Caterpillarmotor grader
Caterpillar 160H NA
Maintenance schedule, common problems & OEM parts breakdown
The Caterpillar 160H NA is a heavy motor grader in Cat's H-series lineup, built for road maintenance, fine grading, and heavy material moving. Two engine arrangements appear across its production run: an earlier fixed-rating Cat 3176C ATAAC (air-to-air aftercooled) inline-six rated 149 kW (200 hp) net at 2000 rpm, and a later Variable Horsepower (VHP) / VHP Plus 3176 ETA arrangement that steps output by gear, from 134 kW (180 hp) net in the low range up to roughly 149-164 kW (200-220 hp) net in the top gears. Standard operating weight runs 15,676-16,280 kg (34,560-35,890 lb) depending on tire and rim option, with gross machine weight reaching roughly 22,300-23,280 kg (49,165-51,325 lb) under full attachment allowance. The H-series family launched in the mid-1990s as the replacement for the earlier G-series graders, and the 160H NA sits at the top of the shared 12H/140H/160H mainframe and parts book, carrying larger tandem drive chains and cases than its 12H/140H siblings to handle the added horsepower. Power reaches the ground through an 8-speed forward, 6-speed reverse powershift transmission (roughly 3.8-43.6 km/h forward, 3.0-34.4 km/h reverse), articulated-frame steering with 20 degrees of articulation and 50 degrees of front-wheel steer, and joystick control of blade lift, circle drive, sideshift, tip, and centershift. A 4.27 m (14 ft) moldboard is standard, with a 4.88 m (16 ft) moldboard offered as an option. The NA designation marks the North America-spec electrical and engine-rating configuration, distinct from the Global-market 160H and the 160H ES trim.
The move from the fixed-rating 3176C ATAAC to the Variable Horsepower / VHP Plus 3176 ETA arrangement marks the real generational split inside the 160H NA nameplate. The VHP/VHP Plus engines meet or exceed U.S. EPA Tier II and EU Stage II emissions standards and add a power step across the gear range, while the earlier fixed-rating arrangement runs one flat output with no step and a slightly lower peak torque. Both arrangements share the same chassis, tandem, circle, and hydraulic hardware, so the practical difference for a buyer is engine calibration, emissions compliance, and top-gear output rather than machine size or capability. Caterpillar later replaced the H-series with the M-series 160M, which brought electronic hydraulic implement controls and a different engine platform. Because the 160H NA sold in volume to road departments, utilities, and general contractors across both engine arrangements, it remains one of the more common used graders on the market today. Parts commonality across the 12H/140H/160H family keeps circle, drawbar, tandem, and hydraulic components easy to source, and the mechanically straightforward 3176-family powertrain, electronically controlled but well understood by independent shops, makes the 160H NA a steady rebuild-and-resale candidate for buyers who want to avoid the added complexity of M-series electronics.
Below: full specifications, fluids & capacities, the factory service schedule, common service parts, verified fault codes, what owners discuss, attachment guidance, the complete assembly directory, and a serial-number reference. Complete parts lists with full OEM part numbers, exploded diagrams, quantities, and fitment data are available free in Heavy Parts AI.
Caterpillar 160H NA specifications
Engine
| Engine family | Cat 3176 turbocharged, air-to-air aftercooled six-cylinder diesel. Two factory arrangements appear across the 160H production run: an earlier fixed-rating 3176C ATAAC, and a later Variable Horsepower / Variable Horsepower Plus 3176 ETA. |
| Displacement / cylinders | 10.3 L (629 cu in), 6 cylinders. Bore 125 mm (4.9 in), stroke 140 mm (5.5 in). |
| Power - fixed-rating arrangement (3176C ATAAC) | 149 kW (200 hp) net at 2000 rpm, single power rating with no gear-based power step. |
| Power - VHP / VHP Plus arrangement (3176 ETA) | Base power all gears: 134 kW (180 hp) net / 147 kW (197 hp) gross. VHP: gears 1-3 134 kW (180 hp) net, gears 4-8 149 kW (200 hp) net. VHP Plus: gears 1-3 134 kW (180 hp), gears 4-6 149 kW (200 hp), gears 7-8 164 kW (220 hp) net (177 kW / 237 hp gross). |
| Max torque | 867 lb ft (1175 N·m) at 1000 rpm on the VHP/VHP Plus arrangement; approximately 841 lb ft (1140 N·m) at 1000 rpm on the fixed-rating arrangement. |
| Emissions tier | Meets or exceeds U.S. EPA Tier II and EU Stage II standards on the VHP/VHP Plus arrangement. |
Weights
| Standard operating weight | 15,676 kg (34,560 lb) in base configuration with 14.00-24 10PR tires, full fuel, coolant, lubricants and operator. Front axle 4,471 kg (9,856 lb), rear axle 11,206 kg (24,704 lb). Heavier tire/rim options push standard weight to roughly 16,280 kg (35,890 lb). |
| Maximum operating (gross vehicle) weight | 22,301 kg (49,165 lb) with full attachment allowance. Front axle 8,051 kg (17,749 lb), rear axle 14,250 kg (31,416 lb). Fully loaded configurations reach approximately 23,280 kg (51,325 lb) depending on options. |
| Ground pressure | Not published for this wheeled machine. |
Dimensions
| Overall length | 8.71 m (343 in), front tire to end of rear frame. Counterweight to ripper: 10.1 m (397.5 in). |
| Overall width | 2.48 m (97.6 in) outside front tires; 2.46 m (97 in) outside rear tires; 2.09 m (82.3 in) tire center lines. |
| Overall height | 3.13 m (123 in) low-profile cab; 3.36 m (132 in) high-profile cab; 3.10 m (122.2 in) canopy/no-cab. |
| Wheelbase | 6.17 m (243 in), front axle to mid-tandem. Tandem axle spacing 1.52 m (60 in). |
| Ground clearance | 625 mm (24.6 in) at front axle; 344 mm (13.5 in) at transmission case. |
| Standard moldboard width | 4.27 m (14 ft); a 4.88 m (16 ft) moldboard is offered as an option. |
Performance
| Travel speed - forward | 8 forward gears, 3.8-43.6 km/h (2.4-27.1 mph). |
| Travel speed - reverse | 6 reverse gears, 3.0-34.4 km/h (1.9-21.4 mph). |
| Turning radius | 7.5 m (24.6 ft), measured outside front tires. |
| Articulation / steering range | 20 degrees articulation, left/right. 50 degrees front-wheel steering, left/right. |
| Blade pull | 44,249 lb (20,071 kg) at max gross weight; 31,104 lb (14,109 kg) at base weight, figured at a 0.9 traction coefficient. |
| Max depth of cut | 770 mm (30.3 in). |
| Max lift above ground | 452 mm (17.8 in). |
Service capacities (summary)
| Fuel tank | 397 L (105 gal), ground-level fill. |
| Hydraulic system | 80 L (20.8 gal) total; 38 L (9.9 gal) in the reservoir tank. |
| Engine oil | 39 L (10.2 gal). |
| Cooling system | 38 L (10 gal). |
| Differential / final drives | 47 L (12.4 gal). |
| Tandem housing (each) | 64 L (16.9 gal). |
Values vary by configuration, region, and serial range — confirm against your machine before planning transport or lifts.
160H NA fluids & capacities
| System | Capacity | Recommended fluid |
|---|---|---|
| Engine crankcase (with filter) | approx. 39 L (10.2 US gal) per factory service-refill data for this machine; other 3176C-family literature cites a lower ~28 L (7.4 US gal) figure for different oil-pan applications — varies by configuration, verify against your machine's OMM oil-level chart | Cat diesel engine oil (Cat DEO) meeting Cat's diesel engine oil performance spec. Viscosity by climate: SAE 15W-40 above about -9°C (15°F); SAE 10W-30 for a wider cold range down to about -20°C (-4°F); full-synthetic 0W/5W-grade diesel oil for arctic starts below that. |
| Cooling system | 38 L (10.1 US gal) | Cat ELC (Extended Life Coolant), mixed 50/50 with clean water (or used pre-mixed); older-vintage factory fill for this era of machine was Cat conventional DEAC coolant maintained with Supplemental Coolant Additive (SCA) — do not mix conventional coolant with ELC. |
| Fuel tank | approx. 397 L (104.9 US gal); a close variant figure of 394 L (104 US gal) also appears in some specification listings — treat as approximate | No. 2-D diesel fuel (ultra-low-sulfur diesel); use No. 1-D or a winter-blend diesel in cold ambient below about 0°C (32°F) to prevent fuel waxing. |
| Differential and final drive (rear axle housing, combined) | 47 L (12.5 US gal) | Cat TDTO (Transmission/Drive Train Oil) meeting Cat's TO-4 drive-train oil spec. SAE 30 for normal ambient; SAE 10W for cold-start climates down to about -20°C (-4°F); Cat TDTO-TMS (multi-season synthetic blend) covers a wider range in one fill for machines with large seasonal swings. |
| Tandem final drive housings (each side) | 64 L (16.9 US gal) per side — two tandems fitted, one per side | Cat TDTO, same grade selection as the differential/final drive (SAE 30 normal ambient, SAE 10W cold-start, or TDTO-TMS multi-season). |
| Circle drive gearbox | 7 L (1.9 US gal) | Cat TDTO, drawn from the same drive-train oil circuit and viscosity grade as the differential and tandem final drives. |
| Hydraulic system (total, including tank, lines and cylinders) | 80 L (21.2 US gal) | Cat TDTO (shared power-train/hydraulic circuit oil on this machine) or Cat Hydraulic Oil (Cat HYDO Advanced) where the OMM specifies a dedicated hydraulic fill; viscosity graded by climate the same as the drive-train oil (SAE 10W for cold ambient, SAE 30 for normal/warm). |
| Hydraulic tank (refill capacity only) | 38 L (9.9 US gal) | Same fluid and viscosity grade as the hydraulic system entry above. |
| Front wheel spindle/bearing housings (each side, oil-bath sealed spindle) | approx. 0.5 L (0.13 US gal) per side | Cat TDTO drive-train oil, same grade as the differential and final drives; sealed "live spindle" design keeps the housing oil-bath lubricated and isolated from contaminants. |
| Grease (chassis, articulation hitch, drawbar ball-and-socket, circle rail, cylinder pins) | spec only — no fixed refill volume, apply per lubrication schedule | Cat Multipurpose Grease (NLGI 2) for general chassis fittings; Cat Prime Application Grease (moly-fortified, NLGI 2) recommended for heavily loaded pivot points such as the drawbar ball-and-socket, circle-drive rail and articulation hitch. |
Capacities are refill values from factory literature — always fill to the dipstick/sight gauge, not the number.
Caterpillar 160H NA maintenance schedule
| Service interval | Tasks |
|---|---|
| Every 50 h |
|
| Every 250 h |
|
| Every 500 h |
|
| Every 1,000 h |
|
| Every 2,000 h |
|
| Every 6,000 h |
|
Servicing the 160H NA beyond the schedule
Predictive Maintenance & Fluid Analysis
Run S.O.S oil sampling on the engine at every oil change; the ECM on both the fixed-rating 3176C ATAAC and VHP/VHP Plus 3176 ETA arrangements flags faults, not wear trends, so lab data is the early warning. Sample tandem, differential/final drive, and circle drive gearbox oil on the shared TDTO circuit at 500h to track drivetrain wear. Watch ELC coolant for corrosion-inhibitor depletion; a weak charge accelerates radiator and aftercooler pitting. Confirm which engine arrangement is fitted before setting valve lash or torque specs, since the two differ.
Corrective & Common Repairs
Drive circle shaft failures show up repeatedly on H-series graders; check the slip clutch shim pack first. Pull shims to free a binding circle, add shims if it slips under normal grading load. Circle teeth, circle shoes, and moldboard/drawbar wear strips wear as a set; replace them together to hold factory tightness rather than shimming one worn strip alone. Tandem housing seals and drive chain stretch are the other recurring wear points on the 160H's reinforced tandems. Inspect the front wheel spindle housing and circle drive gearbox for oil leaks.
Overhaul & Rebuild Points
On a 160H NA nearing overhaul, engine top-end wear (turbocharger cartridge, injector nozzles, cylinder liners and rings) shows up first, whichever engine arrangement is fitted, fixed-rating 3176C ATAAC or VHP/VHP Plus 3176 ETA. Pull an oil sample and check valve lash before committing to a full inline rebuild. On the chassis side, circle drive pinion and ring gear worn past shim allowance calls for a full circle replacement, not a patch. Tandem drive chains, housing bearings, and drawbar ball-and-socket wear are the next most common rebuild items on high-hour machines.
Seasonal & Environment Servicing
Cold-climate NA-spec 160H units need engine block heater use and Cat DEO switched to a cold-weather viscosity (10W-30, or synthetic for arctic starts) before winter; check that ELC coolant is not mixed with older conventional coolant. In hot, dusty road work, service primary and secondary air filters more often than the 250h book interval and keep the aftercooler fins clear to protect boost temperatures. Wash accumulated mud from tandem housings and circle/drawbar grease points before it packs into seals; re-grease immediately after washdown.
160H NA common service parts
| Part number | Part | Notes | |
|---|---|---|---|
| 1D-4540 | Bolt,Machine Fuel Filter Mounting | Fuel system service | Check fitment → |
| 1R-0750 | Filter As-Fuel | Fuel system service | Check fitment → |
| 6I-0273 | Filter Element As-Air | Air intake service | Check fitment → |
| 6I-0274 | Filter Element As-Air | Air intake service | Check fitment → |
| 231-4486 | Filter Element As-Cab Air | Air intake service | Check fitment → |
Always confirm against your machine's serial number — cross-check any part in Heavy Parts AI before ordering.
160H NA fault codes & troubleshooting
| Code | Meaning | Likely cause | What to do |
|---|---|---|---|
| CID 1-6, FMI 05 | Injector solenoid driver circuit for the flagged cylinder reads open or no current at the ECM driver return. | Brittle or cracked injector harness insulation at the valve cover, a corroded harness connector, or a failed injector solenoid winding. | Unplug and inspect the engine harness connector at the valve cover for corrosion, then check injector wiring under the valve cover for chafing or cracked insulation before replacing the injector. |
| CID 1-6, FMI 11 | ECM cannot identify a specific failure mode on the injector circuit; often logged across several cylinders at once rather than one. | Shared engine or injector harness fault (short, open, or corrosion) affecting a common high-side or low-side driver circuit rather than one bad injector. | Check the shared harness and connectors feeding the affected injector bank before condemning individual injectors; isolate one cylinder at a time to confirm. |
| CID 100, FMI 03/04 | Engine oil pressure sensor signal reads voltage above normal (03) or below normal (04) for the expected range. | Open or shorted sensor wiring, a failed oil pressure sensor, or a faulty sensor supply circuit. | Verify sensor supply voltage and ground, inspect the connector, then substitute the sensor if wiring checks out. |
| CID 110, FMI 03/04 | Engine coolant temperature sensor signal reads voltage above or below the expected range. | Corroded or damaged sensor connector, open or shorted signal wire, or a failed sensor element. | Check connector and wiring continuity to the ECM, confirm sensor resistance against spec, replace the sensor if out of range. |
| CID 102, FMI 03/04 | Boost (turbocharger outlet) pressure sensor signal reads outside the expected voltage range. | Sensor wiring fault, damaged sensor line, or sensor failure; can also follow a sensor supply voltage fault. | Inspect the sensor line for damage, check wiring and connector, verify sensor supply voltage before replacing the sensor. |
| CID 174, FMI 03/04 | Fuel temperature sensor signal reads above or below the expected voltage range. | Open or shorted sensor circuit, damaged connector, or a failed sensor. | Inspect wiring and connector, check sensor resistance against spec, replace the sensor if faulty. |
| CID 262/263, FMI 03/04 | 5V or 8V/12V sensor supply circuit reads outside its expected voltage, which can cause several sensor codes to log together. | Shorted sensor wiring pulling the supply down, a damaged sensor overloading the circuit, or an ECM supply driver fault. | Disconnect sensors fed by the affected supply one at a time to isolate the shorted branch before replacing the ECM. |
| CID 254, FMI 12 | ECM has logged an internal fault within its own control module. | Internal ECM hardware failure or a corrupted internal diagnostic. | Confirm the code with Cat ET, cycle key power to clear a transient fault, and replace or reflash the ECM if the code stays active. |
| CID 190, FMI 02 | Engine speed/timing signal is erratic, intermittent, or incorrect. | Damaged or loose speed/timing sensor, worn timing wheel, or a wiring fault. | Check sensor air gap and mounting, inspect wiring and connector, replace the sensor if the signal stays erratic. |
Codes and remedies are general guidance for this model family — always confirm with diagnostic tooling and your dealer before major repairs.
160H NA attachments & work tools
Front blade (push/dozer blade)
A hook-on front blade of roughly 2.7 m (9 ft) width mounts to the front lift group shared across the 140H/160H/140M/160M grader family. It needs the parallel front lift group (cylinder, hoses, mounting kit) plus an auxiliary hydraulic valve section to raise, lower, and tilt from the cab.
Front scarifier
A front scarifier hooks onto the same front lift group ahead of the moldboard. It is meant for light scarifying, breaking up compacted surface material before the moldboard passes, not heavy ripping duty.
Rear ripper/scarifier
A rear-mounted multi-shank ripper-scarifier bolts on behind the tandem drive so ripper weight loads over the rear tires for maximum penetration. Shanks come in ripper (aggressive penetration) and scarifier (light, surface-fracture) styles that mount on the same rear frame.
Moldboard and cutting edges
The 160H NA runs in the roughly 4.3 m (14 ft) moldboard class typical for mid-size Cat graders, around 686 mm (27 in) high. Cutting edges are offered curved or flat, serrated or non-serrated, with end bits and overlay plates to protect blade ends and the working edge.
Snow wing
An auxiliary side-mounted moldboard (snow wing) widens the cleared swath beyond the main blade. Mast-type wings are built to throw deep drifted snow, while mastless wings clear and bench shoulder drifts and can angle up to roughly 40 degrees.
Push block
A push block bolts to the front nose plate. It acts as a counterweight to offset a rear ripper and gives the grader a push point when assisting another machine or a plow unit.
Circle and drawbar
The circle/drawbar system uses a one-piece forged circle with replaceable wear inserts between drawbar, circle, and support shoes, plus a slip-clutch circle drive that protects the driveline if the moldboard hits an obstruction. A High Performance Circle upgrade is offered for extended service intervals on higher-use machines.
Grade control readiness
The 160H NA can take a factory- or dealer-installed grade-control attachment-ready package that pre-wires mounting points and harnessing for cross slope, sonic, laser, GPS, or universal total station blade-control upgrades, so a later grade-control install skips a full harness retrofit.
Work-tool hydraulics
Base grading hydraulics are load-sensing; adding a front lift group and a rear ripper together typically calls for extra valve sections or a hydraulic kit beyond the base grading circuit. Dealers match the hydraulic kit to whichever attachment combination is ordered, varies by configuration.
All 160H NA assemblies by section
Every catalogued assembly group for the Caterpillar 160H NA. Open an assembly to preview the parts inside — full OEM part numbers are available in Heavy Parts AI.
