Caterpillarforest productstrack feller buncher
Caterpillar 2290
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 2290 is a tracked feller buncher from the Prentice/Blount International forestry equipment lineage, one entry in a numbered carrier family that runs roughly from the 1090 up through the 2590. It was built and sold under Blount International before Caterpillar acquired Blount's forestry division in 2007, after which Cat carried the model forward as a legacy, non-current listing supported through its parts network. The configuration was a track-mounted carrier fitted with a felling head (disc saw or shear), riding a hydrostatic-drive undercarriage built for logging on steep or soft ground; the same family underpinned harvester-head configurations as well. Public documentation does not confirm the exact factory engine, rated horsepower, operating weight, or production date range for the 2290 specifically. Treat those figures as unconfirmed and pull them from the machine's serial or data plate, or verify with a Cat dealer parts lookup, rather than assuming them from sister models in the same numeric family.
Across the 1090-2590 family, Caterpillar and its Blount/Prentice predecessors kept a broadly common undercarriage, swing bearing, and hydrostatic pump architecture, which is why parts catalogs still group the 2290 alongside siblings like the 1090, 1290, 1390, 2390, and 2590, and even alongside the later Cat-branded 511, 521/522, 532, 541, and 551/552 carriers. Around 2011, Caterpillar's dedicated 500-series Zero Tail Swing track feller bunchers superseded the old numeric Blount-era line, bringing updated ACERT engines and emissions compliance the 2290 generation never had. In today's used and parts market, the 2290 survives mainly as a low-cost entry point into tracked forestry harvesting and as a donor machine for components that cross-reference into the broader family tree, rather than as a model with active factory literature or a dedicated spec sheet.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 2290 specifications
Engine
| Engine model | Not published in any available factory spec sheet. Aftermarket turbocharger and undercarriage-bushing cross-reference listings group the 2290 with the C9-powered 2390, 2391, 2491 and 2590 track feller bunchers, which points to a Cat C9 diesel, but no OEM document ties a specific engine model directly to the 2290. Verify by engine serial number plate. |
| Gross/net power | Not documented in any source found for this exact model. Not stated — verify with a dealer using the machine serial number. |
| Displacement | Not documented for the 2290 specifically. |
| Cylinders | Not documented for the 2290 specifically. |
| Emissions tier | Not documented for the 2290 specifically. The 2290 is a legacy purpose-built track feller buncher predating Cat's current C-series forestry line, so an earlier (pre-Tier or Tier 1/2) emissions rating is plausible but unconfirmed. |
Weights
| Operating weight | Not published in any available source. |
| Shipping weight | Not published in any available source. |
| Ground pressure | Not published in any available source. |
Dimensions
| Transport length | Not published in any available source. |
| Transport width | Not published in any available source. |
| Transport height | Not published in any available source. |
| Track gauge | Not published in any available source. |
| Ground clearance | Not published in any available source. |
Performance
| Travel speed | Not published in any available source. |
| Felling/dump performance | Not published in any available source. |
| Gradeability | Not published in any available source. |
Service capacities (summary)
| Fuel tank | Not published in any available source. |
| Hydraulic system | Not published in any available source. |
| Engine oil | Not published in any available source. |
| Cooling system | Not published in any available source. |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
2290 fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Cooling system | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Fuel tank | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Hydraulic system (total, includes tank) | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Hydraulic tank | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Final drives (each) | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Swing drive | Not documented in public sources | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
| Grease (spec only) | Not applicable — grease points, no fill volume | Not confirmed for this unit. Verify against the OMM for this serial range with a Cat dealer. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 2290 maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 10 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 6,000 h |
|
Servicing the 2290 beyond the schedule
Predictive Maintenance & Fluid Analysis
On the 2290's hydrostatic drive and felling head, oil analysis catches problems long before failure shows up in the field. Sample hydraulic, hydrostatic drive, engine, and final-drive oil at each scheduled interval and watch for rising metal counts that flag travel motor or pump wear. Track coolant condition and swing bearing grease consistency too. Since this carrier predates factory telematics, keep manual logs of engine hours, shear or saw cycles, and hydraulic temperature trends to predict pump, motor, and felling-head seal wear before it strands the machine in the timber.
Corrective & Common Repairs
Expect recurring wear at the felling head disc saw or shear blade, the accumulator arm cylinders, and the swing bearing on a 2290 running full shifts in timber. Hydraulic hose chafing near the boom and felling head pivots is common given the reach and vibration of shearing cycles. Track pad and roller wear accelerates on rocky or steep ground. Because this is a legacy Blount/Cat-era carrier, sourcing felling head and hydrostatic drive components often means cross-referencing parts shared across the 1090-2590 family rather than pulling from a dedicated 2290 catalog.
Overhaul & Rebuild Points
Major rebuild targets on the 2290 center on the hydrostatic travel system, the swing/slew bearing, and the undercarriage. Once oil analysis or a drop in travel performance points to pump or motor wear, plan a hydrostatic drive rebuild rather than running it to failure. Check swing bearing bolts, gear backlash, and grease seals before repeated shear-and-swing cycles loosen the felling head mount. Measure undercarriage components (chain, rollers, idlers, sprockets) against service limits rather than relying on visual inspection before committing to a full rebuild.
Seasonal & Environment Servicing
Cold starts stress the 2290's diesel and hydrostatic charge pump; run season-appropriate engine oil and hydraulic fluid viscosity and warm the hydraulic system before loading into full felling cycles. In wet or muddy ground, clear packed debris from the undercarriage and swing bearing seals daily to slow premature wear. In hot weather, watch hydraulic and hydrostatic oil temperature closely, since sustained shear-and-swing duty cycles load the cooling system hard on this tracked forestry carrier.
2290 common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 179-9348 | Valve-Drain | Fuel system service | Check fitment → |
| 1R-0762 | Filter As-Fuel | Fuel system service | Check fitment → |
| 1R-0770 | Filter As-Water Sep & Fuel | Fuel system service | Check fitment → |
| 220-8678 | Seal-Ring | Fuel system service | Check fitment → |
| 142-1339 | Filter Element As-Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
2290 fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| CID 0100 FMI 01 | Engine Oil Pressure - data valid but below normal operating range (most severe level) | Low oil level, worn oil pump, plugged oil filter, or a failed oil pressure sensor/circuit | Shut the engine down immediately, check oil level and filter condition, verify pressure with a mechanical gauge before restarting |
| CID 0100 FMI 03 | Engine Oil Pressure Sensor - voltage above normal (open circuit or short to supply) | Damaged sensor, corroded connector, or chafed harness at the sensor circuit | Inspect sensor wiring and connector, test sensor output, replace if out of range |
| CID 0110 FMI 00 | Engine Coolant Temperature - data valid but above normal range (overheat, most severe level) | Low coolant, blocked radiator core, fan drive or fan clutch failure, or a stuck thermostat | Shut down, let engine cool, check coolant level and cooling system for blockage or fan fault before restart |
| CID 0110 FMI 03 | Engine Coolant Temperature Sensor - voltage above normal (open circuit or short to supply) | Failed sensor or damaged connector/harness on the coolant temp circuit | Inspect sensor connector and wiring for corrosion or breaks, test and replace sensor if faulty |
| CID 0111 FMI 01 | Engine Coolant Level - data valid but below normal range | Low coolant in the system, air trapped in the cooling circuit, or a faulty level sensor/float | Check coolant level and top off, inspect for external leaks, verify sensor operation |
| CID 0102 FMI 10 | Boost Pressure Sensor - abnormal rate of change | Intermittent sensor signal, loose connector, or an air intake/turbo boost leak | Inspect sensor connector and intake piping, check for leaks, retest after reseating connections |
| CID 0168 FMI 02 | System (battery) voltage - data erratic, intermittent, or incorrect | Loose or corroded battery terminals, weak charging output, or a chafed main harness ground | Check battery connections and state of charge, test alternator output, inspect main harness grounds |
| CID 0247 FMI 09 | Data Link - abnormal update rate between the engine ECM and other machine control modules | Communication fault on the CAT Data Link/J1939 backbone - loose connector, damaged harness, or a module not powering up | Inspect data link wiring and connectors, check for other active codes on the machine (chassis) ECM, verify all modules are powered |
| CID 0001 FMI 05 | No. 1 Cylinder Injector Solenoid - current below normal or open circuit | Failed injector solenoid or damaged wiring/connector at the valve cover harness | Check injector wiring harness and connector, test injector solenoid resistance, replace injector if open |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
2290 attachments & work tools
Machine type and lineage
The 2290 (also listed as 2290T) is a purpose-built track feller buncher, not an excavator-based conversion. It comes from the Blount International forestry line (Prentice/CTR/Fabtek heritage) that Caterpillar absorbed into Caterpillar Forest Products and rebadged under Cat model numbers, sitting alongside other legacy-badged track bunchers such as the 1090, 1190, 1290, 1390, 2390/2391 and 2491/2590, and the Timbco-derived TK-series, ahead of Cat's later 500-series (511/521/522/532/541/551/552) that superseded this generation.
Primary work tool - felling head
The only work tool this machine class carries is a boom-tip felling head; there is no bucket/coupler ecosystem like an excavator. For this size and era of Cat/Blount track buncher, felling heads offered across the lineage were disc (circular) saw heads, bar (chainsaw) heads, and shear heads, sized to the machine's horsepower and swing-boom lift class. No felling head brand or exact model has been documented specifically for the 2290 in current dealer or parts literature - verify the head fitted to a given serial number with a dealer.
Head mounting and coupling
Felling heads on this class of machine pin directly to a boom-tip bracket and ride on an integrated hydraulic rotator (tilt/rotate unit), rather than using a pin-grab or wedge-style quick coupler common on excavator attachments. Swapping head types on these purpose-built bunchers is a dealer or shop-level job involving matching the bracket and rotator, not a field quick-change.
Hydraulic supply for the felling head
Saw or shear drive, accumulator-arm clamp function, and head rotation run off the machine's own dedicated attachment hydraulic circuit and pump, since the felling head is a factory-designed part of the machine rather than an add-on. No aftermarket auxiliary hydraulic kit is needed to run the head; any hydraulic work is normal service/repair on the existing felling-head circuit.
Cat HF-series felling heads (current lineup) - not confirmed compatible
Caterpillar's current HF-series felling heads (e.g. HF201B) are published as compatible with the newer 511/521/522/532/551 track feller bunchers. Cat's own compatibility literature does not list the 2290 among supported carriers, so these current heads should not be assumed to fit the 2290 without dealer confirmation.
Undercarriage and guarding configuration
As a dedicated forestry track carrier, the 2290 runs a forestry-duty undercarriage (wide track pads for flotation) as a built-in machine spec rather than a bolt-on option. Machines in this class and era were commonly factory- or dealer-fitted with operator protective structure (OPS/FOPS) guarding, screened cab glass, and belly/undercarriage guarding for logging debris; itemized factory option codes specific to the 2290 are not documented in available sources - confirm actual guarding fitment by serial number with a dealer.
Boom and reach configuration
Track feller bunchers in this lineage were offered with fixed or telescoping/knuckle-boom arrangements affecting maximum reach, which is the main factory configuration choice tied to felling-head placement and tree size handled. No 2290-specific boom reach or lift-capacity figures were found in available literature; treat any reach/capacity numbers for this exact model as unverified without a dealer spec sheet.
