, shifting ground pressure and tipping load slightly between the two. Chassis, hydraulics, and drivetrain layout carry over closely enough that most wear parts and service work cross over between the 279C and the 279C2; that commonality stops at the 279D, which switched to a different, smaller-displacement Cat C3.3B DIT engine at Tier 4 Final. In the used and parts market today, both C-series generations are well past factory warranty and into independent-shop territory, with a sizable installed base driving steady demand for undercarriage, hydrostatic-drive, and fuel-system parts. Match the serial prefix to the series before ordering parts: the base 279C and the Series 2 update use different prefixes, and engine tuning plus some hydraulic components differ between them even though the chassis is shared.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 279C specifications
Engine
| Engine model | Cat C3.4 DIT — 4-cylinder, turbocharged, direct-injection diesel, liquid-cooled. Same base engine family carries over from the 279C to the 279C Series 2, retuned for the later emissions step. |
| Gross power | 279C: 84 hp (63 kW) @ 2500 rpm (SAE J1995). 279C Series 2: 74 hp (55 kW), same rating standard. |
| Net power | 279C: 82 hp (61 kW) (SAE J1349). 279C Series 2: 73 hp (54 kW) (SAE J1349). |
| Displacement | 3.3 L (201 cu in) |
| Bore x stroke | 94 mm x 120 mm (3.70 in x 4.72 in) |
| Aspiration / fuel system | Turbocharged, direct injection |
| Emissions tier | 279C (base series): Tier 3 / Stage IIIA. 279C Series 2: Tier 4 Interim / Stage IIIB — the lower power rating on Series 2 reflects this emissions step, not a different engine. |
Weights
| Operating weight | 279C: approx 9,890-9,892 lb (4,485-4,487 kg). 279C Series 2: approx 9,866 lb (4,475 kg). |
| Shipping weight | Not published as a separate figure for this class; operating weight is the weight Cat publishes for transport planning. |
| Ground pressure | 279C: 4.0 psi (0.28 bar). 279C Series 2: 4.3 psi (0.30 bar / 29.5 kPa) — Series 2 uses a redesigned, fully suspended undercarriage with a shorter ground-contact patch, which raises ground pressure slightly. |
| Tipping load | 279C: approx 6,480-6,483 lb (2,940 kg). 279C Series 2: 6,100 lb (2,767 kg). |
Dimensions
| Overall length, with bucket | 144.8 in (3.68 m), both series |
| Overall length, without bucket | 116.5 in (2.96 m), both series |
| Overall width, over tracks | 78 in (1.98 m), both series |
| Height to cab top | 83.3 in / 6.95 ft (2.12 m), both series |
| Max hinge-pin height, boom raised | 123.2 in (3.13 m); overall machine height with boom raised is approx 157.7 in (4.0 m) |
| Hinge-pin height, carry position | approx 7.7 in (195 mm) |
| Ground clearance | 9.1 in (231 mm), both series |
| Track length on ground | 279C: approx 69.6 in (1.77 m). 279C Series 2: 64 in (1.63 m) — shorter contact length from the Series 2 undercarriage redesign. |
| Turning radius | Over bucket corner: approx 91.1 in (2.31 m). To rear corner of machine: approx 64.6-69.4 in (1.64-1.76 m), varies by series/source. |
Performance
| Travel speed | 2-speed hydrostatic drive. Low range: 5.0-5.1 mph (8.1-8.2 km/h). High range: 8.5 mph (13.6-13.7 km/h). Same for both series. |
| Bucket breakout force | approx 7,308-7,310 lb (3,315 kg), both series |
| Rated operating capacity | 279C: 3,200 lb (1,451 kg) at 50% of tipping load. 279C Series 2: 3,049 lb (1,383 kg), ISO 14397 rating — figures are not directly comparable since they use different tipping-load fractions. |
| Maximum dump angle | 40 degrees, both series |
| Departure angle | approx 44 degrees |
| Dump height, fully raised | approx 95.6-96 in (2.42-2.44 m) |
| Dump reach, max height | approx 23.4-24 in (0.59-0.61 m) |
| Gradeability / drawbar pull | Not published by the factory for this loader class. |
Service capacities (summary)
| Fuel tank | 25.8-26.0 gal (98-98.4 L) |
| Hydraulic system, total | 15.0-15.1 gal (56.8-57.2 L); hydraulic tank alone approx 10.3-11 gal (39-42 L) |
| Engine oil (crankcase) | 2.6-2.7 gal (9.8-10.2 L) |
| Cooling system | 3.7 gal (14.0 L) |
| Hydraulic pump flow | Standard: approx 22 gpm (84 L/min) at 3,335 psi (230 bar). High-flow XPS option: approx 33 gpm (125 L/min) at 4,060 psi (280 bar). |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
279C fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 10.0 L (2.6 US gal) | Cat DEO-ULS (API CJ-4) SAE 10W-30 for -18C to 40C (0F to 104F), or SAE 15W-40 for -10C to 50C (14F to 122F). Cat DEO (API CI-4/CI-4 PLUS) is an accepted equivalent for this pre-Tier 4, non-aftertreatment engine. Cat DEO-ULS SYN SAE 5W-40 extends cold-start range to -30C (-22F); Cat DEO Cold Weather SAE 0W-40 covers down to -40C (-40F). |
| Cooling system | 14.0 L (3.7 US gal) | Cat ELC (Extended Life Coolant), premixed 50/50 with water, is preferred. Cat DEAC conventional antifreeze/coolant with Cat SCA maintained at 3-6% concentration is an acceptable alternative. Minimum 30% glycol by volume is required, 50% glycol is recommended for full freeze and boil protection. |
| Fuel tank | 98.0 L (25.8 US gal) | Ultra Low Sulfur Diesel (15 ppm sulfur max) or Low Sulfur Diesel meeting the Cat distillate diesel fuel specification. Biodiesel blends up to B20 are acceptable when the blend meets the applicable ASTM/Cat biodiesel quality requirements. |
| Hydraulic system (pump, lines, and tank combined) | 57.0 L (15.0 US gal) | Cat HYDO Advanced 10 (SAE 10W) is the typical factory-fill grade, rated -20C to 40C (-4F to 104F). Cat HYDO Advanced 20 (SAE 20W) suits -5C to 45C (23F to 113F); Cat HYDO Advanced 30 (SAE 30) suits warmer climates up to 50C (122F). Cat Bio HYDO Advanced is the option where a biodegradable fluid is required. Second-choice fluids include Cat TDTO-TMS, Cat MTO, Cat DEO-ULS, or Cat DEO in the equivalent viscosity grade. |
| Hydraulic tank (reservoir) | approximately 39-42 L (10.3-11.1 US gal) - varies by source/configuration | Same fluid as the hydraulic system above (Cat HYDO Advanced by climate grade, or Cat Bio HYDO Advanced for biodegradable service). |
| Final drive (each, two total) | approximately 1.0 L (1.1 US qt) per side - single-source figure, verify with dealer | Cat Synthetic GO SAE 75W-140, rated -30C to 45C (-22F to 113F), is the specified final-drive oil for this compact track loader family. |
| Track idlers and rollers (sealed oil-filled bogies) | not separately published; sealed units serviced by oil-level check rather than routine drain | Cat DEO-ULS or Cat DEO SAE 15W-40 is factory fill, rated -10C to 50C (14F to 122F). Cat DEO Cold Weather SAE 0W-40 covers down to -40C (-40F); Cat DEO-ULS SYN SAE 5W-40 or Cat FDAO SYN extend the range for cold or continuous-duty service. |
| Grease (all grease fittings) | N/A - grease specification only, no fill capacity | Cat Prime Application Grease (NLGI 2, lithium-complex base with 3% moly) covers pin joints and general moderate-to-high-severity service typical of skid steer and compact track loaders. Cat Extreme Application Grease (NLGI 1 or 2, calcium-sulfonate complex, 5% moly) is specified for severe or high-impact duty. Cat Utility Grease (NLGI 2) is acceptable for low-severity, light-duty points. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 279C maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 6,000 h |
|
Servicing the 279C beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S·O·S oil sampling on the C3.4 DIT at every engine oil change and pull hydraulic and coolant samples every 500 hours. Rising iron or copper in the engine sample flags injector or injection pump wear before a hot-restart no-start becomes a tow-in. Hydraulic sample trends catch contamination migrating toward the drive motors and pump before a hydrostatic coupling failure takes out drive, lift, and cooling fan together. Track sag checks double as a predictive read on undercarriage bushing wear.
Corrective & Common Repairs
Hot engines that crank but won't restart usually trace to a heat-soaked fuel shutoff solenoid or vapor-locked injection components, not the battery or starter; check solenoid wiring and fuel filter condition first. A rough-running engine under load gets blamed on the turbo more often than the actual cause: worn injectors, incorrect valve lash, or a suction-side air leak. Dead joystick functions usually mean a starved fusebox circuit or a tripped door/seat interlock, not a failed Hall-effect joystick sensor.
Overhaul & Rebuild Points
Simultaneous weakness in drive, hydraulics, and cooling fan speed points to a slipped or failed coupling between the engine and hydrostatic pump, a major driveline overhaul rather than a sensor fault. Injection pumps on the C3.4 DIT have needed replacement more than once on some units by mid-life; budget for it in a rebuild. Final drives are simple planetary reductions at each sprocket; rebuild when oil samples or sprocket-tooth wear show ratcheting damage from a chronically loose track.
Seasonal & Environment Servicing
Match engine oil and coolant grade to season: Cat DEO-ULS 15W-40 or synthetic 5W-40 for cold starts, DEO Cold Weather 0W-40 below -30C (-22F), and extended life coolant held near 50% glycol for hard freeze protection. Check track tension more often through temperature swings since sag changes with rubber temperature. Clean radiator and aftercooler cores frequently in dusty or brush environments, and fit the forestry guarding package before mulching or land-clearing work to protect the cab and undercarriage.
279C common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 233-9856 | Filter As-Water Sep & Fuel | Fuel system service | Check fitment → |
| 110-6326 | Filter Element As-Air | Air intake service | Check fitment → |
| 110-6331 | Filter Element As-Air | Air intake service | Check fitment → |
| 265-6618 | Filter Element-Cab Air | Air intake service | Check fitment → |
| 265-6619 | Filter Element-Cab Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
279C fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| 41-04 | Machine ECM 8V sensor reference supply reading below normal. | Short to ground on one sensor signal wire loading down the shared 8V circuit (this supply feeds the throttle position sensor and the left/right drive motor speed sensors), or a chafed harness section. | Disconnect sensors on the 8V circuit one at a time to isolate the short before replacing any single sensor; this code often triggers several other sensor codes at once, so clear it first. |
| 875-02 | System/battery voltage measured below about 12.0V for more than 30 seconds. | Weak or undercharged battery, corroded battery terminals/ground strap, or a charging system fault. | Load-test the battery and check alternator output and ground connections before replacing components. |
| 190-08 | Engine speed/timing signal is an abnormal frequency, pulse width, or period (intermittent or lost signal from the primary engine speed sensor). | Incorrect sensor-to-tone-wheel air gap, a damaged tone ring tooth, or a corroded sensor connector. | Check the sensor air gap with a feeler gauge and inspect the connector for corrosion before replacing the sensor. |
| 2685-08 / 2686-08 | Left drive motor speed sensor #1/#2 signal is erratic or an abnormal frequency; on machines with the digital display this shows as an unexpected forward/reverse speed event on the left side. | Damaged or pinched harness wiring near the left drive motor, sensor air gap out of spec, or debris on the sensor tone wheel. | Inspect the harness routing to the left drive motor for chafing or loose connectors and check sensor gap before replacing the sensor. |
| 2687 / 2688 | Right drive motor speed sensor #1/#2 circuit fault (open circuit or erratic signal); mirrors the left-side 2685/2686 pair on the opposite drive motor. | Damaged wiring between the right drive motor and the main harness, a loose connector, or a failed sensor. | Check harness continuity from the right motor connector back to the machine ECM before replacing the sensor. |
| 2471-03 | Cab door switch circuit voltage reading above normal. | Open circuit in the door switch wiring, or a switch that never closes to ground when the door shuts. | Check the door switch and its connector for corrosion or an open wire before replacing the switch. |
| 91-08 | Throttle position sensor signal is an abnormal frequency, pulse width, or period. | Worn or misadjusted throttle position sensor, or a damaged connector on the shared sensor supply circuit. | Check sensor connector condition and confirm supply voltage at the sensor before replacing it. |
| High Hydraulic Oil Temperature warning | Hydraulic oil temperature has climbed into the warning range (roughly 93 C / 199 F); the operator display/warning icon prompts reduced operation to let it cool rather than an immediate shutdown. | Low hydraulic fluid level, a clogged or debris-packed oil cooler, or a weak/failing cooling fan. | Check fluid level and clean debris from the cooler core, then confirm the cooling fan runs and airflow across the cooler drops the temperature before returning to full duty. |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
279C attachments & work tools
Buckets
General purpose, high-capacity, dirt/utility, light-material, and multi-purpose (4-in-1) buckets are offered for this machine class. A typical general-purpose bucket runs about 1.98 m (78 in) wide with a heaped capacity near 0.48 m³ (0.63 yd³); width and capacity vary with the bucket style ordered.
Grapple buckets
Industrial grapple and utility grapple bucket variants add a hydraulically clamped top grapple to a standard bucket shell for handling brush, debris, and loose material. These run off the machine's standard auxiliary hydraulic circuit.
Forks
Pallet forks for palletized loads and utility forks for pierceable debris and waste are offered for this size class. Carrying capacity is limited by the machine's rated operating capacity, so load charts should be checked against attachment weight and load center.
Root/brush grapples and rakes
Root rake grapples and grapple rakes are offered for land-clearing and brush handling, running on the standard auxiliary circuit. Heavier land-management work with these tools is usually paired with the forestry guarding package.
Augers
Auger drives with interchangeable bits are offered for post holes, footings, fence posts, and tree planting. Smaller-diameter bits run on the standard-flow circuit; larger-diameter bits need the high-flow option for adequate torque and cycle time.
Cold planers
Compact cold planer attachments in the smaller cutting-width class are compatible with this machine but require the high-flow or high-flow XPS hydraulic circuit to drive the cutting drum; a standard-flow machine cannot run this class of tool.
Mulching heads and brush cutters
Forestry mulching heads and rotary brush cutters are used on this machine in high-flow configuration; the auxiliary circuit is switched into high-flow mode to supply the mulcher's hydraulic motor. Forestry cab guarding is recommended alongside this work tool.
Snow attachments
Snow blowers (hydraulically driven auger and impeller, with chute and deflector run from the cab) and snow blades/pushers are offered for this size class. Blower and chute functions are operated through the machine's dual joystick controls.
Brooms
Angle broom / pickup-sweeper attachments are offered, using a windrowing action to push loose debris ahead of and to the side of the machine. These typically run on the standard-flow auxiliary circuit.
Site-prep tools: blades, trenchers, backhoe
Grader/dozer blades, trenchers, and backhoe-style digging attachments are offered in this size class for site preparation and utility work, all driven from the auxiliary hydraulic circuit. Backhoe-style units generally need the high-flow circuit for best cycle times.
Quick coupler / mounting system
Work tools attach via Caterpillar's own bar-and-pin quick coupler, built to the industry-standard universal skid-steer attachment pattern. Standard engagement is manual with two high-leverage handles; a factory or dealer-installed hydraulic quick coupler option lets the operator engage and release tools from the cab. This coupler and hydraulic interface carries forward into the later running update of this model.
Auxiliary hydraulic circuit
Standard auxiliary flow is about 22 gpm (84 L/min) at roughly 3335 psi (230 bar). An optional high-flow (XPS) circuit raises flow to about 33 gpm (125 L/min) at up to roughly 4060 psi (280 bar), load-sensing and pressure-compensated, and is needed for higher-demand work tools such as cold planers and mulching heads.
Work-tool electrical connector
A multi-pin electrical connector at the front of the machine supplies power and signal to electro-hydraulic work tools, such as angle-adjustable blades or proportional-control grapples, operated from the cab joystick without separate wiring runs.
Guarding options
A forestry guard package, with mesh/screen cab and window guards plus belly/undercarriage guarding, is offered as a factory or dealer-installed option for brush, mulching, and land-clearing work. Standard machines ship with basic lift-arm and rear guarding only.
