Caterpillarmotor grader
Caterpillar 16H
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 16H is a large-frame, articulated motor grader built for mine haul-road maintenance and large-scale earthmoving, sitting at the top of Cat's H-series grader range. It runs a direct-drive power shift transmission with eight forward and eight reverse speeds into planetary final drives, load-sensing hydraulics, and air-over-hydraulic brakes. Two engines appear under the 16H name: the standard configuration carries a Cat 3196 ETA, turbocharged and air-to-air aftercooled 11.9 L inline-six rated about 197-213 kW (265-285 hp) depending on gear range, while the heavier 16H ES / Standard Mining configuration carries a larger Cat 3406 DITA 14.6 L inline-six rated around 205 kW (275 hp). Operating weight runs from about 24.7 tonnes (54,550-54,560 lb) standard up to roughly 31.6 tonnes (69,648 lb) in maximum ballast trim, carrying a 4.88-4.91 m (16-16.1 ft) moldboard. Cat built the 16H from the mid-1990s to around 2006-2007, replacing the 16G (1987-1995) and itself being replaced by the 16M when Cat's M-series joystick-controlled graders launched.
The two engine options were likely not simultaneous trims so much as a running change: available serial and production records place the 3406-powered run earlier in the 16H's production life and the 3196-powered run later, alongside factory mining-spec guarding (front axle cylinder, line, and fitting guards, plus a transmission underguard) and standard ether starting aimed at haul-road duty. Compared to the 16G it replaced, the 16H added updated engine, hydraulic, and electronic-monitoring packages, including real CID/FMI diagnostic fault codes in place of purely mechanical gauges; it then gave way to the 16M's joystick steering and Cat C13 ACERT power. In the used and parts market, the 16H still matters because it remains one of the largest mechanically-steered Cat graders active in mining and heavy-civil fleets. Its circle drive, tandems, and engine are common enough across surviving units that dealer parts support and dismantled-unit sourcing both stay workable, even though Cat has since moved current mining-grader production to newer platforms.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 16H specifications
Engine
| Engine model (standard configuration) | Cat 3196 ETA, turbocharged and air-to-air aftercooled (ATAAC), 6-cylinder inline diesel |
| Displacement (3196 engine) | 11.9 L (726 cu in) |
| Net power (3196 engine, by gear range) | 197 kW (265 hp) in gears 1-2; up to 213 kW (285 hp) in gears 4 through 8, rated at 2000 rpm |
| Net torque (3196 engine, gears 7-8) | 1550 Nm (1143 lb-ft) |
| Engine model (16H ES / Standard Mining configuration) | Cat 3406 TA / DITA, 6-cylinder inline diesel, turbocharged |
| Displacement (3406 engine) | 14.6 L (891 cu in) |
| Net power (3406 engine, all gears) | 205 kW (275 hp) at 1850 rpm |
| Gross power | Not published separately on available spec sheets; only net flywheel power by gear range is documented for this model |
| Emissions tier | Not documented on available spec sheets for this generation. Production spans roughly the mid-1990s to mid-2000s, predating widely published EPA/EU nonroad tier listings for this model |
| Series/generation note | 16H is part of Cat's H-series motor grader line. The base 16H uses the 3196 engine, while the 16H ES / Standard Mining variant uses the larger 3406 engine. Later succeeded by the 16M series |
Weights
| Operating weight, standard (3196 configuration) | 24,740 kg (54,550 lb) total - front axle 6,984 kg (15,397 lb), rear axle 17,760 kg (39,153 lb) |
| Operating weight, typically equipped (16H ES / Standard Mining, 3406 configuration) | 24,748 kg (54,560 lb) |
| Maximum operating weight, ballasted (3196 configuration) | 31,592 kg (69,648 lb) total - front axle 8,847 kg (19,502 lb), rear axle 22,746 kg (50,146 lb) |
| Shipping weight | Not separately published; dealer spec sheets list operating weight only |
| Ground pressure | Not published in available spec sheets |
Dimensions
| Overall length | 9.99-10.0 m (32.8 ft), both engine configurations |
| Width over tires | 3.08 m (10.1 ft) |
| Height to top of cab | 3.52 m (11.6 ft) standard cab; Standard Mining configuration measured at 3.75 m (12.3 ft) - varies by cab/canopy configuration |
| Wheelbase | 6.96-6.98 m (22.8-22.9 ft) |
| Tandem wheelbase | 1.83 m (6.0 ft) |
| Front ground clearance | 0.73 m (2.4 ft) |
| Rear ground clearance | 0.41-0.43 m (1.34-1.4 ft), minor variance by source |
| Moldboard/blade width | 4.88 m (16 ft) standard; 4.91 m (16.1 ft) on ES configuration |
| Moldboard height | 787 mm (31 in) |
Performance
| Max travel speed forward | 48.1 km/h (29.9 mph) with 3196 engine; 44.5 km/h (27.7 mph) with 3406 engine (ES/Standard Mining configuration) |
| Max travel speed reverse | 45.7 km/h (28.4 mph) with 3196 engine; 42.3 km/h (26.3 mph) with 3406 engine (ES/Standard Mining configuration) |
| Transmission | Power-shift, 8 forward / 8 reverse speeds, with inching pedal |
| Turning radius (outside front tires) | 8.2 m (27 ft) |
| Articulation angle | 20 degrees |
| Max blade pull at max operating weight | approx. 200.7 kN (45,131 lb) |
| Blade down pressure | approx. 155.2 kN (34,901 lb) |
| Max depth of cut | 470 mm (18.5 in) |
| Max blade lift above ground | 419 mm (16.5 in) |
| Gradeability | Not published in available spec sheets |
Service capacities (summary)
| Fuel tank | 492 L (130 gal US), both configurations |
| Hydraulic system | 129-130 L (34-34.4 gal US) |
| Engine oil (with filter) | approx. 34-38 L (9-10 gal US), varies by engine (3196 vs 3406) |
| Cooling system | 46.5 L (12.3 gal US) with 3196 engine; 64 L (16.9 gal US) with 3406 engine (ES/Standard Mining configuration) |
| Final drive / tandem housings (each) | approx. 119 L (31.5 gal US) per tandem case; rear differential/final drive approx. 114 L (30.1 gal US) |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
16H fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | 38 L (10.0 US gal) | Cat DEO (Diesel Engine Oil) for the Cat 3406-family engine fitted to the 16H. SAE 15W-40 for temperate/warm ambient temperatures; SAE 10W-30 in cooler climates, per Cat's ambient-temperature viscosity guidance. |
| Cooling system | 46.5 L (12.3 US gal) per most spec sheets; one lubricant-fitment source lists 59 L (15.6 US gal) — varies by configuration/series | Cat ELC (Extended Life Coolant) or Cat DEAC, factory premix / 50-50 concentration. Extended-life formulation extends drain interval versus conventional antifreeze. |
| Fuel tank | 492 L (130.0 US gal) | Diesel fuel meeting Cat's fuel specification. No. 2-D grade for normal ambient; No. 1-D or a winter blend for cold-weather starting. |
| Transmission and differential (combined power-train compartment) | 114 L (30.1 US gal) | Cat TDTO (Transmission/Drive Train Oil). SAE 10W in cold climates, SAE 30 in moderate climates, SAE 50 in hot climates, per Cat's ambient-temperature viscosity chart for TO-4 compartments. |
| Tandem drive housings, each side (final drive) | 119-122 L (31.5-32.2 US gal) per side, figures vary slightly by source | Cat TDTO, same climate-based viscosity selection as the power-train compartment (SAE 10W / 30 / 50). |
| Circle drive gearbox | 8 L (2.1 US gal) | Cat TDTO, or an equivalent GL-5 gear lubricant, for the circle-drive housing. |
| Hydraulic tank (refill) | 55 L (14.5 US gal) | Cat TDTO SAE10W as the shared implement/steering hydraulic fluid, or Cat HYDO Advanced 10W equivalent. |
| Hydraulic system, total (tank plus lines and cylinders) | 129 L (34.0 US gal) | Same fluid as the hydraulic tank — Cat TDTO SAE10W / Cat HYDO Advanced 10W. |
| Front wheel spindle bearing cavity, each wheel | 0.9 L (0.24 US gal) per wheel | Cat multipurpose grease, NLGI 2, packed at scheduled spindle-bearing service. |
| Grease points (circle drive, drawbar, blade-lift and other pins) — spec only, no reservoir capacity | n/a — serviced per grease-point interval, not a fill reservoir | Cat multipurpose EP grease such as Cat Ultra Multipurpose Grease or Cat Advanced 3Moly Grease, NLGI 2, for pin and circle-drive lubrication points. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 16H maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 4,000 h |
|
| Every 6,000 h |
|
Servicing the 16H beyond the schedule
Predictive Maintenance & Fluid Analysis
Sample engine, transmission, differential, tandem, and circle drive gearbox oil on a fixed interval - all are shimmed or gear-driven compartments where slow leaks and worn wear metals show up in analysis long before failure. Because the axial-piston load-sensing hydraulic pump and PPPC valves are contamination-sensitive, treat hydraulic oil cleanliness as a leading indicator, not an afterthought. Listen for a whining or knocking steering cushion valve at full lock each direction, and log compressor cut-in/cut-out air pressures - both are documented early-warning signs on this machine before a costly failure.
Corrective & Common Repairs
The circle drive slip clutch is the 16H's signature wear item: it should slip under shock load so a buried rock or curb strike doesn't transfer into the drawbar, circle, and A-frame. A seized or over-tightened pack risks a broken shaft on the next hit. Expect circle tooth and pinion-mesh wear, plus worn drawbar/circle wear strips needing shimming or replacement. Cracks or welds on the circle casting or A-frame usually trace back to a clutch that wasn't slipping. Chafed harness at the articulation joint often causes intermittent fault codes.
Overhaul & Rebuild Points
Major rebuild points follow the drivetrain the 16H actually carries: the 3196 or 3406 engine top end, the power shift transmission's clutch packs across its eight forward/reverse speeds, and the tandem final-drive gearing that takes the brunt of haul-road load. Circle gear and pinion mesh open up over time and are a common in-frame rebuild alongside the slip clutch pack. Check front wheel king pins and radius arms for play, and inspect the articulation joint, since a worn joint shows up as the frame no longer tracking straight.
Seasonal & Environment Servicing
The 16H's mining-configuration factory guarding - front axle cylinder, line, and fitting guards, plus a transmission underguard - exists because haul-road duty throws rock and debris at the underside; inspect and replace guarding rather than running without it. Ether starting is standard for cold starts on either engine, so check the cylinder charge before winter. In dusty pit environments, shorten air filter and circle/tandem breather service, and wash packed mud from drawbar wear strips and the articulation joint often, since trapped grit accelerates wear already inherent under haul-road load.
16H common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1R-0762 | Filter As-Fuel | Fuel system service | Check fitment → |
| 129-0375 | Bowl As-Water Collection | Fuel system service | Check fitment → |
| 133-5673 | Element | Fuel system service | Check fitment → |
| 203-2423 | Kit-Heating Element | Air intake service | Check fitment → |
| 231-4486 | Filter Element As-Cab Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
16H fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| CID 0110 - FMI 03 | Engine coolant temperature sensor: voltage above normal (open circuit or short to a higher-voltage source) | Disconnected or corroded sensor connector, open signal wire, or failed coolant temp sensor | Check the sensor connector and harness for an open circuit, verify sensor resistance against spec, replace the sensor if it reads out of range |
| CID 0110 - FMI 00 | Coolant temperature above normal operating range (engine monitoring high-temperature warning) | Low coolant level, plugged radiator core, slipping or failed fan drive, or a genuine overheating condition | Check coolant level and radiator condition first, confirm fan operation, then verify the sensor reading against a manual gauge before condemning parts |
| CID 0100 - FMI 04 | Engine oil pressure sensor: voltage below normal (short to ground) | Chafed harness shorting the signal wire to frame ground, corroded connector, or failed sensor | Inspect the oil pressure sensor harness for chafe/short points, check the connector, confirm actual pressure with a mechanical gauge before replacing the sensor |
| CID 0100 - FMI 01 | Engine oil pressure below normal operating range | Low oil level, worn oil pump, plugged suction screen or filter, or fuel-diluted oil | Stop and check oil level/condition immediately, do not run the engine if the warning persists, verify with a mechanical gauge before further diagnosis |
| CID 0102 - FMI 03 | Boost (intake manifold) pressure sensor: voltage above normal | Open sensor circuit, damaged connector pins, or sensor failure | Inspect the boost sensor wiring and connector for damage or corrosion, test signal per the troubleshooting guide, replace the sensor if out of calibration |
| CID 0091 - FMI 08 | Throttle position sensor: abnormal frequency, pulse width, or period | Worn or misadjusted throttle sensor, intermittent wiring connection, or sensor drifted out of calibration | Recalibrate the throttle position sensor with the diagnostic tool, inspect the harness for intermittent contact, replace the sensor if calibration fails |
| CID 0190 - FMI 08 | Engine speed/timing sensor: abnormal frequency, pulse width, or period | Sensor air gap out of spec, debris or metal on the timing wheel, or a failing speed/timing sensor | Check sensor mounting and air gap, inspect the timing wheel for damage or debris, inspect wiring before replacing the sensor |
| CID 0247 - FMI 09 | Cat Data Link: abnormal update rate (loss of communication between electronic control modules) | Damaged or corroded data link wiring, a disconnected/unpowered control module, or a software mismatch between modules | Check data link harness continuity and connectors, confirm all control modules are powered up, cycle the key and recheck with the diagnostic tool |
| MID 081 - CID 0096 - FMI 03 | Fuel level sender: voltage above normal (machine/chassis ECM) | Open return circuit at the sender, failed sender unit, or machine harness shorted to a positive voltage source | Check the fuel sender wiring and connector, verify sender resistance against spec, inspect the machine harness for chafe or damage |
| CID 0585 - FMI 08 | Transmission output speed sensor: abnormal signal | Sensor air gap or wiring fault, damaged tone wheel, or debris at the sensor tip | Check sensor air gap and connector condition, inspect the tone wheel for damage, confirm with the diagnostic tool before replacing the sensor |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
16H attachments & work tools
Moldboard / cutting edge assembly
Base moldboard is 4.88 m (16 ft) wide, 787 mm (31 in) tall, 25 mm (1 in) thick (some catalog listings for the ES variant show 4.9 m / 16.1 ft — varies by configuration/series). Hydraulic side shift runs about 650 mm (25.6 in) left and 790 mm (31.1 in) right, with tip angle to roughly 40 degrees forward and 5 degrees back. Cutting edges are curved or flat, double-bevel, serrated or plain, with specialty widths from about 250 to 400 mm (10-16 in); end bits are through-hardened wear steel bolted at the moldboard tips.
Drawbar-circle-moldboard (DCM) mounting structure
All blade-side work tools attach through the DCM group: an A-frame box-section drawbar for high strength, a circle roughly 1.82 m (71.8 in) diameter with hydraulic circle shift near 690 mm (27.2 in) left / 560 mm (22 in) right, and blade reach outside the tires of about 2.3 m (91 in) each side. This structure, not a universal quick coupler, is what sizes which moldboard, cutting-edge, and blade-mounted accessories fit the machine.
Rear ripper / scarifier
Rear-frame mounted multi-shank unit is the main heavy work tool for this size class, used to break up hard-packed haul road surface or aggregate ahead of grading. Ripper-tooth shanks handle heavy breakup; scarifier-tooth shanks are swapped in for lighter surface fracture work. It runs on a dedicated hydraulic lift group tied into the machine's main implement hydraulics, not a separate power pack.
Front scarifier
Lighter-duty scarifier hooks to the front lift group ahead of the front axle and is used for light breakup of compacted material, asphalt, or rocky subgrade before the moldboard passes. It is a distinct hydraulic lift-group attachment from the rear ripper/scarifier and is generally specified for less severe ground-breaking duty than the rear unit.
Push block / nose counterweight
Bolts to the motor grader nose plate. It counterbalances the rear ripper/scarifier attachment and doubles as a push point when the grader is used to push another machine, such as a scraper. Commonly specified together with a rear ripper on this class of machine to keep the frame balanced.
Blade lift (moldboard shock) accumulators
Factory-listed optional equipment on the 16H spec sheet. Hydraulic accumulators in the blade-lift circuit absorb vertical shock loads when the moldboard strikes an immovable object, reducing stress on the circle, drawbar, and lift cylinders.
Mounting / hydraulic-kit compatibility
Motor grader work tools do not use a generic quick-coupler; ripper, scarifier, and push-block attachments bolt or pin to model/size-matched lift-group brackets, so tools must be ordered for this machine's frame and weight class rather than shared across smaller grader lines. Hydraulic-actuated tools run off the machine's main load-sensing, axial-piston implement pump; reported flow is in the 214-254 L/min (56-66 gal/min) range and reads differently across spec sheets, so treat it as varying by configuration/series rather than a fixed figure.
Mining/guarding factory configuration
Cataloged as a standard mining motor grader, so factory options run toward jobsite protection rather than snow or urban work tools: front axle cylinder, line, and fitting guarding, and an underguard for the transmission against ground debris. Ether starting aid is standard for cold-start reliability, with air conditioning/heater arrangement and suspension seating offered as cab options for haul-road duty.
Snow-removal work tools (class-typical, verify fitment)
Cat's grader line offers front angle blades with about 30 degrees of hydraulic left/right angle and trip-edge protection, plus mast or mastless snow wings and V-plows for drift work. These are catalog items across the Cat motor grader range; because the 16H is positioned as a large mining/haul-road unit rather than a municipal snow machine, confirm with a dealer that a specific snow work tool is offered for this frame size before ordering.