All 2290 assemblies by section
Every catalogued assembly group for the Caterpillar 2290. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
317-9524 Air Cleaner Gp
| 17***70 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 23***24 | Pump Group-Fuel Transfer | 1 |
| 31***24 | Air Cleaner Group | 1 |
210-9245 Air Cleaner Gp
| 10***07 | Seal-O-Ring; (Fuel System) | 1 |
| 14***03 | Seal-O-Ring; (Fuel System) | 2 |
| 14***40 | Ring-Backup; (37.36mm Od), Flasher Switch; Hazard, Replaces 421164a1, Flasher Switch | 1 |
216-9856 Air Cleaner Gp -With Precleaner
| 06***51 | Clamp | 2 |
| 09***86 | Clamp; (Hose) | 3 |
| 14***19 | Connector As | 1 |
173-6107 Elbow Gp-Air Inlet
| 17***07 | Elbow Group-Air Inlet | 1 |
| 23***51 | Bolt-Socket Head; (M8x1.25x65-mm) | 2 |
| 29***71 | Injector Group-Fuel | 1 |
328-9980 Lines Gp-Air
| 23***51 | Bolt-Socket Head; (M8x1.25x65-mm) | 2 |
| 32***73 | Injector Group-Fuel | 1 |
| 32***80 | Lines Group-Air | 1 |
202-0996 Manifold Gp-Exhaust
| 03***94 | Connector-Flared | 1 |
| 13***27 | Seal-O-Ring; (19.18mm Id Base Side) | 2 |
| 20***96 | Manifold Group-Exhaust | 1 |
216-9857 Muffler Gp
| 03***50 | Elbow (Check Valve Drain Tube) | 1 |
| 15***06 | Seal-O-Ring; (11.89mm Id) | 1 |
| 18***99 | Connector As | 2 |
258-8337 Turbocharger Gp
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
| 23***43 | Regulator Group-Fuel Pressure | 1 |
| 25***37 | Turbocharger Group | 1 |
250-7700 Turbocharger Gp
| 25***00 | Turbocharger Group | 1 |
| 29***20 | Regulator As; (Fuel Pressure) | 1 |
| 6V***49 | Seal-O-Ring (Id=11.89mm); (11.89-mm Id) | 1 |
Basic Engine
224-7846 Belt Tensioner Gp
| 13***19 | Seal-Integral; (Integral) | 1 |
| 22***46 | Belt Tensioner Group | 1 |
| 4W***26 | Cover | 1 |
242-0674 Camshaft Gp
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 12***57 | Washer; (10.85x19.3x1.27-mm Thk) | 2 |
| 13***22 | Stud | 2 |
202-3301 Cover Gp-Cylinder Block -Crankcase
| 20***01 | Cover Group-Cylinder Block; -Crankcase | 1 |
| 21***01 | Seal-Bulk; (23-Dm)(Valve Mechanism Cover) | 0 |
| 22***31 | Cap As-Filler; (Engine Oil) | 1 |
133-3089 Cover Gp-Flywheel Housing
| 13***89 | Cover Group-Flywheel Housing | 1 |
| 15***39 | Bearing-Main; (Standard) | 7 |
| 1B***05 | Key; (Woodruff) | 1 |
118-1727 Cover Gp-Front Housing -Accessory Drive
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 2 |
| 11***27 | Cover Group-Front Housing; -Accessory Drive | 1 |
| 17***54 | Bolt-Hex Head; (M16x160mm) | 14 |
211-3285 Cover Gp-Front Housing
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 0S***19 | Plug-Cup | 1 |
| 18***09 | Plug As; (High Temperature) | 1 |
280-8003 Cover Gp-Valve Mechanism
| 16***24 | Seal-Liner | 6 |
| 19***62 | Liner-Cylinder Block | 6 |
| 22***48 | Cylinder Block As | 1 |
164-6148 Crankshaft Gp
| 16***48 | Crankshaft Group | 1 |
| 21***17 | Insert-Valve Seat; (Exhaust)(Standard) | 12 |
| 22***00 | Sleeve-Injector | 6 |
325-3915 Cylinder Block As
| 18***15 | Gasket Assem. | 1 |
| 25***39 | Cylinder Head Group | 1 |
| 2A***46 | Plug 9.80mm(.386in.)Outside Dia. | 1 |
220-1951 Cylinder Block Gp
| 14***95 | Plug As | 2 |
| 16***78 | Seal-Valve Stem; (Exhaust) | 12 |
| 19***15 | Spring-Valve; (Inner) | 12 |
220-1952 Cylinder Block Gp
| 15***36 | Pulley-Crankshaft; (8-Groove) | 1 |
| 16***21 | Damper Assem. | 1 |
| 22***52 | Cylinder Block Group | 1 |
332-3619 Cylinder Head As
| 21***23 | Bracket As | 1 |
| 33***19 | Cylinder Head As | 1 |
| 4W***03 | Cup-Roller Bearing | 2 |
242-0672 Cylinder Head Gp
| 24***72 | Cylinder Head Group | 1 |
| 26***15 | Bolt-12 Point Head; (M16x2x180-mm) | 1 |
| 29***84 | Fastener Group-Cylinder Head | 26 |
252-8439 Cylinder Head Gp
| 22***21 | Spacer; (101.5x167x8-mm Thk) | 1 |
| 25***39 | Cylinder Head Group | 1 |
| 6V***49 | Bolt; (M10x1.5x50-mm) | 8 |
165-4557 Damper & Pulley Gp
| 16***57 | Damper & Pulley Group | 1 |
| 5P***47 | Washer (Bracket To Valve Support) | 8 |
| 9X***21 | Bolt; (Locking) (M16x2.0x45mm) | 8 |
231-6686 Drive Gp-Fan
| 09***49 | Bolt; (M8x1.25x40-mm) | 11 |
| 23***86 | Drive Group-Fan | 1 |
| 8T***24 | Washer-To Assemble Valve As And Plates | 11 |
213-4363 Fastener Gp-Cylinder Head
| 21***63 | Fastener Group-Cylinder Head | 1 |
| 24***00 | Spring | 9 |
| 8T***00 | Bolt (M8x1.25x60mm); (M8x1.25x60-mm) | 9 |
218-0859 Fastener Gp-Damper & Pulley
| 21***59 | Fastener Group-Damper & Pulley | 1 |
| 25***51 | Gear-Flywheel; (113-Teeth) | 1 |
| 25***61 | Flywheel As | 1 |
117-2794 Fastener Gp-Flywheel
| 11***69 | Plate-Thrust | 1 |
| 11***72 | Bearing | 1 |
| 11***19 | Plate-Retaining | 1 |
236-7315 Fastener Gp-Valve Cover
| 06***55 | Seal-O-Ring (Id=47.22mm) | 1 |
| 13***89 | Clip; (Ladder) | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
233-0423 Fastener Gp-Valve Cover Base
| 23***23 | Fastener Group-Valve Cover Base | 1 |
| 24***59 | Housing-Front | 1 |
| 6V***18 | Bolt (M8x1.25x50mm); (M8x1.25x50-mm) | 4 |
116-5386 Flywheel Gp
| 11***86 | Flywheel Group | 1 |
| 16***85 | Plate-Lifting; (Rear) | 1 |
| 22***66 | Plate-Lifting; (Front) | 1 |
205-1321 Gear Gp-Front
| 09***88 | Clamp; (Hose) | 1 |
| 10***37 | Washer; (24.5x135x12-mm Thk) | 2 |
| 11***30 | Support As | 2 |
187-0473 Housing Gp-Flywheel
| 14***95 | Plug As | 1 |
| 14***08 | Plug As. | 1 |
| 18***73 | Housing Group-Flywheel | 1 |
245-3260 Housing Gp-Front
| 16***94 | Bearing; (Connecting Rod) | 1 |
| 16***97 | Bolt | 2 |
| 16***99 | Rod Assem. | 1 |
191-3063 Lifting Gp-Engine
| 14***08 | Plug As. | 1 |
| 18***06 | Plug As; (High Temperature) | 2 |
| 19***63 | Lifting Group-Engine | 1 |
216-9855 Mounting Gp-Engine
| 16***47 | Rocker Arm As | 1 |
| 21***55 | Mounting Group-Engine | 1 |
| 26***24 | Screw-Valve Adjustment; (M10x1.5-Thd) | 1 |
219-9943 Pan Gp-Oil
| 21***43 | Pan Group-Oil | 1 |
| 24***28 | Rocker Arm As | 1 |
| 26***24 | Screw-Valve Adjustment; (M10x1.5-Thd) | 1 |
265-1400 Piston & Rod Gp
| 20***19 | Bolt Assem.; (M6x1) | 9 |
| 24***39 | Seal-Crankshaft; (Front)(Front) | 1 |
| 26***00 | Piston & Rod Group | 1 |
169-3105 Plug Gp-Engine
| 16***05 | Plug Group-Engine | 1 |
| 17***01 | Support-Front | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 6 |
213-9320 Rocker Arm Gp -Exhaust
| 16***45 | Shaft As-Rocker Arm | 1 |
| 16***59 | Spring | 6 |
| 16***69 | Stand; (End) | 2 |
242-0329 Rocker Arm Gp -Inlet
| 16***37 | Lifter As-Valve | 12 |
| 21***26 | Valve Mechanism Group | 1 |
| 24***29 | Rocker Arm Group; -Inlet | 1 |
178-3899 Seal Gp-Crankshaft
| 17***99 | Seal Group-Crankshaft | 1 |
| 21***10 | Gasket | 1 |
| 21***11 | Cover; (Cylinder Block) | 1 |
172-0961 Support Gp-Engine
| 03***53 | Seal-O-Ring; (08.92mm Id) | 1 |
| 03***42 | Seal-O-Ring; (11.89mm Id) | 2 |
| 17***61 | Support Group-Engine | 1 |
242-0447 Valve Mechanism Gp
| 18***16 | Tube As-Guide; (Rh) | 1 |
| 21***59 | Gauge-Oil Level (Dipstick); (Engine) | 1 |
| 24***47 | Valve Mechanism Group | 1 |
212-8926 Valve Mechanism Gp
| 21***26 | Valve Mechanism Group | 1 |
| 22***18 | Bracket | 1 |
| 22***34 | Hose-Fumes Disposal | 1 |
Cooling System
188-3826 Cooler Gp-Engine Oil
| 11***73 | Bolt-12 Point Head; (M10x1.5x35-mm) | 4 |
| 13***40 | Spider As-Fan; (8-Blade) | 1 |
| 18***26 | Cooler Group-Engine Oil | 1 |
216-9860 Cooling Ar
| 12***67 | Clip Loop | 1 |
| 18***94 | Clip | 1 |
| 1P***79 | Flange (Half) | 8 |
216-9864 Fan Ar-Reversible
| 21***64 | Fan Ar-Reversible | 1 |
| 21***52 | Pump Group-Water | 1 |
| 2M***53 | Seal--To Seal Brake Housing To Main Housing | 1 |
223-7634 Fan Gp-Reversible
| 14***88 | Seal As; (Water Pump) | 1 |
| 17***44 | Cover | 1 |
| 17***52 | Shaft As | 1 |
216-9871 Fan Gp-Suction
| 08***10 | Spacer; (16.6x32x26-mm Thk) | 4 |
| 09***35 | Spacer; (11x25x20-mm Thk) | 1 |
| 09***88 | Clamp; (Hose) | 1 |
248-8835 Housing & Regulator Gp
| 14***52 | Cap-Radiator | 1 |
| 24***35 | Housing & Regulator Group; -Temperature Regulator | 1 |
216-9863 Lines Gp-Cooling -Rad, Aftercooler, Hyd Cooler
| 14***39 | Filter Element As-Air; (Primary) | 1 |
| 14***04 | Filter Element As-Air; (Secondary) | 1 |
| 17***92 | Cover As | 1 |
244-0989 Lines Gp-Turbocharger Water
| 09***35 | Spacer; (11x25x20-mm Thk) | 3 |
| 18***03 | Hose-Elbow | 1 |
| 18***30 | Hose-Elbow | 1 |
205-4013 Plug Gp-Water Lines
| 13***53 | Stud; (M8x1.25x82.75-mm)(M8x1.25x82.75-mm) | 8 |
| 18***71 | Elbow-Air Inlet | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
202-7674 Pump Gp-Water
| 20***74 | Pump Group-Water | 1 |
219-4452 Pump Gp-Water
| 11***15 | Stud-Taperlock; (M10x85-mm Oal) | 12 |
| 16***11 | Gasket | 6 |
| 19***97 | Manifold-Exhaust | 1 |
226-3629 Radiator & Hyd Oil Cooler Gp
| 09***35 | Spacer; (11x25x20-mm Thk) | 3 |
| 13***81 | Clamp As | 1 |
| 20***80 | Muffler As | 1 |
216-9862 Radiator & Mounting Gp
| 14***75 | Valve-Drain; (Fuel) | 1 |
| 16***77 | Plug As | 2 |
| 17***48 | Valve-Drain; (Fuel Filter) | 1 |
235-1016 Radiator Gp
| 1R***70 | Filter As-Water Sep & Fuel; (Primary) | 1 |
| 22***78 | Seal-Ring; (Fuel And Water Sep Filter) | 1 |
| 23***16 | Radiator Group | 1 |
Electrical And Starting System
3e-6328 Alarm Gp -Action
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 3E***28 | Alarm Group; -Caterpillar Monitoring System-Action | 1 |
197-8820 Alternator Gp-Charging
| 09***50 | Nut-Wing | 1 |
| 19***20 | Alternator Group-Charging; -24-Volt, 95-Ampere | 1 |
| 21***85 | Lamp Group-Flood; -24-Volt-Front | 3 |
217-6635 Alternator Gp-Charging