All 279C assemblies by section
Every catalogued assembly group for the Caterpillar 279C. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
258-3320 Air Cleaner Gp
| 15***98 | Band-Mounting | 1 |
| 23***25 | Indicator | 1 |
| 25***20 | Air Cleaner Group | 2 |
258-3453 Air Cleaner Gp
| 12***70 | Capscrew; (Button Hd) (M8x1.25x20) (G10.9) | 2 |
| 13***43 | Clamp-Hose | 1 |
| 25***11 | Plate | 1 |
280-8294 Air Cleaner Gp
| 28***94 | Air Cleaner Group | 1 |
| 28***55 | Guard As-Exhaust; (Turbocharger) | 1 |
| 28***91 | Flange, Guard-Exhaust; (Manifold) | 1 |
280-8393 Guard Gp-Debris -Turbocharger, Exhaust Manifold
| 27***52 | Guard-Exhaust; (Manifold) | 1 |
| 28***55 | Guard As-Exhaust; (Turbocharger) | 1 |
| 28***93 | Guard Group-Debris; -Turbocharger, Exhaust Manifold | 1 |
272-3062 Kit-Debris Guard -Turbocharger, Exhaust Manifold
| 27***62 | Kit-Debris Guard; -Turbocharger, Exhaust Manifold | 1 |
| 5I***78 | Gasket | 1 |
| 5I***21 | Elbow Assem. | 1 |
247-6317 Lines Gp-Air
| 24***17 | Lines Group-Air | 1 |
| 25***64 | Hose As | 1 |
| 5P***68 | Clamp-Hose; (Us Sourced) | 1 |
316-0471 Lines Gp-Air
| 19***60 | Nut; (M8x1.25-Thd) | 8 |
| 23***60 | Bolt | 8 |
| 23***24 | Gasket-Manifold | 1 |
315-7769 Lines Gp-Air
| 19***22 | Bolt As; (M8x1.25x22-mm) | 4 |
| 27***82 | Clip | 2 |
| 31***40 | Elbow | 1 |
258-2465 Lines Gp-Air
| 09***00 | Washer; (1.5mm Thk) | 2 |
| 25***12 | Clip | 1 |
| 25***65 | Lines Group-Air | 1 |
287-5323 Manifold Gp-Exhaust
| 09***49 | Bolt; (M8x1.25x40-mm) | 12 |
| 23***05 | Manifold-Inlet | 1 |
| 23***06 | Gasket; (Inlet Manifold) | 1 |
335-5750 Manifold Gp-Inlet
| 19***76 | Washer-Hard; (8.8x20x8-mm Thk) | 3 |
| 23***21 | Nut; (M10x1.25-Thd) | 1 |
| 25***19 | Muffler As | 1 |
287-4832 Manifold Gp-Inlet
| 09***49 | Bolt; (M8x1.25x40-mm) | 11 |
| 23***05 | Manifold-Inlet | 1 |
| 23***06 | Gasket; (Inlet Manifold) | 1 |
280-8347 Muffler & Mounting Gp
| 09***00 | Washer; (1.5mm Thk) | 3 |
| 19***06 | Gasket | 4 |
| 23***18 | Gasket | 1 |
258-2462 Muffler & Mounting Gp
| 19***76 | Washer-Hard; (8.8x20x8-mm Thk) | 3 |
| 23***21 | Nut; (M10x1.25-Thd) | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
315-7768 Turbocharger Gp
| 13***87 | Clip | 1 |
| 19***36 | Insert-Threaded; (M6x1-Thd) | 3 |
| 23***96 | Screw-Flat Head; (M6x1x35-mm) | 4 |
Basic Engine
323-2009 Accessory Gp-Engine
| 32***09 | Accessory Group-Engine | 1 |
| 34***61 | Kit-Gasket | 1 |
292-4041 Bearing Gp-Main
| 10***88 | Plate-Thrust; (Standard) | 3 |
| 10***89 | Plate-Thrust; (0.15-mm Os) | 0 |
| 10***90 | Plate-Thrust; (0.35-mm Os) | 0 |
314-9835 Camshaft Gp
| 09***28 | Key | 1 |
| 10***72 | Tappet | 8 |
| 10***73 | Rod-Push | 8 |
287-4033 Connecting Rod Gp
| 10***80 | Rod As-Connecting | 4 |
| 12***55 | Bolt-Connecting Rod | 2 |
| 12***56 | Nut | 2 |
315-7762 Cover Gp-Valve Mechanism
| 09***49 | Bolt; (M8x1.25x40-mm) | 5 |
| 23***83 | Gasket; (Valve Cover) | 1 |
| 31***98 | Cap-Oil Filler; (Engine) | 1 |
314-9860 Crankshaft Gp
| 08***13 | Pin | 2 |
| 09***28 | Key | 2 |
| 13***96 | Nut | 1 |
315-8330 Cylinder Block Gp
| 09***41 | Cap | 10 |
| 09***20 | Pin | 2 |
| 10***76 | Bolt-Bearing Cap | 10 |
315-7760 Cylinder Head Gp
| 10***46 | Bolt-Cylinder Head | 17 |
| 29***45 | Gasket-Head | 1 |
| 31***60 | Cylinder Head Group | 1 |
258-2452 Drain Gp-Engine Oil
| 11***70 | Cap | 1 |
| 1P***78 | Clamp; (Hose) | 1 |
| 21***19 | Adapter | 1 |
314-9861 Flywheel Gp
| 03***39 | Gear-Starter; (112-Teeth) | 1 |
| 22***93 | Bolt; (M12x1.25x30-mm) | 6 |
| 23***91 | Flywheel As | 1 |
315-7766 Gear Gp-Front
| 11***27 | Gear; (46-Teeth) | 1 |
| 11***29 | Gear; (23-Teeth) | 1 |
| 11***85 | Gear-Pump; (Oil, 31-Teeth) | 1 |
280-8407 Guard Gp-Belt
| 10***80 | Gasket-Rear | 1 |
| 11***15 | Seal As-Oil | 1 |
| 14***17 | Bolt; (M10x1.25x25-mm) | 10 |
258-2469 Guard Gp-Belt
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 4 |
| 13***22 | Bolt-Locking; (M8x1.25x16-mm) | 2 |
| 25***43 | Guard-Belt | 1 |
315-7764 Housing Gp-Flywheel
| 09***00 | Washer; (1.5mm Thk) | 2 |
| 09***29 | Seal-O-Ring (Id=139.5mm); (Id=139.50mm) | 1 |
| 19***12 | Bolt; (M6x1x18-mm) | 4 |
315-8336 Housing Gp-Front
| 23***66 | Eye | 1 |
| 23***68 | Gasket; (Rear Head) | 1 |
| 31***04 | Cover | 1 |
315-7761 Lifting Gp-Engine
| 11***90 | Mount As | 2 |
| 12***80 | Locknut; (M12x1.75-Thd) | 1 |
| 14***88 | Mount-Engine | 2 |
258-2447 Mounting Gp-Engine
| 09***82 | Gasket, Oil Drain | 1 |
| 13***32 | Plug; (Drain, Engine Oil) | 1 |
| 16***01 | Sealant-Silicone | 1 |
335-5772 Pan Gp-Oil
| 23***15 | Pin-Piston | 4 |
| 25***38 | Ring-Snap | 8 |
| 31***52 | Piston; (0.25-mm Os) | 0 |
315-7765 Pan Gp-Oil
| 09***82 | Gasket, Oil Drain | 1 |
| 13***32 | Plug; (Drain, Engine Oil) | 1 |
| 16***01 | Sealant-Silicone | 1 |
314-9855 Piston Gp
| 31***55 | Piston Group | 1 |
| 5I***05 | Plug | 6 |
287-2922 Plug Gp-Engine
| 19***11 | Plug | 1 |
| 28***22 | Plug Group-Engine; -Cylinder Block, Lh | 1 |
287-2983 Plug Gp-Engine
| 28***83 | Plug Group-Engine; -Cylinder Block, Rh | 1 |
| 30***97 | Pulley-Crankshaft; (2-Groove) | 1 |
301-3396 Pulley Gp-Crankshaft
| 23***07 | Pulley | 1 |
| 30***96 | Pulley Group-Crankshaft | 1 |
| 8T***42 | Bolt; (M8x1.25x14-mm) | 4 |
287-6114 Pulley Gp-Water Pump
| 28***14 | Pulley Group-Water Pump | 1 |
| 35***69 | V-Belt; (Water Pump) | 1 |
287-6138 V-Belt Gp
| 09***05 | Cap | 1 |
| 19***24 | Ring-Snap | 2 |
| 22***45 | Rocker As | 8 |
235-5880 Valve Mechanism Gp
| 09***37 | Seal-O-Ring | 1 |
| 09***71 | Seal-O-Ring (Id=94.40mm) | 1 |
| 1R***34 | Filter-Engine Oil | 1 |
Cooling System
314-9900 Cooler Gp-Engine Oil
| 09***13 | Seal-O-Ring | 4 |
| 09***21 | Plug | 2 |
| 23***98 | Stud | 1 |
315-7763 Drain Gp-Coolant
| 09***75 | Bolt; (25-mm Long) | 2 |
| 23***09 | Washer-Special | 1 |
| 23***31 | Cover | 1 |
315-8355 Housing & Regulator Gp
| 16***15 | Cap-Vented; (Coolant Recovery Tank) | 1 |
| 1P***78 | Clamp; (Hose) | 2 |
| 22***78 | Clamp-Tbolt; (M5x0.8) | 4 |
258-3552 Lines Gp-Water -Radiator
| 14***32 | Pin As | 1 |
| 17***55 | Pin | 2 |
| 20***76 | Stud-Ball | 4 |
258-3542 Mounting Gp-Rad & Oil Cooler
| 25***42 | Mounting Group-Rad & Oil Cooler | 1 |
| 28***66 | Bolt; (M8x1.25x65-mm) | 1 |
| 31***89 | Adapter | 1 |
335-9117 Pump Gp-Water
| 03***65 | Cap As-Radiator; (Sea Water Heat Exchanger) | 1 |
| 06***80 | Fitting | 1 |
| 12***52 | Spacer; (10.5x20x28-mm Thk) | 1 |
315-7770 Pump Gp-Water
| 10***47 | Cover-Pump | 1 |
| 19***60 | Plug | 1 |
| 31***70 | Pump Group-Water | 1 |
258-3459 Radiator & Hyd Oil Cooler Gp
| 11***26 | Filter Element As-Air; (Primary) | 1 |
| 11***31 | Filter Element As-Air; (Secondary) | 1 |
| 11***17 | Valve-Dust; (Air Cleaner) | 1 |
Electrical And Starting System
105-2814 Alternator Gp-Charging
| 03***05 | Terminal-Cable; (00-Ga, 5/16-In Screw) | 1 |
| 10***14 | Alternator Group-Charging | 1 |
| 11***16 | Block | 1 |
315-8353 Alternator Gp-Charging
| 31***72 | Module Group-Interface; (Key) | 1 |
| 31***53 | Alternator Group-Charging | 1 |
| 6V***15 | Screw-Pan Head; (4-20x0.25-In) | 1 |
258-4121 Battery & Wiring Gp
| 11***71 | Puller-Minifuse | 1 |
| 25***27 | Screw-Truss Head; (No 12x17.46-mm) | 2 |
| 25***21 | Battery & Wiring Group | 1 |
310-5289 Control Gp-Machine
| 10***59 | Glow Plug | 4 |
| 25***90 | Plate-Connection | 1 |
| 31***89 | Control Group-Machine | 1 |
258-4144 Cover Gp-Fuse Panel
| 22***41 | Element As-Jacket Water Heater; (120-Volt, 530-Watt) | 1 |
| 22***42 | Heater Group-Jacket Water | 1 |
| 23***03 | Gasket | 1 |
258-4103 Electronics Gp-Machine
| 13***17 | Cap As-Dust | 1 |
| 21***12 | Cord As | 1 |
| 22***35 | Element As-Jacket Water Heater; (240-Volt, 530-Watt) | 1 |
347-4186 Electronics Gp-Monitor -Monitor
| 15***28 | Spacer; (7x16x20-mm Thk) | 4 |
| 25***27 | Screw-Truss Head; (No 12x17.46-mm) | 9 |
| 25***48 | Plate As | 1 |
347-4187 Electronics Gp-Monitor
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***17 | Tape; (5.5m) | 0 |
235-5904 Glow Plug Gp
| 15***71 | Kit-Connecting Plug; (4-Pin) | 0 |
| 18***40 | Socket-Connector; (14-Ga To 18-Ga)(14-Ga To 18-Ga) | 2 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
218-0942 Heater Gp-Jacket Water
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***39 | Relay As | 3 |
218-0943 Heater Gp-Jacket Water
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 21***43 | Heater Group-Jacket Water | 1 |
258-4145 Kit-Control Mounting -Product Link
| 10***53 | Case, Spacer; (Spherical) | 1 |
| 10***54 | Spacer; (Spherical) | 1 |
| 10***55 | Washer; (Spherical) | 1 |
258-4185 Kit-Security
| 10***53 | Case, Spacer; (Spherical) | 1 |
| 10***54 | Spacer; (Spherical) | 1 |
| 10***55 | Washer; (Spherical) | 1 |
328-2366 Kit-Wiring Harness -Accugrade
| 32***66 | Kit-Wiring Harness; -Accugrade | 1 |
| 9R***42 | Plug As | 1 |
| 9R***58 | Cord As | 1 |
258-4127 Kit-Work Tool Wiring
| 25***27 | Kit-Work Tool Wiring | 1 |
| 27***00 | Lens; (Amber)(Warning Beacon) | 1 |
| 9R***42 | Plug As | 1 |
234-4328 Lamp Gp-Flood
| 23***28 | Lamp Group-Flood; -Front, Rear, Wide Range | 3 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 4 |
195-0190 Lamp Gp-Head & Signal -Lh
| 08***48 | Lamp; (12-Volt, 5-Watt) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
195-0189 Lamp Gp-Head & Signal -Rh
| 08***48 | Lamp; (12-Volt, 5-Watt) | 1 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
309-1325 Lamp Gp-Warning Beacon -Amber
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 26***23 | Switch As-Rocker; (Warning Beacon) | 1 |
128-6985 Lamp Gp-Warning Beacon -Amber, Magnetic Mount, Rotating
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 16***95 | Lens | 1 |
258-4164 Lighting Gp-Flood -Work Lights, Front
| 24***97 | Cable-Coiled; (Sensor) | 1 |
| 25***29 | Receiver Group-Laser; (Lr410) | 1 |
| 25***29 | Case-Carrying | 1 |
258-4130 Lighting Gp-Roading -Head, Signal, Stop, Tail
| 1H***44 | Lockwasher (Bracket To Cab) | 2 |
| 25***30 | Lighting Group-Roading; -Head, Signal, Stop, Tail | 1 |
| 26***80 | Fuse; (20-Ampere)(Main) | 1 |
333-4957 Lighting Gp-Roading -Rear
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 3 |
| 33***57 | Lighting Group-Roading; -Rear | 1 |
258-4169 Lighting Gp-Stop & Tail
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 17***49 | Strap; (Marker) | 1 |
| 25***69 | Lighting Group-Stop & Tail | 1 |
258-4184 Lighting Gp-Warning Beacon -Amber, Magnetic Mount, Rotating
| 25***84 | Lighting Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 30***87 | Control Group-Unprogrammed; (Transmission) | 1 |
| 35***39 | Software Group-Machine | 1 |
292-1271 Mast Gp -Accugrade Laser
| 29***71 | Mast Group; -Accugrade Laser | 1 |
| 34***36 | Control Group-Unprgmed Monitor; (Machine) | 1 |
| 35***58 | Software Group-Monitor | 1 |
258-4135 Relay Gp -Main Power
| 10***85 | Cap-Starting Motor | 1 |
| 10***12 | Kit-Contact; (Starting Motor) | 1 |
| 10***13 | Switch As; (Starting Motor)(12-Volt) | 1 |
266-1467 Sensor Gp-Position -Rotary
| 14***39 | Starting Motor Group-Electric; -12-Volt | 1 |
| 26***67 | Sensor Group-Position; -Brake Pedal | 1 |
191-8303 Sensor Gp-Speed
| 19***03 | Sensor Group-Speed | 1 |
| 32***52 | Switch-Oil Press; (Engine) | 1 |
262-3764 Sensor Gp-Speed
| 10***74 | Seal-Connector | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
143-0539 Starting Motor Gp-Electric
| 10***05 | Cap-Receptacle | 1 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
287-6181 Starting Motor Gp-Electric
| 03***12 | Terminal-Ring; (2-Ga, 1/4-In Screw)(Circuit Breaker) | 1 |
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 3 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
300-1071 Switch Gp-Pressure -Engine Oil
| 03***12 | Terminal-Ring; (2-Ga, 1/4-In Screw)(Circuit Breaker) | 1 |
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 3 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
258-4100 Wiring Gp-Cab
| 15***49 | Cable-Electrical; (03050 mm ) | 0 |
| 15***50 | Cable; (00-Ga, Black)(183-cm Each) | 0 |
| 17***20 | Strap-Dual Clamp | 5 |
258-4192 Wiring Gp-Engine -Battery
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
258-4115 Wiring Gp-Engine
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
336-0913 Wiring Gp-Grade Control
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***39 | Relay As | 5 |
258-4107 Wiring Gp-Machine
| 14***82 | Elbow As | 2 |
| 17***20 | Strap-Dual Clamp | 1 |
| 19***40 | Connector As | 1 |
258-4190 Wiring Gp-Quick Coupler
| 13***04 | Switch As-Pressure; (Power Train Oil Filter Bypass) | 1 |
| 1G***78 | Filter As-Oil; (Advanced Efficiency)(Hydraulic) | 1 |
| 25***90 | Wiring Group-Quick Coupler | 1 |
258-4125 Wiring Gp-Work Tool
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***21 | Connector | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 4 |
Engine Arrangement
295-7114 Engine Ar
| 28***74 | Engine Ar-Primary | 1 |
| 29***14 | Engine Ar | 1 |
| 31***06 | Engine Ar-Primary | 1 |
287-8074 Engine Ar-Primary
| 23***80 | Valve Mechanism Group | 1 |
| 23***95 | Pump Group-Engine Oil | 1 |
| 23***04 | Glow Plug Group | 1 |
319-6806 Engine Ar-Primary
| 23***80 | Valve Mechanism Group | 1 |
| 23***95 | Pump Group-Engine Oil | 1 |
| 23***04 | Glow Plug Group | 1 |
295-7118 Installation Ar-Engine
| 25***47 | Mounting Group-Engine | 1 |
| 25***52 | Drain Group-Engine Oil | 1 |
| 25***65 | Lines Group-Air | 1 |
Frame And Body
258-3810 Conversion Ar-Roading -Germany
| 17***16 | Chock | 1 |
| 25***10 | Conversion Ar-Roading; -Germany | 1 |
| 25***33 | Film-Notice; (Steering) | 1 |
315-6355 Conversion Ar-Roading