All 16H assemblies by section
Every catalogued assembly group for the Caterpillar 16H. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
185-1893 Aftercooler & Mounting Gp
| 10***92 | Washer; (4.8x25x2-mm Thk) | 5 |
| 12***27 | Seal; (95-cm Each) | 0 |
| 13***85 | Rivet-Pop | 5 |
212-5958 Air Cleaner Gp
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 17***12 | Air Cleaner Group | 1 |
| 17***13 | Bracket As | 1 |
174-1612 Air Cleaner Gp
| 10***50 | Film; (Air Cleaner) (Radial Seal) (On Air Cleaner Cover) | 1 |
| 17***12 | Air Cleaner Group | 1 |
| 1N***03 | Clip Assem. | 1 |
177-2202 Elbow Gp-Air Inlet -Aftercooler
| 10***25 | Gasket; (Air Inlet Manifold)(Intake Manifold Inlet) | 1 |
| 17***02 | Elbow | 1 |
| 17***02 | Elbow Group-Air Inlet; -Aftercooler | 1 |
184-1671 Lines Gp-Aftercooler Air
| 12***29 | Clamp; (V-Band) | 1 |
| 12***00 | Adapter | 1 |
| 17***81 | Hose | 2 |
148-2142 Manifold Gp-Exhaust
| 10***13 | Gasket | 6 |
| 11***15 | Stud-Taperlock; (M10x85-mm Oal) | 12 |
| 14***42 | Manifold Group-Exhaust | 1 |
116-5405 Manifold Gp-Inlet
| 11***05 | Manifold Group-Inlet | 1 |
| 11***06 | Manifold; (Inlet) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
212-5959 Muffler & Mounting Gp
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 1 |
| 14***80 | Clamp Assem. | 1 |
| 19***92 | Clip As | 1 |
226-1187 Precleaner Gp
| 11***05 | Adapter Group-Air Cleaner | 1 |
| 13***80 | Precleaner As; (Air) | 1 |
| 17***15 | Clamp | 1 |
208-5871 Turbocharger Gp
| 1S***95 | Gasket-Turbocharger To Manifold; Gasket Turbocharger To Manifold | 1 |
| 20***71 | Turbocharger Group | 1 |
| 21***91 | Turbocharger Group | 1 |
214-6091 Turbocharger Gp
| 11***87 | Bolt; (M6x0.04x10.4-mm)(6mm X 0.04 Thd) | 1 |
| 12***53 | Clamp As; (Turbine) | 1 |
| 13***30 | Cover As-Compressor | 1 |
Basic Engine
133-7031 Air Compressor Gp
| 00***43 | Elbow; (12.7mm Id) | 1 |
| 00***58 | Elbow-Flared | 1 |
| 03***31 | Elbow-To Tube As | 1 |
234-2413 Air Compressor Gp
| 00***43 | Elbow; (12.7mm Id) | 1 |
| 00***58 | Elbow-Flared | 1 |
| 03***31 | Elbow-To Tube As | 1 |
131-6679 Air Compressor Gp
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 6 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 12 |
| 10***16 | Key-Woodruff | 1 |
167-0017 Belt Tensioner Gp
| 12***37 | Seal-O-Ring (Id=10.8mm); (Id=10.80mm) | 2 |
| 12***64 | Stud; (M12x1.75x86.3-mm Oal) | 2 |
| 12***90 | Pulley; (8-Groove)(Alternator) | 1 |
234-2412 Belt Tensioner Gp
| 12***37 | Seal-O-Ring (Id=10.8mm); (Id=10.80mm) | 1 |
| 12***64 | Stud; (M12x1.75x86.3-mm Oal) | 2 |
| 14***11 | Pulley Group-Idler | 1 |
171-3062 Camshaft Gp
| 11***59 | Cover | 1 |
| 12***11 | Journal | 1 |
| 13***68 | Gasket; (Camshaft Cover) | 1 |
174-1762 Cover Gp-Cylinder Block
| 06***55 | Seal-O-Ring (Id=47.22mm) | 3 |
| 10***69 | Seal-O-Ring; (Fuel Transfer Pump) | 1 |
| 13***16 | Cover | 1 |
132-3212 Crankshaft Gp
| 12***82 | Bearing-Main; (0.51-mm Us)(.51mm U.S.) | 0 |
| 12***83 | Bearing-Main; (0.76-mm Us)(.76mm U.S.) | 0 |
| 12***84 | Bearing-Main; (0.51-mm Os)(.51mm O.S.) | 0 |
200-2054 Cylinder Block As
| 11***66 | Cap; (Bearing) | 7 |
| 17***54 | Bolt-Hex Head; (M16x160mm) | 14 |
| 20***54 | Cylinder Block As | 1 |
204-3449 Cylinder Block As
| 10***60 | Seal; (Liner) | 6 |
| 16***63 | Shim-Liner; -Cylinder | 0 |
| 16***64 | Shim-Liner; -Cylinder | 0 |
115-2983 Cylinder Block Gp
| 11***83 | Cylinder Block Group | 1 |
| 1N***99 | Plug-O-Ring; (Straight Thread) | 2 |
| 20***49 | Cylinder Block As | 1 |
179-9462 Cylinder Head As
| 10***50 | Guide-Valve; (Standard) | 24 |
| 10***34 | Guide-Valve; (0.127-mm Os Od) | 0 |
| 10***35 | Guide-Valve; (0.508-mm Os Od) | 0 |
179-9459 Cylinder Head As
| 11***02 | Sleeve; (Injector) | 6 |
| 13***06 | Insert-Valve Seat; (Inlet)(Standard) | 12 |
| 14***52 | Insert-Valve Seat; (0.508-mm Os Od)(0.508-mm Os Od) | 12 |
116-1085 Cylinder Head Gp
| 11***85 | Cylinder Head Group | 1 |
| 14***49 | Cylinder Head Group | 1 |
| 18***07 | Gasket As-Cylinder Head | 1 |
148-2149 Cylinder Head Gp
| 10***50 | Guide-Valve; (Standard) | 24 |
| 10***34 | Guide-Valve; (0.127-mm Os Od) | 0 |
| 10***35 | Guide-Valve; (0.508-mm Os Od) | 0 |
174-1639 Drive Gp-Accessory
| 13***83 | Bolt-12 Point Head; (M10x1.5x30-mm) | 8 |
| 16***25 | Damper Assem. | 1 |
| 17***93 | Adapter | 1 |
116-1083 Fastener Gp-Cylinder Head
| 11***83 | Fastener Group-Cylinder Head; (Cylinder Head) | 1 |
| 12***84 | Bolt; (Hex Head) (M16x2x160mm) | 26 |
| 2S***58 | Washer-Hard; (17x29x3-mm Thk)(Engine Brake) | 26 |
174-1766 Flywheel Gp
| 17***66 | Flywheel Group | 1 |
| 22***41 | Flywheel As | 1 |
| 4N***14 | Gear; (113-Teeth)(Flywheel Starter) | 1 |
117-2750 Gear Gp-Front
| 11***50 | Gear Group-Front | 1 |
| 13***83 | Shaft | 1 |
| 13***86 | Gear As; (Idler) (71 Teeth) | 1 |
208-3730 Housing Gp-Flywheel
| 09***49 | Bolt; (M8x1.25x40-mm) | 2 |
| 19***51 | Cover; (1/2-20) | 1 |
| 1H***28 | Seal 6.3 cm(2.484 In.) I.D.; Seal--To Seal Pumps To Case | 1 |
133-7075 Housing Gp-Front
| 11***24 | Gear; (Pump Drive) (34 Teeth) | 1 |
| 13***75 | Housing Group-Front | 1 |
| 16***66 | Seal Group-Crankshaft; (Front) | 1 |
148-2063 Lifter Gp-Valve -Mechanism
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 2 |
| 12***93 | Dowel | 1 |
| 14***63 | Lifter Group-Valve; -Mechanism | 1 |
117-2748 Lifting Gp-Engine
| 11***05 | Plate; (Lifting Eye) | 2 |
| 11***48 | Lifting Group-Engine | 1 |
| 5P***45 | Washer-Hard; (13.5x25.5x3-mm Thk)(Turbocharger Blanking Plate) | 6 |
161-2316 Mounting Gp-Engine
| 16***16 | Mounting Group-Engine | 1 |
| 18***66 | Shim; (0.8mm Thk) | 16 |
| 18***67 | Shim; (0.4mm Thk) | 16 |
138-2550 Mounting Gp-Fan Drive
| 12***64 | Stud; (M12x1.75x86.3-mm Oal) | 2 |
| 13***50 | Mounting Group-Fan Drive; (Short) | 1 |
| 5R***37 | Washer; (Seal) (1.27mm Thk) | 2 |
116-5408 Mounting Gp-Valve Mechanism
| 11***83 | Fastener Group-Cylinder Head; (Cylinder Head) | 1 |
| 11***08 | Mounting Group-Valve Mechanism | 1 |
| 17***68 | Bridge As-Valve; (Intake) | 12 |
174-1574 Pan Gp-Oil
| 10***08 | Gasket; (Oil Pan) | 1 |
| 12***55 | Bell As-Suction | 1 |
| 17***74 | Pan Group-Oil | 1 |
252-8692 Pan Gp-Oil -Engine
| 12***55 | Bell As-Suction | 1 |
| 14***08 | Plug As. | 1 |
| 19***16 | Adapter-Drain | 1 |
130-0863 Piston & Rod Gp
| 11***99 | Plug-Pin | 2 |
| 11***16 | Rod Assem. | 1 |
| 11***72 | Bearing-Connecting Rod | 1 |
138-2028 Plug Gp-Cylinder Block
| 13***28 | Plug Group-Cylinder Block | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
265-3855 Plug Gp-Cylinder Block
| 26***55 | Plug Group-Cylinder Block | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
174-1760 Plug Gp-Engine
| 11***35 | Connector | 1 |
| 17***60 | Plug Group-Engine | 1 |
| 3B***23 | Core Plug--Flywheel Housing Pinion Shaft Hole | 1 |
142-2011 Pulley Gp-Idler
| 12***37 | Seal-O-Ring (Id=10.8mm); (Id=10.80mm) | 1 |
| 14***11 | Pulley Group-Idler | 1 |
| 14***11 | Pulley As-Idler | 1 |
115-9397 Rocker Arm Gp
| 09***14 | Pin; (Spring) | 1 |
| 11***97 | Rocker Arm Group | 1 |
| 11***98 | Arm; (Valve Rocker) (Exhaust) | 2 |
116-1091 Seal Gp-Crankshaft
| 10***80 | Seal-O-Ring (Id=177.17mm) | 1 |
| 11***91 | Seal Group-Crankshaft; -Single Lip | 1 |
| 16***23 | Cover | 1 |
174-1625 Support Gp-Engine
| 17***22 | Support | 1 |
| 17***25 | Support Group-Engine | 1 |
| 2M***49 | Washer-Retainer To Fan Bracket Assembly | 8 |
207-5900 Suppression Gp-Sound -Engine Enclosure
| 20***00 | Suppression Group-Sound; -Engine Enclosure | 1 |
| 20***01 | Panel; (Rh) | 1 |
| 20***02 | Panel; (Lh) | 1 |
117-2749 Valve Mechanism Gp -Engine
| 10***42 | Base-Valve Mechanism Cover | 1 |
| 10***67 | Pushrod; (Valve) | 12 |
| 10***68 | Pushrod-Injector | 6 |
Braking System
102-9004 Actuator Gp-Brake -Parking
| 10***04 | Actuator Group-Brake; -Parking | 1 |
| 20***14 | Air Dryer Group; -Cold Weather Operation | 1 |
| 20***25 | Hose As | 1 |
215-3005 Air Dryer Gp
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 2 |
| 10***04 | Actuator Group-Brake; -Parking | 1 |
| 11***21 | Plate As | 1 |
211-0981 Air Dryer Gp
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Actuator Group-Brake; -Parking | 1 |
208-0014 Air Dryer Gp -Cold Weather Operation
| 20***89 | Kit-Cartridge; (Desiccant)(Air Dryer) | 1 |
| 20***90 | Kit-Valve; (Cutoff)(Turbo Cutoff) | 1 |
| 20***91 | Kit-Check Valve | 1 |
8d-1690 Brake Gp-Service
| 0S***25 | Bolt, Hex. Hd., 5/8"-11 N.C. X 2 1/2" | 2 |
| 10***04 | Actuator Group-Brake; -Parking | 1 |
| 11***21 | Plate As | 1 |
188-7062 Control Gp-Parking Brake
| 11***46 | Bracket As | 1 |
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
| 15***13 | Hose As | 1 |
171-2866 Control Gp-Service Brake
| 11***91 | Adapter | 2 |
| 13***22 | Boss | 1 |
| 16***43 | Hose As | 1 |
209-9285 Lines Gp-Air Tank
| 11***37 | Valve-Quick-Release | 1 |
| 20***85 | Lines Group-Air Tank | 1 |
207-0625 Tank Gp-Air
| 16***13 | Accumulator Group-Hydraulic | 2 |
| 16***49 | Clamp | 2 |
| 18***08 | Plate As | 1 |
5d-0470 Valve Gp-Quick-Release
| 17***93 | Kit-Seal; (Hydraulic Accumulator) | 1 |
| 19***50 | Core | 1 |
| 22***67 | Valve Group-Accumulator Charging | 1 |
Cooling System
262-7138 Cooler Gp-Engine & Xmsn Oil
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 10***25 | Gasket | 1 |
| 11***17 | Core As-Engine Oil Cooler | 1 |
163-9322 Cooler Gp-Engine & Xmsn Oil
| 06***40 | Seal-O-Ring (Id=37.69mm) | 2 |
| 10***25 | Gasket | 1 |
| 11***17 | Core As-Engine Oil Cooler | 1 |
184-1670 Cooling Ar
| 17***83 | Lines Group-Hydraulic Fan; -Radiator | 1 |
| 17***61 | Fan & Motor Group | 1 |
| 18***70 | Cooling Ar | 1 |
201-1054 Cooling Ar
| 17***83 | Lines Group-Hydraulic Fan; -Radiator | 1 |
| 17***61 | Fan & Motor Group | 1 |
| 18***93 | Aftercooler & Mounting Group | 1 |
179-3261 Fan & Motor Gp
| 10***84 | Bolt-Socket Head; (M10x1.5x25-mm) | 2 |
| 15***37 | Elbow Group | 2 |
| 17***04 | Bracket As | 1 |
230-5840 Fastener Gp-Radiator
| 23***40 | Fastener Group-Radiator | 1 |
| 3E***56 | Washer-Hard; (17.5x30x6-mm Thk) | 8 |
| 8T***40 | Bolt-Plt; (M16 X 2.0 X 60) | 8 |
215-2062 Housing & Regulator Gp
| 11***00 | Housing As-Regulator | 1 |
| 12***11 | Stud; (M8x1.25-Thd)(M8x1.25 Thd Both Ends) | 2 |
| 21***62 | Housing & Regulator Group | 1 |
262-7139 Housing & Regulator Gp
| 12***11 | Stud; (M8x1.25-Thd)(M8x1.25 Thd Both Ends) | 2 |
| 24***33 | Regulator-Water Temperature; (98-Deg C)(Water, Coolant) | 1 |
| 25***62 | Manifold | 1 |
215-2063 Housing & Regulator Gp-Mtg
| 11***97 | Gasket | 4 |
| 21***63 | Housing & Regulator Group-Mtg; -Housing, Regulator | 1 |
| 26***39 | Housing & Regulator Group | 1 |
206-0400 Lines Gp-Power Train Cooler
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 14***05 | Adapter Group | 1 |
| 14***36 | Adapter; (Straight) (-6 Orb X -6 Orfs) | 1 |
118-2808 Lines Gp-Water -Water Pump Inlet Elbow
| 10***35 | Gasket | 1 |
| 10***85 | Elbow; (Water Pump) | 1 |
| 11***08 | Lines Group-Water; -Water Pump Inlet Elbow-Pump | 1 |
116-5460 Lines Gp-Water -Bypass
| 10***08 | Flange | 1 |
| 10***95 | Tube | 1 |
| 11***60 | Lines Group-Water; -Bypass | 1 |
186-4156 Lines Gp-Water
| 00***14 | Coupling-Pipe | 1 |
| 09***81 | Spacer; (10.5x20x10.0mm Thk) | 1 |
| 15***25 | Valve-Fluid Sampling | 1 |
255-5307 Lines Gp-Water -Inlet Elbow
| 10***35 | Gasket | 1 |
| 25***77 | Elbow-Water Pump | 1 |
| 25***07 | Lines Group-Water; -Inlet Elbow | 1 |
176-7000 Pump Gp-Water
| 10***10 | Gasket | 1 |
| 14***88 | Seal As; (Water Pump) | 1 |
| 17***95 | Cover-Pump | 1 |
117-2674 Pump Gp-Water
| 11***74 | Pump Group-Water | 1 |
| 17***00 | Pump Group-Water | 1 |
| 6V***21 | Bolt; (M8x1.25x80-mm) | 2 |
221-8000 Radiator & Mounting Gp
| 10***92 | Washer; (4.8x25x2-mm Thk) | 17 |
| 12***27 | Seal; (95-cm Each) | 0 |
| 13***85 | Rivet-Pop | 17 |
211-9028 Radiator Gp
| 00***14 | Coupling-Pipe | 1 |
| 1P***97 | Valve-Drain; (Radiator) | 1 |
| 21***71 | Radiator Group; -Folded Core | 1 |
211-3471 Radiator Gp -Folded Core
| 21***70 | Tank As | 1 |
| 21***71 | Radiator Group; -Folded Core | 1 |
| 21***72 | Tank As-Radiator | 1 |
Electrical And Starting System
123-6449 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***49 | Alarm Group | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
3e-6328 Alarm Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 3E***28 | Alarm Group; -Caterpillar Monitoring System-Action | 1 |
233-0712 Alternator Gp-Charging
| 12***90 | Pulley; (8-Groove)(Alternator) | 1 |
| 19***59 | Guard As | 1 |
| 20***32 | Alternator Group-Charging | 1 |
200-2232 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 18***34 | Nut-Flange; (5/8-18-Thd) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 2 |
226-7683 Alternator Gp-Charging
| 18***38 | Collar | 2 |
| 18***39 | Fan As; (Alternator) | 1 |
| 18***44 | Coil Assem. | 1 |
233-0713 Alternator Gp-Charging
| 22***83 | Alternator Group-Charging | 1 |
| 23***13 | Alternator Group-Charging | 1 |
| 23***98 | Circuit Breaker Group; -Alternator | 1 |
212-0615 Alternator Gp-Charging
| 16***57 | Bracket | 1 |
| 19***59 | Guard As | 1 |
| 20***32 | Alternator Group-Charging | 1 |
260-7647 Application Gp-Power Train
| 26***47 | Application Group-Power Train | 1 |
| 30***87 | Control Group-Unprogrammed; (Transmission) | 1 |
188-5131 Battery Gp
| 15***10 | Battery; (12-Volt, 1400-Cca) | 2 |
| 17***07 | Clip | 2 |
| 18***31 | Battery Group | 1 |
9w-0742 Block Gp-Junction -Battery
| 6V***22 | Tube-Heat Shrink; (25.4-mm Dia)(10-M) | 0 |
| 7F***60 | Washer | 6 |
| 8C***58 | Block Group-Junction; (Battery) | 1 |
272-2286 Bracket Gp-Mounting -Mast
| 24***03 | Bracket Group-Mounting | 1 |
| 25***44 | Film-Warning; (Blade, Do Not Climb, Read Omm) | 1 |
| 25***36 | Cable-Coiled; (Receiver) | 1 |
201-1036 Circuit Breaker Gp -Dual
| 19***97 | Wire As | 1 |
| 20***36 | Circuit Breaker Group; -Dual-Headlights, Lightbar | 1 |
| 20***24 | Strap | 1 |
236-5498 Circuit Breaker Gp -Alternator
| 17***12 | Circuit Breaker As; (105-Ampere) | 1 |
| 23***98 | Circuit Breaker Group; -Alternator | 1 |
| 25***11 | Lockwasher | 2 |
201-1038 Circuit Breaker Gp -Single
| 20***38 | Circuit Breaker Group; -Single | 1 |
| 20***24 | Strap | 1 |
| 3K***06 | Screw-Machine-Relay To Bracket | 2 |
168-4490 Control & Mtg Gp-Engine Elek
| 16***90 | Control & Mtg Group-Engine Elek | 1 |
| 16***94 | Spacer; (8.5x12.7x54.1-mm) | 2 |
| 21***49 | Control Group-Engine Electronic | 1 |
232-5990 Control & Mtg Gp-Engine Elek
| 20***88 | Control Group-Engine Electronic | 1 |
| 23***90 | Control & Mtg Group-Engine Elek | 1 |
| 6I***18 | Spacer; (8.2x12.7x28.7-mm Thk) | 4 |
240-5304 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 24***04 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
209-9588 Control Gp-Engine Electronic
| 20***88 | Control Group-Engine Electronic | 1 |
| 32***04 | Control Group-Engine Electronic | 1 |
348-2379 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 2L***75 | Terminal; (14-Ga To 16-Ga, No. 8 Screw)(Relay Switch "B" & "S") | 1 |
| 2L***78 | Terminal-Ring; (14-Ga To 16-Ga, 5/16-In Screw) | 1 |
210-0849 Control Gp-Engine Electronic
| 21***49 | Control Group-Engine Electronic | 1 |
| 24***04 | Control Group-Engine Electronic | 1 |
322-3604 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 32***04 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
210-0848 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 21***48 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
209-9587 Control Gp-Engine Electronic
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 20***87 | Control Group-Engine Electronic | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
132-6640 Control Gp-Secondary Steering
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***40 | Control Group-Secondary Steering | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 11 |
240-5307 Control Gp-Unprogrammed
| 18***72 | Screw-Pan Head; (No 8-32x9.52-mm)(Wax Coated) | 1 |
| 24***07 | Control Group-Unprogrammed; -Engine | 1 |
| 7X***15 | Strap; (Grounding) | 1 |
230-7490 Control Gp-Unprogrammed
| 23***90 | Control Group-Unprogrammed; -Power Train | 1 |
161-0777 Converter Ar-Electrical -High Profile
| 16***77 | Converter Ar-Electrical; -High Profile | 1 |
| 17***86 | Accessory Group-Cab; -High Profile | 1 |
| 18***43 | Converter Group-Electrical | 1 |
161-0776 Converter Ar-Electrical -Low Profile
| 16***76 | Converter Ar-Electrical; -Low Profile | 1 |
| 17***85 | Accessory Group-Cab; -Low Profile | 1 |
| 18***43 | Converter Group-Electrical | 1 |
233-6659 Converter Gp-Electrical
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***33 | Plate | 1 |
| 16***35 | Plate As | 1 |
145-1297 Converter Gp-Electrical -Radio
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 14***97 | Converter Group-Electrical; -Radio | 1 |
| 20***85 | Converter Group-Electrical; (24-Volt To 12-Volt)(Air Conditioner, Heater) | 1 |
167-8382 Converter Gp-Electrical
| 16***82 | Converter Group-Electrical; -Cab | 1 |
| 23***59 | Converter Group-Electrical | 1 |
| 9W***41 | Fuse; (15-Ampere) | 1 |
180-4643 Converter Gp-Electrical
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 18***43 | Converter Group-Electrical | 1 |
| 20***85 | Converter Group-Electrical; (24-Volt To 12-Volt)(Air Conditioner, Heater) | 1 |
253-2697 Electronics Gp-Implement
| 25***97 | Electronics Group-Implement; -Grade Control | 1 |