| 09***46 | Screw-Machine; (M8x1.25x16-mm) | 4 |
| 21***35 | Alternator Group-Charging | 1 |
| 23***25 | Lamp Group-Flood; -Suspended Mount | 2 |
319-8882 Battery & Wiring Gp
| 31***82 | Battery & Wiring Group | 1 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 2 |
| 7X***08 | Washer-Hard; (10.2x16x2-mm Thk) | 2 |
321-7032 Battery & Wiring Gp -Heavy Duty
| 13***24 | Circuit Breaker As; (30-Ampere) | 1 |
| 17***06 | Circuit Breaker As; (50-Ampere) | 1 |
| 17***10 | Circuit Breaker As; (80-Ampere) | 1 |
340-9411 Battery & Wiring Gp -Heavy Duty
| 13***00 | Clip; (Tab) | 7 |
| 13***89 | Clip; (Ladder) | 1 |
| 17***00 | Suppressor-Arc | 1 |
9w-0742 Block Gp-Junction -Battery
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 24***53 | Plug As | 1 |
| 3S***93 | Strap-Cable-To Tie Harnesses Together | 1 |
246-9365 Control & Mtg Gp-Engine Elek
| 03***54 | Elbow; (90 Degree Bumped Tube) | 2 |
| 13***00 | Clip; (Tab) | 1 |
| 13***87 | Clip | 1 |
226-7473 Control Gp-Engine Electronic
| 09***86 | Seal - O-Ring (19.80 mm Id) | 1 |
| 13***73 | Hose-Fuel; (14 cm) | 0 |
| 13***08 | Clamp | 2 |
320-1521 Electrical Ar
| 19***93 | Sensor Group-Pressure; -Atmospheric | 1 |
| 19***94 | Sensor Group-Pressure; -Engine Oil | 1 |
| 21***47 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
285-5315 Guard Gp-Electronic Control
| 16***03 | Sensor Group-Pressure; (Turbocharger Inlet, Rh) | 1 |
| 28***15 | Guard Group-Electronic Control | 1 |
| 6V***49 | Seal-O-Ring (Id=11.89mm); (11.89-mm Id) | 1 |
162-7755 Lamp Gp-Dome
| 16***05 | Sensor As-Pressure; (Unfiltered Engine Oil) | 1 |
| 16***55 | Lamp Group-Dome; -Cab | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
319-7380 Lamp Gp-Flood -Hid
| 13***45 | Pad; (Connector) | 1 |
| 26***97 | Sensor Group-Temperature; (Air Inlet Manifold) | 1 |
| 31***80 | Lamp Group-Flood; -Hid | 1 |
219-6485 Lamp Gp-Flood
| 16***04 | Sensor Group-Pressure; (Turbocharger Outlet) | 1 |
| 21***85 | Lamp Group-Flood; -24-Volt-Front | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
319-7379 Lamp Gp-Flood -Hid
| 20***40 | Seal-O-Ring; (13.94mm Id) | 2 |
| 24***30 | Sensor Group-Speed; -Engine Timing | 1 |
| 31***79 | Lamp Group-Flood; -Hid | 1 |
219-6487 Lamp Gp-Flood
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***76 | Wedge-Plug Lock; (3-Pin) | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 3 |
234-4325 Lamp Gp-Flood
| 21***67 | Seal-O-Ring | 1 |
| 22***36 | Sensor Group-Pressure; -Injection Actuation | 1 |
| 23***25 | Lamp Group-Flood; -Suspended Mount | 1 |
321-0836 Lamp Gp-Flood
| 13***45 | Pad; (Connector) | 1 |
| 26***97 | Sensor Group-Temperature; (Air Inlet Manifold) | 1 |
| 32***36 | Lamp Group-Flood | 1 |
261-1091 Lighting Gp-Flood -Cab Front, Rear, Side, Engine Compartment
| 13***00 | Clip; (Tab) | 1 |
| 16***95 | Block | 2 |
| 23***45 | Nut-Sleeve; (5/16-24-Thd) | 1 |
320-7443 Lighting Gp-Flood -Cab Front, Side
| 21***70 | Preheater Group-Machine; -Hydraulic Tank, Engine | 1 |
| 31***26 | Starting Aid Group-Ether | 1 |
| 32***43 | Lighting Group-Flood; -Cab Front, Side | 1 |
332-8810 Lighting Gp-Flood -Hid
| 31***26 | Starting Aid Group-Ether | 1 |
| 32***32 | Battery & Wiring Group; -Heavy Duty | 1 |
| 33***10 | Lighting Group-Flood; -Hid | 1 |
332-8811 Lighting Gp-Flood -Hid
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 13 |
| 04***65 | Screw 19.05 mm(.750 In.) Long | 4 |
117-3915 Motor Gp-Electric -Hydraulic Tank
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 19***70 | Solenoid As-Starting Motor; (24-Volt)(Starting Motor) | 1 |
320-6147 Panel Gp-Circuit Breaker
| 10***41 | Starting Motor Group-Electric | 1 |
| 1S***51 | Terminal-Cable; (00-Ga, 1/2-In Screw) | 1 |
| 1S***52 | Terminal-Cable; (00-Ga, 3/8-In Screw) | 1 |
238-5022 Panel Gp-Relay
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 23***22 | Panel Group-Relay, O-Ring | 1 |
235-8200 Plug Gp-Connector -Engine Harness, Protective Cover
| 23***00 | Plug Group-Connector; -Engine Harness, Protective Cover | 1 |
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
224-9686 Preheater Gp-Machine -Diesel Fired
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
| 22***86 | Preheater Group-Machine; -Diesel Fired | 1 |
216-9870 Preheater Gp-Machine -Hydraulic Tank, Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 21***70 | Preheater Group-Machine; -Hydraulic Tank, Engine | 1 |
231-1978 Sensor Gp-Engine
| 08***83 | Washer; (0.8mm Thk) | 2 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 11***99 | Switch As; (Hydraulic Lockout, Neutral Start) | 1 |
330-6034 Sensor Gp-Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 33***34 | Sensor Group-Engine | 1 |
306-6875 Sensor Gp-Liquid Level
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 30***75 | Sensor Group-Liquid Level | 1 |
197-8394 Sensor Gp-Pressure
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***75 | Horn As; (24-Volt, High Tone) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
266-8650 Sensor Gp-Pressure
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***09 | Knob-Control | 1 |
210-1747 Sensor Gp-Pressure
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 21***47 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
236-6220 Sensor Gp-Pressure
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***61 | Housing | 1 |
197-8393 Sensor Gp-Pressure
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 19***93 | Sensor Group-Pressure; -Atmospheric | 1 |
303-3357 Sensor Gp-Pressure
| 17***13 | Ring-Terminal | 1 |
| 20***77 | Bolt-Flange Head; (M8x1x25-mm) | 2 |
| 20***82 | Switch Group-Magnetic; -Starting Aid Heater Relay-Air Inlet Heater Relay | 1 |
224-4536 Sensor Gp-Pressure
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 21***85 | Lamp Group-Flood; -24-Volt-Front | 2 |
267-1402 Sensor Gp-Pressure
| 21***49 | Harness Assembly; (Unit Injector) | 1 |
| 23***02 | Harness Assembly; (Electronic Control Module) | 1 |
| 26***02 | Sensor Group-Pressure; -Injection Actuation | 1 |
276-9067 Sensor Gp-Pressure
| 03***12 | Terminal-Ring; (2-Ga, 1/4-In Screw)(Circuit Breaker) | 1 |
| 12***33 | Clip | 1 |
| 13***00 | Clip; (Tab) | 2 |
236-6221 Sensor Gp-Speed -Engine Timing
| 03***07 | Terminal-Ring; (0-Ga, 3/8-In Screw) | 1 |
| 11***97 | Diode As; (Bipolar) | 1 |
| 13***43 | Boot; (Red)(Red) | 1 |
234-5013 Sensor Gp-Temperature
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 5 |
| 10***05 | Seal-O-Ring | 1 |
| 13***04 | Ring-Retaining; (89.5mm Id) | 1 |
274-7395 Sensor Gp-Temperature
| 19***68 | Final Drive Group | 1 |
| 27***95 | Sensor Group-Temperature; -Air Inlet Manifold | 1 |
| 27***72 | Motor Group-Travel | 1 |
234-5012 Sensor Gp-Temperature
| 03***48 | Clip; (11.11mm .437in Id) | 3 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
274-7396 Sensor Gp-Temperature
| 27***96 | Sensor Group-Temperature; -Engine Coolant | 1 |
| 6Y***98 | Sprocket - Track (21 Teeth) | 1 |
| 8T***30 | Capscrew; (Use 12-16) (Hex Hd) (M20x2.5x50) (Gd 10.9 Z) | 18 |
238-3215 Starting Aid Gp -Air Inlet Manifold
| 23***15 | Starting Aid Group; -Air Inlet Manifold | 1 |
| 31***10 | Box As-Battery, Exhaust Valve, Exhaust Valve; Serviced As 38***91. | 1 |
| 31***25 | Plate | 2 |
329-9549 Starting Aid Gp-Ether
| 14***06 | Plug As | 1 |
| 18***06 | Plug As; (High Temperature) | 1 |
| 21***60 | Plate As | 1 |
327-5254 Starting Ar-Cold Weather
| 11***83 | Seal (1100 cm) (Order By The Centimeter) | 0 |
| 32***54 | Starting Ar-Cold Weather | 1 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
327-5253 Starting Ar-Cold Weather -Preheater
| 08***87 | Grommet | 5 |
| 09***83 | Shim (1.0 mm Thick) | 1 |
| 09***90 | Shim (1.0 mm Thick) | 2 |
104-7041 Starting Motor Gp-Electric
| 10***41 | Starting Motor Group-Electric | 1 |
| 19***78 | Gear & Bearing Group-Swing | 1 |
| 22***88 | Gear & Bearing Group-Swing | 1 |
338-3454 Starting Motor Gp-Electric
| 20***38 | Rod As | 1 |
| 22***44 | Cover | 2 |
| 22***43 | Angle | 1 |
223-6377 Starting Motor Gp-Electric
| 22***77 | Starting Motor Group-Electric | 1 |
| 22***73 | Seal-Dust | 2 |
| 3B***89 | Fitting-Grease; (Fan And Alternator Drive) | 1 |
237-1962 Starting Motor Gp-Electric
| 1K***50 | Spring | 1 |
| 23***62 | Starting Motor Group-Electric | 1 |
| 25***84 | Plate | 1 |
6v-0590 Starting Motor Gp-Electric
| 09***95 | Plug | 1 |
| 1U***46 | Sealant (For Locations A) | 0 |
| 22***87 | Gear & Bearing Group-Swing | 1 |
7n-0718 Switch Gp-Disconnect -Battery
| 12***36 | Handle | 2 |
| 26***82 | Latch As; (Heavy-Duty) | 1 |
| 26***11 | Plate | 1 |
241-8368 Switch Gp-Magnetic -Main Relay
| 11***31 | Mount Assem. | 8 |
| 24***68 | Switch Group-Magnetic; -Main Power Relay-Main Relay | 1 |
| 24***98 | Sleeve | 8 |
179-0006 Switch Gp-Magnetic -Hyd Tank Fill Pump/Motor Relay
| 10***73 | Cover As | 1 |
| 17***06 | Switch Group-Magnetic; -Hydraulic Tank Fill Pump/Motor Relay | 1 |
| 3B***32 | Cotter; (Pin) | 1 |
209-5582 Switch Gp-Magnetic -Start Relay-Starting Aid Heater Relay
| 15***11 | Lockwasher | 3 |
| 15***59 | Eyebolt; (M8x1.25x100-mm) | 2 |
| 20***82 | Switch Group-Magnetic; -Starting Aid Heater Relay-Air Inlet Heater Relay | 1 |
234-6613 Switch Gp-Position -Hydraulic Lockout
| 11***23 | Stud-Weld; (M10x1.5x25-mm) | 2 |
| 23***13 | Switch Group-Position; -Hydraulic Lockout | 1 |
| 7T***99 | Link | 6 |
258-0883 Switch Gp-Pressure -Fuel Filter, Differential-Fuel Filter