Air Inlet And Exhaust System
147-3088 Aftercooler Gp
| 11***77 | Regulator-Water Temperature; (86-Deg C To 97-Deg C) | 1 |
| 14***88 | Aftercooler Group | 1 |
| 7N***44 | Gasket; (Temperature Regulator Housing) | 1 |
111-7999 Aftercooler Gp-Air
| 03***19 | Bolt; --To Bearing Ret. At Lower Front Shaft Bore | 4 |
| 03***57 | Bolt; --To Reverse Shaft Bearing Retainer & Forward Shaft Bearing Retainer | 4 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
7e-5677 Air Cleaner Gp
| 03***19 | Bolt; --To Bearing Ret. At Lower Front Shaft Bore | 4 |
| 03***57 | Bolt; --To Reverse Shaft Bearing Retainer & Forward Shaft Bearing Retainer | 4 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 3 |
163-1850 Air Cleaner Gp
| 10***50 | Film; (Air Cleaner) (Radial Seal) (On Air Cleaner Cover) | 1 |
| 16***50 | Air Cleaner Group | 1 |
| 4P***24 | Seal-O-Ring | 1 |
106-7656 Air Cleaner Gp
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 10***56 | Air Cleaner Group | 1 |
| 10***57 | Tube As | 0 |
113-8513 Dust Ejector Gp
| 11***13 | Dust Ejector Group | 1 |
| 4P***24 | Seal-O-Ring | 1 |
| 6I***73 | Filter Element As-Air; (Primary) | 1 |
7e-5682 Fastener Gp-Exhaust Manifold
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
| 11***12 | Ejector As-Exhaust | 1 |
| 1B***55 | Nut,Plain,Hexagon Turbocharger Mounting | 1 |
106-7308 Lines Gp-Air
| 10***08 | Lines Group-Air | 1 |
| 10***58 | Hose | 1 |
| 14***67 | Clamp; (Hose) | 1 |
110-0020 Lines Gp-Air
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 1 |
| 10***92 | Tube-Air | 1 |
7c-2094 Lines Gp-Air
| 10***93 | Stud-Taperlock; (3/8-16x2.36-In)(3/8-16x60 Thd) | 1 |
| 1M***43 | Spacer; (10.5x25.4x18.21-mm Thk) | 1 |
| 2N***66 | Locknut; (3/8-16-Thd)(High Temperature) | 12 |
134-4208 Manifold Gp-Exhaust
| 13***08 | Manifold Group-Exhaust | 1 |
| 7N***86 | Manifold-Exhaust | 1 |
| 9Y***79 | Gasket Manifold Mtg Part Of Kit P/N 5r***26 | 3 |
6n-0164 Manifold Gp-Exhaust
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 1 |
| 10***92 | Tube-Air | 1 |
113-8511 Muffler & Mounting Gp
| 11***11 | Muffler & Mounting Group | 1 |
| 13***00 | Manifold-Exhaust | 1 |
| 8S***16 | Manifold-Exhaust; (Front) | 1 |
113-5340 Turbocharger Gp
| 10***07 | Turbocharger Group | 1 |
| 11***40 | Turbocharger Group | 1 |
| 1P***51 | Gasket; (Turbocharger) | 1 |
106-7407 Turbocharger Gp
| 10***07 | Turbocharger Group | 1 |
| 1B***55 | Nut,Plain,Hexagon Turbocharger Mounting | 2 |
| 26***57 | Muffler | 1 |
111-8035 Turbocharger Gp
| 11***35 | Turbocharger Group | 1 |
| 11***15 | Turbocharger Cartridge Group | 1 |
| 11***17 | Cover (Compressor) | 1 |
113-7919 Turbocharger Gp
| 11***19 | Turbocharger Group | 2 |
| 1P***51 | Gasket; (Turbocharger) | 1 |
| 2N***66 | Locknut; (3/8-16-Thd)(High Temperature) | 4 |
Basic Engine
3n-2886 Adapter Gp-Seal
| 0L***29 | Bolt- 7.63 cm(3 In.) Long - Location "H" | 1 |
| 2P***92 | Seal (Id=133.02mm) | 1 |
| 2W***62 | Retainer Assem. | 1 |
110-5764 Air Compressor Gp
| 11***64 | Air Compressor Group | 1 |
| 15***46 | Kit-Unloader; (Air Compressor) | 1 |
109-1317 Air Compressor Gp
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 5 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 14 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 1 |
111-7994 Air Compressor Gp
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 4 |
| 10***60 | Kit-Major Repair; (Air Compressor) | 1 |
| 10***22 | Cylinder Head As | 1 |
7w-8399 Air Compressor Gp
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 2 |
| 11***94 | Air Compressor Group | 1 |
| 1D***40 | Bolt,Machine Fuel Filter Mounting | 2 |
110-5765 Air Compressor Gp
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 2 |
| 10***17 | Air Compressor Group | 1 |
| 11***65 | Air Compressor Group | 1 |
1n-4406 Camshaft Gp
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 1N***06 | Camshaft Group-Single; Camshaft Group--Single | 1 |
| 4P***42 | Camshaft Group | 1 |
8n-3163 Cover Gp-Cylinder Block
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 2A***98 | Pin,Straight,Headle Flywheel Housing | 2 |
| 4B***38 | Plug 28.95 mm(1.14 In.) Hole Dia. | 1 |
2p-6530 Cover Gp-Cylinder Head
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 4 |
| 1P***67 | Cover,Access Cylinder Head | 1 |
| 2P***01 | Bolt Oil Filler Mounting; Used On Replacement Engine P/N 5r***83 | 4 |
2p-6529 Cover Gp-Front Housing
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 2 |
| 2P***29 | Cover Group-Front Housing; Front Housing Cover Group | 1 |
| 3S***13 | Nut-Full-Straps & Brackets | 6 |
8n-4745 Cover Gp-Valve Mechanism
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 15 |
| 2W***86 | Cover As-Cylinder Head | 1 |
| 8N***45 | Cover Group-Valve Mechanism; Valve Mechanism Cover Group | 1 |
120-4565 Crankshaft Gp
| 10***52 | Plate-Thrust | 2 |
| 12***64 | Crankshaft As | 1 |
| 12***65 | Crankshaft Group | 1 |
4p-9856 Crankshaft Gp
| 10***52 | Plate-Thrust | 2 |
| 19***34 | Kit-Basic Engine Repair; (Main Bearing)(Crankshaft) | 0 |
| 23***33 | Bearing-Main; (Standard)(Standard) | 7 |
7n-6550 Cylinder Block Gp
| 10***12 | Insert; (Liner Seat) (.822-mm Thk) | 6 |
| 10***18 | Insert; (Liner Seat) (1.605-mm Thk) | 6 |
| 10***27 | Insert-Liner Seat (2.710mm Thk) | 6 |
8n-5286 Cylinder Block Gp
| 11***50 | Gasket-Plate | 1 |
| 1S***40 | Dowel; (30.23 mm X 9.37 mm) | 1 |
| 2B***58 | Plug--To Block Upper Front Air Manifold | 3 |
1n-3576 Cylinder Block Gp
| 1N***76 | Cylinder Block Group | 1 |
| 1S***40 | Dowel; (30.23 mm X 9.37 mm) | 1 |
| 2S***58 | Washer-Hard; (17x29x3-mm Thk)(Engine Brake) | 14 |
7n-8876 Cylinder Head Gp
| 10***60 | Valve (Intake) | 6 |
| 10***65 | Insert-Valve Seat; (Exhaust)(Standard) | 6 |
| 10***68 | Insert-Valve Seat; (Inlet)(Standard) | 6 |
7e-6200 Damper Gp
| 5S***48 | Washer-Special | 1 |
| 6H***17 | Bolt,Machine Damper Use On Replacement Engine 5r***83 | 6 |
| 7B***63 | Screw,Cap,Hexagon Head Pulley Mtg | 1 |
7c-2091 Drive Gp-Fan
| 10***79 | Pulley; (3-Groove) | 1 |
| 15***52 | Support As | 1 |
| 16***59 | V-Belt Set; (Includes 3-Belts)(Fan Drive) | 1 |
7n-9536 Fastener Gp-Cylinder Head
| 1B***09 | Bolt-- Head To Cylinder Block | 5 |
| 1D***95 | Bolt (5/8-11x6in); (5/8-11x6-In) | 20 |
| 2S***36 | Washer,Flat Cover Assembly Mounting And Flywheel Housing Cover | 25 |
1w-3802 Fastener Gp-Front Housing
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 17 |
| 1C***51 | Bolt--Installation Of 2v***26 Retainer | 2 |
| 1W***02 | Fastener Group-Front Housing | 1 |
170-2496 Fastener Gp-Oil Pan
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 3 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 18 |
| 0T***73 | Bolt (3/8) (63.5mm Long) (On Cab Of Cover Assem.) | 5 |
2p-6200 Fastener Gp-Oil Pan
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 18 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 5 |
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 3 |
7e-5680 Flywheel Gp
| 0S***76 | Bolt 5.08 cm(2 In.) Long | 9 |
| 7E***80 | Flywheel Group | 1 |
| 7E***67 | Flywheel As | 1 |
111-8001 Gear Gp-Front
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 0S***48 | Bolt,Machine Camshaft Gear Mounting | 4 |
4p-9858 Gear Gp-Front
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 0S***48 | Bolt,Machine Camshaft Gear Mounting | 4 |
7e-5681 Housing Gp-Flywheel
| 7E***81 | Housing Group-Flywheel | 1 |
8n-0303 Housing Gp-Front
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 13 |
| 2A***62 | Gasket; (Rear Gear Housing Drain Plug) | 1 |
| 5F***04 | Plug-Drain; (5/8-18-2a Thd. Flywheel Housing) | 1 |
7n-9122 Lifting Gp-Engine
| 1W***00 | Gasket Timing Gear Cover | 1 |
| 1W***16 | Plate As-Front | 1 |
| 5M***14 | Pipe Plug Cylinder Block Oil Pressure | 1 |
128-0065 Lines Gp-Air Compressor
| 03***69 | Elbow-Flared; (1/2-14 Nptf) | 1 |
| 12***44 | Tube As | 1 |
| 12***65 | Lines Group-Air Compressor | 1 |
135-5094 Lines Gp-Air Compressor
| 03***69 | Elbow-Flared; (1/2-14 Nptf) | 1 |
| 13***94 | Lines Group-Air Compressor | 1 |
| 2N***87 | Elbow-Flared Needed For Customer; (Used Without Brakesaver) | 1 |
115-7540 Lines Gp-Air Compressor
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 4 |
| 11***40 | Lines Group-Air Compressor | 1 |
| 13***14 | Plate-Lifting | 1 |
7c-2096 Mounting Gp-Engine & Xmsn
| 03***72 | Elbow; (Flared 90 Degree) | 1 |
| 13***66 | Adapter | 1 |
| 14***39 | Hose As | 1 |
2p-9647 Pan Gp-Oil
| 1J***29 | Bolt-Plt; (1unc X 6) | 2 |
| 21***74 | Support; (Rh) | 1 |
| 21***75 | Support; (Lh) | 1 |
1w-6588 Piston & Rod Gp
| 11***36 | Adapter As-Drain | 1 |
| 1S***04 | Lug (Use As Required) | 1 |
| 1W***88 | Piston & Rod Group; Connecting Rod And Piston Group | 1 |
2p-6224 Seal Gp-Crankshaft
| 16***60 | Body As-Piston; (Requires 4mm Thick Oil Ring) | 1 |
| 1P***56 | Bolt,Shoulder Connecting Rod | 2 |
| 1S***43 | Ring,Retaining Piston Pin | 2 |
7c-3626 Support Gp-Engine
| 4W***52 | Seal Group-Crankshaft; (Counter Clockwise Rotation) | 1 |
| 7C***26 | Support Group-Engine | 1 |
| 9Y***95 | Seal Group-Crankshaft; (Clockwise Rotation) | 1 |
7c-7013 Valve Mechanism Gp
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 2 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 5 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 8 |
7n-8026 Valve Mechanism Gp
| 1B***09 | Bolt-- Head To Cylinder Block | 1 |
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
| 2S***36 | Washer,Flat Cover Assembly Mounting And Flywheel Housing Cover | 1 |
Braking System
8w-5750 Air Dryer Gp
| 1P***21 | Yoke | 1 |
| 20***57 | Seal | 1 |
| 20***58 | Seal | 1 |
9w-5132 Brake Gp-Parking
| 0S***66 | Bolt-Pulley To Crankshaft Adapter | 16 |
| 10***92 | Sprocket; (25-Teeth) | 4 |
| 14***10 | Spindle-Wheel | 4 |
8w-4265 Brake Gp-Service
| 11***34 | Hose As | 1 |
| 25***47 | Valve As-Air; (Parking Brake) | 1 |
| 3B***22 | Elbow (Use As Required) | 1 |
8w-5934 Control Gp-Parking Brake
| 11***26 | Plate As | 1 |
| 12***44 | Plate As | 1 |
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
8w-4741 Control Gp-Service Brake
| 11***26 | Plate As | 1 |
| 12***44 | Plate As | 1 |
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
8w-5547 Tank Gp-Air
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
185-0008 Valve Gp-Solenoid
| 18***08 | Valve Group-Solenoid; -Air Horn | 1 |
| 1F***48 | Nut 12.70 mm(.50 In.) Thread | 2 |
| 2M***79 | Stud-Taperlock; (3/8-16x0.177-In)(45mm) | 3 |
7t-9074 Valve Gp-Solenoid
| 15***70 | Nut; (1/2-20-2b-Thd) | 1 |
| 16***08 | Washer; (13.03x25.4x2.38-mm Thk) | 1 |
| 31***46 | Coil As | 1 |
Cooling System
147-3090 Lines Gp-Water
| 14***90 | Lines Group-Water | 1 |
| 2A***40 | Tube | 1 |
| 2A***41 | Hose | 1 |
4w-3124 Lines Gp-Water
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 2 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 1 |
8n-4408 Lines Gp-Water
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 2 |
8w-5829 Lines Gp-Water
| 7N***56 | Elbow-Bypass | 1 |
| 7X***31 | Plug-Pipe; (Flywheel Housing Drain) | 2 |
| 8T***65 | Plug-Pipe; (Diesel Particulate Filter) | 1 |
4w-6157 Lines Gp-Water
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 7 |
| 2A***41 | Gasket | 1 |
2w-7060 Lines Gp-Water
| 11***10 | Regulator-Water Temperature; (91 Deg Celsius) | 1 |
| 2W***60 | Lines Group-Water; Water Lines Group | 1 |
| 7H***71 | Plug,Pipe Base Assembly,Engine Oil Filter Assembly | 1 |
2w-7279 Cooler Gp-Fltr Base & Eng Oil
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 1 |
| 1P***46 | Washer-Hard; (10.2x35x6-mm Thk) | 1 |
| 2W***79 | Cooler Group-Filter Base & Eng Oil; Cooler Gp-Filter Base & Engine Oil | 1 |
2w-7280 Cooler Gp-Fltr Base & Eng Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 3 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 3 |
147-0362 Cooler Gp-Fltr Base & Eng Oil
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 3 |
| 14***62 | Cooler Group-Filter Base & Eng Oil | 1 |
147-0364 Cooler Gp-Fltr Base & Eng Oil
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 14***64 | Cooler Group-Filter Base & Eng Oil | 2 |
| 2W***61 | Gasket | 1 |
147-0360 Cooler Gp-Fltr Base & Eng Oil
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 14***60 | Cooler Group-Filter Base & Eng Oil | 2 |
4w-6163 Cooler Gp-Fltr Base & Eng Oil
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 1R***39 | Filter As-Engine Oil; (Standard Efficiency) | 1 |
| 2W***61 | Gasket | 1 |
4w-6162 Cooler Gp-Fltr Base & Eng Oil
| 0L***52 | Capscrew (3/8 - 16 Nc X 3 1/4 Gd8, Hex) | 1 |
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
147-0359 Cooler Gp-Fltr Base & Eng Oil
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 14***59 | Cooler Group-Filter Base & Eng Oil | 1 |
140-9810 Cover Gp-Fan
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 2 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 2 |
| 14***10 | Cover Group-Fan | 1 |
8w-5794 Extension Gp-Drain
| 12***06 | Stud | 12 |
| 14***57 | Cover-Fan | 1 |
| 8W***94 | Extension Group-Drain; -Radiator | 1 |
7c-2095 Fan Gp-Blower -Radiator
| 00***14 | Coupling-Pipe | 1 |
| 00***34 | Elbow-Pipe | 1 |
| 1P***97 | Valve-Drain; (Radiator) | 1 |
8n-0888 Regulator Gp-Temperature
| 13***77 | Bracket | 2 |
| 16***61 | Radiator Group | 1 |
| 17***05 | Plate As | 2 |
2y-9679 Housing & Regulator Gp
| 19***49 | Fan; (8-Blade) | 1 |
| 2Y***79 | Housing & Regulator Group | 1 |
| 8T***21 | Washer-Hard; (11x21x2.5-mm Thk)(M10x1.50x30mm) | 8 |
106-3927 Pump Gp-Water
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 10***27 | Pump Group-Water | 1 |
106-3926 Pump Gp-Water
| 10***26 | Pump Group-Water | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
| 1A***79 | Capscrew (5/16 - 18 Nc X 1 1/2 Gd5, Hex) | 7 |
7c-2099 Radiator Gp
| 13***77 | Bracket | 2 |
| 18***80 | Radiator Group | 1 |
| 1F***50 | Nut Rops Support | 2 |
7e-5679 Radiator Gp
| 13***77 | Bracket | 2 |
| 2A***04 | Plate As | 2 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 4 |
7c-2098 Radiator Gp
| 13***77 | Bracket | 2 |
| 2A***04 | Plate As | 2 |
| 4B***74 | Washer (Required Only When Bosch Alternator Is Fitted) | 7 |
151-0996 Regulator Gp-Temperature
| 11***10 | Regulator-Water Temperature; (91 Deg Celsius) | 1 |
| 15***96 | Regulator Group-Temperature | 1 |
| 7N***44 | Gasket; (Temperature Regulator Housing) | 1 |
Electrical And Starting System
9x-7164 Lamp Gp-Head
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
| 9X***63 | Lamp-Halogen; (24-Volt, 70-Watt)(Floodlight) | 1 |
168-1960 Lamp Gp-Head
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***49 | Lens As; (Headlight, High Beam) | 1 |
| 15***51 | Clamp | 2 |
133-3037 Lamp Gp-Head
| 13***37 | Lamp Group-Head | 1 |
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
9x-7169 Lamp Gp-Head -Low Beam
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
| 9X***63 | Lamp-Halogen; (24-Volt, 70-Watt)(Floodlight) | 1 |
171-2066 Lamp Gp-Head
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***51 | Clamp | 2 |
| 15***52 | Bezel | 1 |
9x-6874 Lamp Gp-Head
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
| 9X***63 | Lamp-Halogen; (24-Volt, 70-Watt)(Floodlight) | 1 |
133-3035 Lamp Gp-Head
| 13***35 | Lamp Group-Head; -High Beam | 1 |
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
9x-7170 Lamp Gp-Head -High Beam
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
| 9X***63 | Lamp-Halogen; (24-Volt, 70-Watt)(Floodlight) | 1 |
9g-9813 Alarm Gp
| 1P***52 | Insulator,Bushing Governor | 1 |
| 2P***85 | Spacer (.635 mm Thk); (0.635-mm Thk) | 1 |
| 2W***34 | Bar-Load Stop; (4.0mm Thk) | 1 |
123-6449 Alarm Gp
| 12***49 | Alarm Group | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
112-4320 Alternator Ar-Charging
| 10***47 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 11***20 | Alternator Ar-Charging | 1 |
112-4322 Alternator Ar-Charging
| 11***22 | Alternator Ar-Charging | 1 |
| 3E***77 | Alternator Group-Charging | 1 |
| 9S***93 | Circuit Breaker As; (80-Ampere) | 1 |
8x-8046 Alternator Ar-Charging
| 3E***77 | Alternator Group-Charging | 1 |
| 8X***46 | Alternator Ar-Charging | 1 |
150-7668 Alternator Ar-Charging
| 15***68 | Alternator Ar-Charging | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 2 |
| 3E***94 | Circuit Breaker As; (105-Ampere)(Alternator) | 1 |
150-7669 Alternator Ar-Charging
| 0S***70 | Cap Screw (5/8" Long) | 2 |
| 15***69 | Alternator Ar-Charging | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 2 |
6n-9294 Alternator Gp-Charging
| 3T***52 | Alternator Group-Charging | 1 |
| 6N***94 | Alternator Group; (24-Volt, 35-Ampere) | 1 |