| 31***03 | Software Group-Implement | 1 |
| 33***83 | Service Group-Implement; (Grade Control) | 1 |
198-7332 Electronics Gp-Monitor -Cat Monitoring System
| 19***32 | Electronics Group-Monitor; -Cat Monitoring System | 1 |
| 25***01 | Electronic Control Group; (Caterpillar Monitoring System)(Electronic) | 1 |
| 30***51 | Software Group-Monitor | 1 |
247-6452 Grade Control Ar
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 13***00 | Clip; (Tab) | 4 |
| 15***24 | Knob As; (Blade Lift, Rh) | 1 |
249-7803 Grade Control Ar-Laser -Accugrade, Advanced Tracking System
| 21***82 | Kit-Laser Target; -Grade Control | 1 |
| 22***33 | Mast Group; -Laser Receiver | 1 |
| 23***49 | Cable-Coiled; (Mast) | 1 |
249-7802 Grade Control Ar-Satellite -Accugrade, Dual Gps
| 16***02 | Mounting Group-Radio | 1 |
| 24***02 | Riser; (Angle) | 2 |
| 24***91 | Receiver Group-Satellite; -Single Gps, Ms980-Accugrade | 2 |
250-3028 Grade Control Ar-Satellite -Single Gnss
| 16***02 | Mounting Group-Radio | 1 |
| 24***02 | Riser; (Angle) | 1 |
| 24***91 | Receiver Group-Satellite; -Single Gps, Ms980-Accugrade | 1 |
154-7246 Heater Gp-Jacket Water
| 12***09 | Cord As-Heater Element; -240-Volt | 1 |
| 13***17 | Cap As-Dust | 1 |
| 15***81 | Element As-Jacket Water Heater; (240-Volt, 1250-Watt) | 1 |
249-5511 Heater Gp-Jacket Water
| 12***09 | Cord As-Heater Element; -240-Volt | 1 |
| 13***17 | Cap As-Dust | 1 |
| 24***08 | Element As-Jacket Water Heater; (240-Volt, 1250-Watt) | 1 |
131-8126 Heater Gp-Jacket Water
| 13***26 | Heater Group-Jacket Water; -120 Volt | 1 |
| 13***27 | Element As-Jacket Water Heater; (120-Volt, 1250-Watt) | 1 |
| 13***17 | Cap As-Dust | 1 |
249-5516 Heater Gp-Jacket Water
| 13***17 | Cap As-Dust | 1 |
| 23***42 | Element As-Jacket Water Heater; (120-Volt, 1250-Watt) | 1 |
| 24***16 | Heater Group-Jacket Water | 1 |
239-9362 Installation Gp-Warning Beacon
| 10***62 | Switch As; (Warning Beacon) | 1 |
| 10***32 | Plate As | 1 |
| 13***00 | Clip; (Tab) | 1 |
216-0182 Kit-Laser Target -Accugrade
| 21***82 | Kit-Laser Target; -Grade Control | 1 |
| 24***22 | Target As-Laser | 1 |
| 24***98 | Case-Plastic | 1 |
3e-6389 Lamp Gp-Dome -With Switch
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 3E***89 | Lamp Group-Dome; -With Switch-Cab, Rh, Lh | 1 |
234-4323 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 23***23 | Lamp Group-Flood; -Vertical Mount | 1 |
234-4325 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***14 | Lens As; (Floodlight) | 1 |
| 23***25 | Lamp Group-Flood; -Suspended Mount | 1 |
153-2073 Lamp Gp-Flood
| 15***73 | Lamp Group-Flood; -Cab-Extended Bolster-Rear-Blade-Moldboard | 1 |
| 15***50 | Body As-Lamp | 1 |
| 15***52 | Bezel | 1 |
234-4326 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***11 | Lens As | 1 |
| 23***26 | Lamp Group-Flood; -Low | 1 |
234-4324 Lamp Gp-Flood
| 16***56 | Bracket; (Lamp Retaining) | 1 |
| 20***11 | Lens As | 1 |
| 23***24 | Lamp Group-Flood; -24-Volt, Vertical Mount | 1 |
161-3509 Lamp Gp-Head -Low Beam
| 15***50 | Body As-Lamp | 1 |
| 15***52 | Bezel | 1 |
| 16***09 | Lamp Group-Head; -Low Beam | 1 |
180-1300 Lamp Gp-Head -High Beam
| 15***49 | Lens As; (Headlight, High Beam) | 1 |
| 15***50 | Body As-Lamp | 1 |
| 15***52 | Bezel | 1 |
161-0908 Lamp Gp-Head
| 15***50 | Body As-Lamp | 1 |
| 15***52 | Bezel | 1 |
| 16***08 | Lamp Group-Head; -Fog Light | 1 |
157-0305 Lamp Gp-Head -High Beam
| 15***05 | Lamp Group-Head; -High Beam | 1 |
| 15***49 | Lens As; (Headlight, High Beam) | 1 |
| 15***50 | Body As-Lamp | 1 |
203-7626 Lamp Gp-Head & Signal -Rh
| 10***45 | Lamp; (24-Volt)(Running Lights), Cover | 2 |
| 10***49 | Lens As; (Headlight) | 1 |
| 10***50 | Lens; (Amber)(Turn Signal) | 1 |
203-7625 Lamp Gp-Head & Signal -Lh
| 10***45 | Lamp; (24-Volt)(Running Lights), Cover | 2 |
| 10***49 | Lens As; (Headlight) | 1 |
| 10***50 | Lens; (Amber)(Turn Signal) | 1 |
105-4850 Lamp Gp-Head & Signal -Rh
| 10***45 | Lamp; (24-Volt)(Running Lights), Cover | 2 |
| 10***48 | Lens As; (Headlight)(High, Low Beam) | 1 |
| 10***50 | Lens; (Amber)(Turn Signal) | 1 |
105-4849 Lamp Gp-Head & Signal -Lh
| 10***45 | Lamp; (24-Volt)(Running Lights), Cover | 2 |
| 10***48 | Lens As; (Headlight)(High, Low Beam) | 1 |
| 10***50 | Lens; (Amber)(Turn Signal) | 1 |
334-5410 Lamp Gp-Signal -Turn
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 33***10 | Lamp Group-Signal; -Turn | 1 |
199-3368 Lamp Gp-Signal
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 19***68 | Lamp Group-Signal; -Turn | 1 |
135-0426 Lamp Gp-Signal -Stop, Tail
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***26 | Lamp Group-Signal; (24-Volt, Stop, Tail)(Stop/Tail) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
135-0427 Lamp Gp-Signal -Park, Turn
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***27 | Lamp Group-Signal; -Park, Turn | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
128-6983 Lamp Gp-Warning Beacon -Rotating
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***83 | Lamp Group-Warning Beacon; -Rotating, Amber | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
235-3937 Lamp Gp-Warning Beacon -Amber, Rotating
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
| 23***37 | Lamp Group-Warning Beacon; -Amber, Rotating | 1 |
206-6538 Lighting Ar-Flood -Rear
| 20***51 | Wiring Group-Cab; -Moldboard-Snow | 1 |
| 20***35 | Lighting Group-Flood; -Moldboard-Rear | 1 |
| 20***38 | Lighting Ar-Flood; -Rear | 1 |
205-7261 Lighting Ar-Flood -Front & Rear Mounted Flood
| 16***78 | Lighting Group-Flood; -Moldboard | 1 |
| 20***61 | Lighting Ar-Flood; -Front & Rear Mounted Flood | 1 |
| 20***62 | Lighting Group-Flood; -Rear | 1 |
204-6109 Lighting Ar-Flood -Moldboard-Eu
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Suppressor As-Arc | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
161-1924 Lighting Ar-Flood & Signal -Cab-Bolster
| 16***72 | Lighting Group-Flood; -Cab, Front | 1 |
| 16***24 | Lighting Ar-Flood & Signal; -Cab-Bolster | 1 |
| 18***60 | Lighting Group-Flood; -Bolster | 1 |
186-4957 Lighting Ar-Flood & Signal -Cab-Extended Bolster
| 16***72 | Lighting Group-Flood; -Cab, Front | 1 |
| 18***70 | Lighting Group-Flood; -Extended Bolster | 1 |
| 18***57 | Lighting Ar-Flood & Signal; -Cab-Extended Bolster | 1 |
161-0770 Lighting Ar-Flood & Signal
| 16***70 | Lighting Ar-Flood & Signal; -Turn | 1 |
| 16***72 | Lighting Group-Flood; -Cab, Front | 1 |
| 16***18 | Switch Group-Light | 1 |
188-9329 Lighting Ar-Flood & Signal -Bolster
| 16***22 | Lighting Group-Flood; -Bolster-Double Worklamps | 1 |
| 18***29 | Lighting Ar-Flood & Signal; -Bolster | 1 |
| 18***31 | Lighting Group-Signal; -Rear Turn Lamps | 1 |
197-1744 Lighting Gp-Backup
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
171-7096 Lighting Gp-Backup
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
161-1922 Lighting Gp-Flood -Bolster-Double Worklamps
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***92 | Plate | 2 |
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
196-8559 Lighting Gp-Flood
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
161-1021 Lighting Gp-Flood
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 4 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 4 |
185-6660 Lighting Gp-Flood -Bolster
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***58 | Flasher As; (24-Volt) | 1 |
205-7262 Lighting Gp-Flood -Rear
| 11***10 | Grommet | 2 |
| 15***73 | Lamp Group-Flood; -Cab-Extended Bolster-Rear-Blade-Moldboard | 2 |
| 17***67 | Bracket As | 2 |
161-0772 Lighting Gp-Flood
| 11***10 | Grommet | 2 |
| 13***00 | Clip; (Tab) | 2 |
| 13***27 | Lamp Group-Signal; -Park, Turn | 2 |
161-0778 Lighting Gp-Flood
| 11***08 | Clip | 2 |
| 15***73 | Lamp Group-Flood; -Cab-Extended Bolster-Rear-Blade-Moldboard | 2 |
| 16***78 | Lighting Group-Flood; -Moldboard | 1 |
203-7620 Lighting Gp-Flood
| 20***20 | Lighting Group-Flood; -Bolster | 1 |
| 20***25 | Lamp Group-Head & Signal; -Lh Mount | 1 |
| 20***26 | . Housing, Lamp Group-Head & Signal; -Rh Mount | 1 |
183-4070 Lighting Gp-Flood -Extended Bolster
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***58 | Flasher As; (24-Volt) | 1 |
196-8532 Lighting Gp-Flood
| 03***48 | Clip; (11.11mm .437in Id) | 5 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
204-3435 Lighting Gp-Flood -Moldboard-Rear
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
192-0229 Lighting Gp-Flood -Bolster-Eu
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***49 | Lamp Group-Head & Signal; -Lh | 1 |
188-9331 Lighting Gp-Signal -Turn
| 13***27 | Lamp Group-Signal; -Park, Turn | 2 |
| 18***31 | Lighting Group-Signal; -Rear Turn Lamps | 1 |
| 5C***90 | Nut; (M6x1-Thd)(Air Inlet Heater) | 6 |
161-0774 Lighting Gp-Warning -Warning Beacon
| 16***74 | Lighting Group-Warning; -Warning Beacon | 1 |
| 23***54 | Lighting Group-Warning; -Rotating | 1 |
| 9W***42 | Fuse; (10-Ampere) | 1 |
233-4253 Lighting Gp-Warning
| 10***62 | Switch As; (Warning Beacon) | 1 |
| 10***32 | Plate As | 1 |
| 13***00 | Clip; (Tab) | 1 |
161-0773 Lighting Gp-Warning -Warning Beacon
| 16***73 | Lighting Group-Warning; -Warning Beacon | 1 |
| 23***53 | Lighting Group-Warning | 1 |
| 9W***42 | Fuse; (10-Ampere) | 1 |
239-9354 Lighting Gp-Warning -Rotating
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***62 | Switch As; (Warning Beacon) | 1 |
| 10***32 | Plate As | 1 |
292-0907 Mast Gp -Satellite Receiver
| 24***02 | Riser; (Angle) | 1 |
| 27***73 | Mast As; (Grade Control) | 1 |
| 27***86 | Bracket Group-Mounting; -Mast | 1 |
292-0281 Mast Gp -Laser Receiver
| 22***33 | Mast Group; -Laser Receiver | 1 |
| 23***70 | Mounting Group-Receiver; -Mast | 1 |
| 29***81 | Mast Group; -Laser Receiver | 1 |
226-2333 Mast Gp -Laser Receiver
| 22***33 | Mast Group; -Laser Receiver | 1 |
| 24***47 | Kit-Adapter; (Mast)(Grade Control) | 1 |
| 25***79 | Screw As | 1 |
179-8725 Motor Gp-Electric -24 Volt
| 10***41 | Starting Motor Group-Electric | 1 |
| 10***28 | Wire As | 1 |
| 17***25 | Motor Group-Electric; -24 Volt | 1 |
117-3915 Motor Gp-Electric
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 6V***01 | Nut; (3/8-16-Thd)(Plate To Rh And Lh Bracket As) | 2 |
| 7X***08 | Washer-Hard; (10.2x16x2-mm Thk) | 2 |
170-5335 Motor Gp-Electric -Circulating Fan
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***35 | Motor Group-Electric; -Circulating Fan | 1 |
| 9W***52 | Pin-Connector; (14-Ga To 16-Ga) | 2 |
254-0083 Mounting Gp-Grade Control -Blade
| 24***00 | Bracket | 1 |
| 25***31 | Bracket | 1 |
| 25***83 | Mounting Group-Grade Control; -Blade | 1 |
252-9228 Mounting Gp-Grade Control -Blade
| 24***00 | Bracket | 2 |
| 25***28 | Mounting Group-Grade Control; -Blade | 1 |
254-5961 Mounting Gp-Grade Control -Circle
| 15***39 | Nut-Weld; (M6x1-Thd)(M6x1-6h Thd) | 2 |
| 18***38 | Washer-Hard; (21x36.5x3.5-mm Thk) | 2 |
| 25***82 | Boss | 1 |
254-0084 Mounting Gp-Grade Control -Blade
| 25***31 | Bracket | 2 |
| 25***84 | Mounting Group-Grade Control; -Blade | 1 |
292-0302 Mounting Gp-Mast -Laser Receiver
| 23***52 | Film-Warning; (Laser Transmitter) | 3 |
| 25***44 | Film-Warning; (Blade, Do Not Climb, Read Omm) | 1 |
| 29***02 | Mounting Group-Mast; -Laser Receiver | 1 |
292-0908 Mounting Gp-Mast -Laser Receiver
| 23***49 | Cable-Coiled; (Mast) | 1 |
| 24***96 | Riser As; (Mast) | 1 |
| 24***03 | Bracket Group-Mounting | 1 |
234-9970 Mounting Gp-Receiver -Mast
| 23***70 | Mounting Group-Receiver; -Mast | 1 |
| 23***32 | Mount-Flexible | 4 |
| 23***33 | Gasket | 2 |
250-1934 Mounting Gp-Sensor -Sonic
| 24***04 | Mounting Group-Sensor; -Sonic | 1 |
| 25***34 | Mounting Group-Sensor; -Sonic-Accugrade | 1 |
245-7404 Mounting Gp-Sensor -Sonic
| 24***04 | Mounting Group-Sensor; -Sonic | 1 |
| 24***05 | Bracket As | 1 |
| 24***06 | Clamp | 1 |
249-7804 Receiver Ar-Laser -Dual
| 23***87 | Case-Plastic | 1 |
| 23***52 | Film-Warning; (Laser Transmitter) | 3 |
| 24***96 | Riser As; (Mast) | 2 |
292-0310 Receiver Ar-Laser -Accugrade, Dual
| 22***33 | Mast Group; -Laser Receiver | 2 |
| 23***49 | Cable-Coiled; (Mast) | 2 |
| 23***70 | Mounting Group-Receiver; -Mast | 2 |
249-7795 Receiver Ar-Laser -Single
| 23***87 | Case-Plastic | 1 |
| 23***52 | Film-Warning; (Laser Transmitter) | 3 |
| 24***96 | Riser As; (Mast) | 1 |
292-0301 Receiver Ar-Laser -Accugrade, Single
| 23***87 | Case-Plastic | 1 |
| 29***81 | Mast Group; -Laser Receiver | 1 |
| 29***85 | Receiver Group-Laser; -Accugrade, Dual | 1 |
292-0315 Receiver Ar-Satellite -Dual Gps, Ms980
| 28***37 | Receiver Group-Satellite; -Dual Gps, Ms980-Accugrade | 1 |
| 29***15 | Receiver Ar-Satellite; -Dual Gps, Ms980-Accugrade | 1 |
| 29***07 | Mast Group; -Satellite Receiver | 2 |
292-0314 Receiver Ar-Satellite -Single Gps, Ms980
| 28***36 | Receiver Group-Satellite; -Single Gps, Ms980-Accugrade | 1 |
| 29***14 | Receiver Ar-Satellite; -Single Gps, Ms980-Accugrade | 1 |
| 29***07 | Mast Group; -Satellite Receiver | 1 |
292-7972 Receiver Ar-Satellite -Accugrade, Dual Gnss, Ms992
| 24***02 | Riser; (Angle) | 1 |
| 27***73 | Mast As; (Grade Control) | 1 |
| 27***86 | Bracket Group-Mounting; -Mast | 1 |
292-7971 Receiver Ar-Satellite -Accugrade, Single Gnss, Ms992
| 24***02 | Riser; (Angle) | 1 |
| 27***73 | Mast As; (Grade Control) | 1 |
| 27***86 | Bracket Group-Mounting; -Mast | 1 |
249-7793 Receiver Gp-Laser -Single
| 22***33 | Mast Group; -Laser Receiver | 1 |
| 22***34 | Receiver Group-Laser; (Lr400c) | 1 |
| 22***67 | Adapter; (Receiver) | 1 |
292-0285 Receiver Gp-Laser -Accugrade, Dual
| 27***64 | Cable-Coiled; (Laser Receiver) | 1 |
| 29***85 | Receiver Group-Laser; -Accugrade, Dual | 1 |
| 34***59 | Receiver As-Laser | 1 |
249-7791 Receiver Gp-Satellite -Single Gps, Ms980
| 24***17 | Receiver As-Satellite; (Gps, Ms980) | 1 |
| 24***03 | Bracket Group-Mounting | 1 |
| 24***91 | Receiver Group-Satellite; -Single Gps, Ms980-Accugrade | 1 |
292-0292 Receiver Gp-Satellite -Accugrade, Single Gnss, Ms992
| 11***93 | Lockwasher | 5 |
| 25***28 | Mounting Group-Receiver; -Target | 1 |
| 25***39 | Case-Plastic; (Receiver) | 1 |
292-0291 Receiver Gp-Satellite -Accugrade, Dual Gnss, Ms992
| 11***93 | Lockwasher | 5 |
| 25***28 | Mounting Group-Receiver; -Target | 2 |
| 25***39 | Case-Plastic; (Receiver) | 1 |
286-0137 Receiver Gp-Satellite -Dual Gps, Ms980
| 11***93 | Lockwasher | 5 |
| 24***17 | Receiver As-Satellite; (Gps, Ms980) | 2 |
| 25***28 | Mounting Group-Receiver; -Target | 2 |
286-0136 Receiver Gp-Satellite -Single Gps, Ms980
| 11***93 | Lockwasher | 5 |
| 24***17 | Receiver As-Satellite; (Gps, Ms980) | 1 |
| 25***28 | Mounting Group-Receiver; -Target | 1 |
249-7789 Sensor & Mounting Gp
| 24***14 | Sensor Group-Position; (Blade Rotation) | 1 |
| 24***89 | Sensor & Mounting Group; -Cross Slope | 1 |
| 25***72 | Kit-Bracket | 1 |
185-7967 Sensor & Mtg Gp-Ground Speed
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 14***33 | Sensor Group-Ground Speed; (Radar) | 1 |
| 18***67 | Sensor & Mtg Group-Ground Speed | 1 |
262-2019 Sensor Ar-Grade -Dual Sonic
| 24***84 | Fastener Group-Sensor; -Sonic | 2 |
| 24***93 | Case-Plastic | 1 |
| 24***92 | Sensor Group-Sonic | 2 |
249-7801 Sensor Ar-Grade -Single Sonic
| 24***84 | Fastener Group-Sensor; -Sonic | 2 |
| 24***93 | Case-Plastic | 1 |
| 24***92 | Sensor Group-Sonic | 1 |
250-3027 Sensor Ar-Grade -Cross Slope B
| 22***69 | Module As-Power Supply | 1 |
| 24***89 | Sensor & Mounting Group; -Cross Slope | 1 |
| 25***33 | Wiring Group-Sensor; -Cross Slope | 1 |
262-2018 Sensor Ar-Grade -Single Sonic
| 24***84 | Fastener Group-Sensor; -Sonic | 2 |
| 24***93 | Case-Plastic | 1 |
| 24***92 | Sensor Group-Sonic | 1 |
249-7806 Sensor Ar-Grade -Dual Sonic
| 24***84 | Fastener Group-Sensor; -Sonic | 2 |
| 24***93 | Case-Plastic | 1 |
| 24***92 | Sensor Group-Sonic | 2 |
266-1467 Sensor Gp-Position -Rotary
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 12***67 | Pin-Connector; (14-Ga To 16-Ga)(14-Ga Wire) | 3 |
| 26***67 | Sensor Group-Position; -Brake Pedal | 1 |
194-6724 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 19***26 | Harness As-Sensor; (16-18 Ga Wire)(Engine Oil Temperature) | 3 |
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
197-8393 Sensor Gp-Pressure
| 16***03 | Sensor Group-Pressure; (Turbocharger Inlet, Rh) | 1 |
| 19***93 | Sensor Group-Pressure; -Atmospheric | 1 |
| 21***68 | Seal-O-Ring; (11.89-mm Id) | 1 |
197-8394 Sensor Gp-Pressure
| 16***05 | Sensor As-Pressure; (Unfiltered Engine Oil) | 1 |
| 19***94 | Sensor Group-Pressure; -Engine Oil | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
167-1709 Sensor Gp-Pressure
| 15***60 | Kit-Connecting Plug; (3-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***09 | Sensor Group-Pressure; -Injection Actuation Oil | 1 |
| 9X***13 | Sleeve (Order By cm)(Use As Required) | 0 |
197-8395 Sensor Gp-Pressure -Inlet Manifold
| 19***24 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
| 19***95 | Sensor Group-Pressure; -Air Inlet Manifold | 1 |
| 6V***48 | Seal--O-Ring--To Governor Drive Housing | 1 |
321-1456 Sensor Gp-Sonic
| 24***97 | Cable-Coiled; (Sensor) | 2 |
| 25***30 | Sensor As-Sonic; (St400) | 2 |
| 25***44 | Case-Carrying | 1 |
321-1455 Sensor Gp-Sonic
| 24***97 | Cable-Coiled; (Sensor) | 1 |
| 25***30 | Sensor As-Sonic; (St400) | 1 |