| 17***94 | Pin As | 2 |
| 23***25 | Step As | 1 |
| 25***83 | Switch Group-Pressure; -Fuel Filter, Differential-Fuel Filter | 1 |
165-5970 Switch Gp-Toggle -Hyd Tank Fill Pump, Motor
| 16***70 | Switch Group-Toggle; -Engine Shutoff-Starting Aid-Diagnostic Mode Select | 1 |
| 8T***23 | Washer-Plated; (22x35x3.5-mm Thk) | 40 |
| 8T***41 | Bolt-Plt; (M20 X 2.5 X 70) | 40 |
158-6634 Switch Gp-Toggle
| 09***36 | Seal-Lip Type | 1 |
| 09***12 | Ring, Back-Up | 2 |
| 09***19 | Seal-O-Ring (Id=59.60mm) | 2 |
239-1134 Valve Gp-Ether Starting
| 13***48 | Plate-Step | 2 |
| 20***98 | Plate-Cover | 2 |
| 23***34 | Valve Group-Ether Starting | 1 |
217-2437 Warning Gp-Backup
| 10***85 | Seal Group-Duo-Cone | 2 |
| 11***51 | Shaft-Idler | 1 |
| 11***97 | Bearing | 2 |
253-2606 Wiring Gp-Boom -Floodlights
| 25***06 | Wiring Group-Boom; -Floodlights | 1 |
| 26***11 | Link-Track; (Rh) | 46 |
| 26***12 | Link-Track; (Lh) | 46 |
212-8018 Wiring Gp-Boom -Floodlights
| 10***09 | Track Adjuster Group | 2 |
| 11***17 | Idler Group-Front; (Front) (B) | 2 |
| 21***18 | Wiring Group-Boom; -Floodlights | 1 |
280-0558 Wiring Gp-Cab
| 20***63 | Roller Group-Track-Double Flange | 14 |
| 20***64 | Roller Group-Track-Single Flange | 4 |
| 28***58 | Wiring Group-Cab | 1 |
280-0561 Wiring Gp-Console
| 15***86 | Collar; (Track Roller) | 2 |
| 15***26 | Dowel | 2 |
| 20***62 | Roller & Bearing As | 1 |
330-6018 Wiring Gp-Electronic Control
| 20***64 | Roller Group-Track-Single Flange | 1 |
| 22***10 | Plate | 1 |
| 22***11 | Plate | 1 |
236-6226 Wiring Gp-Electronic Control -Engine
| 15***86 | Collar; (Track Roller) | 2 |
| 15***26 | Dowel | 2 |
| 20***12 | Seal Group-Duo-Cone | 2 |
320-8403 Wiring Gp-Engine
| 10***76 | Support As | 1 |
| 10***80 | Spring | 1 |
| 10***81 | Support | 1 |
269-3410 Wiring Gp-Heater -Air Inlet Manifold
| 20***64 | Roller Group-Track-Single Flange | 6 |
| 26***10 | Wiring Group-Heater; -Air Inlet Manifold | 1 |
| 29***71 | Track Group; -Rh | 1 |
255-6927 Wiring Gp-Hyd Tank Fill Pump
| 25***27 | Wiring Group-Hydraulic Tank Fill Pump | 1 |
| 26***24 | Link As-Track; -Grease Lubricated Track-Positive Pin Retention | 1 |
| 30***48 | Bolt-Track; (M20x1.5x68-mm) | 184 |
320-1523 Wiring Gp-Machine
| 15***28 | Shoe-Track | 46 |
| 26***24 | Link As-Track; -Grease Lubricated Track-Positive Pin Retention | 1 |
| 30***48 | Bolt-Track; (M20x1.5x68-mm) | 184 |
Engine Arrangement
264-0397 Engine Ar-Complete
| 18***49 | Support | 1 |
| 19***43 | Belt Tensioner | 1 |
| 26***97 | Engine Ar-Complete | 1 |
264-0401 Engine Ar-Core
| 10***94 | Plate-Thrust | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 22***47 | Gear; (100-Teeth) | 1 |
213-2400 Installation Ar-Engine
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 3 |
| 21***00 | Installation Ar-Engine | 1 |
| 4D***04 | Washer,Flat Cover Mtg,Accessory Drive | 3 |
Frame And Body
316-6440 Box Gp-Battery
| 22***04 | Roller Group-Track-Single Flange | 6 |
| 26***26 | Track Group | 2 |
| 31***40 | Box Group-Battery | 1 |
333-0597 Brace Gp
| 22***04 | Roller Group-Track-Single Flange | 6 |
| 26***21 | Track Group | 2 |
| 33***97 | Brace Group | 1 |
272-0054 Counterweight Gp
| 20***64 | Roller Group-Track-Single Flange | 6 |
| 26***25 | Track Group | 2 |
| 27***54 | Counterweight Group | 1 |
356-6534 Counterweight Gp
| 20***64 | Roller Group-Track-Single Flange | 6 |
| 26***26 | Track Group | 2 |
| 35***34 | Counterweight Group | 1 |
356-6535 Counterweight Gp
| 20***64 | Roller Group-Track-Single Flange | 6 |
| 26***21 | Track Group | 2 |
| 35***35 | Counterweight Group | 1 |
340-9880 Door As-Access
| 10***21 | Guard Group-Swivel; (Swivel) | 1 |
| 11***09 | Idler Group-Front | 1 |
| 1C***74 | Fastener Group-Carbody | 1 |
272-0052 Frame Gp-Upper
| 27***52 | Frame Group-Upper | 1 |
| 2J***64 | Plug-Drain; (Hydraulic Filter Bypass) | 1 |
| 3G***73 | Spring; (Inner) | 1 |
227-6087 Gear & Bearing Gp-Swing
| 17***22 | Elbow | 2 |
| 1P***03 | Seal - Rectangular (31.86mm Id) | 2 |
| 22***87 | Gear & Bearing Group-Swing | 1 |
225-3984 Gear & Bearing Gp-Swing
| 14***76 | Elbow As | 1 |
| 17***22 | Elbow | 2 |
| 1P***03 | Seal - Rectangular (31.86mm Id) | 2 |
199-4478 Gear & Bearing Gp-Swing
| 12***62 | Seal-O-Ring | 1 |
| 17***30 | Cover | 1 |
| 19***78 | Gear & Bearing Group-Swing | 1 |
227-6088 Gear & Bearing Gp-Swing
| 14***76 | Elbow As | 1 |
| 17***22 | Elbow | 2 |
| 1P***03 | Seal - Rectangular (31.86mm Id) | 2 |
321-8957 Guard Gp-Lighting
| 28***13 | Cylinder & Mtg Group-Stick | 1 |
| 28***52 | Cylinder & Mtg Group-Saw | 1 |
| 32***57 | Guard Group-Lighting | 1 |
247-7641 Guard Gp-Radiator
| 08***05 | Stop | 1 |
| 09***29 | Ring; (Retaining) | 2 |
| 09***31 | Seal-O-Ring; (Id=119.60mm) | 1 |
216-9865 Guard Gp-Radiator
| 10***17 | Valve Group-Counterbalance; -Hood Tilt Cylinder | 1 |
| 11***15 | Clevis | 1 |
| 21***65 | Guard Group-Radiator | 1 |
340-9907 Guard Gp-Radiator
| 09***71 | Ring; (Retaining) | 1 |
| 09***29 | Ring; (Retaining) | 2 |
| 09***31 | Seal-O-Ring; (Id=119.60mm) | 1 |
100-3721 Guard Gp-Swivel
| 09***55 | Pin | 1 |
| 10***21 | Guard Group-Swivel; (Swivel) | 1 |
| 11***29 | Bolt; (M24x3x100-mm) | 16 |
330-5882 Hood As
| 09***30 | Ring; (Retaining) | 2 |
| 09***31 | Ring - Retaining | 1 |
| 09***57 | Gauge-Oil Level (Dipstick) | 1 |
272-0053 Hood Gp
| 20***08 | Drive Group-Swing | 1 |
| 27***53 | Hood Group | 1 |
| 28***04 | Motor & Mtg Group-Swing | 1 |
331-9410 Hood Gp
| 21***09 | Valve Group-Pilot Relief; -Hydraulic Filter | 1 |
| 33***10 | Hood Group | 1 |
| 5I***70 | Filter-Oil; (Advanced Efficiency)(Hydraulic, Pilot) | 1 |
212-8019 Plate Gp-Frame
| 1A***35 | Bolt 2.00 In. (5.08 cm) Long | 4 |
| 1R***92 | Filter Element As-Oil; (Advanced Efficiency) | 3 |
| 21***19 | Plate Group-Frame | 1 |
235-6512 Step Gp
| 09***21 | Filter-Oil; (Advanced Efficiency)(Hydraulic, Case Drain) | 1 |
| 23***12 | Step Group | 1 |
| 28***95 | Head As-Filter | 1 |
Fuel System
224-5005 Filter Gp-Fuel -Secondary
| 09***25 | Seal-O-Ring (Id=154.30mm) | 1 |
| 14***35 | Connect Group; (Each Includes) | 2 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
174-9570 Filter Gp-Water Sep & Fuel -Primary
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***70 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
293-4071 Injector Gp-Fuel
| 18***38 | Collar | 2 |
| 18***39 | Fan As; (Alternator) | 1 |
| 18***44 | Coil Assem. | 1 |
328-2573 Injector Gp-Fuel
| 12***96 | Pulley-Alternator | 1 |
| 19***41 | Angle Assem. | 1 |
| 19***20 | Alternator Group-Charging; -24-Volt, 95-Ampere | 1 |
216-9868 Lines Gp-Fuel
| 11***22 | Battery Group; (12-Volt, Maintenance Free, Wet) | 2 |
| 12***73 | Cap As-Filler; (Battery) | 6 |
| 20***99 | Clip | 38 |
235-8725 Pump Gp-Filter & Fuel Transfer -Primary
| 23***25 | Pump Group-Filter & Fuel Transfer; -Primary | 1 |
| 6V***22 | Tube-Heat Shrink; (25.4-mm Dia)(10-M) | 0 |
| 7F***60 | Washer | 6 |
267-9720 Pump Gp-Fuel Injection
| 21***37 | Warning Group-Backup | 1 |
| 25***27 | Wiring Group-Hydraulic Tank Fill Pump | 1 |
| 26***91 | Lighting Group-Flood; -Cab Front, Rear, Side, Engine Compartment | 1 |
267-9715 Pump Gp-Fuel Injection
| 10***28 | Spacer-Special; (12.7x26x28.7-mm Thk) | 4 |
| 14***92 | Stud; (M8x1.25-Thd) | 4 |
| 22***73 | Control Group-Engine Electronic | 1 |
256-6915 Pump Gp-Fuel Transfer
| 12***78 | Locknut; (M6x1-Thd) | 2 |
| 25***15 | Pump Group-Fuel Transfer | 1 |
| 26***01 | Sheet As | 1 |
271-2234 Pump Gp-Unit Injector Hyd
| 15***26 | Switch; (Dome Light) | 1 |
| 15***27 | Lamp; (24-Volt)(Dome Light) | 2 |
| 15***28 | Lens; (Dome Light) | 1 |
273-2445 Regulator Gp-Fuel Pressure
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 17***91 | Bracket Assem. | 1 |
| 17***92 | Body Assem. | 1 |
232-0343 Regulator Gp-Fuel Pressure
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 17***91 | Bracket Assem. | 1 |
| 17***92 | Body Assem. | 1 |
269-0681 Tank Gp-Fuel -Auxiliary
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 23***30 | Body As; (Floodlight) | 1 |
Hydraulic System
3g-7232 Bypass Gp-Filter -Hydraulic Oil
| 11***60 | Union | 1 |
| 14***55 | Union As | 6 |
| 15***26 | Union Assembly | 3 |
154-6643 Coupling & Mtg Gp-Pump
| 12***86 | Grommet | 2 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 2 |
| 14***78 | Elbow, 90°,-6 Orb /-6 Orfs; (90°) (-6 Orbx-6orfs) | 2 |
177-2521 Cover Gp-Pump
| 14***53 | Elbow, 45,-6 Orb To-6 Orfs-Drum Clutch Port | 1 |
| 14***55 | Elbow As. | 1 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 1 |
171-2446 Cover Gp-Valve End
| 17***46 | Cover Group-Valve End | 1 |
| 18***30 | Valve Group-Relief; -Swing Motor | 2 |
| 18***75 | Motor Group-Swing | 1 |
327-8141 Cylinder & Mtg Gp-Boom
| 12***54 | Setscrew; (M12x1.75-Thd) | 1 |
| 12***13 | Seal; (Shaft) | 1 |
| 12***14 | Shim; (3-mm Thk) | 1 |
282-3014 Cylinder & Mtg Gp-Boom
| 09***00 | Seal-O-Ring (Id=33.70mm) | 2 |
| 09***33 | Seal-Lip Type | 1 |
| 09***11 | Pin; (Spring) | 2 |
282-3152 Cylinder & Mtg Gp-Saw
| 28***52 | Cylinder & Mtg Group-Saw | 1 |
| 6V***30 | Cap As -Lines From Rotate Valve Work | 5 |
| 6V***32 | Cap As | 4 |
282-3013 Cylinder & Mtg Gp-Stick
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
| 15***44 | Elbow Group | 1 |
| 20***66 | Pump & Motor Group; -Hydraulic Tank Fill | 1 |
282-3109 Cylinder & Mtg Gp-Stick & Saw -Harvester Head, Lh
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 11***68 | Gasket | 1 |
