Caterpillarskid steer loader
Caterpillar 268B
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 268B is a wheeled, chain-drive skid steer loader and the largest wheeled model in Cat's early-2000s B-series compact loader lineup, built roughly 2004 to 2009 under the LBA PIN prefix. It runs a Cat 3044C DIT, a turbocharged four-cylinder diesel of about 3.3 L (201 cu in), rated near 57 kW (76-77 hp) net flywheel power and about 61 kW (82 hp) gross, figures that shift slightly depending on the rating standard a given source cites. Operating weight is about 3,626 kg (7,995 lb), with a rated operating capacity near 1,225 kg (2,700 lb) and tipping load around 2,545 kg (5,615 lb). Standard configuration is an open, tilt-up ROPS/FOPS canopy with removable side windows; an enclosed heated or air-conditioned cab is a factory option, as is a two-speed drivetrain (raising travel speed from about 11.6 km/h / 7.2 mph to 17.7 km/h / 11 mph) and Cat's High Flow XPS hydraulic circuit for flow-hungry attachments like mulchers and cold planers.
Cat's B-series updated its original numbered wheeled skid steers, launched from 1999, with turbocharged DIT engines, load-sensing hydraulics, and a revised cab across the range from the 216B up through the 262B; the 268B carried no plain-numbered forerunner of its own, effectively extending the lineup above the 262/262B as the largest chain-drive wheeled loader Cat built in that generation. Around 2009 Caterpillar shifted its wheeled skid steer offering to the C-series, with updated engines and tighter emissions compliance; there's no confirmed single 268C successor, so treat the transition as a lineup change rather than a direct model swap. The 268B is long out of production and now shows up mainly in resale and rental fleets. Its chain-drive undercarriage, mechanically injected engine, and separate hydraulic and chain-case fluid circuits make it straightforward to service, but the interlock safety circuit is a well-known point of confusion on used units, and buyers should confirm PIN-to-engine match and interlock wiring integrity before purchase.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 268B specifications
Engine
| Engine model | Cat 3044C DIT, 4-cylinder inline diesel, turbocharged, water-cooled |
| Displacement | 3.3 L (201.2 cu in) |
| Bore x stroke | 94 mm x 120 mm (3.7 in x 4.7 in) |
| Gross power (SAE J1995) | 61 kW (82 hp) |
| Net flywheel power | 56.7-57 kW (76-76.5 hp) |
| Emissions tier | U.S. EPA Tier 2 |
Weights
| Operating weight, standard configuration | 3626 kg (7995 lb) |
| Shipping weight | 3300 kg (7260 lb) — single-source figure, verify against dealer data for the specific unit |
Dimensions
| Overall length with bucket | 3610-3630 mm (11.87-11.9 ft) |
| Length without bucket | 2900-2930 mm (9.53-9.6 ft) |
| Width over tires | 1829-1860 mm (72-73.2 in) |
| Height to top of cab (ROPS), transport position | 2063-2110 mm (81.2-83 in) — varies by source |
| Maximum overall height, lift arms raised | 4064 mm (160 in) |
| Wheelbase | 1220-1250 mm (48-49.2 in) |
| Ground clearance | 195-203 mm (7.7-8 in) |
| Turning radius from center, rear | 1702 mm (67 in) |
Performance
| Travel speed, standard single-speed | 11.6-11.75 km/h (7.2-7.3 mph), forward and reverse |
| Travel speed, two-speed option | 17.7-17.8 km/h (11-11.1 mph) |
| Rated operating capacity (50% of tipping load) | 1225 kg (2700 lb) |
| Tipping load, straight | 2545-2546 kg (5613-5615 lb) |
| Bucket breakout force (tilt) | 2498 kg (5508 lb) |
| Lift-arm breakout force | 2355 kg (5192-5193 lb) |
| Maximum lift height (hinge pin) | 3.23 m (10.6 ft / approx. 127 in) |
| Hydraulic pump flow / system pressure | 125 L/min (33 gal/min) at up to 280 bar (4060 psi), load-sensing, pressure-compensated variable-displacement pump |
| Gradeability | not published in available sources |
Service capacities (summary)
| Fuel tank | 90 L (23.7-23.8 gal) |
| Hydraulic system, total (reservoir plus lines/components) | 53 L (14 gal); reservoir alone approx. 35 L (9.2 gal) |
| Engine oil, refill with filter change | 10 L (2.6-2.7 gal); SAE 10W-30 or 15W-40, API CE/CF-4/CG-4/CH-4 |
| Cooling system | 10-10.5 L (2.6-2.75 gal); Cat diesel engine antifreeze/coolant |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
268B fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 9.8–10.2 L (2.6–2.7 US gal) | Cat DEO SAE 10W-30 or 15W-40, API CF-4/CG-4/CH-4 service category. Use 10W-30 for cold starts near or below 0°C (32°F); 15W-40 in warmer climates. |
| Cooling system | 9.8–10.5 L (2.6–2.75 US gal) | Cat DEAC (Diesel Engine Antifreeze/Coolant), premixed or 50/50 concentrate-to-water. Protects to about -37°C (-34°F). Cat ELC extended-life coolant is an approved alternative fill. |
| Fuel tank | 90.0 L (23.7 US gal) | Diesel fuel meeting Cat's No. 2-D specification. No. 1-D blend recommended for cold-weather starting. |
| Hydraulic tank (reservoir) | 35.0 L (9.2 US gal) | Cat TDTO or Cat HYDO, SAE10W, meeting Cat TO-4 spec. Same reservoir and fluid also feed the hydrostatic drive system. |
| Hydraulic system total (reservoir, lines, cylinders) | 53.0 L (14.0 US gal) | Same fluid as reservoir fill: Cat TDTO or Cat HYDO, SAE10W, Cat TO-4 spec. |
| Chain case final drive, each side | 8.0 L (2.1 US gal) per side | Cat TDTO SAE30, Cat TO-4 spec. SAE10W-30 TO-4 oil accepted as a cold-climate substitute. |
| Grease (all points) | Per lubrication chart — no reservoir capacity | Cat Multipurpose Grease (Cat MPGM), NLGI 2. Cat Advanced 3Moly Grease approved for extended-interval service. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 268B maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 6,000 h |
|
| Every 8,000 h |
|
Servicing the 268B beyond the schedule
Predictive Maintenance & Fluid Analysis
Sample engine oil every service interval on the mechanically injected 3044C DIT; injector nozzle wear and pump-timing drift often show up in oil trends before they show up as a hard-start complaint. The hydraulic reservoir and both side chain cases run separate Cat TO-4 fluids (SAE10W hydraulic, SAE30 chain case); sample and trend each independently, not as one system. Watch for the hydraulic filter bypass indicator between changes; a lit lamp means contamination is already restricting flow. Track coolant condition alongside oil.
Corrective & Common Repairs
The most repeated 268B complaint is a machine that cranks and runs but won't drive or lift: check the seat/lap-bar switch, park-brake sensor, and interlock module connector before suspecting the ECM. A bucket that creeps down with no visible leak, especially after a wash, points to moisture-stuck pilot solenoids or worn tilt-cylinder seals, not a failing pump. Pulling hard to one side at brake release signals uneven hydrostatic charge pressure or a weak drive motor. Turbo oil weeping traces to a blocked drain line or aging seals, not turbo failure.
Overhaul & Rebuild Points
At major overhaul, open both side chain cases together, since wear rarely stays even side to side on the 268B's chain-drive undercarriage. Reseal the hydrostatic pump and drive motors and rebalance charge pressure side to side rather than swapping one component alone. On the mechanically injected 3044C DIT, check injection pump timing, turbocharger shaft play, and valve lash before hours push the engine toward bottom-end wear. Reseal tilt and lift cylinders showing drift, and inspect the ROPS/FOPS canopy or cab structure and interlock wiring harness before return to service.
Seasonal & Environment Servicing
Switch to Cat DEO 10W-30 engine oil below 0°C (32°F) and blend in No. 1-D fuel for reliable cold starts; the chain cases accept a SAE10W-30 TO-4 substitute for the standard SAE30 fill in cold climates. In hot, dusty operation, clean the radiator and oil cooler core more often, since the turbocharged 3044C DIT and the closed hydrostatic circuit both run hotter under packed debris. After a wash or heavy rain, cycle lift and tilt before working under a raised attachment; moisture is a known cause of sticking pilot solenoids.
268B common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 110-6326 | Filter Element As-Air | Air intake service | Check fitment → |
| 110-6331 | Filter Element As-Air | Air intake service | Check fitment → |
| 1G-8878 | Filter As-Oil | Hydraulic service | Check fitment → |
| 1R-0734 | Filter-Engine Oil | Lubrication service | Check fitment → |
| 134-0404 | Switch As-Pressure | Lubrication service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
268B fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| Engine oil pressure lamp (red) | Engine oil pressure has dropped below the safe minimum; this is a Level 3 alert - flashing with an audible alarm. | Low engine oil level, failed oil pump, plugged pickup screen, or a faulty pressure sender/switch. | Stop the machine and shut the engine down immediately. Check oil level and look for leaks before attempting a restart. |
| Electronic control / interlock fault lamp (amber, exclamation symbol) | A fault is logged in the interlock control circuit that governs the seat, seat bar (lap bar), and park brake safety interlocks - engine runs but hydraulics and drive stay locked out. | Corroded connector at the interlock control module (mounted under the operator's floor, left side), a faulty seat or lap-bar switch, or damaged interlock wiring. | Inspect and clean the seat/lap-bar switch wiring and the interlock module connector first. If the lamp stays on, connect Cat ET to pull the stored fault before replacing parts. |
| Amber alert lamp, flashing with audible alarm (Level 3) | Critical warning; continued operation risks operator injury or serious component damage. | Varies by which gauge or system triggered it - commonly tied to engine oil pressure or coolant overtemperature on this machine class. | Stop the machine immediately, shut off the engine, and identify the triggering gauge or system before resuming work. |
| Amber alert lamp, flashing without alarm (Level 2) | Elevated warning; component damage is possible if the operating condition continues unchanged. | A monitored value (commonly hydraulic oil temperature) is approaching its upper limit. | Change how the machine is being operated, reduce load, and let the system cool before continuing. |
| Coolant temperature gauge/lamp in red zone | Engine coolant temperature above normal operating range. | Low coolant level, plugged radiator fins, slipping or broken fan belt, or a failed thermostat. | Idle down, let the engine cool, then check coolant level and radiator for debris before resuming work. |
| Hydraulic oil temperature indicator (amber thermometer symbol) | Signals hydraulic fluid is outside normal operating temperature - lit during cold-start warm-up, or if fluid runs too hot under sustained heavy load. | On startup, this is normal until the fluid warms up. If it lights during operation, suspect low fluid level, a plugged cooler, or extended high-load work. | On cold start, allow normal warm-up. During operation, stop and check fluid level and cooler condition if the lamp stays lit. |
| Hydraulic filter bypass indicator | Hydraulic return filter is restricted enough that oil is bypassing the filter element. | Filter due for a change, or contamination has built up in the hydraulic system. | Replace the hydraulic filter at the next service interval and inspect for a contamination source if it recurs quickly. |
| Low alternator charge / battery lamp | Charging system output is below specification. | Worn or broken alternator belt, failing alternator, or loose/corroded battery connections. | Check belt tension and battery terminals first, then test alternator output and replace as needed. |
| Parking brake engaged lamp | Park brake circuit is engaged, which blocks drive function even with the engine running. | Brake switch left engaged, low pilot/release pressure, or a faulty brake-release solenoid - a frequent source of "won't drive" complaints on this machine. | Confirm the brake release switch position and pressure, then check the release solenoid and wiring if the brake will not disengage. |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
268B attachments & work tools
Buckets
Cat offered a full bucket lineup sized to the 268B's roughly 1.7 m (66 in) standard width and about 1225 kg (2700 lb) rated operating capacity: general-purpose/dirt, utility, light-material (snow, grain, fertilizer), low-profile, and skeleton (rock/debris) buckets. Widths across the range span roughly 1.4-2.3 m (56-92 in) and capacities roughly 0.3-0.7 m3 depending on bucket type.
Grapples
Industrial and utility grapple buckets add a hydraulically clamped top jaw to the standard bucket shell for brush, debris, and irregular material handling. Sized to the same 1.6-2.0 m (62-80 in) width class as the bucket lineup and run off the machine's auxiliary hydraulic circuit.
Forks
Pallet forks and construction forks are offered for palletized material handling, rated within the machine's roughly 1225 kg (2700 lb) operating capacity (payload derates with load center and any counterweight fitted). Log/lumber forks and industrial grapple forks are also offered for round stock and land-clearing debris.
Ground-engaging tools (augers, trenchers)
Augers for post holes, footings, and tree planting, and trenchers for narrow utility/drainage trenches, are offered in sizes matched to this mid-frame skid steer class and run on the standard auxiliary circuit. A backhoe attachment is not confirmed for this model - period Cat backhoe compatibility charts for skid steers begin with later-generation loaders, not the 268B.
Cold planer / milling
A skid-steer cold planer for small asphalt and concrete milling jobs is offered in this size class. Given its power draw, it is best matched to the High Flow XPS hydraulic configuration rather than the base standard-flow machine.
Mulchers, stump grinders, wheel saws, tillers
High-draw vegetation and cutting tools - forestry mulcher, stump grinder, wheel saw, landscape tiller - are offered for this size class of loader but need the optional high-flow hydraulic circuit to work effectively; on a standard-flow 268B these tools are underpowered.
Blades and brooms
Angle dozer blades for grading and snow pushing, plus angle and utility (pickup) brooms for surface cleanup, are offered for this class and run on standard auxiliary flow.
Snow blower
A rotary snow blower attachment is offered for winter clearing on machines this size. Larger units benefit from the high-flow circuit while smaller units run adequately on standard flow.
Hydraulic kit / flow arrangement
The 268B was built as a standard-flow machine and also offered as a factory High Flow XPS variant. Both use a load-sensing, variable-displacement pump; period spec sheets list flow up to about 125 L/min (33 gal/min) at high idle and system relief around 280 bar (4060 psi), figures that vary slightly by source and should be treated as approximate. The XPS closed-center arrangement is tuned to deliver more usable power to flow-hungry tools (cold planer, mulcher, trencher, stump grinder) across the engine speed range; lighter tools such as buckets, forks, augers, and brooms run fine on the base standard-flow setup.
Coupler / mounting system
Work tools mount on Cat's own hydraulically-released quick-coupler frame at the loader arm, using the common skid-steer quick-attach wedge/pin geometry so tools can be changed without leaving the seat. Auxiliary hydraulic lines connect through flat-face quick-disconnect couplings mounted on the arm, sized to whichever aux circuit (standard or high-flow) the machine carries.
Rated capacity / counterweight
Base rated operating capacity is about 1225 kg (2700 lb) at 50% of tip load, with tipping load around 2545 kg (5615 lb); exact figures vary slightly by source. A rear counterweight kit is offered as a dealer-fit option to add ballast and raise ROC when running nose-heavy attachments like grapples or forks; the exact capacity gain varies by configuration.
Cab / operator guarding
Standard configuration is an open, tilt-up ROPS canopy with FOPS Level I overhead guard, with removable/sliding side windows. An enclosed cab with heater and/or air conditioner is a factory option. Extra window or screen guarding for brush, forestry, or demolition work is not documented for this exact model - verify with your dealer if needed.