| 25***44 | Case-Carrying | 1 |
249-7792 Sensor Gp-Sonic
| 09***36 | Pin-Cotter | 1 |
| 1B***78 | Nut,Plain,Hexagon Rod To Lever Uoc:Bsv,Bsx | 2 |
| 24***15 | Sensor As-Sonic; (St300) | 1 |
272-5450 Sensor Gp-Sonic -Single Sonic
| 24***87 | Rod | 1 |
| 24***88 | Bracket Group-Mounting; -Sonic Sensor | 1 |
| 27***50 | Sensor Group-Sonic; -Single Sonic | 1 |
272-5451 Sensor Gp-Sonic -Dual
| 24***87 | Rod | 2 |
| 24***88 | Bracket Group-Mounting; -Sonic Sensor | 2 |
| 27***51 | Sensor Group-Sonic; -Dual | 1 |
197-8396 Sensor Gp-Speed -Timing, Crankshaft
| 18***11 | Sensor Group-Speed; (Crankshaft Timing) | 1 |
| 19***96 | Sensor Group-Speed; -Timing, Crankshaft | 1 |
| 20***40 | Seal-O-Ring; (13.94mm Id) | 1 |
197-8397 Sensor Gp-Speed -Timing, Camshaft
| 18***01 | Sensor Group-Speed; (Camshaft Timing) | 1 |
| 19***97 | Sensor Group-Speed; -Timing, Camshaft | 1 |
| 20***40 | Seal-O-Ring; (13.94mm Id) | 1 |
197-8392 Sensor Gp-Temperature
| 13***45 | Pad; (Connector) | 1 |
| 19***92 | Sensor Group-Temperature; -Coolant, Water | 1 |
| 26***97 | Sensor Group-Temperature; (Air Inlet Manifold) | 1 |
197-8391 Sensor Gp-Temperature
| 13***45 | Pad; (Connector) | 1 |
| 19***91 | Sensor Group-Temperature; -Air Inlet Manifold | 1 |
| 23***80 | Seal-O-Ring | 1 |
186-1728 Starting Aid Gp-Ether
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
197-0580 Starting Aid Gp-Ether -Engine
| 17***67 | Spacer; (8.8x16x10-mm Thk)(Marked X) | 2 |
| 17***91 | Tube | 1 |
| 19***80 | Starting Aid Group-Ether; -Engine | 1 |
6v-5539 Starting Motor Gp-Electric
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
| 6V***39 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 6V***82 | Starting Motor Group-Electric; (Nippondenso) | 1 |
207-1556 Starting Motor Gp-Electric
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 5 |
| 20***56 | Starting Motor Group-Electric; (24-Volt) | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
6v-5582 Starting Motor Gp-Electric
| 3E***25 | Cover As; (Starting Motor) | 1 |
| 3E***27 | Kit-Bearing; (Starting Motor)(Incl Bearing Seals & Spacers) | 1 |
| 3E***28 | Kit; (Brush) (Includes O-Rings, Screw, Spring, & Brush) | 1 |
104-7041 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 10***41 | Starting Motor Group-Electric | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
106-8554 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 0S***97 | Capscrew (1/4 - 28 Nf X 1 Gd8, Hex) | 5 |
| 10***54 | Starting Motor Group-Electric; (Delco Remy) | 1 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
161-1018 Switch Gp-Light
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***58 | Flasher As; (24-Volt) | 1 |
| 16***18 | Switch Group-Light | 1 |
118-3534 Switch Gp-Magnetic
| 11***34 | Switch Group-Magnetic; -Start Relay | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
| 17***09 | Switch Group-Magnetic; -24-Volt-Start Relay | 1 |
3e-0154 Switch Gp-Magnetic
| 3E***54 | Switch Group-Magnetic; -Secondary Steering Relay-Engine Prelubrication Relay | 1 |
| 4D***26 | Washer,Lock Starter Ground Cable, Internal And External Teeth | 2 |
| 6V***78 | Nut; (10-32-Thd) | 2 |
175-2309 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***81 | Switch As-Magnetic; (Start Relay) | 1 |
167-0138 Switch Gp-Magnetic
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***38 | Switch Group-Magnetic; -Main Relay-Main Power Relay | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
241-8368 Switch Gp-Magnetic
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
| 24***68 | Switch Group-Magnetic; -Main Power Relay-Main Relay | 1 |
254-3783 Switch Gp-Magnetic
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 18***36 | Socket-Connector; (16-Ga To 18-Ga) | 2 |
| 25***83 | Switch Group-Magnetic; -Main Relay-Main Power Relay | 1 |
175-2308 Switch Gp-Magnetic
| 01***80 | Lockwasher | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***08 | Switch Group-Magnetic; -24-Volt-Start Relay-Main Relay | 1 |
275-7741 Switch Gp-Wiper -Intermittent
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 27***41 | Switch Group-Wiper; -Intermittent-Front, Rear | 1 |
3e-0155 Switch Gp-Wiper -Intermittent
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***86 | Wiper Switch Assembly; (24-Volt)(Front/Intermittent) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
161-1930 Wiring Gp-Blade Cushion
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 4 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
247-6437 Wiring Gp-Cab
| 11***27 | Screw-Machine; (M6x1x30-mm) | 2 |
| 13***00 | Clip; (Tab) | 4 |
| 15***75 | Ladder Clip | 2 |
203-6551 Wiring Gp-Cab -Moldboard
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
161-1921 Wiring Gp-Cab -Warning Beacon
| 16***21 | Wiring Group-Cab; -Warning Beacon | 1 |
| 23***62 | Installation Group-Warning Beacon | 1 |
| 9W***42 | Fuse; (10-Ampere) | 1 |
204-6127 Wiring Gp-Cab -Moldboard
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
159-5878 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 3 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 9 |
159-5843 Wiring Gp-Console
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
171-1103 Wiring Gp-Engine
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***89 | Clip; (Ladder) | 1 |
159-5867 Wiring Gp-Front
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 4 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 8 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 3 |
233-4648 Wiring Gp-Grade Control
| 03***48 | Clip; (11.11mm .437in Id) | 2 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
252-5709 Wiring Gp-Grade Control -Cab, Indicator Lamp
| 11***48 | Lamp; (24-Volt, 3-Watt)(Clear)(Fuel Level Gauge) | 1 |
| 24***57 | Wiring As; (Accugrade) | 1 |
| 25***09 | Wiring Group-Grade Control; -Cab, Indicator Lamp | 1 |
247-6436 Wiring Gp-Grade Control
| 12***90 | Plate-Information; (Engine) | 1 |
| 13***89 | Clip; (Ladder) | 2 |
| 24***73 | Wire As | 1 |
250-1930 Wiring Gp-Monitor
| 15***02 | Knob | 1 |
| 24***04 | Mounting Group-Monitor; -Cb420 Display | 1 |
| 24***09 | Bracket As | 1 |
251-9569 Wiring Gp-Monitor
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***00 | Clip; (Tab) | 1 |
| 15***55 | Kit; (Connecting Plug) (12-Pin) (Includes Plug As Wedge & Interface Seal) | 1 |
250-1919 Wiring Gp-Monitor
| 24***04 | Mounting Group-Monitor; -Cb420 Display | 1 |
| 25***19 | Wiring Group-Monitor | 1 |
| 25***69 | Wiring Group-Monitor | 1 |
249-8901 Wiring Gp-Radio
| 03***48 | Clip; (11.11mm .437in Id) | 8 |
| 19***14 | Kit-Receptacle; (12-Pin) | 0 |
| 24***47 | Harness As-Radio | 1 |
254-1561 Wiring Gp-Radio
| 24***01 | Wiring Group-Radio | 1 |
| 25***61 | Wiring Group-Radio | 1 |
200-4983 Wiring Gp-Rear -Eu
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 2 |
| 11***55 | Rod | 2 |
230-1384 Wiring Gp-Rear
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
205-3110 Wiring Gp-Rear -Service Center-Rh
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
161-1929 Wiring Gp-Rear
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 3 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
194-7982 Wiring Gp-Rear Lighting -Radiator
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 5 |
| 11***10 | Grommet | 2 |
318-1141 Wiring Gp-Rear Lighting
| 29***49 | Plate | 1 |
| 30***46 | Harness As-Rear; (Brake Pressure) | 1 |
| 31***41 | Wiring Group-Rear Lighting | 1 |
184-6045 Wiring Gp-Secondary Steering
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 13***00 | Clip; (Tab) | 2 |
| 13***40 | Control Group-Secondary Steering | 1 |
250-1933 Wiring Gp-Sensor -Cross Slope
| 25***33 | Wiring Group-Sensor; -Cross Slope | 1 |
| 25***40 | Wiring Group-Sensor; -Cross Slope | 1 |
251-2140 Wiring Gp-Sensor -Cross Slope
| 06***65 | Bolt; (1/2-13x1.25-In) | 2 |
| 08***60 | Washer; (5.3x25x1.6-mm Thk) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
159-5855 Wiring Gp-Steering Console
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 2 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***83 | Plate | 1 |
117-2760 Wiring Gp-Unit Injector
| 10***33 | Kit; (Receptacle) (Includes Receptacle As) | 0 |
| 11***60 | Wiring Group-Unit Injector | 1 |
| 2V***16 | Clip; (9.52mm Id) | 4 |
Engine Arrangement
204-7983 Engine Ar
| 11***83 | Cylinder Block Group | 1 |
| 11***85 | Cylinder Head Group | 1 |
| 11***91 | Seal Group-Crankshaft; -Single Lip | 1 |
Frame And Body
339-9374 Axle Gp-Front
| 09***36 | Pin-Cotter | 1 |
| 1B***78 | Nut,Plain,Hexagon Rod To Lever Uoc:Bsv,Bsx | 2 |
| 28***87 | Handle As | 1 |
110-7720 Axle Gp-Front
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
| 0V***75 | Screw,Cap,Hexagon H Shaft Mtg,Accessory Drive | 6 |
| 11***20 | Axle Group-Front | 1 |
248-1488 Bracket Gp-Mounting -Sonic Sensor
| 11***93 | Lockwasher | 5 |
| 11***73 | Screw-Button Head; (10-32x0.75-In) | 2 |
| 24***88 | Bracket Group-Mounting; -Sonic Sensor | 1 |
252-5237 Bracket Gp-Mounting -Laser Target
| 00***62 | Seal-O-Ring; (63.17mm Id) | 1 |
| 18***82 | Case & Frame As | 1 |
| 19***98 | Valve-Drain; (Fuel Sump) | 1 |
161-1130 Case & Frame Gp
| 12***49 | Bracket As | 4 |
| 16***30 | Case & Frame Group | 1 |
| 22***12 | Bracket | 2 |
261-4183 Cover Gp-Protection
| 12***68 | Lock As | 1 |
| 12***38 | Screw-Machine; (M6x1x16-mm) | 16 |
| 12***78 | Locknut; (M6x1-Thd) | 16 |
206-3900 Enclosure Gp-Engine
| 20***00 | Enclosure Group-Engine | 1 |
| 3E***56 | Washer-Hard; (17.5x30x6-mm Thk) | 4 |
| 8T***40 | Bolt-Plt; (M16 X 2.0 X 60) | 4 |
230-7570 Fastener Gp-Grease Lines -Central Lubrication Mounting
| 23***70 | Fastener Group-Grease Lines; -Central Lubrication Mounting | 1 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 2 |
| 5S***85 | Lockwasher | 2 |
321-1457 Fastener Gp-Sensor -Sonic
| 11***00 | Cover; (Rh) | 1 |
| 11***01 | Cover; (Lh) | 1 |
| 11***47 | Cover | 1 |
248-1484 Fastener Gp-Sensor
| 24***05 | Bracket As | 2 |
| 24***06 | Clamp | 2 |
| 24***07 | Bracket As | 2 |
161-1181 Frame Gp-Front
| 12***59 | Step As | 1 |
| 13***71 | Clip | 8 |
| 16***81 | Frame Group-Front | 1 |
221-2349 Guard & Support Gp-Radiator
| 0L***78 | Bolt,Machine Governor And Decelerator Control | 4 |
| 22***49 | Guard & Support Group-Radiator | 1 |
| 5P***52 | Washer 6.35 mm(.25 In.) Thick | 4 |
8x-4146 Guard Gp-Bottom
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 8 |
| 5P***28 | Capscrew; (Hex Hd) (1/2-13 Unc X 1.00, Gd 8 Z) | 4 |
| 6G***19 | Shield As; (Rh) | 1 |
166-7065 Guard Gp-Platform -Non-Rops
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 8 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 4 |
166-7064 Guard Gp-Platform -Open
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***72 | Clip As-Connector; (8-Pin) | 1 |
106-4886 Hitch Gp-Articulating
| 10***86 | Hitch Group-Articulating | 1 |
| 1A***63 | Bolt, Hex, Hd., 3/4"-10 N.C. X 2 1/2" | 2 |
| 20***26 | Hitch As | 1 |
194-2838 Hitch Gp-Towing
| 14***36 | Tie Rod Group; (Steering) | 1 |
| 14***37 | Tie Rod Group; (Steering) | 1 |
| 14***41 | Clamp | 2 |
128-2522 Lines Gp-Lubrication
| 12***22 | Lines Group-Lubrication | 1 |
| 18***28 | Starting Aid Group-Ether | 1 |
| 18***31 | Battery Group | 1 |
141-6145 Link Gp-Steering
| 12***98 | Plate; (Rh) | 2 |
| 12***99 | Plate; (Lh) | 2 |
| 14***43 | Support-Step; (Rubber)(Step Access) | 4 |
288-6307 Mounting Gp-Axle -Front
| 1D***66 | Bolt, Rd. Hd. Sq Neck, 1/2" N.C. X 2" | 26 |
| 25***22 | Plate | 6 |
| 25***23 | Plate | 6 |
204-7938 Service Center Ar
| 19***47 | Bracket | 2 |
| 19***79 | Bracket; (Rh) | 1 |
| 19***95 | Bracket As; (Lh) | 1 |
6g-6900 Guard Gp-Drive Shaft
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***72 | Clip As-Connector; (8-Pin) | 1 |
255-2314 Step Gp
| 20***02 | Platform As | 1 |
| 25***14 | Step Group | 1 |
| 8T***40 | Bolt-Plt; (M16 X 2.0 X 60) | 4 |
8x-1035 Step Gp -Belted
| 19***47 | Bracket | 2 |
| 19***95 | Bracket As; (Lh) | 1 |
| 19***68 | Bracket As | 2 |
206-0335 Support Gp-Fuel Tank
| 0A***21 | Clip | 1 |
| 17***79 | Hose As | 1 |
| 19***45 | Reservoir | 1 |
206-6580 Support Gp-Platform
| 20***80 | Support Group-Platform | 1 |
| 20***14 | Air Dryer Group; -Cold Weather Operation | 1 |
| 20***25 | Hose As | 1 |
Fuel System
204-9756 Adapter Gp-Fast Fill Fuel
| 0S***21 | Bolt --Brace To Starting Engine Mounting Pad; Bolt-- Brace To Starting Engine Mounting Pad | 2 |
| 12***63 | Adapter Group-Fast Fill Fuel; (Auto Shutoff) | 1 |
| 12***71 | Clamp-Hose | 1 |
164-4858 Cap Gp-Fuel Filler -Extreme Service, Lockable
| 16***58 | Cap Group-Fuel Filler; -Extreme Service, Lockable | 1 |
| 19***75 | Cover As-Filter; (Fuel Cap) | 1 |
| 9X***00 | Seal-O-Ring | 1 |
288-2738 Cap Gp-Fuel Filler -Extreme Service, Lockable
| 16***58 | Cap Group-Fuel Filler; -Extreme Service, Lockable | 1 |
| 19***75 | Cover As-Filter; (Fuel Cap) | 1 |
| 28***38 | Cap Group-Fuel Filler; -Extreme Service, Lockable, Engine Brake Slave Piston | 1 |
159-5935 Control Gp-Governor
| 00***08 | Setscrew-Socket; (3/8-16x0.5-In) | 1 |
| 11***10 | Grommet | 1 |
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
230-4617 Fastener Gp-Fuel Tank
| 17***92 | Spacer; (13.87x21.33x28-mm Thk) | 4 |
| 23***17 | Fastener Group-Fuel Tank | 1 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 14 |
116-5436 Filter Gp-Fuel
| 11***36 | Filter Group-Fuel; -Secondary | 1 |
| 1R***62 | Filter As-Fuel; (Advanced Efficiency)(Secondary) | 1 |
133-5671 Filter Gp-Water Sep & Fuel
| 12***75 | Bowl As-Water Collection; (Water Separator, Fuel Filter) | 1 |
| 13***71 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 13***73 | Element; (Filter) (Fuel/Water Separator) (Primary) | 1 |
203-7685 Injector Gp-Fuel
| 11***84 | Seal-O-Ring; (32.99mm Id) | 1 |
| 20***85 | Injector Group-Fuel | 1 |
| 21***98 | Seal-O-Ring; (34.56mm Id) | 1 |
350-7555 Injector Gp-Fuel
| 11***84 | Seal-O-Ring; (32.99mm Id) | 1 |
| 21***98 | Seal-O-Ring; (34.56mm Id) | 1 |
| 35***55 | Injector Group-Fuel | 1 |
233-6663 Lines Gp-Fuel
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 1 |
| 12***79 | Manifold; (Fuel) | 1 |
| 14***07 | Plug; (Hex Head) (-6 Orb) (Current) (16***35 Friction Disc Interchangeable With 11***47) (Use All Of One Part Number) | 1 |
222-6417 Lines Gp-Fuel -Crossover
| 16***23 | Grommet | 2 |
| 19***37 | Fitting; (Quick) | 1 |
| 19***38 | Coupler; (Quick) | 1 |
184-1479 Lines Gp-Fuel
| 13***71 | Filter Group-Water Sep & Fuel; -Primary | 1 |
| 14***18 | Connector As | 1 |
| 14***38 | Adapter, -6 Orb / Orfs X-Long | 1 |
204-0638 Lines Gp-Fuel Injection
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 1 |
| 11***16 | Hose Assem. | 1 |
| 11***18 | Hose As | 1 |
222-9203 Manifold Gp-Fuel
| 16***55 | Valve As-Shutoff; (Fast Fill Fuel) | 1 |
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 21***71 | Manifold As | 1 |
116-5428 Pump & Mtg Gp-Fuel Transfer
| 09***70 | Washer-Sealing | 2 |
| 11***28 | Pump & Mtg Group-Fuel Transfer; (Fuel Transfer) | 1 |
| 19***82 | Tube As | 1 |
189-0351 Pump Gp-Fuel Injection
| 15***01 | Bolt; (8x1.25x7-mm)(M8x1.25x70mm) | 1 |
| 18***51 | Pump Group-Fuel Injection | 1 |
| 35***55 | Injector Group-Fuel | 1 |
116-5438 Pump Gp-Fuel Priming
| 10***08 | Pump As; (Fuel Priming) | 1 |
| 11***38 | Pump Group-Fuel Priming; (Fuel Priming) | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 1 |
263-8506 Pump Gp-Fuel Priming
| 06***39 | Seal-O-Ring | 1 |
| 13***41 | Pump Group-Fuel Priming; (Hand) | 1 |
| 1B***82 | Bolt (1.25 In. Long X .313 In. Dia.) | 1 |
219-1128 Tank Gp-Fuel -Lh
| 00***54 | Nipple-Pipe | 1 |
| 11***45 | Clamp-Hose | 1 |
| 17***18 | Sender As-Fuel Level | 1 |
208-0802 Tank Gp-Fuel -Rh
| 00***54 | Nipple-Pipe | 1 |
| 11***45 | Clamp-Hose | 1 |
| 19***12 | Coupler | 1 |
161-1126 Tank Gp-Fuel
| 11***57 | Rod | 2 |
| 16***26 | Tank Group-Fuel | 1 |
| 17***92 | Spacer; (13.87x21.33x28-mm Thk) | 4 |
208-0801 Tank Gp-Fuel -Lh
| 00***54 | Nipple-Pipe | 1 |
| 11***45 | Clamp-Hose | 1 |
| 17***18 | Sender As-Fuel Level | 1 |
219-0702 Tank Gp-Fuel
| 11***57 | Rod | 2 |
| 17***92 | Spacer; (13.87x21.33x28-mm Thk) | 4 |
| 19***07 | Strainer-Fuel | 1 |
2g-9000 Valve As-Tank -Fast Fill Fuel
| 2G***00 | Valve As-Tank | 1 |
281-2725 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 28***25 | Valve Group-Check; -Fuel | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
238-0296 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 23***96 | Valve Group-Check; -Fuel Filter | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
233-6742 Valve Gp-Check -Fuel
| 23***42 | Valve Group-Check; -Fuel Filter | 1 |
| 23***96 | Valve Group-Check; -Fuel Filter | 1 |
| 6V***89 | Seal-O-Ring (Id=19.18mm) | 1 |
156-5783 Valve Gp-Check -Fuel
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 15***83 | Valve Group-Check; -Fuel | 1 |
| 6V***23 | Ring; (Backup) (13.16mm Id) | 1 |
Hydraulic System
166-3367 Accumulator & Mtg Gp-Hydraulic
| 11***10 | Protector-Gas Valve | 1 |
| 13***23 | Piston | 1 |
| 16***67 | Accumulator & Mtg Group-Hydraulic | 1 |
219-8035 Accumulator Gp-Blade Cushion -Charged
| 16***49 | Clamp | 2 |
| 18***08 | Plate As | 1 |
| 21***35 | Accumulator Group-Blade Cushion; -Charged | 3 |
219-8064 Accumulator Gp-Blade Cushion -Uncharged
| 1J***71 | Seal (10.52 Degrees I.D.); Seal-O-Ring -- To Adapter | 1 |
| 21***64 | Accumulator Group-Blade Cushion; -Uncharged | 1 |