| 20***05 | Seal Kit; (Includes Seal And Rings) | 0 |
248-6874 Cylinder Ar-Hydraulic -Boom, Stick
| 24***74 | Cylinder Ar-Hydraulic; -Boom, Stick | 1 |
| 30***92 | Pump Group-Piston; -Double | 1 |
| 8T***60 | Washer-Hard (For Use With 7/16 In Bolts) | 7 |
217-9701 Cylinder Ar-Hydraulic -Boom, Stick, Saw Tilt
| 10***96 | Screen-Filter | 1 |
| 10***97 | Tube | 1 |
| 10***98 | Tube | 1 |
322-3568 Cylinder Gp-Boom
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 11***17 | Clip | 1 |
| 13***00 | Clip; (Tab) | 3 |
251-8281 Cylinder Gp-Hood Tilt
| 08***01 | Plug As | 3 |
| 09***91 | Ball Bearing | 1 |
| 12***13 | Seal; (Shaft) | 1 |
215-9097 Cylinder Gp-Hydraulic -Boom
| 09***70 | Bolt-Socket Hd; (M12 X 1.75 X 45) | 4 |
| 11***49 | Fitting As; (Quick Disconnect) | 1 |
| 12***85 | Elbow 90 Degree | 1 |
215-9092 Cylinder Gp-Stick -Boom
| 08***01 | Plug As | 3 |
| 09***91 | Ball Bearing | 1 |
| 12***13 | Seal; (Shaft) | 1 |
274-7480 Cylinder Gp-Tilt -Saw
| 19***83 | Rotating Group-Motor; -Travel | 1 |
| 19***86 | Shaft Group-Hydraulic Motor | 1 |
| 27***80 | Cylinder Group-Tilt; -Saw | 1 |
217-9689 Drive Ar-Swing
| 11***19 | Screw-Special; (M5x0.8x8-mm) | 14 |
| 12***29 | Plate-Control | 1 |
| 12***30 | Pin-Center | 1 |
220-8623 Drive Gp-Swing
| 12***87 | Ring-Retaining | 1 |
| 17***91 | Plate; (2.6-mm Thk) | 1 |
| 17***92 | Plate; (2.65-mm Thk) | 1 |
201-7808 Drive Gp-Swing
| 12***87 | Ring-Retaining | 1 |
| 17***87 | Shim; (3.3-mm Thk) | 1 |
| 17***88 | Shim; (3.4-mm Thk) | 1 |
158-8987 Filter & Valve Gp-Pilot -Hydraulic Oil
| 12***87 | Ring-Retaining | 1 |
| 15***87 | Filter & Valve Group-Pilot; -Hydraulic Oil | 1 |
| 17***91 | Plate; (2.6-mm Thk) | 1 |
289-8194 Filter Gp-Oil -Hydraulic, Case Drain
| 28***94 | Filter Group-Oil; -Hydraulic, Case Drain | 1 |
| 4I***63 | Rotor Group-Swivel; (Swivel) | 1 |
222-7092 Filter Gp-Oil -Hydraulic
| 17***02 | Pin | 1 |
| 17***10 | Spring | 4 |
| 17***11 | Plate | 1 |
227-0620 Gauge Gp-Sight -Hydraulic Oil Level
| 1U***46 | Sealant (For Locations A) | 0 |
| 22***20 | Gauge Group-Sight; -Hydraulic Oil Level | 1 |
| 7Y***03 | Rotor | 1 |
192-2892 Head Gp-Motor -Travel
| 09***29 | Ring; (Retaining) | 1 |
| 19***55 | Kit-Bearing | 1 |
| 19***92 | Head Group-Motor; -Travel | 1 |
291-1126 Head Gp-Motor -Travel
| 09***25 | Seal-O-Ring (Id=89.60mm) | 3 |
| 09***16 | Seal-O-Ring (Id=109.40mm) | 1 |
| 14***63 | Seal As | 5 |
308-4488 Head Gp-Pump
| 09***36 | Screw; (Machine) (M5x0.8x10mm) | 5 |
| 09***49 | Bolt; (M8x1.25x40-mm) | 6 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
308-3062 Hydraulic Ar
| 09***43 | Retainer | 1 |
| 12***40 | Connector | 1 |
| 14***39 | Connector As. | 1 |
284-5616 Hydraulic Ar
| 13***01 | Adaptor As | 1 |
| 23***14 | Tube As | 1 |
| 28***16 | Hydraulic Ar | 1 |
282-3068 Hydraulic Ar-Harvester -Without Linkage
| 03***57 | Washer; (13x26x6-mm Thk) | 8 |
| 11***60 | Union | 1 |
| 12***37 | Clip-Loop | 2 |
253-2603 Lines Gp-Boom -Harvester Head
| 09***56 | Setscrew-Socket | 1 |
| 10***04 | Seal-O-Ring | 1 |
| 16***67 | Dowel | 1 |
217-9705 Lines Gp-Boom -Felling Head
| 03***57 | Washer; (13x26x6-mm Thk) | 8 |
| 12***23 | Bracket Assem. | 1 |
| 14***01 | Hose As | 1 |
282-3102 Lines Gp-Front -Boom, Felling Head
| 22***50 | Kit-Control Valve; (Seal)(Control Valve) | 1 |
| 22***51 | Kit-Control Valve; (Mounting Brackets) | 1 |
| 28***02 | Lines Group-Front; -Boom, Felling Head | 1 |
282-3064 Lines Gp-Front -Boom Cylinder, Harvester Head
| 17***00 | Valve Group-Flow Control; (Pilot Supply)(Inlet) | 1 |
| 17***01 | Adapter As-Valve | 1 |
| 17***53 | Fitting-37 Degree | 1 |
253-2604 Lines Gp-Front -Boom, Harvester Head
| 22***44 | Kit-Relief Valve; (Main, Load Sensing) | 1 |
| 22***46 | Kit-Valve | 1 |
| 22***50 | Kit-Control Valve; (Seal)(Control Valve) | 1 |
282-3101 Lines Gp-Front -Boom, Stick
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 17***46 | Cover Group-Valve End | 1 |
282-3065 Lines Gp-Front -Boom, Harvester Head
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 17***46 | Cover Group-Valve End | 1 |
217-9707 Lines Gp-Front -Boom, Felling Head
| 19***94 | Poppet | 1 |
| 19***08 | Spring | 1 |
| 19***81 | Seat | 1 |
317-5827 Lines Gp-Hood Tilt
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 16***43 | Valve Group-Relief; (Control Valve) | 2 |
282-3108 Lines Gp-Motor
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 16***43 | Valve Group-Relief; (Control Valve) | 2 |
285-0933 Lines Gp-Motor
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 17***46 | Cover Group-Valve End | 1 |
272-0058 Lines Gp-Pilot
| 09***41 | Bolt-Socket Head; (M4x0.7x10-mm) | 2 |
| 09***45 | Bolt-Socket Head; (M6x1.00x55mm) | 2 |
| 16***43 | Valve Group-Relief; (Control Valve) | 2 |
282-3071 Lines Gp-Pump
| 11***16 | Kit-Seal; (Counterbalance Valve) | 1 |
| 28***71 | Lines Group-Pump | 1 |
275-7941 Lines Gp-Pump
| 27***41 | Lines Group-Pump | 1 |
217-9692 Lines Gp-Return
| 21***92 | Lines Group-Return | 1 |
| 22***32 | Valve Group-Control; -Inlet | 1 |
| 22***33 | Valve Group-Control; -Accum Arms-Hf, Lo/Hi Flow-Hp-Grapple-Hf, High Flow-Hp | 2 |
217-9709 Lines Gp-Saw
| 12***94 | Plug; (Break Off) | 5 |
| 12***17 | Plug | 1 |
| 15***85 | Dowel | 2 |
253-2607 Lines Gp-Saw
| 08***59 | Setscrew | 2 |
| 12***79 | Piston | 2 |
| 12***80 | Spring | 2 |
256-0350 Lines Gp-Saw
| 08***59 | Setscrew | 2 |
| 12***79 | Piston | 2 |
| 12***81 | Seat | 2 |
253-2602 Lines Gp-Stick
| 12***98 | Seat | 1 |
| 12***99 | Seat | 1 |
| 13***49 | Connector | 1 |
217-9703 Lines Gp-Stick
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 4 |
| 14***07 | Plug; (Hex Head) (-6 Orb) (Current) (16***35 Friction Disc Interchangeable With 11***47) (Use All Of One Part Number) | 2 |
| 1P***02 | Seal-Rectangular 28.83mm(1.136in) Id | 12 |
223-5847 Lines Gp-Travel Motor
| 09***86 | Seal - O-Ring (19.80 mm Id) | 1 |
| 12***14 | Seal-O-Ring (Id=10.82mm) | 1 |
| 12***15 | Seal-O-Ring (Id=12.42mm) | 1 |
281-6404 Motor & Mtg Gp-Swing
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 16***71 | Kit-Seal; (Solenoid Valve) | 1 |
179-9775 Motor Gp-Swing
| 17***85 | Valve Group-Solenoid | 1 |
| 17***75 | Motor Group-Swing | 1 |
| 22***64 | Cartridge As-Valve | 2 |
188-4175 Motor Gp-Swing
| 18***75 | Motor Group-Swing | 1 |
| 24***81 | Flange | 6 |
| 25***37 | Valve Group-Solenoid | 5 |
334-9978 Motor Gp-Swing
| 09***83 | Shim (1.0 mm Thick) | 2 |
| 09***90 | Shim (1.0 mm Thick) | 2 |
| 09***15 | Shim (2.0 mm Thick) | 2 |
334-9971 Motor Gp-Swing
| 09***76 | Seal-O-Ring | 1 |
| 09***86 | Seal - O-Ring (19.80 mm Id) | 1 |
| 09***98 | Seal-O-Ring (Id=29.40mm) | 2 |
279-9872 Motor Gp-Travel
| 09***83 | Shim (1.0 mm Thick) | 2 |
| 09***90 | Shim (1.0 mm Thick) | 2 |
| 09***15 | Shim (2.0 mm Thick) | 2 |
206-6508 Plug Gp-Hydraulic Lines
| 20***08 | Plug Group-Hydraulic Lines | 1 |
| 24***33 | Hose As | 1 |
| 24***34 | Hose As | 1 |
217-9690 Pump & Lines Gp-Hyd Tank Fill
| 21***90 | Pump & Lines Group-Hydraulic Tank Fill | 1 |
| 24***35 | Hose As | 1 |
| 24***36 | Hose As | 1 |
205-5266 Pump & Motor Gp -Hydraulic Tank Fill
| 20***66 | Pump & Motor Group; -Hydraulic Tank Fill | 1 |
| 21***11 | Boom Group | 1 |
| 21***12 | Stick Group; -Felling Head | 1 |
212-8039 Pump & Motor Gp-Hood Tilt
| 21***11 | Boom Group | 1 |
| 21***12 | Stick Group; -Felling Head | 1 |
| 21***14 | Linkage Group-Felling Head | 1 |
308-0093 Pump & Mtg Gp-Main Hydraulic
| 21***97 | Valve & Mtg Group-Main Control; -7-Bank | 1 |
| 22***71 | Control & Mtg Group-Joystick; -Harvester Head | 1 |
| 22***01 | Boom Group | 1 |
283-2529 Pump & Mtg Gp-Saw
| 22***01 | Boom Group | 1 |
| 22***02 | Stick Group; -Harvester Head | 1 |
| 25***02 | Lines Group-Stick | 1 |
308-0092 Pump Gp-Piston -Double
| 12***37 | Clip-Loop | 2 |
| 14***34 | Bolt; (M10x1.5x30-mm) | 1 |
| 21***11 | Boom Group | 1 |
268-8259 Pump Gp-Piston -Saw
| 21***11 | Boom Group | 1 |
| 21***12 | Stick Group; -Felling Head | 1 |
| 21***14 | Linkage Group-Felling Head | 1 |
191-0883 Rotating Gp-Motor -Travel
| 09***83 | Shim (1.0 mm Thick) | 4 |
| 09***15 | Shim (2.0 mm Thick) | 4 |
| 09***34 | Shim; (T=69.85mm) | 2 |
190-8121 Rotating Gp-Motor -Travel
| 09***83 | Shim (1.0 mm Thick) | 2 |
| 09***86 | Shim (1.0mm Thick) | 2 |
| 09***15 | Shim (2.0 mm Thick) | 2 |
283-5979 Rotating Gp-Pump -Main Hydraulic
| 11***48 | Filter Element-Cab Air; (Standard Efficiency) | 1 |
| 24***04 | Air Conditioner Group | 1 |
| 28***79 | Rotating Group-Pump; -Main Hydraulic | 1 |
283-5978 Rotating Gp-Pump -Travel
| 19***99 | Screw-Button Head; (M8x1.25x20-mm) | 2 |
| 24***86 | Plate | 2 |
| 24***97 | Plate | 4 |
283-5977 Rotating Gp-Pump -Implement
| 09***83 | Shim (1.0 mm Thick) | 2 |
| 09***15 | Shim (2.0 mm Thick) | 2 |
| 10***57 | Washer; (22x76.2x6-mm Thk) | 1 |
4i-6262 Rotor Gp-Swivel
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 11***93 | Plate; (Instruction) (On Right Side Behind Cab Door) | 1 |
| 16***43 | Timer As-On Delay; (24-Volt)(Compressor Cycle Limiter) | 1 |
4i-6263 Rotor Gp-Swivel
| 17***63 | Duct As | 1 |
| 19***05 | Gasket | 1 |
| 24***08 | Duct As | 1 |
191-0886 Shaft Gp-Hydraulic Motor
| 03***38 | Clamp | 1 |
| 13***14 | Grommet | 1 |
| 17***87 | Coil As-Heater | 1 |
159-5871 Swivel Gp -Without Tilt Function
| 15***71 | Swivel Group; -Without Tilt Function | 1 |
| 17***25 | Screw-Tapping; (M5x0.8-Thd) | 3 |
| 18***86 | Screw-Machine; (M4x0.7x8-mm) | 2 |