All 268B assemblies by section
Every catalogued assembly group for the Caterpillar 268B. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
243-0405 Air Cleaner Gp
| 11***26 | Filter Element As-Air; (Primary) | 1 |
| 11***31 | Filter Element As-Air; (Secondary) | 1 |
| 11***17 | Valve-Dust; (Air Cleaner) | 1 |
222-9812 Air Cleaner Gp
| 22***12 | Air Cleaner Group | 1 |
| 24***05 | Air Cleaner Group | 1 |
| 5C***61 | Nut (M8x1.25 Thd); (M8x1.25 Thd) | 2 |
247-6317 Lines Gp-Air
| 24***17 | Lines Group-Air | 1 |
| 5I***78 | Gasket | 1 |
| 5I***21 | Elbow Assem. | 1 |
218-0945 Lines Gp-Air
| 21***57 | Clamp | 1 |
| 21***45 | Lines Group-Air | 1 |
| 22***18 | Hose As | 1 |
235-5893 Manifold Gp-Exhaust
| 23***60 | Bolt | 8 |
| 23***23 | Manifold | 1 |
| 23***24 | Gasket-Manifold | 1 |
287-5323 Manifold Gp-Exhaust
| 19***60 | Nut; (M8x1.25-Thd) | 8 |
| 23***60 | Bolt | 8 |
| 23***24 | Gasket-Manifold | 1 |
287-4832 Manifold Gp-Inlet
| 09***49 | Bolt; (M8x1.25x40-mm) | 12 |
| 23***05 | Manifold-Inlet | 1 |
| 23***06 | Gasket; (Inlet Manifold) | 1 |
235-5892 Manifold Gp-Inlet
| 23***05 | Manifold-Inlet | 1 |
| 23***06 | Gasket; (Inlet Manifold) | 1 |
| 23***92 | Manifold Group-Inlet | 1 |
261-8044 Muffler & Converter
| 26***44 | Muffler & Converter | 1 |
258-2462 Muffler & Mounting Gp
| 19***76 | Washer-Hard; (8.8x20x8-mm Thk) | 3 |
| 23***21 | Nut; (M10x1.25-Thd) | 1 |
| 25***19 | Muffler As | 1 |
222-9815 Muffler & Mounting Gp
| 19***76 | Washer-Hard; (8.8x20x8-mm Thk) | 3 |
| 22***15 | Muffler & Mounting Group | 1 |
| 22***16 | Muffler As; (Standard) | 1 |
272-3051 Muffler Gp
| 19***76 | Washer-Hard; (8.8x20x8-mm Thk) | 3 |
| 23***21 | Nut; (M10x1.25-Thd) | 1 |
| 27***50 | Muffler As | 1 |
235-5894 Turbocharger Gp
| 09***00 | Washer; (1.5mm Thk) | 3 |
| 19***06 | Gasket | 4 |
| 23***18 | Gasket | 1 |
Basic Engine
292-4041 Bearing Gp-Main
| 10***88 | Plate-Thrust; (Standard) | 3 |
| 10***89 | Plate-Thrust; (0.15-mm Os) | 0 |
| 10***90 | Plate-Thrust; (0.35-mm Os) | 0 |
233-5473 Camshaft Gp
| 09***28 | Key | 1 |
| 10***72 | Tappet | 8 |
| 10***73 | Rod-Push | 8 |
287-4033 Connecting Rod Gp
| 10***80 | Rod As-Connecting | 4 |
| 12***55 | Bolt-Connecting Rod | 2 |
| 12***56 | Nut | 2 |
233-5480 Cover Gp-Valve Mechanism
| 23***80 | Cover Group-Valve Mechanism | 1 |
| 23***83 | Gasket; (Valve Cover) | 1 |
| 31***98 | Cap-Oil Filler; (Engine) | 1 |
234-4793 Crankshaft Gp
| 08***13 | Pin | 2 |
| 09***28 | Key | 2 |
| 13***96 | Nut | 1 |
287-4649 Crankshaft Gp
| 08***13 | Pin | 2 |
| 09***28 | Key | 2 |
| 13***96 | Nut | 1 |
235-5883 Cylinder Block Gp
| 09***41 | Cap | 6 |
| 09***20 | Pin | 2 |
| 10***62 | Bushing | 1 |
287-2416 Cylinder Block Gp
| 09***41 | Cap | 4 |
| 09***20 | Pin | 2 |
| 10***62 | Bushing | 1 |
233-5500 Cylinder Head Gp
| 21***75 | Cap | 7 |
| 23***53 | Cylinder Head | 1 |
| 23***54 | Bolt; (M12x1.75x115-mm) | 17 |
218-4836 Drain Gp-Engine Oil
| 11***70 | Cap | 1 |
| 1P***78 | Clamp; (Hose) | 1 |
| 21***19 | Adapter | 1 |
235-5890 Flywheel Gp
| 03***39 | Gear-Starter; (112-Teeth) | 1 |
| 22***93 | Bolt; (M12x1.25x30-mm) | 4 |
| 23***91 | Flywheel As | 1 |
235-5891 Gear Gp-Front
| 11***27 | Gear; (46-Teeth) | 1 |
| 11***83 | Gear As-Idler; (49-Teeth) | 1 |
| 11***85 | Gear-Pump; (Oil, 31-Teeth) | 1 |
287-4830 Gear Gp-Front
| 11***27 | Gear; (46-Teeth) | 1 |
| 11***29 | Gear; (23-Teeth) | 1 |
| 11***83 | Gear As-Idler; (49-Teeth) | 1 |
280-8297 Guard Gp-Belt
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 3 |
| 21***21 | Guard-Belt | 1 |
| 22***87 | Bracket As | 1 |
218-0940 Guard Gp-Belt
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 3 |
| 13***22 | Bolt-Locking; (M8x1.25x16-mm) | 2 |
| 21***21 | Guard-Belt | 1 |
287-3357 Housing Gp-Flywheel
| 09***15 | Lockwasher | 2 |
| 10***80 | Gasket-Rear | 1 |
| 11***15 | Seal As-Oil | 1 |
235-5886 Housing Gp-Flywheel
| 10***80 | Gasket-Rear | 1 |
| 11***15 | Seal As-Oil | 1 |
| 14***17 | Bolt; (M10x1.25x25-mm) | 10 |
287-3074 Housing Gp-Front
| 09***29 | Seal-O-Ring (Id=139.5mm); (Id=139.50mm) | 1 |
| 10***77 | Gasket-Front Plate | 1 |
| 11***47 | Gasket; (Gear Case) | 1 |
287-1844 Lifting Gp-Engine
| 19***05 | Bolt As | 4 |
| 23***66 | Eye | 1 |
| 23***68 | Gasket; (Rear Head) | 1 |
238-8276 Lifting Gp-Engine
| 23***66 | Eye | 1 |
| 23***82 | Eye | 1 |
| 23***76 | Lifting Group-Engine | 1 |
218-0923 Mounting Gp-Engine
| 12***80 | Locknut; (M12x1.75-Thd) | 1 |
| 16***95 | Washer; (16.5x71.5x3-mm Thk) | 4 |
| 21***17 | Bracket As | 1 |
287-3921 Pan Gp-Oil
| 16***01 | Sealant-Silicone | 0 |
| 19***03 | Bolt As | 1 |
| 23***11 | Washer | 1 |
300-9450 Pan Gp-Oil
| 09***82 | Gasket, Oil Drain | 1 |
| 13***32 | Plug; (Drain, Engine Oil) | 1 |
| 19***03 | Bolt As | 1 |
235-5889 Piston Gp
| 22***04 | Set-Piston Ring; (Standard) | 4 |
| 23***14 | Piston; (Standard) | 4 |
| 23***15 | Pin-Piston | 4 |
287-2983 Plug Gp-Engine
| 19***11 | Plug | 1 |
| 28***83 | Plug Group-Engine; -Cylinder Block, Rh | 1 |
287-2922 Plug Gp-Engine
| 28***22 | Plug Group-Engine; -Cylinder Block, Lh | 1 |
| 5I***05 | Plug | 6 |
241-6015 Pulley Gp-Crankshaft
| 23***86 | Pulley-Crankshaft | 1 |
| 24***15 | Pulley Group-Crankshaft | 1 |
287-6114 Pulley Gp-Water Pump
| 23***07 | Pulley | 1 |
| 28***14 | Pulley Group-Water Pump | 1 |
| 8T***42 | Bolt; (M8x1.25x14-mm) | 4 |
239-0686 Pulley Gp-Water Pump
| 23***07 | Pulley | 1 |
| 23***72 | V-Belt; (Water Pump) | 1 |
| 23***86 | Pulley Group-Water Pump | 1 |
287-6138 V-Belt Gp
| 23***72 | V-Belt; (Water Pump) | 1 |
| 28***38 | V-Belt Group; -Water Pump | 1 |
235-5880 Valve Mechanism Gp
| 09***05 | Cap | 1 |
| 19***24 | Ring-Snap | 2 |
| 22***45 | Rocker As | 8 |
Cooling System
235-5896 Cooler Gp-Engine Oil
| 09***13 | Seal-O-Ring | 4 |
| 09***21 | Plug | 2 |
| 23***98 | Stud | 1 |
292-4040 Drain Gp-Coolant
| 23***78 | Valve As-Drain | 1 |
| 29***40 | Drain Group-Coolant | 1 |
235-5900 Lines Gp-Water
| 09***75 | Bolt; (25-mm Long) | 2 |
| 23***31 | Cover | 1 |
| 23***59 | Gasket; (Water Temperature Regulator) | 1 |
218-0938 Mounting Gp-Rad & Oil Cooler
| 14***32 | Pin As | 1 |
| 17***55 | Pin | 2 |
| 19***45 | Spring-Gas; (Grill) | 1 |
235-5899 Pump Gp-Water
| 10***47 | Cover-Pump | 1 |
| 10***50 | Gasket-Cover; (Water Pump) | 1 |
| 23***32 | Flange | 1 |
287-6056 Pump Gp-Water
| 28***66 | Bolt; (M8x1.25x65-mm) | 1 |
| 28***56 | Pump Group-Water | 1 |
| 33***17 | Pump Group-Water | 1 |
335-9117 Pump Gp-Water
| 10***47 | Cover-Pump | 1 |
| 19***60 | Plug | 1 |
| 33***17 | Pump Group-Water | 1 |
261-6219 Radiator & Hyd Oil Cooler Gp
| 03***65 | Cap As-Radiator; (Sea Water Heat Exchanger) | 1 |
| 06***80 | Fitting | 1 |
| 20***27 | Fan As | 1 |
221-9124 Radiator & Hyd Oil Cooler Gp
| 03***65 | Cap As-Radiator; (Sea Water Heat Exchanger) | 1 |
| 06***80 | Fitting | 1 |
| 20***27 | Fan As | 1 |
218-0924 Radiator & Oil Cooler Mtg Gp
| 13***40 | Locknut; (M8x1.25-Thd) | 2 |
| 16***15 | Cap-Vented; (Coolant Recovery Tank) | 1 |
| 1P***78 | Clamp; (Hose) | 2 |
261-6218 Radiator & Oil Cooler Mtg Gp
| 10***86 | Sleeve | 1 |
| 16***15 | Cap-Vented; (Coolant Recovery Tank) | 1 |
| 1P***78 | Clamp; (Hose) | 2 |
Electrical And Starting System
3e-7584 Lamp Gp-Head & Signal
| 10***46 | Lamp; (12-Volt, 4-Watt)(Miniature) | 1 |
| 10***47 | Body As-Lamp | 1 |
| 10***48 | Lens As; (Headlight)(High, Low Beam) | 1 |
105-2814 Alternator Gp-Charging
| 10***14 | Alternator Group-Charging | 1 |
| 11***58 | Pulley-Alternator | 1 |
| 11***59 | Frame As-Alternator | 1 |
287-6361 Alternator Gp-Charging
| 10***14 | Alternator Group-Charging | 1 |
| 23***62 | Plate | 1 |
| 23***73 | Bolt; (M10x1.5x90-mm) | 1 |
235-5905 Alternator Gp-Charging
| 23***62 | Plate | 1 |
| 23***73 | Bolt; (M10x1.5x90-mm) | 1 |
| 23***05 | Alternator Group-Charging | 1 |
225-7950 Battery Gp -Standard
| 15***56 | Battery; (12-Volt, Maintenance Free)(24 V) | 1 |
| 19***29 | Clamp | 1 |
| 22***50 | Battery Group; -Standard | 1 |
225-7952 Battery Gp -Heavy Duty
| 19***29 | Clamp | 1 |
| 22***52 | Battery Group; -Heavy-Duty | 1 |
| 23***68 | Battery | 1 |
154-4233 Control Gp-Interlock
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 15***33 | Control Group-Interlock | 1 |
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
218-5780 Conversion Ar-Non-Roading -Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***80 | Conversion Ar-Non-Roading; -Nacd | 1 |
| 21***90 | Panel Ar-Instrument; -Nacd | 1 |
216-4755 Cover Gp-Fuse Panel
| 10***43 | Seal; (32-cm Each) | 0 |
| 11***71 | Puller-Minifuse | 1 |
| 16***65 | Retainer | 2 |
225-8000 Electronics Gp-Implement -Work Tool
| 12***97 | Screw-Pan Head; (No 8-32x0.375-In) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 21***58 | Control Group-Unprogrammed | 1 |
207-5262 Electronics Gp-Machine -Security
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 15***55 | Control Group-Unprogrammed; -Machine Security System | 1 |
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
216-4750 Fastener Gp-Wiring Harness
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 4 |
| 19***36 | Insert-Threaded; (M6x1-Thd) | 4 |
| 19***07 | Screw-Truss Head; (M6x1x35-mm) | 4 |
235-5904 Glow Plug Gp
| 10***59 | Glow Plug | 4 |
| 23***04 | Glow Plug Group | 1 |
| 25***90 | Plate-Connection | 1 |
218-0943 Heater Gp-Jacket Water
| 13***17 | Cap As-Dust | 1 |
| 21***12 | Cord As | 1 |
| 21***43 | Heater Group-Jacket Water | 1 |
218-0942 Heater Gp-Jacket Water
| 21***42 | Heater Group-Jacket Water | 1 |
| 22***41 | Element As-Jacket Water Heater; (120-Volt, 530-Watt) | 1 |
| 22***42 | Heater Group-Jacket Water | 1 |
239-5010 Installation Gp-Security -Kit
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
225-7991 Installation Gp-Security
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
234-7727 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***11 | Lens As | 1 |
| 23***27 | Lamp Group-Flood; -Rear | 1 |
234-4328 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 23***28 | Lamp Group-Flood; -Front, Rear, Wide Range | 1 |
142-8634 Lamp Gp-Stop & Tail
| 08***48 | Lamp; (12-Volt, 5-Watt) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 14***34 | Lamp Group-Stop & Tail; -Stop, Tail | 1 |
142-7503 Lamp Gp-Stop & Tail
| 08***48 | Lamp; (12-Volt, 5-Watt) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 14***03 | Lamp Group-Stop & Tail; -12-Volt | 1 |
128-6985 Lamp Gp-Warning Beacon -Amber, Magnetic Mount, Rotating
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 9R***42 | Plug As | 1 |
| 9R***58 | Cord As | 1 |
218-6425 Lighting Gp-Flood -Front
| 21***25 | Lighting Group-Flood; -Front | 1 |
| 23***28 | Lamp Group-Flood; -Front, Rear, Wide Range | 2 |
| 5P***39 | Grommet | 2 |
216-4746 Lighting Gp-Flood -Rear
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***26 | Switch As-Rocker; (Rear Working Lamp) | 1 |
| 19***37 | Insert-Threaded; (M8x1.25-Thd) | 2 |
216-4715 Lighting Gp-Roading
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
216-4716 Lighting Gp-Roading
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
142-8652 Lighting Gp-Stop & Tail
| 14***03 | Lamp Group-Stop & Tail; -12-Volt | 2 |
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 2 |
142-8653 Lighting Gp-Warning Beacon
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 14***53 | Lighting Group-Warning Beacon; -12-Volt | 1 |
238-8277 Sensor Gp-Temp & Press -Engine
| 23***74 | Switch-Temperature; (Engine Coolant, Cold Start) | 1 |
| 23***77 | Sensor Group-Temp & Press; -Engine | 1 |
| 32***52 | Switch-Oil Press; (Engine) | 1 |
287-6181 Starting Motor Gp-Electric
| 14***39 | Starting Motor Group-Electric; -12-Volt | 1 |
| 28***81 | Starting Motor Group-Electric | 1 |
143-0539 Starting Motor Gp-Electric
| 10***85 | Cap-Starting Motor | 1 |
| 10***12 | Kit-Contact; (Starting Motor) | 1 |
| 10***13 | Switch As; (Starting Motor)(12-Volt) | 1 |
235-5903 Starting Motor Gp-Electric -12-Volt
| 23***63 | Starting Motor Group-Electric | 1 |
| 23***03 | Starting Motor Group-Electric; -12-Volt | 1 |
224-0744 Switch Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 22***44 | Switch Group-Pressure | 1 |
| 3E***71 | Wedge; (Receptacle Lock) (3 Pin) | 1 |
184-1564 Switch Gp-Pressure -Brake Light
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***64 | Switch Group-Pressure; -Brake Light | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
225-7969 Warning Gp-Backup
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***39 | Alarm As | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
225-7948 Wiring Gp-Air Conditioner
| 10***74 | Seal-Connector | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
216-4700 Wiring Gp-Chassis
| 09***34 | Spacer; (9x20x10-mm Thk) | 3 |
| 09***33 | Screw-Machine; (M4x0.7x40-mm) | 2 |
| 10***20 | Plug As-Connector; (2-Pin) | 1 |
216-4720 Wiring Gp-Engine
| 09***34 | Spacer; (9x20x10-mm Thk) | 3 |
| 10***20 | Plug As-Connector; (2-Pin) | 1 |
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 4 |
230-3743 Wiring Gp-Horn -With Mounting
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 2 |
| 12***68 | Socket-Connector; (14-Ga) | 2 |
293-4098 Wiring Gp-Machine -Demand Fan
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 2 |
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
225-7964 Wiring Gp-Rear Lighting
| 10***41 | Terminal-Receptacle; (18-Ga To 20-Ga) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***15 | Relay As; (12-Volt)(Junction Box) | 1 |
225-7960 Wiring Gp-Work Tool -Radial Lift
| 09***33 | Screw-Machine; (M4x0.7x40-mm) | 2 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
216-4724 Wiring Gp-Work Tool -Vertical Lift
| 09***33 | Screw-Machine; (M4x0.7x40-mm) | 2 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***60 | Strap | 1 |
Engine Arrangement
218-6850 Engine Ar
| 17***54 | Engine Ar-Primary | 1 |
| 21***50 | Engine Ar | 1 |
179-1854 Engine Ar-Primary
| 17***54 | Engine Ar-Primary | 1 |
| 23***73 | Camshaft Group | 1 |
| 23***80 | Cover Group-Valve Mechanism | 1 |
218-0914 Installation Ar-Engine
| 21***20 | Wiring Group-Engine | 1 |
| 21***14 | Installation Ar-Engine | 1 |
| 21***23 | Mounting Group-Engine | 1 |
278-1238 Installation Ar-Engine
| 21***20 | Wiring Group-Engine | 1 |
| 21***23 | Mounting Group-Engine | 1 |
| 21***38 | Mounting Group-Rad & Oil Cooler | 1 |
Frame And Body
218-5660 Bumper Gp -Rear
| 14***21 | Stud | 2 |
| 15***06 | Boss | 2 |
| 21***60 | Bumper Group; -Rear | 1 |
238-7607 Conversion Ar-Roading -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
| 21***46 | Box Group-Storage | 1 |
238-7608 Conversion Ar-Roading -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
| 19***84 | Film Group; -Clearance | 1 |
218-5784 Conversion Ar-Roading -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 19***84 | Film Group; -Clearance | 1 |
| 21***46 | Box Group-Storage | 1 |
251-1513 Conversion Ar-Roading -Germany
| 11***58 | Film-Identification; (20-Km/H) | 3 |
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
218-5781 Conversion Ar-Roading -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***46 | Box Group-Storage | 1 |
| 21***81 | Conversion Ar-Roading; -Outside Nacd | 1 |
236-5114 Conversion Ar-Roading -Germany
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
236-5115 Conversion Ar-Roading -Italy
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
265-7750 Conversion Ar-Roading -Germany, Italy
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 21***15 | Lighting Group-Roading | 1 |
218-5783 Conversion Ar-Roading -Italy
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 21***15 | Lighting Group-Roading | 1 |
265-7749 Conversion Ar-Roading -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***46 | Box Group-Storage | 1 |
| 21***91 | Panel Ar-Instrument; -Eame | 1 |
218-5782 Conversion Ar-Roading -Germany
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
251-1511 Conversion Ar-Roading -Germany
| 11***58 | Film-Identification; (20-Km/H) | 3 |
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
278-1293 Conversion Gp-Roading -Italy
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 12***54 | Fastener; (Loop) (22cm) (X3) | 0 |
| 12***55 | Fastener-Hook; (18-cm Each) | 0 |
234-0793 Conversion Gp-Roading -Italy
| 12***85 | Lamp Group-Warning Beacon; -Amber, Magnetic Mount, Rotating | 1 |
| 12***54 | Fastener; (Loop) (22cm) (X3) | 0 |
| 12***55 | Fastener-Hook; (18-cm Each) | 0 |
278-1292 Conversion Gp-Roading -Germany
| 11***34 | Film-Warning; (Steering) | 1 |
| 17***15 | Bracket As | 1 |
| 17***16 | Chock | 1 |
234-0792 Conversion Gp-Roading -Germany
| 11***34 | Film-Warning; (Steering) | 1 |