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***54 | Fastener; (Loop) (22cm) (X3) | 0 |
| 12***55 | Fastener-Hook; (18-cm Each) | 0 |
258-3812 Conversion Ar-Roading -Italy
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 12***54 | Fastener; (Loop) (22cm) (X3) | 0 |
258-3800 Conversion Ar-Roading -Nacd
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
258-3809 Conversion Ar-Roading -Outside Nacd
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
258-3840 Conversion Gp-Roading -Germany
| 25***40 | Conversion Group-Roading; -Germany | 1 |
| 31***41 | Counterweight | 4 |
| 7X***49 | Bolt (M12x1.75x100mm); (M12x1.75x100-mm) | 4 |
258-3841 Conversion Gp-Roading -Italy
| 14***32 | Pin As | 1 |
| 15***05 | Bolt-Shoulder | 2 |
| 22***40 | Latch As | 1 |
258-2591 Counterweight Gp
| 25***91 | Counterweight Group | 1 |
| 25***78 | Plate As | 1 |
| 25***86 | Plate As | 1 |
322-1644 Door As-Access -Vented
| 25***73 | Frame As | 1 |
| 28***98 | Arm As-Lift, Cylinder Head | 1 |
| 32***44 | Door As-Access; -Vented | 1 |
258-2594 Enclosure Gp-Engine
| 22***15 | Plate As | 1 |
| 24***77 | Bolt; (M8x1.25x12-mm) | 1 |
| 25***94 | Enclosure Group-Engine | 1 |
258-3575 Frame & Mtg Gp-Machine
| 25***75 | Frame & Mtg Group-Machine | 1 |
| 31***41 | Counterweight | 2 |
| 7X***49 | Bolt (M12x1.75x100mm); (M12x1.75x100-mm) | 4 |
258-3574 Frame Gp-Machine
| 25***74 | Frame Group-Machine | 1 |
| 28***67 | Film-Instruction; (Service Chart, Read Omm)(Service Chart) | 1 |
| 28***68 | Film-Instruction; (Service Chart, Read Omm)(Service Chart) | 1 |
150-8621 Guide Gp-Lines
| 12***18 | Seal; (1000-cm) | 0 |
| 13***27 | Seal; (69-cm) | 0 |
| 15***21 | Guide Group-Lines | 1 |
287-4160 Kit-Counterweight
| 08***48 | Lamp; (12-Volt, 5-Watt) | 1 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
312-1024 Kit-Engine Enclosure -Vented
| 17***91 | Nut-Spring | 4 |
| 17***16 | Chock | 1 |
| 25***33 | Film-Notice; (Steering) | 1 |
342-2683 Kit-Machine Enclosure Seal -Debris Barrier
| 17***91 | Nut-Spring | 4 |
| 17***16 | Chock | 1 |
| 17***47 | Pin | 1 |
311-8704 Kit-Machine Enclosure Seal -Debris Barrier
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
333-7435 Kit-Roading Conversion -Italy
| 15***80 | Washer-Hard; (22x38x6-mm Thk) | 8 |
| 25***89 | Mount | 4 |
| 25***91 | Plate-Lift | 4 |
258-3884 Kit-Roading Conversion -Lights, Mirrors
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
333-7434 Kit-Roading Conversion -Germany
| 15***80 | Washer-Hard; (22x38x6-mm Thk) | 8 |
| 25***89 | Mount | 4 |
| 25***92 | Bracket As-Lift | 1 |
333-7436 Kit-Roading Conversion -Front
| 13***66 | Mirror Group-Rear View | 2 |
| 14***71 | Clamp; (Top)(Top) | 1 |
| 14***72 | Clamp; (Bottom)(Bottom) | 1 |
315-7816 Kit-Roading Conversion -Italy
| 15***80 | Washer-Hard; (22x38x6-mm Thk) | 8 |
| 25***91 | Plate-Lift | 4 |
| 31***16 | Kit-Roading Conversion; -Italy | 1 |
315-7815 Kit-Roading Conversion -Germany
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
258-4390 Lifting Gp-Machine -Kit, Single Point
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 15***71 | Kit-Connecting Plug; (4-Pin) | 1 |
| 17***20 | Strap-Dual Clamp | 5 |
258-4385 Lifting Gp-Machine -Four Point
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 15***71 | Kit-Connecting Plug; (4-Pin) | 1 |
258-4410 Lifting Gp-Machine -Kit, Four Point
| 17***79 | Insulation | 1 |
| 25***10 | Lifting Group-Machine; -Kit, Four Point | 1 |
| 26***78 | Insulation | 1 |
258-3872 Mirror & Mtg Gp-Rear View -With Roading Light Mount
| 17***79 | Insulation | 2 |
| 25***72 | Mirror & Mtg Group-Rear View; -With Roading Light Mount | 1 |
| 29***55 | Insulation | 1 |
258-3848 Mounting Gp-Registration -Italian
| 25***48 | Mounting Group-Registration; -Italian | 1 |
| 30***53 | Axle As-Undercarriage; (Lh) | 1 |
| 30***54 | Axle As-Undercarriage; (Rh) | 1 |
307-6237 Mounting Gp-Roading Lights -Kit, Germany, Italy
| 30***47 | Tube As | 1 |
| 30***55 | Name-Plate (Operation; Loader), Bearing-Sleeve, Name-Plate (Loader:Std) | 2 |
| 30***05 | Frame As; (Lh) | 1 |
294-4560 Suppression Gp-Sound -Machine
| 29***60 | Suppression Group-Sound; -Machine | 1 |
| 30***77 | Idler Group-Track | 1 |
| 30***88 | Roller Group-Track | 1 |
258-3496 Suppression Gp-Sound -Machine
| 25***96 | Suppression Group-Sound; -Machine | 1 |
| 30***47 | Tube As | 1 |
| 30***55 | Name-Plate (Operation; Loader), Bearing-Sleeve, Name-Plate (Loader:Std) | 2 |
Fuel System
295-7463 Control Gp-Governor
| 13***87 | Clip | 1 |
| 19***36 | Insert-Threaded; (M6x1-Thd) | 3 |
| 23***96 | Screw-Flat Head; (M6x1x35-mm) | 4 |
295-7465 Control Gp-Governor
| 06***80 | Fitting | 1 |
| 11***01 | Bowl As-Water Collection | 1 |
| 11***18 | Ring-Retaining | 1 |
335-5751 Lines Gp-Fuel
| 09***35 | Cap | 1 |
| 11***63 | Support | 4 |
| 11***64 | Hose | 4 |
295-7029 Lines Gp-Fuel
| 09***35 | Cap | 1 |
| 11***63 | Support | 4 |
| 11***64 | Hose | 4 |
314-9909 Lines Gp-Fuel Injection
| 14***17 | Bolt; (M10x1.25x25-mm) | 1 |
| 19***56 | Clip | 1 |
| 19***33 | Bolt | 1 |
335-5752 Pump Gp-Fuel Injection
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 25***40 | Tank Group-Fuel | 1 |
314-9911 Pump Gp-Fuel Injection
| 14***17 | Bolt; (M10x1.25x25-mm) | 1 |
| 19***56 | Clip | 1 |
| 19***33 | Bolt | 2 |
258-3442 Pump Gp-Fuel Prm & Prim Filter -Water Separator
| 00***64 | Seal-O-Ring | 1 |
| 14***28 | Elbow | 1 |
| 23***37 | Fitting | 1 |
258-2439 Tank & Mtg Gp-Fuel
| 11***58 | Pulley-Alternator | 1 |
| 11***59 | Frame As-Alternator | 1 |
| 11***60 | Rotor As-Alternator | 1 |
258-2440 Tank Gp-Fuel
| 10***14 | Alternator Group-Charging | 1 |
| 23***62 | Plate | 1 |
| 23***73 | Bolt; (M10x1.5x90-mm) | 1 |
Hydraulic System
149-0686 Accumulator Gp-Hydraulic -Charged
| 14***86 | Accumulator Group-Hydraulic; -Charged | 1 |
| 17***58 | Kit-Seal | 1 |
| 21***55 | Rod End As | 1 |
227-8807 Accumulator Gp-Hydraulic -Uncharged
| 02***87 | Fitting-Grease; (Universal Joint) | 2 |
| 22***07 | Accumulator Group-Hydraulic; -Uncharged | 1 |
| 26***40 | Kit-Seal; (Swing Cylinder) | 1 |
231-5274 Cylinder & Mtg Gp-Angle Blade
| 23***74 | Cylinder & Mtg Group-Angle Blade | 1 |
| 25***97 | Bearing-Sleeve | 1 |
| 27***70 | Kit-Seal; (Hydraulic Cylinder) | 1 |
230-5406 Cylinder & Mtg Gp-Angle Blade
| 02***87 | Fitting-Grease; (Universal Joint) | 2 |
| 23***06 | Cylinder & Mtg Group-Angle Blade | 1 |
| 26***40 | Kit-Seal; (Swing Cylinder) | 1 |
293-6264 Cylinder Gp-Bucket
| 21***24 | Kit-Seal; (Lift) | 2 |
| 25***12 | Cylinder Group-Lift | 2 |
| 25***14 | Cylinder Group-Tilt; -Rh | 1 |
255-0943 Cylinder Gp-Grapple
| 21***43 | Fitting As; (Quick Disconnect, Male) | 1 |
| 21***44 | Fitting As; (Quick Disconnect, Male) | 1 |
| 25***43 | Cylinder Group-Grapple | 1 |
278-1975 Cylinder Gp-Grapple -Industrial
| 21***45 | Fitting As; (Quick Disconnect, Female) | 1 |
| 21***46 | Fitting As; (Quick Disconnect, Female) | 1 |
| 27***75 | Cylinder Group-Grapple; -Industrial | 1 |
225-9521 Cylinder Gp-Hydraulic -Angle Blade
| 22***21 | Cylinder Group-Hydraulic; -Angle Blade | 1 |
| 25***76 | Lines Group-Hydraulic | 1 |
274-9930 Cylinder Gp-Hydraulic -Angle Blade
| 25***78 | Lines Group-Hydraulic; -Work Tool Positioner | 1 |
| 25***68 | Manifold & Mtg Group-Control; -Work Tool Positioner | 1 |
| 27***30 | Cylinder Group-Hydraulic; -Angle Blade | 1 |
192-2640 Cylinder Gp-Hydraulic -Coupler
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 30***52 | Tee | 1 |
278-1969 Cylinder Gp-Hydraulic
| 25***22 | Lines Group-Work Tool | 1 |
| 25***02 | Valve & Mtg Group-Control | 1 |
| 25***56 | Pump & Mtg Group-Work Tool | 1 |
274-9931 Cylinder Gp-Hydraulic -Angle Blade
| 25***07 | Pump & Mtg Group-Hydrostatic | 1 |
| 25***11 | Lines Group-Lift Cylinder | 1 |
| 25***12 | Lines Group-Tilt Cylinder | 1 |
258-2512 Cylinder Gp-Lift
| 25***21 | Lines Group-Work Tool; -High Flow | 1 |
| 25***03 | Valve & Mtg Group-Control; -High Flow | 1 |
| 25***12 | Cylinder Group-Lift | 1 |
293-5710 Cylinder Gp-Lift
| 25***22 | Lines Group-Work Tool | 1 |
| 25***02 | Valve & Mtg Group-Control | 1 |
| 25***82 | Lines Group-Hydraulic Fan; -Radiator | 1 |
258-2558 Cylinder Gp-Lift Arm -Radial Lift
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
293-5711 Cylinder Gp-Tilt -Rh
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
258-2514 Cylinder Gp-Tilt -Rh
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
293-5712 Cylinder Gp-Tilt -Lh
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
258-2515 Cylinder Gp-Tilt -Lh
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
285-2190 Fitting Gp-Hydraulic -Manual
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
218-5840 Fitting Gp-Hydraulic -Quick Disconnect, Male, High Flow
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
218-5841 Fitting Gp-Hydraulic -Quick Disconnect, Female, High Flow
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
258-3182 Hydraulic Ar -High Flow
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 16***89 | Hose As | 2 |
258-3733 Hydraulic Ar
| 14***41 | Connector Group | 2 |
| 25***80 | Tube As | 1 |
| 25***81 | Tube As | 1 |
258-3730 Hydraulic Ar
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 16***89 | Hose As | 2 |
258-2428 Hydraulic Ar -Work Tool Positioner
| 14***15 | Connector As | 2 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 6 |
| 14***42 | Connector Group | 2 |
258-2426 Hydraulic Ar
| 14***19 | Connector As | 2 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
258-3180 Hydraulic Ar
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
258-2603 Hydraulic Ar
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
| 13***51 | Spacer; (11x19x6-mm Thk) | 1 |
| 14***25 | Connector As. | 4 |
258-3910 Kit-Quick Coupler Conversion -Hydraulic
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***39 | Relay As | 1 |
| 14***15 | Connector As | 1 |
258-3915 Kit-Work Tool Positioner -Self-Leveling Hydraulics
| 11***61 | Hose As | 1 |
| 14***15 | Connector As | 2 |
| 14***16 | Connector Group | 2 |
154-5052 Lines Gp-Bucket
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
| 14***11 | Plug Group | 1 |
| 15***52 | Lines Group-Bucket; -Multipurpose | 1 |
154-5019 Lines Gp-Bucket
| 11***61 | Hose As | 1 |
| 14***15 | Connector As | 2 |
| 14***16 | Connector Group | 2 |
279-5415 Lines Gp-Bucket -Multipurpose
| 15***49 | Elbow As | 1 |
| 16***67 | Fitting As; (Quick Disconnect, Male)(Quick Disconnect) | 2 |
| 19***08 | Adapter | 1 |
279-5416 Lines Gp-Bucket -Multipurpose
| 11***49 | Fitting As; (Quick Disconnect) | 2 |
| 14***52 | Elbow As. | 1 |
| 14***61 | Elbow Group | 1 |
279-5413 Lines Gp-Bucket -Multipurpose
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
| 15***43 | Connector As. | 1 |
293-0140 Lines Gp-Bucket -Multipurpose
| 06***58 | Clamp | 2 |
| 10***03 | Plate-Cover | 3 |
| 14***93 | Elbow Group | 2 |
285-6113 Lines Gp-Bucket -Utility
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***52 | Elbow As. | 1 |
| 14***61 | Elbow Group | 1 |
279-5414 Lines Gp-Bucket -Multipurpose
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***62 | Elbow Group | 1 |
| 15***49 | Elbow As | 1 |
279-5412 Lines Gp-Bucket -Industrial
| 14***97 | Block | 2 |
| 25***39 | Hose As | 4 |
| 25***64 | Tube As | 1 |
231-5273 Lines Gp-Connecting
| 10***03 | Plate-Cover | 3 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 1 |
| 14***93 | Elbow Group | 2 |
177-1986 Lines Gp-Connecting
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 5 |
258-2424 Lines Gp-Coupler
| 14***86 | Accumulator Group-Hydraulic; -Charged | 1 |
| 19***03 | Elbow As | 1 |
| 19***31 | Elbow; (45-Deg) | 1 |
161-0187 Lines Gp-Grapple
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
| 15***43 | Connector As. | 1 |
286-9250 Lines Gp-Grapple
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
286-9279 Lines Gp-Grapple
| 23***79 | Cover | 1 |
| 25***11 | Manifold Group-Control; -Angling Blade | 1 |
| 28***79 | Lines Group-Grapple | 1 |
258-2878 Lines Gp-Hydraulic -Work Tool Positioner
| 25***01 | Manifold & Solenoid Group-Control; -Work Tool Positioner | 1 |
| 25***78 | Lines Group-Hydraulic; -Work Tool Positioner | 1 |
| 4P***34 | Clip-Ladder; (00800 mm ) | 1 |
258-2876 Lines Gp-Hydraulic
| 25***76 | Lines Group-Hydraulic | 1 |
| 25***60 | Bracket As | 1 |
| 27***64 | Manifold Group-Control; -Motor, 2-Speed | 1 |
258-2786 Lines Gp-Hydraulic Fan
| 18***51 | Washer-Hard; (5.3x8.8x2-mm Thk) | 8 |
| 19***08 | Seal-O-Ring | 1 |
| 21***14 | Seal-O-Ring | 1 |
258-2582 Lines Gp-Hydraulic Fan -Radiator
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 15***79 | Kit-Seal; (Relief Valve, Conveyor Cont) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
258-2780 Lines Gp-Hydraulic Oil Cooler
| 24***81 | Flange | 2 |
| 24***12 | Kit-Seal; (Solenoid Valve) | 1 |
| 25***34 | Valve Group-Solenoid; (Hydraulic Backup Engaged Gear) | 1 |
258-2411 Lines Gp-Lift Cylinder
| 24***81 | Flange | 2 |
| 24***12 | Kit-Seal; (Solenoid Valve) | 1 |
| 25***34 | Valve Group-Solenoid; (Hydraulic Backup Engaged Gear) | 1 |
258-3393 Lines Gp-Lowering Control -Manual
| 10***08 | Kit-Seal; (Solenoid Valve, Quick Steer) | 1 |
| 25***93 | Lines Group-Lowering Control; -Manual | 1 |
| 27***34 | Coil As; (12-Volt) | 2 |
258-3238 Lines Gp-Pump -High Flow
| 15***13 | Plate | 1 |
| 15***41 | Pin | 2 |
| 15***42 | Pin | 2 |
258-3237 Lines Gp-Pump
| 23***28 | Coil As | 1 |
| 25***77 | Motor Group-Gear; (Fan, Demand) | 1 |
| 25***37 | Lines Group-Pump | 1 |
258-2412 Lines Gp-Tilt Cylinder
| 25***12 | Lines Group-Tilt Cylinder | 1 |
| 25***60 | Pump Group-Gear | 1 |