272-0055 Tank Gp-Hydraulic & Fuel
| 19***80 | Guard Group-Window | 1 |
| 23***60 | Plate | 1 |
| 25***94 | Hatch Group-Roof | 1 |
217-9696 Valve & Lines Gp-Travel Cont -Without Tilt Function
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***33 | Switch As-Pressure; (A/C) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
256-0349 Valve & Mtg Gp-Main Control -7-Bank
| 12***35 | Screw; (Truss Head) (M6x1x13mm) | 5 |
| 17***25 | Screw-Tapping; (M5x0.8-Thd) | 3 |
| 23***79 | Nut-Speed | 6 |
285-2268 Valve & Mtg Gp-Main Control -7-Bank
| 10***51 | Loom; (39 cm) | 0 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***08 | Switch As-Limit | 10 |
217-9697 Valve & Mtg Gp-Main Control -7-Bank
| 12***35 | Screw; (Truss Head) (M6x1x13mm) | 4 |
| 18***84 | Cover | 1 |
| 21***97 | Valve & Mtg Group-Main Control; -7-Bank | 1 |
332-0965 Valve Gp-Bank 2
| 11***49 | Pedal Assem.; (L.H.) | 1 |
| 11***50 | Pedal Assem.; (R.H.) | 1 |
| 11***56 | Step Assem. | 2 |
328-1689 Valve Gp-Bank 7
| 22***17 | Harness As-Operator Controls; (Joystick) | 1 |
| 23***22 | Control Group-Handle; -Felling Head | 1 |
| 32***89 | Valve Group-Bank 7 | 1 |
192-3284 Valve Gp-Counterbalance -Travel Motor
| 19***84 | Valve Group-Brake; -Travel Motor | 1 |
| 22***77 | Suspension Group-Seat; -Mechanical | 1 |
| 22***90 | Seat Group; -High Back, Tilt | 1 |
194-6973 Valve Gp-Brake -Pressure Release
| 19***73 | Valve Group-Brake; -Pressure Release | 1 |
| 22***15 | Control Group-Handle; -Harvester Head, Lh | 1 |
| 22***17 | Harness As-Operator Controls; (Joystick) | 1 |
192-3293 Valve Gp-Check & Relief
| 19***93 | Valve Group-Check & Relief; -Travel Motor | 1 |
| 22***16 | Control Group-Handle; -Harvester Head, Rh | 1 |
| 22***17 | Harness As-Operator Controls; (Joystick) | 1 |
242-4240 Valve Gp-Control -Intermittent Saw, 2-Bank
| 10***55 | Cover-Speaker | 2 |
| 11***19 | Bolt-Socket Head; (M4x0.7x25-mm) | 8 |
| 11***54 | Cover | 1 |
227-2133 Valve Gp-Control -Grapple-Hf, High Flow-Hp
| 11***10 | Stud-Ball | 2 |
| 12***70 | Capscrew; (Button Hd) (M8x1.25x20) (G10.9) | 8 |
| 14***06 | Fastener | 15 |
227-2140 Valve Gp-Control
| 22***40 | Valve Group-Control; -Travel | 1 |
| 31***17 | Plate | 2 |
| 31***18 | Plate | 1 |
247-7010 Valve Gp-Control -Saw Motor Control
| 22***90 | Control & Mtg Group-Joystick; -Felling Head | 1 |
| 23***56 | Support Group-Seat | 1 |
| 23***27 | Air Conditioner Group | 1 |
244-7363 Valve Gp-Control -Stick
| 24***63 | Valve Group-Control; -Stick | 1 |
| 26***61 | Foam | 1 |
| 26***62 | Foam | 1 |
234-0587 Valve Gp-Control -Boom
| 17***12 | Cover | 1 |
| 17***13 | Housing | 1 |
| 17***27 | Actuator | 1 |
244-7364 Valve Gp-Control -Lateral Tilt-Hf, Rotator-Hp
| 12***98 | Bracket Assem. | 1 |
| 14***35 | Clip | 1 |
| 16***73 | Valve Group-Shutoff | 2 |
227-2141 Valve Gp-Control -End Cover
| 19***90 | Angle | 1 |
| 19***91 | Guard As | 1 |
| 22***41 | Valve Group-Control; -End Cover | 1 |
227-2135 Valve Gp-Control -Swing
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 2 |
| 11***48 | Filter Element-Cab Air; (Standard Efficiency) | 1 |
| 16***74 | Louver As-Vent | 10 |
325-4351 Valve Gp-Control -Boom
| 13***90 | Bushing; (Radio Mount) | 1 |
| 28***53 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
| 32***51 | Valve Group-Control; -Boom | 1 |
227-2131 Valve Gp-Control
| 22***31 | Valve Group-Control; -Travel | 1 |
| 27***33 | Seal-Washer | 6 |
| 28***70 | Knob | 4 |
218-8376 Valve Gp-Control -Travel, 2-Bank
| 13***92 | Retainer-Captive | 2 |
| 17***33 | Lamp; (Red) | 1 |
| 17***31 | Screw; (Truss Head) (M4x0.7x12mm) | 2 |
338-1090 Valve Gp-Control -Boom
| 33***90 | Valve Group-Control; -Boom | 1 |
| 8S***34 | Locknut; (Flange) (7/16-20 Thd) | 1 |
| 8S***23 | Bolt; (7/16-20x1.5-In) | 1 |
234-0586 Valve Gp-Control -Inlet
| 12***28 | Seal; (17.2-cm Each) | 0 |
| 23***86 | Valve Group-Control; -Inlet | 1 |
| 25***04 | Window-Roof; (Cab) | 1 |
256-0520 Valve Gp-Control -Head Tilt-Hf, Blank-Hp
| 14***81 | Knob-Select; (Radio) | 1 |
| 19***54 | Sleeve | 1 |
| 25***20 | Valve Group-Control; -Head Tilt-Hf, Blank-Hp | 1 |
227-2132 Valve Gp-Control -Inlet
| 09***36 | Screw; (Machine) (M5x0.8x10mm) | 2 |
| 20***05 | Latch As | 1 |
| 22***32 | Valve Group-Control; -Inlet | 1 |
338-1091 Valve Gp-Control -Head Tilt-Hf, Blank-Hp
| 17***59 | Handle; (Lumbar Support Adjuster) | 1 |
| 22***94 | Headrest As-Seat; -Cloth | 1 |
| 24***84 | Kit-Seat; (Handle, Headrest, Lever) | 1 |
227-2137 Valve Gp-Control
| 22***37 | Valve Group-Control; -Felling Head Lateral Tilt | 1 |
| 25***48 | Window; (Center) | 1 |
| 25***50 | Window; (Left) | 1 |
247-9847 Valve Gp-Control -Inlet
| 12***67 | Screw; (M6x1x8-mm) | 3 |
| 13***13 | Bolt; (M10x1.5x16-mm) | 2 |
| 23***70 | Tread | 1 |
333-3729 Valve Gp-Control
| 22***89 | Seat Group-Suspension; -High Back, Tilt | 1 |
| 33***29 | Valve Group-Control | 1 |
| 6V***02 | Bolt-Socket Head; (M8x1.25x16-mm) | 4 |
105-8117 Valve Gp-Counterbalance
| 10***17 | Valve Group-Counterbalance; -Hood Tilt Cylinder | 1 |
| 23***20 | Seat Belt Group; -Retractable, 76-mm | 1 |
| 24***03 | Seat & Mounting Group; -High Back, Tilt | 1 |
291-1122 Valve Gp-Flow Control -Travel Motor
| 23***57 | Support As | 1 |
| 29***22 | Valve Group-Flow Control; -Travel Motor | 1 |
| 7X***29 | Washer; (11x25x3-mm Thk) | 4 |
338-1089 Valve Gp-Main Control -7-Bank
| 19***99 | Screw-Button Head; (M8x1.25x20-mm) | 2 |
| 20***80 | Cylinder-Damper | 1 |
| 24***97 | Plate | 8 |
256-0500 Valve Gp-Main Control -7-Bank
| 14***21 | Kit-Clip; (Seat) | 1 |
| 24***68 | Cover As | 1 |
| 24***89 | Adjuster Group-Seat; -Upper Slide | 1 |
198-3811 Valve Gp-Pump Control -Pressure Compensator-Main Hydraulic
| 12***35 | Screw; (Truss Head) (M6x1x13mm) | 4 |
| 19***11 | Valve Group-Pump Control; -Pressure Compensator-Main Hydraulic | 1 |
| 22***64 | Handle As | 1 |
308-4489 Valve Gp-Pump Control -Pressure Compensator-Main Hydraulic
| 13***30 | Hinge-Lh | 2 |
| 15***15 | Gasket | 1 |
| 19***87 | Frame As-Lower | 1 |
319-7774 Valve Gp-Regeneration
| 09***49 | Bolt; (M8x1.25x40-mm) | 19 |
| 19***92 | Window Group-Cab; -Lh | 1 |
| 19***90 | Angle | 1 |
184-3830 Valve Gp-Relief -Swing Motor
| 09***49 | Bolt; (M8x1.25x40-mm) | 19 |
| 18***30 | Valve Group-Relief; -Swing Motor | 1 |
| 19***92 | Window Group-Cab; -Lh | 1 |
167-1555 Valve Gp-Selector & Press Cont -Pilot Oil Pressure
| 16***55 | Valve Group-Selector & Press Cont; -Pilot Oil Pressure | 1 |
| 19***92 | Window Group-Cab; -Lh | 1 |
| 23***86 | Window; (Left Side, Front, Upper) | 1 |
276-9072 Valve Gp-Shuttle -Signal
| 27***72 | Valve Group-Shuttle; -Signal | 1 |
116-3526 Valve Gp-Solenoid
| 11***26 | Valve Group-Solenoid; -Swing Cushion | 1 |
| 17***03 | Film-Identification; (300-Ft) | 2 |
| 22***17 | Film; (Warning) (Seatbelt) (On Lh Post Inside Cab) | 1 |
171-3685 Valve Gp-Solenoid
| 11***95 | Film-Instruction; (Air Conditioner) | 1 |
| 12***80 | Film-Instruction; (Hydraulic Tank Oil Drain) | 1 |
| 13***59 | Plate-Identification; (Engine Stop, Run) | 1 |
315-4412 Valve Gp-Solenoid
| 31***12 | Valve Group-Solenoid; -Fine Swing | 1 |
195-3739 Valve Gp-Solenoid -Pump Control
| 19***39 | Valve Group-Solenoid; -Pressure Reducing | 1 |
279-6518 Valve Gp-Solenoid & Manifold -Pilot Oil
| 27***18 | Valve Group-Solenoid & Manifold; -Pilot Oil-Reversing Fan | 1 |
222-5781 Valve Gp-Solenoid & Manifold -Disc Saw
| 22***81 | Valve Group-Solenoid & Manifold; -Disc Saw | 1 |
196-5862 Valve Gp-Solenoid & Manifold -Pump Torque Limiter Control
| 19***62 | Valve Group-Solenoid & Manifold; -Pilot Lines-Proportional Reducing | 1 |
322-8716 Valve Gp-Swing Cushion
| 32***16 | Valve Group-Swing Cushion; -Fine Swing | 1 |
158-9090 Valve Gp-Swing Cushion -Fine Swing
| 15***90 | Valve Group-Swing Cushion; -Fine Swing | 1 |
Implements
226-5001 Boom Gp
| 22***01 | Boom Group | 1 |
348-7173 Boom Gp
| 34***73 | Boom Group | 1 |
212-8011 Boom Gp
| 21***11 | Boom Group | 1 |
218-1918 Lines Gp-Grease -Boom
| 21***18 | Lines Group-Grease; -Boom | 1 |
253-2605 Lines Gp-Grease -Boom, Stick
| 25***05 | Lines Group-Grease; -Boom, Stick | 1 |
218-1917 Lines Gp-Grease -Boom, Stick
| 21***17 | Lines Group-Grease; -Boom, Stick | 1 |
282-3069 Linkage Ar-Felling Head
| 28***69 | Linkage Ar-Felling Head | 1 |
212-8010 Linkage Ar-Felling Head
| 21***10 | Linkage Ar-Felling Head | 1 |
252-8713 Linkage Ar-Harvester Head
| 25***13 | Linkage Ar-Harvester Head | 1 |
282-3012 Linkage Ar-Harvester Head
| 28***12 | Linkage Ar-Harvester Head | 1 |
252-8717 Linkage Ar-Intermittent Saw
| 25***17 | Linkage Ar-Intermittent Saw | 1 |
284-5617 Linkage Ar-Intermittent Saw
| 28***17 | Linkage Ar-Intermittent Saw | 1 |
212-8014 Linkage Gp-Felling Head
| 21***14 | Linkage Group-Felling Head | 1 |
226-5002 Stick Gp -Harvester Head
| 22***02 | Stick Group; -Harvester Head | 1 |
212-8012 Stick Gp -Felling Head
| 21***12 | Stick Group; -Felling Head | 1 |
347-6972 Stick Gp
| 34***72 | Stick Group | 1 |
Lubrication System
220-1998 Filter Gp-Engine Oil
| 03***34 | Seal-O-Ring | 1 |
| 19***52 | Gasket | 1 |
| 20***82 | Bolt; (M8x1.25x25-mm) | 2 |
226-3559 Fumes Disposal Gp
| 18***99 | Connector As | 1 |
| 18***04 | Elbow As; (90 Degree) | 1 |
| 19***19 | Gasket; (Coated Metal) | 1 |
219-9960 Gauge Gp-Oil Level (Dipstick) -Engine
| 21***22 | Pump As-Engine Oil | 1 |
| 21***46 | Gerotor Pump Group | 1 |
| 21***60 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