| 7N***20 | Alternator Group; Alternator Group (Robert Bosch) | 1 |
7n-9720 Alternator Gp-Charging
| 1B***05 | Key; (Woodruff) | 1 |
| 1L***48 | Nut-Plated Jam; (7/16-14-Thd) | 1 |
| 2K***21 | Locknut (5/8-18 Thd) | 1 |
7c-1905 Alternator Gp-Charging
| 12***94 | Strap-Belt Adjustment | 1 |
| 5P***76 | Washer Guard To Support Assembly And Guard Assembly | 1 |
| 6N***94 | Alternator Group; (24-Volt, 35-Ampere) | 1 |
100-5047 Alternator Gp-Charging
| 10***45 | Alternator Group-Charging; (Nippondenso) | 1 |
| 10***46 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 10***47 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
100-5046 Alternator Gp-Charging
| 10***46 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 2K***21 | Locknut (5/8-18 Thd) | 1 |
100-5045 Alternator Gp-Charging
| 10***45 | Alternator Group-Charging; (Nippondenso) | 1 |
| 1B***05 | Key; (Woodruff) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
9x-7803 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 4 |
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
9g-4574 Alternator Gp-Charging
| 1B***05 | Key; (Woodruff) | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
| 2H***20 | Lockwasher (11.38mm Id) | 1 |
114-2401 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 4 |
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
3t-6352 Alternator Gp-Charging
| 03***12 | Screw-Forming; (10-24x0.5-In) | 5 |
| 11***19 | Diode As-Alternator | 1 |
| 1H***44 | Lockwasher (Bracket To Cab) | 1 |
3e-7577 Alternator Gp-Charging
| 10***31 | Fan-Alternator; (11-Blade) | 1 |
| 10***32 | Collar; (Alternator) | 1 |
| 10***56 | Diode As; (Alternator) | 1 |
152-5584 Alternator Gp-Charging
| 10***47 | Alternator Group-Charging; -24-Volt, 50-Ampere | 1 |
| 15***84 | Alternator Group-Charging | 1 |
| 1F***48 | Nut 12.70 mm(.50 In.) Thread | 1 |
151-5611 Battery & Wiring Gp
| 11***57 | Cable As | 1 |
| 15***11 | Battery & Wiring Group; -Heavy-Duty | 1 |
| 15***10 | Battery; (12-Volt, 1400-Cca) | 2 |
134-6553 Control Gp-Power Train
| 13***53 | Control Group-Power Train | 1 |
143-9634 Control Gp-Power Train
| 14***34 | Control Group-Power Train | 1 |
154-6527 Control Gp-Power Train
| 15***27 | Control Group-Power Train | 1 |
142-3363 Control Gp-Unprogrammed
| 10***52 | Screw-Pan Head; (8-32x0.375-In) | 1 |
| 14***63 | Control Group-Unprogrammed; -Electronic Hydrostatic Control | 1 |
| 6V***03 | Kit; (Retaining Bolt) (Each Includes Bolt, Retaining Ring And 4 O-Ring Seals) | 2 |
132-2148 Control Gp-Unprogrammed
| 10***52 | Screw-Pan Head; (8-32x0.375-In) | 1 |
| 13***48 | Control Group-Unprogrammed; -Power Train | 1 |
| 6V***03 | Kit; (Retaining Bolt) (Each Includes Bolt, Retaining Ring And 4 O-Ring Seals) | 2 |
172-9389 Control Gp-Unprogrammed
| 10***52 | Screw-Pan Head; (8-32x0.375-In) | 1 |
| 13***26 | Washer; (4.52x8.28x0.76-mm Thk) | 1 |
| 17***89 | Control Group-Unprogrammed; -Steering, Transmission | 1 |
145-1279 Converter Ar-Electrical -High
| 14***47 | Accessory Group-Cab; -High | 1 |
| 14***61 | Converter Group-Electrical | 1 |
| 14***79 | Converter Ar-Electrical; -High | 1 |
145-1278 Converter Ar-Electrical -Low
| 14***42 | Accessory Group-Cab; -Low | 1 |
| 14***61 | Converter Group-Electrical | 1 |
| 14***78 | Converter Ar-Electrical; -Low | 1 |
145-1261 Converter Gp-Electrical
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 14***61 | Converter Group-Electrical | 1 |
| 20***85 | Converter Group-Electrical; (24-Volt To 12-Volt)(Air Conditioner, Heater) | 1 |
2a-7346 Converter Gp-Electrical
| 11***33 | Converter-Power; (24-Volt To 12-Volt) | 1 |
| 2A***46 | Converter Group-Electrical | 1 |
| 4L***54 | Capscrew; (3/8-16x21 In) (Gd8) (Hex Hd) (4-Roller) | 2 |
145-1297 Converter Gp-Electrical
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 2 |
| 14***97 | Converter Group-Electrical; -Radio | 1 |
| 20***85 | Converter Group-Electrical; (24-Volt To 12-Volt)(Air Conditioner, Heater) | 1 |
112-0830 Converter Gp-Electrical
| 10***56 | Plate | 1 |
| 11***29 | Harness As-Radio | 1 |
| 11***30 | Converter Group-Electrical | 1 |
144-8622 Electronics Gp-Power Train
| 14***22 | Electronics Group-Power Train | 1 |
| 17***89 | Control Group-Unprogrammed; -Steering, Transmission | 1 |
| 25***84 | Software Group-Power Train | 2 |
4n-3586 Heater Gp-Jacket Water
| 4N***86 | Heater Group-Jacket Water; (120v) | 1 |
| 6N***04 | Cap As-Dust; (Jacket Water Heater Elements) | 1 |
| 9G***57 | Element As-Jacket Water Heater; (120-Volt, 1250-Watt) | 1 |
8c-9678 Lamp Gp-Dome
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***82 | Housing (Plug) (To Lift Kickout Switch) | 1 |
9x-6775 Lamp Gp-Flood -Front, Rear
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***55 | Body As-Lamp | 1 |
| 9X***63 | Lamp-Halogen; (24-Volt, 70-Watt)(Floodlight) | 1 |
9x-1439 Lamp Gp-Flood -Vertical
| 8T***37 | Screw; (Machine) (M4x0.7x12mm) | 2 |
| 9X***39 | Lamp Group-Flood; -Rear-Ladder Access-Engine Work Light | 1 |
| 9X***55 | Body As-Lamp | 1 |
162-3294 Lamp Gp-Flood
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 15***48 | Lens As; (Floodlight) | 1 |
| 15***52 | Bezel | 1 |
8c-6207 Lamp Gp-Stop & Tail -Stop, Tail
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***82 | Housing (Plug) (To Lift Kickout Switch) | 1 |
7x-6066 Lamp Gp-Signal
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
| 7N***37 | Housing-To Air Start Solenoid Valve | 1 |
130-3452 Lamp Gp-Stop & Tail
| 13***52 | Lamp Group-Stop & Tail | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 1 |
128-6983 Lamp Gp-Warning Beacon -Rotating, Amber
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 12***83 | Lamp Group-Warning Beacon; -Rotating, Amber | 1 |
| 18***35 | Pin-Connector; (16-Ga To 18-Ga) | 2 |
8w-7663 Lighting Ar-Flood
| 10***21 | Lighting Group-Flood | 1 |
| 10***22 | Lighting Group-Flood | 1 |
| 8W***63 | Lighting Ar-Flood | 1 |
8w-7660 Lighting Ar-Flood & Signal
| 10***21 | Lighting Group-Flood | 1 |
| 10***23 | Lighting Group-Signal | 1 |
| 8W***60 | Lighting Ar-Flood & Signal | 1 |
160-7734 Lighting Gp-Backup
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
| 10***35 | Lamp Kit | 1 |
| 12***97 | Panel | 1 |
105-2222 Lighting Gp-Flood
| 10***94 | Harness As-Front Lighting | 1 |
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***22 | Lighting Group-Flood | 1 |
151-5924 Lighting Gp-Flood
| 12***97 | Panel | 1 |
| 12***22 | Bracket As | 1 |
| 12***23 | Wire As | 1 |
105-2221 Lighting Gp-Flood
| 10***57 | Bracket Assem. | 4 |
| 10***21 | Lighting Group-Flood | 1 |
| 3P***54 | Grommet | 2 |
125-6783 Lighting Gp-Flood
| 10***57 | Bracket Assem. | 2 |
| 12***83 | Lighting Group-Flood | 1 |
| 13***37 | Lamp Group-Head | 2 |
8w-7662 Lighting Gp-Flood -Front, Rear
| 10***90 | Harness As-Front Lighting; (Blade) | 2 |
| 10***92 | Harness As-Rear Lighting; (Floodlights) | 2 |
| 10***93 | Harness As-Rear Lighting | 1 |
105-2223 Lighting Gp-Signal
| 10***78 | Switch As-Rotary; (Headlights-High/Low) | 1 |
| 10***23 | Lighting Group-Signal | 1 |
| 10***58 | Flasher As; (24-Volt) | 1 |
7i-5011 Lighting Gp-Warning Beacon
| 10***62 | Switch As; (Warning Beacon) | 1 |
| 10***32 | Plate As | 1 |
| 11***18 | Clip | 1 |
170-5335 Motor Gp-Electric -Circulating Fan
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***35 | Motor Group-Electric; -Circulating Fan | 1 |
| 9W***52 | Pin-Connector; (14-Ga To 16-Ga) | 2 |
189-5746 Sensor Gp-Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***36 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
| 17***49 | Strap; (Marker) | 1 |
3e-7886 Sensor Gp-Speed
| 17***49 | Strap; (Marker) | 1 |
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 1 |
7w-3355 Sensor Gp-Speed
| 3E***86 | Sensor Group-Speed; -Magnetic, Low Output | 1 |
| 4B***81 | Washer--Use With Customer'S Ground Bolt | 1 |
| 7W***55 | Sensor Group-Speed; -Engine Timing | 1 |
183-8597 Sensor Gp-Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 17***49 | Strap; (Marker) | 1 |
| 18***97 | Sensor Group-Speed; -Transmission Output | 1 |
105-5152 Sensor Gp-Speed
| 10***87 | Sensor Group-Speed; (Transmission Output) | 1 |
| 10***52 | Sensor Group-Speed | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 1 |
3e-8700 Sensor Gp-Temperature
| 10***08 | Kit; (Connecting Plug) (3 Pin) (Includes Plug As And Wedge) | 1 |
| 10***13 | Seal; (3 Pin Plug) | 1 |
| 3E***68 | Wedge-Plug Lock; (3-Pin) | 1 |
145-5172 Service Gp-Power Train
| 14***72 | Service Group-Power Train | 1 |
| 17***89 | Control Group-Unprogrammed; -Steering, Transmission | 1 |
| 22***03 | Software Group-Power Train | 2 |
6i-3792 Solenoid Gp-Control
| 03***44 | Seal-O-Ring | 1 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0S***17 | Bolt --Use Open Hole In Compressor Body | 3 |
6i-2108 Solenoid Gp-Shutoff
| 2A***46 | Bolt,Machine Governor Linkage Bracket | 2 |
| 3E***85 | Solenoid Assem. | 1 |
| 4B***74 | Washer (Required Only When Bosch Alternator Is Fitted) | 1 |
108-6496 Starting Aid Gp-Ether
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***96 | Starting Aid Group-Ether | 1 |
| 11***39 | Tube | 1 |
8w-4619 Starting Aid Gp-Ether
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 14***35 | Tube | 1 |
| 3E***65 | Wedge; (Receptacle Lock) (2 Pin) | 1 |
207-1560 Starting Motor Gp-Electric
| 20***60 | Starting Motor Group-Electric | 1 |
| 20***61 | Starting Motor Group-Electric | 1 |
| 6V***38 | Starting Motor Group-Electric | 1 |
6v-5538 Starting Motor Gp-Electric
| 3E***25 | Cover As; (Starting Motor) | 1 |
| 3E***27 | Kit-Bearing; (Starting Motor)(Incl Bearing Seals & Spacers) | 1 |
| 3E***28 | Kit; (Brush) (Includes O-Rings, Screw, Spring, & Brush) | 1 |
207-1554 Starting Motor Gp-Electric
| 20***54 | Starting Motor Group-Electric | 1 |
| 20***55 | Starting Motor Group-Electric; (Delco Remy) | 1 |
| 6V***26 | Starting Motor Group-Electric | 1 |
6v-5207 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 2H***29 | Ring - Retaining External | 1 |
106-8552 Starting Motor Gp-Electric
| 10***52 | Starting Motor Group-Electric | 1 |
| 5C***74 | Nut (M5x.8 Thd); (M5x0.8-Thd) | 2 |
| 7X***62 | Washer-Hard; (13.5x19x0.8-mm Thk) | 5 |
207-1561 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 20***61 | Starting Motor Group-Electric | 1 |
| 25***79 | Kit-Solenoid; (24-Volt)(Starting Motor) | 1 |
6v-5226 Starting Motor Gp-Electric
| 3E***25 | Cover As; (Starting Motor) | 1 |
| 3E***27 | Kit-Bearing; (Starting Motor)(Incl Bearing Seals & Spacers) | 1 |
| 3E***28 | Kit; (Brush) (Includes O-Rings, Screw, Spring, & Brush) | 1 |
6v-5537 Starting Motor Gp-Electric
| 03***21 | Shim Lever Housing | 1 |
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 2H***29 | Ring - Retaining External | 1 |
1w-3851 Starting Motor Gp-Electric
| 10***55 | Starting Motor Group-Electric | 1 |
| 1W***51 | Starting Motor Group-Electric | 1 |
| 4H***69 | Gasket Starter Mtg Part Of Kit P/N 5r***25 | 1 |
106-8555 Starting Motor Gp-Electric
| 10***55 | Starting Motor Group-Electric | 1 |
| 6V***23 | Starting Motor Group-Electric | 1 |
| 6V***07 | Starting Motor Group-Electric | 1 |
6v-5023 Starting Motor Gp-Electric
| 5C***74 | Nut (M5x.8 Thd); (M5x0.8-Thd) | 2 |
| 6V***23 | Starting Motor Group-Electric | 1 |
| 7X***62 | Washer-Hard; (13.5x19x0.8-mm Thk) | 5 |
6v-5227 Starting Motor Gp-Electric
| 10***52 | Starting Motor Group-Electric | 1 |
| 6V***27 | Starting Motor Group-Electric | 1 |
| 6V***37 | Starting Motor Group-Electric | 1 |
207-1555 Starting Motor Gp-Electric
| 03***23 | Bolt; (1/4-28x1-In) | 5 |
| 19***70 | Solenoid As-Starting Motor; (24-Volt)(Starting Motor) | 1 |
| 20***55 | Starting Motor Group-Electric; (Delco Remy) | 1 |
105-8827 Suppressor Gp-Electronic
| 10***27 | Suppressor Group-Electronic; -Air Conditioner Compressor | 1 |
| 7N***79 | Socket-Governor Solenoid Wire To Housing | 2 |
| 7N***80 | Pin-Connector; (14-Ga To 18-Ga) | 2 |
7n-0718 Switch Gp-Disconnect -Battery
| 2H***22 | Lockwasher | 2 |
| 6F***45 | Nut-Full; (3/8-24-Thd) | 2 |
| 7N***18 | Switch As-Disconnect; -Battery-Ground Level | 1 |
167-0138 Switch Gp-Magnetic
| 15***61 | Wedge-Plug Lock; (2-Pin) | 1 |
| 15***70 | Kit-Connecting Plug; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 16***38 | Switch Group-Magnetic; -Main Relay-Main Power Relay | 1 |
9g-7641 Switch Gp-Start -Engine, Key
| 6V***24 | Lock As-Cylinder | 1 |
| 6V***62 | Screw-Machine; (8-32x0.31-In) | 4 |
| 7T***99 | Nut-Mounting; (1-32-Thd) | 1 |
2a-6469 Wiring Gp-Blade Cushion
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***88 | Harness As-Chassis; (Blade Cushion) | 1 |
| 2A***69 | Wiring Group-Blade Cushion | 1 |
151-6925 Wiring Gp-Cab
| 10***62 | Switch As; (Warning Beacon) | 1 |
| 10***32 | Plate As | 1 |
| 11***18 | Clip | 1 |
8w-7455 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 3 |
| 10***61 | Harness As-Cab; (Rear)(Rear Cab) | 1 |
| 10***81 | Harness As-Panel; (Cab Fuse Panel) | 1 |
130-0160 Wiring Gp-Cab
| 09***66 | Washer; (Hard) (4.5x9x1mm Thk) | 3 |
| 12***47 | Plate | 1 |
| 13***60 | Wiring Group-Cab | 1 |
8x-7707 Wiring Gp-Console
| 10***90 | Plate | 1 |
| 11***64 | Control Group-Relay | 1 |
| 12***33 | Harness As | 1 |
8x-7706 Wiring Gp-Engine
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 10***87 | Plate | 1 |
| 11***31 | Film; (Identification) (On Fuse Box Near Diagnostick Connector) | 1 |
8x-7709 Wiring Gp-Front
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***05 | Kit-Receptacle; (6-Pin)(Display Monitor Harness) | 2 |
| 11***64 | Control Group-Relay | 1 |
8x-7711 Wiring Gp-Rear
| 06***61 | Cable As; (Negative) | 1 |
| 10***40 | Switch As-Magnetic; (Main Power Relay) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
112-1106 Wiring Gp-Shutoff
| 11***06 | Wiring Group-Shutoff | 1 |
| 11***47 | Harness As | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 3 |
8x-7708 Wiring Gp-Steering Console
| 10***97 | Harness As-Front Lighting | 1 |
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***04 | Kit-Receptacle; (4-Pin)(Start Switch) | 1 |
Engine Arrangement
146-4339 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
| 11***20 | Lines Group-Air | 1 |
146-4344 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***08 | Lines Group-Air | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
111-8005 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
| 11***20 | Lines Group-Air | 1 |
110-1609 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***08 | Lines Group-Air | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
119-0279 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***08 | Lines Group-Air | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
119-0278 Engine Ar
| 10***27 | Pump Group-Water | 1 |
| 10***57 | Pump Group-Engine Oil | 1 |
| 11***20 | Lines Group-Air | 1 |
123-4195 Installation Ar-Engine
| 11***11 | Muffler & Mounting Group | 1 |
| 11***13 | Dust Ejector Group | 1 |
| 12***95 | Installation Ar-Engine | 1 |
124-2447 Installation Ar-Engine
| 11***11 | Muffler & Mounting Group | 1 |
| 11***13 | Dust Ejector Group | 1 |
| 12***47 | Installation Ar-Engine | 1 |
Frame And Body
101-8075 Axle Gp-Front
| 03***60 | Cup-Roller Bearing | 2 |
| 03***61 | Cone-Roller Bearing | 2 |
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 1 |
134-1080 Axle Gp-Front
| 03***44 | Rivet (For Outside Japan); Rivet (For Outside Japan) | 6 |
| 13***80 | Axle Group-Front | 1 |
| 13***25 | Support As-Lh | 1 |
8x-5330 Box Gp-Battery
| 7I***83 | Bumper As | 1 |
| 7X***01 | Bolt; (1-8x1.75-In) | 8 |
| 8T***61 | Washer-Hard-49mm Od X 28mm Id X 5mm Thk | 8 |
7i-5116 Bumper Gp-Rear
| 2A***98 | Gasket | 1 |
| 2D***38 | Stud-Taperlock; (5/8-11x2.5-In) | 12 |
| 2R***00 | Stud-Taperlock | 38 |
8w-5470 Case & Frame Gp
| 12***03 | Cover-Door | 2 |
| 12***04 | Cover-Radiator | 1 |
| 12***05 | Cover-Muffler | 1 |
113-9813 Cover Gp-Protection
| 11***92 | Plate | 2 |
| 11***36 | Cover | 1 |
| 11***57 | Rod | 2 |
7i-4942 Enclosure Gp-Engine
| 11***36 | Cover | 1 |
| 11***57 | Rod | 2 |
| 11***17 | Handrail | 2 |
141-2995 Frame Gp-Front
| 10***96 | Grill As-Radiator | 1 |
| 10***56 | Support As | 1 |
| 11***17 | Handrail | 2 |
8w-6248 Frame Gp-Front
| 11***45 | Plate | 2 |
| 14***94 | Frame As | 1 |
| 14***61 | Plate | 1 |
8w-5385 Guard & Support Gp-Radiator
| 10***96 | Grill As-Radiator | 1 |
| 11***17 | Handrail | 2 |
| 12***27 | Seal; (95-cm Each) | 0 |
140-7616 Guard & Support Gp-Radiator
| 11***26 | Plate | 2 |
| 11***27 | Plate | 2 |
| 11***35 | Tandem As-Rh | 1 |