| 15***42 | Plate-Information; (Maximum Weight) | 1 |
| 16***89 | Tack-Fastener | 4 |
183-7132 Counterweight Gp
| 18***31 | Block; (16.90 Kg) | 2 |
| 18***32 | Counterweight Group | 1 |
| 18***33 | Block; (33.99 Kg)(Lh) | 1 |
154-4050 Counterweight Gp
| 15***50 | Counterweight Group | 1 |
| 17***80 | Block | 14 |
| 7X***90 | Washer-Hard; (13.5x44.5x6-mm Thk) | 2 |
218-6016 Counterweight Gp
| 21***16 | Counterweight Group | 1 |
| 21***17 | Plate | 4 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 12 |
220-8135 Counterweight Gp -Kit
| 22***35 | Counterweight Group; -Kit | 1 |
| 22***36 | Plate | 1 |
| 22***37 | Plate | 1 |
218-6018 Counterweight Gp
| 21***17 | Plate | 4 |
| 21***18 | Counterweight Group | 1 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 12 |
185-9941 Counterweight Gp -Kit
| 18***31 | Block; (16.90 Kg) | 2 |
| 18***33 | Block; (33.99 Kg)(Lh) | 1 |
| 18***34 | Block; (33.99 Kg)(Rh) | 1 |
218-5803 Enclosure Gp-Engine
| 11***85 | Bumper | 2 |
| 13***40 | Locknut; (M8x1.25-Thd) | 3 |
| 14***01 | Hood As | 1 |
218-5675 Frame & Mtg Gp-Machine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***10 | Plate As | 1 |
| 14***23 | Gasket | 2 |
218-5875 Frame & Mtg Gp-Machine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***10 | Plate As | 1 |
| 14***23 | Gasket | 2 |
218-5873 Frame As-Lower
| 21***73 | Frame As-Lower | 1 |
261-6203 Frame As-Upper
| 26***03 | Frame As-Upper | 1 |
218-6562 Frame Gp-Machine
| 19***94 | Link As | 1 |
| 21***73 | Frame As-Lower | 1 |
| 21***98 | Arm As-Lift | 1 |
150-8621 Guide Gp-Lines
| 15***21 | Guide Group-Lines | 1 |
| 22***15 | Plate As | 1 |
| 24***77 | Bolt; (M8x1.25x12-mm) | 1 |
264-5864 Kit-Engine Enclosure Seal -Debris Barrier
| 12***43 | Seal; (70-cm) | 0 |
| 26***54 | Baffle | 1 |
| 26***55 | Baffle | 1 |
265-7751 Kit-Roading Conversion -Italy
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***15 | Relay As; (12-Volt)(Junction Box) | 1 |
265-7753 Kit-Roading Conversion -Germany, 20-Km/H
| 11***34 | Film-Warning; (Steering) | 1 |
| 11***58 | Film-Identification; (20-Km/H) | 3 |
| 16***62 | Plate As | 1 |
277-0657 Kit-Roading Conversion
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
257-5730 Kit-Roading Conversion -Outside Nacd
| 16***00 | Film-Warning; (Clearance) | 1 |
| 25***30 | Kit-Roading Conversion; -Outside Nacd | 1 |
277-0656 Kit-Roading Conversion
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
265-7752 Kit-Roading Conversion -Germany, 13-Km/H
| 11***34 | Film-Warning; (Steering) | 1 |
| 16***62 | Plate As | 1 |
| 16***69 | Visor Group-Cab | 1 |
233-5990 Lifting Gp-Machine -Single Point
| 09***25 | Pin-Clevis | 1 |
| 15***54 | Bracket As-Lift | 1 |
| 15***56 | Plate | 4 |
188-0147 Lifting Gp-Machine -4-Point
| 14***26 | Plate-Lift | 4 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
218-5969 Lifting Gp-Machine -Single Point
| 09***25 | Pin-Clevis | 1 |
| 15***54 | Bracket As-Lift | 1 |
| 15***56 | Plate | 4 |
233-5991 Lifting Gp-Machine -4-Point
| 14***26 | Plate-Lift | 4 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
| 23***92 | Plate As | 1 |
190-7994 Link As
| 19***94 | Link As | 1 |
| 6K***99 | Bearing-Sleeve | 4 |
236-5057 Mirror & Mtg Gp-Rear View
| 13***66 | Mirror Group-Rear View | 2 |
| 14***71 | Clamp; (Top)(Top) | 1 |
| 14***72 | Clamp; (Bottom)(Bottom) | 1 |
236-5060 Mirror & Mtg Gp-Rear View
| 13***66 | Mirror Group-Rear View | 2 |
| 14***71 | Clamp; (Top)(Top) | 1 |
| 14***72 | Clamp; (Bottom)(Bottom) | 1 |
173-3021 Mounting Gp-Registration -With Wiring & Lights
| 17***21 | Mounting Group-Registration; -With Wiring & Lights | 1 |
| 17***36 | Plate | 1 |
| 19***62 | Lamp Group-Registration Plate | 1 |
225-7963 Mounting Gp-Registration
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 4 |
175-4228 Mounting Gp-Roading Lights -Rear
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 4 |
| 15***71 | Kit-Connecting Plug; (4-Pin) | 1 |
261-6370 Suppression Gp-Sound
| 17***79 | Insulation | 6 |
| 26***70 | Suppression Group-Sound | 1 |
| 26***71 | Insulation | 2 |
278-1279 Suppression Gp-Sound -Belt Guard
| 27***79 | Suppression Group-Sound; -Belt Guard | 1 |
| 28***97 | Guard Group-Belt | 1 |
233-5615 Suppression Gp-Sound -Hood
| 17***79 | Insulation | 2 |
| 23***15 | Suppression Group-Sound; -Hood | 1 |
| 23***47 | Insulation | 1 |
257-7400 Suppression Gp-Sound -Engine
| 01***80 | Lockwasher | 6 |
| 24***59 | Cover-Insulation | 1 |
| 24***60 | Cover-Insulation | 1 |
Fuel System
218-5566 Cable Gp-Governor Control
| 21***66 | Cable Group-Governor Control | 1 |
| 25***77 | Pin As-Spring | 1 |
| 28***70 | End-Yoke Rod | 1 |
218-5602 Control Gp-Governor
| 21***65 | Pedal Group-Governor; -Includes Lever | 1 |
| 21***02 | Control Group-Governor | 1 |
| 23***96 | Screw-Flat Head; (M6x1x35-mm) | 4 |
235-5901 Lines Gp-Fuel Injection
| 09***35 | Cap | 1 |
| 09***90 | Shim (1.800mm Thick) | 0 |
| 09***94 | Shim (0.700mm Thick) | 0 |
218-0930 Lines Gp-Fuel Prm & Filter
| 14***28 | Elbow | 1 |
| 18***07 | Clamp-Hose | 1 |
| 19***76 | Hose | 1 |
218-0929 Lines Gp-Fuel Prm & Filter
| 14***28 | Elbow | 1 |
| 15***92 | Hose | 1 |
| 18***07 | Clamp-Hose | 1 |
235-5902 Pump Gp-Fuel Injection
| 14***17 | Bolt; (M10x1.25x25-mm) | 1 |
| 19***54 | Bolt; (M10x1.25x25-mm) | 1 |
| 21***10 | Nut | 1 |
232-5877 Pump Gp-Fuel Prm & Prim Filter -Water Separator
| 11***01 | Bowl As-Water Collection | 1 |
| 11***18 | Ring-Retaining | 1 |
| 12***14 | Kit-Seal; (Water Separator) | 1 |
305-6411 Pump Gp-Fuel Prm & Prim Filter
| 11***01 | Bowl As-Water Collection | 1 |
| 11***18 | Ring-Retaining | 1 |
| 12***14 | Kit-Seal; (Water Separator) | 1 |
Hydraulic System
193-0447 Accumulator & Mtg Gp-Hydraulic
| 14***86 | Accumulator Group-Hydraulic; -Charged | 1 |
| 19***47 | Accumulator & Mtg Group-Hydraulic; -Work Tool | 1 |
| 19***31 | Elbow; (45-Deg) | 1 |
149-0686 Accumulator Gp-Hydraulic -Charged
| 14***86 | Accumulator Group-Hydraulic; -Charged | 1 |
230-5406 Cylinder & Mtg Gp-Angle Blade
| 06***43 | Ring-Snap | 1 |
| 21***55 | Pin As | 1 |
| 21***43 | Bushing | 1 |
218-5799 Cylinder & Mtg Gp-Lift Arm
| 14***32 | Pin As | 1 |
| 14***80 | Lever | 1 |
| 14***81 | Bracket | 1 |
218-5899 Cylinder & Mtg Gp-Lift Arm
| 08***97 | Washer; (13x50x6-mm Thk) | 2 |
| 11***37 | Washer; (46x70x1-mm Thk)(1mm`Thk) | 12 |
| 14***32 | Pin As | 2 |
293-6264 Cylinder Gp-Bucket
| 26***41 | Kit-Seal | 1 |
| 29***64 | Cylinder Group-Bucket | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
154-5018 Cylinder Gp-Bucket
| 15***18 | Cylinder Group-Bucket | 1 |
| 16***13 | Kit-Seal | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
156-5512 Cylinder Gp-Grapple
| 15***12 | Cylinder Group-Grapple | 1 |
| 16***13 | Kit-Seal | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
164-9295 Cylinder Gp-Grapple
| 16***95 | Cylinder Group-Grapple | 1 |
| 17***85 | Kit-Seal | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
278-1975 Cylinder Gp-Grapple -Industrial
| 25***97 | Bearing-Sleeve | 1 |
| 25***42 | Bearing-Sleeve | 1 |
| 27***70 | Kit-Seal; (Hydraulic Cylinder) | 1 |
255-0943 Cylinder Gp-Grapple
| 25***97 | Bearing-Sleeve | 1 |
| 25***43 | Cylinder Group-Grapple | 1 |
| 28***91 | Kit-Seal | 1 |
278-1969 Cylinder Gp-Hydraulic
| 25***97 | Bearing-Sleeve | 1 |
| 27***69 | Cylinder Group-Hydraulic | 1 |
| 27***70 | Kit-Seal; (Hydraulic Cylinder) | 1 |
192-2640 Cylinder Gp-Hydraulic -Coupler
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
225-9521 Cylinder Gp-Hydraulic -Angle Blade
| 17***58 | Kit-Seal | 1 |
| 21***55 | Rod End As | 1 |
| 22***21 | Cylinder Group-Hydraulic; -Angle Blade | 1 |
230-3695 Cylinder Gp-Lift -Rh
| 21***23 | Kit-Seal | 1 |
| 23***95 | Cylinder Group-Lift; -Rh | 1 |
230-3705 Cylinder Gp-Lift
| 21***24 | Kit-Seal; (Lift) | 1 |
| 23***05 | Cylinder Group-Lift | 1 |
230-3685 Cylinder Gp-Lift -Lh
| 21***23 | Kit-Seal | 1 |
| 23***85 | Cylinder Group-Lift; -Lh | 1 |
230-3687 Cylinder Gp-Tilt -Lh
| 21***22 | Kit-Seal | 1 |
| 23***87 | Cylinder Group-Tilt; -Lh | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
230-3697 Cylinder Gp-Tilt -Rh
| 21***22 | Kit-Seal | 1 |
| 23***97 | Cylinder Group-Tilt; -Rh | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
218-5841 Fitting Gp-Hydraulic -Quick Disconnect, Female, High Flow
| 21***41 | Fitting Group-Hydraulic; -Quick Disconnect, Female, High Flow | 1 |
| 21***45 | Fitting As; (Quick Disconnect, Female) | 1 |
| 21***46 | Fitting As; (Quick Disconnect, Female) | 1 |
218-5840 Fitting Gp-Hydraulic -Quick Disconnect, Male, High Flow
| 21***40 | Fitting Group-Hydraulic; -Quick Disconnect, Male, High Flow | 1 |
| 21***43 | Fitting As; (Quick Disconnect, Male) | 1 |
| 21***44 | Fitting As; (Quick Disconnect, Male) | 1 |
218-5710 Hydraulic Ar -Work Tool Positioner
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***16 | Switch Group-Rocker; -Work Tool Positioner | 1 |
| 21***10 | Hydraulic Ar; -Work Tool Positioner | 1 |
218-6620 Hydraulic Ar
| 19***47 | Accumulator & Mtg Group-Hydraulic; -Work Tool | 1 |
| 21***29 | Valve & Mtg Group-Control | 1 |
| 21***31 | Lines Group-Pilot; -Direction, Speed | 1 |
278-1269 Hydraulic Ar
| 19***47 | Accumulator & Mtg Group-Hydraulic; -Work Tool | 1 |
| 21***29 | Valve & Mtg Group-Control | 1 |
| 21***31 | Lines Group-Pilot; -Direction, Speed | 1 |
278-1251 Hydraulic Ar
| 19***47 | Accumulator & Mtg Group-Hydraulic; -Work Tool | 1 |
| 21***22 | Valve & Mtg Group-Control | 1 |
| 21***24 | Filter & Lines Group-Hydraulic | 1 |
218-5750 Hydraulic Ar
| 21***31 | Lines Group-Lift Cylinder | 1 |
| 21***32 | Lines Group-Tilt Cylinder | 1 |
| 21***50 | Hydraulic Ar | 1 |
218-5751 Hydraulic Ar
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 14***16 | Switch Group-Rocker; -Work Tool Positioner | 1 |
| 21***29 | Manifold & Mtg Group-Control; -Work Tool Positioner | 1 |
218-6150 Hydraulic Ar -Without Work Tool Positioner
| 21***50 | Hydraulic Ar; -Without Work Tool Positioner | 1 |
| 21***68 | Lines Group-Lift Cylinder | 1 |
| 21***70 | Lines Group-Tilt Cylinder | 1 |
218-6220 Hydraulic Ar
| 19***47 | Accumulator & Mtg Group-Hydraulic; -Work Tool | 1 |
| 21***22 | Valve & Mtg Group-Control | 1 |
| 21***24 | Filter & Lines Group-Hydraulic | 1 |
218-6623 Kit-Joystick Conversion -Dual Control
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 3 |
233-5584 Kit-Joystick Conversion -Kit, Dual Control
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 14***25 | Connector As. | 7 |
218-6755 Kit-Quick Coupler Conversion -Hydraulic
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 11***90 | Fuse; (10 Amp) | 1 |
| 12***67 | Hose | 0 |
218-6756 Kit-Quick Coupler Conversion -Hydraulic
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 11***90 | Fuse; (10 Amp) | 1 |
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
285-6113 Lines Gp-Bucket -Utility
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
199-8306 Lines Gp-Bucket
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
154-5051 Lines Gp-Bucket
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
154-5052 Lines Gp-Bucket
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
279-5415 Lines Gp-Bucket -Multipurpose
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
154-5019 Lines Gp-Bucket
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
293-0140 Lines Gp-Bucket -Multipurpose
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
279-5412 Lines Gp-Bucket -Industrial
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
279-5413 Lines Gp-Bucket -Multipurpose
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
279-5416 Lines Gp-Bucket -Multipurpose
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
279-5414 Lines Gp-Bucket -Multipurpose
| 14***19 | Connector As | 2 |
| 15***56 | Tee As | 1 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
177-1986 Lines Gp-Connecting
| 14***19 | Connector As | 2 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
161-0187 Lines Gp-Grapple
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
165-8733 Lines Gp-Grapple
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 15***95 | Fitting As; (Quick Disconnect, Male) | 1 |
286-9250 Lines Gp-Grapple
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 16***89 | Hose As | 2 |
286-9279 Lines Gp-Grapple
| 14***19 | Connector As | 2 |
| 15***94 | Coupler As-Quick Disconnect; (Female)(Quick Disconnect) | 1 |
| 16***89 | Hose As | 2 |
218-6575 Lines Gp-Hydraulic Fan
| 14***15 | Connector As | 1 |
| 14***16 | Connector Group | 2 |
| 21***84 | Hose As | 1 |
233-5665 Lines Gp-Hydraulic Fan
| 14***15 | Connector As | 3 |
| 14***16 | Connector Group | 3 |
| 21***84 | Hose As | 1 |
218-5625 Lines Gp-Hydraulic Oil Cooler
| 09***67 | Spacer; (10.5x2x45-mm Thk) | 1 |
| 10***15 | Elbow Group | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
218-6572 Lines Gp-Hydraulic Oil Cooler
| 09***67 | Spacer; (10.5x2x45-mm Thk) | 1 |
| 10***15 | Elbow Group | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
218-6168 Lines Gp-Lift Cylinder
| 14***41 | Connector Group | 2 |
| 19***74 | Hose As | 2 |
| 19***75 | Hose As | 2 |
218-5733 Lines Gp-Lift Cylinder
| 14***97 | Block | 2 |
| 14***15 | Connector As | 1 |
| 14***41 | Connector Group | 2 |
218-5731 Lines Gp-Lift Cylinder
| 14***97 | Block | 2 |
| 14***41 | Connector Group | 2 |
| 18***73 | Tube As | 2 |
218-5711 Lines Gp-Lift Cylinder
| 14***15 | Connector As | 1 |
| 14***41 | Connector Group | 2 |
| 14***90 | Elbow Group | 1 |
218-5617 Lines Gp-Lowering Control -Manual
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 14***65 | Elbow | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
218-5834 Lines Gp-Lowering Control -Manual
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 1 |
218-5631 Lines Gp-Pilot -Direction, Speed
| 14***16 | Connector Group | 2 |
| 14***25 | Connector As. | 5 |
| 14***69 | Adapter; (90° Elbow Orfs/Orb) | 2 |
218-5835 Lines Gp-Pilot -Work Tool
| 12***50 | Valve-Check; (Quick Coupler Solenoid) | 1 |
| 14***25 | Connector As. | 9 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
261-6147 Lines Gp-Pump
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***01 | Elbow | 1 |
| 14***35 | Connect Group; (Each Includes) | 1 |
218-5626 Lines Gp-Pump
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***01 | Elbow | 1 |
| 15***46 | Adapter Group | 1 |
218-5856 Lines Gp-Pump
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***35 | Connect Group; (Each Includes) | 1 |
| 14***90 | Elbow Group | 1 |
261-6148 Lines Gp-Pump
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 14***35 | Connect Group; (Each Includes) | 2 |
| 15***73 | Plug As | 1 |
218-5734 Lines Gp-Tilt Cylinder
| 11***15 | Plate-Cover | 2 |
| 14***98 | Clip | 2 |
| 14***34 | Hose As | 4 |
218-5712 Lines Gp-Tilt Cylinder
| 10***03 | Plate-Cover | 2 |
| 14***34 | Hose As | 4 |
| 14***15 | Connector As | 2 |
218-6170 Lines Gp-Tilt Cylinder
| 10***03 | Plate-Cover | 2 |
| 14***34 | Hose As | 4 |
| 14***15 | Connector As | 2 |
218-5732 Lines Gp-Tilt Cylinder
| 11***15 | Plate-Cover | 2 |
| 14***98 | Clip | 2 |
| 14***34 | Hose As | 4 |
218-5725 Lines Gp-Work Tool
| 10***29 | Stud; (M10x1.5-Thd) | 1 |
| 14***18 | Connector As | 2 |
| 14***27 | Connector Group | 2 |
218-5830 Lines Gp-Work Tool
| 10***29 | Stud; (M10x1.5-Thd) | 1 |
| 12***13 | Bolt; (M8x1.25x55-mm) | 1 |
| 14***18 | Connector As | 2 |
218-6520 Manifold & Lines Gp-Coupler
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
| 14***25 | Connector As. | 4 |
218-5940 Manifold & Lines Gp-Coupler
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 12***56 | Film; (Warning) (No Step) (On Top Of Hood Behind Cab On Each Side) (On Each Fender Flare) | 1 |
| 14***25 | Connector As. | 4 |
218-5976 Manifold & Mtg Gp-Control -Work Tool Positioner
| 21***76 | Manifold & Mtg Group-Control; -Work Tool Positioner | 1 |
| 21***77 | Plate As | 1 |
| 22***18 | Manifold & Solenoid Group-Control; -Work Tool Positioner | 1 |
218-5729 Manifold & Mtg Gp-Control -Work Tool Positioner
| 21***29 | Manifold & Mtg Group-Control; -Work Tool Positioner | 1 |
| 22***08 | Manifold & Solenoid Group-Control; -Work Tool Positioner | 1 |
| 7X***35 | Bolt; (M6x1x60-mm) | 2 |
223-8418 Manifold & Solenoid Gp-Control -Work Tool Positioner
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 1 |
| 15***79 | Kit-Seal; (Relief Valve, Conveyor Cont) | 1 |
224-9408 Manifold & Solenoid Gp-Control -Work Tool Positioner
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 15***79 | Kit-Seal; (Relief Valve, Conveyor Cont) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
233-7128 Manifold Gp-Control -Quick Coupler