| 22***32 | Cap; (Gas Valve) | 1 |
160-9413 Accumulator Gp-Hydraulic
| 16***13 | Accumulator Group-Hydraulic | 1 |
221-2800 Accumulator Gp-Hydraulic -Eu
| 16***06 | Lines Group-Ripper | 1 |
| 22***00 | Accumulator Group-Hydraulic; -Eu | 1 |
| 7I***72 | Valve & Linkage Group; -Bank 4-Rh-Bank 5-Lh | 1 |
248-6252 Accumulator Gp-Steering -Uncharged
| 12***97 | Valve & Linkage Group; -5-Bank, Rh, Lh | 1 |
| 16***08 | Lines Group-Ripper; -Hydraulic Control | 1 |
| 24***52 | Accumulator Group-Steering; -Uncharged | 1 |
248-6251 Accumulator Gp-Steering -Charged
| 12***99 | Valve & Linkage Group; -6-Bank, Rh; 7-Bank, Lh | 1 |
| 16***08 | Lines Group-Ripper; -Hydraulic Control | 1 |
| 24***51 | Accumulator Group-Steering; -Charged | 1 |
254-0220 Control Ar-Hydraulic -Plow,Dozer,Ripper
| 16***06 | Lines Group-Ripper | 1 |
| 25***20 | Control Ar-Hydraulic; -Plow,Dozer,Ripper | 1 |
| 25***48 | Valve & Linkage Group | 1 |
184-7308 Control Ar-Hydraulic
| 16***06 | Lines Group-Ripper | 1 |
| 18***08 | Control Ar-Hydraulic; -Eu | 1 |
| 25***43 | Valve & Linkage Group | 1 |
254-0223 Control Ar-Hydraulic
| 1B***64 | Bolt (2.125"Long) | 2 |
| 1D***10 | Bolt 82.55 mm (3.25 In.) Long) | 2 |
| 1K***81 | Washer | 14 |
265-7821 Control Ar-Hydraulic
| 1D***15 | Bolt 139.70 mm(5.50 In.) Long | 8 |
| 1D***30 | Bolt 101.6 mm(4 In.) Long | 4 |
| 26***21 | Control Ar-Hydraulic | 1 |
194-7985 Control Ar-Hydraulic -Eu
| 16***06 | Lines Group-Ripper | 1 |
| 19***85 | Control Ar-Hydraulic; -Eu | 1 |
| 25***45 | Valve & Linkage Group | 1 |
166-3405 Control Ar-Hydraulic
| 12***90 | Valve & Linkage Group; -4-Bank, Rh; 5-Bank, Lh | 1 |
| 16***08 | Lines Group-Ripper; -Hydraulic Control | 1 |
| 16***05 | Control Ar-Hydraulic | 1 |
184-7307 Control Ar-Hydraulic
| 12***20 | Valve & Linkage Group; -Bank 4-Rh-Bank 5-Lh | 1 |
| 16***06 | Lines Group-Ripper | 1 |
| 18***07 | Control Ar-Hydraulic | 1 |
254-0221 Control Ar-Hydraulic
| 16***06 | Lines Group-Ripper | 1 |
| 25***21 | Control Ar-Hydraulic | 1 |
| 26***24 | Valve & Linkage Group | 1 |
254-0219 Control Ar-Hydraulic
| 16***06 | Lines Group-Ripper | 1 |
| 25***19 | Control Ar-Hydraulic | 1 |
| 25***47 | Valve & Linkage Group | 1 |
254-0218 Control Ar-Hydraulic
| 16***06 | Lines Group-Ripper | 1 |
| 25***18 | Control Ar-Hydraulic | 1 |
| 25***46 | Valve & Linkage Group | 1 |
194-4020 Control Ar-Hydraulic
| 16***06 | Lines Group-Ripper | 1 |
| 19***20 | Control Ar-Hydraulic | 1 |
| 25***44 | Valve & Linkage Group | 1 |
254-0222 Control Ar-Hydraulic
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***57 | Plate | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
184-7305 Control Ar-Hydraulic -Eu
| 12***35 | Valve & Linkage Group; -4-Bank, Rh; 7-Bank, Lh | 1 |
| 16***08 | Lines Group-Ripper; -Hydraulic Control | 1 |
| 18***05 | Control Ar-Hydraulic; -Eu | 1 |
173-7375 Control Gp-Centershift Lock
| 17***75 | Control Group-Centershift Lock | 1 |
| 5P***28 | Capscrew; (Hex Hd) (1/2-13 Unc X 1.00, Gd 8 Z) | 2 |
| 8T***23 | Washer-Hard; (13.5x25.5x3-mm Thk)(Bolt To Shield) | 2 |
8w-3258 Cylinder & Mtg Gp-Articulation
| 24***37 | Spacer; (39x75x20-mm Thk) | 2 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 2 |
| 8T***92 | Capscrew; (Hex Hd) (M12 X 1.75 X 25, Gr10.9, Z) | 2 |
8w-3261 Cylinder & Mtg Gp-Blade Lift
| 1D***30 | Bolt 101.6 mm(4 In.) Long | 4 |
| 2G***01 | Cap | 2 |
| 2G***06 | Shim; (0.5-mm Thk) | 8 |
260-3646 Cylinder & Mtg Gp-Blade Tip
| 14***36 | Tie Rod Group; (Steering) | 2 |
| 16***06 | Cylinder Group-Steering; -Rh | 1 |
| 16***07 | Cylinder Group-Steering | 1 |
8w-3255 Cylinder & Mtg Gp-Blade Tip
| 1D***26 | Bolt 6.99 cm(2.75 In.) Long | 4 |
| 1H***78 | Pin | 1 |
| 1K***72 | Locknut Horn To Guard | 1 |
8w-3262 Cylinder & Mtg Gp-Centershift
| 0S***92 | Bolt--Cover To Flywheel Housing | 1 |
| 12***44 | Cylinder Group-Wheel Lean | 1 |
| 2G***67 | Retainer | 1 |
8w-3257 Cylinder & Mtg Gp-Sideshift
| 16***01 | Seal As-Buffer | 1 |
| 16***12 | Seal-U-Cup | 1 |
| 17***81 | Head | 1 |
8w-3260 Cylinder & Mtg Gp-Steering
| 17***83 | Bolt-Hex Head; (M30x3.5x90mm) | 1 |
| 17***00 | Seal-O-Ring | 1 |
| 22***82 | Seal-Wiper | 0 |
8w-3259 Cylinder & Mtg Gp-Wheel Lean
| 12***97 | Head | 1 |
| 16***01 | Seal As-Buffer | 1 |
| 16***12 | Seal-U-Cup | 1 |
9t-3050 Cylinder Gp-Articulation
| 12***97 | Head | 1 |
| 16***01 | Seal As-Buffer | 1 |
| 16***12 | Seal-U-Cup | 1 |
9t-8944 Cylinder Gp-Blade Tip
| 11***76 | Cylinder As | 1 |
| 11***81 | Rod As | 1 |
| 12***95 | Head | 1 |
9t-3312 Cylinder Gp-Centershift
| 16***01 | Seal As-Buffer | 1 |
| 16***12 | Seal-U-Cup | 1 |
| 17***81 | Head | 1 |
9t-3106 Cylinder Gp-Lift
| 15***49 | Head | 1 |
| 16***91 | Seal As-Buffer | 1 |
| 16***00 | Seal-U-Cup | 1 |
113-5264 Cylinder Gp-Ripper
| 11***64 | Cylinder Group-Ripper | 1 |
| 15***49 | Head | 1 |
| 16***91 | Seal As-Buffer | 1 |
9t-3206 Cylinder Gp-Sideshift
| 12***47 | Rod As | 1 |
| 12***77 | Cylinder As | 1 |
| 16***00 | Seal Assem. | 1 |
165-2507 Cylinder Gp-Steering
| 10***74 | Retainer | 1 |
| 12***87 | Piston | 1 |
| 12***88 | Retainer | 1 |
165-2506 Cylinder Gp-Steering -Rh
| 10***74 | Retainer | 1 |
| 10***75 | Retainer | 1 |
| 10***23 | Spring | 1 |
121-9244 Cylinder Gp-Wheel Lean
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 11 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 12***44 | Cylinder Group-Wheel Lean | 1 |
108-4916 Detent Gp-Control Valve
| 10***10 | Clamp | 7 |
| 10***16 | Detent Group-Control Valve; -Plow, Bulldozer Lift | 1 |
| 11***40 | Valve & Mounting Group; -Blade Cushion | 1 |
130-3535 Detent Gp-Control Valve
| 10***10 | Clamp | 7 |
| 11***40 | Valve & Mounting Group; -Blade Cushion | 1 |
| 11***87 | Hose As; (Lift Cylinder) | 1 |
5t-1740 Drive Gp-Circle
| 10***05 | Hose As | 1 |
| 10***09 | Hose As | 1 |
| 10***10 | Clamp | 5 |
188-7194 Lines Gp-Hydraulic -Lh
| 13***79 | Hose As | 1 |
| 14***13 | Adapter Group | 1 |
| 14***25 | Connector As. | 1 |
188-7195 Lines Gp-Hydraulic -Rh
| 18***95 | Lines Group-Hydraulic; -Rh | 1 |
| 20***04 | Hose As | 1 |
| 24***77 | Hose As | 1 |
188-7254 Lines Gp-Hydraulic Fan
| 08***91 | Bolt; (M10x1.5x55-mm) | 4 |
| 10***15 | Elbow Group | 1 |
| 11***34 | Hose Assem. | 1 |
175-6983 Lines Gp-Hydraulic Fan -Radiator
| 08***91 | Bolt; (M10x1.5x55-mm) | 4 |
| 10***15 | Elbow Group | 1 |
| 11***34 | Hose Assem. | 1 |
243-0420 Lines Gp-Hydraulic Fan
| 08***91 | Bolt; (M10x1.5x55-mm) | 4 |
| 10***15 | Elbow Group | 1 |
| 11***34 | Hose Assem. | 1 |
188-0756 Lines Gp-Pump
| 08***91 | Bolt; (M10x1.5x55-mm) | 4 |
| 10***15 | Elbow Group | 1 |
| 10***05 | Tee-O-Ring | 1 |
243-0427 Lines Gp-Pump
| 14***46 | Elbow, 90, -8 Orb / Orfs | 1 |
| 14***64 | Elbow, 90°,-8 Orb /-8 Orfs | 1 |
| 18***44 | Union | 1 |
166-3308 Lines Gp-Ripper
| 10***12 | Hose As | 1 |
| 10***13 | Hose As | 1 |
| 11***89 | Hose As | 1 |
166-3406 Lines Gp-Ripper
| 10***02 | Hose As | 2 |
| 12***06 | Tee-O-Ring | 1 |
| 13***30 | Seal; (12.7mm Id) | 1 |
207-3736 Lines Gp-Ripper
| 10***02 | Hose As | 2 |
| 12***06 | Tee-O-Ring | 1 |
| 13***30 | Seal; (12.7mm Id) | 1 |
166-3333 Lines Gp-Secondary Steering
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0T***29 | Locking Plate,Nut A Pump Mtg Part Of Kit P/N 5r***25 | 1 |
| 16***33 | Lines Group-Secondary Steering; -Outside Nacd | 1 |
188-7196 Lines Gp-Steering
| 18***95 | Valve Group-Solenoid; -Demand Fan | 1 |
| 18***96 | Lines Group-Steering | 1 |
| 3E***84 | Manifold | 1 |
9d-5715 Lock Gp-Centershift
| 24***89 | Valve Group-Shuttle | 1 |
| 24***51 | Valve Group-Control | 1 |
| 26***99 | Valve Group-Solenoid & Manifold | 1 |
193-5765 Manifold Gp-Control -Hydraulic Fan
| 09***95 | Pin, Dowel | 4 |
| 17***55 | Seal-Shaft | 1 |
| 19***65 | Manifold Group-Control; -Hydraulic Fan | 1 |
239-9893 Manifold Gp-Valve -Lh
| 23***93 | Manifold Group-Valve; -Lh | 1 |
| 6Y***32 | Bearing-Thrust | 1 |
| 6Y***33 | Ring-Thrust | 2 |
239-9894 Manifold Gp-Valve -Rh
| 11***15 | Motor Group-Electric; -Engine Prelubrication-Sec Steering, Brake Release | 1 |
| 12***14 | Pump; (Secondary Steering) | 1 |
| 1A***09 | Capscrew (3/8 - 24 Nf X 1 1/4 Gd8, Hex) | 2 |
224-7040 Motor Gp-Gear
| 17***17 | Pump Group-Piston; -Hydraulic Steering | 1 |
| 18***48 | Pump Group-Piston; -Hydraulic Fan | 1 |
| 18***18 | Plate As | 1 |
9t-5977 Motor Gp-Gerotor
| 10***04 | Coupling-Shaft | 1 |
| 18***18 | Plate As | 1 |
| 23***57 | Pump Group-Piston | 1 |
123-8915 Pump & Motor Gp -Secondary Steering
| 10***04 | Coupling-Shaft | 1 |
| 12***15 | Pump & Motor Group; -Engine Prelubrication | 1 |
| 17***17 | Pump Group-Piston; -Hydraulic Steering | 1 |
237-7627 Pump & Mtg Gp-Piston
| 00***69 | Cup-Roller Bearing | 1 |
| 00***71 | Cone-Bearing | 1 |
| 03***36 | Seal-O-Ring | 1 |
180-5446 Pump & Mtg Gp-Piston
| 12***15 | Pump & Motor Group; -Engine Prelubrication | 1 |
| 18***46 | Pump & Mtg Group-Piston | 1 |
7i-4756 Pump & Mtg Gp-Secondary Steer
| 09***47 | Pin, Dowel | 1 |
| 13***78 | Seal; (112.9mm Od) | 1 |
| 13***23 | Plug-Break Off | 1 |
111-0491 Pump Gp-Metering
| 11***91 | Pump Group-Metering | 1 |
| 11***16 | Seal-O-Ring | 4 |
| 12***94 | Plug; (Break Off) | 1 |
177-7517 Pump Gp-Piston -Hydraulic Steering
| 00***69 | Cup-Roller Bearing | 1 |
| 00***71 | Cone-Bearing | 1 |
| 03***36 | Seal-O-Ring | 1 |
235-4257 Pump Gp-Piston
| 18***24 | Kit-Piston | 1 |
| 18***25 | Barrel | 1 |
| 18***26 | Plate | 1 |
184-7448 Pump Gp-Piston -Hydraulic Fan
| 18***48 | Pump Group-Piston; -Hydraulic Fan | 1 |
| 6E***17 | Plate-Limiter | 2 |
| 6E***18 | Plate-Spacer | 2 |
241-0165 Pump Gp-Piston
| 15***12 | Piston Assem. | 9 |
| 15***15 | Plate | 1 |
| 15***16 | Guide; (Ball) | 1 |
194-9453 Rotating Gp-Pump
| 16***01 | Swashplate Stop | 2 |
| 19***53 | Rotating Group-Pump; -Brake, Hydraulic Fan | 1 |
| 1H***37 | Pin (Spring) | 2 |
6e-4216 Rotating Gp-Pump -Hydraulic Steering
| 0S***84 | Cap Screw (2 1/4" Long) | 12 |
| 18***99 | Slip Joint Group | 1 |
| 18***97 | Yoke As | 1 |
189-4710 Rotating Gp-Pump
| 16***33 | Lines Group-Secondary Steering; -Outside Nacd | 1 |
| 18***45 | Wiring Group-Secondary Steering | 1 |
| 18***10 | Rotating Group-Pump; -Hydraulic | 1 |
180-3491 Shaft Gp-Pump Drive
| 17***07 | Seal | 2 |
| 17***08 | Rotor | 1 |
| 17***09 | Retainer | 1 |
166-3310 Steering Ar-Secondary
| 16***10 | Steering Ar-Secondary | 1 |
| 17***07 | Seal | 2 |
| 17***08 | Rotor | 1 |
184-1527 Swashplate Gp
| 08***07 | Pin | 1 |
| 14***61 | Spacer; (20x128x6-mm Thk) | 1 |
| 18***27 | Swashplate Group; -Implement Pump | 1 |
260-6502 Swivel Gp -Circle Drive
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
173-1011 Swivel Gp -Circle Drive
| 17***11 | Swivel Group; -Circle Drive | 1 |
| 20***10 | Tank & Filter Group-Hydraulic | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
207-2410 Tank & Filter Gp-Hydraulic
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
207-2409 Tank & Mtg Gp-Hydraulic
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
112-2240 Manifold Gp-Control
| 11***40 | Valve & Mounting Group; -Blade Cushion | 1 |
| 24***89 | Valve Group-Shuttle | 1 |
| 24***51 | Valve Group-Control | 1 |
121-4099 Valve & Linkage Gp -6-Bank, Rh; 7-Bank, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
8x-4144 Valve & Linkage Gp -Bank4-Lh,Rh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 2 |
254-0248 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
254-0245 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
254-0244 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
254-0247 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
254-0243 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
121-4097 Valve & Linkage Gp -5-Bank, Rh, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
124-4220 Valve & Linkage Gp -Bank 4-Rh-Bank 5-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
7i-4872 Valve & Linkage Gp -Bank 4-Rh-Bank 5-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
124-4211 Valve & Linkage Gp -Bank 4-Lh,Rh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
254-0254 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
121-4090 Valve & Linkage Gp -4-Bank, Rh; 5-Bank, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
270-5006 Valve & Linkage Gp
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
265-7823 Valve & Linkage Gp
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
254-0246 Valve & Linkage Gp
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
265-7824 Valve & Linkage Gp
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
125-2235 Valve & Linkage Gp -4-Bank, Rh; 7-Bank, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
254-3378 Valve Gp-Bank 4
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
254-3375 Valve Gp-Bank 4
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8658 Valve Gp-Bank 4 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
263-6440 Valve Gp-Bank 4
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
254-3374 Valve Gp-Bank 4
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
130-3133 Valve Gp-Bank 4 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
130-3116 Valve Gp-Bank 4 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***38 | Manifold | 1 |
| 10***60 | Valve Group-Control; -Articulation | 1 |
130-3135 Valve Gp-Bank 4 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***38 | Manifold | 1 |
| 10***60 | Valve Group-Control; -Articulation | 1 |
104-8676 Valve Gp-Bank 4 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
254-3377 Valve Gp-Bank 5
| 10***09 | Seal-Integral, . Gear; Ring | 7 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
130-3134 Valve Gp-Bank 5 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***38 | Manifold | 1 |
| 10***47 | Valve Group-Control; -Bulldozer Lift, Plow | 1 |
130-3123 Valve Gp-Bank 5 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
104-8660 Valve Gp-Bank 5 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
130-3118 Valve Gp-Bank 5 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
254-3379 Valve Gp-Bank 5
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
254-3381 Valve Gp-Bank 5
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
254-3373 Valve Gp-Bank 5
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***38 | Manifold | 1 |
| 10***60 | Valve Group-Control; -Articulation | 1 |
130-3124 Valve Gp-Bank 6 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***85 | Manifold | 1 |
| 10***54 | Valve Group-Control; -Blade Tilt | 1 |
254-3380 Valve Gp-Bank 7 -Lh
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 13***50 | Valve Group-Purge; -Hydraulic Steering-Implement Signal | 1 |
| 14***08 | Plug As. | 3 |
130-3122 Valve Gp-Bank 7 -Lh
| 13***22 | Valve Group-Bank 7; -Lh | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
| 4J***77 | Seal - O - Ring (11.23mm Od) | 1 |
263-6439 Valve Gp-Bank 7
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 13***50 | Valve Group-Purge; -Hydraulic Steering-Implement Signal | 1 |
| 14***08 | Plug As. | 3 |
171-6470 Valve Gp-Check
| 10***48 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
229-7155 Valve Gp-Combination
| 10***54 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
9t-5957 Valve Gp-Combination
| 10***49 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
107-0555 Valve Gp-Control -Circle Drive
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***80 | Housing | 1 |
6e-3034 Valve Gp-Control -Blade Tip
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
130-3111 Valve Gp-Control -Bulldozer Lift, Plow, Rh
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***84 | Body | 1 |
6e-3035 Valve Gp-Control -Circle Drive
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
137-8106 Valve Gp-Control -Wing Lift, Lh
| 03***43 | Seal-O-Ring | 1 |
| 10***45 | Valve-Orifice; (Hydraulic Oil Check) | 1 |
| 13***06 | Valve Group-Control; -Wing Lift, Lh | 1 |
6e-3036 Valve Gp-Control -Sideshift
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
107-0562 Valve Gp-Control -Centershift
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
124-3455 Valve Gp-Control -Ripper-Lh
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
107-0547 Valve Gp-Control -Bulldozer Lift, Plow
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
6e-3028 Valve Gp-Control -Articulation
| 10***55 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
107-0558 Valve Gp-Control -Blade Lift
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
107-0559 Valve Gp-Control -Ripper-Lh
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
107-0554 Valve Gp-Control -Blade Tilt
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
107-0560 Valve Gp-Control -Articulation
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
130-3115 Valve Gp-Control -Blade Lift
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
137-8104 Valve Gp-Control -Wing Tilt, Lh
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 03***36 | Seal-O-Ring | 1 |
| 10***16 | Pin-Spring Stop | 1 |
119-9550 Valve Gp-Control -Ripper
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***82 | Lever As; (Blade Lift) | 1 |
128-8647 Valve Gp-Control -Blade Lift, Rh
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***84 | Body | 1 |
107-0563 Valve Gp-Control -Wheel Lean
| 10***48 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
6e-3029 Valve Gp-Control -Centershift