111-4924 Guard Gp-Brake Lines
| 10***17 | Shield | 1 |
| 10***19 | Shield As | 1 |
| 11***24 | Guard Group-Brake Lines | 1 |
8w-5870 Guard Gp-Drive Shaft
| 10***20 | Clip | 4 |
| 12***49 | Floor Mat | 1 |
| 16***82 | Grommet | 1 |
7i-5045 Guard Gp-Platform
| 10***20 | Clip | 8 |
| 13***94 | Pipe As | 1 |
| 16***82 | Grommet | 1 |
8x-4154 Guard Gp-Platform
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 6 |
| 0S***87 | Bolt-Bracket Assembly To Timing Gear | 2 |
| 0S***89 | Bolt, Hex. Hd., 5/8"-11 N.C. X 1 3/4" | 4 |
106-4884 Hitch Gp-Articulating
| 10***84 | Hitch Group-Articulating | 1 |
| 3B***69 | Elbow-Adapter To Fitting | 2 |
| 3B***33 | Fitting; (Nipple-Pipe) | 1 |
262-1430 Lines Gp-Lubrication
| 13***37 | Tie Rod Group; (Rh Thread, Lh)(Rh Thread)(Left Side) | 1 |
| 13***38 | Tie Rod Group; (Lh Thread, Rh)(Lh Thread)(Right Side) | 1 |
| 13***39 | Tie Rod | 1 |
7i-4610 Lines Gp-Lubrication
| 22***74 | Enclosure As | 1 |
| 23***64 | Hose As | 1 |
| 23***65 | Block | 1 |
234-8936 Lines Gp-Lubrication
| 23***64 | Hose As | 1 |
| 23***65 | Block | 1 |
| 23***36 | Lines Group-Lubrication | 1 |
7d-8912 Link Gp-Steering
| 10***50 | Film; (Air Cleaner) (Radial Seal) (On Air Cleaner Cover) | 1 |
| 14***10 | Cover Group-Fan | 1 |
| 14***02 | Cover As-Air Cleaner | 1 |
140-9808 Protection Ar-Snow Plow
| 11***24 | Guard Group-Brake Lines | 1 |
| 12***59 | Plate | 1 |
| 14***08 | Protection Ar-Snow Plow | 1 |
140-9813 Protection Ar-Snow Plow
| 12***98 | Plate; (Rh) | 2 |
| 12***99 | Plate; (Lh) | 2 |
| 14***13 | Protection Ar-Snow Plow | 1 |
8x-1030 Step Gp
| 10***19 | Door As | 1 |
| 14***87 | Hose As | 1 |
| 15***45 | Kit-Mounting | 1 |
Fuel System
7c-8993 Fastener Gp-Fuel Inj Pump
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 2 |
| 4M***03 | Packing,Preformed Hourmeter Mtg | 1 |
| 4W***29 | Cover | 1 |
1w-3597 Torque Control Gp
| 14***60 | Tank As-Fuel | 1 |
| 15***49 | Sender As-Fuel Level | 1 |
| 15***52 | Kit-Dial Sensor; (Includes Sensor As & Screws) | 1 |
112-7491 Control Ar-Governor
| 11***09 | Engine Ar | 1 |
| 11***06 | Wiring Group-Shutoff | 1 |
| 11***91 | Control Ar-Governor | 1 |
112-1781 Control Ar-Governor
| 11***81 | Control Ar-Governor | 1 |
| 11***15 | Turbocharger Cartridge Group | 1 |
| 11***16 | Housing (Turbine) | 1 |
111-5162 Control Gp-Fuel Ratio
| 11***62 | Control Group-Fuel Ratio (Basic) | 1 |
| 11***78 | Engine Ar | 1 |
8w-4742 Control Gp-Governor
| 00***08 | Setscrew-Socket; (3/8-16x0.5-In) | 1 |
| 0V***96 | Bolt 1.125 In. (2.86 cm) Long | 2 |
| 11***64 | Boot | 3 |
1w-2481 Cover Gp-Tachometer Drive
| 00***08 | Setscrew-Socket; (3/8-16x0.5-In) | 1 |
| 03***48 | Clip; (11.11mm .437in Id) | 1 |
| 0V***96 | Bolt 1.125 In. (2.86 cm) Long | 2 |
6i-1370 Filter Gp-Primary Fuel
| 0S***14 | Bolt (.25" Diameter-.50" Long) | 3 |
| 2S***83 | Bolt (3.25" Long-Drilled Head) | 1 |
| 4F***57 | Screw,Cap,Hexagon H Shock Mount To Bracket | 8 |
2w-3282 Filter Gp-Secondary Fuel
| 1L***69 | Ring-Retaining | 1 |
| 2H***29 | Ring - Retaining External | 1 |
| 2J***57 | Packing,Preformed Screw Assembly Part Of Kit P/N 5r***25 | 1 |
2w-6559 Governor Gp
| 03***16 | Bolt-Self Locking; (1/4unc X 3/4) | 3 |
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 6 |
| 15***28 | Gasket-Governor | 1 |
2w-2410 Governor Gp
| 03***47 | Elbow-Filtered Fuel From Based Assembly | 1 |
| 1R***50 | Filter As-Fuel; (Advanced Efficiency)(Secondary) | 1 |
| 2W***10 | Governor Group | 1 |
8w-6265 Lines Gp-Fuel
| 03***16 | Bolt-Self Locking; (1/4unc X 3/4) | 3 |
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 6 |
| 15***28 | Gasket-Governor | 1 |
4p-9330 Lines Gp-Fuel Injection
| 20***47 | Hose As | 1 |
| 2M***80 | Seal--To Connector Pump Outlet | 1 |
| 2T***43 | Hose As | 1 |
113-5341 Lines Gp-Fuel Injection
| 11***41 | Lines Group-Fuel Injection | 1 |
| 12***05 | Bracket Assem. | 1 |
| 1W***68 | Clamp-Fuel Line; (Non-Threaded)(Thru Hole) | 4 |
4p-9331 Lines Gp-Fuel Injection
| 10***53 | Line As-Fuel Injection; (Cyl No. 3) | 1 |
| 10***54 | Line As-Fuel Injection; (Cyl No. 4) | 1 |
| 1W***67 | Clamp As-Fuel Line (With Spacer) | 2 |
119-8731 Lines Gp-Fuel Injection
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
128-7984 Protection Gp-Fuel System
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 2 |
| 0S***91 | Screw,Cap,Hexagon Bearing Retainer; Part Of Kit P/N 1w***82 | 1 |
| 0T***55 | Bolt; (3/8-16x4.25-In)(Location S) | 1 |
4p-9827 Pump Gp-Fuel Injection
| 1W***95 | Pump Group-Fuel Transfer | 1 |
| 4B***65 | Screw,Cap,Hexagon Fuel Injection Pump | 1 |
| 4F***57 | Screw,Cap,Hexagon H Shock Mount To Bracket | 1 |
111-3769 Pump Gp-Fuel Injection
| 11***69 | Pump Group-Fuel Injection | 1 |
| 1W***87 | Valve As-Check; (Fuel Injection Pump) | 1 |
| 4P***30 | Plunger & Barrel Assem. | 1 |
4n-3287 Pump Gp-Fuel Priming
| 0S***15 | Bolt 19 mm (.75 In.) Long Return Air Console To Enclosed Rops | 4 |
| 11***70 | Camshaft Group | 1 |
| 11***71 | Camshaft-Fuel Pump | 1 |
1w-1695 Pump Gp-Fuel Transfer
| 0S***16 | Screw,Cap,Hexagon H Receptacle Mtg; Bolt Brackets To Firewall Assembly | 1 |
| 10***08 | Pump As; (Fuel Priming) | 1 |
| 1P***36 | Gasket; (Fuel Priming Pump)(Fuel Priming Pump) | 1 |
2w-4160 Pump & Mtg Gp-Fuel Transfer
| 12***94 | Bolt-Tamperproof; (28.58mm) | 1 |
| 12***96 | Bolt-Tamperproof; (95.25mm) | 1 |
| 2W***60 | Pump Group-Fuel Transfer & Mtg; Fuel Transfer Pump And Mounting Group | 1 |
113-5342 Pump Gp-Gov & Fuel Inj
| 03***79 | Seal-O-Ring (Id=10.82mm) | 1 |
| 11***69 | Pump Group-Fuel Injection | 1 |
| 11***62 | Control Group-Fuel Ratio (Basic) | 1 |
128-8807 Pump Gp-Gov & Fuel Inj
| 11***69 | Pump Group-Fuel Injection | 1 |
| 11***62 | Control Group-Fuel Ratio (Basic) | 1 |
| 11***49 | Setscrew-Socket | 1 |
7c-8992 Seal Gp-Pump
| 03***79 | Seal-O-Ring (Id=10.82mm) | 1 |
| 11***69 | Pump Group-Fuel Injection | 1 |
| 11***62 | Control Group-Fuel Ratio (Basic) | 1 |
126-6222 Tank Gp-Fuel
| 00***86 | Connector-Hose (1/4-18nptf Thd) | 1 |
| 12***22 | Tank Group-Fuel | 1 |
| 14***65 | Tank As-Fuel | 1 |
8w-6262 Tank Gp-Fuel
| 03***79 | Seal-O-Ring (Id=10.82mm) | 1 |
| 14***77 | Gasket | 1 |
| 15***26 | Gasket | 1 |
169-3675 Tank Gp-Fuel
| 00***86 | Connector-Hose (1/4-18nptf Thd) | 1 |
| 12***06 | Stud | 8 |
| 12***71 | Hood As | 1 |
Hydraulic System
9j-9865 Accumulator Gp-Hydraulic
| 16***50 | Accumulator Group-Hydraulic; -Blade Cushion | 1 |
| 9J***65 | Accumulator Group; -Charged-Blade Cushion | 1 |
8x-8099 Accumulator & Mtg Gp-Hydraulic
| 16***49 | Clamp | 2 |
| 16***50 | Accumulator Group-Hydraulic; -Blade Cushion | 2 |
| 16***58 | Plate As | 1 |
162-7451 Accumulator & Mtg Gp-Hydraulic -Blade Cushion
| 16***51 | Accumulator & Mtg Group-Hydraulic; -Blade Cushion | 2 |
| 2A***69 | Wiring Group-Blade Cushion | 1 |
| 8X***33 | Lines Group-Accumulator | 1 |
8x-9747 Accumulator Ar-Blade Cushion
| 1H***28 | Seal (3.73 In. Inside Diameter) | 2 |
| 2K***30 | Ring-Back-Up | 2 |
| 3D***24 | O-Ring - For Oil Drain & Level Plug (Items 3 & 7) | 1 |
162-7450 Accumulator Gp-Hydraulic -Charged
| 11***10 | Protector-Gas Valve | 1 |
| 13***23 | Piston | 1 |
| 16***50 | Accumulator Group-Hydraulic; -Blade Cushion | 1 |
179-9398 Accumulator Gp-Hydraulic -Uncharged
| 17***98 | Accumulator Group-Hydraulic; -Uncharged | 1 |
| 7I***22 | Valve & Linkage Group; -4-Bank, Rh; 5-Bank, Lh | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
156-8082 Control Ar-Hydraulic
| 15***82 | Control Ar-Hydraulic | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 8 |
| 4D***33 | Clip (Large) | 2 |
115-0815 Control Ar-Hydraulic
| 11***15 | Control Ar-Hydraulic | 1 |
| 15***64 | Valve & Linkage Group; -6-Bank, Rh, Lh | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
156-8081 Control Ar-Hydraulic -Rh-Plow/Dozer Lift-Ripper-Wing Lift/Tilt
| 15***66 | Valve & Linkage Group; -6-Bank, Rh; 7-Bank, Lh | 1 |
| 15***81 | Control Ar-Hydraulic; -Rh-Plow/Dozer Lift-Ripper-Wing Lift/Tilt | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
107-3854 Control Ar-Hydraulic
| 10***54 | Control Ar-Hydraulic | 1 |
| 11***99 | Valve & Linkage Group; -5-Bank, Rh, Lh | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
2a-6899 Control Ar-Hydraulic
| 10***56 | Valve & Linkage Group; -5-Bank, Rh; 7-Bank, Lh | 1 |
| 2A***99 | Control Ar-Hydraulic | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
112-5510 Control Ar-Hydraulic
| 11***10 | Control Ar-Hydraulic | 1 |
| 11***05 | Valve & Linkage Group; -6-Bank, Rh; 7-Bank, Lh | 1 |
| 8X***42 | Lines Group-Ripper | 1 |
8x-7565 Control Gp-Centershift Lock
| 2K***20 | Washer | 12 |
| 6E***60 | Cylinder Group-Articulation; -Rh | 1 |
| 7K***17 | Washer; 63.5mm(2.50in)Od | 4 |
8w-2913 Cylinder & Mtg Gp-Scarifier
| 11***75 | Cylinder Group-Sideshift | 1 |
| 11***62 | Bracket | 1 |
| 1B***86 | Bolt-Bracket Assembly To Timing Gear | 1 |
112-5361 Cylinder & Mtg Gp-Articulation
| 11***61 | Cylinder & Mtg Group-Articulation | 1 |
| 13***90 | Cylinder Group-Articulation; -Rh | 1 |
| 13***92 | Cylinder Group-Articulation; -Lh | 1 |
140-8129 Cylinder & Mtg Gp-Articulation
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 8 |
| 14***29 | Cylinder & Mtg Group-Articulation | 1 |
| 1D***28 | Bolt 8.26 cm(3.25 In.) Long | 4 |
8x-1947 Cylinder & Mtg Gp-Blade Lift
| 0S***73 | Bolt (102mm Long); (1/2-13x4-In) | 8 |
| 13***29 | Cylinder Group-Lift; -Blade | 2 |
| 1D***28 | Bolt 8.26 cm(3.25 In.) Long | 4 |
8x-1943 Cylinder & Mtg Gp-Blade Tip
| 13***91 | Cylinder Group-Hydraulic; -Blade Tip | 1 |
| 2G***67 | Spacer | 2 |
| 3B***29 | Pin-Cotter | 1 |
8x-1944 Cylinder & Mtg Gp-Centershift
| 16***10 | Cylinder Group-Scarifier | 1 |
| 5P***28 | Capscrew; (Hex Hd) (1/2-13 Unc X 1.00, Gd 8 Z) | 4 |
| 6G***87 | Lock | 2 |
112-7463 Cylinder & Mtg Gp-Sideshift
| 11***63 | Cylinder & Mtg Group-Sideshift | 1 |
| 2F***57 | Nut-Slotted | 1 |
| 2H***86 | Nut-Jam; (1-14-Thd) | 2 |
8w-2290 Cylinder & Mtg Gp-Steering
| 13***41 | Cylinder Group-Steering; -Lh | 1 |
| 13***42 | Cylinder Group-Steering; -Rh | 1 |
| 13***36 | Tie Rod Group; (Steering) | 2 |
8w-2737 Cylinder & Mtg Gp-Wheel Lean
| 16***90 | Seal As-Buffer | 1 |
| 16***00 | Seal-U-Cup | 1 |
| 16***52 | Seal-Wiper | 1 |
137-6790 Cylinder Gp-Articulation -Rh
| 13***90 | Cylinder Group-Articulation; -Rh | 1 |
| 13***91 | Cylinder As | 1 |
| 13***94 | Rod As | 1 |
9t-8784 Cylinder Gp-Articulation
| 13***93 | Cylinder As | 1 |
| 13***94 | Rod As | 1 |
| 13***30 | Piston | 1 |
137-6792 Cylinder Gp-Articulation -Lh
| 00***63 | Ring | 1 |
| 13***92 | Cylinder Group-Articulation; -Lh | 1 |
| 2D***52 | Bearing | 2 |
6e-1560 Cylinder Gp-Articulation
| 15***05 | Head | 1 |
| 17***79 | Bolt-Hex Head; (M24x3.0x80mm) | 1 |
| 18***25 | Kit-Seal; (Articulation Cylinder) | 1 |
6e-1549 Cylinder Gp-Blade Tip
| 14***93 | Head | 1 |
| 16***95 | Seal As-Buffer | 1 |
| 16***04 | Seal-U-Cup | 1 |
6e-1343 Cylinder Gp-Centershift
| 13***94 | Cylinder As | 1 |
| 13***95 | Rod As | 1 |
| 16***86 | Seal As-Buffer | 1 |
131-7191 Cylinder Gp-Hydraulic
| 12***80 | Head | 1 |
| 12***92 | Cylinder As | 1 |
| 12***93 | Rod As | 1 |
132-4929 Cylinder Gp-Lift -Blade
| 11***55 | Cylinder As | 1 |
| 11***56 | Rod As | 1 |
| 13***29 | Cylinder Group-Lift; -Blade | 1 |
6e-1338 Cylinder Gp-Lift
| 12***93 | Rod As | 1 |
| 13***28 | Cylinder As | 1 |
| 14***93 | Head | 1 |
113-7754 Cylinder Gp-Ripper
| 11***54 | Cylinder Group-Ripper | 1 |
| 16***90 | Seal As-Buffer | 1 |
| 16***00 | Seal-U-Cup | 1 |
165-2510 Cylinder Gp-Scarifier
| 11***35 | Rod As | 1 |
| 15***80 | Washer-Hard; (26x44x22-mm Thk) | 1 |
| 16***10 | Cylinder Group-Scarifier | 1 |
112-5575 Cylinder Gp-Sideshift
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 11***75 | Cylinder Group-Sideshift | 1 |
| 1N***99 | Plug-O-Ring; (Straight Thread) | 1 |
9t-2395 Cylinder Gp-Steering -Lh
| 13***44 | Cylinder As; (Lh) | 1 |
| 14***92 | Boss As | 1 |
| 15***79 | Rod | 1 |
9t-2393 Cylinder Gp-Steering -Rh
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 1N***99 | Plug-O-Ring; (Straight Thread) | 1 |
| 1U***98 | Seal Assem. | 1 |
130-9042 Cylinder Gp-Steering -Rh
| 12***45 | Rod As | 1 |
| 12***76 | Cylinder As | 1 |
| 13***42 | Cylinder Group-Steering; -Rh | 1 |
130-9041 Cylinder Gp-Steering -Lh
| 00***39 | Bearing-Aligning; (Self Aligning) | 1 |
| 13***41 | Cylinder Group-Steering; -Lh | 1 |
| 13***45 | Cylinder As; (Rh) | 1 |
121-9242 Cylinder Gp-Wheel Lean
| 10***74 | Retainer | 1 |
| 10***75 | Retainer | 1 |
| 10***23 | Spring | 1 |
108-4916 Detent Gp-Control Valve -Plow, Bulldozer Lift
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 10***96 | Motor Group-Gerotor; -Circle Drive | 1 |
| 10***16 | Detent Group-Control Valve; -Plow, Bulldozer Lift | 1 |
110-4656 Drive Gp-Circle
| 10***06 | Hose As | 1 |
| 11***56 | Drive Group-Circle | 1 |
| 13***44 | Hose As | 1 |
5t-0570 Drive Gp-Circle
| 0S***85 | Bolt; 12.7 mm (1/2") Diameter X 38.1 mm (1 1/2") Length Generator To Engine | 4 |
| 10***96 | Motor Group-Gerotor; -Circle Drive | 1 |
| 10***28 | Bearing-Sleeve | 1 |
8x-9733 Lines Gp-Accumulator
| 11***42 | Hose As | 1 |
| 14***73 | Hose As-Orfs | 1 |
| 14***75 | Hose As | 1 |
142-7378 Lines Gp-Centershift Lock
| 11***99 | Hose As | 1 |
| 11***00 | Hose As | 1 |
| 14***78 | Lines Group-Centershift Lock | 1 |
8x-6070 Lines Gp-Hydraulic -Scarifier
| 10***43 | Hose As | 2 |
| 10***44 | Hose As | 2 |
| 10***49 | Hose As | 2 |
155-4077 Lines Gp-Hydraulic -Bulldozer Lift, Plow, Lh
| 10***86 | Tube | 1 |
| 11***11 | Hose As | 1 |
| 13***06 | Tube As | 1 |
110-2985 Lines Gp-Hydraulic -Rh
| 11***85 | Lines Group-Hydraulic; -Rh | 1 |
| 11***27 | Hose As | 2 |
| 14***18 | Connector As | 1 |
106-4787 Lines Gp-Hydraulic -Lh
| 10***87 | Lines Group-Hydraulic; -Lh | 1 |
| 10***43 | Hose As | 2 |
| 10***44 | Hose As | 2 |
114-0025 Lines Gp-Hydraulic -Bulldozer Lift, Plow, Lh
| 11***25 | Lines Group-Hydraulic; -Bulldozer Lift, Plow, Lh | 1 |
| 11***26 | Hose As | 2 |
| 14***18 | Connector As | 1 |
8w-6251 Lines Gp-Pump
| 11***37 | Hose As | 2 |
| 1S***94 | Clip-R.H. Side Engine Support | 2 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
109-7027 Lines Gp-Ripper
| 10***02 | Hose As | 2 |
| 10***03 | Hose As | 1 |
| 10***08 | Hose As | 1 |
8x-9142 Lines Gp-Ripper
| 10***72 | Hose As | 1 |
| 1S***18 | Clip (Large) | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 4 |
8x-1969 Lines Gp-Steering
| 10***02 | Hose As | 3 |
| 10***03 | Hose As | 1 |
| 10***08 | Hose As | 1 |
142-8205 Lock Gp-Centershift
| 11***40 | Cylinder | 1 |
| 11***41 | Pin | 1 |
| 14***87 | Cap | 1 |
8x-1945 Lock Gp-Centershift
| 11***40 | Cylinder | 1 |
| 11***41 | Pin | 1 |
| 14***87 | Cap | 1 |
7t-6517 Manifold Gp-Control -Accumulator
| 14***10 | Valve Group-Solenoid; -Axle Oil Cooler-Hydraulic Lockout | 1 |
| 7T***17 | Manifold Group-Control; (Solenoid) | 1 |
| 8C***62 | Manifold | 1 |
105-3196 Motor Gp-Gerotor
| 10***96 | Motor Group-Gerotor; -Circle Drive | 1 |
| 11***59 | Mounting As | 4 |
| 1A***22 | Bolt-Generator To Flywheel Housing | 4 |
8x-2378 Pump & Mtg Gp-Piston
| 1M***80 | Bearing; (25.413 mm Od) | 4 |
| 2B***73 | Key-Woodruff | 2 |
| 2D***09 | Seal--To Cover & Plate Bearing Retainers | 3 |
6y-8765 Pump Gp-Gear
| 11***60 | Kit-Seal; (Hmu Steering) | 1 |
| 3G***91 | Race | 2 |
| 5L***00 | Bearing-Thrust | 1 |
6y-8764 Pump Gp-Gear
| 4F***52 | Packing,Preformed Cover Part Of Kit P/N 4j***80 | 1 |
| 6V***20 | Bolt; (M10x1.5x30-mm) | 3 |
| 6Y***64 | Pump Group-Gear; -Transmission | 2 |
102-1501 Pump Gp-Metering -Hmu
| 00***12 | Cup-Roller Bearing | 1 |
| 00***63 | Ring | 1 |
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
6e-3137 Pump Gp-Piston
| 10***10 | Plate | 2 |
| 10***11 | Plate-Spacer | 2 |
| 3J***00 | Ring-Retaining | 1 |
100-3412 Rotating Gp-Pump
| 0L***78 | Bolt 44.45 mm(1.75 In.) Long | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 10***12 | Rotating Group-Pump; -Implement, Steering | 1 |
7d-9600 Shaft Gp-Pump Drive
| 0L***78 | Bolt 44.45 mm(1.75 In.) Long | 4 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 4 |
| 11***95 | Universal Joint Group-Pump Drive; -Steering | 1 |
100-3416 Swashplate Gp -Variable
| 10***16 | Swashplate Group; -Variable | 1 |
| 2H***28 | Seal-Top Cover & Filter Group | 7 |
| 3H***07 | Seal-O-Ring; (21.82mm Id) | 4 |
9t-5604 Swivel Gp
| 17***07 | Seal | 2 |
| 17***08 | Rotor | 1 |
| 17***09 | Retainer | 1 |
260-6502 Swivel Gp
| 08***07 | Pin | 1 |
| 0L***51 | Bolt Starting Engine Fuel Tank Bracket To Diesel Intake Manifold | 2 |
| 0S***09 | Bolt (3/4") Filler Tube Assembly To Transfer Drive Case | 2 |