| 10***08 | Kit-Seal; (Solenoid Valve, Quick Steer) | 1 |
| 23***28 | Manifold Group-Control; -Quick Coupler | 1 |
| 23***26 | Coil As | 2 |
218-6329 Motor & Mtg Gp-Hydraulic Fan
| 21***29 | Motor & Mtg Group-Hydraulic Fan | 1 |
| 22***62 | Motor Group-Gear; -Hydraulic Fan | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 2 |
261-6124 Motor & Mtg Gp-Hydraulic Fan
| 10***61 | Wire Assembly; (Rear) | 1 |
| 13***45 | Pad; (Connector) | 1 |
| 26***24 | Motor & Mtg Group-Hydraulic Fan | 1 |
307-3034 Motor Gp-Gear
| 21***77 | Seal-O-Ring | 1 |
| 22***40 | Valve Group-Relief; (Gear Motor) | 1 |
| 27***16 | Kit-Seal; (Gear Motor) | 1 |
218-6840 Motor Gp-Gear
| 09***94 | Ring-Retaining | 1 |
| 21***40 | Motor Group-Gear; -Refrigerant Compressor | 1 |
| 23***26 | Seal-Shaft | 1 |
289-6360 Motor Gp-Gear -Compressor
| 08***69 | Bolt-Socket Head; (M10x1.5x130-mm) | 4 |
| 27***16 | Kit-Seal; (Gear Motor) | 1 |
| 28***60 | Motor Group-Gear; -Compressor | 1 |
307-3038 Motor Gp-Gear -Hydraulic Fan
| 09***94 | Ring-Retaining | 1 |
| 21***68 | Seal-O-Ring; (11.89-mm Id) | 1 |
| 23***86 | Seal Group-Lip Type | 1 |
225-9262 Motor Gp-Gear -Hydraulic Fan
| 09***94 | Ring-Retaining | 1 |
| 22***62 | Motor Group-Gear; -Hydraulic Fan | 1 |
| 22***40 | Valve Group-Relief; (Gear Motor) | 1 |
269-9467 Motor Gp-Gear
| 09***94 | Ring-Retaining | 1 |
| 23***86 | Seal Group-Lip Type | 1 |
| 26***67 | Motor Group-Gear | 1 |
156-0891 Mounting Gp-Cylinder
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***13 | Plate | 1 |
| 15***41 | Pin | 2 |
154-5011 Mounting Gp-Cylinder
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***12 | Pin | 2 |
| 15***13 | Pin | 2 |
286-9248 Mounting Gp-Cylinder -Grapple Bucket
| 15***41 | Pin | 2 |
| 15***42 | Pin | 2 |
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
165-8731 Mounting Gp-Cylinder
| 15***13 | Pin | 2 |
| 16***31 | Mounting Group-Cylinder; -Utility | 1 |
| 6V***89 | Locknut; (M8x1.25-Thd) | 2 |
142-8714 Plug Gp-Pilot Valve
| 14***14 | Plug Group-Pilot Valve | 1 |
| 14***07 | Plug; (Hex Head) (-6 Orb) (Current) (16***35 Friction Disc Interchangeable With 11***47) (Use All Of One Part Number) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
218-5825 Pump & Mtg Gp-Gear
| 10***04 | Bolt; (Socket Head) (M10x1.5x30mm) | 2 |
| 21***25 | Pump & Mtg Group-Gear | 1 |
| 22***27 | Pump Group-Gear; -Charge | 1 |
218-5826 Pump & Mtg Gp-Work Tool
| 21***26 | Tappet, Tappet; Tappet, Pump & Mtg Group-Work Tool | 1 |
| 22***05 | Pump Group-Piston; -High Flow | 1 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 2 |
261-6097 Pump & Mtg Gp-Work Tool
| 10***04 | Bolt; (Socket Head) (M10x1.5x30mm) | 2 |
| 22***05 | Pump Group-Piston; -High Flow | 1 |
| 26***97 | Pump & Mtg Group-Work Tool | 1 |
269-9426 Pump Gp-Gear
| 09***94 | Ring-Retaining | 1 |
| 23***39 | Seal; (Shaft) | 2 |
| 26***26 | Pump Group-Gear | 1 |
220-8127 Pump Gp-Gear -Charge
| 09***94 | Ring-Retaining | 1 |
| 22***27 | Pump Group-Gear; -Charge | 1 |
| 23***39 | Seal; (Shaft) | 2 |
224-9405 Pump Gp-Piston -High Flow
| 11***04 | Bolt-Socket Head; (M12x1.75x45-mm) | 4 |
| 22***05 | Pump Group-Piston; -High Flow | 1 |
| 23***86 | Kit-Bearing; (Generator Pump) | 1 |
233-5980 Tank & Mtg Gp-Hydraulic
| 15***14 | Bracket | 1 |
| 20***91 | Tank Group-Hydraulic | 1 |
| 20***29 | Breather; (Inline)(Breather)(Hydraulic Oil) | 1 |
204-1491 Tank Gp-Hydraulic
| 09***74 | Bolt-Socket Head; (M5x0.8x12-mm) | 6 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***56 | Seal-O-Ring | 1 |
218-5629 Valve & Mtg Gp-Control
| 21***29 | Valve & Mtg Group-Control | 1 |
| 21***61 | Bracket | 1 |
| 22***38 | Valve Group-Control; -Work Tool, 4-Function | 1 |
218-5622 Valve & Mtg Gp-Control
| 21***22 | Valve & Mtg Group-Control | 1 |
| 21***61 | Bracket | 1 |
| 22***28 | Valve Group-Control; -Work Tool,4-Function | 1 |
209-0640 Valve & Mtg Gp-Solenoid
| 14***44 | Valve Group-Solenoid | 1 |
| 18***69 | Manifold | 1 |
| 20***40 | Valve & Mtg Group-Solenoid | 1 |
220-8128 Valve Gp-Control -Work Tool,4-Function
| 18***54 | Valve Group-Solenoid; -Auxiliary | 2 |
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 2 |
| 20***71 | Cap | 1 |
220-8138 Valve Gp-Control -Work Tool, 4-Function
| 18***54 | Valve Group-Solenoid; -Auxiliary | 2 |
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 2 |
| 20***71 | Cap | 1 |
112-1817 Valve Gp-Manual
| 11***17 | Valve Group-Manual; -Ride Control-Hydraulic Lockout | 1 |
| 11***61 | Seal Kit; (Includes Seals, Thrust Ring, Stem And Connectors) | 1 |
| 20***71 | Valve Group-Manual; (Coupler Pin, Lift Arm Lwr Cont) | 1 |
220-8126 Valve Gp-Pilot -Work Tool
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***65 | Kit-Seal; (Pilot Valve) | 1 |
| 16***78 | Kit-Pilot Valve; (Spring)(Pilot Valve Lift & Dump) | 1 |
299-9116 Valve Gp-Pilot
| 15***65 | Kit-Seal; (Pilot Valve) | 1 |
| 16***78 | Kit-Pilot Valve; (Spring)(Pilot Valve Lift & Dump) | 1 |
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 1 |
299-9120 Valve Gp-Pilot
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***65 | Kit-Seal; (Pilot Valve) | 1 |
| 16***78 | Kit-Pilot Valve; (Spring)(Pilot Valve Lift & Dump) | 1 |
233-5733 Valve Gp-Pilot
| 1M***76 | Lockwasher | 2 |
| 23***33 | Valve Group-Pilot | 1 |
| 30***42 | Kit-Plunger | 1 |
233-5732 Valve Gp-Pilot
| 1M***76 | Lockwasher | 2 |
| 23***32 | Valve Group-Pilot | 1 |
| 30***18 | Gear Cover Gasket, Kit-Detent | 1 |
218-6119 Valve Gp-Pilot -Direction, Speed
| 12***04 | Plate | 1 |
| 15***65 | Kit-Seal; (Pilot Valve) | 1 |
| 16***78 | Kit-Pilot Valve; (Spring)(Pilot Valve Lift & Dump) | 1 |
211-3014 Valve Gp-Shuttle
| 12***98 | Seat | 1 |
| 12***99 | Seat | 1 |
| 13***49 | Connector | 1 |
144-1644 Valve Gp-Solenoid
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 12***48 | Kit-Seal; (Solenoid Valve) | 1 |
| 14***43 | Solenoid As | 1 |
216-0610 Valve Gp-Solenoid
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 17***92 | Kit-Seal; (Solenoid Valve) | 1 |
| 21***10 | Valve Group-Solenoid | 1 |
231-6287 Valve Gp-Solenoid -A/C Compressor
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***70 | Nut; (1/2-20-2b-Thd) | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
185-4254 Valve Gp-Solenoid
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 18***54 | Valve Group-Solenoid; -Auxiliary | 1 |
| 21***73 | Nut; (1/2-28-Thd) | 1 |
195-9700 Valve Gp-Solenoid -12-Volt
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 1 |
| 20***71 | Kit-Seal; (Solenoid Valve) | 1 |
| 21***61 | Flange | 1 |
Implements
218-5898 Arm As-Lift
| 21***98 | Arm As-Lift | 1 |
| 4K***09 | Bearing-Sleeve | 4 |
| 6K***48 | Bearing-Sleeve | 4 |
Lubrication System
287-6016 Breather Gp
| 11***68 | Clip | 2 |
| 15***28 | Clamp | 1 |
| 19***22 | Bolt As; (M8x1.25x22-mm) | 2 |
235-5897 Filter Gp-Engine Oil
| 09***37 | Seal-O-Ring | 1 |
| 09***71 | Seal-O-Ring (Id=94.40mm) | 1 |
| 1R***34 | Filter-Engine Oil | 1 |
314-9901 Filter Gp-Engine Oil
| 09***37 | Seal-O-Ring | 1 |
| 09***71 | Seal-O-Ring (Id=94.40mm) | 1 |
| 1R***34 | Filter-Engine Oil | 1 |
235-5898 Fumes Disposal Gp
| 23***37 | Clip-Hose | 1 |
| 23***38 | Clip | 3 |
| 23***39 | Pipe | 1 |
235-5888 Gauge Gp-Oil Level (Dipstick)
| 23***12 | Guide | 1 |
| 23***13 | Stay | 1 |
| 23***56 | Gauge-Oil; (Dipstick)(Engine Oil) | 1 |
287-5377 Lines Gp-Engine Oil
| 23***94 | Strainer As-Oil; (Engine) | 1 |
| 23***13 | Seal-O-Ring | 1 |
| 28***77 | Lines Group-Engine Oil | 1 |
235-5895 Pump Gp-Engine Oil
| 10***44 | Nut | 1 |
| 10***83 | Seal-O-Ring | 1 |
| 11***41 | Pump As-Oil | 1 |
287-5665 Valve Gp-Engine Oil Relief
| 10***25 | Valve As; (Oil Bypass)(Engine) | 1 |
| 23***96 | Gasket | 1 |
| 23***96 | Gasket | 1 |
Machine Arrangement
218-5610 Chassis Ar
| 15***21 | Guide Group-Lines | 1 |
| 21***00 | Wiring Group-Chassis | 1 |
| 21***18 | Mounting Group-Pump | 1 |
218-5810 Chassis Ar
| 15***21 | Guide Group-Lines | 1 |
| 21***00 | Wiring Group-Chassis | 1 |
| 21***18 | Mounting Group-Pump | 1 |
218-6268 Common Ar
| 21***14 | Installation Ar-Engine | 1 |
| 21***00 | Power Train Ar | 1 |
| 21***10 | Chassis Ar | 1 |
278-1248 Common Ar
| 15***50 | Counterweight Group | 1 |
| 21***00 | Power Train Ar | 1 |
| 21***10 | Chassis Ar | 1 |
278-1268 Common Ar
| 21***00 | Power Train Ar | 1 |
| 21***10 | Chassis Ar | 1 |
| 21***59 | Film Group | 1 |
218-6248 Common Ar
| 15***50 | Counterweight Group | 1 |
| 21***14 | Installation Ar-Engine | 1 |
| 21***00 | Power Train Ar | 1 |
278-5423 Conversion Ar-Machine -Germany
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
278-5377 Conversion Ar-Machine -Italy
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 21***15 | Lighting Group-Roading | 1 |
278-5422 Conversion Ar-Machine -Germany
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
278-1222 Conversion Ar-Machine -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 19***84 | Film Group; -Clearance | 1 |
| 21***46 | Box Group-Storage | 1 |
261-6190 Conversion Ar-Machine -Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***24 | Radiator & Oil Cooler Mtg Group | 1 |
| 21***40 | Guard Group-Belt | 1 |
278-1223 Conversion Ar-Machine -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
| 19***84 | Film Group; -Clearance | 1 |
278-5452 Conversion Ar-Machine -Germany, 2-Speed
| 11***58 | Film-Identification; (20-Km/H) | 3 |
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
278-4746 Conversion Ar-Machine -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***46 | Box Group-Storage | 1 |
| 21***91 | Panel Ar-Instrument; -Eame | 1 |
252-0419 Conversion Ar-Machine -Outside Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
| 21***46 | Box Group-Storage | 1 |
278-5451 Conversion Ar-Machine -Germany, 2-Speed
| 11***58 | Film-Identification; (20-Km/H) | 3 |
| 17***22 | Visor Group-Cab | 1 |
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
278-5378 Conversion Ar-Machine -Italy
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 18***47 | Lifting Group-Machine; -4-Point | 1 |
261-6140 Conversion Ar-Machine -Nacd
| 14***52 | Lighting Group-Stop & Tail | 1 |
| 21***24 | Radiator & Oil Cooler Mtg Group | 1 |
| 21***40 | Guard Group-Belt | 1 |
Operator Station
186-6190 Accumulator Gp-Refrigerant -With Desiccant
| 18***90 | Accumulator Group-Refrigerant; -With Desiccant | 1 |
176-3900 Accumulator Gp-Refrigerant -With Desiccant
| 17***00 | Accumulator Group-Refrigerant; -With Desiccant | 1 |
233-5650 Air Conditioner Ar
| 21***19 | Lines Group-Heater | 1 |
| 21***80 | Lines Group-Air Conditioner | 1 |
| 21***48 | Condenser & Mtg Group-Refrigerant | 1 |
218-6405 Air Conditioner Gp
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 11***31 | Switch-Temperature; (Air Conditioner) | 1 |
| 18***15 | Clip | 10 |
218-6404 Air Conditioner Gp
| 21***02 | Insulation As | 1 |
| 21***04 | Air Conditioner Group | 1 |
| 21***05 | Air Conditioner Group | 1 |
320-1389 Arm Gp-Window Wiper
| 13***91 | Nozzle As-Washer | 1 |
| 19***71 | Hose; (116-cm) | 0 |
| 24***66 | Clip-Washer Hose | 2 |
236-4830 Armrest & Mounting Gp
| 19***37 | Insert-Threaded; (M8x1.25-Thd) | 2 |
| 19***39 | Stud | 4 |
| 21***42 | Plate | 2 |
236-4833 Armrest Gp
| 10***62 | Screw-Machine; (4-40x0.63-In) | 4 |
| 13***16 | Stud-Ball | 2 |
| 14***28 | Locknut; (4-40-Thd) | 4 |
216-6146 Box Gp-Storage
| 21***45 | Box As-Storage | 1 |
| 21***46 | Box Group-Storage | 1 |
| 22***91 | Latch As | 1 |
218-6420 Box Gp-Storage -Literature
| 15***71 | Compartment As | 1 |
| 19***35 | Insert-Threaded; (M6x1-Thd) | 4 |
| 21***20 | Box Group-Storage; -Literature | 1 |
218-6350 Cab Ar-Enclosed Rops
| 19***23 | Window Group-Cab; -Rear | 1 |
| 21***50 | Fastener Group-Wiring Harness | 1 |
| 21***50 | Cab Ar-Enclosed Rops | 1 |
218-6367 Cab Gp-Enclosed Rops
| 21***67 | Cab Group-Enclosed Rops | 1 |
322-5614 Cab Gp-Enclosed Rops
| 21***86 | Button | 7 |
| 21***67 | Cab Group-Enclosed Rops | 1 |
| 28***72 | Window | 1 |
298-7198 Cable Gp-Control -Manual Lowering
| 27***74 | Cable Group-Control | 1 |
| 29***97 | Handle Group | 1 |
| 29***98 | Cable Group-Control; -Manual Lowering | 1 |
276-0074 Cable Gp-Control
| 27***74 | Cable Group-Control | 1 |
| 8T***42 | Rod End-Yoke | 1 |
| 8T***44 | Pin As-Spring | 1 |
218-6832 Compressor & Motor Gp-Refrig
| 21***32 | Compressor & Motor Group-Refrig | 1 |
| 21***33 | Compressor Group-Refrigerant | 1 |
| 21***40 | Motor Group-Gear; -Refrigerant Compressor | 1 |
218-6830 Compressor & Mtg Gp-Refrig
| 21***30 | Compressor & Mtg Group-Refrig | 1 |
| 21***32 | Compressor & Motor Group-Refrig | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 3 |
218-6148 Condenser & Mtg Gp-Refrigerant
| 11***63 | Clip-Spring | 3 |
| 21***60 | Shroud As | 1 |
| 21***48 | Condenser & Mtg Group-Refrigerant | 1 |
231-4259 Control Gp-Handle -Rh
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 11 |
231-4258 Control Gp-Handle -Lh
| 17***91 | Kit-Receptacle; (12-Pin)(12 Pin) | 1 |
| 17***83 | Locknut; (M4x0.7-Thd) | 3 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 7 |
218-6570 Control Gp-Pilot Operated Hyd
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 4 |
| 11***60 | Strap | 1 |
218-6925 Control Gp-Pilot Operated Hyd
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***01 | Resistor As; (390-Ohm, 2-Watt) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 1 |
218-6924 Control Gp-Pilot Operated Hyd
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***01 | Resistor As; (390-Ohm, 2-Watt) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 1 |
218-5947 Control Gp-Pilot Operated Hyd
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 11***60 | Strap | 1 |
| 11***90 | Fuse; (10 Amp) | 1 |
218-5933 Control Gp-Pilot Operated Hyd
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 11***60 | Strap | 1 |
| 11***90 | Fuse; (10 Amp) | 1 |
276-5708 Coupling Gp-Drive -Refrigerant Compressor, Motor
| 21***36 | Coupling Group-Drive; (Refrigerant Compressor, Motor) | 1 |
| 21***37 | Coupling | 1 |
| 21***38 | Hub; (Compressor) | 1 |
218-6419 Cover Gp-Console -Without Air Conditioner, Heater
| 17***05 | Screw-Button Head; (M6 X 1.0 X) | 8 |
| 21***89 | Console; (Rh) | 1 |
| 21***91 | Console; (Lh) | 1 |
218-6418 Cover Gp-Console
| 11***58 | Washer; (6.5x17x1-mm Thk) | 6 |
| 12***43 | Seal; (70-cm) | 0 |
| 21***86 | Cover As | 1 |
142-9118 Cover Gp-Instrument Panel -Service Meter
| 10***06 | Screw-Pan Head; (6-19x0.37-In) | 2 |
| 10***04 | Suppressor As-Arc | 1 |
| 14***18 | Cover Group-Instrument Panel; -Service Meter | 1 |
223-0600 Door & Mtg Gp-Cab -Glass
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
218-6440 Door & Mtg Gp-Cab -Polycarbonate
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
276-3440 Door Gp-Cab -Polycarbonate
| 03***28 | Grommet | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
218-6431 Door Gp-Cab -Glass
| 21***31 | Door Group-Cab; -Glass | 1 |
| 22***09 | Glass-Cab; (Door) | 1 |
| 22***10 | Glass-Cab; (Door) | 1 |
223-0616 Door Gp-Cab -Glass
| 03***28 | Grommet | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
276-3615 Door Gp-Cab -Polycarbonate
| 27***15 | Door Group-Cab; -Polycarbonate | 1 |
| 27***32 | Seal | 1 |
| 28***59 | Frame As | 1 |
218-6441 Door Gp-Cab -Polycarbonate
| 03***28 | Grommet | 1 |
| 10***45 | Blade As-Wiper; (600-mm) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
218-6394 Duct Gp-Cab Air
| 14***71 | Louver As | 6 |
| 17***05 | Screw-Button Head; (M6 X 1.0 X) | 8 |
| 21***94 | Duct Group-Cab Air | 1 |
231-7327 Frame Gp-Window -Lh
| 23***27 | Frame Group-Window; -Lh | 1 |
| 23***28 | Frame As-Window; (Lh) | 1 |
| 23***29 | Kit-Latch | 1 |
231-7325 Frame Gp-Window -Rh
| 23***25 | Frame Group-Window; -Rh | 1 |
| 23***26 | Frame As-Window; (Rh) | 1 |
| 23***29 | Kit-Latch | 1 |
216-4712 Gauge & Warning Gp -Lh
| 10***06 | Screw-Pan Head; (6-19x0.37-In) | 2 |
| 14***58 | Switch As-Start; (Key)(Ignition) | 1 |
| 15***94 | Panel | 1 |
216-4713 Gauge & Warning Gp -Rh
| 08***77 | Lamp Group-Dome; (12-Volt) | 1 |
| 10***06 | Screw-Pan Head; (6-19x0.37-In) | 2 |
| 15***97 | Panel | 1 |
233-5632 Guard Gp-Rops/Fops
| 15***61 | Plate As-Fops | 1 |
| 23***32 | Guard Group-Rops/Fops | 1 |
| 23***33 | Film; (Stripe, Lh) | 1 |
218-6400 Handhold Gp
| 21***77 | Handle | 1 |
| 21***00 | Handhold Group | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 2 |
298-7197 Handle Gp
| 28***14 | Handle | 1 |
| 29***37 | Nut | 1 |
| 29***38 | Seal | 1 |
218-6392 Heater & Mtg Gp-Cab
| 21***92 | Heater & Mtg Group-Cab | 1 |
| 21***93 | Heater Group-Cab | 1 |
| 21***02 | Insulation As | 1 |
218-6951 Heater Ar-Cab
| 21***19 | Lines Group-Heater | 1 |