| 27***60 | Washer-Hard; (15x22x2.5-mm Thk) | 4 |
258-2422 Lines Gp-Work Tool
| 10***04 | Bolt; (Socket Head) (M10x1.5x30mm) | 2 |
| 25***22 | Lines Group-Work Tool | 1 |
| 25***54 | Pump Group-Piston; -High Flow | 1 |
258-2421 Lines Gp-Work Tool -High Flow
| 25***21 | Lines Group-Work Tool; -High Flow | 1 |
| 25***53 | Pump Group-Gear | 1 |
| 27***60 | Washer-Hard; (15x22x2.5-mm Thk) | 4 |
258-3462 Manf & Solenoid Mtg Gp-Accum -Pilot Shutoff
| 11***04 | Bolt-Socket Head; (M12x1.75x45-mm) | 4 |
| 23***86 | Kit-Bearing; (Generator Pump) | 1 |
| 23***87 | Kit-Bearing; (Generator Pump) | 1 |
258-3394 Manifold & Lines Gp-Accum
| 10***04 | Bolt; (Socket Head) (M10x1.5x30mm) | 2 |
| 25***54 | Pump Group-Piston; -High Flow | 1 |
| 25***61 | Pump Group-Gear | 1 |
258-3152 Manifold & Lines Gp-Control -Motor, 2-Speed
| 25***35 | Tank Group-Hydraulic | 1 |
| 25***47 | Bracket | 1 |
| 25***49 | Bracket As | 1 |
258-3468 Manifold & Mtg Gp-Control -Work Tool Positioner
| 11***52 | Spacer; (13x25x22.14-mm Thk) | 2 |
| 23***25 | Stud; (M10x1.5-Thd) | 1 |
| 25***06 | Valve Group-Control | 1 |
231-5278 Manifold & Mtg Gp-Control -Angling Blade
| 13***45 | Pad; (Connector) | 1 |
| 14***37 | Cap As-Filler; (Hydraulic Tank) | 1 |
| 23***78 | Manifold & Mtg Group-Control; -Angling Blade | 1 |
258-3463 Manifold & Mtg Gp-Control -Motor, 2-Speed
| 25***04 | Strainer As; (Hydraulic Tank) | 1 |
| 25***63 | Manifold & Mtg Group-Control; -Motor, 2-Speed | 1 |
| 26***90 | Gauge Group-Sight; (Hydraulic Tank) | 1 |
258-2801 Manifold & Solenoid Gp-Control
| 11***52 | Spacer; (13x25x22.14-mm Thk) | 2 |
| 23***25 | Stud; (M10x1.5-Thd) | 1 |
| 25***07 | Valve Group-Control; -High Flow | 1 |
291-0010 Manifold Gp-Control -Quick Coupler
| 11***61 | Seal Kit; (Includes Seals, Thrust Ring, Stem And Connectors) | 1 |
| 20***71 | Valve Group-Manual; (Coupler Pin, Lift Arm Lwr Cont) | 1 |
| 20***73 | Valve Group-Manual; (Coupler Pin, Lift Arm Lwr Cont) | 1 |
274-8564 Manifold Gp-Control -Motor, 2-Speed
| 18***54 | Valve Group-Solenoid; -Auxiliary | 6 |
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 2 |
| 20***71 | Cap | 1 |
258-9011 Manifold Gp-Control -Angling Blade
| 25***11 | Manifold Group-Control; -Angling Blade | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6V***97 | Seal (Later Machines And Field Installed) | 1 |
274-8563 Manifold Gp-Control -Pilot Shutoff
| 00***82 | Spring | 3 |
| 12***16 | Bolt-Shoulder | 1 |
| 14***31 | Valve-Check | 3 |
258-2579 Motor & Mtg Gp-Hydraulic Fan
| 13***76 | Seal-O-Ring | 1 |
| 25***79 | Motor & Mtg Group-Hydraulic Fan | 1 |
156-0891 Mounting Gp-Cylinder
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 21***73 | Nut; (1/2-28-Thd) | 1 |
165-8731 Mounting Gp-Cylinder
| 16***31 | Mounting Group-Cylinder; -Utility | 1 |
| 20***71 | Kit-Seal; (Solenoid Valve) | 1 |
| 21***61 | Flange | 1 |
154-5011 Mounting Gp-Cylinder
| 12***98 | Seat | 1 |
| 12***99 | Seat | 1 |
| 13***49 | Connector | 1 |
286-9248 Mounting Gp-Cylinder -Grapple Bucket
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
| 4K***09 | Bearing-Sleeve | 4 |
| 6K***48 | Bearing-Sleeve | 4 |
258-3402 Pump & Mtg Gp-Gear
| 14***91 | Pin As | 2 |
| 14***94 | Pin | 1 |
| 1H***34 | Ring-Retaining; (External) | 4 |
258-2556 Pump & Mtg Gp-Work Tool
| 15***62 | Film-Information; (Tie-Down Location) | 2 |
| 18***33 | Step Group-Material Handling Arm | 1 |
| 21***50 | Arm As | 1 |
258-2557 Pump & Mtg Gp-Work Tool -High Flow
| 13***86 | Edge Group-Cutting | 1 |
| 17***81 | Blade Group-Angling | 1 |
| 17***83 | Spring Group-Blade | 1 |
258-2554 Pump Gp-Piston -High Flow
| 14***41 | Edge Group-Cutting | 1 |
| 17***82 | Blade Group-Angling | 1 |
| 17***83 | Spring Group-Blade | 1 |
258-3401 Pump Gp-Piston & Gear
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
258-2434 Tank & Mtg Gp-Hydraulic
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
258-2806 Tank Gp-Hydraulic
| 22***21 | Trunnion As | 1 |
| 22***79 | Plate As | 1 |
| 22***28 | Plate As | 1 |
258-2435 Tank Gp-Hydraulic
| 22***21 | Trunnion As | 1 |
| 22***79 | Plate As | 1 |
| 22***28 | Plate As | 1 |
258-2503 Valve & Mtg Gp-Control -High Flow
| 16***89 | Tack-Fastener | 4 |
| 22***12 | Blade As-Angling | 1 |
| 22***46 | Edge Group-Bit & Cutting | 1 |
258-2502 Valve & Mtg Gp-Control
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***40 | Pin | 2 |
| 16***19 | Pin As | 2 |
6e-4701 Valve Gp-Check
| 15***77 | Edge | 1 |
| 6E***01 | Valve Group-Check; -Pilot Oil | 1 |
258-2507 Valve Gp-Control -High Flow
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***80 | Blade Group-Multipurpose Bucket | 1 |
| 16***89 | Tack-Fastener | 4 |
336-1322 Valve Gp-Control -Implement
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***85 | Blade Group-Multipurpose Bucket | 1 |
336-1323 Valve Gp-Control
| 15***37 | Edge | 1 |
| 33***23 | Valve Group-Control | 1 |
258-2506 Valve Gp-Control
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 25***06 | Valve Group-Control | 1 |
112-1817 Valve Gp-Manual
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 15***59 | Edge | 1 |
295-1799 Valve Gp-Relief
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***87 | Blade Group-Multipurpose Bucket | 1 |
211-3014 Valve Gp-Shuttle -High Flow
| 15***77 | Edge | 1 |
| 21***14 | Valve Group-Shuttle; -High Flow | 1 |
195-9700 Valve Gp-Solenoid -12-Volt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 1 |
185-4254 Valve Gp-Solenoid
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 18***54 | Valve Group-Solenoid; -Auxiliary | 1 |
Implements
287-4198 Arm As-Lift
| 19***16 | Edge | 1 |
| 28***98 | Arm As-Lift, Cylinder Head | 1 |
258-2699 Pin Gp-Lift Arm -With Support
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 25***99 | Pin Group-Lift Arm; -With Support | 1 |
Lubrication System
314-9901 Filter Gp-Engine Oil
| 23***94 | Strainer As-Oil; (Engine) | 1 |
| 23***13 | Seal-O-Ring | 1 |
| 31***01 | Filter Group-Engine Oil | 1 |
287-5377 Lines Gp-Engine Oil
| 10***44 | Nut | 1 |
| 10***83 | Seal-O-Ring | 1 |
| 11***41 | Pump As-Oil | 1 |
235-5895 Pump Gp-Engine Oil
| 10***25 | Valve As; (Oil Bypass)(Engine) | 1 |
| 23***96 | Gasket | 1 |
| 23***96 | Gasket | 1 |
287-5665 Valve Gp-Engine Oil Relief
| 09***13 | Seal-O-Ring | 4 |
| 09***21 | Plug | 2 |
| 19***35 | Bolt; (M8x1.25x22-mm) | 13 |
Machine Arrangement
304-1910 Chassis Ar
| 15***21 | Guide Group-Lines | 1 |
| 25***39 | Tank & Mtg Group-Fuel | 1 |
| 25***58 | Cylinder Group-Lift Arm; -Radial Lift | 1 |
304-1879 Common Ar
| 25***03 | Hydraulic Ar | 1 |
| 25***00 | Cab Ar-Enclosed Rops | 1 |
| 29***18 | Installation Ar-Engine | 1 |
342-5009 Control Ar-Machine -On, Off Auxiliary Control
| 25***03 | Control Group-Electrohydraulic; -Lh | 1 |
| 25***05 | Control Group-Electrohydraulic; -Rh | 1 |
| 34***09 | Control Ar-Machine; -On, Off Auxiliary Control | 1 |
342-5010 Control Ar-Machine -Aux Proportional Flow
| 25***03 | Control Group-Electrohydraulic; -Lh | 1 |
| 25***06 | Control Group-Electrohydraulic; -Rh | 1 |
| 34***10 | Control Ar-Machine; -Auxiliary Proportional Flow | 1 |
342-5011 Control Ar-Machine -Aux Proportional Flow
| 25***04 | Control Group-Electrohydraulic; -Lh, High Flow | 1 |
| 25***06 | Control Group-Electrohydraulic; -Rh | 1 |
| 25***25 | Wiring Group-Work Tool | 1 |
304-1911 Machine Ar-Special
| 25***26 | Hydraulic Ar | 1 |
| 25***52 | Manifold & Lines Group-Control; -Motor, 2-Speed | 1 |
| 25***60 | Lines Group-Parking Brake | 1 |
304-1913 Machine Ar-Special
| 25***28 | Hydraulic Ar; -Work Tool Positioner | 1 |
| 25***52 | Manifold & Lines Group-Control; -Motor, 2-Speed | 1 |
| 25***60 | Lines Group-Parking Brake | 1 |
304-1912 Machine Ar-Special
| 25***28 | Hydraulic Ar; -Work Tool Positioner | 1 |
| 25***52 | Manifold & Lines Group-Control; -Motor, 2-Speed | 1 |
| 25***60 | Lines Group-Parking Brake | 1 |
Operator Station
258-4229 Accessory Gp-Cab
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 7 |
186-6190 Accumulator Gp-Refrigerant -Charged
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
176-3900 Accumulator Gp-Refrigerant -Uncharged
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 2 |
| 17***00 | Accumulator Group-Refrigerant; -With Desiccant | 1 |
258-4261 Air Conditioner & Mounting Gp
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 21***89 | Screw; (M4x25-mm) | 3 |
| 25***37 | Boot | 1 |
258-4260 Air Conditioner Ar
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
258-4290 Air Conditioner Gp
| 25***27 | Screw-Truss Head; (No 12x17.46-mm) | 2 |
| 25***28 | Plate | 1 |
| 25***94 | Insulation | 1 |
258-4311 Armrest & Mounting Gp
| 10***56 | Plug; (Switch) | 6 |
| 25***33 | Cover; (Cluster) | 1 |
| 25***11 | Armrest & Mounting Group | 1 |
269-0258 Base As-Joystick -Lh
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 2 |
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
269-0257 Base As-Joystick -Rh
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 2 |
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
258-3742 Cab Ar-Enclosed Rops
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
258-4000 Cab Ar-Enclosed Rops
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
258-3680 Cab Ar-Enclosed Rops
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 2 |
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
298-7198 Cable Gp-Control -Manual Lowering
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
276-0074 Cable Gp-Control
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
258-2468 Compressor & Mtg Gp-Refrig
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
266-2425 Condenser & Mtg Gp-Refrigerant
| 14***71 | Louver As | 6 |
| 16***55 | Bolt; (M6x1x35-mm) | 2 |
| 20***85 | Bolt; (M8x1.25x35-mm) | 1 |
258-4280 Condenser & Mtg Gp-Refrigerant
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
266-2430 Control & Wiring Gp-Air & Temp
| 15***80 | Washer-Hard; (22x38x6-mm Thk) | 8 |
| 25***89 | Mount | 4 |
| 25***98 | Film-Certification; (Ops, Read Omm) | 1 |
258-4299 Control Gp-Air & Temperature
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 3 |
| 10***56 | Plug; (Switch) | 1 |
| 15***71 | Kit-Connecting Plug; (4-Pin) | 1 |
258-3404 Control Gp-Electrohydraulic -Lh, High Flow
| 10***74 | Seal-Connector | 3 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
258-3405 Control Gp-Electrohydraulic -Rh
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 15***71 | Kit-Connecting Plug; (4-Pin) | 1 |
258-3406 Control Gp-Electrohydraulic -Rh
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 16***72 | Speaker As-Radio | 2 |
| 17***37 | Connector; (Radio) | 1 |
258-3403 Control Gp-Electrohydraulic -Lh
| 25***03 | Control Group-Electrohydraulic; -Lh | 1 |
| 25***46 | Wiring Group-Heater | 1 |
| 25***51 | Heater & Mtg Group-Cab | 1 |
258-3407 Control Gp-Electrohydraulic -Rh, High Flow
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 16***72 | Speaker As-Radio | 2 |
| 17***37 | Connector; (Radio) | 1 |
272-1790 Control Gp-Handle -Lh
| 00***10 | Elbow | 1 |
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 2 |
| 10***74 | Seal-Connector | 2 |
269-0265 Control Gp-Joystick -Lh, High Flow
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
269-0266 Control Gp-Joystick -Lh
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
269-0264 Control Gp-Joystick -Rh
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
269-0262 Control Gp-Joystick -Rh
| 12***70 | Screw-Machine; (M6x1x40-mm) | 3 |
| 17***91 | Nut-Spring | 3 |
| 25***79 | Knob As | 1 |
269-0263 Control Gp-Joystick -Rh, High Flow
| 10***96 | Clip | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***11 | Support | 1 |
258-4245 Cover Gp-Cab
| 00***10 | Elbow | 1 |
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 2 |
| 10***74 | Seal-Connector | 2 |
258-4314 Cover Gp-Console -Rh, Lh
| 25***85 | Window Group-Cab; -Side, Lh | 1 |
| 25***86 | Window Group-Cab; -Side, Rh | 1 |
| 25***14 | Cover Group-Console; -Rh, Lh | 1 |
258-4009 Cover Gp-Instrument Panel
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 25***09 | Cover Group-Instrument Panel | 1 |
| 26***33 | Switch As-Rocker; (Control Pattern Change) | 1 |
258-4070 Door & Mtg Gp-Cab -With Cab Tilt Gas Spring
| 25***70 | Door & Mtg Group-Cab; -With Cab Tilt Gas Spring | 1 |
| 28***81 | Spacer,10.4mm Id X 22mm Od X 35mm L; Spacing Bar, Spacer,10.4mm Id X 22mm Od X 35mm L, Film-Instruction; (Control Pattern, Rh) | 1 |
| 28***82 | Film-Instruction; (Control Pattern, Lh) | 1 |
258-4440 Door & Mtg Gp-Cab -With Cab Tilt Gas Spring
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 13***42 | Screw-Self-Tapping; (M5x2.3x18.8-mm) | 4 |
| 25***40 | Door & Mtg Group-Cab; -With Cab Tilt Gas Spring | 1 |
258-4080 Door & Mtg Gp-Cab -With Cab Tilt Gas Spring
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 13***42 | Screw-Self-Tapping; (M5x2.3x18.8-mm) | 4 |
| 25***80 | Door & Mtg Group-Cab; -With Cab Tilt Gas Spring | 1 |
258-4086 Door Gp-Cab -Glass
| 12***78 | Locknut; (M6x1-Thd) | 1 |
| 25***46 | Lever Group-Governor | 1 |
| 25***47 | Cable As | 1 |
258-4087 Door Gp-Cab -Polycarbonate
| 11***27 | Screw-Machine; (M6x1x30-mm) | 2 |
| 13***27 | Seal; (69-cm) | 0 |
| 17***22 | Seal; (230-cm Each) | 0 |
258-4442 Door Gp-Cab
| 10***96 | Clip | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***11 | Support | 1 |
258-4252 Duct & Filter Gp-Cab Air
| 00***10 | Elbow | 1 |
| 13***53 | Hose; (192.5cm) (X2) | 0 |
| 17***20 | Strap-Dual Clamp | 3 |
258-4400 Guard Gp-Rops/Fops -Kit
| 25***00 | Guard Group-Rops/Fops; -Kit | 1 |