| 10***55 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
130-3114 Valve Gp-Control -Blade Lift
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***72 | Detent | 1 |
| 10***73 | Retainer | 4 |
130-3110 Valve Gp-Control -Blade Lift, Lh
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***72 | Detent | 1 |
107-0565 Valve Gp-Control -Blade Lift
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
6e-3030 Valve Gp-Control -Wheel Lean
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
150-6649 Valve Gp-Control -Wing Lift, Lh
| 10***44 | Valve | 1 |
| 13***70 | Sleeve | 1 |
| 15***49 | Valve Group-Control; -Wing Lift, Lh | 1 |
115-1007 Valve Gp-Control -Bulldozer Angle, Plow, Rh
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
107-0556 Valve Gp-Control -Sideshift
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
168-2210 Valve Gp-Pump Control -Pressure, Flow Compensator
| 16***10 | Valve Group-Pump Control; -Pressure, Flow Compensator-Hydraulic Oil Clg Fan Piston Pump | 1 |
| 3G***26 | Nut; (3/8-40-Thd) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
104-3122 Valve Gp-Pump Control -Pressure, Flow Compensator
| 10***22 | Valve Group-Pump Control; -Pressure, Flow Compensator-Implement, Steering | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***42 | Spring | 1 |
131-8350 Valve Gp-Purge -Implement
| 13***50 | Valve Group-Purge; -Hydraulic Steering-Implement Signal | 1 |
| 1N***02 | Seal Plug On Manifold Assembly | 4 |
| 3G***44 | Valve; (Crossover Steering) | 2 |
222-7774 Valve Gp-Relief
| 12***98 | Seat | 1 |
| 12***99 | Seat | 1 |
| 13***49 | Connector | 1 |
139-8472 Valve Gp-Relief
| 13***72 | Valve Group-Relief; -Ripper | 1 |
| 34***99 | Valve Group-Relief | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 2 |
9t-6129 Valve Gp-Relief -Steering
| 11***35 | Retainer As | 1 |
| 13***77 | Valve | 1 |
| 2A***11 | Washer; (5.5x12.3x0.8-mm Thk) | 1 |
100-6021 Valve Gp-Relief -Steering
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 13***77 | Valve | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
116-0375 Valve Gp-Relief
| 11***75 | Valve Group-Relief; -Direct Operated | 1 |
| 13***77 | Valve | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
139-8476 Valve Gp-Relief
| 11***35 | Retainer As | 1 |
| 13***77 | Valve | 1 |
| 13***76 | Valve Group-Relief | 1 |
346-3799 Valve Gp-Relief
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
| 21***94 | Coil As; (24-Volt) | 1 |
139-8477 Valve Gp-Relief
| 13***77 | Valve Group-Relief | 1 |
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
6e-4703 Valve Gp-Relief -Implement Signal
| 13***77 | Valve | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 4D***97 | Seal 15.6 mm(.614 In.) I.D. | 1 |
4t-4935 Valve Gp-Relief -Main
| 10***57 | Valve | 1 |
| 12***61 | Housing | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
4t-1860 Valve Gp-Shuttle -Implement Signal
| 03***79 | Seal-O-Ring (Id=10.82mm) | 1 |
| 03***33 | Seal-O-Ring; (12.42mm Id) | 1 |
| 18***24 | Adapter As | 1 |
131-0753 Valve Gp-Shuttle
| 13***53 | Valve Group-Shuttle; -Swing Piston Pump | 1 |
| 9C***95 | Boss-Tapped; (M10x1.5-Thd) | 5 |
183-7595 Valve Gp-Solenoid -Demand Fan
| 12***54 | Strip-Wear | 10 |
| 12***55 | Strip-Wear | 6 |
| 15***10 | Shim; (0.12-mm Thk) | 1 |
149-2610 Valve Gp-Solenoid
| 10***38 | Plate | 8 |
| 14***10 | Valve Group-Solenoid; -Axle Oil Cooler-Hydraulic Lockout | 1 |
| 1K***72 | Locknut Horn To Guard | 12 |
Implements
247-6445 Boss Gp-Drawbar
| 1D***43 | Bolt (5-1/2 In. Long 1 In. Dia.); Platform To Support Assembly | 10 |
| 24***45 | Boss Group-Drawbar | 1 |
| 2J***07 | Nut-Full; (1-8 X38.1 Thd) | 10 |
6g-4975 Circle Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***11 | Socket-Auxiliary Power; (12-Volt)(Power Port) | 1 |
| 12***78 | Locknut; (M6x1-Thd) | 2 |
6g-4980 Drawbar Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***11 | Socket-Auxiliary Power; (12-Volt)(Power Port) | 1 |
| 12***78 | Locknut; (M6x1-Thd) | 2 |
8x-6330 Plate Gp-Push
| 11***92 | Rod | 1 |
| 13***38 | Washer-Plastic; (13x31.7x0.8-mm Thk) | 2 |
| 13***44 | Latch Assem.; (Lh) | 1 |
Lubrication System
166-1329 Base Gp-Oil Filter -Engine
| 11***45 | Valve-Pump Bypass; (Engine Oil Filter) | 1 |
| 16***28 | Base Assem. | 1 |
| 16***29 | Base Group-Oil Filter; -Engine | 1 |
174-1579 Filler Gp-Engine Oil
| 17***79 | Filler Group-Engine Oil | 1 |
| 17***80 | Tube As-Filler | 1 |
| 18***54 | Bracket As | 1 |
164-2490 Filter Gp-Engine Oil
| 10***28 | Cover | 1 |
| 10***29 | Name-Plate (Lubrication), Adapter | 1 |
| 10***95 | Base Group-Oil Filter; -Engine | 1 |
174-1576 Gauge Gp-Oil Level (Dipstick) -Engine
| 17***76 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
| 17***77 | Gauge As; (Dipstick)(Engine) | 1 |
| 17***78 | Tube As-Oil | 1 |
203-2204 Lines Gp-Engine Oil Drain
| 15***37 | Elbow Group | 1 |
| 1P***19 | Coupler (Use With .75 In Hose) | 1 |
| 20***04 | Lines Group-Engine Oil Drain | 1 |
199-1096 Lines Gp-Turbocharger Oil
| 11***87 | Seal-O-Ring (23.16 mm Id) | 1 |
| 11***42 | Adapter | 1 |
| 16***79 | Tube As | 1 |
117-2746 Pump Gp-Engine Oil
| 06***61 | Seal-O-Ring (Id=40.87mm) | 1 |
| 11***03 | Tube Assem. | 1 |
| 11***46 | Pump Group-Engine Oil | 1 |
233-5220 Pump Gp-Engine Oil
| 23***20 | Pump Group-Engine Oil | 1 |
| 6D***46 | Seal-O-Ring (Id=101.27mm) | 1 |
| 6V***17 | Bolt; (M8x1.25x30-mm)(Location Z) | 4 |
Machine Arrangement
211-1771 Conversion Ar-Certification
| 12***11 | Valve & Linkage Group; -Bank 4-Lh,Rh | 1 |
| 15***03 | Control Group-Hydraulic Lockout | 1 |
| 16***10 | Steering Ar-Secondary | 1 |
211-1772 Conversion Ar-Certification
| 12***11 | Valve & Linkage Group; -Bank 4-Lh,Rh | 1 |
| 15***03 | Control Group-Hydraulic Lockout | 1 |
| 16***10 | Steering Ar-Secondary | 1 |
162-5607 General Ar
| 10***86 | Hitch Group-Articulating | 1 |
| 11***20 | Axle Group-Front | 1 |
| 12***22 | Lines Group-Lubrication | 1 |
Operator Station
171-7185 Accessory Gp-Cab -Low Profile
| 17***85 | Accessory Group-Cab; -Low Profile | 1 |
171-7186 Accessory Gp-Cab -High Profile
| 12***72 | Pad; (1035mm X 150mm) | 1 |
| 17***86 | Accessory Group-Cab; -High Profile | 1 |
| 17***48 | Air Conditioner Group; -Snow | 1 |
173-1028 Adjuster Gp-Seat
| 16***03 | Lines Group-Air Conditioner | 1 |
| 16***99 | Lines Group-Heater | 1 |
| 17***28 | Adjuster Group-Seat; -Seat | 1 |
237-3970 Air Compressor Gp-Seat
| 03***38 | Clamp | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
173-5313 Air Conditioner & Mounting Gp
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 11***40 | Bracket As-Lh | 1 |
| 17***13 | Air Conditioner & Mounting Group; -Snow | 1 |
167-8069 Air Conditioner Ar
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 11***43 | Bracket As-Rh | 1 |
| 16***69 | Air Conditioner Ar | 1 |
174-4548 Air Conditioner Gp
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 1 |
| 16***14 | Bracket As | 1 |
| 17***48 | Air Conditioner Group; -Snow | 1 |
202-7668 Armrest Gp -Lh
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 20***68 | Armrest Group; -Lh | 1 |
| 31***18 | Valve As-Pressure Relief; (Refrigerant Compressor) | 1 |
113-4245 Armrest Gp -Rh
| 11***45 | Armrest Group; -Rh | 1 |
| 29***66 | Bracket As | 1 |
| 30***36 | Handle-Screw | 1 |
202-7666 Armrest Gp -Rh
| 16***72 | Compressor Group-Refrigerant; -Air Conditioner | 1 |
| 19***41 | Guard; (Air Conditioner Compr Pulley) | 1 |
| 19***69 | Bracket-Mounting | 1 |
113-4242 Armrest Gp -Lh
| 11***42 | Armrest Group; -Lh | 1 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 1 |
| 16***13 | Bracket As | 1 |
294-5260 Bracket Gp-Mounting -Monitor
| 22***46 | Plate As; (Lh) | 1 |
| 22***29 | Plate As; (Rh) | 1 |
| 25***79 | Core As-Condenser; (Air Conditioner) | 1 |
197-4568 Compressor & Mtg Gp-Refrig
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 1 |
| 03***66 | Rod | 1 |
| 03***94 | Pin | 1 |
163-0872 Compressor Gp-Refrigerant
| 09***90 | Ring-Retaining | 1 |
| 10***04 | Bracket As | 1 |
| 11***30 | Retainer | 1 |
208-5568 Condenser & Mtg Gp-Refrigerant -A/C
| 09***90 | Ring-Retaining | 1 |
| 10***04 | Bracket As | 1 |
| 11***30 | Retainer | 1 |
167-9004 Console Gp-Operator
| 09***18 | Setscrew-Socket; (M4x0.7x6-mm) | 12 |
| 10***14 | Knob | 4 |
| 15***30 | Block | 4 |
167-8053 Console Gp-Operator
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
| 16***65 | Bracket As | 1 |
| 16***53 | Console Group-Operator | 1 |
172-5717 Control Gp-Clutch
| 09***00 | Steering Wheel | 1 |
| 11***73 | Bolt-12 Point Head; (M10x1.5x35-mm) | 4 |
| 14***95 | Nut; (13/16-20-Thd) | 1 |
152-7903 Control Gp-Hydraulic Lockout
| 15***03 | Control Group-Hydraulic Lockout | 1 |
| 25***03 | Control Group-Unprogrammed; (Caterpillar Monitoring System)(Caterpillar Monitoring System) | 1 |
7i-4720 Control Gp-Steering
| 16***65 | Guard Group-Platform; -Non-Rops | 1 |
| 19***55 | Panel Group-Instrument; -High Profile | 1 |
| 24***41 | Padlock Group; (1 On Fuel Tank Cap) (1 On Hydraulic Tank Cap) (1 On Grill Latch) | 1 |
160-6567 Control Gp-Unprgmed Monitor -Caterpillar Monitoring System
| 16***67 | Control Group-Unprgmed Monitor; -Caterpillar Monitoring System | 1 |
| 24***87 | Display Group-Monitor; -Display, Light Bar | 1 |
| 25***30 | Wiring Group-Monitor | 1 |
203-6643 Conversion Ar-Non-Rops
| 16***02 | Mounting Group-Radio | 1 |
| 20***43 | Conversion Ar-Non-Rops | 1 |
| 24***20 | Monitor As; (Light Bar) | 3 |
249-7786 Display Ar-Monitor -Cd550
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 3 |
| 19***31 | Adapter; (Compact) | 1 |
249-7783 Display Ar-Monitor -Cb420
| 22***98 | Kit-Bracket; (Grade Control) | 1 |
| 24***83 | Display Ar-Monitor; -Cb420 | 1 |
| 25***95 | Control Group-Unprogrammed; (Cb420) | 1 |
292-7974 Display Ar-Monitor -Cd700
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 6 |
| 19***31 | Adapter; (Compact) | 1 |
| 24***16 | Display Group-Monitor; (Cd700) | 1 |
249-7785 Display Gp-Monitor -Cb420
| 10***41 | Plate As | 1 |
| 10***50 | Latch As-Rh | 1 |
| 10***52 | Link-Tag-Rh | 1 |
249-7787 Display Gp-Monitor -Display, Light Bar
| 10***41 | Plate As | 1 |
| 10***49 | Latch As; (Lh) | 1 |
| 10***51 | Link-Tag-Lh | 1 |
286-0134 Display Gp-Monitor -Cd700c
| 10***53 | Bumper-Conical | 4 |
| 10***13 | Plate As | 2 |
| 12***28 | Seal; (17.2-cm Each) | 0 |
8x-4526 Door Gp-Cab -Lh
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 10***96 | Bracket As | 6 |
| 12***54 | Duct | 1 |
8x-4527 Door Gp-Cab -Low Profile
| 8X***27 | Door Group-Cab; -Low Profile | 1 |
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***43 | Cushion Kit; (Consists Of Fastener, Cushion Assem.) | 1 |
8x-4318 Door Gp-Cab -Lh
| 06***88 | Seal; (Use As Required) | 0 |
| 10***41 | Plate As | 1 |
| 10***49 | Latch As; (Lh) | 1 |
8x-4525 Door Gp-Cab -Rh
| 13***95 | Panel As | 1 |
| 16***74 | Louver As-Vent | 2 |
| 7K***01 | Nut-Speed; (44.5mm Oal) | 2 |
8x-4413 Door Gp-Cab -High Profile
| 10***53 | Bumper-Conical | 4 |
| 10***13 | Plate As | 2 |
| 12***28 | Seal; (17.2-cm Each) | 0 |
8x-4317 Door Gp-Cab -Rh
| 06***88 | Seal; (Use As Required) | 0 |
| 10***41 | Plate As | 1 |
| 10***50 | Latch As-Rh | 1 |
177-7891 Duct & Control Gp -A/C, Heater Distributor
| 17***91 | Duct & Control Group; -A/C, Heater Distributor | 1 |
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***47 | Fastener | 2 |
7i-5015 Duct Gp-Cab Air -Air Conditioner, Heater
| 17***35 | Motor Group-Electric; -Circulating Fan | 1 |
| 1B***13 | Bolt,Machine Governor And Decelerator Control | 1 |
| 1M***30 | Nut And Lock Assem.; (No. 10-32) | 2 |
8y-5959 Extension Gp-Backrest -Vinyl
| 17***34 | Fan Group-Circulating; -Defrost | 1 |
| 3E***21 | Actuator-Rocker; (Defroster) | 1 |
| 3E***25 | Lamp; (24-Volt) | 1 |
8y-5874 Extension Gp-Backrest -Cloth
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 1 |
| 13***79 | Bracket | 1 |
| 17***35 | Motor Group-Electric; -Circulating Fan | 1 |
172-6834 Fan Gp-Circulating -Front Defroster
| 10***12 | Film-Instruction; (Alternate Exit, Remove Window) | 1 |
| 15***98 | Screw-Button Head; (M3x0.5x1-mm) | 4 |
| 17***34 | Fan Group-Circulating; -Front Defroster | 1 |
170-5334 Fan Gp-Circulating -Defrost
| 11***55 | Spring-Filter | 4 |
| 13***92 | Retainer-Captive | 2 |
| 17***34 | Fan Group-Circulating; -Defrost | 1 |
172-6835 Fan Gp-Circulating -Rear Defroster
| 10***12 | Film-Instruction; (Alternate Exit, Remove Window) | 1 |
| 15***98 | Screw-Button Head; (M3x0.5x1-mm) | 4 |
| 17***35 | Fan Group-Circulating; -Rear Defroster | 1 |
170-4820 Fan Gp-Circulating
| 17***20 | Fan Group-Circulating; -Defroster, Rear-Rear | 2 |
| 3E***21 | Actuator-Rocker; (Defroster) | 1 |
| 3E***25 | Lamp; (24-Volt) | 1 |
8x-2925 Filter Gp-Cab Air
| 12***72 | Pad; (1035mm X 150mm) | 1 |
| 17***22 | Heater Group-Cab | 1 |
| 19***36 | Pad | 1 |
200-7934 Hammer & Mounting Gp -High Profile
| 03***38 | Clamp | 2 |
| 10***26 | Wheel As-Blower | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
199-2585 Hammer & Mounting Gp -Low Profile
| 16***99 | Lines Group-Heater | 1 |
| 17***52 | Heater & Mtg Group-Cab | 1 |
| 17***91 | Duct & Control Group; -A/C, Heater Distributor | 1 |
174-4552 Heater & Mtg Gp-Cab
| 15***87 | Cover | 2 |
| 17***52 | Heater & Mtg Group-Cab | 1 |
| 2G***64 | Kit-Diaphragm; (Air Horn) | 2 |
167-8395 Heater Ar-Cab
| 00***84 | Spring-Horn | 4 |
| 00***85 | Brush-Horn | 4 |
| 09***71 | Seal-Horn Button | 1 |
173-5322 Heater Gp-Cab
| 00***84 | Spring-Horn | 4 |
| 00***85 | Brush-Horn | 4 |
| 09***71 | Seal-Horn Button | 1 |
173-5307 Horn Gp-Air
| 17***07 | Horn Group-Air | 1 |
| 2A***84 | Bracket | 1 |
| 2G***67 | Washer; (10.5x60x3-mm Thk) | 1 |
5d-6998 Horn Gp-Air
| 09***78 | Pin-Spring | 1 |
| 10***24 | Kit-Indicator; (Weight Adjustment)(Suspension Seat) | 1 |
| 10***79 | Kit-Bumper; (Weight Adjustment)(Suspension Seat) | 1 |
113-5808 Housing Gp-Seat Suspension
| 11***08 | Housing Group-Seat Suspension | 1 |
| 17***41 | Module Group-Speedometer & Tach; -Cold Weather | 1 |
| 18***67 | Sensor & Mtg Group-Ground Speed | 1 |
145-1300 Installation Ar-Radio
| 11***64 | Boot | 8 |
| 14***00 | Installation Ar-Radio | 1 |
| 17***65 | Duct | 2 |
130-9432 Installation Gp-Radio
| 10***55 | Cover-Speaker | 2 |
| 10***25 | Screw-Machine; (8-32x1-In) | 8 |
| 10***14 | Knob | 4 |
185-7968 Instrument Ar -Speedometer/Tach-Eu
| 10***55 | Cover-Speaker | 2 |
| 10***25 | Screw-Machine; (8-32x1-In) | 8 |
| 10***14 | Knob | 4 |
172-5378 Insulation Gp-Weather
| 11***07 | Plate | 1 |
| 11***10 | Insulation | 1 |
| 13***09 | Pin | 2 |
172-5376 Liner Gp-Cab -Enclosed Rops
| 08***91 | Bolt; (M10x1.5x55-mm) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 2 |
177-8781 Liner Gp-Cab -High Profile
| 09***44 | Elbow | 1 |
| 11***30 | Spacer; (11.3x19.05x90-mm Thk) | 1 |
| 13***96 | Valve-Ball | 1 |
191-8695 Liner Gp-Cab -High Profile
| 19***95 | Liner Group-Cab; -Open-High Profile | 1 |
| 1P***78 | Cap | 2 |
| 2G***41 | Clamp | 2 |
167-8103 Lines Gp-Air Conditioner
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
167-8399 Lines Gp-Heater
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
197-2064 Mirror Gp-Rear View -Exterior, Enclosed Rops
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 19***64 | Mirror Group-Rear View; -Exterior, Enclosed Rops | 1 |
8x-2795 Mirror Gp-Rear View -Inside
| 11***18 | Arm | 2 |
| 12***86 | Block | 4 |
| 12***87 | Bracket | 4 |
231-6524 Mirror Gp-Rear View -Exterior, Heated
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 6 |
| 23***24 | Mirror Group-Rear View; -Exterior, Heated | 1 |
193-8212 Mirror Gp-Rear View -Exterior, Heated
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 2 |
197-2066 Mirror Gp-Rear View -Dual Interior
| 19***82 | Module Group-Speedometer & Tach | 1 |
| 19***66 | Mirror Group-Rear View; -Dual Interior | 1 |
| 7N***76 | Lamp; (24-Volt, 0.2-Ampere)(Panel) | 2 |
191-9413 Mirror Gp-Rear View -Exterior, Heated
| 19***13 | Mirror Group-Rear View; -Exterior, Heated | 1 |
| 1P***78 | Cap | 4 |
| 20***80 | Mirror | 1 |
180-9285 Module Gp-Quad Gauge
| 18***85 | Module Group-Quad Gauge | 1 |
| 24***01 | Plate As | 1 |
| 24***02 | Bracket As | 1 |
177-9741 Module Gp-Speedometer & Tach -Cold Weather
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 6 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 17***41 | Module Group-Speedometer & Tach; -Cold Weather | 1 |
190-3482 Module Gp-Speedometer & Tach
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 1 |
| 14***11 | Bolt-Socket Head; (M6x1x16-mm) | 4 |
| 19***82 | Module Group-Speedometer & Tach | 1 |
294-5261 Mounting Gp-Monitor -Cb420 Display
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 10***71 | Pin As | 2 |
| 10***53 | Mounting | 4 |
286-5697 Mounting Gp-Monitor -Cd700 Display
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 03***87 | Washer; (16.75x50.8x4.76-mm Thk) | 2 |
| 10***71 | Pin As | 2 |
244-1904 Mounting Gp-Monitor -Cb420 Display
| 10***72 | Boss | 3 |
| 14***80 | Bracket-Mounting | 1 |
| 14***96 | Plate | 1 |
167-8602 Mounting Gp-Radio
| 16***02 | Mounting Group-Radio | 1 |
| 4M***82 | Cap Screw; (Hex Head) (1/4-20x1 1/2 G 8) | 4 |
| 8C***07 | Mount; (Isolation) | 8 |
191-8692 Mounting Gp-Rops -High Profile
| 13***43 | Plate As-Lumbar | 1 |
| 17***52 | Retainer | 1 |
| 17***07 | Holder | 1 |
2a-6985 Mounting Gp-Rops -Enclosed
| 10***23 | Shaft As-Lumbar | 1 |