| 21***92 | Heater & Mtg Group-Cab | 1 |
| 21***94 | Duct Group-Cab Air | 1 |
218-6393 Heater Gp-Cab
| 18***15 | Clip | 10 |
| 20***98 | Knob-Control; (Temperature Select) | 1 |
| 21***93 | Heater Group-Cab | 1 |
218-6746 Heater Gp-Cab -Kit
| 00***10 | Elbow | 1 |
| 13***53 | Hose; (192.5cm) (X2) | 0 |
| 14***71 | Louver As | 6 |
245-6811 Holder-Cup
| 24***11 | Holder-Cup | 1 |
230-3742 Horn Gp-Electric
| 11***90 | Fuse; (10 Amp) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***25 | Horn As; (24-Volt, Low Tone) | 1 |
231-8122 Housing As-Side -Air Conditioner, Heater
| 12***78 | Locknut; (M6x1-Thd) | 2 |
| 13***40 | Locknut; (M8x1.25-Thd) | 4 |
| 23***22 | Housing As-Side; -Air Conditioner, Heater | 1 |
218-6851 Installation Gp-Cover & Lines
| 21***18 | Cover Group-Console; -With Air Conditioner, Heater | 1 |
| 21***19 | Cover Group-Console; -Without Air Conditioner, Heater | 1 |
| 21***75 | Lines Group-Hydraulic Fan | 1 |
218-6747 Kit-Air Cond & Heater Instl
| 00***10 | Elbow | 1 |
| 08***91 | Bolt; (M10x1.5x55-mm) | 2 |
| 10***74 | Seal-Connector | 2 |
218-6749 Kit-Air Conditioner Instl
| 08***91 | Bolt; (M10x1.5x55-mm) | 2 |
| 10***74 | Seal-Connector | 2 |
| 10***96 | Clip | 2 |
218-6743 Kit-Cab Door & Mounting -Polycarbonate
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
218-6744 Kit-Cab Door & Mounting -Glass
| 09***25 | Pin-Clevis | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***15 | Connector | 1 |
218-6748 Kit-Cab Seal -Debris Barrier
| 12***43 | Seal; (70-cm) | 0 |
| 18***11 | Plate As | 1 |
| 18***12 | Plate | 1 |
234-0774 Lever Gp-Governor
| 12***78 | Locknut; (M6x1-Thd) | 2 |
| 19***63 | Lever Group-Hand Control; (Governor) | 1 |
| 23***32 | Cable As | 1 |
218-6356 Liner Gp-Cab
| 21***56 | Liner Group-Cab | 1 |
| 21***57 | Insulation | 1 |
| 21***59 | Liner-Rear Wall | 1 |
142-9311 Liner-Cab
| 14***11 | Liner-Cab; -Gray | 1 |
218-5680 Lines Gp-Air Conditioner
| 08***91 | Bolt; (M10x1.5x55-mm) | 2 |
| 10***96 | Clip | 2 |
| 18***90 | Accumulator Group-Refrigerant; -With Desiccant | 1 |
218-5619 Lines Gp-Heater
| 00***10 | Elbow | 1 |
| 13***53 | Hose; (192.5cm) (X2) | 0 |
| 17***20 | Strap-Dual Clamp | 1 |
6v-1970 Literature Gp
| 5P***58 | Sleeve; (Cable Splice) | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
| 6V***70 | Literature Group; (Literature Compartment) | 1 |
218-6395 Mirror Gp-Rear View
| 21***84 | Mirror As | 1 |
| 21***95 | Mirror Group-Rear View | 1 |
| 3B***05 | Washer,Lock Tube Assembly Mounting; Used On Engine P/N 5r698 | 1 |
223-6537 Module Gp-Warning Indicator
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 10 |
| 22***37 | Module Group-Warning Indicator | 1 |
229-7224 Module Gp-Warning Indicator -12-Volt
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 9 |
249-2910 Module Gp-Warning Indicator
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 9 |
| 23***06 | Gasket | 1 |
330-5012 Motor Gp-Window Wiper
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 4 |
| 26***23 | Cap-Wiper | 1 |
218-6370 Mounting Gp-Rops
| 15***78 | Mount As | 2 |
| 15***81 | Mount | 2 |
| 15***90 | Bracket | 1 |
218-5791 Panel Ar-Instrument
| 21***51 | Panel Group-Instrument; -Eame | 1 |
| 21***91 | Panel Ar-Instrument; -Eame | 1 |
218-5790 Panel Ar-Instrument
| 21***90 | Panel Ar-Instrument; -Nacd | 1 |
| 22***98 | Panel Group-Instrument; -Nacd | 1 |
225-7998 Panel Gp-Instrument
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 44 |
| 09***34 | Terminal-Blade; (18-Ga To 22-Ga) | 3 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
216-4751 Panel Gp-Instrument
| 09***36 | Terminal-Blade; (18-Ga To 22-Ga) | 57 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
218-6429 Panel Gp-Side
| 13***43 | Bolt-Round Head; (M6x1-6g-Thd) | 5 |
| 19***85 | Plate; (Rh) | 1 |
| 21***29 | Panel Group-Side | 1 |
218-6430 Panel Gp-Side
| 13***43 | Bolt-Round Head; (M6x1-6g-Thd) | 5 |
| 19***85 | Plate; (Rh) | 1 |
| 21***23 | Plate; (Lh) | 1 |
218-5565 Pedal Gp-Governor -Includes Lever
| 21***65 | Pedal Group-Governor; -Includes Lever | 1 |
| 21***66 | Cable Group-Governor Control | 1 |
| 23***74 | Lever Group-Governor | 1 |
325-8382 Pedal Gp-Governor
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 4 |
| 12***78 | Locknut; (M6x1-Thd) | 1 |
| 16***54 | Kit-Service; (Pedal) | 1 |
218-6390 Platform Gp-Operator
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 1 |
| 12***43 | Seal; (70-cm) | 0 |
| 21***61 | Plate As | 1 |
218-6406 Seal Gp-Cab
| 12***43 | Seal; (70-cm) | 0 |
| 18***11 | Plate As | 1 |
| 18***12 | Plate | 1 |
218-6664 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 21***64 | Seat Belt Group | 1 |
| 6E***49 | Washer; (11x27x6-mm Thk) | 2 |
276-6020 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 27***20 | Seat Belt Group | 1 |
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
218-6653 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 21***53 | Seat Belt Group | 1 |
| 6E***49 | Washer; (11x27x6-mm Thk) | 2 |
276-7277 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 27***77 | Seat Belt Group | 1 |
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
276-7276 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 27***76 | Seat Belt Group; -Suspension | 1 |
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
218-6654 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 21***54 | Seat Belt Group | 1 |
| 6E***49 | Washer; (11x27x6-mm Thk) | 2 |
276-6019 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 27***19 | Seat Belt Group | 1 |
| 2D***12 | Washer; (7/16x15/16x1/4-In Thk) | 2 |
218-6663 Seat Belt Gp
| 0T***44 | Bolt (1.25" Long) | 2 |
| 21***63 | Seat Belt Group | 1 |
| 6E***49 | Washer; (11x27x6-mm Thk) | 2 |
142-9305 Seat Gp -Suspension
| 14***05 | Seat Group; -Suspension | 1 |
| 21***80 | Seat Group-Adjustable | 1 |
| 5C***61 | Nut (M8x1.25 Thd); (M8x1.25 Thd) | 4 |
218-5562 Seat Gp -Static
| 15***60 | Switch; (Seat) | 1 |
| 15***85 | Wire As | 1 |
| 21***62 | Seat Group; -Static | 1 |
219-4380 Seat Gp-Adjustable
| 15***85 | Wire As | 1 |
| 15***86 | Switch As; (Seat) | 1 |
| 15***11 | Kit-Spring; (Adjustable Seat) | 1 |
218-6380 Spring Gp-Gas -Cab, Door
| 09***25 | Pin-Clevis | 1 |
| 15***82 | Spring-Gas; (Non-Locking) | 1 |
| 17***05 | Pin | 1 |
166-2569 Visor Gp-Cab
| 16***69 | Visor Group-Cab | 1 |
| 1D***77 | Bolt-Round Head; (3/8-16x1-In) | 2 |
| 2S***17 | Nut,Plain,Castellat; (3/8-16-Thd) | 1 |
173-3022 Visor Gp-Cab
| 16***62 | Plate As | 1 |
| 16***69 | Visor Group-Cab | 1 |
| 17***22 | Visor Group-Cab | 1 |
218-6745 Window Gp-Cab -Kit, Side
| 21***45 | Window Group-Cab; -Kit, Side | 1 |
| 22***57 | Window Group-Cab; -Upper,Lh | 1 |
| 22***58 | Window Group-Cab; -Upper, Rh | 1 |
218-6411 Window Gp-Cab -Side
| 21***11 | Window Group-Cab; -Side | 1 |
| 22***57 | Window Group-Cab; -Upper,Lh | 1 |
| 22***58 | Window Group-Cab; -Upper, Rh | 1 |
195-6723 Window Gp-Cab
| 14***19 | Window; (Rear) | 1 |
| 19***68 | Insulation | 1 |
| 19***23 | Window Group-Cab; -Rear | 1 |
224-7057 Window Gp-Cab -Upper,Lh
| 20***39 | Seal; (138-cm) | 0 |
| 20***73 | Seal; (220-cm) | 0 |
| 22***57 | Window Group-Cab; -Upper,Lh | 1 |
224-7058 Window Gp-Cab -Upper, Rh
| 20***39 | Seal; (138-cm) | 0 |
| 20***73 | Seal; (220-cm) | 0 |
| 22***58 | Window Group-Cab; -Upper, Rh | 1 |
Power Train
258-2859 Axle Gp
| 14***24 | Spindle-Wheel | 1 |
| 14***29 | Spacer; (57.16x69.85x27.54-mm Thk) | 1 |
| 15***52 | Seal-Lip Type | 1 |
142-9058 Axle Gp
| 14***23 | Housing-Axle | 1 |
| 14***24 | Spindle-Wheel | 1 |
| 14***29 | Spacer; (57.16x69.85x27.54-mm Thk) | 1 |
261-6285 Axle Gp
| 25***59 | Axle Group | 4 |
| 26***85 | Axle Group | 1 |
261-6275 Axle Gp
| 14***58 | Axle Group | 4 |
| 26***75 | Axle Group | 1 |
218-5609 Drive Control Ar-Hydrostatic
| 19***80 | Motor & Mtg Group-Hydrostatic | 1 |
| 21***28 | Pump & Mtg Group-Hydrostatic | 1 |
| 21***09 | Drive Control Ar-Hydrostatic | 1 |
218-5614 Drive Control Ar-Hydrostatic
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***31 | Jumper As; (2-Speed) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
218-5606 Drive Control Ar-Hydrostatic
| 19***80 | Motor & Mtg Group-Hydrostatic | 1 |
| 21***28 | Pump & Mtg Group-Hydrostatic | 1 |
| 21***06 | Drive Control Ar-Hydrostatic | 1 |
218-5608 Drive Control Ar-Hydrostatic
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***31 | Jumper As; (2-Speed) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
191-9760 Drive Gp-Tandem
| 10***66 | Bolt; (Self Locking) (M16x2x40mm) | 4 |
| 14***32 | Sprocket; (13-Teeth)(Motor) | 4 |
| 14***33 | Retainer | 2 |
142-9060 Drive Gp-Tandem
| 10***66 | Bolt; (Self Locking) (M16x2x40mm) | 4 |
| 14***32 | Sprocket; (13-Teeth)(Motor) | 4 |
| 14***33 | Retainer | 2 |
218-5624 Filter & Lines Gp-Hydraulic
| 14***15 | Connector As | 1 |
| 14***28 | Connector Assem. | 1 |
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 1 |
218-5980 Filter & Lines Gp-Hydraulic
| 14***15 | Connector As | 1 |
| 14***28 | Connector Assem. | 1 |
| 14***40 | Adapter; (Straight) (-8 Orb X -8 Orfs) | 1 |
223-9974 Filter Gp-Oil -Hydraulic
| 13***04 | Switch As-Pressure; (Power Train Oil Filter Bypass) | 1 |
| 1G***78 | Filter As-Oil; (Advanced Efficiency)(Hydraulic) | 1 |
| 22***74 | Filter Group-Oil; -Hydraulic | 1 |
218-5621 Lines Gp-Hydrostatic
| 14***41 | Hose As | 2 |
| 14***27 | Connector Group | 8 |
| 16***67 | Fitting As; (Quick Disconnect, Male)(Quick Disconnect) | 3 |
218-5636 Manifold & Lines Gp-Control -Parking Brake, 2-Speed
| 10***30 | Hose Assem. | 2 |
| 14***26 | Adapter; (Straight) (-4 Orb X -4 Orfs) | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 5 |
218-5635 Manifold & Lines Gp-Control -Parking Brake
| 10***30 | Hose Assem. | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 3 |
| 14***35 | Tee, -6 Orb / Orfs | 1 |
208-5681 Manifold & Solenoid Gp-Control -Parking Brake
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 1 |
| 20***81 | Manifold & Solenoid Group-Control; -Parking Brake | 1 |
| 21***61 | Flange | 1 |
245-6094 Manifold & Solenoid Gp-Control
| 09***74 | Bolt-Socket Head; (M5x0.8x12-mm) | 2 |
| 21***10 | Valve Group-Solenoid | 1 |
| 24***94 | Manifold & Solenoid Group-Control | 1 |
233-7131 Manifold & Solenoid Gp-Control -Parking Brake
| 09***68 | Bolt-Socket Head; (M5x0.8x8-mm) | 2 |
| 23***31 | Manifold & Solenoid Group-Control; -Parking Brake | 1 |
| 24***62 | Valve Group-Solenoid; (Parking Brake) | 1 |
259-8210 Manifold & Solenoid Gp-Control
| 09***68 | Bolt-Socket Head; (M5x0.8x8-mm) | 2 |
| 25***30 | Kit-Seal; (Valve) | 1 |
| 25***10 | Manifold & Solenoid Group-Control | 1 |
293-6591 Manifold & Solenoid Gp-Control -Parking Brake, 2-Speed
| 29***91 | Manifold & Solenoid Group-Control; -Parking Brake, 2-Speed | 1 |
222-3692 Manifold & Solenoid Gp-Control -Parking Brake, 2-Speed
| 19***00 | Valve Group-Solenoid; -12-Volt-Work Tool | 1 |
| 21***61 | Flange | 1 |
| 21***10 | Valve Group-Solenoid | 1 |
218-5560 Manifold Gp-Return
| 10***93 | Poppet | 1 |
| 14***18 | Connector As | 1 |
| 14***27 | Connector Group | 2 |
308-0421 Manifold Gp-Return
| 10***93 | Poppet | 1 |
| 14***18 | Connector As | 1 |
| 14***27 | Connector Group | 2 |
191-9780 Motor & Mtg Gp-Hydrostatic
| 19***80 | Motor & Mtg Group-Hydrostatic | 1 |
| 19***40 | Bolt-Carriage; (M16x2x65-mm) | 16 |
| 28***56 | Motor Group-Piston; -Hydrostatic | 2 |
190-7457 Motor & Mtg Gp-Hydrostatic
| 19***57 | Motor & Mtg Group-Hydrostatic; -2-Speed | 1 |
| 19***40 | Bolt-Carriage; (M16x2x65-mm) | 16 |
| 28***58 | Motor Group-Piston; -Hydrostatic | 2 |
280-7856 Motor Gp-Piston -Hydrostatic
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 14***13 | Shim; (0.01-mm Thk) | 1 |
220-8172 Motor Gp-Piston
| 09***01 | Bolt-Socket Head; (M8x1.25x40-mm) | 2 |
| 14***13 | Shim; (0.01-mm Thk) | 1 |
| 14***14 | Shim; (0.3-mm Thk) | 1 |
280-7858 Motor Gp-Piston -Hydrostatic
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 1 |
| 14***13 | Shim; (0.01-mm Thk) | 1 |
220-8162 Motor Gp-Piston
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 14***13 | Shim; (0.01-mm Thk) | 1 |
| 14***14 | Shim; (0.3-mm Thk) | 2 |
218-0918 Mounting Gp-Pump
| 14***19 | Plate-Adapter | 1 |
| 21***18 | Mounting Group-Pump | 1 |
| 22***35 | Flange | 1 |
218-5600 Power Train Ar
| 14***60 | Drive Group-Tandem; -Work Tool | 1 |
| 21***00 | Power Train Ar | 1 |
218-5800 Power Train Ar
| 19***60 | Drive Group-Tandem | 1 |
| 21***00 | Power Train Ar | 1 |
218-5928 Pump & Mtg Gp-Hydrostatic
| 09***94 | Ring-Retaining | 1 |
| 16***42 | Washer-Hard; (14.8x27x3-mm Thk) | 2 |
| 16***39 | Bolt; (M14x2x40-mm) | 2 |
218-0928 Pump & Mtg Gp-Hydrostatic
| 09***94 | Ring-Retaining | 1 |
| 16***42 | Washer-Hard; (14.8x27x3-mm Thk) | 2 |
| 16***39 | Bolt; (M14x2x40-mm) | 2 |
191-9617 Pump Gp-Piston
| 10***09 | Bearing | 2 |
| 10***65 | Circlip | 2 |
| 12***59 | Bearing-Roller | 2 |
191-9700 Pump Gp-Piston
| 08***98 | Bearing | 2 |
| 10***65 | Circlip | 2 |
| 12***59 | Bearing-Roller | 2 |
307-3070 Pump Gp-Piston
| 08***98 | Bearing | 1 |
| 10***65 | Circlip | 2 |
| 12***59 | Bearing-Roller | 2 |
289-6359 Pump Gp-Piston -Hydrostatic
| 08***98 | Bearing | 2 |
| 10***65 | Circlip | 2 |
| 12***59 | Bearing-Roller | 2 |
289-6351 Pump Gp-Piston -Hydrostatic
| 08***98 | Bearing | 2 |
| 10***65 | Circlip | 2 |
| 12***59 | Bearing-Roller | 2 |
228-9221 Tire & Rim Gp
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***69 | Tire; (12-R16.5) | 1 |
165-4907 Tire & Rim Gp -Heavy-Duty, Rh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 16***07 | Tire & Rim Group; -Heavy-Duty, Rh | 1 |
185-9931 Tire & Rim Gp -Rh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***31 | Tire & Rim Group; -Rh | 1 |
185-9930 Tire & Rim Gp -Lh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***30 | Tire & Rim Group; -Lh | 1 |
154-3980 Tire & Rim Gp
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 15***80 | Tire & Rim Group; -Lh | 1 |
185-8675 Tire & Rim Gp -Rh
| 15***99 | Valve As-Tire | 1 |
| 18***75 | Tire & Rim Group; -Rh | 1 |
| 18***35 | Tire; (305-546) | 1 |
154-3979 Tire & Rim Gp -Rh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 15***79 | Tire & Rim Group; -Rh | 1 |
185-8676 Tire & Rim Gp -Lh
| 15***99 | Valve As-Tire | 1 |
| 18***76 | Tire & Rim Group; -Lh | 1 |
| 18***35 | Tire; (305-546) | 1 |
185-9929 Tire & Rim Gp -Rh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***29 | Tire & Rim Group; -Rh | 1 |
165-4902 Tire & Rim Gp -Heavy-Duty, Rh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 16***02 | Tire & Rim Group; -Heavy-Duty, Rh | 1 |
188-0124 Tire & Rim Gp -Lh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***33 | Tire; (12-16.5) | 1 |
265-2901 Tire & Rim Gp -Rh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***63 | Tire; (12-16.5) | 1 |
265-2898 Tire & Rim Gp -Lh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***63 | Tire; (12-16.5) | 1 |
185-9928 Tire & Rim Gp -Lh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***28 | Tire & Rim Group; -Lh | 1 |
265-2900 Tire & Rim Gp -Lh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***63 | Tire; (12-16.5) | 1 |
228-9220 Tire & Rim Gp
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***69 | Tire; (12-R16.5) | 1 |
265-2899 Tire & Rim Gp -Rh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 22***63 | Tire; (12-16.5) | 1 |
185-8677 Tire & Rim Gp -Rh
| 15***99 | Valve As-Tire | 1 |
| 18***77 | Tire & Rim Group; -Rh | 1 |
| 18***35 | Tire; (305-546) | 1 |
188-0125 Tire & Rim Gp -Rh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 18***33 | Tire; (12-16.5) | 1 |
185-8674 Tire & Rim Gp -Lh
| 15***99 | Valve As-Tire | 1 |
| 18***74 | Tire & Rim Group; -Lh | 1 |
| 18***35 | Tire; (305-546) | 1 |
154-3981 Tire & Rim Gp
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 15***81 | Tire & Rim Group; -Rh | 1 |
154-3978 Tire & Rim Gp -Lh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 15***78 | Tire & Rim Group; -Lh | 1 |
165-4906 Tire & Rim Gp -Heavy-Duty, Lh
| 14***59 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 16***06 | Tire & Rim Group; -Heavy-Duty, Lh | 1 |
165-4901 Tire & Rim Gp -Heavy-Duty, Lh
| 14***31 | Wheel As | 1 |
| 15***99 | Valve As-Tire | 1 |
| 16***01 | Tire & Rim Group; -Heavy-Duty, Lh | 1 |
259-8194 Valve Gp-Solenoid
| 23***26 | Coil As | 1 |
| 25***94 | Valve Group-Solenoid; -Parking Brake | 1 |
228-9219 Wheel & Tire Ar
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 22***19 | Wheel & Tire Ar | 1 |
| 22***21 | Tire & Rim Group | 4 |
252-0347 Wheel & Tire Ar
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 25***47 | Wheel & Tire Ar | 1 |