9t-7984 Tank & Filter Gp-Hydraulic
| 08***07 | Pin | 1 |
| 14***61 | Spacer; (20x128x6-mm Thk) | 1 |
| 1L***72 | Dowel (Part Of 8s***99 Assem.) | 1 |
214-1984 Tank & Filter Gp-Hydraulic
| 1R***22 | Filter Element As-Oil; (Standard Efficiency)(Disposable) | 1 |
| 21***84 | Tank & Filter Group-Hydraulic | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 8 |
8x-2369 Tank & Mtg Gp-Hydraulic
| 21***84 | Tank & Filter Group-Hydraulic | 1 |
| 4D***94 | Clip-- Compressor Clutch Wire To Compressor Body | 3 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 1 |
214-1983 Tank & Mtg Gp-Hydraulic
| 21***83 | Tank & Mtg Group-Hydraulic | 1 |
| 2Y***55 | Fitting | 3 |
| 5Y***66 | Yoke As-Slip | 1 |
112-5495 Universal Joint Gp-Pump Drive
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
5y-0769 Universal Joint Gp-Pump Drive
| 02***87 | Fitting-Grease; (Universal Joint) | 1 |
| 0L***78 | Bolt 44.45 mm(1.75 In.) Long | 8 |
| 5H***93 | Retainer-Felt | 1 |
112-2240 Manifold Gp-Control
| 11***40 | Valve & Mounting Group; -Blade Cushion | 1 |
| 6Y***32 | Bearing-Thrust | 1 |
| 6Y***33 | Ring-Thrust | 2 |
153-7964 Valve & Linkage Gp -6-Bank, Rh, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 2 |
153-7966 Valve & Linkage Gp -6-Bank, Rh; 7-Bank, Lh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
7i-4622 Valve & Linkage Gp -4-Bank, Rh; 5-Bank, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
8x-1949 Valve & Linkage Gp -4-Bank, Rh, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
7i-4621 Valve & Linkage Gp -5-Bank, Rh, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
7i-4623 Valve & Linkage Gp -Bank 5-Rh-Bank 6-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
112-5499 Valve & Linkage Gp -5-Bank, Rh, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 2 |
8x-4280 Valve & Linkage Gp -Bank 5-Rh-Bank 7-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 1 |
115-0805 Valve & Linkage Gp -Bank 6-Rh-Bank 7-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 2 |
7i-4624 Valve & Linkage Gp -4-Bank, Rh; 5-Bank, Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 1 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 1 |
| 10***19 | Plate As; (Rh) | 1 |
107-3856 Valve & Linkage Gp -Bank 5-Rh-Bank 7-Lh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 2 |
| 10***19 | Plate As; (Rh) | 1 |
115-0791 Valve & Linkage Gp -Bank 6-Lh,Rh
| 10***57 | Lever; (Plow, Bulldozer Angle) | 2 |
| 10***58 | Lever; (Plow & Bulldozer Lift) | 3 |
| 10***97 | Lever; (Plow, Bulldozer Angle) | 2 |
6e-3032 Valve Gp-Bank 4 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 5 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
6e-3038 Valve Gp-Bank 4 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8671 Valve Gp-Bank 5 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 7 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8645 Valve Gp-Bank 5 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8646 Valve Gp-Bank 5 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 6 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
104-8648 Valve Gp-Bank 6 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 7 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
153-8910 Valve Gp-Bank 6 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 7 |
| 10***46 | Cover | 1 |
| 10***38 | Manifold | 1 |
153-8911 Valve Gp-Bank 6 -Rh
| 10***00 | Film-Notice | 1 |
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***85 | Manifold | 1 |
115-1008 Valve Gp-Bank 6 -Rh
| 10***09 | Seal-Integral, . Gear; Ring | 7 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8647 Valve Gp-Bank 7 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
104-8651 Valve Gp-Bank 7 -Lh
| 10***09 | Seal-Integral, . Gear; Ring | 8 |
| 10***46 | Cover | 1 |
| 10***85 | Manifold | 1 |
153-8912 Valve Gp-Bank 7 -Lh
| 10***44 | Valve | 1 |
| 15***12 | Valve Group-Bank 7; -Lh | 1 |
| 3P***98 | Plug-Orifice | 1 |
6e-2866 Valve Gp-Combination
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 12***98 | Insert | 1 |
| 1H***37 | Valve | 1 |
9t-5957 Valve Gp-Combination
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 13***50 | Valve Group-Purge; -Hydraulic Steering-Implement Signal | 1 |
| 14***08 | Plug As. | 3 |
107-0547 Valve Gp-Control -Dozer Lift, Plow
| 10***47 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
115-1007 Valve Gp-Control -Bulldozer Angle, Plow, Rh
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
153-8905 Valve Gp-Control -Wing Lift
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
6e-3034 Valve Gp-Control -Blade Tip
| 10***55 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
137-8106 Valve Gp-Control -Wing Lift
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
107-0543 Valve Gp-Control -Scarifier
| 10***48 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
153-8906 Valve Gp-Control -Wing Tilt
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***80 | Housing | 1 |
153-8908 Valve Gp-Control -Plow Angle
| 03***27 | Seal-O-Ring; (19.18mm Id) | 1 |
| 03***36 | Seal-O-Ring | 1 |
| 10***14 | Body-Compensator | 1 |
137-8104 Valve Gp-Control -Wing Tilt
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
6e-3029 Valve Gp-Control -Centershift
| 10***54 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
6e-3031 Valve Gp-Control -Blade Lift
| 10***50 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
6e-3037 Valve Gp-Control -Bulldozer
| 10***50 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***72 | Detent | 1 |
107-0549 Valve Gp-Control
| 10***29 | Plug | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
6e-3028 Valve Gp-Control -Articulation
| 10***49 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
107-0545 Valve Gp-Control -Ripper
| 10***47 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
153-8907 Valve Gp-Control -Bulldozer Lift, Plow, Lh
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
107-0552 Valve Gp-Control -Wing Tilt
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
6e-3035 Valve Gp-Control -Circle Drive
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***73 | Retainer | 4 |
| 10***78 | Cover | 1 |
6e-3036 Valve Gp-Control -Sideshift
| 10***50 | Stem | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
| 10***72 | Detent | 1 |
6e-3030 Valve Gp-Control -Wheel Lean
| 10***50 | Stem | 1 |
| 10***70 | Lever As; (Blade Lift) | 1 |
| 10***71 | Lever; (Blade Lift) | 1 |
104-3122 Valve Gp-Pump Control -Pressure, Flow Compensator
| 10***22 | Valve Group-Pump Control; -Pressure, Flow Compensator-Implement, Steering | 1 |
| 10***44 | Valve | 1 |
| 13***70 | Sleeve | 1 |
131-8350 Valve Gp-Purge
| 13***50 | Valve Group-Purge; -Hydraulic Steering-Implement Signal | 1 |
| 3K***60 | Seal Pilot Manifold On; Seal To Boom Check Valve Drain | 2 |
| 4T***42 | Spring | 1 |
222-7774 Valve Gp-Relief
| 03***21 | Ring-Back-Up | 1 |
| 1H***23 | Packing,Preformed Part Of Kit P/N 5r***25 | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
6e-3033 Valve Gp-Relief
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 4D***97 | Seal 15.6 mm(.614 In.) I.D. | 1 |
| 6E***33 | Valve Group-Relief; -Plow/Dozer Lift-Blade Lift | 1 |
139-8472 Valve Gp-Relief
| 11***35 | Retainer As | 1 |
| 13***77 | Valve | 1 |
| 13***72 | Valve Group-Relief; -Ripper | 1 |
106-7388 Valve Gp-Relief
| 10***88 | Valve Group-Relief; -Blade Tip | 1 |
| 11***54 | Valve | 1 |
| 11***35 | Retainer As | 1 |
106-7390 Valve Gp-Relief
| 10***90 | Valve Group-Relief; -Blade Lift | 1 |
| 11***35 | Retainer As | 1 |
| 13***77 | Valve | 1 |
139-8474 Valve Gp-Relief
| 13***74 | Valve Group-Relief; -Lift | 1 |
| 14***03 | Seal-O-Ring | 1 |
| 14***04 | Ring-Backup | 2 |
100-6021 Valve Gp-Relief
| 10***21 | Valve Group-Relief; -Direct Operated | 1 |
| 10***48 | Valve Group-Relief; -Blade Tip, Ripper, Sideshift | 1 |
| 10***89 | Valve Group-Relief; -Blade Tip, Ripper, Sideshift | 1 |
6e-4702 Valve Gp-Relief
| 3G***26 | Nut; (3/8-40-Thd) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
| 4D***97 | Seal 15.6 mm(.614 In.) I.D. | 1 |
101-4147 Valve Gp-Relief
| 10***47 | Valve Group-Relief; -Blade Tip-Ripper-Sideshift | 1 |
| 11***35 | Retainer As | 1 |
| 2P***79 | Locknut- Tube Assembly To Upper Frame | 1 |
106-7389 Valve Gp-Relief
| 10***89 | Valve Group-Relief; -Blade Tip, Ripper, Sideshift | 1 |
| 11***35 | Retainer As | 1 |
| 13***77 | Valve | 1 |
101-4145 Valve Gp-Relief
| 10***45 | Valve Group-Relief; -Scarifier-Lh-Blade Tip | 1 |
| 3G***26 | Nut; (3/8-40-Thd) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
6e-4704 Valve Gp-Relief
| 10***88 | Valve Group-Relief; -Blade Tip | 1 |
| 6E***02 | Valve Group-Relief; -Blade Tip | 1 |
| 6E***04 | Valve Group-Relief; -Blade Lift | 1 |
6e-4703 Valve Gp-Relief
| 10***57 | Valve | 1 |
| 12***61 | Housing | 1 |
| 3J***54 | Packing,Preformed Part Of Kit P/N 5r***27 | 1 |
4t-4935 Valve Gp-Relief
| 10***90 | Valve Group-Relief; -Blade Lift | 1 |
| 3G***26 | Nut; (3/8-40-Thd) | 1 |
| 3J***07 | Seal Valve Assembly To; Seal- Tube Assembly To Logic Valve | 1 |
101-4148 Valve Gp-Relief
| 10***48 | Valve Group-Relief; -Blade Tip, Ripper, Sideshift | 1 |
| 11***54 | Valve | 1 |
| 11***35 | Retainer As | 1 |
4t-1860 Valve Gp-Shuttle
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 2 |
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 14***87 | Coil As; (24-Volt) | 1 |
152-8346 Valve Gp-Solenoid
| 10***39 | Spacer; (18.85x26.67x78-mm Thk)(3.91mm Thk) | 8 |
| 10***55 | Bearing-Sleeve | 1 |
| 10***80 | Bracket As | 4 |
149-2610 Valve Gp-Solenoid
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***36 | Kit-Seal; (Solenoid Valve) | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
152-8351 Valve Gp-Solenoid
| 10***39 | Spacer; (18.85x26.67x78-mm Thk)(3.91mm Thk) | 8 |
| 10***55 | Bearing-Sleeve | 1 |
| 10***80 | Bracket As | 4 |
8t-8808 Valve Gp-Solenoid
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
| 14***11 | Cartridge Assem. | 1 |
| 18***72 | Coil As | 1 |
149-2658 Valve Gp-Solenoid
| 10***36 | Kit-Seal; (Solenoid Valve) | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
| 14***58 | Valve Group-Solenoid; -Blade Lock | 1 |
Implements
110-5339 Circle Gp
| 11***39 | Circle Group | 1 |
| 12***07 | Plate | 2 |
| 12***54 | Strip-Wear | 11 |
110-8078 Circle Gp
| 06***60 | Ring-Retaining | 1 |
| 11***78 | Circle Group; -Blade | 1 |
| 15***13 | Adapter; (3-Ft)(Inside) | 2 |
8x-1960 Drawbar Gp
| 1J***62 | Bolt-Plow | 10 |
| 5F***33 | Bolt-Plow; (3/4-10x3.75-In) | 6 |
| 6Y***05 | Bit-End (Overlay) | 2 |
Lubrication System
4p-7096 Base Gp-Oil Filter
| 4P***96 | Base Group-Oil Filter; -Engine | 1 |
| 5S***18 | Push Rod,Engine Pop Valve Lifter | 12 |
| 7C***13 | Valve Mechanism Group | 1 |
8n-4457 Base Gp-Oil Filter
| 03***51 | Elbow )-Inlet Port To Valve Group | 1 |
| 1B***90 | Bolt; (5/16-18x1.375-In)(Rh Front Cover) | 2 |
| 1B***75 | Bolt (" " " ); Bolt ( " " " ) | 1 |
147-3092 Base Gp-Oil Filter
| 0S***18 | Bolt; (5/16-18x1-In)(Hydraulic Pump) | 2 |
| 14***92 | Base Group-Oil Filter | 1 |
| 1B***90 | Bolt; (5/16-18x1.375-In)(Rh Front Cover) | 2 |
1p-4244 Breather Gp -Crankcase
| 0S***88 | Bolt,Machine; Hose Assembly Mounting,Hose Assembly To Transmission,And To Torque Converter | 8 |
| 13***75 | Cover-Filter Base | 1 |
| 14***82 | Cover-Filter Base | 1 |
2p-6855 Filler Gp-Engine Oil
| 2P***55 | Filler Group-Oil | 1 |
| 2W***62 | Breather As-Crankcase; (Engine) | 1 |
| 3H***43 | Bolt,Machine Breather Assembly To Cover | 1 |
147-3091 Filter Gp-Engine Oil
| 14***91 | Filter Group-Engine Oil | 1 |
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 2 |
| 2A***11 | Washer; (5.5x12.3x0.8-mm Thk) | 1 |
136-3171 Fumes Disposal Gp
| 13***71 | Fumes Disposal Group | 1 |
| 1N***24 | Tube | 1 |
| 1N***02 | Hose 8.00 cm(3.15 In.) | 1 |
8n-7254 Fumes Disposal Gp
| 03***50 | Elbow (Check Valve Drain Tube) | 1 |
| 14***83 | Hose As | 1 |
| 14***84 | Hose As | 1 |
115-7542 Gauge Gp-Oil Level (Dipstick) -Engine
| 11***42 | Gage Group-Oil Level; -Engine | 1 |
| 2P***47 | Filler Neck Oil Gage | 1 |
| 2P***97 | Tube A Oil Level Gage | 1 |
2p-6493 Gauge Gp-Oil Level (Dipstick) -Engine
| 2P***93 | Gauge Group-Oil Level (Dipstick); -Engine | 1 |
| 4L***59 | Bolt-Mirror To Open Rops | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 1 |
2p-6105 Lines Gp-Engine Oil
| 2P***97 | Tube A Oil Level Gage | 1 |
| 2P***05 | Lines Group-Engine Oil; Engine Oil Lines Group | 1 |
| 4P***28 | Tube Assembly | 1 |
147-2070 Lines Gp-Turbocharger Oil
| 03***48 | Elbow (3/4" Tapped Pumps) - 2nd Type | 1 |
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
7e-5683 Lines Gp-Turbocharger Oil
| 0L***64 | Lock --To Reverse Driven Gear Splash Pan; -- To Reverse Driven Gear Splash Pan | 1 |
| 0L***70 | Bolt (2-1/4") Filler Tube Assembly To Transfer Drive Case | 1 |
| 0S***71 | Screw,Cap,Hexagon; Tube Assembly To Turbocharger And Elbow Mounting | 1 |
147-2071 Lines Gp-Turbocharger Oil
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 1 |
139-9609 Mounting Gp-Engine Oil Filter
| 0L***43 | Bolt 63.5 mm (3/8" X 2 1/2" -Cover Assembly To Fender | 1 |
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 2 |
| 0S***08 | Bolt-Support To Starting Engine Timing Gear Housing | 1 |
106-8957 Pump Gp-Engine Oil
| 0T***65 | Bolt--3/8" X 3 1/2"--Use As Required; Bolt 5t***56 Plate To Cover Gp 4n***72 | 3 |
| 10***57 | Pump Group-Engine Oil | 1 |
| 1B***09 | Key,Woodruff No. 10 Oil Pump | 1 |
6i-1346 Pump Gp-Engine Oil
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 3 |
| 6I***46 | Pump Group-Engine Oil | 1 |
| 8T***96 | Washer-Hard- Line From Pipe As. To Gear | 3 |
106-8958 Pump Gp-Engine Oil
| 0S***90 | Bolt; (3/8-16x2in)(Clip Thru Spacer To Bracket As) | 3 |
| 0S***19 | Bolt,Machine Gear Retaining Part Of Kit P/N 1w***46 | 1 |
| 10***58 | Pump Group-Engine Oil | 2 |
Machine Arrangement
8w-6228 Chassis Ar
| 10***75 | Axle Group-Front | 1 |
| 10***84 | Hitch Group-Articulating | 1 |
| 11***19 | Box Group-Tool | 1 |
8w-6255 General Ar
| 11***05 | Engine Ar, Piston | 1 |
| 11***78 | Engine Ar | 1 |
| 12***95 | Installation Ar-Engine | 1 |
152-3843 Snow Ar-Motor Grader
| 10***67 | Heater Ar-Cab | 1 |
| 10***18 | Autoshift Ar; -Transmission | 1 |
| 10***72 | Instrument Ar; -Speedometer/Tach | 1 |
152-3838 Snow Ar-Motor Grader
| 10***18 | Autoshift Ar; -Transmission | 1 |
| 10***72 | Instrument Ar; -Speedometer/Tach | 1 |
| 10***96 | Starting Aid Group-Ether | 1 |
Operator Station
142-0742 Accessory Gp-Cab -Low
| 10***87 | Lines Group-Hydraulic; -Lh | 1 |
| 11***85 | Lines Group-Hydraulic; -Rh | 1 |
| 11***56 | Drive Group-Circle | 1 |
142-0747 Accessory Gp-Cab -High
| 11***14 | Rail-Moldboard | 2 |
| 14***47 | Accessory Group-Cab; -High | 1 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 40 |
116-2779 Adjuster Gp-Seat
| 11***79 | Adjuster Group-Seat | 1 |
| 2J***06 | Nut Front Support To Frame; Nut-Front Support To Frame | 36 |
| 5J***73 | Bolt 2.06cm(.8125in.)Long | 36 |
173-1028 Adjuster Gp-Seat
| 17***28 | Adjuster Group-Seat; -Seat | 1 |
| 8W***81 | Plate | 1 |
| 8W***84 | Bracket As | 1 |
8w-7646 Air Conditioner & Mounting Gp
| 7D***76 | Edge-Cutting; (6-Ft Each) | 2 |
| 8W***46 | Air Conditioner & Mounting Group | 1 |
8w-7645 Air Conditioner Ar
| 7D***77 | Edge-Cutting; (7-Ft Each) | 2 |
| 8W***45 | Air Conditioner Ar | 1 |
8c-9788 Air Conditioner Gp
| 11***34 | Spacer; (3-mm Thk) | 3 |
| 11***36 | Angle As | 1 |
| 13***23 | Extension-Rh | 1 |
113-4245 Armrest Gp -Rh
| 0S***56 | Bolt 4 1/4 In. (108 mm) --Front Support Assembly To Frame | 4 |
| 11***45 | Armrest Group; -Rh | 1 |
| 12***87 | Washer-Thrust; (76.6x146x1-mm Thk)(.100 Thk) | 2 |
202-7666 Armrest Gp -Rh
| 10***22 | Plate | 2 |
| 10***23 | Cam As | 2 |
| 10***76 | Pin | 2 |
202-7668 Armrest Gp -Lh
| 10***27 | Lines Group-Ripper | 1 |
| 11***54 | Cylinder Group-Ripper | 1 |
| 14***44 | Ripper Group | 1 |
113-4242 Armrest Gp -Lh
| 11***34 | Spacer; (3-mm Thk) | 3 |
| 11***35 | Angle As | 1 |
| 11***42 | Armrest Group; -Lh | 1 |
134-1220 Blower & Mtg Gp-Cab
| 13***20 | Blower & Mtg Group-Cab | 1 |
| 18***53 | Link As-Lower | 1 |
| 19***86 | Film; (Safety) (To Right And Left Of Fuel Tank) | 2 |
134-1221 Blower Ar-Cab
| 13***21 | Blower Ar-Cab | 1 |
| 14***01 | Link As-Lower | 1 |
| 1K***72 | Locknut Horn To Guard | 10 |
129-7233 Cab Ar
| 11***83 | Scarifier Group; -Straight Type | 1 |
| 11***79 | Bracket Group-Scarifier | 1 |
| 12***33 | Cab Ar | 1 |
125-4341 Cab Ar
| 11***79 | Bracket Group-Scarifier | 1 |