| 5P***58 | Sleeve; (Cable Splice) | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
298-7197 Handle Gp
| 28***70 | Mirror As; (Rear View) | 1 |
| 29***97 | Handle Group | 1 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 1 |
258-4251 Heater & Mtg Gp-Cab
| 21***84 | Mirror As | 1 |
| 25***51 | Heater & Mtg Group-Cab | 1 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 1 |
258-4250 Heater Ar-Cab
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 4 |
| 25***50 | Heater Ar-Cab | 1 |
258-4270 Heater Gp-Cab
| 13***40 | Locknut; (M8x1.25-Thd) | 2 |
| 21***52 | Screw-Truss Head; (M8x1.25x30-mm) | 2 |
| 25***70 | Heater Group-Cab | 1 |
337-3991 Installation Gp-Radio -Kit
| 25***17 | Spring Group-Gas; -Includes Lift Handle | 1 |
| 25***66 | Installation Group-Radio | 1 |
| 25***29 | Accessory Group-Cab | 1 |
258-4066 Installation Gp-Radio
| 09***65 | Spacer; (17x40x3-mm Thk) | 2 |
| 16***95 | Washer; (16.5x71.5x3-mm Thk) | 4 |
| 19***37 | Insert-Threaded; (M8x1.25-Thd) | 1 |
350-9038 Kit-Air Cond & Heater Instl
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 13***42 | Screw-Self-Tapping; (M5x2.3x18.8-mm) | 4 |
| 26***20 | Switch As-Rocker; (Creeper Control) | 1 |
258-2474 Kit-Air Cond & Heater Instl
| 08***77 | Lamp Group-Dome; (12-Volt) | 1 |
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 74 |
| 09***34 | Terminal-Blade; (18-Ga To 22-Ga) | 4 |
350-9039 Kit-Air Cond & Heater Instl
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 4 |
| 12***78 | Locknut; (M6x1-Thd) | 1 |
| 16***54 | Kit-Service; (Pedal) | 1 |
305-8044 Kit-Air Conditioner Breather
| 25***43 | Pedal Group-Governor | 1 |
| 25***73 | Cable As; (Hand Control) | 1 |
| 28***44 | Cable As; (Low Idle) | 1 |
258-2475 Kit-Air Conditioner Instl -Conversion
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 4 |
| 12***78 | Locknut; (M6x1-Thd) | 1 |
| 16***54 | Kit-Service; (Pedal) | 1 |
258-2473 Kit-Cab Door & Mounting -Glass
| 25***73 | Kit-Cab Door & Mounting; -Glass | 1 |
| 25***73 | Cable As; (Hand Control) | 1 |
| 2R***64 | Ring-Retaining | 1 |
258-4443 Kit-Cab Door & Mounting
| 19***54 | Sleeve | 1 |
| 25***43 | Kit-Cab Door & Mounting | 1 |
280-6084 Kit-Cab Door & Mounting -Polycarbonate
| 13***90 | Bushing; (Radio Mount) | 1 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***37 | Connector; (Radio) | 1 |
280-6077 Kit-Cab Heater & Mounting
| 19***54 | Sleeve | 1 |
| 28***77 | Kit-Cab Heater & Mounting | 1 |
258-2472 Kit-Cab Window -Side
| 13***66 | Lead-Antenna | 1 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***17 | Support-Radio | 1 |
258-4110 Kit-Control Pattern Change -Selectable
| 19***54 | Sleeve | 1 |
| 25***10 | Kit-Control Pattern Change; -Selectable | 1 |
292-7927 Kit-Control Pattern Change -Dedicated
| 19***54 | Sleeve | 1 |
| 29***27 | Kit-Control Pattern Change; -Dedicated | 1 |
258-4111 Kit-Instrument Panel -Includes Creeper Control, Rh
| 13***90 | Bushing; (Radio Mount) | 1 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***37 | Connector; (Radio) | 1 |
258-4045 Lever Gp-Governor
| 13***90 | Bushing; (Radio Mount) | 1 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***37 | Connector; (Radio) | 1 |
327-8941 Lever Gp-Governor
258-4020 Liner Gp-Cab
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 16***72 | Speaker As-Radio | 2 |
| 17***37 | Connector; (Radio) | 1 |
258-4433 Liner Gp-Cab
| 25***55 | Seat Group-Suspension; -Air | 1 |
| 25***11 | Armrest & Mounting Group | 1 |
| 25***33 | Liner Group-Cab | 1 |
258-4265 Lines Gp-Air Conditioner
| 25***54 | Seat Group-Suspension; -Mechanical | 1 |
| 25***65 | Lines Group-Air Conditioner | 1 |
| 25***11 | Armrest & Mounting Group | 1 |
258-4255 Lines Gp-Heater
| 15***83 | Washer-Hard; (8.4x35x2.5-mm Thk) | 4 |
| 25***55 | Lines Group-Heater | 1 |
| 25***02 | Seat & Armrest Group; -Suspension | 1 |
6v-1970 Literature Gp
| 15***83 | Washer-Hard; (8.4x35x2.5-mm Thk) | 4 |
| 25***01 | Seat & Armrest Group | 1 |
| 6V***70 | Literature Group; (Literature Compartment) | 1 |
258-4230 Mirror Gp-Rear View
| 25***51 | Seat & Mounting Group; -Suspension | 1 |
| 25***30 | Mirror Group-Rear View | 1 |
| 25***14 | Cover Group-Console; -Rh, Lh | 1 |
305-8034 Mirror Gp-Rear View
| 25***52 | Seat & Mounting Group | 1 |
| 25***14 | Cover Group-Console; -Rh, Lh | 1 |
| 30***34 | Mirror Group-Rear View | 1 |
330-5011 Motor Gp-Window Wiper
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
| 33***11 | Motor Group-Window Wiper | 1 |
| 8S***34 | Locknut; (Flange) (7/16-20 Thd) | 2 |
295-3171 Mounting Gp-Armrest -Lh
| 29***71 | Mounting Group-Armrest; -Lh | 1 |
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
| 8S***34 | Locknut; (Flange) (7/16-20 Thd) | 2 |
295-3172 Mounting Gp-Armrest -Rh
| 09***68 | Washer; (5x16x1.2-mm Thk) | 2 |
| 11***26 | Screw; (Pan Head) (10-16x0.63 In) | 2 |
| 13***90 | Bolt-Carriage; (M8x1.25x30-mm) | 2 |
258-4220 Mounting Gp-Rops -Includes Step
| 09***68 | Washer; (5x16x1.2-mm Thk) | 2 |
| 11***26 | Screw; (Pan Head) (10-16x0.63 In) | 2 |
| 13***90 | Bolt-Carriage; (M8x1.25x30-mm) | 2 |
258-3740 Option Ar-Cab
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 4 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
258-4162 Panel Gp-Instrument
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 4 |
| 1P***10 | Washer; (0.391x0.812x0.067-In Thk) | 4 |
| 25***62 | Panel Group-Instrument | 1 |
258-4163 Panel Gp-Instrument -Rh
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***11 | Screw-Machine; (3/8-16x0.75-In) | 1 |
280-6342 Pedal Gp-Governor
| 17***91 | Nut-Spring | 4 |
| 25***33 | Visor Group-Cab; -Lh | 1 |
| 27***42 | Screw-Truss Head; (M6x1x20-mm) | 4 |
325-8383 Pedal Gp-Governor
| 1D***77 | Bolt-Round Head; (3/8-16x1-In) | 2 |
| 32***83 | Pedal Group-Governor | 1 |
| 5T***69 | Clamp | 2 |
258-4043 Pedal Gp-Governor
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 2 |
| 09***78 | Pin-Spring | 1 |
| 14***08 | Fastener | 13 |
327-8937 Pedal Gp-Governor
| 25***83 | Window As; (Lh Front Sliding Glass) | 1 |
| 25***84 | Window As; (Lh Rear Sliding Glass) | 1 |
| 25***65 | Latch As | 1 |
284-8955 Radio Gp -Am/Fm/Wb/Sirius/ Cd Player
| 12***59 | Clamp-Hose | 2 |
| 12***71 | Clamp-Hose | 1 |
| 18***07 | Clamp-Hose | 1 |
331-5291 Radio Gp -Am/Fm/Wb/Cd Player
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
| 21***02 | Film-Warning; (No Weld, No Drill, Read Omm) | 1 |
337-3992 Radio Gp -Am/Fm
| 19***10 | Film-Identification; (Synthetic Hydraulic Oil, Read Omm) | 2 |
| 33***92 | Radio Group; -Am/Fm | 1 |
331-5292 Radio Gp -Am, Fm
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
| 21***02 | Film-Warning; (No Weld, No Drill, Read Omm) | 1 |
233-3123 Radio Gp -Am/Fm/Wb
| 10***57 | Strip; (Locking) (275cm) | 0 |
| 10***56 | Seal; (275cm) | 0 |
| 23***23 | Radio Group; -Am/Fm/Wb | 1 |
241-4936 Radio Gp -Am/Fm/Wb/Cd Player
| 24***36 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
| 25***85 | Window Group-Cab; -Side, Lh | 1 |
| 25***86 | Window Group-Cab; -Side, Rh | 1 |
262-9163 Radio Gp -Am/Fm Cassette
| 25***31 | Film-Identification; (High Flow Xps) | 2 |
| 26***63 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
200-5729 Radio Gp -Am/Fm/Wb
| 20***29 | Radio Group; -Am/Fm/Wb | 1 |
| 25***82 | Frame As; (Rh) | 1 |
| 25***65 | Latch As | 1 |
284-8953 Radio Gp -Am/Fm/Wb/Cd Player
| 28***53 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
| 29***10 | Film-Identification; (Two Speed) | 2 |
288-1744 Radio Gp -Am/Fm/Wb/Cd Player
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
| 15***35 | Film-Warning; (Crush Hazard, Stay Back) | 1 |
| 22***42 | Film-Warning; (Crush Hazard, Stay Back, U.S.) | 2 |
284-8954 Radio Gp -Am/Fm/Wb/Xm/ Cd Player
| 25***23 | Film-Identification; (Caterpillar) | 1 |
| 25***24 | Film-Identification; (Cat, Lh) | 1 |
| 25***25 | Film-Identification; (Cat, Rh) | 1 |
258-4402 Seat & Armrest Gp -Suspension
| 25***02 | Seat & Armrest Group; -Suspension | 1 |
258-4401 Seat & Armrest Gp
| 25***01 | Seat & Armrest Group | 1 |
258-4052 Seat & Mounting Gp
| 25***52 | Seat & Mounting Group | 1 |
258-4051 Seat & Mounting Gp -Suspension
| 25***51 | Seat & Mounting Group; -Suspension | 1 |
258-4320 Seat Ar-Suspension -Mechanical
| 25***20 | Seat Ar-Suspension; -Mechanical | 1 |
258-4330 Seat Ar-Suspension -Air
| 25***30 | Seat Ar-Suspension; -Air | 1 |
258-4095 Seat Belt Gp -Retractable
| 25***95 | Seat Belt Group; -Retractable | 1 |
258-4096 Seat Belt Gp -Retractable
| 25***96 | Seat Belt Group; -Retractable | 1 |
273-5913 Seat Gp -Cloth, Suspension
| 27***13 | Seat Group; -Cloth, Suspension | 1 |
305-7096 Seat Gp -Vinyl
| 30***96 | Seat Group; -Vinyl | 1 |
258-4055 Seat Gp-Suspension -Air
| 25***55 | Seat Group-Suspension; -Air | 1 |
258-4054 Seat Gp-Suspension -Mechanical
| 25***54 | Seat Group-Suspension; -Mechanical | 1 |
258-4017 Spring Gp-Gas -Includes Lift Handle
| 25***17 | Spring Group-Gas; -Includes Lift Handle | 1 |
273-9611 Suspension Gp-Seat -Mechanical
| 27***11 | Suspension Group-Seat; -Mechanical | 1 |
273-5914 Suspension Gp-Seat -Air
| 27***14 | Suspension Group-Seat; -Air | 1 |
258-4233 Visor Gp-Cab -Lh
| 25***33 | Visor Group-Cab; -Lh | 1 |
258-3497 Visor Gp-Cab
| 25***97 | Visor Group-Cab | 1 |
258-3285 Window Gp-Cab -Side, Lh
| 25***85 | Window Group-Cab; -Side, Lh | 1 |
258-4010 Window Gp-Cab
| 25***10 | Window Group-Cab | 1 |
258-4090 Window Gp-Cab -Side
| 25***90 | Window Group-Cab; -Side | 1 |
258-3286 Window Gp-Cab -Side, Rh
| 25***86 | Window Group-Cab; -Side, Rh | 1 |
Power Train
258-2581 Filter & Lines Gp-Hydraulic
| 17***87 | Connector As | 1 |
| 1F***67 | Clip 7t***28 Cable As To Fan Shroud | 2 |
| 25***81 | Filter & Lines Group-Hydraulic | 1 |
223-9974 Filter Gp-Oil -Hydraulic
| 10***93 | Poppet | 1 |
| 14***27 | Connector Group | 2 |
| 14***62 | Elbow Group | 1 |
258-3960 Lines Gp-Hydrostatic
| 10***93 | Poppet | 1 |
| 14***27 | Connector Group | 2 |
| 14***07 | Plug; (Hex Head) (-6 Orb) (Current) (16***35 Friction Disc Interchangeable With 11***47) (Use All Of One Part Number) | 1 |
258-3860 Lines Gp-Parking Brake
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 4 |
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 2 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 4 |
258-2589 Manifold Gp-Return
| 25***89 | Manifold Group-Return | 1 |
| 27***23 | Kit-Cover | 1 |
| 27***25 | Kit-Duo-Cone Seal | 1 |
304-1860 Motor & Mtg Gp-Hydrostatic
| 09***94 | Ring-Retaining | 1 |
| 16***42 | Washer-Hard; (14.8x27x3-mm Thk) | 2 |
| 16***39 | Bolt; (M14x2x40-mm) | 2 |
307-3045 Motor Gp-Piston
| 27***36 | Kit-Seal; (Piston Pump) | 1 |
| 27***37 | Valve Group-Pump Control | 2 |
| 27***38 | Kit-Piston | 2 |
258-3318 Mounting Gp-Pump
| 25***18 | Mounting Group-Pump | 1 |
| 30***16 | Sprocket-Track | 1 |
| 3E***56 | Washer-Hard; (17.5x30x6-mm Thk) | 12 |
258-2407 Pump & Mtg Gp-Hydrostatic
| 25***07 | Pump & Mtg Group-Hydrostatic | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
| 25***79 | Motor & Mtg Group-Hydraulic Fan | 1 |
258-2405 Pump Gp-Piston -Hydrostatic
| 25***05 | Pump Group-Piston; -Hydrostatic | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
| 25***79 | Motor & Mtg Group-Hydraulic Fan | 1 |
304-1918 Sprocket Gp
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 25***62 | Muffler & Mounting Group | 1 |
Service Equipment And Supplies
289-0848 Film Gp -2-Speed
| 28***48 | Film Group; -2-Speed | 1 |
304-1962 Film Gp
| 30***62 | Film Group | 1 |
258-3230 Film Gp -High Flow Xps
| 25***30 | Film Group; -High Flow Xps | 1 |
348-6735 Kit-Muffler
| 34***35 | Kit-Muffler | 1 |
304-1863 Plate & Film Gp
| 30***63 | Plate & Film Group | 1 |
286-9251 Plate & Film Gp
| 28***51 | Plate & Film Group | 1 |
247-0678 Plate & Film Gp
| 24***78 | Plate & Film Group | 1 |
304-1861 Plate & Film Gp
| 30***61 | Plate & Film Group | 1 |
304-5237 Plate & Film Gp
| 30***37 | Plate & Film Group | 1 |
Undercarriage
304-1850 Axle Gp-Undercarriage
| 30***50 | Axle Group-Undercarriage | 1 |
| 30***78 | Idler Group-Track | 1 |
| 8T***39 | Washer; (6.0mm Thk)(M21.5x6x45mm) | 2 |
356-2463 Frame Gp-Track Roller -Lh
| 16***66 | Toric Ring | 2 |
| 17***82 | Seal Group-Duo-Cone | 2 |
| 30***75 | Collar-Seal | 1 |
304-1904 Frame Gp-Track Roller -Rh
| 30***94 | Idler Group-Track | 1 |
| 30***04 | Frame Group-Track Roller; -Rh | 1 |
| 8T***39 | Washer; (6.0mm Thk)(M21.5x6x45mm) | 2 |
304-1903 Frame Gp-Track Roller -Lh
| 16***66 | Toric Ring | 2 |
| 17***82 | Seal Group-Duo-Cone | 2 |
| 30***75 | Collar-Seal | 1 |
356-2467 Frame Gp-Track Roller -Rh
| 30***25 | Plate | 4 |
| 30***39 | Tape (Accent Stripe), Spacer | 4 |
| 35***67 | Frame Group-Track Roller; -Rh | 1 |
304-1908 Idler Gp-Front
| 30***90 | Roller Group-Track; -Triple Flange | 1 |
| 30***08 | Idler Group-Front | 1 |
| 8T***39 | Washer; (6.0mm Thk)(M21.5x6x45mm) | 2 |
304-1894 Idler Gp-Track
| 30***88 | Roller Group-Track | 4 |
| 30***93 | Manifold, Idler Group-Track | 1 |
| 30***94 | Idler Group-Track | 1 |
304-1893 Idler Gp-Track
| 30***88 | Roller Group-Track | 4 |
| 30***93 | Manifold, Idler Group-Track | 2 |
| 30***98 | Track Adjuster & Recoil Group | 1 |
304-1877 Idler Gp-Track
| 10***88 | Ring-Retaining | 2 |
| 17***83 | Seal Group-Duo-Cone | 2 |
| 21***42 | Ring-Toric | 2 |
304-1878 Idler Gp-Track
| 09***59 | Pin-Cotter | 1 |
| 22***82 | Seal-Wiper | 1 |
| 23***92 | Fitting-Grease | 1 |
304-1852 Mounting Gp-Axle
| 30***52 | Mounting Group-Axle | 1 |
| 30***60 | Motor & Mtg Group-Hydrostatic | 1 |
| 30***01 | Undercarriage Ar; -Lh | 1 |