| 26***00 | Tire & Rim Group; -Lh | 2 |
185-8663 Wheel & Tire Ar -Low Side Wall
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 18***63 | Wheel & Tire Ar; -Low Side Wall | 1 |
| 18***76 | Tire & Rim Group; -Lh | 2 |
252-0366 Wheel & Tire Ar -Solid
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 22***34 | Tire-Solid; (33x6x11)(Rh) | 2 |
| 22***35 | Tire-Solid; (33x6x11)(Rh) | 2 |
185-8666 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 18***66 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 18***28 | Tire & Rim Group; -Lh | 2 |
154-3973 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 15***73 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 15***80 | Tire & Rim Group; -Lh | 2 |
185-8667 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 18***67 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 18***30 | Tire & Rim Group; -Lh | 2 |
165-4903 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 16***03 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 16***06 | Tire & Rim Group; -Heavy-Duty, Lh | 2 |
159-5761 Wheel & Tire Ar -Solid
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 15***61 | Wheel & Tire Ar; -Solid | 1 |
| 18***30 | Tire-Solid; (33x6x8) | 4 |
228-9217 Wheel & Tire Ar
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 22***17 | Wheel & Tire Ar | 1 |
| 22***20 | Tire & Rim Group | 4 |
252-0346 Wheel & Tire Ar
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 25***46 | Wheel & Tire Ar | 1 |
| 26***98 | Tire & Rim Group; -Lh | 2 |
165-4898 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 16***98 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 16***01 | Tire & Rim Group; -Heavy-Duty, Lh | 2 |
154-3972 Wheel & Tire Ar -Heavy Duty
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 15***72 | Wheel & Tire Ar; -Heavy Duty | 1 |
| 15***78 | Tire & Rim Group; -Lh | 2 |
185-8662 Wheel & Tire Ar -Low Side Wall
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 18***62 | Wheel & Tire Ar; -Low Side Wall | 1 |
| 18***74 | Tire & Rim Group; -Lh | 2 |
252-0377 Wheel & Tire Ar -Solid
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 22***34 | Tire-Solid; (33x6x11)(Rh) | 2 |
| 22***35 | Tire-Solid; (33x6x11)(Rh) | 2 |
187-3239 Wheel & Tire Ar
| 14***93 | Nut-Lug; (9/16-18-2b-Thd) | 32 |
| 18***39 | Wheel & Tire Ar | 1 |
| 18***24 | Tire & Rim Group; -Lh | 2 |
259-9892 Wheel & Tire Gp
| 22***34 | Tire-Solid; (33x6x11)(Rh) | 2 |
| 22***35 | Tire-Solid; (33x6x11)(Rh) | 2 |
| 25***92 | Wheel & Tire Group | 1 |
Service Equipment And Supplies
218-6255 Film Gp
| 12***10 | Film; (Red Stripe)(Red Stripe - 1225 cm) | 0 |
| 16***89 | Film; (Caterpillar) | 1 |
| 21***55 | Film Group | 1 |
238-7734 Film Gp -Un
| 23***34 | Film Group; -Un | 1 |
| 25***15 | Film-Identification; (Un)(Front) | 1 |
| 25***16 | Film-Identification; (Un)(Side) | 2 |
218-6846 Film Gp -Kit
| 12***10 | Film; (Red Stripe)(Red Stripe - 1225 cm) | 0 |
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 16***89 | Film; (Caterpillar) | 1 |
218-6259 Film Gp
| 12***10 | Film; (Red Stripe)(Red Stripe - 1225 cm) | 0 |
| 16***89 | Film; (Caterpillar) | 1 |
| 21***59 | Film Group | 1 |
218-6843 Film Gp
| 12***10 | Film; (Red Stripe)(Red Stripe - 1225 cm) | 0 |
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 16***89 | Film; (Caterpillar) | 1 |
191-9684 Film Gp -Clearance
| 16***00 | Film-Warning; (Clearance) | 1 |
| 19***84 | Film Group; -Clearance | 1 |
218-6292 Plate & Film Gp
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
218-5911 Plate & Film Gp
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
286-9251 Plate & Film Gp
| 16***89 | Tack-Fastener | 4 |
| 22***69 | Film-Warning; (Do Not Operate, Read Omm) | 1 |
| 24***18 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
195-6740 Plate & Film Gp
| 19***40 | Plate & Film Group | 1 |
| 19***10 | Film-Identification; (Synthetic Hydraulic Oil, Read Omm) | 1 |
218-6291 Plate & Film Gp
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
218-5951 Plate & Film Gp
| 15***62 | Film-Information; (Tie-Down Location) | 4 |
| 15***53 | Film-Information; (Read Omm) | 1 |
| 16***76 | Film; (Identification) (12v) (On Rear Console Behind Operators Seat) | 1 |
Work Tools
216-8756 Arm Gp-Material Handling
| 15***62 | Film-Information; (Tie-Down Location) | 2 |
| 18***33 | Step Group-Material Handling Arm | 1 |
| 21***56 | Arm Group-Material Handling | 1 |
177-1990 Blade Ar -Angling
| 14***41 | Edge Group-Cutting | 1 |
| 17***82 | Blade Group-Angling | 1 |
| 17***83 | Spring Group-Blade | 1 |
177-1989 Blade Ar -Angling
| 13***86 | Edge Group-Cutting | 1 |
| 17***81 | Blade Group-Angling | 1 |
| 17***83 | Spring Group-Blade | 1 |
177-1982 Blade Gp-Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***40 | Pin | 2 |
| 16***19 | Pin As | 2 |
177-1981 Blade Gp-Angling
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***40 | Pin | 2 |
| 16***19 | Pin As | 2 |
279-5387 Blade Gp-Multipurpose Bucket
| 15***59 | Edge | 1 |
| 27***87 | Blade Group-Multipurpose Bucket | 1 |
325-7078 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 32***78 | Blade Group-Multipurpose Bucket | 1 |
279-5385 Blade Gp-Multipurpose Bucket
| 15***37 | Edge | 1 |
| 27***85 | Blade Group-Multipurpose Bucket | 1 |
279-5395 Blade Gp-Multipurpose Bucket
| 15***77 | Edge | 1 |
| 27***95 | Blade Group-Multipurpose Bucket | 1 |
154-5080 Blade Gp-Multipurpose Bucket
| 15***77 | Edge | 1 |
| 15***80 | Blade Group-Multipurpose Bucket | 1 |
279-5396 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***95 | Blade Group-Multipurpose Bucket | 1 |
325-7068 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 32***68 | Blade Group-Multipurpose Bucket | 1 |
325-7059 Blade Gp-Multipurpose Bucket
| 15***77 | Edge | 1 |
| 32***54 | Guard As; (72-In) | 1 |
| 32***59 | Blade Group-Multipurpose Bucket | 1 |
325-7038 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 32***38 | Blade Group-Multipurpose Bucket, Protective Cover | 1 |
325-7069 Blade Gp-Multipurpose Bucket
| 19***16 | Edge | 1 |
| 32***64 | Guard As; (78-In) | 1 |
| 32***69 | Blade Group-Multipurpose Bucket | 1 |
325-7048 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 32***48 | Blade Group-Multipurpose Bucket | 1 |
159-5347 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***80 | Blade Group-Multipurpose Bucket | 1 |
| 15***47 | Blade Group-Multipurpose Bucket | 1 |
325-7058 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 32***58 | Blade Group-Multipurpose Bucket | 1 |
279-5405 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***05 | Blade Group-Multipurpose Bucket | 1 |
325-7039 Blade Gp-Multipurpose Bucket
| 15***37 | Edge | 1 |
| 32***34 | Guard As; (60-In) | 1 |
| 32***39 | Blade Group-Multipurpose Bucket | 1 |
325-7079 Blade Gp-Multipurpose Bucket
| 29***44 | Edge | 1 |
| 32***74 | Guard As; (84-In) | 1 |
| 32***79 | Blade Group-Multipurpose Bucket | 1 |
325-7049 Blade Gp-Multipurpose Bucket
| 15***59 | Edge | 1 |
| 32***44 | Guard As; (66-In) | 1 |
| 32***49 | Blade Group-Multipurpose Bucket | 1 |
159-5345 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***45 | Blade Group-Multipurpose Bucket | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5406 Blade Gp-Multipurpose Bucket
| 19***16 | Edge | 1 |
| 27***06 | Blade Group-Multipurpose Bucket | 1 |
279-5388 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***87 | Blade Group-Multipurpose Bucket | 1 |
279-5384 Blade Gp-Multipurpose Bucket
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***84 | Blade Group-Multipurpose Bucket | 1 |
279-5435 Bucket Ar-Dirt
| 13***83 | Edge Group-Cutting | 1 |
| 27***34 | Bucket As-Dirt | 1 |
| 27***35 | Bucket Ar-Dirt | 1 |
268-4083 Bucket Ar-Dirt
| 13***87 | Edge Group-Cutting | 1 |
| 26***83 | Bucket Ar-Dirt | 1 |
| 26***84 | Bucket Group-Dirt | 1 |
285-6090 Bucket Ar-Dirt
| 13***86 | Edge Group-Cutting | 1 |
| 28***89 | Bucket As-Dirt | 1 |
| 28***90 | Bucket Ar-Dirt, Turbocharger | 1 |
279-5438 Bucket Ar-Dirt
| 13***84 | Edge Group-Cutting | 1 |
| 27***37 | Bucket As-Dirt | 1 |
| 27***38 | Bucket Ar-Dirt | 1 |
279-5441 Bucket Ar-Dirt
| 13***85 | Edge Group-Cutting | 1 |
| 27***40 | Bucket As-Dirt | 1 |
| 27***41 | Bucket Ar-Dirt | 1 |
229-3426 Bucket Ar-General Purpose
| 14***99 | Tooth Group-Uni | 9 |
| 22***26 | Bucket Ar-General Purpose | 1 |
| 22***27 | Bucket As-General Purpose | 1 |
279-5369 Bucket Ar-General Purpose
| 13***85 | Edge Group-Cutting | 1 |
| 27***68 | Bucket As-General Purpose | 1 |
| 27***69 | Bucket Ar-General Purpose | 1 |
279-5378 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5374 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5366 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5370 Bucket Ar-General Purpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5377 Bucket Ar-General Purpose
| 13***87 | Edge Group-Cutting | 1 |
| 27***76 | Bucket As-General Purpose | 1 |
| 27***77 | Bucket Ar-General Purpose | 1 |
279-5373 Bucket Ar-General Purpose
| 13***86 | Edge Group-Cutting | 1 |
| 27***72 | Bucket As-General Purpose | 1 |
| 27***73 | Bucket Ar-General Purpose | 1 |
279-5365 Bucket Ar-General Purpose
| 13***84 | Edge Group-Cutting | 1 |
| 27***64 | Bucket As-General Purpose | 1 |
| 27***65 | Bucket Ar-General Purpose | 1 |
285-6111 Bucket Ar-Grapple
| 28***00 | Bucket Ar-Utility | 1 |
| 28***11 | Bucket Ar-Grapple | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
157-7224 Bucket Ar-Grapple
| 15***85 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***12 | Cylinder Group-Grapple | 2 |
157-7226 Bucket Ar-Grapple
| 13***84 | Edge Group-Cutting | 1 |
| 15***23 | Bucket Ar-Grapple | 1 |
| 15***26 | Bucket Ar-Grapple; -Industrial | 1 |
285-6093 Bucket Ar-Grapple
| 28***93 | Bucket Ar-Grapple | 1 |
| 28***99 | Bucket Group-Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
217-6230 Bucket Ar-Grapple
| 13***87 | Edge Group-Cutting | 1 |
| 21***29 | Bucket Ar-Grapple | 1 |
| 21***30 | Bucket Ar-Grapple | 1 |
165-8780 Bucket Ar-Grapple -Utility
| 16***34 | Grapple & Cylinder Group-Utility | 1 |
| 16***78 | Bucket Group-Utility | 1 |
| 16***80 | Bucket Ar-Grapple; -Utility | 1 |
165-8779 Bucket Ar-Grapple
| 16***34 | Grapple & Cylinder Group-Utility | 1 |
| 16***77 | Bucket Group-Utility | 1 |
| 16***79 | Bucket Ar-Grapple | 1 |
217-6229 Bucket Ar-Grapple
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
| 21***28 | Bucket Group-Grapple | 1 |
285-6112 Bucket Ar-Grapple
| 28***01 | Bucket Ar-Utility | 1 |
| 28***12 | Bucket Ar-Grapple | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
286-9301 Bucket Ar-Grapple
| 28***44 | Bucket Group-Grapple | 1 |
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
| 28***50 | Lines Group-Grapple | 1 |
157-7223 Bucket Ar-Grapple
| 15***84 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***12 | Cylinder Group-Grapple | 2 |
157-7225 Bucket Ar-Grapple -Industrial
| 15***86 | Bucket Group-Grapple; -Industrial | 1 |
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***12 | Cylinder Group-Grapple | 2 |
158-6095 Bucket Ar-Grapple
| 13***86 | Edge Group-Cutting | 1 |
| 15***25 | Bucket Ar-Grapple; -Industrial | 1 |
| 15***95 | Bucket Ar-Grapple; -Industrial | 1 |
285-6104 Bucket Ar-Grapple
| 28***02 | Bucket Group-Utility | 1 |
| 28***04 | Bucket Ar-Grapple | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
286-9300 Bucket Ar-Grapple
| 28***48 | Mounting Group-Cylinder; -Grapple Bucket | 1 |
| 28***51 | Plate & Film Group | 1 |
| 28***78 | Bucket Group-Grapple | 1 |
157-7227 Bucket Ar-Grapple
| 13***85 | Edge Group-Cutting | 1 |
| 15***24 | Bucket Ar-Grapple | 1 |
| 15***27 | Bucket Ar-Grapple; -Industrial | 1 |
279-5425 Bucket Ar-Light Material
| 13***87 | Edge Group-Cutting | 1 |
| 27***24 | Bucket As-Light Material | 1 |
| 27***25 | Bucket Ar-Light Material | 1 |
279-5430 Bucket Ar-Light Material
| 19***24 | Edge Group-Cutting | 1 |
| 27***29 | Bucket As-Light Material | 1 |
| 27***30 | Bucket Ar-Light Material | 1 |
279-5420 Bucket Ar-Light Material
| 13***86 | Edge Group-Cutting | 1 |
| 27***20 | Bucket Ar-Light Material | 1 |
| 27***21 | Bucket As-Light Material | 1 |
154-5048 Bucket Ar-Multipurpose
| 14***99 | Tooth Group-Uni | 8 |
| 15***08 | Bucket Ar-Multipurpose | 1 |
| 15***48 | Bucket Ar-Multipurpose | 1 |
199-8321 Bucket Ar-Multipurpose
| 13***87 | Edge Group-Cutting | 1 |
| 19***20 | Bucket Ar-Multipurpose | 1 |
| 19***21 | Bucket Ar-Multipurpose | 1 |
279-5391 Bucket Ar-Multipurpose
| 13***85 | Edge Group-Cutting | 1 |
| 27***90 | Bucket Ar-Multipurpose | 1 |
| 27***91 | Bucket Ar-Multipurpose | 1 |
325-7066 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
325-7055 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5403 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***18 | Cylinder Group-Bucket | 2 |
| 16***36 | Cover Group-Lines | 1 |
199-8320 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***18 | Cylinder Group-Bucket | 2 |
| 16***36 | Cover Group-Lines | 1 |
325-7040 Bucket Ar-Multipurpose
| 13***84 | Edge Group-Cutting | 1 |
| 32***36 | Bucket Ar-Multipurpose, Protective Cover | 1 |
| 32***40 | Bucket Ar-Multipurpose | 1 |
279-5401 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7070 Bucket Ar-Multipurpose
| 13***87 | Edge Group-Cutting | 1 |
| 32***66 | Bucket Ar-Multipurpose | 1 |
| 32***70 | Bucket Ar-Multipurpose | 1 |
154-5047 Bucket Ar-Multipurpose
| 13***85 | Edge Group-Cutting | 1 |
| 15***08 | Bucket Ar-Multipurpose | 1 |
| 15***47 | Bucket Ar-Multipurpose | 1 |
279-5400 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7045 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7046 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
279-5381 Bucket Ar-Multipurpose
| 13***84 | Edge Group-Cutting | 1 |
| 27***81 | Bucket Ar-Multipurpose | 1 |
| 27***82 | Bucket Ar-Multipurpose | 1 |
279-5392 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7035 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
154-5004 Bucket Ar-Multipurpose
| 15***04 | Bucket Ar-Multipurpose | 1 |
| 15***05 | Bucket Group-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
279-5390 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***18 | Cylinder Group-Bucket | 2 |
| 16***36 | Cover Group-Lines | 1 |
154-5049 Bucket Ar-Multipurpose
| 13***86 | Edge Group-Cutting | 1 |
| 15***10 | Bucket Ar-Multipurpose | 1 |
| 15***49 | Bucket Ar-Multipurpose | 1 |
325-7056 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
279-5398 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***18 | Cylinder Group-Bucket | 2 |
| 16***36 | Cover Group-Lines | 1 |
154-5010 Bucket Ar-Multipurpose
| 15***09 | Bucket Group-Multipurpose | 1 |
| 15***10 | Bucket Ar-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
325-7076 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
154-5008 Bucket Ar-Multipurpose
| 15***07 | Bucket Group-Multipurpose | 1 |
| 15***08 | Bucket Ar-Multipurpose | 1 |
| 15***11 | Mounting Group-Cylinder | 1 |
279-5380 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
325-7060 Bucket Ar-Multipurpose
| 13***86 | Edge Group-Cutting | 1 |
| 32***56 | Bucket Ar-Multipurpose | 1 |
| 32***60 | Bucket Ar-Multipurpose | 1 |
154-5046 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 8 |
| 15***04 | Bucket Ar-Multipurpose | 1 |
279-5399 Bucket Ar-Multipurpose
| 13***86 | Edge Group-Cutting | 1 |
| 27***98 | Bucket Ar-Multipurpose | 1 |
| 27***99 | Bucket Ar-Multipurpose | 1 |
325-7080 Bucket Ar-Multipurpose
| 19***24 | Edge Group-Cutting | 1 |
| 32***76 | Bucket Ar-Multipurpose | 1 |
| 32***80 | Bucket Ar-Multipurpose | 1 |
154-5045 Bucket Ar-Multipurpose
| 13***84 | Edge Group-Cutting | 1 |
| 15***04 | Bucket Ar-Multipurpose | 1 |
| 15***45 | Bucket Ar-Multipurpose | 1 |
325-7036 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 27***69 | Cylinder Group-Hydraulic | 2 |
325-7065 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
279-5402 Bucket Ar-Multipurpose
| 13***87 | Edge Group-Cutting | 1 |
| 27***02 | Bucket Ar-Multipurpose | 1 |
| 27***03 | Bucket Ar-Multipurpose | 1 |
154-5050 Bucket Ar-Multipurpose
| 14***99 | Tooth Group-Uni | 8 |
| 15***10 | Bucket Ar-Multipurpose | 1 |
| 15***50 | Bucket Ar-Multipurpose | 1 |
325-7050 Bucket Ar-Multipurpose
| 13***85 | Edge Group-Cutting | 1 |
| 32***46 | Bucket Ar-Multipurpose | 1 |
| 32***50 | Bucket Ar-Multipurpose | 1 |
279-5382 Bucket Ar-Multipurpose
| 15***11 | Mounting Group-Cylinder | 1 |
| 15***18 | Cylinder Group-Bucket | 2 |
| 16***36 | Cover Group-Lines | 1 |
325-7075 Bucket Ar-Multipurpose
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 9 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