| 10***24 | Pan-Lumbar | 1 |
| 2A***85 | Mounting Group-Rops; -Enclosed | 1 |
150-1893 Mounting Gp-Vibration Isolator
| 15***93 | Mounting Group-Vibration Isolator | 1 |
| 16***83 | Knob-Lumbar | 1 |
| 16***24 | Cushion As-Back | 1 |
178-0605 Pan Gp-Backrest -Lumbar
| 16***83 | Knob-Lumbar | 1 |
| 17***05 | Pan Group-Backrest; -Lumbar | 1 |
| 25***28 | Plug | 3 |
108-8421 Pan Gp-Backrest -Lumbar
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
| 13***43 | Plate As-Lumbar | 1 |
| 17***52 | Retainer | 1 |
301-4173 Pan Gp-Backrest
| 10***72 | Glass; (Rear)(High Profile) | 1 |
| 11***06 | Glass; (Side) | 2 |
| 14***09 | Glass; (Lower Front) | 2 |
292-9239 Pan Gp-Backrest -Cloth
292-6402 Pan Gp-Backrest -Lumbar
| 00***81 | Ring-Retaining | 2 |
| 11***09 | Pan As-Seat | 1 |
| 11***67 | Kit-Back Tilt; (Includes Parts Marked N) | 1 |
180-7307 Pan Gp-Backrest -Cloth
| 13***43 | Plate As-Lumbar | 1 |
| 16***83 | Knob-Lumbar | 1 |
| 18***07 | Pan Group-Backrest; -Cloth | 1 |
113-5810 Pan Gp-Seat
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
8x-2375 Panel Gp-Cab
| 10***01 | Kit; (Receptacle) (12-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
8x-2385 Panel Gp-Cab -High Profile
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 2 |
| 13***63 | Harness As-Radio; (Radio) | 1 |
| 13***65 | Bumper | 1 |
197-7155 Panel Gp-Instrument -High Profile
| 19***54 | Sleeve | 1 |
| 19***55 | Panel Group-Instrument; -High Profile | 1 |
187-3188 Panel Gp-Instrument
| 13***66 | Lead-Antenna | 1 |
| 16***18 | Kit-Receptacle; (8-Pin) | 1 |
| 17***17 | Support-Radio | 1 |
331-5291 Radio Gp -Am/Fm/Wb/Cd Player
| 17***77 | Rops Group; -Low Profile | 1 |
| 17***78 | Insulation Group-Weather | 1 |
| 33***91 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
262-9163 Radio Gp -Am/Fm Cassette
| 17***78 | Insulation Group-Weather | 1 |
| 17***79 | Rops Group; -High Profile | 1 |
| 26***63 | Radio Group; -Am/Fm/Wb/Cd Player | 1 |
146-3090 Radio Gp -Am/Fm Cassette
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 1 |
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 1 |
| 14***90 | Radio Group; -Am/Fm Cassette | 1 |
210-2270 Recliner Gp-Seat
| 16***64 | Guard Group-Platform; -Open-High Profile | 1 |
| 17***51 | Rops Group; -High Profile | 1 |
| 19***55 | Panel Group-Instrument; -High Profile | 1 |
203-6642 Rops Ar -High Profile
| 10***72 | Glass; (Rear)(High Profile) | 1 |
| 11***98 | Rops Group; -High Profile, Open | 1 |
| 15***59 | Film-Instruction; (Do Not Drill, Weld Rops) | 2 |
179-3581 Rops Ar -Low Profile
| 15***12 | Plate-Warning; (Ops Certification, Read Omm) | 1 |
| 15***59 | Film-Instruction; (Do Not Drill, Weld Rops) | 2 |
| 17***76 | Liner Group-Cab; -Enclosed Rops | 1 |
161-1141 Rops Ar -High Profile
| 15***12 | Plate-Warning; (Ops Certification, Read Omm) | 1 |
| 16***41 | Rops Ar; -High Profile | 1 |
| 18***56 | Plate Group-Certification | 1 |
172-5377 Rops Gp -Low Profile
| 15***59 | Film-Instruction; (Do Not Drill, Weld Rops) | 2 |
| 17***77 | Rops Group; -Low Profile | 1 |
| 17***31 | Wiper Group-Window; -Front-High Profile | 1 |
117-4698 Rops Gp -High Profile
| 11***98 | Rops Group; -High Profile, Open | 1 |
| 15***12 | Plate-Warning; (Ops Certification, Read Omm) | 1 |
| 18***56 | Plate Group-Certification | 1 |
177-8779 Rops Gp -High Profile
| 0T***44 | Bolt (1.25" Long) | 1 |
| 17***79 | Rops Group; -High Profile | 1 |
| 20***88 | Bolt; (7/16-20) (44.5mml) | 1 |
173-2751 Rops Gp
| 13***03 | Screen Group-Sun | 1 |
| 13***05 | Plate As | 1 |
| 17***51 | Rops Group; -High Profile | 1 |
173-6756 Rops Gp -High Profile
| 17***56 | Rops Group; -Enclosed, High Profile | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 1L***80 | Bolt; (7/16-20x1.5-In) | 1 |
139-4612 Screen Gp-Sun -Rear
| 09***78 | Pin-Spring | 1 |
| 09***14 | Pin, Clevis | 1 |
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
222-0345 Seat Belt Gp -Retractable
| 0T***44 | Bolt (1.25" Long) | 1 |
| 17***84 | Extension Group-Backrest; (Cloth) | 1 |
| 17***37 | Spacer; (11.7x19.8x20.3-mm Thk)(Lh Seat Side) | 1 |
156-1148 Seat Belt Gp -Retractable
| 09***78 | Pin-Spring | 1 |
| 09***14 | Pin, Clevis | 1 |
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
175-1504 Seat Gp -Cloth
| 09***43 | Pin-Cotter | 2 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 8 |
| 16***25 | Cushion As | 1 |
114-1183 Seat Gp -Cloth, Lumbar
| 0T***44 | Bolt (1.25" Long) | 1 |
| 11***83 | Seat Group; -Cloth, Lumbar | 1 |
| 17***84 | Extension Group-Backrest; (Cloth) | 1 |
180-7306 Seat Gp -Cloth
| 11***05 | Seat Group-Suspension; -Vinyl | 1 |
| 18***06 | Seat Group; -Cloth | 1 |
| 9X***41 | Screw-Truss Head (M10x1.50x20mm); (Truss Head) (M10x1.5x20mm) | 6 |
301-4174 Seat Gp -Cloth
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
114-1185 Seat Gp -Vinyl, Lumbar
| 09***43 | Pin-Cotter | 2 |
| 11***85 | Seat Group; -Vinyl, Lumbar | 1 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 8 |
156-7778 Seat Gp-Suspension -Cloth, Lumbar
| 10***03 | Fastener | 20 |
| 10***94 | Kit-Tether Belt; (Suspension Seat)(Seat Suspension) | 1 |
| 10***95 | Kit-Suspension Roller; (Suspension Seat)(Seat Suspension) | 1 |
154-5732 Seat Gp-Suspension -Cloth
| 09***81 | Spacer; (10.5x20x10.0mm Thk) | 1 |
| 15***32 | Seat Group-Suspension; -Cloth | 2 |
| 15***29 | Grommet | 1 |
200-3814 Seat Gp-Suspension -Cloth, Air
| 10***17 | Bumper | 4 |
| 12***57 | Shaft | 2 |
| 12***28 | Kit-Roller; (Incls Parts Marked S) | 1 |
112-9104 Seat Gp-Suspension -Cloth
| 11***04 | Seat Group-Suspension; -Cloth | 1 |
| 15***58 | Seat Group-Suspension; -Cloth, Lumbar | 1 |
| 16***25 | Kit-Slider Block; (Seat) | 1 |
112-9105 Seat Gp-Suspension -Vinyl
| 11***05 | Seat Group-Suspension; -Vinyl | 1 |
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
8y-4194 Seat Gp-Suspension -Cloth
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
8y-4951 Seat Gp-Suspension -Vinyl
| 15***58 | Seat Group-Suspension; -Cloth, Lumbar | 1 |
| 15***59 | Suspension Group-Seat; -Air | 1 |
| 16***25 | Kit-Slider Block; (Seat) | 1 |
155-5958 Seat Gp-Suspension -Cloth, Lumbar
| 12***18 | Cover | 1 |
| 12***01 | Seal | 1 |
| 12***08 | Tube As | 2 |
174-4546 Support Gp-Seat
| 10***03 | Fastener | 26 |
| 14***26 | Film-Instruction; (Seat Adjustment) | 1 |
| 16***35 | Spring | 1 |
273-2820 Suspension Gp-Seat
| 15***70 | Nut; (1/2-20-2b-Thd) | 1 |
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 27***20 | Suspension Group-Seat | 1 |
155-5959 Suspension Gp-Seat -Air
| 12***21 | Bolt | 3 |
| 15***59 | Suspension Group-Seat; -Air | 1 |
| 2D***06 | Pin | 1 |
113-5800 Suspension Gp-Seat
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
| 1H***23 | Packing,Preformed Part Of Kit P/N 5r***25 | 1 |
| 4D***35 | Seat-Spring | 1 |
5d-4382 Valve Gp-Air Control -Parking Brake
| 10***45 | Cover | 1 |
| 10***65 | Pad; (Round) | 1 |
| 14***95 | Hose; (650-cm Each) | 0 |
8x-2650 Valve Gp-Air Control
| 14***95 | Hose; (650-cm Each) | 0 |
| 3V***16 | Nozzle As; (Rear) | 1 |
| 4D***88 | Clip-(Slot To Fit Fastener M10 Or 3/8) | 1 |
188-9250 Valve Gp-Solenoid
| 10***58 | Nut; (10x32-mm) | 2 |
| 10***46 | Stop-Slide | 2 |
| 13***32 | Latch As | 1 |
185-0008 Valve Gp-Solenoid
| 10***58 | Nut; (10x32-mm) | 2 |
| 10***46 | Stop-Slide | 2 |
| 13***32 | Latch As | 1 |
8x-9675 Washer Gp-Window -Front
| 13***33 | Window Group-Cab; -Side Sliding-Low Profile | 2 |
| 8X***75 | Washer Group-Window; -Front-Low Profile | 1 |
8x-9680 Washer Gp-Window -Rear
| 13***32 | Window Group-Cab; -Side Sliding-High Profile | 2 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
134-8232 Window Gp-Cab -Side Sliding High Profile
| 12***08 | Spacer; (10.31x17.45x50.8-mm Thk) | 1 |
| 12***09 | Plate | 1 |
| 12***10 | Plate | 1 |
134-8233 Window Gp-Cab
| 12***08 | Spacer; (10.31x17.45x50.8-mm Thk) | 1 |
| 12***09 | Plate | 1 |
| 12***10 | Plate | 1 |
150-5106 Window Gp-Cab -Rh
| 15***06 | Window Group-Cab; -Rh | 1 |
| 17***21 | Wiper Group-Window; -Rear-High Profile | 1 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
150-5107 Window Gp-Cab -Lh
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 13***11 | Motor Group-Window Wiper; (24-Volt, 2-Speed)(Front) | 1 |
| 15***07 | Window Group-Cab; -Lh | 1 |
139-6128 Window Gp-Cab -Side Sliding
| 13***28 | Window Group-Cab; -Side Sliding-Low Profile | 1 |
| 15***06 | Window Group-Cab; -Rh | 1 |
| 15***07 | Window Group-Cab; -Lh | 1 |
139-6129 Window Gp-Cab -Side Sliding High Profile
| 13***29 | Window Group-Cab; -Side Sliding High Profile | 1 |
| 17***20 | Wiper Group-Window; -Rear-Low Profile | 1 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
126-0961 Window Gp-Vent -Vent
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***85 | Wiper Group-Window | 1 |
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
177-8830 Wiper Ar-Window -Rear
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
| 12***55 | Blade As-Wiper; (335-mm)(High Profile Front Lower) | 2 |
177-8831 Wiper Ar-Window -Rear
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***85 | Wiper Group-Window | 1 |
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
173-5320 Wiper Gp-Window -Rear
| 06***60 | Ring-Retaining | 1 |
| 15***14 | Adapter; (4-Ft)(Outside) | 4 |
| 17***20 | Wiper Group-Window; -Rear-Low Profile | 1 |
177-8784 Wiper Gp-Window -Intermittent, Front
| 17***84 | Wiper Group-Window; -Intermittent, Front | 1 |
| 4T***11 | Edge-Cutting | 2 |
172-6830 Wiper Gp-Window -Front
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***85 | Knob-Wiper Switch; (Rear) | 1 |
173-5321 Wiper Gp-Window -Rear
| 17***21 | Wiper Group-Window; -Rear-High Profile | 1 |
| 1J***62 | Bolt-Plow | 20 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 42 |
172-6831 Wiper Gp-Window -Front
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 10***06 | Receptacle Kit; (Includes Wedge And Receptacle Assem.) | 1 |
| 11***85 | Knob-Wiper Switch; (Rear) | 1 |
114-6685 Wiper Gp-Window
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 1 |
| 11***85 | Wiper Group-Window | 1 |
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
Power Train
2p-6899 Case Gp-Transmission
| 0L***61 | Pin-Dowel; (9.4mm X 22mm) | 2 |
| 1P***94 | Sleeve | 4 |
| 2P***19 | Tube | 1 |
6g-1740 Chain Gp-Drive
| 6G***01 | Chain Group | 4 |
| 6G***02 | Link-Connecting; (Master) | 1 |
| 6G***40 | Chain Group | 1 |
173-5334 Control Gp-Differential Lock
| 13***72 | Hose As | 1 |
| 17***34 | Control Group-Differential Lock | 1 |
| 17***05 | Valve & Mtg Group-Diff Lock | 1 |
8e-4132 Control Gp-Transmission Hyd
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 4 |
| 11***75 | Valve Group-Relief; -Main | 1 |
| 1T***16 | Bolt; (5/16-18x0.75-In)(12 Point Hd) | 1 |
231-6018 Coupling Gp-Torsional
| 0S***79 | Bolt 5.08 cm(2 In.) Long | 1 |
| 20***56 | Coupling; (Flywheel) | 1 |
| 23***18 | Coupling Group-Torsional | 1 |
227-2564 Cover Gp-Shipping
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 6 |
| 19***41 | Cover-Shipping | 1 |
8d-4290 Differential & Bevel Gear Gp
| 03***60 | Cup-Roller Bearing | 1 |
| 03***61 | Cone-Roller Bearing | 1 |
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 6 |
8d-4300 Differential Gp
| 11***09 | Spider | 1 |
| 17***21 | Bearing-Sleeve | 1 |
| 1A***51 | Bolt,Machine Hydraulic Tank Mtg | 8 |
204-5851 Filler Gp-Power Train Oil
| 20***51 | Filler Group-Power Train Oil | 1 |
| 20***06 | Tube As | 1 |
| 20***07 | Tube As | 1 |
172-4662 Filter Gp-Oil -Transmission
| 17***62 | Filter Group-Oil; -Transmission | 1 |
| 1R***19 | Filter Element As-Oil; (Standard Efficiency)(Power Train) | 1 |
| 2J***56 | Ring-Retaining | 1 |
5t-7158 Drive Gp-Final
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 16 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 10 |
| 1D***09 | Bolt Canopy Assembly To Mounting Brackets; Bolt-Canopy Assembly To Mounting Brackets | 40 |
186-4872 Gear & Case Gp-Transfer
| 0L***15 | Bolt 88.90 mm(3.50 In.) N.F. | 1 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 7 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 11 |
6i-9851 Lines Gp-Power Train Oil
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 2 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 4 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
142-6206 Mounting Gp-Wheel
| 14***06 | Mounting Group-Wheel | 1 |
| 5D***64 | Washer-Hard; (34x57x8-mm Thk) | 60 |
| 5D***65 | Nut-Full; (1-5/16-12-Thd) | 60 |
2p-5800 Planetary Gp-Transmission
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 8 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 30 |
178-9178 Pump Gp-Gear -2 Section
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 4 |
| 17***75 | Cover | 1 |
194-5867 Tandem & Cover Gp
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 2 |
| 10***36 | Cover | 2 |
| 19***67 | Tandem & Cover Group | 1 |
231-6016 Transmission Ar
| 18***16 | Transmission Ar | 1 |
| 23***16 | Transmission Ar | 1 |
| 23***18 | Coupling Group-Torsional | 1 |
183-6616 Transmission Ar
| 17***62 | Filter Group-Oil; -Transmission | 1 |
| 17***78 | Pump Group-Gear; -2 Section | 1 |
| 18***16 | Transmission Ar | 1 |
174-3705 Valve & Mtg Gp-Diff Lock
| 14***16 | Manifold | 1 |
| 15***64 | Valve Group-Solenoid | 1 |
| 17***05 | Valve & Mtg Group-Diff Lock | 1 |
2p-4548 Valve Gp-Control
| 1P***74 | Pin-Valve Spring | 1 |
| 2P***48 | Valve As | 1 |
| 3H***56 | Pin | 1 |
2p-5816 Valve Gp-Selector & Press Cont -Modulating Reducing-Speed
| 1L***69 | Ring-Retaining | 1 |
| 1S***36 | Retainer | 1 |
| 1S***38 | Ring-Retaining | 1 |
2p-5814 Valve Gp-Selector & Press Cont -Direction
| 1P***85 | Spool | 1 |
| 1T***16 | Bolt; (5/16-18x0.75-In)(12 Point Hd) | 4 |
| 2B***58 | Plug--To Block Upper Front Air Manifold | 1 |
8e-4130 Valve Gp-Pilot -Speed Select
| 2H***65 | Pin (Spring) | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
| 3P***62 | Stop | 1 |
244-4120 Valve Gp-Pilot -Pressure, Flow Compensator
| 24***20 | Valve Group-Pilot; -Pressure, Flow Compensator | 1 |
| 8T***42 | Bolt-Socket Hd; (M6 X 1.0 X 30) | 4 |
| 9X***80 | Seal-O-Ring | 3 |
115-1375 Valve Gp-Relief -Main
| 11***24 | Body-Relief Valve | 1 |
| 11***75 | Valve Group-Relief; -Main | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 10 |
8p-1100 Valve Gp-Selector & Press Cont -Manual Modulating-Differential-Speed
| 1P***61 | Spool-Differential Safety | 1 |
| 1T***16 | Bolt; (5/16-18x0.75-In)(12 Point Hd) | 7 |
| 2H***32 | Seal--To Bottom Cover On Selector Valve | 1 |
154-3064 Valve Gp-Solenoid
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 14***50 | Cartridge As | 1 |
8e-4131 Valve Gp-Transmission Control
| 0A***64 | Clip Diode Uoc:Bsv,Bsx | 1 |
| 2P***14 | Valve Group; -Direction | 1 |
| 2P***16 | Valve Group; -Modulating Reducing-Speed | 1 |
157-1739 Wheel & Tire Ar
| 15***38 | Wheel & Tire Group | 6 |
| 15***39 | Wheel & Tire Ar | 1 |
152-3965 Wheel & Tire Ar
| 14***17 | Wheel & Tire Group | 6 |
| 15***65 | Wheel & Tire Ar | 1 |
163-6129 Wheel & Tire Ar
| 13***37 | Tire; (23.5-25) | 1 |
| 16***29 | Wheel & Tire Ar | 1 |
| 16***30 | Wheel & Tire Group | 6 |
152-3971 Wheel & Tire Ar
| 14***19 | Wheel & Tire Group | 6 |
| 15***71 | Wheel & Tire Ar | 1 |
295-0033 Wheel & Tire Ar
| 29***32 | Wheel & Tire Group | 6 |
| 29***33 | Wheel & Tire Ar | 1 |
152-3988 Wheel & Tire Ar
| 14***33 | Wheel & Tire Group | 6 |
| 15***88 | Wheel & Tire Ar | 1 |
268-9657 Wheel & Tire Ar
| 26***57 | Wheel & Tire Ar | 1 |
| 26***59 | Wheel & Tire Group | 6 |
191-2313 Wheel & Tire Ar
| 19***12 | Wheel & Tire Group | 6 |
| 19***13 | Wheel & Tire Ar | 1 |
252-0559 Wheel & Tire Ar
| 25***58 | Wheel & Tire Group | 6 |
| 25***59 | Wheel & Tire Ar | 1 |
167-0694 Wheel & Tire Ar
| 16***93 | Wheel & Tire Group | 6 |
| 16***94 | Wheel & Tire Ar | 1 |
200-2675 Wheel & Tire Ar
| 20***74 | Wheel & Tire Group | 6 |
| 20***75 | Wheel & Tire Ar | 1 |
205-2197 Wheel & Tire Ar
| 20***97 | Wheel & Tire Ar | 1 |
| 20***98 | Wheel & Tire Group | 6 |
152-3974 Wheel & Tire Ar
| 14***22 | Wheel & Tire Group | 6 |
| 15***74 | Wheel & Tire Ar | 1 |
152-4000 Wheel & Tire Ar
| 14***34 | Wheel & Tire Group | 6 |
| 15***00 | Wheel & Tire Ar | 1 |
173-0978 Wheel & Tire Ar
| 17***78 | Wheel & Tire Ar | 1 |
| 17***80 | Wheel & Tire Group | 6 |
152-3967 Wheel & Tire Ar
| 14***18 | Wheel & Tire Group | 6 |
| 15***67 | Wheel & Tire Ar | 1 |
152-3979 Wheel & Tire Ar
| 14***26 | Wheel & Tire Group | 6 |
| 15***79 | Wheel & Tire Ar | 1 |
169-8566 Wheel & Tire Ar
| 16***66 | Wheel & Tire Ar | 1 |
| 17***38 | Wheel & Tire Group | 6 |
258-6477 Wheel & Tire Ar
| 25***77 | Wheel & Tire Ar | 1 |
| 25***41 | Wheel & Tire Group | 6 |
197-7918 Wheel & Tire Ar
| 19***16 | Wheel & Tire Group | 6 |
| 19***18 | Wheel & Tire Ar | 1 |
152-3977 Wheel & Tire Ar
| 14***24 | Wheel & Tire Group | 6 |
| 15***77 | Wheel & Tire Ar | 1 |
152-3975 Wheel & Tire Ar
| 14***23 | Wheel & Tire Group | 6 |
| 15***75 | Wheel & Tire Ar | 1 |
258-6491 Wheel & Tire Ar
| 25***91 | Wheel & Tire Ar | 1 |
| 25***42 | Wheel & Tire Group | 6 |
152-4008 Wheel & Tire Ar
| 14***38 | Wheel & Tire Group | 6 |
| 15***08 | Wheel & Tire Ar | 1 |
152-3987 Wheel & Tire Ar
| 14***32 | Wheel & Tire Group | 6 |
| 15***87 | Wheel & Tire Ar | 1 |
171-4714 Wheel & Tire Ar
| 17***13 | Wheel & Tire Group | 6 |
| 17***14 | Wheel & Tire Ar | 1 |
196-4928 Wheel & Tire Ar