304-1890 Roller Gp-Track -Triple Flange
| 30***90 | Roller Group-Track; -Triple Flange | 1 |
304-1888 Roller Gp-Track
| 30***88 | Roller Group-Track | 1 |
304-1898 Track Adjuster & Recoil Gp
| 06***43 | Ring-Snap | 1 |
| 21***55 | Pin As | 1 |
| 21***43 | Bushing | 1 |
304-1919 Undercarriage Ar
| 25***97 | Bearing-Sleeve | 1 |
| 28***91 | Kit-Seal | 1 |
| 2K***21 | Locknut (5/8-18 Thd) | 1 |
304-1901 Undercarriage Ar -Lh
| 23***66 | Pin As | 6 |
| 23***99 | Spacer; (25.4x28.4x13-mm Thk) | 12 |
| 24***70 | Spacer; (8.2x13x6-mm Thk) | 6 |
356-2462 Undercarriage Ar -Lh
| 25***97 | Bearing-Sleeve | 1 |
| 25***42 | Bearing-Sleeve | 1 |
| 27***70 | Kit-Seal; (Hydraulic Cylinder) | 1 |
304-1902 Undercarriage Ar -Rh
| 26***41 | Kit-Seal | 1 |
| 30***02 | Undercarriage Ar; -Rh | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
356-2465 Undercarriage Ar -Rh
| 35***65 | Undercarriage Ar; -Rh | 1 |
Work Tools
216-8756 Arm Gp-Material Handling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 21***56 | Arm Group-Material Handling | 1 |
177-1989 Blade Ar -Angling
| 15***37 | Edge | 1 |
| 17***89 | Blade Ar; -Angling | 1 |
| 32***34 | Guard As; (60-In) | 1 |
177-1990 Blade Ar -Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 17***90 | Blade Ar; -Angling | 1 |
231-5277 Blade Ar -Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 23***77 | Blade Ar; -Angling | 1 |
231-5275 Blade Ar -Angling
| 15***59 | Edge | 1 |
| 23***75 | Blade Ar; -Angling | 1 |
| 32***44 | Guard As; (66-In) | 1 |
222-7412 Blade As-Angling
| 19***16 | Edge | 1 |
| 22***12 | Blade As-Angling | 1 |
| 32***64 | Guard As; (78-In) | 1 |
230-4596 Blade As-Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 23***96 | Blade As-Angling | 1 |
177-1987 Blade As-Angling
| 15***77 | Edge | 1 |
| 17***87 | Blade As-Angling | 1 |
| 32***54 | Guard As; (72-In) | 1 |
177-1988 Blade As-Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 17***88 | Blade As-Angling | 1 |
177-1982 Blade Gp-Angling
| 13***87 | Edge Group-Cutting | 1 |
| 17***82 | Blade Group-Angling | 1 |
| 26***84 | Bucket Group-Dirt | 1 |
231-5276 Blade Gp-Angling
| 13***84 | Edge Group-Cutting | 1 |
| 23***76 | Blade Group-Angling | 1 |
| 27***37 | Bucket As-Dirt | 1 |
177-1981 Blade Gp-Angling
| 17***81 | Blade Group-Angling | 1 |
| 29***44 | Edge | 1 |
| 32***74 | Guard As; (84-In) | 1 |
222-7724 Blade Gp-Angling
| 13***83 | Edge Group-Cutting | 1 |
| 22***24 | Blade Group-Angling | 1 |
| 27***34 | Bucket As-Dirt | 1 |
325-7078 Blade Gp-Multipurpose Bucket
| 28***01 | Bucket Ar-Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
| 32***78 | Blade Group-Multipurpose Bucket | 1 |
325-7039 Blade Gp-Multipurpose Bucket
| 15***86 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
325-7049 Blade Gp-Multipurpose Bucket
| 13***85 | Edge Group-Cutting | 1 |
| 15***24 | Bucket Ar-Grapple | 1 |
| 32***49 | Blade Group-Multipurpose Bucket | 1 |
325-7058 Blade Gp-Multipurpose Bucket
| 13***86 | Edge Group-Cutting | 1 |
| 15***25 | Bucket Ar-Grapple; -Industrial | 1 |
| 32***58 | Blade Group-Multipurpose Bucket | 1 |
325-7069 Blade Gp-Multipurpose Bucket
| 28***00 | Bucket Ar-Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
| 32***69 | Blade Group-Multipurpose Bucket | 1 |
279-5395 Blade Gp-Multipurpose Bucket
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5387 Blade Gp-Multipurpose Bucket
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5384 Blade Gp-Multipurpose Bucket
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7068 Blade Gp-Multipurpose Bucket
| 13***87 | Edge Group-Cutting | 1 |
| 21***29 | Bucket Ar-Grapple | 1 |
| 32***68 | Blade Group-Multipurpose Bucket | 1 |
325-7048 Blade Gp-Multipurpose Bucket
| 13***84 | Edge Group-Cutting | 1 |
| 15***23 | Bucket Ar-Grapple | 1 |
| 32***48 | Blade Group-Multipurpose Bucket | 1 |
279-5388 Blade Gp-Multipurpose Bucket
| 13***86 | Edge Group-Cutting | 1 |
| 27***72 | Bucket As-General Purpose | 1 |
| 27***88 | Blade Group-Multipurpose Bucket | 1 |
159-5345 Blade Gp-Multipurpose Bucket
| 13***86 | Edge Group-Cutting | 1 |
| 15***45 | Blade Group-Multipurpose Bucket | 1 |
| 28***89 | Bucket As-Dirt | 1 |
279-5406 Blade Gp-Multipurpose Bucket
| 19***24 | Edge Group-Cutting | 1 |
| 27***06 | Blade Group-Multipurpose Bucket | 1 |
| 29***70 | Bucket As-General Purpose; -High Capacity | 1 |
154-5080 Blade Gp-Multipurpose Bucket
| 13***85 | Edge Group-Cutting | 1 |
| 15***80 | Blade Group-Multipurpose Bucket | 1 |
| 27***40 | Bucket As-Dirt | 1 |
279-5405 Blade Gp-Multipurpose Bucket
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7059 Blade Gp-Multipurpose Bucket
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
| 21***28 | Bucket Group-Grapple | 1 |
159-5347 Blade Gp-Multipurpose Bucket
| 13***84 | Edge Group-Cutting | 1 |
| 15***47 | Blade Group-Multipurpose Bucket | 1 |
| 27***64 | Bucket As-General Purpose | 1 |
279-5396 Blade Gp-Multipurpose Bucket
| 13***87 | Edge Group-Cutting | 1 |
| 27***76 | Bucket As-General Purpose | 1 |
| 27***96 | Blade Group-Multipurpose Bucket | 1 |
325-7038 Blade Gp-Multipurpose Bucket
| 15***85 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
325-7079 Blade Gp-Multipurpose Bucket
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
| 28***51 | Plate & Film Group | 1 |
| 28***78 | Bucket Group-Grapple | 1 |
293-0142 Blade Gp-Multipurpose Bucket
| 15***84 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
279-5385 Blade Gp-Multipurpose Bucket
| 13***85 | Edge Group-Cutting | 1 |
| 27***68 | Bucket As-General Purpose | 1 |
| 27***85 | Blade Group-Multipurpose Bucket | 1 |
279-5438 Bucket Ar-Dirt
| 13***87 | Edge Group-Cutting | 1 |
| 27***24 | Bucket As-Light Material | 1 |
| 27***38 | Bucket Ar-Dirt | 1 |
279-5441 Bucket Ar-Dirt
| 19***24 | Edge Group-Cutting | 1 |
| 27***29 | Bucket As-Light Material | 1 |
| 27***41 | Bucket Ar-Dirt | 1 |
279-5435 Bucket Ar-Dirt
| 13***86 | Edge Group-Cutting | 1 |
| 27***21 | Bucket As-Light Material | 1 |
| 27***35 | Bucket Ar-Dirt | 1 |
285-6090 Bucket Ar-Dirt
| 28***90 | Bucket Ar-Dirt, Turbocharger | 1 |
| 29***23 | Bucket As-Light Material, Wheel Disc | 1 |
| 29***80 | Edge Group-Cutting | 1 |
268-4083 Bucket Ar-Dirt
| 26***83 | Bucket Ar-Dirt | 1 |
| 28***44 | Bucket Group-Grapple | 1 |
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
279-5374 Bucket Ar-General Purpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
296-8192 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5378 Bucket Ar-General Purpose
| 13***85 | Edge Group-Cutting | 1 |
| 27***78 | Bucket Ar-General Purpose | 1 |
| 27***90 | Bucket Ar-Multipurpose | 1 |
279-5366 Bucket Ar-General Purpose
| 15***09 | Bucket Group-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***52 | Lines Group-Bucket; -Multipurpose | 1 |
279-5370 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5373 Bucket Ar-General Purpose
| 13***84 | Edge Group-Cutting | 1 |
| 27***73 | Bucket Ar-General Purpose | 1 |
| 27***82 | Bucket Ar-Multipurpose | 1 |
279-5377 Bucket Ar-General Purpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
279-5365 Bucket Ar-General Purpose
| 15***05 | Bucket Group-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***19 | Lines Group-Bucket; -Multipurpose | 1 |
279-5369 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 15***04 | Bucket Ar-Multipurpose | 1 |
286-9300 Bucket Ar-Grapple
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
286-9301 Bucket Ar-Grapple
| 13***84 | Edge Group-Cutting | 1 |
| 28***01 | Bucket Ar-Grapple | 1 |
| 32***36 | Bucket Ar-Multipurpose, Protective Cover | 1 |
285-6112 Bucket Ar-Grapple
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
157-7225 Bucket Ar-Grapple -Industrial
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 15***25 | Bucket Ar-Grapple; -Industrial | 1 |
157-7223 Bucket Ar-Grapple
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***23 | Bucket Ar-Grapple | 1 |
| 16***36 | Cover Group-Lines | 1 |
158-6095 Bucket Ar-Grapple
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***95 | Bucket Ar-Grapple; -Industrial | 1 |
| 16***36 | Cover Group-Lines | 1 |
285-6111 Bucket Ar-Grapple
| 19***24 | Edge Group-Cutting | 1 |
| 28***11 | Bucket Ar-Grapple | 1 |
| 29***39 | Engine; - Assembly, Bucket Ar-Multipurpose | 1 |
157-7226 Bucket Ar-Grapple
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 15***26 | Bucket Ar-Grapple; -Industrial | 1 |
157-7227 Bucket Ar-Grapple
| 13***87 | Edge Group-Cutting | 1 |
| 15***27 | Bucket Ar-Grapple; -Industrial | 1 |
| 27***03 | Bucket Ar-Multipurpose | 1 |
157-7224 Bucket Ar-Grapple
| 13***86 | Edge Group-Cutting | 1 |
| 15***24 | Bucket Ar-Grapple | 1 |
| 27***98 | Bucket Ar-Multipurpose | 1 |
217-6229 Bucket Ar-Grapple
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 21***29 | Bucket Ar-Grapple | 1 |
217-6230 Bucket Ar-Grapple
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 21***30 | Bucket Ar-Grapple | 1 |
279-5420 Bucket Ar-Light Material
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5425 Bucket Ar-Light Material
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
279-5430 Bucket Ar-Light Material
| 13***85 | Edge Group-Cutting | 1 |
| 27***30 | Bucket Ar-Light Material | 1 |
| 32***46 | Bucket Ar-Multipurpose | 1 |
296-7597 Bucket Ar-Light Material
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7070 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***67 | Bucket As-General Purpose | 1 |
279-5380 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
325-7040 Bucket Ar-Multipurpose
| 14***35 | Edge | 1 |
| 32***40 | Bucket Ar-Multipurpose | 1 |
325-7076 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***71 | Bucket As-General Purpose | 1 |
279-5398 Bucket Ar-Multipurpose
| 13***85 | Edge Group-Cutting | 1 |
| 27***98 | Bucket Ar-Multipurpose | 1 |
| 28***99 | Bucket Group-Utility | 1 |
325-7065 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***63 | Bucket As-General Purpose | 1 |
279-5400 Bucket Ar-Multipurpose
| 14***36 | Edge | 1 |
| 27***00 | Bucket Ar-Multipurpose | 1 |
296-8057 Bucket Ar-Multipurpose
| 19***22 | Edge | 1 |
| 29***57 | Bucket Ar-Multipurpose | 1 |
154-5046 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 15***46 | Bucket Ar-Multipurpose | 1 |
325-7045 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***36 | Bucket As-Dirt | 1 |
293-0139 Bucket Ar-Multipurpose
| 14***37 | Edge | 1 |
| 29***39 | Engine; - Assembly, Bucket Ar-Multipurpose | 1 |
279-5402 Bucket Ar-Multipurpose
| 15***27 | Bucket As-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
325-7055 Bucket Ar-Multipurpose
| 14***37 | Edge | 1 |
| 32***55 | Bucket Ar-Multipurpose | 1 |
325-7036 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***33 | Bucket As-Dirt | 1 |
325-7056 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***88 | Bucket As-Dirt | 1 |
279-5390 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
279-5391 Bucket Ar-Multipurpose
| 19***24 | Edge Group-Cutting | 1 |
| 27***91 | Bucket Ar-Multipurpose | 1 |
| 32***76 | Bucket Ar-Multipurpose | 1 |
325-7046 Bucket Ar-Multipurpose
| 14***36 | Edge | 1 |
| 32***46 | Bucket Ar-Multipurpose | 1 |
154-5010 Bucket Ar-Multipurpose
| 13***86 | Edge Group-Cutting | 1 |
| 15***10 | Bucket Ar-Multipurpose | 1 |
| 32***56 | Bucket Ar-Multipurpose | 1 |
279-5392 Bucket Ar-Multipurpose
| 13***84 | Edge Group-Cutting | 1 |
| 27***92 | Bucket Ar-Multipurpose | 1 |
| 28***96 | Bucket Group-Utility | 1 |
325-7080 Bucket Ar-Multipurpose
| 19***22 | Edge | 1 |
| 32***80 | Bucket Ar-Multipurpose | 1 |
279-5401 Bucket Ar-Multipurpose
| 14***35 | Edge | 1 |
| 27***01 | Bucket Ar-Multipurpose | 1 |
279-5403 Bucket Ar-Multipurpose
| 14***04 | Bucket As-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
325-7060 Bucket Ar-Multipurpose
| 14***35 | Edge | 1 |
| 32***60 | Bucket Ar-Multipurpose | 1 |
325-7075 Bucket Ar-Multipurpose
| 14***37 | Edge | 1 |
| 32***75 | Bucket Ar-Multipurpose | 1 |
296-8055 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 18***16 | Bucket As-Dirt | 1 |
279-5381 Bucket Ar-Multipurpose
| 13***87 | Edge Group-Cutting | 1 |
| 27***81 | Bucket Ar-Multipurpose | 1 |
| 32***66 | Bucket Ar-Multipurpose | 1 |
279-5399 Bucket Ar-Multipurpose
| 13***86 | Edge Group-Cutting | 1 |
| 27***99 | Bucket Ar-Multipurpose | 1 |
| 28***02 | Bucket Group-Utility | 1 |
279-5382 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7066 Bucket Ar-Multipurpose
| 14***36 | Edge | 1 |
| 32***66 | Bucket Ar-Multipurpose | 1 |
325-7050 Bucket Ar-Multipurpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***39 | Bucket As-Dirt | 1 |
154-5004 Bucket Ar-Multipurpose
| 15***04 | Bucket Ar-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
325-7035 Bucket Ar-Multipurpose
| 14***34 | Edge | 1 |
| 32***35 | Bucket Ar-Multipurpose | 1 |
285-6101 Bucket Ar-Utility
| 22***32 | Edge | 1 |
| 28***01 | Bucket Ar-Utility | 1 |
285-6095 Bucket Ar-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***75 | Bucket As-General Purpose | 1 |
285-6100 Bucket Ar-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***00 | Bucket Ar-Utility | 1 |
165-6156 Bucket As-Dirt
| 14***37 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
| 16***56 | Bucket As-Dirt | 1 |
188-2716 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***88 | Bucket As-Grapple | 1 |
| 16***89 | Tack-Fastener | 4 |
268-4089 Bucket As-Dirt
| 16***30 | Plate-Identification; (Cat) | 2 |
| 19***22 | Edge | 1 |
| 26***89 | Bucket As-Dirt | 1 |
279-5439 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***23 | Bucket As-Light Material | 1 |