199-8322 Bucket Ar-Multipurpose
| 14***99 | Tooth Group-Uni | 9 |
| 19***20 | Bucket Ar-Multipurpose | 1 |
| 19***22 | Bucket Ar-Multipurpose | 1 |
285-6100 Bucket Ar-Utility
| 13***85 | Edge Group-Cutting | 1 |
| 28***99 | Bucket Group-Utility | 1 |
| 28***00 | Bucket Ar-Utility | 1 |
285-6101 Bucket Ar-Utility
| 13***86 | Edge Group-Cutting | 1 |
| 28***01 | Bucket Ar-Utility | 1 |
| 28***02 | Bucket Group-Utility | 1 |
285-6095 Bucket Ar-Utility
| 13***84 | Edge Group-Cutting | 1 |
| 28***95 | Bucket Ar-Utility | 1 |
| 28***96 | Bucket Group-Utility | 1 |
152-0227 Bucket As-Dirt
| 14***35 | Edge | 1 |
| 15***27 | Bucket As-Dirt | 1 |
188-3526 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 18***16 | Bucket As-Dirt | 1 |
279-5439 Bucket As-Dirt
| 14***36 | Edge | 1 |
| 27***39 | Bucket As-Dirt | 1 |
285-6089 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***88 | Bucket As-Dirt | 1 |
285-6088 Bucket As-Dirt
| 14***37 | Edge | 1 |
| 28***88 | Bucket As-Dirt | 1 |
141-6704 Bucket As-Dirt
| 14***04 | Bucket As-Dirt | 1 |
| 14***36 | Edge | 1 |
165-6156 Bucket As-Dirt
| 15***27 | Bucket As-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***56 | Bucket As-Dirt | 1 |
165-6157 Bucket As-Dirt
| 14***04 | Bucket As-Dirt | 1 |
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***57 | Bucket As-Dirt | 1 |
188-2716 Bucket As-Dirt
| 14***37 | Edge | 1 |
| 18***16 | Bucket As-Dirt | 1 |
279-5436 Bucket As-Dirt
| 14***35 | Edge | 1 |
| 27***36 | Bucket As-Dirt | 1 |
279-5433 Bucket As-Dirt
| 14***34 | Edge | 1 |
| 27***33 | Bucket As-Dirt | 1 |
279-5437 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***36 | Bucket As-Dirt | 1 |
268-4089 Bucket As-Dirt
| 19***22 | Edge | 1 |
| 26***89 | Bucket As-Dirt | 1 |
279-5434 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***33 | Bucket As-Dirt | 1 |
279-5440 Bucket As-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***39 | Bucket As-Dirt | 1 |
279-5368 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***67 | Bucket As-General Purpose | 1 |
279-5376 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***75 | Bucket As-General Purpose | 1 |
229-3428 Bucket As-General Purpose
| 22***28 | Bucket As-General Purpose | 1 |
| 22***32 | Edge | 1 |
279-5363 Bucket As-General Purpose
| 14***35 | Edge | 1 |
| 27***63 | Bucket As-General Purpose | 1 |
279-5364 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***63 | Bucket As-General Purpose | 1 |
279-5372 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***71 | Bucket As-General Purpose | 1 |
279-5375 Bucket As-General Purpose
| 19***22 | Edge | 1 |
| 27***75 | Bucket As-General Purpose | 1 |
165-6154 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***54 | Bucket As-General Purpose | 1 |
| 16***89 | Tack-Fastener | 4 |
199-7720 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 19***20 | Bucket As-General Purpose | 1 |
279-5371 Bucket As-General Purpose
| 14***37 | Edge | 1 |
| 27***71 | Bucket As-General Purpose | 1 |
229-3427 Bucket As-General Purpose
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 22***27 | Bucket As-General Purpose | 1 |
279-5367 Bucket As-General Purpose
| 14***36 | Edge | 1 |
| 27***67 | Bucket As-General Purpose | 1 |
165-6153 Bucket As-General Purpose
| 14***36 | Edge | 1 |
| 16***53 | Bucket As-General Purpose | 1 |
156-0888 Bucket As-Grapple
| 14***36 | Edge | 1 |
| 15***88 | Bucket As-Grapple | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
169-8941 Bucket As-Grapple
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***87 | Bucket As-Grapple; -Industrial | 1 |
| 16***89 | Tack-Fastener | 4 |
217-6226 Bucket As-Grapple
| 16***30 | Plate-Identification; (Cat) | 2 |
| 19***22 | Edge | 1 |
| 21***26 | Bucket As-Grapple | 1 |
156-0887 Bucket As-Grapple
| 14***35 | Edge | 1 |
| 15***87 | Bucket As-Grapple; -Industrial | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
169-8942 Bucket As-Grapple
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***88 | Bucket As-Grapple | 1 |
| 16***89 | Tack-Fastener | 4 |
217-6227 Bucket As-Grapple
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 21***26 | Bucket As-Grapple | 1 |
169-8943 Bucket As-Grapple
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 15***89 | Bucket As-Grapple | 1 |
| 16***89 | Tack-Fastener | 4 |
156-0889 Bucket As-Grapple
| 14***37 | Edge | 1 |
| 15***89 | Bucket As-Grapple | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
279-5428 Bucket As-Light Material
| 22***82 | Edge | 1 |
| 27***28 | Bucket As-Light Material | 1 |
164-7414 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***14 | Bucket As-Light Material | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5421 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***21 | Bucket As-Light Material | 1 |
164-7415 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***15 | Bucket As-Light Material | 1 |
| 16***89 | Tack-Fastener | 4 |
279-5422 Bucket As-Light Material
| 14***37 | Edge | 1 |
| 27***22 | Bucket As-Light Material | 1 |
220-4991 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 22***91 | Bucket As-Light Material | 1 |
279-5429 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***28 | Bucket As-Light Material | 1 |
279-5424 Bucket As-Light Material
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 27***23 | Bucket As-Light Material | 1 |
279-5423 Bucket As-Light Material
| 19***22 | Edge | 1 |
| 27***23 | Bucket As-Light Material | 1 |
165-8832 Bucket As-Utility
| 11***83 | Boss; (M10x1.5-Thd) | 4 |
| 14***36 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
285-6103 Bucket As-Utility
| 14***37 | Edge | 1 |
| 28***03 | Bucket As-Utility | 1 |
285-6098 Bucket As-Utility
| 14***36 | Edge | 1 |
| 28***98 | Bucket As-Utility, Fuel Injection Pump; - Assembly | 1 |
165-8837 Bucket As-Utility
| 14***35 | Edge | 1 |
| 16***30 | Plate-Identification; (Cat) | 2 |
| 16***37 | Bucket As-Utility | 1 |
165-8835 Bucket As-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***35 | Bucket As-Utility | 1 |
| 16***37 | Bucket As-Utility | 1 |
165-8747 Bucket As-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***47 | Bucket As-Utility | 1 |
| 16***33 | Bucket As-Utility | 1 |
165-8746 Bucket As-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***46 | Bucket As-Utility | 1 |
| 16***32 | Bucket As-Utility | 1 |
285-6097 Bucket As-Utility
| 14***35 | Edge | 1 |
| 28***97 | Bucket As-Utility | 1 |
152-0232 Bucket Gp-Dirt
| 13***85 | Edge Group-Cutting | 1 |
| 15***32 | Bucket Group-Dirt | 1 |
| 16***57 | Bucket As-Dirt | 1 |
188-2719 Bucket Gp-Dirt
| 13***86 | Edge Group-Cutting | 1 |
| 18***19 | Bucket Group-Dirt | 1 |
| 18***26 | Bucket As-Dirt | 1 |
152-0231 Bucket Gp-Dirt
| 13***84 | Edge Group-Cutting | 1 |
| 15***31 | Bucket Group-Dirt | 1 |
| 16***56 | Bucket As-Dirt | 1 |
268-4084 Bucket Gp-Dirt
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 26***84 | Bucket Group-Dirt | 1 |
229-3433 Bucket Gp-General Purpose
| 19***24 | Edge Group-Cutting | 1 |
| 22***27 | Bucket As-General Purpose | 1 |
| 22***33 | Bucket Group-General Purpose | 1 |
199-7727 Bucket Gp-General Purpose
| 14***99 | Tooth Group-Uni | 9 |
| 19***20 | Bucket As-General Purpose | 1 |
| 19***27 | Bucket Group-General Purpose | 1 |
152-0226 Bucket Gp-General Purpose
| 13***85 | Edge Group-Cutting | 1 |
| 15***26 | Bucket Group-General Purpose | 1 |
| 16***53 | Bucket As-General Purpose | 1 |
152-0228 Bucket Gp-General Purpose
| 14***99 | Tooth Group-Uni | 8 |
| 15***28 | Bucket Group-General Purpose | 1 |
| 16***54 | Bucket As-General Purpose | 1 |
152-0225 Bucket Gp-General Purpose
| 14***99 | Tooth Group-Uni | 8 |
| 15***25 | Bucket Group-General Purpose | 1 |
| 16***53 | Bucket As-General Purpose | 1 |
199-7726 Bucket Gp-General Purpose
| 13***87 | Edge Group-Cutting | 1 |
| 19***20 | Bucket As-General Purpose | 1 |
| 19***26 | Bucket Group-General Purpose | 1 |
152-0229 Bucket Gp-General Purpose
| 13***86 | Edge Group-Cutting | 1 |
| 15***29 | Bucket Group-General Purpose | 1 |
| 16***54 | Bucket As-General Purpose | 1 |
156-0884 Bucket Gp-Grapple
| 15***84 | Bucket Group-Grapple; -Industrial | 1 |
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
156-0886 Bucket Gp-Grapple
| 15***86 | Bucket Group-Grapple; -Industrial | 1 |
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
156-0885 Bucket Gp-Grapple
| 15***85 | Bucket Group-Grapple; -Industrial | 1 |
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
286-9244 Bucket Gp-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 28***29 | Tine Group | 1 |
286-9278 Bucket Gp-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 28***43 | Fork As | 2 |
217-6228 Bucket Gp-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 21***27 | Bucket As-Grapple | 1 |
279-5359 Bucket Gp-Grapple -Industrial
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
164-7412 Bucket Gp-Light Material
| 13***86 | Edge Group-Cutting | 1 |
| 16***12 | Bucket Group-Light Material | 1 |
| 16***14 | Bucket As-Light Material | 1 |
220-4990 Bucket Gp-Light Material
| 19***24 | Edge Group-Cutting | 1 |
| 22***90 | Bucket Group-Light Material | 1 |
| 22***91 | Bucket As-Light Material | 1 |
164-7413 Bucket Gp-Light Material
| 13***87 | Edge Group-Cutting | 1 |
| 16***13 | Bucket Group-Light Material | 1 |
| 16***15 | Bucket As-Light Material | 1 |
199-8319 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 15***12 | Pin | 2 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
154-5009 Bucket Gp-Multipurpose
| 15***09 | Bucket Group-Multipurpose | 1 |
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
154-5007 Bucket Gp-Multipurpose
| 14***05 | Bearing-Sleeve | 4 |
| 14***36 | Edge | 1 |
| 15***07 | Bucket Group-Multipurpose | 1 |
279-5389 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 15***53 | Clam As-Multipurpose Bucket | 1 |
| 27***88 | Blade Group-Multipurpose Bucket | 1 |
154-5005 Bucket Gp-Multipurpose
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***05 | Bucket Group-Multipurpose | 1 |
| 15***12 | Pin | 2 |
325-7037 Bucket Gp-Multipurpose
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***12 | Pin | 2 |
| 32***37 | Bucket Group-Multipurpose | 1 |
279-5397 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 27***96 | Blade Group-Multipurpose Bucket | 1 |
279-5383 Bucket Gp-Multipurpose
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 15***12 | Pin | 2 |
| 27***83 | Bucket Group-Multipurpose | 1 |
325-7047 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 15***53 | Clam As-Multipurpose Bucket | 1 |
| 32***47 | Bucket Group-Multipurpose | 1 |
325-7057 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
| 32***57 | Bucket Group-Multipurpose | 1 |
325-7077 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 29***48 | Clam As-Multipurpose Bucket | 1 |
279-5404 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 19***08 | Clam As-Multipurpose Bucket | 1 |
| 27***04 | Bucket Group-Multipurpose | 1 |
325-7067 Bucket Gp-Multipurpose
| 15***12 | Pin | 2 |
| 19***08 | Clam As-Multipurpose Bucket | 1 |
| 32***67 | Bucket Group-Multipurpose | 1 |
285-6096 Bucket Gp-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***96 | Bucket Group-Utility | 1 |
285-6099 Bucket Gp-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***98 | Bucket As-Utility, Fuel Injection Pump; - Assembly | 1 |
165-8777 Bucket Gp-Utility
| 11***83 | Boss; (M10x1.5-Thd) | 4 |
| 13***85 | Edge Group-Cutting | 1 |
| 13***95 | Edge-Cutting | 1 |
165-8836 Bucket Gp-Utility
| 11***83 | Boss; (M10x1.5-Thd) | 1 |
| 13***84 | Edge Group-Cutting | 1 |
| 13***94 | Edge-Cutting | 1 |
165-8778 Bucket Gp-Utility
| 13***86 | Edge Group-Cutting | 1 |
| 16***47 | Bucket As-Utility | 1 |
| 16***78 | Bucket Group-Utility | 1 |
285-6102 Bucket Gp-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 28***02 | Bucket Group-Utility | 1 |
293-9429 Carriage & Fork Ar
| 19***45 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
| 29***29 | Carriage & Fork Ar | 1 |
293-9427 Carriage & Fork Ar
| 19***43 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
| 29***27 | Carriage & Fork Ar | 1 |
243-0000 Carriage & Fork Ar
| 14***11 | Carriage As-Fork | 1 |
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
242-9998 Carriage & Fork Ar
| 14***11 | Carriage As-Fork | 1 |
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
242-9999 Carriage & Fork Ar
| 14***11 | Carriage As-Fork | 1 |
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
293-9428 Carriage & Fork Ar
| 19***42 | Fork Group-Pallet | 2 |
| 26***81 | Carriage Group-Fork | 1 |
| 29***28 | Carriage & Fork Ar | 1 |
261-6681 Carriage Gp-Fork
| 15***35 | Plate-Instruction; (Load Capacity) | 1 |
| 16***89 | Tack-Fastener | 4 |
| 25***95 | Step As | 1 |
199-8308 Clam As-Multipurpose Bucket
| 14***05 | Bearing-Sleeve | 4 |
| 15***38 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 16***30 | Plate-Identification; (Cat) | 2 |
154-5053 Clam As-Multipurpose Bucket
| 14***05 | Bearing-Sleeve | 4 |
| 14***36 | Edge | 1 |
| 15***53 | Clam As-Multipurpose Bucket | 1 |
293-0148 Clam As-Multipurpose Bucket
| 14***05 | Bearing-Sleeve | 4 |
| 16***30 | Plate-Identification; (Cat) | 2 |
| 22***32 | Edge | 1 |
154-5070 Clam As-Multipurpose Bucket
| 14***05 | Bearing-Sleeve | 4 |
| 14***37 | Edge | 1 |
| 15***70 | Clam As-Multipurpose Bucket | 1 |
149-4232 Clam As-Multipurpose Bucket
| 14***05 | Bearing-Sleeve | 4 |
| 14***32 | Clam As-Multipurpose Bucket | 1 |
| 14***35 | Edge | 1 |
241-8672 Conversion Gp-Work Tool -Kit, High Flow
| 11***62 | Tube-Heat Shrink; (10.85-mm Dia)(299-cm) | 0 |
| 12***74 | Tube-Heat Shrink; (5.72-mm Dia)(950-cm) | 0 |
| 12***75 | Tube-Heat Shrink; (7.44-mm Dia)(560-cm) | 0 |
296-0582 Conversion Gp-Work Tool -Kit, High Flow
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
218-6521 Coupler Ar-Quick -Manual
| 19***70 | Coupler Group-Quick | 1 |
| 21***34 | Lines Group-Lowering Control; -Manual | 1 |
| 21***21 | Coupler Ar-Quick; -Manual | 1 |
218-6510 Coupler Ar-Quick
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 19***55 | Coupler Group-Quick; -Hydraulic | 1 |
| 21***21 | Switch As-Rocker; (Quick Coupler)(12-Volt) | 1 |
218-6509 Coupler Ar-Quick
| 19***70 | Coupler Group-Quick | 1 |
| 21***17 | Lines Group-Lowering Control; -Manual | 1 |
| 21***09 | Housing, Coupler Ar-Quick | 1 |
218-6522 Coupler Ar-Quick -Hydraulic
| 11***99 | Gasket; (Air Conditioner Control) | 1 |
| 19***55 | Coupler Group-Quick; -Hydraulic | 1 |
| 21***21 | Switch As-Rocker; (Quick Coupler)(12-Volt) | 1 |
196-8870 Coupler Gp-Quick
| 11***83 | Boss; (M10x1.5-Thd) | 6 |
| 12***01 | Plate-Retainer | 2 |
| 13***79 | Washer; (11x32x3-mm Thk) | 2 |
192-2655 Coupler Gp-Quick -Hydraulic
| 12***01 | Plate-Retainer | 2 |
| 19***55 | Coupler Group-Quick; -Hydraulic | 1 |
| 20***85 | Pin | 2 |
162-5236 Cover Gp-Lines
| 16***28 | Plate | 1 |
| 16***36 | Cover Group-Lines | 1 |
| 5C***53 | Bolt (M6x1.00x16mm); (M6x1x16mm Thk) | 5 |
215-3962 Cylinder & Link Gp-Coupler -Lh
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
| 19***42 | Pin | 1 |
| 21***57 | Link Group-Coupler | 1 |
215-3963 Cylinder & Link Gp-Coupler -Rh
| 19***40 | Cylinder Group-Hydraulic; -Coupler | 1 |
| 19***42 | Pin | 1 |
| 21***57 | Link Group-Coupler | 1 |
135-9386 Edge Gp-Cutting
| 13***86 | Edge Group-Cutting | 1 |
| 13***96 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
135-9384 Edge Gp-Cutting
| 13***84 | Edge Group-Cutting | 1 |
| 13***94 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
135-9383 Edge Gp-Cutting
| 13***83 | Edge Group-Cutting | 1 |
| 13***93 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 6 |
149-5741 Edge Gp-Cutting
| 14***41 | Edge Group-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 7 |
| 19***24 | Edge-Cutting | 1 |
195-7124 Edge Gp-Cutting
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
| 19***24 | Edge-Cutting | 1 |
| 19***24 | Edge Group-Cutting | 1 |
135-9385 Edge Gp-Cutting
| 13***85 | Edge Group-Cutting | 1 |
| 13***95 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 8 |
135-9387 Edge Gp-Cutting
| 13***87 | Edge Group-Cutting | 1 |
| 13***97 | Edge-Cutting | 1 |
| 15***53 | Screw-Flat Head; (M16x2.00 Thd) | 11 |
162-8139 Fork Ar-Grapple
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***12 | Cylinder Group-Grapple | 2 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
285-6115 Fork Ar-Grapple -Utility
| 28***10 | Fork Group-Grapple | 1 |
| 28***15 | Fork Ar-Grapple; -Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
165-8727 Fork Ar-Grapple