202-6603 Lines Gp-Engine Oil
| 20***03 | Lines Group-Engine Oil | 1 |
| 20***93 | Gasket | 1 |
| 29***67 | Core As-Oil Cooler; (Engine) | 1 |
165-4465 Lines Gp-Turbocharger Oil
| 16***65 | Lines Group-Turbocharger Oil | 1 |
| 21***62 | Radiator & Mounting Group | 1 |
| 21***63 | Lines Group-Cooling; -Rad, Aftercooler, Hydraulic Cooler | 1 |
195-8098 Pump Gp-Engine Oil
| 14***38 | Adapter, -6 Orb / Orfs X-Long | 2 |
| 14***69 | Adapter; (90° Elbow Orfs/Orb) | 2 |
| 16***70 | Connector As | 2 |
Machine Arrangement
272-0051 Chassis Ar
| 21***00 | Installation Ar-Engine | 1 |
| 21***60 | Cooling Ar | 1 |
| 26***76 | Undercarriage Ar | 1 |
328-4394 Common Ar
| 11***86 | Flywheel Group | 1 |
| 11***94 | Fastener Group-Flywheel; (Flywheel) | 1 |
| 11***27 | Cover Group-Front Housing; -Accessory Drive | 1 |
242-5335 Conversion Ar-Machine -Without Front Linkage
| 16***48 | Crankshaft Group | 1 |
| 18***26 | Cooler Group-Engine Oil | 1 |
| 19***98 | Pump Group-Engine Oil; (Engine Oil) | 1 |
Operator Station
245-7896 Adjuster Gp-Seat -Lower Slide
| 24***96 | Adjuster Group-Seat; -Lower Slide | 1 |
245-7889 Adjuster Gp-Seat -Upper Slide
| 24***89 | Adjuster Group-Seat; -Upper Slide | 1 |
243-6303 Air Conditioner & Mounting Gp
| 24***03 | Air Conditioner & Mounting Group | 1 |
243-6304 Air Conditioner Gp
| 24***04 | Air Conditioner Group | 1 |
250-0398 Air Conditioner Gp
| 25***98 | Air Conditioner Group | 1 |
238-1027 Air Conditioner Gp
| 23***27 | Air Conditioner Group | 1 |
259-7347 Armrest Gp -Lh
| 25***47 | Armrest Group; -Lh | 1 |
259-7346 Armrest Gp -Rh
| 25***46 | Armrest Group; -Rh | 1 |
320-7458 Cab Gp-Enclosed Rops
| 32***58 | Cab Group-Enclosed Rops | 1 |
320-7457 Cab Gp-Enclosed Rops
| 32***57 | Cab Group-Enclosed Rops | 1 |
246-7154 Case Gp-Air Conditioner
| 24***54 | Case Group-Air Conditioner | 1 |
226-3561 Compressor Gp-Refrigerant
| 22***61 | Compressor Group-Refrigerant | 1 |
259-7349 Console Gp-Operator -Lh
| 25***49 | Console Group-Operator; -Lh | 1 |
259-7348 Console Gp-Operator -Rh
| 25***48 | Console Group-Operator; -Rh | 1 |
243-5686 Console Gp-Operator
| 24***86 | Console Group-Operator | 1 |
224-4990 Control & Mtg Gp-Joystick -Felling Head
| 22***90 | Control & Mtg Group-Joystick; -Felling Head | 1 |
223-0671 Control & Mtg Gp-Joystick -Harvester Head
| 22***71 | Control & Mtg Group-Joystick; -Harvester Head | 1 |
238-8167 Control & Mtg Gp-Pedal
| 23***67 | Control & Mtg Group-Pedal | 1 |
223-0715 Control Gp-Handle -Harvester Head, Lh
| 22***15 | Control Group-Handle; -Harvester Head, Lh | 1 |
223-0716 Control Gp-Handle -Harvester Head, Rh
| 22***16 | Control Group-Handle; -Harvester Head, Rh | 1 |
235-4122 Control Gp-Handle -Felling Head
| 23***22 | Control Group-Handle; -Felling Head | 1 |
231-2613 Control Gp-Hydraulic Pedal
| 23***13 | Control Group-Hydraulic Pedal | 1 |
283-2395 Control Gp-Joystick -Harvester Head, Rh
| 28***95 | Control Group-Joystick; -Harvester Head, Rh | 1 |
283-2394 Control Gp-Joystick -Harvester Head, Lh
| 28***94 | Control Group-Joystick; -Harvester Head, Lh | 1 |
283-2393 Control Gp-Joystick -Felling Head
| 28***93 | Control Group-Joystick; -Felling Head | 1 |
319-6719 Control Gp-Monitor -Iqan
| 31***19 | Control Group-Monitor; -Iqan | 1 |
298-1567 Door Gp-Access -Cab Roof
| 29***67 | Door Group-Access; -Cab Roof | 1 |
256-1296 Door Gp-Access -Cab Roof
| 25***96 | Door Group-Access; -Cab Roof | 1 |
320-7459 Door Gp-Access -Cab Air Filter
| 32***59 | Door Group-Access; -Cab Air Filter | 1 |
334-1077 Door Gp-Cab
| 33***77 | Door Group-Cab | 1 |
282-2679 Door Gp-Cab
| 28***79 | Door Group-Cab | 1 |
239-1378 Duct Gp-Cab Air
| 23***78 | Duct Group-Air | 1 |
321-3821 Frame Gp-Window
| 32***21 | Frame Group-Window | 1 |
258-0699 Frame Gp-Window -Thick Glass
| 25***99 | Frame Group-Window; -Thick Glass | 1 |
197-9880 Guard Gp-Window
| 19***80 | Guard Group-Window | 1 |
253-9594 Hatch Gp-Roof
| 25***94 | Hatch Group-Roof | 1 |
323-2220 Hatch Gp-Roof
| 32***20 | Hatch Group-Roof | 1 |
329-5158 Hatch Gp-Roof
| 32***58 | Hatch Group-Roof | 1 |
251-6761 Housing Gp-Air Conditioner -Outlet Air
| 25***61 | Housing Group-Air Conditioner; -Outlet Air | 1 |
238-5024 Installation Gp-Radio
| 23***24 | Installation Group-Radio | 1 |
340-5084 Liner Gp-Cab
| 34***84 | Liner Group-Cab | 1 |
325-8562 Liner Gp-Cab
| 32***62 | Liner Group-Cab | 1 |
261-1090 Lines Gp-Air Conditioner
| 26***90 | Lines Group-Air Conditioner | 1 |
251-6137 Mounting Gp-Cab
| 25***37 | Mounting Group-Cab | 1 |
282-2698 Operator Ar
| 28***98 | Operator Ar | 1 |
238-5020 Platform Gp-Operator
| 23***20 | Platform Group-Operator | 1 |
285-2371 Radio Gp -Am/Fm Cassette, Cd Changer
| 28***71 | Return Pipe, Radio Group; -Am/Fm Cassette, Cd Changer | 1 |
349-7701 Radio Gp -Am/Fm/Wb/Cd
| 34***01 | Radio Group; -Am/Fm/Wb/Cd | 1 |
284-8953 Radio Gp -Am/Fm/Wb/Cd Player
| 28***53 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
240-5003 Seat & Mounting Gp -High Back, Tilt
| 24***03 | Seat & Mounting Group; -High Back, Tilt | 1 |
240-5061 Seat & Mounting Gp -Air Susp, High Back, Tilt
| 24***61 | Seat & Mounting Group; -Air Susp, High Back, Tilt | 1 |
235-9020 Seat Belt Gp -Retractable, 3-In
| 23***20 | Seat Belt Group; -Retractable, 76-mm | 1 |
240-5039 Seat Belt Gp
| 24***39 | Seat Belt Group; -Retractable, 76-mm | 1 |
242-3122 Seat & Mounting Gp -High Back, Tilt
| 24***22 | Seat Group; -High Back, Tilt | 1 |
229-9090 Seat Gp -High Back, Tilt
| 22***90 | Seat Group; -High Back, Tilt | 1 |
240-5062 Seat Gp-Suspension -Air Susp, High Back, Tilt
| 24***62 | Seat Group-Suspension; -Air Susp, High Back, Tilt | 1 |
229-9089 Seat Gp-Suspension -High Back, Tilt
| 22***89 | Seat Group-Suspension; -High Back, Tilt | 1 |
235-8856 Support Gp-Seat
| 23***56 | Support Group-Seat | 1 |
245-7892 Suspension Gp-Seat
| 24***92 | Suspension Group-Seat; -Mechanical | 1 |
229-9077 Suspension Gp-Seat
| 22***77 | Suspension Group-Seat; -Mechanical | 1 |
273-5384 Suspension Gp-Seat -Air
| 27***84 | Suspension Group-Seat; -Air | 1 |
240-5063 Suspension Gp-Seat -Air
| 24***63 | Protector, Suspension Group-Seat; -Air | 1 |
340-5085 Trim Gp-Cab
| 34***85 | Trim Group-Cab | 1 |
320-7473 Trim Gp-Cab
| 32***73 | Trim Group-Cab | 1 |
196-2392 Window Gp-Cab -Lh
| 19***92 | Window Group-Cab; -Lh | 1 |
313-3545 Window Gp-Cab -Lh
| 31***45 | Window Group-Cab; -Lh | 1 |
321-3822 Window Gp-Cab
| 32***22 | Window Group-Cab | 1 |
317-3155 Window Gp-Cab -Lh
| 31***55 | Window Group-Cab; -Lh | 1 |
Power Train
279-9868 Final Drive Gp
| 26***24 | Link As-Track; -Grease Lubricated Track-Positive Pin Retention | 1 |
| 27***68 | Final Drive Group | 1 |
| 29***67 | Pin-Track | 1 |
192-5568 Drive Gp-Final
| 19***68 | Final Drive Group | 1 |
| 26***24 | Link As-Track; -Grease Lubricated Track-Positive Pin Retention | 1 |
| 29***67 | Pin-Track | 1 |
7y-0369 Sprocket Gp
| 22***04 | Roller Group-Track-Single Flange | 6 |
| 26***25 | Track Group | 2 |
| 7X***65 | Bolt; (M20x2.5x100-mm) | 24 |
Service Equipment And Supplies
259-1068 Film-Instruction -Joystick Control, Pattern 1
| 25***68 | Film-Instruction; -Joystick Control, Pattern 1 | 1 |
318-9005 Plate & Film Gp
| 31***05 | Plate & Film Group | 1 |
228-9470 Plate & Film Gp -English
| 22***70 | Plate & Film Group; -English | 1 |
285-5316 Plate & Film Gp
| 28***16 | Plate & Film Group | 1 |
Undercarriage
1c-9474 Fastener Gp-Carbody
| 08***59 | Plug As | 1 |
| 09***32 | Bolt-Socket Head; (M12x1.75x95-mm) | 2 |
| 09***04 | Bolt-Socket Head; (M12x1.75x110-mm) | 4 |
262-7782 Frame Gp-Undercarriage
| 12***94 | Plug; (Break Off) | 1 |
| 12***17 | Plug | 1 |
| 12***62 | Seal-O-Ring | 2 |
115-6417 Idler Gp-Front
| 11***17 | Idler Group-Front; (Front) (B) | 1 |
| 21***89 | Drive Ar-Swing | 1 |
| 21***90 | Pump & Lines Group-Hydraulic Tank Fill | 1 |
115-3696 Idler Gp-Front
| 11***96 | Idler Group-Front; (Front) (C) | 1 |
| 12***94 | Plug; (Break Off) | 1 |
| 12***17 | Plug | 1 |
115-6409 Idler Gp-Front
| 11***09 | Idler Group-Front | 1 |
| 21***00 | Pump & Mtg Group-Main Hydraulic; -Felling Head | 1 |
| 25***50 | Lines Group-Saw | 1 |
261-1024 Link As-Track -Grease Lubricated Track
| 21***97 | Valve & Mtg Group-Main Control; -7-Bank | 1 |
| 22***71 | Control & Mtg Group-Joystick; -Harvester Head | 1 |
| 26***24 | Link As-Track; -Grease Lubricated Track-Positive Pin Retention | 1 |
262-7785 Roller Ar-Track
| 14***55 | Union As | 22 |
| 15***26 | Union Assembly | 2 |
| 20***29 | Tag-Identification; (Saw Oil Drain) | 2 |
206-1263 Roller Gp-Track-Double Flange
| 11***60 | Union | 1 |
| 14***55 | Union As | 8 |
| 15***26 | Union Assembly | 4 |
247-0565 Roller Gp-Track-Single Flange
| 03***57 | Washer; (13x26x6-mm Thk) | 4 |
| 10***77 | Bolt-Socket Head; (M10x1.5x45-mm) | 4 |
| 15***62 | Union As | 1 |
228-6404 Roller Gp-Track-Single Flange
| 03***57 | Washer; (13x26x6-mm Thk) | 4 |
| 10***77 | Bolt-Socket Head; (M10x1.5x45-mm) | 4 |
| 14***27 | Connector Group | 3 |
206-1264 Roller Gp-Track-Single Flange
| 20***64 | Roller Group-Track-Single Flange | 1 |
| 28***01 | Lines Group-Front; -Boom, Stick | 1 |
| 28***02 | Lines Group-Front; -Boom, Felling Head | 1 |
101-7875 Spring Gp-Recoil
| 10***75 | Spring Group-Recoil | 1 |
| 14***27 | Connector Group | 3 |
| 14***31 | Tee Group | 1 |
102-8109 Adjustment Gp-Hydraulic Track
| 09***19 | Seal-O-Ring (Id=15.80mm) | 4 |
| 10***09 | Track Adjuster Group | 1 |