285-6088 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***28 | Bucket As-Light Material | 1 |
279-5436 Bucket As-Dirt
| 14***37 | Edge | 1 |
| 27***36 | Bucket As-Dirt | 1 |
141-6704 Bucket As-Dirt
| 14***04 | Bucket As-Dirt | 1 |
| 14***35 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
188-3526 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***89 | Bucket As-Grapple | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5437 Bucket As-Dirt
| 19***22 | Edge | 1 |
| 27***37 | Bucket As-Dirt | 1 |
285-6089 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***89 | Bucket As-Dirt | 1 |
279-5440 Bucket As-Dirt
| 22***82 | Edge | 1 |
| 27***40 | Bucket As-Dirt | 1 |
152-0227 Bucket As-Dirt
| 14***36 | Edge | 1 |
| 15***27 | Bucket As-Dirt | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
279-5434 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***22 | Bucket As-Light Material | 1 |
165-6157 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***87 | Bucket As-Grapple; -Industrial | 1 |
| 16***57 | Bucket As-Dirt | 1 |
279-5433 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 21***26 | Bucket As-Grapple | 1 |
279-5367 Bucket As-General Purpose
| 11***83 | Boss; (M10x1.5-Thd) | 4 |
| 14***36 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
292-9271 Bucket As-General Purpose
| 13***85 | Edge Group-Cutting | 1 |
| 16***57 | Bucket As-Dirt | 1 |
| 29***71 | Bucket As-General Purpose, Cap | 1 |
279-5375 Bucket As-General Purpose
| 14***36 | Edge | 1 |
| 27***75 | Bucket As-General Purpose | 1 |
279-5376 Bucket As-General Purpose
| 14***37 | Edge | 1 |
| 27***76 | Bucket As-General Purpose | 1 |
279-5372 Bucket As-General Purpose
| 14***35 | Edge | 1 |
| 27***72 | Bucket As-General Purpose | 1 |
279-5368 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***37 | Bucket As-Utility | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5363 Bucket As-General Purpose
| 27***63 | Bucket As-General Purpose | 1 |
| 29***57 | Edge | 1 |
292-9270 Bucket As-General Purpose -High Capacity
| 13***84 | Edge Group-Cutting | 1 |
| 16***56 | Bucket As-Dirt | 1 |
| 29***70 | Bucket As-General Purpose; -High Capacity | 1 |
279-5364 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***32 | Bucket As-Utility | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5371 Bucket As-General Purpose
| 14***35 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
| 27***71 | Bucket As-General Purpose | 1 |
156-0887 Bucket As-Grapple
| 13***86 | Edge Group-Cutting | 1 |
| 15***87 | Bucket As-Grapple; -Industrial | 1 |
| 18***26 | Bucket As-Dirt | 1 |
169-8943 Bucket As-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***43 | Bucket As-Grapple | 2 |
217-6227 Bucket As-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
156-0889 Bucket As-Grapple
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 15***89 | Bucket As-Grapple | 1 |
156-0888 Bucket As-Grapple
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***88 | Bucket As-Grapple | 1 |
| 16***89 | Tack-Fastener | 4 |
169-8941 Bucket As-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***41 | Bucket As-Grapple; -Industrial | 2 |
169-8942 Bucket As-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***42 | Bucket As-Grapple; -Industrial | 2 |
217-6226 Bucket As-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 21***26 | Bucket As-Grapple | 1 |
292-9223 Bucket As-Light Material
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 27***96 | Blade Group-Multipurpose Bucket | 1 |
292-9224 Bucket As-Light Material
| 15***12 | Pin | 2 |
| 19***08 | Clam As-Multipurpose Bucket | 1 |
| 27***05 | Blade Group-Multipurpose Bucket | 1 |
279-5428 Bucket As-Light Material
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***12 | Pin | 2 |
| 27***84 | Blade Group-Multipurpose Bucket | 1 |
279-5423 Bucket As-Light Material
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***12 | Pin | 2 |
| 15***45 | Blade Group-Multipurpose Bucket | 1 |
279-5429 Bucket As-Light Material
| 15***12 | Pin | 2 |
| 15***53 | Clam As-Multipurpose Bucket | 1 |
| 27***88 | Blade Group-Multipurpose Bucket | 1 |
279-5422 Bucket As-Light Material
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 27***22 | Bucket As-Light Material | 1 |
279-5424 Bucket As-Light Material
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 15***47 | Blade Group-Multipurpose Bucket | 1 |
279-5421 Bucket As-Light Material
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 27***21 | Bucket As-Light Material | 1 |
285-6103 Bucket As-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***97 | Bucket As-Utility | 1 |
285-6098 Bucket As-Utility
| 15***12 | Pin | 2 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 28***98 | Bucket As-Utility, Fuel Injection Pump; - Assembly | 1 |
165-8746 Bucket As-Utility
| 15***12 | Pin | 2 |
| 16***46 | Bucket As-Utility | 1 |
| 29***42 | Blade Group-Multipurpose Bucket | 1 |
285-6097 Bucket As-Utility
| 15***12 | Pin | 2 |
| 19***08 | Clam As-Multipurpose Bucket | 1 |
| 28***97 | Bucket As-Utility | 1 |
165-8837 Bucket As-Utility
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 16***37 | Bucket As-Utility | 1 |
165-8835 Bucket As-Utility
| 15***12 | Pin | 2 |
| 15***53 | Clam As-Multipurpose Bucket | 1 |
| 16***35 | Bucket As-Utility | 1 |
165-8832 Bucket As-Utility
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***12 | Pin | 2 |
| 16***32 | Bucket As-Utility | 1 |
152-0232 Bucket Gp-Dirt
| 15***32 | Bucket Group-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
152-0231 Bucket Gp-Dirt
| 15***31 | Bucket Group-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
268-4084 Bucket Gp-Dirt
| 19***42 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
| 26***84 | Bucket Group-Dirt | 1 |
188-2719 Bucket Gp-Dirt
| 18***19 | Bucket Group-Dirt | 1 |
| 19***43 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
296-8191 Bucket Gp-General Purpose
| 19***45 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
| 29***91 | Bucket Group-General Purpose | 1 |
156-0886 Bucket Gp-Grapple
| 15***86 | Bucket Group-Grapple; -Industrial | 1 |
| 19***42 | Fork Group-Pallet | 2 |
| 35***71 | Carriage Group-Fork | 1 |
156-0884 Bucket Gp-Grapple
| 15***84 | Bucket Group-Grapple; -Industrial | 1 |
| 35***71 | Carriage Group-Fork | 6 |
286-9244 Bucket Gp-Grapple
| 26***81 | Carriage Group-Fork | 6 |
| 28***44 | Bucket Group-Grapple | 1 |
217-6228 Bucket Gp-Grapple
| 19***45 | Fork Group-Pallet | 2 |
| 21***28 | Bucket Group-Grapple | 1 |
| 35***71 | Carriage Group-Fork | 1 |
286-9278 Bucket Gp-Grapple
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 25***95 | Step As | 1 |
156-0885 Bucket Gp-Grapple
| 15***85 | Bucket Group-Grapple; -Industrial | 1 |
| 19***43 | Fork Group-Pallet | 2 |
| 35***71 | Carriage Group-Fork | 1 |
279-5359 Bucket Gp-Grapple -Industrial
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 25***95 | Step As | 1 |
325-7077 Bucket Gp-Multipurpose
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
| 19***42 | Pin | 1 |
| 21***57 | Link Group-Coupler | 1 |
325-7037 Bucket Gp-Multipurpose
| 25***24 | Lines Group-Coupler | 1 |
| 25***01 | Coupler Group-Quick | 1 |
| 25***90 | Wiring Group-Quick Coupler | 1 |
279-5383 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 14***37 | Edge | 1 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
325-7047 Bucket Gp-Multipurpose
| 13***79 | Washer; (11x32x3-mm Thk) | 2 |
| 13***51 | Spacer; (11x19x6-mm Thk) | 2 |
| 15***97 | Spring | 2 |
154-5005 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 14***35 | Edge | 1 |
| 15***05 | Bucket Group-Multipurpose | 1 |
279-5397 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 16***30 | Plate-Identification; (Cat) | 2 |
| 22***32 | Edge | 1 |
293-0141 Bucket Gp-Multipurpose
| 25***00 | Coupler Group-Quick | 1 |
| 28***90 | Fitting Group-Hydraulic; -Manual | 1 |
| 29***41 | Bucket Group-Multipurpose | 1 |
325-7057 Bucket Gp-Multipurpose
| 20***85 | Pin | 2 |
| 21***62 | Cylinder & Link Group-Coupler; -Lh | 1 |
| 21***63 | Cylinder & Link Group-Coupler; -Rh | 1 |
279-5389 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 16***30 | Plate-Identification; (Cat) | 2 |
154-5009 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 14***36 | Edge | 1 |
| 15***09 | Bucket Group-Multipurpose | 1 |
279-5404 Bucket Gp-Multipurpose
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
325-7067 Bucket Gp-Multipurpose
| 16***28 | Plate | 1 |
| 32***67 | Bucket Group-Multipurpose | 1 |
| 5C***53 | Bolt (M6x1.00x16mm); (M6x1x16mm Thk) | 5 |
285-6102 Bucket Gp-Utility
| 14***88 | Edge-Cutting | 1 |
| 28***02 | Bucket Group-Utility | 1 |
| 3F***08 | Bolt-Plow; (5/8-11x2.25-In) | 13 |
285-6099 Bucket Gp-Utility
| 14***14 | Edge-Cutting | 1 |
| 28***99 | Bucket Group-Utility | 1 |
| 3F***08 | Bolt-Plow; (5/8-11x2.25-In) | 10 |
285-6096 Bucket Gp-Utility
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
| 19***42 | Pin | 1 |
| 21***57 | Link Group-Coupler | 1 |
353-1697 Carriage & Fork Ar
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
| 19***24 | Edge-Cutting | 1 |
| 35***97 | Carriage & Fork Ar | 1 |
293-9429 Carriage & Fork Ar
| 13***95 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
| 29***29 | Carriage & Fork Ar | 1 |
293-9428 Carriage & Fork Ar
| 13***94 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
| 29***28 | Carriage & Fork Ar | 1 |
353-1696 Carriage & Fork Ar
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 7 |
| 19***24 | Edge-Cutting | 1 |
| 35***96 | Carriage & Fork Ar | 1 |
353-1693 Carriage & Fork Ar
| 13***96 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
| 35***93 | Carriage & Fork Ar | 1 |
353-1694 Carriage & Fork Ar
| 13***97 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
| 35***94 | Carriage & Fork Ar | 1 |
293-9427 Carriage & Fork Ar
| 13***93 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 6 |
| 29***27 | Carriage & Fork Ar | 1 |
261-6681 Carriage Gp-Fork
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 13 |
| 26***81 | Carriage Group-Fork | 1 |
| 29***02 | Edge-Cutting | 1 |
351-9371 Carriage Gp-Fork
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***14 | Fork Group-Grapple; -Industrial | 2 |
| 27***75 | Cylinder Group-Grapple; -Industrial | 2 |
293-9426 Carriage Gp-Fork
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***14 | Fork Group-Grapple; -Industrial | 9 |
| 27***75 | Cylinder Group-Grapple; -Industrial | 2 |
154-5070 Clam As-Multipurpose Bucket
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 16***54 | Tine | 1 |
| 3E***70 | Pin; (Spring) | 1 |
154-5053 Clam As-Multipurpose Bucket
| 15***53 | Clam As-Multipurpose Bucket | 1 |
| 28***10 | Fork Group-Grapple | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
293-0148 Clam As-Multipurpose Bucket
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 9 |
| 29***48 | Clam As-Multipurpose Bucket | 1 |
199-8308 Clam As-Multipurpose Bucket
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
149-4232 Clam As-Multipurpose Bucket
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 28***05 | Fork Group-Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
296-0582 Conversion Gp-Work Tool -Kit, High Flow
| 22***29 | Positioner Group-Fork | 1 |
| 29***82 | Conversion Group-Work Tool; -Kit, High Flow | 1 |
258-2790 Coupler Ar-Quick
| 22***29 | Positioner Group-Fork | 1 |
| 25***90 | Coupler Ar-Quick | 1 |
258-2791 Coupler Ar-Quick
| 22***29 | Positioner Group-Fork | 1 |
| 25***91 | Coupler Ar-Quick | 1 |
258-2500 Coupler Gp-Quick
| 19***43 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
| 25***00 | Coupler Group-Quick | 1 |
258-2501 Coupler Gp-Quick
| 19***42 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
| 25***01 | Coupler Group-Quick | 1 |
162-5236 Cover Gp-Lines
| 16***36 | Cover Group-Lines | 1 |
| 19***45 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
215-3963 Cylinder & Link Gp-Coupler -Rh
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 7 |
| 16***38 | Fork Group-Utility | 1 |
215-3962 Cylinder & Link Gp-Coupler -Lh
| 16***41 | Tine | 1 |
| 21***62 | Cylinder & Link Group-Coupler; -Lh | 1 |
| 9R***59 | Clip | 1 |
222-7546 Edge Gp-Bit & Cutting
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***44 | Fork As; (Utility) | 1 |
222-7545 Edge Gp-Bit & Cutting
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 9 |
| 16***39 | Fork Group-Utility | 1 |
135-9385 Edge Gp-Cutting
| 13***85 | Edge Group-Cutting | 1 |
| 17***14 | Pin As | 1 |
| 17***55 | Shim; (1-mm Thk) | 1 |
135-9386 Edge Gp-Cutting
| 13***86 | Edge Group-Cutting | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
135-9384 Edge Gp-Cutting
| 13***84 | Edge Group-Cutting | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 7 |
135-9387 Edge Gp-Cutting
| 13***87 | Edge Group-Cutting | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
149-5741 Edge Gp-Cutting
| 14***41 | Edge Group-Cutting | 1 |
| 16***31 | Mounting Group-Cylinder; -Utility | 1 |
| 16***40 | Grapple Group-Utility | 1 |
135-9383 Edge Gp-Cutting
| 13***83 | Edge Group-Cutting | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
195-7124 Edge Gp-Cutting
| 15***11 | Pin | 4 |
| 15***35 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 16***43 | Arm As | 1 |
296-7680 Edge Gp-Cutting
| 19***37 | Plate | 1 |
| 19***45 | Spring | 1 |
| 19***54 | Pin-Spring | 2 |
285-6115 Fork Ar-Grapple -Utility
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 06***51 | Clamp | 4 |