| 16***27 | Fork Ar-Grapple; -Utility | 1 |
| 16***34 | Grapple & Cylinder Group-Utility | 1 |
| 25***25 | Fork Group-Utility | 1 |
285-6114 Fork Ar-Grapple -Utility
| 28***05 | Fork Group-Utility | 1 |
| 28***14 | Fork Ar-Grapple; -Utility | 1 |
| 28***16 | Grapple & Cylinder Group-Utility | 1 |
163-4812 Fork Ar-Grapple
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 15***12 | Cylinder Group-Grapple | 2 |
| 16***87 | Lines Group-Grapple; -Industrial | 1 |
165-8728 Fork Ar-Grapple
| 16***28 | Fork Ar-Grapple; -Utility | 1 |
| 16***34 | Grapple & Cylinder Group-Utility | 1 |
| 25***26 | Fork Group-Utility | 1 |
279-5360 Fork Ar-Grapple -Industrial
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***14 | Fork Group-Grapple; -Industrial | 2 |
| 27***75 | Cylinder Group-Grapple; -Industrial | 2 |
279-5350 Fork Ar-Grapple -Industrial
| 15***91 | Mounting Group-Cylinder; -Industrial | 1 |
| 16***14 | Fork Group-Grapple; -Industrial | 9 |
| 27***75 | Cylinder Group-Grapple; -Industrial | 2 |
164-9614 Fork Gp-Grapple
| 16***54 | Tine | 1 |
| 16***14 | Fork Group-Grapple; -Industrial | 1 |
| 3E***70 | Pin; (Spring) | 1 |
163-4811 Fork Gp-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***11 | Fork Group-Grapple | 1 |
285-6110 Fork Gp-Grapple
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 9 |
| 28***10 | Fork Group-Grapple | 1 |
279-5351 Fork Gp-Grapple -Industrial
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
162-8140 Fork Gp-Grapple
| 15***40 | Pin | 4 |
| 15***48 | Bearing-Sleeve | 2 |
| 16***40 | Fork Group-Grapple | 1 |
195-8545 Fork Gp-Pallet
| 19***45 | Fork Group-Pallet | 1 |
| 22***29 | Positioner Group-Fork | 1 |
195-6942 Fork Gp-Pallet
| 19***42 | Fork Group-Pallet | 1 |
| 22***29 | Positioner Group-Fork | 1 |
195-6943 Fork Gp-Pallet
| 19***43 | Fork Group-Pallet | 1 |
| 22***29 | Positioner Group-Fork | 1 |
243-0002 Fork Gp-Pallet -Kit
| 19***42 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
| 24***02 | Fork Group-Pallet; -Kit | 1 |
243-0001 Fork Gp-Pallet -Kit
| 19***43 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
| 24***01 | Fork Group-Pallet; -Kit | 1 |
243-0003 Fork Gp-Pallet -Kit
| 19***45 | Fork Group-Pallet | 12 |
| 22***29 | Positioner Group-Fork | 1 |
| 24***03 | Fork Group-Pallet; -Kit | 1 |
285-6105 Fork Gp-Utility
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 7 |
| 28***05 | Fork Group-Utility | 1 |
252-8025 Fork Gp-Utility
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 7 |
| 25***25 | Fork Group-Utility | 1 |
165-8737 Fork Gp-Utility
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 9 |
| 16***37 | Fork Group-Utility | 1 |
165-8739 Fork Gp-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***39 | Fork Group-Utility | 1 |
165-8738 Fork Gp-Utility
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***38 | Fork Group-Utility | 1 |
165-8736 Fork Gp-Utility
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 7 |
| 16***36 | Fork Group-Utility | 1 |
252-8026 Fork Gp-Utility
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***32 | Fork Group-Utility | 9 |
| 25***26 | Fork Group-Utility | 1 |
165-8732 Fork Gp-Utility
| 16***32 | Fork Group-Utility | 1 |
| 16***41 | Tine | 1 |
| 9R***59 | Clip | 1 |
230-5670 Frame Gp-Blade
| 17***14 | Pin As | 1 |
| 17***55 | Shim; (1-mm Thk) | 1 |
| 17***56 | Shim; (2-mm Thk) | 1 |
279-5352 Frame Gp-Fork -Industrial
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***89 | Tack-Fastener | 4 |
279-5358 Frame Gp-Fork -Industrial
| 15***04 | Plate-Instruction; (Bucket Specifications) | 1 |
| 16***89 | Film-Warning; (Impaled Point) | 2 |
| 16***89 | Tack-Fastener | 4 |
285-6116 Grapple & Cylinder Gp-Utility
| 16***95 | Cylinder Group-Grapple | 1 |
| 16***31 | Mounting Group-Cylinder; -Utility | 1 |
| 16***40 | Grapple Group-Utility | 1 |
165-8734 Grapple & Cylinder Gp-Utility
| 16***95 | Cylinder Group-Grapple | 1 |
| 16***31 | Mounting Group-Cylinder; -Utility | 1 |
| 16***33 | Lines Group-Grapple | 1 |
165-8740 Grapple Gp-Utility
| 15***11 | Pin | 4 |
| 15***35 | Film-Warning; (Crush Hazard, Stay Back) | 2 |
| 16***40 | Grapple Group-Utility | 1 |
215-3961 Handle & Pin Gp-Coupler -Rh
| 16***60 | Pin-Spring | 1 |
| 19***42 | Pin | 1 |
| 21***59 | Handle Group-Coupler; -Rh | 1 |
215-3960 Handle & Pin Gp-Coupler -Lh
| 16***60 | Pin-Spring | 1 |
| 19***42 | Pin | 1 |
| 21***58 | Handle Group-Coupler; -Lh | 1 |
215-3958 Handle Gp-Coupler -Lh
| 19***37 | Plate | 1 |
| 19***54 | Pin-Spring | 2 |
| 21***58 | Handle Group-Coupler; -Lh | 1 |
215-3959 Handle Gp-Coupler -Rh
| 19***37 | Plate | 1 |
| 19***54 | Pin-Spring | 2 |
| 21***59 | Handle Group-Coupler; -Rh | 1 |
177-9152 Kit-Roading Plate & Mounting -Bucket
| 03***57 | Washer; (13x26x6-mm Thk) | 2 |
| 17***52 | Kit-Roading Plate & Mounting; -Bucket | 1 |
| 17***53 | Plate | 2 |
215-3957 Link Gp-Coupler
| 19***45 | Spring | 1 |
| 21***57 | Link Group-Coupler | 1 |
| 30***68 | Pin-Spring | 1 |
175-4238 Lock Gp-Quick Coupler -Mechanical
| 17***38 | Lock Group-Quick Coupler; -Mechanical | 1 |
| 17***47 | Pin | 1 |
| 9R***01 | Pin-Cotter | 1 |
184-6098 Plate Gp-Roading -Rh
| 17***14 | Film-Stripe; (Reflective, Red, White) | 1 |
| 17***15 | Film; (Reflective)(Warning) | 1 |
| 17***51 | Plate As; (Rh) | 1 |
184-6097 Plate Gp-Roading -Lh
| 17***14 | Film-Stripe; (Reflective, Red, White) | 1 |
| 17***15 | Film; (Reflective)(Warning) | 1 |
| 17***50 | Plate As; (Lh) | 1 |
247-6742 Pump Gp-Diaphragm
| 16***63 | Motor-Electric; (12-Volt) | 1 |
| 24***42 | Pump Group-Diaphragm; -Water Spray | 1 |
| 24***23 | Head-Pump | 1 |
161-7290 Pump Gp-Diaphragm
| 16***63 | Motor-Electric; (12-Volt) | 1 |
| 16***90 | Pump Group-Diaphragm; -Water Spray-Water | 1 |
| 17***33 | Head-Pump | 1 |
177-1983 Spring Gp-Blade
| 17***41 | Spring | 4 |
| 17***73 | Plate As | 1 |
| 17***83 | Spring Group-Blade | 1 |
188-7733 Step Gp-Material Handling Arm
| 18***86 | Step As | 1 |
| 18***33 | Step Group-Material Handling Arm | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 2 |
173-7407 Stop Gp-Bucket -Utility
| 17***07 | Stop Group-Bucket; -Utility | 1 |
| 2S***08 | Washer-Retaining; (0.531x3.25x0.438-In Thk) | 2 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 1 |
116-2001 Strainer Gp-Water
| 11***01 | Strainer Group-Water | 1 |
| 11***14 | Screen; (Water Tank) | 1 |
| 11***15 | Gasket | 1 |
233-5993 Tank & Mtg Gp-Water
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 09***12 | Clip | 2 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
252-0386 Tank & Mtg Gp-Water -Kit
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 06***51 | Clamp | 2 |
| 09***12 | Clip | 2 |
233-5992 Tank & Mtg Gp-Water
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 06***51 | Clamp | 2 |
| 09***12 | Clip | 2 |
346-1834 Tank & Mtg Gp-Water -Kit
| 00***43 | Elbow 5wd342 - Up Including 5wd329 - 335, 5wd337 - 340 | 1 |
| 06***51 | Clamp | 2 |
| 09***12 | Clip | 2 |
166-2551 Tank Gp-Water
| 16***51 | Tank Group-Water | 1 |
| 19***06 | Cap As; (Water Tank) | 1 |
| 19***07 | Fitting-Drain | 1 |
141-4999 Tooth Gp-Uni
| 13***20 | Tooth-Uni-Single Strap | 1 |
| 14***99 | Tooth Group-Uni | 1 |
| 24***49 | Screw-Flat Head; (M16x2-Thd) | 2 |
268B serial number reference
On the 268B the PIN plate sits at the rear of the loader frame (this generation predates Cat's later practice of duplicating the plate on the right-side curb rail). Full-length machine PINs read as a manufacturer block plus model code plus a check letter, with the 3-character family prefix embedded partway through, e.g. LBA in CAT0268BPLBA00447, followed by the unit sequence number. On the physical tag itself the prefix and sequence usually show together as LBA00001-and-up.
| Prefix | Identifies | Notes |
|---|---|---|
| LBA | 268B Skid Steer Loader, standard-flow and High-Flow XPS hydraulic configurations | Only PIN prefix documented for the 268B. Range starts at LBA1 and runs continuously through the model's production life; covers both hydraulic flow configurations, no separate prefix split by configuration found. Fitted with the Cat 3044C DIT turbocharged diesel engine across the run. Rough production span 2004-2009, based on spec references and dated field listings. |
Frequently asked questions
What engine does the Caterpillar 268B skid steer loader use?
The 268B runs a Cat 3044C DIT, a mechanically injected, turbocharged four-cylinder diesel of about 3.3 L (201 cu in). Net flywheel power is rated near 57 kW (76-77 hp), with gross power around 61 kW (82 hp); the exact figure depends on the rating standard a given source cites, so confirm against the engine plate before ordering parts.
What is the operating weight of the Caterpillar 268B?
Operating weight is about 3,626 kg (7,995 lb), with a rated operating capacity near 1,225 kg (2,700 lb) at 50% of tipping load. Figures shift slightly with cab-versus-canopy, tire, and counterweight-kit configuration, so treat this as a typical figure rather than an exact match for every unit.
What replaced the Caterpillar 268B?
There's no confirmed single 268C successor model. Around 2009 Caterpillar moved its wheeled skid steer line to the C-series, including models like the 262C and 272C with updated engines and emissions compliance. Treat this as a lineup-wide generational shift rather than a one-to-one model swap, and verify PIN and parts fitment before assuming interchange.
What 268B owners discuss
Why does a 268B sometimes only rev up while the boom or bucket is actively being moved, dropping straight back to idle the moment the joystick returns to neutral?
The 268B carries both a hand throttle, for holding one steady RPM through a job like snow blowing or trenching, and a foot throttle pedal, for varying RPM by foot pressure on load-and-carry or grading work. Owners who see engine speed chase the joystick instead of holding a set RPM are usually operating off the pedal with the hand throttle left at low idle, or have a foot-pedal linkage or position sensor that isn't holding a steady signal, so movement at the joystick is what happens to jar it into contact. The usual first checks are the hand throttle cable/detent and the pedal's linkage and sensor connection before anyone starts chasing the hydraulic pump or relief valve.
A 268B pulls hard to one side or rolls as soon as the park brake releases, before the operator gives any joystick input. What's going on?
This pattern turns up as a drive-circuit complaint on the closed-loop hydrostatic system: uneven charge pressure or a weak drive pump or motor on one side, or a park-brake release solenoid that isn't releasing in step with the interlock logic. Because the loader is moving before the operator has actually commanded it to, treat this as a stop-work fault rather than something to work around. Have your dealer verify charge pressure, the brake release circuit, and drive pump balance side to side before the machine goes back into service.
Owners report weak lift and tilt, or a bucket that slowly tips down on its own with no puddle underneath. What's the community diagnosis?
Two separate patterns get reported under this heading. Lift and tilt going noticeably weak right after a wash points to moisture getting into the pilot solenoid valves and causing them to stick, which mimics a failing pump; a pressure check at the pump against the load-sensing relief setting is used to clear the pump before solenoids get chased. A bucket that drifts down on its own with no external leak is usually internal bypass in the tilt cylinder seals, or leakage through the mechanically piloted implement control valve rather than a hose or fitting. The field test is capping the rod-end lines at the tilt cylinder and watching whether it still drifts with the lines blocked. Because a drifting cylinder under a raised or loaded attachment is a crush hazard, have your dealer verify cylinder and pilot-valve condition before anyone works underneath a raised lift arm or attachment.
What engine quirks come up specifically for the 268B, and are they shared with other Cat loaders?
The 268B runs Caterpillar's 3044C DIT, a turbocharged direct-injection diesel of roughly 3.3 L displacement rated near 57 kW net (figures cited range 76 to 77 hp depending on the spec sheet). It uses a mechanical injection pump rather than an electronic one, and its complaint list tracks that: hard or no-start reports trace back to trapped air in the fuel system, a clogging fuel filter element, worn or dirty injector nozzles, or pump timing drifting out of adjustment, rarely the injection pump itself failing outright. Power loss under load gets pinned on the same short list plus a dirty air filter and valve clearance out of spec. Turbo oil weeping past the seals is usually tied to a blocked oil feed or drain line, excess crankcase pressure from a plugged breather, or ordinary seal age rather than turbo failure. This engine and its symptom list are specific to the 3044C DIT fitted to this series; don't carry over injector or turbo experience from unrelated Cat loader engines onto a 268B.
What wears out on a 268B's drivetrain, given it rides on wheels rather than tracks?
The undercarriage-equivalent wear item here is the chain drive: each side runs drive chains in an oil-bathed case rather than a final-drive gearbox, so stretch in the chains and the condition of the chain case oil matter more than anything resembling track pads or rollers. Community and factory-interval practice is checking and re-tensioning the chains, adjustable through slots in the axle housings, around every 250 hours, with chain case oil service cited anywhere from 500 to 1,000 hours depending on the source, so treat 500 hours as the conservative check point and confirm against your machine's own maintenance sheet. Skipping that upkeep is the most common root cause behind reduced drive power or a no-drive complaint once hydraulic causes are ruled out. On tires, buyers split between air-filled for a better ride, and foam-filled or solid rubber for debris-heavy or demo sites where puncture downtime is the bigger cost.
The engine cranks and runs fine, but nothing else on the machine responds, no drive and no implements. What's the usual electrical culprit?
This is one of the most repeated complaints on the model B skid steer platform, and it is almost always the safety interlock circuit rather than the ECM. These machines run an interlock control module that reads the seat or armrest presence switch, park brake, hydraulic lockout, and door switches before it will enable drive or implement function at all, so a loose or unplugged seat-switch connector, a chafed harness wire, or a failed switch drops the whole machine into lockout exactly as designed. Techs check that circuit and its connectors before anything else; an actual ECM failure is described as uncommon. Because that circuit exists specifically to stop the machine from moving with nobody safely seated, never wire around or permanently bypass it just to get back to work. Have your dealer diagnose and repair the actual switch or harness fault instead.
What should a buyer check before purchasing a used Cat 268B?
Confirm the PIN carries the LBA prefix and that the engine actually on the machine is the 3044C DIT; paperwork mismatches show up on units that have had engine work done. Cycle the boom and bucket repeatedly, hold the bucket raised for a minute with no input, and watch for tilt drift with no puddle underneath, which is the cylinder-seal or pilot-valve issue owners commonly report and is cheap to check but expensive to ignore. Look at drive chain tension and chain case oil condition and color where an inspection point allows it; metal-flecked oil or heavily stretched chains mean drivetrain money coming. Start it cold and warm and confirm engine speed actually responds correctly to both the hand and foot throttle rather than chasing the joystick or sitting pinned at idle. Look for any aftermarket wiring spliced into the seat switch or interlock harness, a sign a previous owner bypassed the safety circuit instead of fixing it. If the machine is high-flow equipped, plug in an actual high-flow attachment and confirm the flow selector and solenoid actually switch it on rather than trusting the dash light alone. Ask for service records showing filter and injector work at or beyond the 500-hour marks. Have your dealer verify the PIN-to-engine match and interlock circuit integrity before you close the deal.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 268B part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.