| 12***41 | Cab Ar | 1 |
| 8W***13 | Cylinder & Mounting Group-Scrfr | 1 |
125-4343 Cab Gp
| 10***74 | Bearing | 2 |
| 10***75 | Shaft As | 1 |
| 11***80 | Drawbar As | 1 |
129-8616 Cab Gp
| 10***74 | Bearing | 2 |
| 10***75 | Shaft As | 1 |
| 11***80 | Drawbar As | 1 |
129-7231 Canopy Ar
| 11***59 | Retainer Assembly; (G.E.T.) | 1 |
| 12***31 | Canopy Ar | 1 |
| 13***08 | Pin | 1 |
130-2886 Canopy Gp -High Profile
| 13***86 | Canopy Group; -High Profile | 1 |
| 19***18 | Shank | 9 |
| 5K***58 | Grommet | 9 |
3e-1906 Compressor Gp-Refrigerant
| 11***11 | Socket-Auxiliary Power; (12-Volt)(Power Port) | 1 |
| 12***78 | Locknut; (M6x1-Thd) | 2 |
| 13***65 | Plate | 1 |
7e-6461 Compressor Gp-Refrigerant
| 11***11 | Socket-Auxiliary Power; (12-Volt)(Power Port) | 1 |
| 12***78 | Locknut; (M6x1-Thd) | 2 |
| 13***53 | Plate | 1 |
8w-6333 Condenser & Mtg Gp-Refrigerant
| 11***15 | Angle As; (Rh) | 1 |
| 11***16 | Angle As; (Lh) | 1 |
| 11***27 | Support As | 1 |
8w-5595 Console Gp-Operator -Transmission Direction, Speed
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 10***40 | Cover | 1 |
8x-2330 Console Gp-Operator
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 11***40 | Bracket As-Lh | 1 |
| 1F***50 | Nut Rops Support | 1 |
129-8215 Control Gp-Clutch
| 0S***94 | Bolt (1 In. Long 3/8 In. Dia.); Plate Assembly To Support Assembly | 1 |
| 11***43 | Bracket As-Rh | 1 |
| 12***15 | Control Group-Clutch; -Inching Pedal | 1 |
7i-4718 Control Gp-Steering
| 10***90 | Plate | 1 |
| 12***40 | Blower Group-Cab | 1 |
| 13***30 | Film-Control; (Heat & A/C Blower) | 1 |
8x-4153 Conversion Ar-Non-Rops
| 11***55 | Spring-Filter | 4 |
| 13***20 | Blower & Mtg Group-Cab | 1 |
| 13***71 | Plate | 1 |
8x-4527 Door Gp-Cab
| 10***72 | Glass; (Rear)(High Profile) | 1 |
| 10***53 | Mounting | 4 |
| 10***15 | Pad (Rh) | 1 |
8x-4413 Door Gp-Cab -High Profile
| 11***95 | Cab As-Non-Rops | 1 |
| 12***44 | Mounting Group-Cab; -Non-Rops, Enclosed | 1 |
| 12***45 | Wiper Group-Window; -Cab Front Window | 1 |
8x-4318 Door Gp-Cab -High Profile-Lh
| 12***42 | Washer Group-Window; -Front | 1 |
| 12***16 | Cab Group | 1 |
| 13***60 | Wiring Group-Cab | 1 |
8x-4526 Door Gp-Cab -Low Profile
| 12***75 | Panel Group-Cab; -Instrument | 1 |
| 13***86 | Canopy Group; -High Profile | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 1 |
8x-4525 Door Gp-Cab -Rh
| 12***44 | Mounting Group-Cab; -Non-Rops, Enclosed | 1 |
| 12***18 | Liner Group-Cab; -High Profile | 1 |
| 12***14 | Panel Group-Cab; -High Profile | 1 |
8x-4317 Door Gp-Cab -High Profile-Rh
| 12***42 | Washer Group-Window; -Front | 1 |
| 12***43 | Cab Group | 1 |
| 8W***27 | Insulation Group-Weather | 1 |
8w-7653 Duct & Control Gp
| 10***27 | Bracket | 2 |
| 3E***06 | Compressor Group-Refrigerant | 1 |
| 4L***37 | Hex Head Capscrew, 3/8 Nc X 1 1/2 In. (38 mm) | 6 |
7i-5015 Duct Gp-Cab Air -Air Conditioner, Heater
| 10***20 | Spacer; (10.5x25x20-mm Thk) | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
| 5S***83 | Capscrew; (Hex Hd) (3/8-16 Unc X 1.75 Gr8) | 2 |
8y-5874 Extension Gp-Backrest -Cloth
| 10***20 | Spacer; (10.5x25x20-mm Thk) | 4 |
| 21***18 | Core As-Condenser | 1 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
8y-5959 Extension Gp-Backrest -Vinyl
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 1 |
| 03***66 | Rod | 1 |
| 03***94 | Pin | 1 |
8x-2245 Fan Gp-Circulating -Front Defroster
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
| 13***85 | Adapter | 1 |
| 13***60 | Coupler | 1 |
8x-2920 Fan Gp-Circulating -Rear Defroster
| 12***73 | Bolt-12 Point Head; (3/8-16x1.25-In)(3/8-16thd) | 1 |
| 14***23 | Cable As | 1 |
| 14***38 | Bracket | 1 |
135-1978 Fan Gp-Circulating -Front Defroster
| 10***81 | Gate As | 1 |
| 13***78 | Fan Group-Circulating; -Front Defroster | 1 |
| 14***86 | Cover | 1 |
9x-9657 Fan Gp-Circulating -Rear
| 09***00 | Steering Wheel | 1 |
| 10***01 | Pump Group-Metering; -Steering | 1 |
| 14***95 | Nut; (13/16-20-Thd) | 1 |
8x-2925 Filter Gp-Cab Air
| 10***81 | Gate As | 1 |
| 14***86 | Cover | 1 |
| 14***88 | Cover | 1 |
133-5377 Guard Gp-Vandalism
| 10***81 | Gate As | 1 |
| 13***77 | Guard Group-Vandalism | 1 |
| 14***86 | Cover | 1 |
147-5472 Guard Gp-Vandalism
| 12***75 | Panel Group-Cab; -Instrument | 1 |
| 14***72 | Guard Group-Vandalism | 1 |
| 3V***94 | Plug-Button | 1 |
8w-7651 Heater & Mtg Gp-Cab
| 10***41 | Plate As | 1 |
| 10***50 | Latch As-Rh | 1 |
| 10***52 | Link-Tag-Rh | 1 |
124-2960 Heater & Mtg Gp-Cab
| 10***41 | Plate As | 1 |
| 10***49 | Latch As; (Lh) | 1 |
| 10***51 | Link-Tag-Lh | 1 |
124-2959 Heater Ar-Cab
| 10***41 | Plate As | 1 |
| 10***50 | Latch As-Rh | 1 |
| 10***52 | Link-Tag-Rh | 1 |
102-7367 Heater Ar-Cab
| 10***67 | Heater Ar-Cab | 1 |
| 10***53 | Bumper-Conical | 4 |
| 10***13 | Plate As | 2 |
8c-9787 Heater Gp-Cab
| 10***41 | Plate As | 1 |
| 10***49 | Latch As; (Lh) | 1 |
| 10***51 | Link-Tag-Lh | 1 |
125-9662 Heater Gp-Seat -Light-Duty
| 10***53 | Bumper-Conical | 4 |
| 10***13 | Plate As | 2 |
| 12***28 | Seal; (17.2-cm Each) | 0 |
8x-9440 Horn Gp-Air
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 10***96 | Bracket As | 6 |
| 12***54 | Duct | 1 |
5d-6998 Horn Gp-Air
| 12***56 | Panel As | 1 |
| 5D***98 | Horn Group-Air | 1 |
| 7K***01 | Nut-Speed; (44.5mm Oal) | 2 |
9d-4049 Horn Gp-Air
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***43 | Cushion Kit; (Consists Of Fastener, Cushion Assem.) | 1 |
| 8Y***47 | Fastener | 2 |
113-5808 Housing Gp-Seat Suspension
| 11***08 | Housing Group-Seat Suspension | 1 |
| 8Y***77 | Pan As-Extension | 1 |
| 8Y***47 | Fastener | 2 |
145-1300 Installation Ar-Radio
| 13***78 | Fan Group-Circulating; -Front Defroster | 1 |
| 14***00 | Installation Ar-Radio | 1 |
| 3E***21 | Actuator-Rocker; (Defroster) | 1 |
130-9921 Installation Ar-Radio
| 13***21 | Installation Ar-Radio | 1 |
| 3E***21 | Actuator-Rocker; (Defroster) | 1 |
| 3E***25 | Lamp; (24-Volt) | 1 |
130-9432 Installation Gp-Radio
| 13***32 | Installation Group-Radio | 1 |
| 3E***21 | Actuator-Rocker; (Defroster) | 1 |
| 3E***25 | Lamp; (24-Volt) | 1 |
105-2772 Instrument Ar
| 10***72 | Instrument Ar; -Speedometer/Tach | 1 |
| 1B***13 | Bolt,Machine Governor And Decelerator Control | 1 |
| 1M***30 | Nut And Lock Assem.; (No. 10-32) | 2 |
105-5126 Instrument Gp
| 03***55 | Locknut; (5/16-18-Thd)(Marked X) | 1 |
| 10***26 | Instrument Group | 1 |
| 13***79 | Bracket | 1 |
8w-5927 Insulation Gp-Weather
| 11***55 | Spring-Filter | 4 |
| 13***92 | Retainer-Captive | 2 |
| 23***86 | Filter Element As-Cab Air; (Cab) | 1 |
129-4618 Liner Gp-Cab -High Profile
| 12***62 | Heater Group-Seat; -Light-Duty | 1 |
| 12***18 | Liner Group-Cab; -High Profile | 1 |
| 8M***48 | Fuse-15 Amp; (15 Amp) | 1 |
125-4346 Liner Gp-Cab
| 12***71 | Pad; (420mm X 356mm) | 1 |
| 12***72 | Pad; (1035mm X 150mm) | 1 |
| 12***46 | Liner Group-Cab; -High Profile | 1 |
8x-2400 Liner Gp-Cab -Low Profile-Enclosed
| 13***84 | Plate As | 1 |
| 13***87 | Plate As | 1 |
| 13***91 | Plate As | 1 |
8w-6899 Lines Gp-Air Conditioner
| 7I***15 | Duct Group-Cab Air; -Air Conditioner, Heater | 1 |
| 8W***99 | Lines Group-Air Conditioner | 1 |
| 8W***51 | Heater & Mtg Group-Cab | 1 |
8x-4558 Lines Gp-Heater
| 12***60 | Heater & Mtg Group-Cab | 1 |
| 12***37 | Louver Group-Cab | 1 |
| 8X***58 | Lines Group-Heater | 2 |
6v-1970 Literature Gp
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 10***40 | Cover | 1 |
126-1137 Louver Gp-Cab
| 03***38 | Clamp | 1 |
| 10***26 | Wheel As-Blower | 2 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
123-4358 Mirror Gp-Rear View
| 00***84 | Spring-Horn | 4 |
| 00***85 | Brush-Horn | 4 |
| 09***71 | Seal-Horn Button | 1 |
140-8127 Mirror Gp-Rear View -Dual, Interior
| 14***27 | Mirror Group-Rear View; -Dual, Interior | 1 |
| 2G***64 | Kit-Diaphragm; (Air Horn) | 2 |
| 4B***75 | Washer (1.75 In. Outside Diameter) | 1 |
113-8217 Mirror Gp-Rear View
| 00***84 | Spring-Horn | 4 |
| 00***85 | Brush-Horn | 4 |
| 09***71 | Seal-Horn Button | 1 |
8x-2795 Mirror Gp-Rear View -Inside
| 15***87 | Cover | 2 |
| 2G***64 | Kit-Diaphragm; (Air Horn) | 2 |
| 4B***75 | Washer (1.75 In. Outside Diameter) | 1 |
187-1051 Module Gp-Quad Gauge
| 18***51 | Module Group-Quad Gauge | 1 |
| 2A***84 | Bracket | 1 |
| 2G***67 | Washer; (10.5x60x3-mm Thk) | 1 |
124-0384 Module Gp-Quad Gauge
| 09***78 | Pin-Spring | 1 |
| 10***24 | Kit-Indicator; (Weight Adjustment)(Suspension Seat) | 1 |
| 10***79 | Kit-Bumper; (Weight Adjustment)(Suspension Seat) | 1 |
159-0241 Module Gp-Quad Gauge
| 13***32 | Installation Group-Radio | 1 |
| 14***97 | Converter Group-Electrical; -Radio | 1 |
| 15***41 | Module Group-Quad Gauge | 1 |
149-5927 Module Gp-Quad Gauge
| 13***32 | Installation Group-Radio | 1 |
| 14***27 | Module Group-Quad Gauge | 1 |
| 2A***46 | Converter Group-Electrical | 1 |
125-4344 Mounting Gp-Cab -Non-Rops, Enclosed
| 11***38 | Speedometer As | 1 |
| 11***68 | Tachometer As | 1 |
| 12***44 | Mounting Group-Cab; -Non-Rops, Enclosed | 1 |
2a-6985 Mounting Gp-Rops
| 11***64 | Boot | 14 |
| 2A***85 | Mounting Group-Rops; -Enclosed | 1 |
| 4M***81 | Capscrew; (Hex Hd 1/4-20x3/4) (Use W/Spacer 2) | 4 |
108-8421 Pan Gp-Backrest -Lumbar
| 10***55 | Cover-Speaker | 2 |
| 10***63 | Screw-Machine; (4-40x1-In) | 8 |
| 10***14 | Knob | 4 |
301-4173 Pan Gp-Backrest
| 10***55 | Cover-Speaker | 2 |
| 10***25 | Screw-Machine; (8-32x1-In) | 8 |
| 10***14 | Knob | 4 |
113-5810 Pan Gp-Seat
| 09***92 | Locknut; (M6x1-Thd) | 2 |
| 10***14 | Knob | 4 |
| 11***10 | Pan Group-Seat | 1 |
8x-2385 Panel Gp-Cab -High Profile
| 08***91 | Bolt; (M10x1.5x55-mm) | 1 |
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 10***00 | Fitting As-Air Conditioner; (Quick Disconnect)(Refrigerant) | 2 |
122-9575 Panel Gp-Cab
| 12***75 | Panel Group-Cab; -Instrument | 1 |
| 1L***79 | Elbow-Pipe; (3/8 In Pipe) | 1 |
| 4S***62 | Clip 25.4mm(1 In.)Width | 3 |
129-8614 Panel Gp-Cab -High Profile
| 12***14 | Panel Group-Cab; -High Profile | 1 |
| 2Y***09 | Seal-Wire | 2 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 2 |
8x-2375 Panel Gp-Cab -Low Profile
| 11***04 | Duct-Rh | 1 |
| 11***05 | Duct-Lh | 1 |
| 12***22 | Panel-Cab | 1 |
8w-7310 Panel Gp-Instrument
| 11***18 | Arm | 2 |
| 11***19 | Bracket | 4 |
| 11***20 | Block | 4 |
210-2270 Recliner Gp-Seat
| 14***18 | Bracket As | 2 |
| 1F***50 | Nut Rops Support | 1 |
| 1P***78 | Cap | 2 |
116-3100 Rops Ar
| 11***00 | Rops Ar | 1 |
| 12***98 | Indicator As-Fuel Level | 1 |
| 12***15 | Voltmeter Group; (Instrument Panel) | 1 |
8w-7417 Rops Ar
| 11***86 | Track Group | 1 |
| 12***95 | Indicator As-Articulation | 1 |
| 12***98 | Indicator As-Fuel Level | 1 |
8x-2241 Rops Gp
| 11***86 | Track Group | 1 |
| 14***15 | Indicator As-Articulation | 1 |
| 15***40 | Indicator As-Fuel Level | 1 |
118-2556 Rops Gp -Enclosed, Low Profile
| 11***56 | Rops Group; -Enclosed, Low Profile | 1 |
| 3C***84 | Screw-Machine; (M5x0.8 Bg Thd) | 4 |
| 3T***59 | Bracket | 1 |
8x-2248 Rops Gp
| 11***86 | Track Group | 1 |
| 18***33 | Voltmeter Group; (Quad Gauge Module) | 1 |
| 18***34 | Indicator As-Articulation; (Articulation) | 1 |
139-4612 Screen Gp-Sun -Rear
| 10***53 | Mounting | 4 |
| 10***15 | Pad (Rh) | 1 |
| 10***16 | Pad (Lh) | 1 |
156-1148 Seat Belt Gp
| 00***81 | Ring-Retaining | 2 |
| 11***09 | Pan As-Seat | 1 |
| 11***67 | Kit-Back Tilt; (Includes Parts Marked N) | 1 |
122-4617 Seat Belt Gp -Retractable
| 12***17 | Seat Belt Group; -Retractable-Operator | 1 |
| 13***43 | Plate As-Lumbar | 1 |
| 16***83 | Knob-Lumbar | 1 |
222-0345 Seat Belt Gp -Retractable
| 10***81 | Glass; (Low Profile/Rear) | 1 |
| 11***57 | Glass; (Side) | 2 |
| 14***09 | Glass; (Lower Front) | 2 |
8y-3792 Seat Belt Gp -Retractable
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 10***71 | Pin As | 2 |
| 10***53 | Mounting | 4 |
116-1965 Seat Belt Gp -Retractable
| 10***23 | Shaft As-Lumbar | 1 |
| 10***24 | Pan-Lumbar | 1 |
| 11***65 | Seat Belt Group; -Retractable | 1 |
114-1183 Seat Gp -Cloth, Lumbar
| 10***72 | Glass; (Rear)(High Profile) | 1 |
| 11***83 | Seat Group; -Cloth, Lumbar | 1 |
| 14***09 | Glass; (Lower Front) | 2 |
301-4174 Seat Gp -Cloth
| 10***35 | Film-Identification; (Indicator Light) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 12 |
| 11***15 | Gasket | 1 |
175-1504 Seat Gp -Cloth
| 10***35 | Film-Identification; (Indicator Light) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 11***15 | Gasket | 1 |
8y-3912 Seat Gp -Cloth
| 10***72 | Glass; (Rear)(High Profile) | 1 |
| 11***06 | Glass; (Side) | 2 |
| 14***09 | Glass; (Lower Front) | 2 |
8y-4005 Seat Gp -Vinyl
| 12***59 | Panel | 1 |
| 12***46 | Plate As | 2 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 4 |
114-1185 Seat Gp -Vinyl, Lumbar
| 10***35 | Film-Identification; (Indicator Light) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 8 |
| 11***85 | Seat Group; -Vinyl, Lumbar | 1 |
8y-6851 Seat Gp-Static -Cloth
| 8W***27 | Insulation Group-Weather | 1 |
| 8X***41 | Rops Group | 1 |
| 8X***75 | Washer Group-Window; -Front-Low Profile | 1 |
8x-8940 Seat Gp-Static -Cloth
| 10***35 | Film-Identification; (Indicator Light) | 1 |
| 10***91 | Screw; (Flat Head) (No.6-20x0.5in) | 12 |
| 11***15 | Gasket | 1 |
8y-6852 Seat Gp-Static -Vinyl
| 12***75 | Panel Group-Cab; -Instrument | 1 |
| 3V***94 | Plug-Button | 1 |
| 5P***00 | Key Total 2 Pieces Per Unit; (Literature Compartment) | 1 |
8x-8945 Seat Gp-Static -Vinyl
| 03***14 | Bolt-Self Locking; (1/4unc X 1/2) | 1 |
| 10***67 | Washer-Hard; (7.2x25x2-mm Thk) | 1 |
| 17***90 | Spring | 1 |
155-5958 Seat Gp-Suspension -Cloth, Lumbar
| 15***58 | Seat Group-Suspension; -Cloth, Lumbar | 1 |
200-3814 Seat Gp-Suspension -Cloth
| 03***43 | Nut; (5/16-18 Thd) | 4 |
| 11***36 | Screw-Flat Head; (5/16-18x0.875-In) | 4 |
| 20***14 | Seat Group-Suspension; -Cloth, Air | 1 |
113-1689 Seat Gp-Suspension
| 11***89 | Seat Group-Suspension; -Vinyl | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 4D***32 | Locknut (7/16-20 Thd) | 1 |
8y-4951 Seat Gp-Suspension -Vinyl
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 03***87 | Washer; (16.75x50.8x4.76-mm Thk) | 2 |
| 10***72 | Glass; (Rear)(High Profile) | 1 |
156-7778 Seat Gp-Suspension -Cloth, Lumbar
| 03***43 | Nut; (5/16-18 Thd) | 4 |
| 11***36 | Screw-Flat Head; (5/16-18x0.875-In) | 4 |
| 15***78 | Seat Group-Suspension; -Cloth, Lumbar | 1 |
112-9105 Seat Gp-Suspension -Vinyl
| 11***05 | Seat Group-Suspension; -Vinyl | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 4D***32 | Locknut (7/16-20 Thd) | 1 |
112-9104 Seat Gp-Suspension -Cloth
| 10***04 | Plate | 1 |
| 11***04 | Seat Group-Suspension; -Cloth | 1 |
| 13***26 | Block | 2 |
154-5732 Seat Gp-Suspension -Cloth
| 15***32 | Seat Group-Suspension; -Cloth | 1 |
| 1A***50 | Bolt (7/16-20x1.75in); (7/16-20x1.75-In) | 1 |
| 1L***80 | Bolt; (7/16-20x1.5-In) | 1 |
8y-4194 Seat Gp-Suspension
| 11***56 | Rops Group; -Enclosed, Low Profile | 1 |
| 15***59 | Film-Instruction; (Do Not Drill, Weld Rops) | 2 |
| 2A***85 | Mounting Group-Rops; -Enclosed | 1 |
8w-6318 Support Gp-Seat
| 09***78 | Pin-Spring | 1 |
| 09***14 | Pin, Clevis | 1 |
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
113-5800 Suspension Gp-Seat
| 09***78 | Pin-Spring | 1 |
| 09***14 | Pin, Clevis | 1 |
| 10***21 | Pan Group-Backrest; -Seat Back | 1 |
155-5959 Suspension Gp-Seat -Air
| 0T***44 | Bolt (1.25" Long) | 1 |
| 15***59 | Suspension Group-Seat; -Air | 1 |
| 17***84 | Extension Group-Backrest; (Cloth) | 1 |
8x-2650 Valve Gp-Air Control
| 09***43 | Pin-Cotter | 2 |
| 14***88 | Locknut-Flange; (3/8-16-Thd) | 8 |
| 16***25 | Cushion As | 1 |
8x-9680 Washer Gp-Window -Rear
| 11***65 | Seat Belt Group; -Retractable | 1 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
| 8Y***52 | Seat Group-Static; -Vinyl | 1 |
125-4342 Washer Gp-Window -Front
| 08***68 | Washer; (13x27.5x2.5-mm Thk) | 2 |
| 11***79 | Adjuster Group-Seat | 1 |
| 11***94 | Boot As | 1 |
8x-9675 Washer Gp-Window -Front
| 11***65 | Seat Belt Group; -Retractable | 1 |
| 8X***75 | Washer Group-Window; -Front-Low Profile | 1 |
| 8Y***51 | Seat Group-Static; -Cloth | 1 |
150-5106 Window Gp-Cab -Rh
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
125-8847 Window Gp-Cab -Lh
| 11***04 | Seat Group-Suspension; -Cloth | 1 |
| 12***47 | Window Group-Cab; -Lh | 1 |
| 9X***41 | Screw-Truss Head (M10x1.50x20mm); (Truss Head) (M10x1.5x20mm) | 6 |
125-8846 Window Gp-Cab -Rh
| 08***68 | Washer; (13x27.5x2.5-mm Thk) | 2 |
| 11***79 | Adjuster Group-Seat | 1 |