| 10***59 | Spacer; (9x20x39.2-mm Thk) | 1 |
279-5360 Fork Ar-Grapple -Industrial
| 03***57 | Washer; (13x26x6-mm Thk) | 2 |
| 17***53 | Plate | 2 |
| 18***97 | Plate Group-Roading; -Lh | 1 |
285-6114 Fork Ar-Grapple -Utility
| 03***57 | Washer; (13x26x6-mm Thk) | 4 |
| 17***14 | Film-Stripe; (Reflective, Red, White) | 1 |
| 17***15 | Film; (Reflective)(Warning) | 1 |
279-5350 Fork Ar-Grapple -Industrial
| 19***37 | Plate | 1 |
| 19***45 | Spring | 1 |
| 19***54 | Pin-Spring | 2 |
279-5351 Fork Gp-Grapple -Industrial
| 19***45 | Spring | 1 |
| 27***51 | Fork Group-Grapple; -Industrial | 1 |
| 30***68 | Pin-Spring | 1 |
285-6110 Fork Gp-Grapple
| 17***47 | Pin | 1 |
| 28***10 | Fork Group-Grapple | 1 |
| 9R***01 | Pin-Cotter | 1 |
164-9614 Fork Gp-Grapple
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 06***51 | Clamp | 4 |
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 4 |
195-6943 Fork Gp-Pallet
| 16***60 | Pin-Spring | 1 |
| 19***42 | Pin | 1 |
| 19***43 | Fork Group-Pallet | 1 |
243-0002 Fork Gp-Pallet -Kit
| 17***41 | Spring | 4 |
| 17***73 | Plate As | 1 |
| 24***02 | Fork Group-Pallet; -Kit | 1 |
195-6942 Fork Gp-Pallet
| 16***60 | Pin-Spring | 1 |
| 19***42 | Pin | 1 |
| 19***42 | Fork Group-Pallet | 1 |
195-8545 Fork Gp-Pallet
| 17***14 | Film-Stripe; (Reflective, Red, White) | 1 |
| 17***15 | Film; (Reflective)(Warning) | 1 |
| 17***50 | Plate As; (Lh) | 1 |
243-0003 Fork Gp-Pallet -Kit
| 18***86 | Step As | 1 |
| 24***03 | Fork Group-Pallet; -Kit | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 2 |
243-0001 Fork Gp-Pallet -Kit
| 17***14 | Film-Stripe; (Reflective, Red, White) | 1 |
| 17***15 | Film; (Reflective)(Warning) | 1 |
| 17***51 | Plate As; (Rh) | 1 |
165-8736 Fork Gp-Utility
| 11***14 | Screen; (Water Tank) | 1 |
| 11***15 | Gasket | 1 |
| 16***36 | Fork Group-Utility | 1 |
165-8737 Fork Gp-Utility
| 16***37 | Fork Group-Utility | 1 |
| 19***06 | Cap As; (Water Tank) | 1 |
| 19***07 | Fitting-Drain | 1 |
165-8738 Fork Gp-Utility
| 16***38 | Fork Group-Utility | 1 |
| 25***27 | Screw-Truss Head; (No 12x17.46-mm) | 4 |
| 25***98 | Holder-Cup | 1 |
285-6105 Fork Gp-Utility
| 28***05 | Fork Group-Utility | 1 |
165-8732 Fork Gp-Utility
| 16***32 | Fork Group-Utility | 1 |
| 2S***08 | Washer-Retaining; (0.531x3.25x0.438-In Thk) | 2 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 1 |
165-8739 Fork Gp-Utility
| 16***39 | Fork Group-Utility | 1 |
230-5670 Frame Gp-Blade
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 20***45 | Strap-Cable | 2 |
| 23***70 | Frame Group-Blade | 1 |
279-5358 Frame Gp-Fork -Industrial
| 10***74 | Seal-Connector | 3 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
279-5352 Frame Gp-Fork -Industrial
| 25***68 | Compressor & Mtg Group-Refrig | 1 |
| 25***46 | Wiring Group-Heater | 1 |
| 25***52 | Duct & Filter Group-Cab Air | 1 |
285-6116 Grapple & Cylinder Gp-Utility
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***31 | Switch-Temperature; (Air Conditioner) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
165-8740 Grapple Gp-Utility
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 16***40 | Grapple Group-Utility | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
258-2536 Handle & Pin Gp-Coupler -Rh
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 25***36 | Handle & Pin Group-Coupler; -Rh | 1 |
258-2538 Handle & Pin Gp-Coupler -Lh
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 25***38 | Handle & Pin Group-Coupler; -Lh | 1 |
319-9480 Kit-Roading Plate & Mounting -Bucket
| 25***66 | Installation Group-Radio | 1 |
| 25***90 | Window Group-Cab; -Side | 1 |
| 25***29 | Accessory Group-Cab | 1 |
177-9152 Kit-Roading Plate & Mounting -Bucket
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 25***66 | Installation Group-Radio | 1 |
| 25***90 | Window Group-Cab; -Side | 1 |
258-3645 Kit-Water Tank & Mounting
| 25***45 | Kit-Water Tank & Mounting | 1 |
| 25***10 | Window Group-Cab | 1 |
| 25***20 | Liner Group-Cab | 1 |
346-1833 Kit-Water Tank & Mounting
| 27***74 | Cable Group-Control | 1 |
| 29***97 | Handle Group | 1 |
| 34***33 | Kit-Water Tank & Mounting | 1 |
215-3957 Link Gp-Coupler
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***93 | Lockwasher | 1 |
| 21***57 | Link Group-Coupler | 1 |
258-2535 Lock Gp-Quick Coupler -Rh
| 25***35 | Lock Group-Quick Coupler; -Rh | 1 |
| 26***29 | Shroud As | 1 |
| 28***41 | Coil As | 1 |
175-4238 Lock Gp-Quick Coupler -Mechanical
| 11***15 | Relay As; (12-Volt)(Junction Box) | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 25***84 | Bracket As; (Upper Lh) | 1 |
258-2537 Lock Gp-Quick Coupler -Lh
| 10***33 | Kit; (Receptacle) (Includes Receptacle As) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***16 | Terminal | 1 |
184-6097 Plate Gp-Roading -Lh
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 2 |
| 10***33 | Kit; (Receptacle) (Includes Receptacle As) | 1 |
| 10***95 | Terminal-Blade; (14-Ga To 18-Ga) | 2 |
184-6098 Plate Gp-Roading -Rh
| 18***98 | Plate Group-Roading; -Rh | 1 |
| 25***71 | Switch As; (Temperature Control) | 1 |
| 25***72 | Switch As; (Blower Fan Speed) | 1 |
177-1983 Spring Gp-Blade
| 17***83 | Spring Group-Blade | 1 |
| 26***66 | Control Group-Joystick; -Lh | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
188-7733 Step Gp-Material Handling Arm
| 18***33 | Step Group-Material Handling Arm | 1 |
| 26***65 | Control Group-Joystick; -Lh, High Flow | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
173-7407 Stop Gp-Bucket -Utility
| 17***07 | Stop Group-Bucket; -Utility | 1 |
| 26***64 | Control Group-Joystick; -Rh | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
116-2001 Strainer Gp-Water
| 11***01 | Strainer Group-Water | 1 |
| 26***62 | Control Group-Joystick; -Rh | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
166-2551 Tank Gp-Water
| 16***51 | Tank Group-Water | 1 |
| 26***63 | Control Group-Joystick; -Rh, High Flow | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
141-4999 Tooth Gp-Uni
| 14***99 | Tooth Group-Uni | 1 |
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 9 |
279C serial number reference
On this compact track loader the PIN plate is a riveted metal tag on the left side of the machine at the rear, under the left support/lift arm. As a "C"-model machine it also carries a stamped backup copy of the full PIN on the left side behind the front track roller. Read the first three characters as the letter prefix tied to the model and build series, and the digits that follow as the sequential unit number within that prefix (for example MBT, then a sequence starting near 00001-UP).
| Prefix | Identifies | Notes |
|---|---|---|
| MBT | 279C Multi Terrain Loader / Compact Track Loader, standard-flow and high-flow (XPS) hydraulics | Only documented serial prefix for the 279C, covering MBT00001 and up. Fitted with the Cat C3.4 DIT turbocharged four-cylinder diesel (also referenced under its earlier industrial engine designation 3044C), rated about 63 kW (84 hp) gross, 61 kW (82 hp) net. Standard-flow and optional high-flow XPS hydraulics are both built under this same prefix, not a separate one. Two-speed hydrostatic travel drive on steel-embedded rubber tracks, with a fully suspended torsion-axle undercarriage. Production runs roughly the late 2000s into 2012; used-unit listings run later into the mid-2010s, so treat the tail end of the range as soft. Superseded by the 279C2 (Series 2), which carries its own separate KWB prefix and is a distinct model listing, not part of this family. |
Frequently asked questions
What engine does the Cat 279C use?
A Cat C3.4 DIT (3044C) four-cylinder turbocharged diesel. The base 279C is rated 84 hp gross / 82 hp net (Tier 3 / Stage IIIA). The 279C Series 2 keeps the same engine block, retuned to 74 hp gross / 73 hp net for Tier 4 Interim / Stage IIIB.
What is the operating weight of the Cat 279C?
About 4,475 to 4,487 kg (9,866 to 9,892 lb), depending on series and configuration such as standard-flow versus high-flow hydraulics and cab type. Treat exact figures as varying by configuration/series rather than a single fixed number.
What replaced the Cat 279C?
The 279C Series 2 (279C2) replaced the base 279C on the same chassis and engine block, retuned for a later emissions step. The 279C2 was in turn replaced by the 279D, which switched to a different, smaller-displacement Cat C3.3B DIT engine at Tier 4 Final.
What 279C owners discuss
What is the most reported drivetrain complaint on the Cat 279C, and what does it usually mean?
Owners describe the loader tracking normally, then losing travel speed going up a rise or after a load spike, with speed not returning even once engine revs are back to normal. Only a full stop and restart brings it back. This pattern has been reported across more than one production year and points to the hydrostatic drive circuit, not the engine itself. A more serious version is losing drive, hydraulic implement function, and cooling fan speed all at once. That combination usually means the coupling between the engine and the hydrostatic pump has slipped or failed, not an electrical fault. Check coupling condition before condemning a pump or motor.
What undercarriage wear pattern should owners watch for on this loader?
This loader rides on steel-embedded rubber tracks with a torsion-axle suspension that needs daily grease at the axle pivots. Track tension gets checked on a set interval, commonly cited around every 100 hours, with sag set to roughly 12 mm (0.5 in) measured with a straightedge from the drive sprocket to the idler. Tracks run looser than spec let the drive lugs jump the sprocket teeth, called ratcheting, which chews up both the lugs and the sprocket fast. Track pads worn down near minimum thickness are a normal wear item to budget for, not a defect. Varies by track brand and ground conditions.
Are there known engine quirks on the C3.4 DIT that owners get misdiagnosed?
Community reports on this loader describe the engine bogging down and sputtering under load in drive, as if air had gotten into the fuel, sometimes recovering briefly after a restart before losing power again. The C3.4 engine family used in this generation of loaders also carries a well-known misdiagnosis trap: a rough-running or misfiring engine under load gets blamed on the turbocharger, when injector condition, valve clearance, or a suction-side fuel air leak turn out to be the actual cause. Check fuel delivery and valve lash before replacing a turbo.
Why would a 279C start fine cold but refuse to restart once it is hot?
This is a recurring complaint on this model. An engine that fires right up cold but will not restart after running to full operating temperature and being shut off usually traces to a heat-soaked fuel shutoff solenoid or injection-side components vapor-locking once hot, rather than a dead battery or starter. Check the solenoid wiring, its connector, and fuel filter condition first. Letting the engine cool for several minutes before trying again is a field workaround, not a permanent fix.
What electrical or sensor issues come up most for the 279C's controls?
Loss of function on one joystick, bucket lift, tilt, or drive response, shows up regularly in owner reports. Two separate causes get reported: a low-voltage condition in the fusebox that starves the joystick circuit (check the relevant fuse and connector grounds first), and a faulty door or seat safety-interlock switch that opens the pilot circuit and kills hydraulics. The joystick's own position sensors are sealed Hall-effect modules that are not separately serviceable, so a bad sensor means replacing the whole joystick assembly. Because these interlocks are safety devices, have your dealer verify wiring and switch function rather than bypassing them.
The high-flow circuit behaves oddly on some machines. Is that normal or a fault?
Needing the lift arms raised before the auxiliary high-flow or continuous-flow circuit will engage is normal design behavior on this loader, not a fault. What is a genuine, reported problem is needing to raise the arms progressively higher over time before high-flow will engage, or losing bucket lift and curl power after working near relief pressure. Both patterns point to a clogging screen inside the main hydraulic control valve or a relief valve going out of adjustment or failing, not a wiring issue.
What should a buyer check before purchasing a used Cat 279C?
Confirm the engine starts and holds a clean idle and RPM both cold and after a full warm-up cycle, since hot-restart hesitation is a known weak point on this model. Ask for service records on the fuel injection pump and injectors, since some units in the field needed the injection pump replaced more than once by mid-life. Check track sag against spec and look at lug wear, and confirm the torsion-axle grease points have been serviced regularly. Cycle every joystick function repeatedly, including auxiliary and high-flow, watching for intermittent dropout. Verify drive, hydraulics, and the cooling fan all respond correctly together to throttle changes, since simultaneous weakness across all three points to a worn engine-to-pump coupling. Confirm the seat and door safety switches actually cut hydraulics and drive when tripped. Have your dealer run a full diagnostic and code check as final confirmation before you buy.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 279C part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.