| 23***57 | Pipe | 1 |
288-6320 Track Ar -Single Flange
| 10***77 | Bolt-Socket Head; (M10x1.5x45-mm) | 4 |
| 15***62 | Union As | 1 |
| 1P***02 | Seal-Rectangular 28.83mm(1.136in) Id | 13 |
262-7621 Track Gp
| 14***55 | Union As | 8 |
| 20***27 | Tag-Identification; (Saw Oil Supply) | 8 |
| 20***28 | Tag-Identification; (Saw Oil Return) | 8 |
290-2271 Track Gp -Rh
| 11***60 | Union | 1 |
| 14***55 | Union As | 4 |
| 15***26 | Union Assembly | 4 |
290-2272 Track Gp -Lh
| 09***49 | Bolt; (M8x1.25x40-mm) | 2 |
| 11***65 | Bracket | 1 |
| 12***50 | Valve-Check; (Quick Coupler Solenoid) | 1 |
261-1026 Track Gp
| 14***25 | Connector As. | 2 |
| 14***68 | Elbow Group | 1 |
| 15***33 | Elbow, 45°,-6 Orb /-4 Orfs | 1 |
261-1025 Track Gp
| 20***30 | Tag-Identification; (Aa Head) | 2 |
| 20***31 | Tag-Identification; (Aa Rod) | 2 |
| 20***32 | Tag-Identification; (Ga Head) | 2 |
262-7280 Undercarriage Ar
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 11***17 | Clip | 1 |
| 13***00 | Clip; (Tab) | 3 |
262-7776 Undercarriage Ar
| 14***18 | Reducer; (-8orfs/-12orfs Swivel) | 5 |
| 14***55 | Union As | 14 |
| 15***26 | Union Assembly | 1 |
262-7278 Undercarriage Ar
| 26***78 | Undercarriage Ar | 1 |
| 28***71 | Lines Group-Pump | 1 |
| 28***08 | Lines Group-Motor | 1 |
262-7275 Undercarriage Ar
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 11***17 | Clip | 1 |
| 13***00 | Clip; (Tab) | 3 |
262-7276 Undercarriage Ar
| 11***34 | Tee-O-Ring | 1 |
| 14***28 | Connector Assem. | 1 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
262-7279 Undercarriage Ar
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 11***17 | Clip | 1 |
| 13***00 | Clip; (Tab) | 3 |
262-7274 Undercarriage Ar
| 10***02 | Bolt-Socket Head; (M12x1.75x30-mm) | 2 |
| 10***19 | Bolt; (Socket Head) (M12x1.75x70mm) | 2 |
| 14***47 | Elbow; (-12 Orb/Orfs) | 1 |
Frequently asked questions
What engine powers the Caterpillar 2290?
Public spec sheets don't confirm a specific engine model for the 2290. It comes from the Prentice/Blount International track carrier family, which ran Caterpillar diesel power across its lineup, but the exact engine model and rated horsepower fitted to a given 2290 depends on its build date and configuration. Check the engine data plate or run the serial number through a Cat dealer parts lookup to confirm the exact powerplant.
What is the operating weight of the Caterpillar 2290?
No published factory spec sheet lists an operating weight for the 2290. Based on its place in the 1090-2590 tracked carrier family and its felling-head configuration, it falls in the mid-to-heavy tracked feller buncher class, but exact weight varies by undercarriage, felling head, and counterweight configuration. Treat any weight figure for this model as an estimate until confirmed against the machine's data plate.
What replaced the Caterpillar 2290?
Caterpillar's 500-series Zero Tail Swing track feller bunchers, including the 511, 521/522, and 532, superseded the old Blount-era numeric line around 2011. These successors share undercarriage, swing bearing, and hydraulic pump lineage with the 2290 family but added updated ACERT engines and emissions compliance the earlier machines lacked.
What 2290 owners discuss
What exactly is the Caterpillar 2290, and where does it sit in Cat's forestry lineup?
The 2290 is a track-mounted feller buncher, not a wheeled or knuckleboom machine. It carries a Prentice/Blount heritage design that Caterpillar picked up and continued cataloging under its own forestry parts system after taking over Blount's forestry division in the mid-2000s. It sits in a broad family of similarly numbered track feller bunchers spanning roughly the 1090 through 2590T range, all sharing common running gear and hydraulic architecture from that era. Dealers list the 2290 as a non-current model today, meaning it is long out of production and supported only through the legacy Prentice/Cat forestry parts network rather than active new-machine channels. Exact size class and options vary by configuration and build year, so confirm the specific spec plate against the parts lookup before ordering anything.
What engine is in the 2290, and are there known quirks with it?
Machines in this Prentice/Blount-derived Cat forestry family are consistently described as running Caterpillar diesel engines, but the exact engine model fitted to a given 2290 is not consistently documented across dealer and parts references — it varies by build year and configuration, so read the engine tag rather than assume. For the mechanical-injection Cat diesels common in forestry equipment of this vintage, the recurring gripes are air getting into the fuel system after filter changes (needs a proper bleed procedure, not just cranking it over) and turbo/aftercooler fouling from sawdust and slash debris packing into the engine bay, which shows up as gradual power loss and rising coolant/oil temps if the bay isn't blown out regularly. Have your dealer verify the exact engine family and injection type from the serial/engine plate before ordering fuel system parts.
What hydraulic and powertrain behaviors are typical for this class of machine?
Cat carried a fairly standardized axial piston pump design across multiple generations of its track feller bunchers, from the older 1090/1290-class machines through later models, so the pump troubleshooting playbook is consistent across the family: a whine under load, sluggish boom response, or hydraulic oil that runs hotter than normal all point to pump wear or a starved supply line rather than something exotic. The felling head circuit is the most demanding part of the system. Disc saw heads need a dedicated pump circuit sized and pressure-tuned correctly, or the blade bogs down, loses flywheel momentum, and struggles to finish a cut — setup of saw drive pressures is described as touchy and easy to get wrong. Shear heads are simpler, lower-maintenance, and more forgiving but cut more slowly. Hydraulic cooling capacity is a recurring limiting factor in hot climates or heavy duty cycles, so a marginal cooler is often the real cause of a machine that feels underpowered.
What undercarriage and wear patterns should owners expect?
Track feller bunchers chew through undercarriage faster than a comparable excavator because the machine is constantly pivoting and counter-rotating over stumps, slash, and uneven ground rather than just tramming. General consensus for this equipment class: run with the idler forward whenever the job allows, since traveling in reverse puts the full tractive load on the top run of chain and roughly doubles the pin-and-bushing wear cycle. Keep track tension set for the specific ground conditions — just tight enough that the sprocket doesn't jump. Run the narrowest track shoe that still gives adequate flotation, because wider shoes shorten sprocket, roller, and idler life. A quick field check operators use: if the idler mounting bracket is visibly standing proud of the roller frame, pin-and-bushing wear is advanced and chain failure isn't far off.
What electrical or sensor problems come up on machines like this?
Specific fault data for the 2290 by name is thin, so this reflects the broader pattern seen across Cat-era forestry equipment of similar vintage and configuration. Wiring harnesses take a beating at the boom pivot points and at the felling head wrist joint from constant flexing, leading to intermittent grounds and chafed insulation over time. Connectors corrode where the machine gets washed down with high-pressure water and sap/pitch contamination works into the pins. Saw or clutch engagement sensors are a known nuisance point — vibration knocks them out of calibration or kills them outright, showing up as erratic head engagement. Because this is an older, low-volume platform, treat any sensor diagnosis as a case of confirm-with-a-multimeter first rather than assuming a factory fault code will point straight at it, and have your dealer verify wiring diagrams against the actual serial-number build before replacing components.
What should a buyer check before purchasing a used 2290?
First, confirm parts support and lead time before committing — this is a discontinued, non-current model supported through the legacy Prentice/Cat forestry parts network, so replacement lead times can run long compared to a current-production machine. On the physical inspection, follow the same checklist experienced buyers use for any used track feller buncher: inspect the felling head closely (saw disc for cracks or warping, or shear blade edge wear if shear-equipped), check swing bearing play and rotation smoothness for roughness or excess backlash, check every boom and arm pin/bushing for slop, look for cylinder rod scoring and test for cylinder drift under load, listen for pump noise or cavitation under full boom extension, and assess undercarriage condition (chain sag, sprocket tooth wear, idler wear) rather than trusting the hour meter alone. Run the machine through a full load cycle — boom, swing, and felling head together — before final offer, and have your dealer verify the hydraulic pump condition and undercarriage wear percentage as part of a pre-purchase inspection.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 2290 part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.