| 11***94 | Boot As | 1 |
150-5107 Window Gp-Cab -Lh
| 11***05 | Seat Group-Suspension; -Vinyl | 1 |
| 15***07 | Window Group-Cab; -Lh | 1 |
| 9X***41 | Screw-Truss Head (M10x1.50x20mm); (Truss Head) (M10x1.5x20mm) | 6 |
134-8232 Window Gp-Cab -Side Sliding-High Profile
| 11***05 | Seat Group-Suspension; -Vinyl | 1 |
| 13***32 | Window Group-Cab; -Side Sliding-High Profile | 1 |
| 9X***41 | Screw-Truss Head (M10x1.50x20mm); (Truss Head) (M10x1.5x20mm) | 6 |
139-6128 Window Gp-Cab -Side Sliding-Low Profile
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
139-6129 Window Gp-Cab -Side Sliding High Profile
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
134-8233 Window Gp-Cab -Side Sliding-Low Profile
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***00 | Suspension Group-Seat; -Cloth | 1 |
126-0961 Window Gp-Vent -Cab
| 11***42 | Armrest Group; -Lh | 1 |
| 11***45 | Armrest Group; -Rh | 1 |
| 11***83 | Seat Group; -Cloth, Lumbar | 1 |
155-7451 Wiper Ar-Window -Rear
| 15***51 | Wiper Ar-Window; -Rear | 1 |
| 17***87 | Setscrew; (1/4-20-Thd) | 4 |
| 17***35 | Block Kit; (Includes Bolt, Washers, Blocks And Setscrews) | 1 |
155-7450 Wiper Ar-Window -Rear
| 09***81 | Spacer; (10.5x20x10.0mm Thk) | 1 |
| 15***32 | Seat Group-Suspension; -Cloth | 1 |
| 15***50 | Wiper Ar-Window; -Rear | 1 |
8x-2910 Wiper Gp-Window -Rear
| 10***17 | Bumper | 4 |
| 12***57 | Shaft | 2 |
| 12***28 | Kit-Roller; (Incls Parts Marked S) | 1 |
125-4345 Wiper Gp-Window -Front
| 10***45 | Cover | 1 |
| 10***65 | Pad; (Round) | 1 |
| 12***45 | Wiper Group-Window; -Cab Front Window | 1 |
8x-2810 Wiper Gp-Window -Front
| 10***03 | Fastener | 20 |
| 10***94 | Kit-Tether Belt; (Suspension Seat)(Seat Suspension) | 1 |
| 10***95 | Kit-Suspension Roller; (Suspension Seat)(Seat Suspension) | 1 |
8x-2911 Wiper Gp-Window -Rear-High Profile
| 10***45 | Cover | 1 |
| 10***65 | Pad; (Round) | 1 |
| 14***95 | Hose; (650-cm Each) | 0 |
3t-7068 Motor Gp-Window Wiper
| 10***26 | Instrument Group | 1 |
| 10***52 | Sensor Group-Speed | 1 |
| 3T***68 | Wiper Group-Windshield; -Rear | 1 |
Power Train
104-4218 Autoshift Ar
| 10***18 | Autoshift Ar; -Transmission | 1 |
| 14***72 | Service Group-Power Train | 1 |
| 3E***63 | Switch As; (24-Volt)(Rear Floodlight) | 1 |
144-2205 Case & Parts Gp-Planetary
| 10***03 | Kit; (Receptacle) (3-Pin) (Includes Receptacle As & Wedge) | 1 |
| 10***87 | Sensor Group-Speed; (Transmission Output) | 1 |
| 11***45 | Plate As | 1 |
9w-5128 Case & Parts Gp-Planetary
| 10***87 | Sensor Group-Speed; (Transmission Output) | 1 |
| 10***88 | Wire As | 1 |
| 10***89 | Guard As | 1 |
8w-5513 Chain Gp-Drive
| 6G***31 | Link (Connector) | 1 |
| 8W***13 | Chain Group-Drive; -First, Third | 1 |
| 8X***26 | Chain Group; (Drive) | 4 |
6y-2302 Clutch Gp-Transmission -Reverse, Second
| 10***81 | Spring-Wave | 1 |
| 11***23 | Plate-Clutch | 9 |
| 1P***04 | Plug-Metal Cup | 1 |
159-9228 Clutch Gp-Transmission -Forward
| 10***51 | Disc-Friction | 2 |
| 13***19 | Bearing-Roller (Inner) | 1 |
| 13***25 | Gear As; (50-Teeth)(50 Teeth) | 1 |
159-9229 Clutch Gp-Transmission -Reverse, Second
| 10***81 | Spring-Wave | 1 |
| 11***23 | Plate-Clutch | 9 |
| 13***19 | Bearing-Roller (Inner) | 1 |
6y-2301 Clutch Gp-Transmission -Forward
| 10***51 | Disc-Friction | 2 |
| 11***23 | Plate-Clutch | 6 |
| 1P***04 | Plug-Metal Cup | 1 |
8e-9317 Clutch Gp-Transmission -High, Low
| 10***81 | Spring-Wave | 1 |
| 11***23 | Plate-Clutch | 5 |
| 3B***21 | Race And Roller Assem. (Inner) | 1 |
6y-2305 Clutch Gp-Transmission -First, Third
| 10***81 | Spring-Wave | 2 |
| 11***23 | Plate-Clutch | 8 |
| 3B***21 | Race And Roller Assem. (Inner) | 1 |
8w-5915 Control Gp-Differential Lock
| 13***20 | Hose As | 1 |
| 13***41 | Adapter-90 Degree | 1 |
| 14***95 | Valve & Mtg Group-Diff Lock | 1 |
6y-7822 Control Gp-Transmission Hyd
| 11***61 | Manifold | 1 |
| 1T***38 | Washer | 2 |
| 3E***06 | Bolt; (M8x1.25x130-mm) | 2 |
6y-7821 Control Gp-Transmission Hyd
| 11***88 | Switch As-Pressure; (Manual Modulation) | 1 |
| 14***92 | Switch As-Temperature; (Transmission Oil) | 1 |
| 1T***38 | Washer | 33 |
145-9531 Control Gp-Transmission Hyd
| 14***31 | Clip; (10.5-mm Id) | 1 |
| 14***31 | Control Group-Transmission Hydraulic | 1 |
| 14***33 | Valve Group-Transmission Control | 1 |
4w-5974 Cooler Gp-Transmission Oil
| 1A***29 | Bolt (1-1/8") Tube Assembly To Transfer Drive Case | 8 |
| 2Y***29 | Core As | 1 |
| 4W***74 | Cooler Group-Transmission Oil | 1 |
8e-3366 Coupling Gp-Torsional
| 16***28 | Bolt; (3/8-16-Thd)(3/8-16x1.25 In) | 12 |
| 28***99 | Coupling As | 1 |
| 5M***94 | Washer; Bracket To Tee, Bracket To Block, Tube As. To Tee, Tube As. To Oil Cooler | 12 |
8w-5430 Differential & Bevel Gear Gp
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 2 |
| 03***57 | Bolt; --To Reverse Shaft Bearing Retainer & Forward Shaft Bearing Retainer | 5 |
| 0S***56 | Bolt 4 1/4 In. (108 mm) --Front Support Assembly To Frame | 4 |
8w-5112 Differential Gp
| 10***82 | Gear-Bevel; (24-Teeth) | 1 |
| 10***83 | Gear-Bevel; (24-Teeth) | 1 |
| 14***57 | Gear-Bevel; (54-Teeth) | 1 |
154-2688 Differential Gp
| 10***82 | Gear-Bevel; (24-Teeth) | 1 |
| 10***83 | Gear-Bevel; (24-Teeth) | 1 |
| 15***88 | Differential Group | 1 |
8w-4100 Drive Gp-Final
| 03***35 | Bolt-Self Locking; 2.22cm(.875 In.) Lg | 18 |
| 10***70 | Sprocket; (23-Teeth) | 2 |
| 10***71 | Sprocket; (23-Teeth) | 2 |
8w-5926 Filler Gp-Power Train Oil
| 5D***53 | Capscrew (3/8 - 16 Nc X 1 Gd8, Hex Self-Locking) | 2 |
| 7J***11 | Elbow-Pipe; (1/4-18 Nptf Thd) | 1 |
| 8B***15 | Gasket | 1 |
125-3286 Filter Gp-Oil -Transmission
| 12***42 | Base-Xmsn Oil Filter | 1 |
| 12***86 | Filter Group-Oil; -Transmission | 1 |
| 1R***73 | Filter Element As-Oil; (Advanced Efficiency)(Disposable Transmission Oil) | 1 |
8w-6235 Lines Gp-Transmission Oil
| 00***46 | Elbow; (45 Degree Pipe) | 1 |
| 00***98 | Connector-Hose (3/4-14nptf Thd) | 2 |
| 10***23 | Hose As | 1 |
142-6203 Mounting Gp-Wheel
| 11***69 | Tire Group | 1 |
| 14***03 | Mounting Group-Wheel | 2 |
| 14***32 | Transmission Ar | 1 |
8w-6229 Power Train Ar
| 5F***00 | Seal-O-Ring | 1 |
| 5P***63 | Seal-O-Ring | 1 |
| 6V***19 | Bolt; (M8x1.25x40-mm) | 3 |
9w-5134 Screen Gp-Magnetic -Transmission
| 0S***04 | Bolt (1/2-20x2.5in); (1/2-20x2.5-In) | 4 |
| 3K***96 | Guard-Dirt | 1 |
| 3K***86 | Plug | 1 |
8w-5394 Shaft Gp-Drive -Transmission
| 0L***26 | Plug -13mm(.512 In.) Outside Dia. | 1 |
| 1M***95 | Race & Roller Assem. (Inner) | 1 |
| 2H***90 | Race And Roller Assembly, Including:- | 1 |
6y-2300 Shaft Gp-Input
| 00***53 | Elbow-Pipe; (1/2-14 Nptf Thd) | 2 |
| 1F***88 | Breather As; (Crankcase Pressure) | 2 |
| 2A***38 | Cover | 2 |
8w-4331 Tandem & Cover Gp
| 10***67 | Tire; (14-R24)(14.0 R24 * Xmps Mx) | 1 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
152-4660 Tire & Rim Gp
| 15***60 | Tire & Rim Group | 1 |
146-5519 Tire & Rim Gp
| 14***07 | Tire; (14-R24)(14.0 R24 * Vsw Bs) | 1 |
| 14***19 | Tire & Rim Group | 1 |
| 2D***07 | Stud | 1 |
127-0595 Tire & Rim Gp
| 12***95 | Tire & Rim Group | 1 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
132-3363 Tire & Rim Gp
| 13***63 | Tire & Rim Group | 1 |
| 14***60 | Tire; (14-R24)(14.0 R24 *Xsnoplus Mx) | 1 |
| 2D***07 | Stud | 1 |
112-4044 Tire Gp
| 11***44 | Tire Group | 1 |
112-4045 Tire Gp
| 11***45 | Tire Group | 1 |
128-0470 Tire Gp
| 12***70 | Tire Group | 1 |
112-4046 Tire Gp
| 11***46 | Tire Group | 1 |
112-4047 Tire Gp
| 11***47 | Tire Group | 1 |
141-0744 Tire Gp
| 14***44 | Tire Group | 1 |
| 6Y***00 | Shaft Group-Input; -Transmission | 1 |
| 6Y***01 | Clutch Group-Transmission; -Forward | 1 |
112-3869 Tire Gp
| 11***69 | Tire Group | 1 |
144-2232 Transmission Ar
| 14***05 | Case & Parts Group-Planetary | 1 |
| 14***32 | Transmission Ar | 1 |
| 14***31 | Control Group-Transmission Hydraulic | 1 |
9w-5126 Transmission Ar
| 14***05 | Case & Parts Group-Planetary | 1 |
| 14***31 | Control Group-Transmission Hydraulic | 1 |
| 6Y***00 | Shaft Group-Input; -Transmission | 1 |
8x-5005 Universal Joint Gp
| 6G***79 | Kit-Cartridge Seal; (Includes 3 O-Rings) | 1 |
| 8X***05 | Universal Joint Group; -Main Drive Shaft | 1 |
| 9W***06 | Valve Group-Solenoid | 1 |
174-3705 Valve & Mtg Gp-Diff Lock
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 10***54 | Screw-Adjustment; (M12x1.75x18-mm) | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
144-6295 Valve & Mtg Gp-Diff Lock
| 14***95 | Valve & Mtg Group-Diff Lock | 1 |
| 14***16 | Manifold | 1 |
| 15***64 | Valve Group-Solenoid | 1 |
7t-9073 Valve & Mtg Gp-Diff Lock
| 14***94 | Valve Group-Solenoid; -Diff Lock | 1 |
| 14***16 | Manifold | 1 |
| 6G***79 | Kit-Cartridge Seal; (Includes 3 O-Rings) | 1 |
6y-7823 Valve Gp-Selector & Press Cont
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 10***54 | Screw-Adjustment; (M12x1.75x18-mm) | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
145-9534 Valve Gp-Selector & Press Cont
| 14***34 | Valve Group-Selector & Press Cont | 1 |
| 1S***93 | Strap; (Cable) (0.62in Dia) | 2 |
| 2D***35 | Locknut (Visor To Bracket) | 1 |
6y-7824 Valve Gp-Selector & Press Cont
| 09***07 | Nut; (M12x1.75-Thd) | 1 |
| 10***54 | Screw-Adjustment; (M12x1.75x18-mm) | 1 |
| 10***23 | Adjuster Assem. | 4 |
144-6294 Valve Gp-Solenoid
| 10***02 | Kit-Receptacle; (2-Pin)(Engine Sensor Wiring Harness) | 1 |
| 11***43 | Locknut; (5/16-18-Thd) | 2 |
| 14***50 | Cartridge As | 1 |
154-3064 Valve Gp-Solenoid
| 11***61 | Manifold | 1 |
| 14***67 | Poppet | 1 |
| 14***34 | Valve Group-Selector & Press Cont | 1 |
136-1678 Valve Gp-Solenoid
| 11***43 | Locknut; (5/16-18-Thd) | 1 |
| 13***78 | Valve Group-Solenoid | 1 |
| 14***05 | Coil Assem. | 1 |
9w-0706 Valve Gp-Solenoid
| 10***15 | Cartridge Assem. | 1 |
| 10***47 | Locknut; (5/8-11-Thd) | 1 |
| 14***58 | Coil As | 1 |
145-9533 Valve Gp-Transmission Control
| 11***45 | Tire Group | 1 |
| 14***33 | Valve Group-Transmission Control | 1 |
| 8X***86 | Wheel Group | 1 |
142-6467 Wheel & Tire Ar
| 14***21 | Wheel & Tire Group | 6 |
| 14***67 | Wheel & Tire Ar | 1 |
151-0380 Wheel & Tire Ar
142-6470 Wheel & Tire Ar
| 14***25 | Wheel & Tire Group | 6 |
| 14***70 | Wheel & Tire Ar | 1 |
151-0366 Wheel & Tire Ar
| 14***66 | Wheel & Tire Group | 6 |
| 15***66 | Wheel & Tire Ar | 1 |
142-6469 Wheel & Tire Ar
| 14***22 | Wheel & Tire Group | 6 |
| 14***69 | Wheel & Tire Ar | 1 |
151-0368 Wheel & Tire Ar
| 14***54 | Wheel & Tire Group | 6 |
| 15***68 | Wheel & Tire Ar | 1 |
151-0362 Wheel & Tire Ar
| 14***53 | Wheel & Tire Group | 6 |
| 15***62 | Wheel & Tire Ar | 1 |
151-0381 Wheel & Tire Ar
142-6477 Wheel & Tire Ar
| 14***30 | Wheel & Tire Group | 6 |
| 14***77 | Wheel & Tire Ar | 1 |
142-6461 Wheel & Tire Ar
| 14***16 | Wheel & Tire Group | 6 |
| 14***61 | Wheel & Tire Ar | 1 |
142-6474 Wheel & Tire Ar
| 14***28 | Wheel & Tire Group | 6 |
| 14***74 | Wheel & Tire Ar | 1 |
8x-2487 Wheel & Tire Ar
| 11***47 | Tire Group | 1 |
| 8X***86 | Wheel Group | 1 |
| 8X***87 | Wheel & Tire Ar | 1 |
151-0382 Wheel & Tire Ar
| 14***85 | Wheel & Tire Group | 6 |
| 15***82 | Wheel & Tire Ar | 1 |
151-0392 Wheel & Tire Ar
| 14***76 | Wheel & Tire Group | 6 |
| 15***92 | Wheel & Tire Ar | 1 |
151-0388 Wheel & Tire Ar
| 14***75 | Wheel & Tire Group | 6 |
| 15***88 | Wheel & Tire Ar | 1 |
153-5468 Wheel & Tire Ar
| 15***68 | Wheel & Tire Ar | 1 |
| 15***85 | Wheel & Tire Group | 6 |
151-0365 Wheel & Tire Ar
| 14***63 | Wheel & Tire Group | 6 |
| 15***65 | Wheel & Tire Ar | 1 |
151-0385 Wheel & Tire Ar
| 14***57 | Wheel & Tire Group | 6 |
| 15***85 | Wheel & Tire Ar | 1 |
159-1782 Wheel & Tire Ar
| 15***82 | Wheel & Tire Ar | 1 |
| 20***85 | Wheel & Tire Group | 6 |
151-0364 Wheel & Tire Ar
| 14***60 | Wheel & Tire Group | 6 |
| 15***64 | Wheel & Tire Ar | 1 |
151-0389 Wheel & Tire Ar
| 14***58 | Wheel & Tire Group | 6 |
| 15***89 | Wheel & Tire Ar | 1 |
151-0378 Wheel & Tire Ar
| 14***61 | Wheel & Tire Group | 6 |
| 15***78 | Wheel & Tire Ar | 1 |
204-8786 Wheel & Tire Ar
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***73 | Tire; (14.00-24 12pr G-2 Gy) | 1 |
151-0379 Wheel & Tire Ar
| 14***64 | Wheel & Tire Group | 6 |
| 15***79 | Wheel & Tire Ar | 1 |
151-0393 Wheel & Tire Ar
| 15***93 | Wheel & Tire Ar | 1 |
| 15***67 | Wheel & Tire Group | 6 |
151-0374 Wheel & Tire Ar
| 14***73 | Wheel & Tire Group | 6 |
| 15***74 | Wheel & Tire Ar | 1 |
142-6455 Wheel & Tire Ar
| 14***10 | Wheel & Tire Group | 6 |
| 14***55 | Wheel & Tire Ar | 1 |
151-0375 Wheel & Tire Ar
| 14***56 | Wheel & Tire Group | 6 |
| 15***75 | Wheel & Tire Ar | 1 |
142-6458 Wheel & Tire Ar
| 14***13 | Wheel & Tire Group | 6 |
| 14***58 | Wheel & Tire Ar | 1 |
151-0371 Wheel & Tire Ar
| 14***72 | Wheel & Tire Group | 6 |
| 15***71 | Wheel & Tire Ar | 1 |
142-6464 Wheel & Tire Ar
| 14***19 | Wheel & Tire Group | 6 |
| 14***64 | Wheel & Tire Ar | 1 |
8x-2485 Wheel & Tire Ar
| 11***46 | Tire Group | 1 |
| 8X***85 | Wheel & Tire Ar | 1 |
| 8X***86 | Wheel Group | 1 |
151-0367 Wheel & Tire Ar
| 14***71 | Wheel & Tire Group | 6 |
| 15***67 | Wheel & Tire Ar | 1 |
151-0372 Wheel & Tire Ar
| 14***55 | Wheel & Tire Group | 6 |
| 15***72 | Wheel & Tire Ar | 1 |
112-5589 Wheel & Tire Ar
| 11***89 | Wheel & Tire Ar | 1 |
| 14***07 | Wheel & Tire Group | 6 |
142-6479 Wheel & Tire Ar
| 14***32 | Wheel & Tire Group | 6 |
| 14***79 | Wheel & Tire Ar | 1 |
142-6371 Wheel & Tire Gp
| 14***86 | Tire; (17.5-25) | 1 |
| 14***71 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
153-5467 Wheel & Tire Gp
| 14***29 | Wheel Group | 1 |
| 15***67 | Wheel & Tire Group | 1 |
| 15***51 | Tire; (17.5-R25) | 1 |
142-6322 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 12***54 | Tire; (14.0 R24 * Sg-2b Gy) | 1 |
142-6363 Wheel & Tire Gp
| 14***29 | Wheel Group | 1 |
| 14***63 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6357 Wheel & Tire Gp
| 14***84 | Tire; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***57 | Wheel & Tire Group | 1 |
142-6355 Wheel & Tire Gp
| 12***50 | Tire-Tubeless; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***55 | Wheel & Tire Group | 1 |
142-6330 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***26 | Wheel Group | 1 |
142-6325 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***60 | Tire; (14-R24)(14.0 R24 *Xsnoplus Mx) | 1 |
159-1785 Wheel & Tire Gp
| 14***29 | Wheel Group | 1 |
| 15***85 | Wheel & Tire Group | 1 |
| 18***19 | Tire; (17.5-R25) | 1 |
142-6319 Wheel & Tire Gp
| 10***67 | Tire; (14-R24)(14.0 R24 * Xmps Mx) | 1 |
| 12***20 | Rim As | 1 |
| 14***19 | Wheel & Tire Group | 1 |
142-6373 Wheel & Tire Gp
| 12***51 | Tire; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***73 | Wheel & Tire Group | 1 |
142-6385 Wheel & Tire Gp
| 10***49 | Tire; (17.5-R25) | 1 |
| 14***85 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6364 Wheel & Tire Gp
| 10***35 | Tire; (17.5-R25) | 1 |
| 14***64 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6354 Wheel & Tire Gp
| 14***84 | Tire; (17.5-25) | 1 |
| 14***54 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6376 Wheel & Tire Gp
| 10***49 | Tire; (17.5-R25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***76 | Wheel & Tire Group | 1 |
142-6353 Wheel & Tire Gp
| 14***83 | Tire; (17.5-25) | 1 |
| 14***53 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6366 Wheel & Tire Gp
| 10***35 | Tire; (17.5-R25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***66 | Wheel & Tire Group | 1 |
142-6372 Wheel & Tire Gp
| 14***87 | Tire; (17.5-25) | 1 |
| 14***72 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6360 Wheel & Tire Gp
| 14***29 | Wheel Group | 1 |
| 14***60 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6316 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 12***78 | Tire; (14.00 R24 Tg Rl2f * G-2) | 1 |
142-6307 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***74 | Tire; (14.00-24 12pr G-2 Fs) | 1 |
142-6310 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 0 |
| 14***75 | Tire; (14-24)(14.00-24 12pr G-2 Gn) | 1 |
142-6375 Wheel & Tire Gp
| 14***87 | Tire; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***75 | Wheel & Tire Group | 1 |
142-6332 Wheel & Tire Gp
| 12***50 | Tire-Tubeless; (17.5-25) | 1 |
| 14***32 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6361 Wheel & Tire Gp
| 14***61 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
142-6356 Wheel & Tire Gp
| 14***83 | Tire; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***56 | Wheel & Tire Group | 1 |