| 19***27 | Wheel & Tire Group | 6 |
| 19***28 | Wheel & Tire Ar | 1 |
157-1738 Wheel & Tire Gp
| 11***63 | Tire; (23.5-R25) | 1 |
| 15***38 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
142-6424 Wheel & Tire Gp
| 12***26 | Tire; (23.50-25 12pr D/L-2a) | 1 |
| 14***24 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
163-6130 Wheel & Tire Gp
| 13***37 | Tire; (23.5-25) | 1 |
| 16***30 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
142-6433 Wheel & Tire Gp
| 14***33 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
| 2D***43 | Seal-O-Ring | 1 |
167-0693 Wheel & Tire Gp
| 10***11 | Tire; (18-R25) | 1 |
| 14***33 | Wheel Group | 1 |
| 16***93 | Wheel & Tire Group | 1 |
295-0032 Wheel & Tire Gp
| 14***92 | Tire; (23.5-25) | 1 |
| 22***85 | Wheel Group | 1 |
| 29***32 | Wheel & Tire Group | 1 |
142-6426 Wheel & Tire Gp
| 12***28 | Tire; (23.50-25 12pr D/L-3a) | 1 |
| 14***26 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
142-6423 Wheel & Tire Gp
| 12***25 | Tire; (23.5-25)(23.50-25 12pr D/L-2a) | 1 |
| 14***23 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
142-6438 Wheel & Tire Gp
| 14***36 | Tire; (23.5-R25) | 1 |
| 14***38 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
173-0980 Wheel & Tire Gp
| 14***33 | Wheel Group | 1 |
| 17***80 | Wheel & Tire Group | 1 |
| 17***83 | Tire; (18.00-25 16pr E/L2) | 1 |
191-2312 Wheel & Tire Gp
| 16***62 | Tire; (23.5-R25) | 1 |
| 19***12 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
142-6418 Wheel & Tire Gp
| 14***52 | Tire; (18.00-25 12pr E-2 404-799) | 1 |
| 14***33 | Wheel Group | 1 |
| 14***18 | Wheel & Tire Group | 1 |
142-6432 Wheel & Tire Gp
| 14***32 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
| 22***86 | Flange As | 1 |
142-6425 Wheel & Tire Gp
| 12***30 | Tire; (23.5-25)(23.50-25 12pr D/L-3a) | 1 |
| 14***25 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
258-6541 Wheel & Tire Gp
| 22***85 | Wheel Group | 1 |
| 25***83 | Tire; (23.5-R25) | 1 |
| 25***41 | Wheel & Tire Group | 1 |
268-9659 Wheel & Tire Gp
| 14***33 | Wheel Group | 1 |
| 26***87 | Tire; (23.5-25) | 1 |
| 26***59 | Wheel & Tire Group | 1 |
197-7916 Wheel & Tire Gp
| 19***16 | Wheel & Tire Group | 1 |
| 19***68 | Tire; (23.5-R25) | 1 |
| 22***85 | Wheel Group | 1 |
252-0558 Wheel & Tire Gp
| 20***32 | Tire; (23.5-R25) | 1 |
| 22***85 | Wheel Group | 1 |
| 25***58 | Wheel & Tire Group | 1 |
200-2674 Wheel & Tire Gp
| 14***34 | Wheel Group | 1 |
| 1J***87 | Flange | 2 |
| 20***74 | Wheel & Tire Group | 1 |
142-6434 Wheel & Tire Gp
| 14***34 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
| 2D***43 | Seal-O-Ring | 1 |
142-6419 Wheel & Tire Gp
| 14***53 | Tire; (18.00-25 12pr E-2) | 1 |
| 14***33 | Wheel Group | 1 |
| 14***19 | Wheel & Tire Group | 1 |
142-6417 Wheel & Tire Gp
| 14***38 | Tire; (18-25) | 1 |
| 14***33 | Wheel Group | 1 |
| 14***17 | Wheel & Tire Group | 1 |
171-4713 Wheel & Tire Gp
| 12***31 | Tire; (23.5-25) | 1 |
| 17***13 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
196-4927 Wheel & Tire Gp
| 10***59 | Tire; (23.5-R25) | 1 |
| 19***27 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
205-2198 Wheel & Tire Gp
| 20***36 | Tire; (23.5-25 20pr L-5) | 1 |
| 20***98 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
258-6542 Wheel & Tire Gp
| 22***85 | Wheel Group | 1 |
| 25***84 | Tire; (23.5-R25) | 1 |
| 25***42 | Wheel & Tire Group | 1 |
142-6422 Wheel & Tire Gp
| 12***27 | Tire; (23.5-25)(23.50-25 12pr D/L-2a) | 1 |
| 14***22 | Wheel & Tire Group | 1 |
| 22***85 | Wheel Group | 1 |
170-0438 Wheel & Tire Gp
| 17***38 | Wheel & Tire Group | 1 |
| 17***39 | Tire; (25.5 R25 * Egl-4) | 1 |
| 22***85 | Wheel Group | 1 |
150-5143 Wheel Ar
| 15***42 | Wheel Group | 6 |
| 15***43 | Wheel Ar | 1 |
151-0288 Wheel Ar
| 15***44 | Wheel Group | 6 |
| 15***88 | Wheel Ar | 1 |
150-5144 Wheel Gp
| 15***44 | Wheel Group | 1 |
| 22***85 | Wheel Group | 1 |
| 2D***43 | Seal-O-Ring | 1 |
150-5142 Wheel Gp
| 14***33 | Wheel Group | 1 |
| 15***42 | Wheel Group | 1 |
| 2D***43 | Seal-O-Ring | 1 |
142-6233 Wheel Gp
| 14***33 | Wheel Group | 1 |
| 1J***87 | Flange | 2 |
| 7D***69 | Ring-Lock | 1 |
226-1885 Wheel Gp
| 22***85 | Wheel Group | 1 |
| 22***86 | Flange As | 1 |
| 22***02 | Rim As; (19.5x25) | 1 |
Service Equipment And Supplies
136-4832 Box Gp-Tool
| 13***32 | Box Group-Tool | 1 |
| 19***68 | Coupler-Grease | 1 |
| 19***69 | Hose As | 1 |
183-5812 Film Gp
| 18***12 | Film Group | 2 |
| 19***38 | Film; (Warning) (Coolant) (To Right Side Of Radiator Fill Cover) | 1 |
| 19***86 | Film; (Safety) (To Right And Left Of Fuel Tank) | 2 |
207-1764 Film Gp -Vhp
| 19***86 | Film; (Safety) (To Right And Left Of Fuel Tank) | 2 |
| 19***74 | Film-Stripe; (Yellow, Reflective)(Fender) | 6 |
| 19***67 | Plate | 2 |
207-1980 Film Gp -Non Vhp
| 15***20 | Plate-Rops/Fops | 1 |
| 20***26 | Plate-Warning; (No Clearance) | 2 |
| 20***80 | Film Group; -Non Vhp | 1 |
8f-9866 Grease Gun Gp
| 15***26 | Plate-Warning-Rops/Fops; (Rops, Fops) | 1 |
| 20***33 | Plate-Warning; (No Clearance) | 2 |
| 21***37 | Film-Warning; (Cable Connection) | 1 |
206-1404 Plate & Film Gp -French
| 20***21 | Plate-Main Frame; (Do Not Drill Or Weld) | 1 |
| 20***29 | Film-Warning; (Hazard, Read Omm) | 1 |
| 20***32 | Film-Warning; (Spring Loaded Pin, Read Manual) | 1 |
171-5838 Plate & Film Gp
| 15***24 | Plate-Rops/Fops | 1 |
| 17***38 | Plate & Film Group | 1 |
| 20***31 | Plate-Warning; (No Clearance) | 2 |
249-6529 Plate & Film Gp -Turkish
| 24***29 | Plate & Film Group; -Turkish | 1 |
206-1406 Plate & Film Gp -Portuguese
| 20***06 | Plate & Film Group; -Portuguese | 1 |
206-1405 Plate & Film Gp -Spanish
| 18***30 | Strap Wrench Assem. | 1 |
| 1P***45 | Gauge Group-Pressure | 1 |
| 1S***59 | Socket Wrench (1/2 Inch Opening) | 1 |
192-1434 Plate & Film Gp -Reflector
| 15***21 | Plate-Rops/Fops | 1 |
| 19***34 | Plate & Film Group; -Reflector-Eu | 1 |
| 20***27 | Plate-Warning; (No Clearance) | 2 |
206-1407 Plate & Film Gp -German
| 20***07 | Plate & Film Group; -German | 1 |
211-0617 Tool Gp-Hand
| 21***17 | Tool Group-Hand | 1 |
Work Tools
107-3414 Bit Gp
| 10***14 | Bit Group | 1 |
| 2A***38 | Bolt-(3/4" X 2-1/4")-Rops Mounting Bracket To Fender | 4 |
| 2B***15 | Bolt 165 mm(6.5 In.)Long; 165.1mm(6.5 In.)Long | 4 |
8w-8424 Blade Gp
| 12***75 | Cam As | 2 |
| 12***73 | Link As | 2 |
| 1K***72 | Locknut Horn To Guard | 2 |
107-3423 Edge Gp-Cutting
| 10***23 | Edge Group-Cutting | 1 |
| 1D***12 | Bolt 4 In. (102.0 mm) Long Rear Bracket Assembly To Frame | 4 |
| 25***50 | Plate | 1 |
107-3429 Edge Gp-Cutting
| 10***29 | Edge Group-Cutting | 1 |
| 11***64 | Cylinder Group-Ripper | 1 |
| 20***01 | Mounting Group-Ripper | 1 |
8d-4885 Lift Gp-Blade
| 19***86 | Film; (Safety) (To Right And Left Of Fuel Tank) | 2 |
| 1K***72 | Locknut Horn To Guard | 8 |
| 2K***03 | Washer (Bar) | 1 |
207-2801 Mounting Gp-Ripper
| 11***58 | Pin; (G.E.T.) | 1 |
| 11***59 | Retainer Assembly; (G.E.T.) | 1 |
| 20***01 | Mounting Group-Ripper | 1 |
258-8447 Mounting Gp-Snow Wing
| 25***47 | Mounting Group-Snow Wing | 1 |
| 5M***62 | Bolt; (3/8-16x0.75-In) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
207-2428 Ripper Ar
| 20***28 | Ripper Ar | 1 |
| 20***26 | Film-Stripe | 2 |
| 20***28 | Film-Caterpillar | 1 |
8j-5274 Ripper Gp
| 11***24 | Film-Vhp; (On Both Sides Of Platform) | 2 |
| 11***52 | Plate & Film Group; -Engine Information | 1 |
| 23***21 | Software Group-Power Train; (Variable Horsepower) | 1 |
8j-2189 Tooth Gp-Ripper
| 11***52 | Plate & Film Group; -Engine Information | 1 |
| 8J***89 | Tooth Group-Ripper; -Straight | 1 |
16H serial number reference
The PIN/serial plate on a 16H is stamped on the frame, most commonly on the right side of the front frame near the cab or on the firewall inside the engine compartment; older units may also carry a plate near the articulation joint. Read the first three characters as the serial prefix (model/plant code) and the remaining digits as the sequential unit number within that prefix run; on 17-character full PINs the same 3-letter prefix plus 5-digit sequence sits in the last 8 characters. Always cross-check the prefix against the engine and attachment arrangement plates, since a 16H's drawbar/circle/moldboard, hydraulic arrangement, and (for later serials) engine fitment can vary within the same prefix run.
| Prefix | Identifies | Notes |
|---|---|---|
| 6ZJ | 16H Standard, North America-built (earlier production run) | Earlier-build 16H run, assembled in the US. Documented serials in this run span from the low 00100s into the 01000s, with dated used-equipment records from 1996 through 1999. Fitted with the Cat 3406-family turbocharged diesel (factory literature cites 3406/3406C/3406TA across this run) rated near 1850 rpm. Power shift transmission with load-sensing hydraulics; exact TA/C/E engine suffix and gear count vary by build date within the run - confirm against the machine's own engine arrangement plate. |
| ATS | 16H Standard, North America-built, later production run (sometimes called 16H Series Two in the trade) | Later-build 16H run following the 6ZJ range, continuing to roughly 2006-2007. Caterpillar's own parts and service manual set for this serial range (separate sections covering brakes, circle, hydraulics and more) is titled for the machine powered by the 3196 engine, not the 3406 family. This reflects a genuine mid-life running engineering change: Cat's sibling H-series graders received comparable engine updates in their own later production runs, and a factory spec sheet for this configuration lists the 3196 ATAAC/ETA rated near 2000 rpm, about 265-295 hp depending on gear. Confirm exact engine suffix and rated output against the machine's own engine arrangement plate, since detail varies within the ATS run. |
Frequently asked questions
What engine does the Caterpillar 16H motor grader use?
Two distinct engines run under the 16H name, so confirm which one is fitted before ordering parts. The standard 16H uses a Cat 3196 ETA, turbocharged and air-to-air aftercooled, 11.9 L inline-six rated about 197-213 kW (265-285 hp) depending on gear range. The heavier 16H ES / Standard Mining configuration carries the larger Cat 3406 DITA, a 14.6 L inline-six rated around 205 kW (275 hp). Read the engine serial plate rather than assuming from the machine's serial prefix alone.
What is the operating weight of the Caterpillar 16H?
Standard operating weight is about 24,740 kg (54,550 lb) on the 3196-engine configuration and roughly 24,748 kg (54,560 lb) on the 3406-engine ES/Standard Mining configuration. With full ballast and attachments fitted, maximum operating weight reaches about 31,592 kg (69,648 lb). Exact figures vary by configuration, tires, and attachments fitted.
What replaced the Caterpillar 16H motor grader?
Caterpillar replaced the 16H with the 16M when its M-series graders arrived around 2007, adding joystick steering controls and a Cat C13 ACERT engine in place of the 16H's mechanical/hydraulic controls. The 16H itself had replaced the 16G, which was built from 1987 to 1995.
What 16H owners discuss
What engine does the Cat 16H actually run, and does it change by version?
Two distinct engines show up under the 16H name, so confirm before assuming parts commonality. The standard 16H (the mining/haul-road grader that followed the 16G) runs the Cat 3196 ETA, a turbocharged-aftercooled 11.9 L inline-six rated around 285 hp (213 kW) at 2000 rpm. The heavier 16H ES variant carries the larger Cat 3406 DITA, a 14.6 L inline-six rated closer to 275 hp (205 kW). Don't assume one engine family across the whole 16H line - read the engine serial plate and match it to the correct parts book before ordering anything.
Is the 16H a torque-converter or direct-drive grader, and what's the deal with the circle slip clutch?
The 16H uses a direct-drive power shift transmission into a planetary final drive, eight speeds forward and reverse, not a torque-converter drive. Mechanics who wrench on these graders point to the circle drive slip clutch as the thing to watch: it's a shimmed clutch pack meant to slip under shock load (blade catching a buried rock or curb) so the hit doesn't transfer into the drawbar, circle and A-frame. If the pack seizes or gets over-tightened so it stops slipping, the next hard hit goes straight into the drivetrain and breaks shafts - operators describe it as an unmistakable failure once it happens, and a broken shaft isn't something you weld back together. Adjustment is just pulling a shim from the retainer pack, but the sequence matters: vertical play first, then pinion-to-tooth contact, then shoe adjustment, then the slip clutch last.
What should I know about the 16H's hydraulic system - any known quirks?
The 16H runs an axial-piston, load-sensing pump feeding PPPC (proportional priority pressure-compensated, sometimes called triple-PC) valves, roughly 250 L/min (66 gal/min) against a 24,100 kPa (3500 psi) relief setting - exact flow varies by configuration. That setup gives good multi-function feel on the levers, but the system is sensitive to oil cleanliness; contaminated hydraulic oil is a common cause of circle or blade response that gets blamed on the valves instead. On steering, watch for a whining or knocking cushion valve when the wheel is run to full lock each direction with the engine running - left alone it's flagged as an early sign of steering failure, worth checking on any machine you're evaluating.
What wears fastest on a 16H doing mine haul-road work, and is it worth upgrading the wear inserts?
On haul-road and mine duty the circle takes the most abuse: circle teeth wear, the pinion mesh opens up, and the wear strips between the drawbar/circle and the support shoes (composite on later machines, bronze on older ones) wear down and need shimming or replacement. Field reports comparing OEM composite inserts against aftermarket poly slides are mixed - some operators see close to double the wear life, others see no real gain - so treat insert choice as an ongoing inspection item rather than a one-time fix. Cracks or weld repairs on the circle casting or A-frame are a bigger warning sign than insert wear itself, since they usually point back to a slip clutch that wasn't doing its job.
The 16H is throwing electrical fault codes - where do mechanics start?
Same discipline as any electronically controlled Cat machine of this era: read the MID/CID/FMI code off the display or diagnostic software before condemning a part. A voltage-above or voltage-below-normal code is just as often a chafed harness, a corroded connector, or a bad ground as an actual failed sensor - a simple wiggle test on the harness while watching the code will often surface an intermittent connection. On a 16H the harness routes across the articulation joint and around the tandem walkway, so that's the first place to check for chafing, corrosion or moisture on an older, higher-hour machine before chasing individual sensors.
How does the park brake and service brake system work on the 16H, and what fails?
Service brakes are air-over-hydraulic; the park brake is spring-applied and air-released, standard for this class of grader - with no air in the tanks the park brake spring sets automatically. Typical air system behavior on these machines: the compressor governor cuts in around 620 kPa (90 psi) and cuts out around 860-965 kPa (125-140 psi), the low-air warning buzzer comes on around 415-485 kPa (60-70 psi), and the park brake won't fully release until pressure climbs back to roughly 140-205 kPa (20-30 psi) - figures vary by configuration. If a machine is slow to release the park brake on startup, check for air system leaks and compressor cut-in/cut-out performance before assuming a bad brake chamber or valve. Brake work is safety-critical - have your dealer verify air system pressures and chamber condition before returning the machine to service.
What should I check before buying a used 16H?
Confirm which engine it actually has (3196 ETA versus the 3406 DITA in the ES variant) off the serial plate, since parts books diverge between them. With the engine running, turn the steering to full lock each direction and listen for a noisy cushion valve. Cycle the circle through its full range and watch for excess play in the pinion-to-tooth mesh, and inspect the circle casting and A-frame for cracks or weld repairs - both point to past overload from a slip clutch that wasn't slipping. Check the drawbar/circle wear strips and support shoes for wear and shimming history. Raise the front end at least 15 cm (6 in) and confirm both front wheels turn freely with no extra play in the radius arms or king pins, and check that the front and rear frame track straight - misalignment usually means a bent or worn articulation joint. Ask for service records showing the scheduled A/B/C interval service was followed, since this engine and hydraulic system are maintenance-sensitive. Pressure-test the hydraulics and inspect every cylinder, rod and pin for leaks or scoring. Given the safety and rebuild cost at stake, have your dealer verify hydraulic and brake system condition before you commit to purchase.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 16H part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.