142-6367 Wheel & Tire Gp
| 12***51 | Tire; (17.5-25) | 1 |
| 14***67 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
142-6313 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 11***13 | Tire; (14-R24)(14.0 R24 Tg * Xgla2 G-2) | 1 |
142-6328 Wheel & Tire Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***07 | Tire; (14-R24)(14.0 R24 * Vsw Bs) | 1 |
142-6374 Wheel & Tire Gp
| 14***86 | Tire; (17.5-25) | 1 |
| 14***29 | Wheel Group | 1 |
| 14***74 | Wheel & Tire Group | 1 |
204-8785 Wheel & Tire Gp
| 14***04 | Wheel Group | 6 |
| 20***85 | Wheel & Tire Group | 1 |
142-6321 Wheel & Tire Gp
| 10***67 | Tire; (14-R24)(14.0 R24 * Xmps Mx) | 1 |
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
142-6358 Wheel & Tire Gp
| 14***58 | Wheel & Tire Group | 1 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
148-2405 Wheel Ar
| 14***05 | Wheel Ar, Locking Plate | 1 |
| 14***08 | Wheel Group | 6 |
148-2409 Wheel Ar
| 0S***73 | Bolt 50.80 mm(2 In.) Long | 60 |
| 11***27 | Valve Group-Tire | 6 |
| 13***81 | Rim As | 6 |
142-6305 Wheel Ar
| 14***05 | Wheel Ar | 1 |
| 14***04 | Wheel Group | 6 |
142-6226 Wheel Gp
| 14***26 | Wheel Group | 1 |
| 28***25 | Rim As; (14x25) | 1 |
| 4K***81 | Ring-Lock; (Lock) | 1 |
8x-1660 Wheel Gp
| 0S***73 | Bolt 50.80 mm(2 In.) Long | 60 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
142-6229 Wheel Gp
| 11***13 | Valve Group-Tire; (Tire Inflation) | 1 |
| 11***14 | Stem As | 1 |
| 14***26 | Wheel Group | 1 |
142-6304 Wheel Gp
| 14***04 | Wheel Group | 1 |
| 2D***07 | Stud | 1 |
| 2D***08 | Grommmet | 1 |
148-2408 Wheel Gp
| 03***60 | Cup-Roller Bearing | 2 |
| 03***61 | Cone-Roller Bearing | 2 |
| 0S***92 | Bolt--Cover To Flywheel Housing | 2 |
148-2404 Wheel Gp
| 14***29 | Wheel Group | 1 |
| 14***04 | Wheel Group | 1 |
| 2D***07 | Stud | 1 |
8x-2486 Wheel Gp
| 29***07 | Rim As; (10x24) | 1 |
| 2D***54 | Ring-Lock | 1 |
| 8W***66 | Flange As | 1 |
Service Equipment And Supplies
111-1719 Box Gp-Tool
| 11***19 | Box Group-Tool | 1 |
114-5225 Film Gp
| 11***25 | Film Group | 1 |
| 2Y***68 | Plate-Serial Number-Engine | 1 |
| 2Y***09 | Seal-Wire | 2 |
8t-5255 Jack-Hydraulic
| 11***25 | Film Group | 1 |
| 13***58 | Film; (Identification) (On Radiator Filler Cap) (On Near Of Radiator Filler Cap) | 1 |
| 13***67 | Film-Warning; (Unexpected Movement) | 1 |
5m-8212 Plate & Film Gp
| 13***81 | Film-Warning; (Unexpected Movement) | 1 |
| 1P***82 | Plate-Warning; (High Press Cylinder) | 2 |
| 5M***12 | Plate & Film Group | 1 |
116-9442 Plate & Film Gp
| 11***42 | Plate & Film Group | 1 |
116-9439 Plate & Film Gp
| 10***27 | Film-Instruction; (Hydraulic Accumulator)(Hydraulic Accumulator) | 2 |
| 11***39 | Plate & Film Group | 1 |
| 13***89 | Film-Warning; (Unexpected Movement)(Unexpected Movement) | 1 |
116-9390 Plate & Film Gp
| 11***90 | Plate & Film Group | 1 |
| 1P***83 | Plate-Warning; (High Pressure) | 2 |
| 3E***43 | Plate-Instruction; (Hydraulic Accumulator) | 2 |
116-9440 Plate & Film Gp
| 11***40 | Plate & Film Group | 1 |
| 13***83 | Film-Warning; (Unexpected Movement) | 1 |
| 5P***39 | Film-Warning; (Rotating Fan Blades)(On Side Of Fuel Tank) | 6 |
116-9388 Plate & Film Gp -Portuguese
| 11***88 | Plate & Film Group; -Portuguese | 1 |
| 13***81 | Film-Warning; (Unexpected Movement) | 1 |
| 1P***82 | Plate-Warning; (High Press Cylinder) | 2 |
8c-8447 Plate & Film Gp
| 13***82 | Film-Warning; (Unexpected Movement) | 1 |
| 1P***83 | Plate-Warning; (High Pressure) | 2 |
| 3E***43 | Plate-Instruction; (Hydraulic Accumulator) | 2 |
116-9438 Plate & Film Gp
| 11***38 | Plate & Film Group | 1 |
| 13***83 | Film-Warning; (Unexpected Movement) | 1 |
| 3E***44 | Film-Instruction; (Hydraulic Accumulator) | 2 |
116-9387 Plate & Film Gp -Spanish
| 10***27 | Film-Instruction; (Hydraulic Accumulator)(Hydraulic Accumulator) | 1 |
| 11***87 | Plate & Film Group; -Spanish | 1 |
| 13***89 | Film-Warning; (Unexpected Movement)(Unexpected Movement) | 1 |
119-0081 Plate & Film Gp
| 11***81 | Plate & Film Group | 1 |
116-9386 Plate & Film Gp -French
| 11***86 | Plate & Film Group; -French | 1 |
| 13***83 | Film-Warning; (Unexpected Movement) | 1 |
| 3E***44 | Film-Instruction; (Hydraulic Accumulator) | 2 |
Work Tools
107-3415 Bit Gp -14 Ft-56 Std Bits
| 10***15 | Bit Group; -14 Ft-56 Std Bits | 1 |
| 12***08 | Spacer; (10.31x17.45x50.8-mm Thk) | 1 |
| 12***09 | Plate | 1 |
107-3398 Bit Gp-End
| 10***58 | Nut; (10x32-mm) | 2 |
| 10***98 | Bit Group-End | 1 |
| 10***46 | Stop-Slide | 2 |
8w-6227 Blade Ar
| 10***58 | Nut; (10x32-mm) | 2 |
| 10***46 | Stop-Slide | 2 |
| 13***32 | Latch As | 1 |
8w-7465 Blade Gp
| 13***33 | Window Group-Cab; -Side Sliding-Low Profile | 2 |
| 8W***65 | Blade Group; -14 Ft | 1 |
8x-1955 Blade Gp
| 13***32 | Window Group-Cab; -Side Sliding-High Profile | 2 |
| 8X***55 | Blade Group; -12 Ft | 1 |
116-0379 Bracket Gp-Scarifier
| 11***79 | Bracket Group-Scarifier | 1 |
| 12***08 | Spacer; (10.31x17.45x50.8-mm Thk) | 1 |
| 12***09 | Plate | 1 |
107-3397 Edge Gp-Cutting -7 Ft
| 10***97 | Edge Group-Cutting; -7 Ft | 1 |
| 12***46 | Window Group-Cab; -Rh | 1 |
| 12***47 | Window Group-Cab; -Lh | 1 |
107-3396 Edge Gp-Cutting -6 Ft
| 10***96 | Edge Group-Cutting; -6 Ft | 1 |
| 12***08 | Spacer; (10.31x17.45x50.8-mm Thk) | 1 |
| 12***09 | Plate | 1 |
110-5327 Extension Gp-Blade -Lh
| 11***27 | Extension Group-Blade; -Lh | 1 |
| 8X***10 | Wiper Group-Window; -Rear | 1 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
110-5326 Extension Gp-Blade -Rh
| 11***26 | Extension Group-Blade; -Rh | 1 |
| 15***06 | Window Group-Cab; -Rh | 1 |
| 15***07 | Window Group-Cab; -Lh | 1 |
8x-1935 Lift Gp-Blade
| 8X***35 | Lift Group-Blade | 1 |
| 8X***11 | Wiper Group-Window; -Rear-High Profile | 1 |
| 8X***80 | Washer Group-Window; -Rear | 1 |
9w-7467 Mounting Gp-Ripper
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
| 12***55 | Blade As-Wiper; (335-mm)(High Profile Front Lower) | 2 |
| 12***03 | Shaft As; (Wiper Lower Rh) | 1 |
9w-7603 Ripper Ar
| 10***44 | Motor Group-Window Wiper; (24-Volt)(24-Volt) | 2 |
| 12***54 | Arm-Window Wiper; (Front, Lower) | 2 |
| 12***55 | Blade As-Wiper; (335-mm)(High Profile Front Lower) | 2 |
8j-7024 Ripper Gp
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 2H***20 | Lockwasher (11.38mm Id) | 1 |
| 3K***82 | Fuse; (10-Ampere) | 1 |
145-2244 Ripper Gp
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 14***44 | Ripper Group | 1 |
| 20***07 | Motor Group-Window Wiper; (24-Volt)(Front, Upper) | 1 |
108-1104 Scarifier Ar -Vee Type
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 10***04 | Scarifier Ar; -Vee Type | 1 |
| 2H***20 | Lockwasher (11.38mm Id) | 1 |
113-0704 Scarifier Ar -Straight
| 01***16 | Setscrew; (8-32x0.5-In) | 1 |
| 11***04 | Scarifier Ar; -Straight | 1 |
| 20***07 | Motor Group-Window Wiper; (24-Volt)(Front, Upper) | 1 |
111-3883 Scarifier Gp -Straight Type
| 10***44 | Motor Group-Window Wiper; (24-Volt)(24-Volt) | 1 |
| 11***83 | Scarifier Group; -Straight Type | 1 |
| 20***07 | Motor Group-Window Wiper; (24-Volt)(Front, Upper) | 1 |
8x-6080 Scarifier Gp -Vee Type
| 3T***68 | Wiper Group-Windshield; -Rear | 1 |
| 4B***83 | Washer .32 cm(.125 In.)Thick; (20.6x37.5x3.5-mm Thk) | 2 |
| 5P***15 | Washer-Mount 9w***75 Fuel Level Sensor | 2 |
4k-3330 Tooth Gp-Scarifier
| 10***88 | Film-Stripe; (Cat)(Engine Enclosure) | 2 |
| 10***89 | Film-Stripe; (Rh)(Engine Enclosure) | 1 |
| 10***87 | Film-Stripe; (Lh)(Engine Enclosure) | 1 |
8j-1434 Tooth Gp-Ripper -Straight
| 12***49 | Tool Box | 1 |
| 5K***07 | Bolt 5t***11 Bracket To Lh Radiator Guard | 4 |
| 5P***75 | Washer-Hard; (10.2x22.5x3-mm Thk)(Shield To A/C) | 4 |
160H NA serial number reference
The PIN/serial plate on a 160H NA is riveted to the mainframe, usually on the left side of the front frame rail ahead of the moldboard lift cylinder support near the operator's cab; some units carry a duplicate tag near the engine compartment on the right side of the frame. The PIN reads as a 3-character prefix followed by a sequential machine number - the prefix identifies the model and configuration release (e.g. 9EJ, 3HR, 3GM), while the trailing digits are just the build sequence within that prefix.
| Prefix | Identifies | Notes |
|---|---|---|
| 9EJ | 160H NA motor grader | North America-spec prefix for the 160H NA civil grader. Appears in the combined 12H/140H/160H NA electrical manual line and in a parts listing explicitly tagged 160H NA. Runs the Cat 3176-family diesel used across the 160H NA line, per factory specalog. Reported as an early NA prefix in the line; exact production dates not independently verified - confirm with dealer. |
| 3HR | 160H NA motor grader | North America-spec prefix for the 160H NA civil grader, grouped with 9EJ and 3GM in NA-version manual listings. Same 3176-family diesel as the other NA prefixes. Thinly documented outside manual title listings - confirm exact serial break and production dates with dealer. |
| 3GM | 160H NA motor grader | North America-spec prefix for the 160H NA civil grader. Appears in a combined 140H/160H NA operation and maintenance manual alongside 9EJ, and in standalone 160H NA service manual listings. Same 3176-family diesel as the other NA prefixes. |
Frequently asked questions
What engine does the Caterpillar 160H NA use?
The 160H NA runs a Cat 3176-family turbocharged, air-to-air aftercooled inline-six diesel. Earlier production used a fixed-rating 3176C ATAAC arrangement at 149 kW (200 hp) net; later production used a Variable Horsepower (VHP) / VHP Plus 3176 ETA arrangement that steps output by gear, from 134 kW (180 hp) net up to roughly 149-164 kW (200-220 hp) net in the top gears, meeting Tier II/Stage II emissions. Confirm which arrangement is fitted before ordering engine parts or setting valve lash.
What is the operating weight of the Caterpillar 160H NA?
Standard operating weight runs 15,676-16,280 kg (34,560-35,890 lb) depending on tire and rim option, with gross machine weight reaching roughly 22,300-23,280 kg (49,165-51,325 lb) under full attachment allowance. Treat the figure as a range; exact weight varies by configuration.
What replaced the Caterpillar 160H?
Caterpillar succeeded the H-series 160H with the M-series 160M, which brought electronic hydraulic implement controls and a different engine platform. The H-series itself had replaced the earlier G-series graders when it launched in the mid-1990s.
What 160H NA owners discuss
What powertrain issues come up most often with the 160H NA in the field?
Transmission clutch/solenoid faults are the most common driveline complaint. Missing gears - often 1st forward, or a mid-range forward gear while reverse stays fully functional - trace to a solenoid or modulation valve control fault more often than to clutch pack wear. Delayed or slow upshifts, especially into 4th-5th, show up on higher-hour machines and sometimes clear after a transmission oil and filter service, which points to worn valve bodies or oil starvation before assuming a full rebuild is needed. If two solenoids in the transmission control valve group test open or shorted, expect intermittent forward gear dropout even with correct supply voltage present at the connector. Have your dealer verify solenoid resistance and pull ECM fault codes before committing to a transmission teardown.
Are there known engine quirks tied to the 3176C ATAAC used in the 160H NA?
This engine family uses an aluminum spacer deck between the block and cylinder head. The gasket at that joint is a known wear point, and when it fails coolant more often turns up in the engine oil (milky oil, rising crankcase level) than as an external leak. Early boost sensor installations sit low on the engine where the sensor hose can trap condensation; in cold weather that trapped water can freeze and force the engine into a low-boost, reduced-power mode until it thaws or the sensor routing is corrected. Intermittent stalling or an erratic idle on these engines is commonly traced to a failing engine speed/timing sensor or a chafed harness connector rather than a fuel delivery fault. Have your dealer verify coolant-in-oil condition and boost sensor routing before assuming a major engine repair.
What fuel system behavior should 160H NA owners watch for?
A grader that sputters at idle and loses power under load or climbing a grade, with the symptom getting worse over days or weeks, points first at water or contamination in the fuel rather than an engine fault. Operators who catch this early typically find water in the primary fuel/water separator bowl on a routine drain, which is also a cue to check fuel storage and tank cap seals, not just the machine itself. If rough running persists after the fuel system tests clean, suspicion shifts to the engine's electronic controls and wiring rather than the fuel circuit.
Is a freewheeling circle drive a defect on this grader family?
Not necessarily. The circle drive on this control valve platform can rotate under load, or even move with the control lever in neutral, due to cavitation in the circle valve under certain conditions; this behavior was addressed by a running production change to the valve stem, so an earlier-build machine can show it as built rather than as a developing fault. The circle drive relies on a slip clutch rather than a dedicated relief valve, so a circle that slips under normal working loads calls for inspecting and shimming that clutch pack, not chasing implement system relief pressure. Separately, steering or lift pressure loss on this valve family more often traces to a worn control valve spool or a pump return line issue than to a failed pump outright.
What wear patterns show up on the circle, drawbar, moldboard, and tires?
The standard field check is lifting the drawbar/circle/moldboard assembly off the ground and watching for lift cylinder rod travel before the cutting edge actually starts to move; any lag means the moldboard slides, circle shoes, or drawbar ball stud have gone loose and need adjustment or wear strip replacement. These surfaces need frequent inspection because looseness costs grading accuracy directly, not just component life. Front wheel lean is normal operator technique for side-draft cuts and moldboard discharge, not itself a wear problem, but a machine run without adjusting lean, or leaned the wrong way for the cut being made, shows faster and more uneven front tire wear and sidewall damage than one worked with proper lean technique.
What electrical or sensor complaints come up on the 160H NA?
Beyond the engine speed sensor issues noted above, owners report inaccurate service hour meter readings and general gauge or sender flakiness traced to connector corrosion or a chafed harness section rather than the gauges themselves. Symptoms consistent with a failing engine-to-cab harness - fault codes that come and go, sensors that read fine one moment and fault the next during a wiggle test, or an erratic gauge sweep - are common on machines in this age and hour range and should prompt a harness and connector inspection before sensors are swapped on a hunch. Have your dealer verify wiring continuity and connector condition before replacing sensors.
What should a buyer check before purchasing a used 160H NA?
Lift the drawbar, circle and moldboard off the ground and check for lag before the cutting edge moves; looseness there is a common wear item and a fair bargaining point rather than a walk-away. Run the transmission through its full range of forward and reverse gears on a real test drive, not just at idle in the yard, since dropped or delayed forward gears are a known failure pattern tied to the solenoid and modulation valve group. Check oil color for a milky tint to rule out a head gasket/spacer-deck coolant leak on the engine. Confirm the circle drive does not freewheel with the control lever in neutral, and check tandem and final drive oil condition rather than relying on hour meter figures alone, given known meter accuracy complaints. Look at tire and cutting edge/moldboard wear against the hours claimed, and check that the fuel/water separator is clean with no history of contamination. Have your dealer run a full inspection and pull the fault code history before final purchase.
Compiled from owner and technician discussions across the industry — experiences vary by serial range and machine history.
Need a specific 160H NA part?
Search live OEM part data, check fitment, and cross-reference alternatives with Heavy Parts AI.